2014 - colorama · steel (incl. galvanized), aluminum, fiberglass plastic, oem substrates*. keep...

2014catalogue

CAR REFINISH CONSUMABLES

GB

1catalogue 2014

Dear customers,

We are glad to introduce a comprehensive range of high-quality car refinish con-sumables С.А.R.FIT.Traditional German quality, proven manufacturing recipes and technologies ensure perfect finish results meeting the requirements of modern applications.

Among other things, the catalogue features a new С.А.R.FIT product series BLACK LABEL, part of the unique system of new generation polyester materials for spe-cialized applications.

All materials covered in the catalogue can be used with all paint systems without compromising application technology, which is another proof of С.А.R.FIT’s high quality.

2catalogue 2014

Suitable substrates Brush application

Cleaning Airless application

Application viscosity Material thickness

Use of measuring stick Air drying/flash-off

Mixing ratio by volume: 2 components; 3 components

Low baking

Addition of hardener/catalyst Infrared drying (short wave)

Pot life of liquid materials Orbital sander

Nozzle size, mm Flat-bed sander

Inlet pressure Dry sandind by hand

Application with putty knife/pot life of the putty

Wet sandind by hand

Shake can well Application subsequent material

Number of coats / material application Polishing

Spray can application Keep frost protected

Cartridge gun Keep out of direct sunlight

UB Suction gun Attention

Paint roller application See TDS

3catalogue 2014

Contents

Black Label Series 4

Putties 14

Clearcoats 19

Primers, Fillers 23

Thinners, Cleaners 28

Bodycoats, Cabin coats 30

Sealants 32

Ancillary material 34

Masking 35

Cloths 39

Polishing materials 41

Accessories 42

4catalogue 2014

Fill&Fine Putty anticorrosion protectionDescription Two component basic universal filling putty for eliminating major and medium mechanical damages.First ever polyester putty with anticorrosive properties.

Application Universal filling putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free

surface, thus enabling the refinisher to use one product at all stages of repair (no need to use finishing putty)

• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid paintwork defects (deep sanding marks)

• Easy to apply in thin and thick coats• Does not clog the sandpaper• Anticorrosive properties.

SubstratesAll kinds of steel, flexible aluminium, OEM substrates*.

VOC < 250 g/LEU limit value: 2004/42/IIB(b)(250)

Articles Description Pcs. / pack

2-110-1000 1 kg, w/hardener 12

BLACK LABEL SERIES

Substrates to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded

Add 2 – 3% BPO Hardener by weight

Pot life: 3 – 5 min

16 – 30 min depending on ambient temperature

With P80 – 180

First with P150, then with P240

Keep away from direct sunlight

Xn

Harmful

Color redDensity 1900 g/lFlash point 31 °C

Substrate pretreatment

Application*

Further treatment

Storage

Safety information

Standard sanding method

Recommended sanding method

With P80 – 320 (intermediate sanding step of 100 grit should be observed)

Technical data

AntiCorroSion

5catalogue 2014


Light&Soft PuttyDescription Two component polyester filling putty with a glass microsphere.

Application Basic/filling putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly

speeds up sanding and helps avoid paintwork defects (deep sanding marks)• Specific formula of the putty with hollow glass microspheres significantly reduces its density,

improves its filling power and leaves light gloss on the surface until cure is complete, allowing for better control of the repair zone

• Excellent sandability even a few days after application• Recommended for use on large body parts: roof, doors, trunk lid, bonnet, etc.

SubstratesAll kinds of steel, fiberglass plastics, OEM substrates*.


2-131-1300 1.3 kg, w/hardener 10

BLACK LABEL SERIES





With P80 – 180



Xn

Harmful

Color beigeDensity 1260 g/lFlash point 31 °C


Application*

Further treatment

Storage

Safety information




Technical data

Low DenSity

6catalogue 2014

BLACK LABEL SERIES

Glas&Soft Putty


2-170-1000 1 kg, w/hardener 12


Description Two component fiberglass-filled polyester putty.Perfect choice for the repair of body parts with significant mechanical damages, loss of carrier function and through holes. When applied, it produces a coat of significant thickness which cures in a uniform manner. Due to its homogeneous structure and a minimum number of pinholes, makes application of finishing putties unnecessary.

Application Fiberglass putty for eliminating car and commercial vehicle body imperfections.

Characteristics• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly

speeds up sanding and helps avoid deep sanding marks• Restores the carrier function of damaged parts• Easy application and uniform cure in thick coats• No sandpaper clogging• No need in additional processing with a finishing putty• Very good adhesion to steel, galvanized steel, flexible aluminium and fiberglass plastics.

SubstratesAll kinds of steel, flexible aluminium, fiberglass plastics, OEM substrates*.






Xn

Harmful

Color blue/greenDensity 1750 g/lFlash point 31°C


Application*

Further treatment

Storage

Safety information

With P80 – 180





Technical data

7catalogue 2014

BLACK LABEL SERIES


Light Violet Putty


2-190-1000 1 L, w/hardener 10

Description Two-component polyester finishing putty. Due to its relatively low viscosity, the putty is easy to apply and spread with a putty knife, efficiently filling minor surface imperfections.

Application For filling minor defects, irregularities and pinholes on car and commercial vehicle body paintworks, as well as scratches resulting from sanding with P80-120-180 grit abrasives.

Characteristics• Due to its low viscosity, efficiently fills scratches resulting from sanding with P80-120-180, which

enables it to be directly applied onto polyester materials and other coatings sanded with P80-120-180 abrasives

• Smooth pinhole-free surface produced upon drying, together with good filling properties, saves time and subsequently applied materials

• Easy to apply in thin coats and process with P220-320 grit abrasives (machine sanding) which ensures a high-quality finish

• Drying and sanding with P220-320 grit abrasives can be followed by wet-on-wet filler application and subsequent topcoat application.

SubstratesFillers, primer-fillers, OEM substrates*.


Application*

Further treatment

Technical data

Storage

Safety information

Color violetDensity 1250 g/LFlash point 31°C


– Add 3-4% BPO Hardener (< 20°С)– Add 2-3% BPO Hardener (> 20°С)


With P220 – 320

With P220 – 320

Initial machine sanding of thick putty coats can be done with P180

Keep away from direct sunlight Keep away from direct sunlight

Xn

Harmful

When applied in thicker coats, first apply a thin coat to improve adhesion and eliminate pinholes

20 – 30 min depending on ambient tem-perature

Recoat with 2К fillers and/or base coats and clear coats

8catalogue 2014






Xn

Harmful

Color metallicDensity 1780 g/LFlash point 31°C


Application*

Further treatment

Technical data

Storage

Safety information

Alu&Soft Putty


2-180-1000 1 kg, w/hardener 12

VOC: < 250 g/LEU limit value: 2004/42/IIB(b)(250)

Description Two component aluminium-filled polyester putty.It is used as a basic filling putty, particularly, in the repair of metal surfaces exposed to high temperature and mechanical abuse.

Application For repairs on metal surfaces of cars and commercial vehicles.

Characteristics• Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free

surface, thus enabling the refinisher to use one product at all stages of repair (no need to use a finishing putty)

• Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid deep sanding marks

• Retains its shape in thin coats• Easy to sand with Р150 grit abrasives, providing a smooth transition between the repair and the

undamaged surrounding area• Excellent adhesion.

SubstratesAll kinds of steel, flexible aluminium, OEM substrates*.

BLACK LABEL SERIES

With P80 – 180





9catalogue 2014

BLACK LABEL SERIES

*Do not apply on one component (etch and anticorrosive) primers and thermoplastics. Application on paintworks is not recommended.


Application*

Further treatment






Carbon Putty


2-135-1300 1.3 kg, w/hardener 10

Description Fiber filled extra light 2К polyester putty for badly damaged surfaces requiring extensive repair. It has been developed for restoring damaged surfaces, increasing the mechanical strength of the repaired element.

Application For repairs on metal surfaces of cars and commercial vehicles.

Characteristics• It can be sanded with comparatively high grit abrasives (P120 – P150) • This putty is almost as hard as finish coating that provide a smooth transition between the repair and the undamaged surrounding area during sanding • It can be applied directly prior to filler • Due to its paste-like consistency, the putty is easy to apply in 2–4 mm coats • Perfectly suitable for sanding by machine or wet sanding by hand • Does not clog abrasives • Easy to work also on surfaces with complicated shapes even when applying thicker layers • Very good adhesion.

SubstratesSteel (incl. galvanized), aluminum, fiberglass plastic, OEM substrates*.


Xn

Harmful

Color blackDensity 1100-1200 g/LFlash point 27°C

Technical data

Storage

Safety information

With P80 – 180





10catalogue 2014


4-410-3500 filler 3.5 L 2

4-410-1200 1 L filler + 0.2 L hardener 12

4-400-0700 hardener 0.7 L 12

VOC: <540 g/LEU limit value: 2004/42/IIB(c)(540)

Description Two component acrylic filler with excellent filling properties. 2K Hi-Build Acryl Filler 5:1 can be used instead of spray putty that provides shorter repair process and less material consumption.

Application For treatment of large areas recoated with polyester materials.

Characteristics• Excellent filling properties• Due to its good flow, the product is easy to sand even when applied in 2 – 4 coats• Does not drip even when applied with a spray gun with a 2.5 mm nozzle • Sanding by hand or dry-sanding by machine

SubstratesAll kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings.

2К Hi-Build Acryl Filler 5:1


5:1 by volume with Hardener for 2КAcrylic Filler Hi-Build 5:1

Viscosity: 48 – 52 sec, FORD 4 (+20°С)

Pot life: ca. 45 min at 20°C

Air drying (at +20°C ambient temperature) is not recommended

- Flash-off: 10 min- Through-drying: 45 min at 60°C or

Color greyDensity 1530 g/LFlash point 23°C

Xn

Harmful

- Flash-off: 10 min- Medium wave or short wave infrared drying: 12 – 15 min


Application*

Further treatment

Technical data

Safety information

1.8 – 2.5 mm / see spray gun manufacturer’s instruction

2 – 4 normal coats 80 – 100 μm dry film thickness per one coat

Dry sanding: with P360 – 500

Recoat with all conventional (solvent-borne) refinishing materials

BLACK LABEL SERIES

11catalogue 2014

BLACK LABEL SERIES


7-400-1500 1 L, Clearcoat + 0.5 L hardener 12

7-400-5000 5 L, Clearcoat 4

7-435-2500 2.5 L, Hardener 4

7-436-2500 2.5 L, Slow Hardener 4

7-437-2500 2.5 L, Fast Hardener 4

Description 2К Ultra HS Clearcoat is a two-component high-gloss clearcoat for car refinishing with conventional and waterborne paint materials.

Application For two-coat paintworks in car and commercial vehicle refinishing.

Characteristics• Scratch resistance• Very good flow• UV resistance• Optimized for application in spray booths and preparation zones.

SubstratesWaterborne and solventborne basecoats, OEM coatings.

2:1 with Hardener for 2K Ultra HS Clearcoat

15 – 17 sec, FORD 4 (+20°С)

Pot life: up to 2 h at 20°C

- Flash-off: 7 – 10 min- 30 min at 60°C

- Drying: 6 – 7 h at 20°C- Polishing: after 10 – 11 h at 20°C- Full curing: 5 – 7 days or

Short wave/medium wave infrared drying: 10 min

Xn

Density ca. 1000 g/lFlash point 23°C

Application

Further treatment

Technical data

Safety information

1.2 mm / see spray gun manufacturer’s instructions

2 full coats = 50 – 55 μm dry film thickness

2K Ultra HS Clearcoat

Harmful

12catalogue 2014

Silicone remover “Strawberry”


7-550-1000 1 L 12

7-550-5000 5 L 4

VOC: 765 g/LEU limit value: 2004/42/IIB(a)(850)

Description Strawberry scented cleaning agent based on volatile organic solvents for initial cleaning of old/OEM coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product.

Application Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish.

SubstratesMetal and plastic parts, polyester putties, primers, fillers, fully cured old or fresh coatings.

technical dataDensity 765 g/LFlash point < 21°C

Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings

– Clean the substrate with CF Silicone Remover “Strawberry”– Apply with a spray gun, a cloth or a sponge


Application

Harmful Highly flammable Dangerous for the environment

Xn F N

Pigment Paste blackPigment paste for 1К and 2К acrylic fillers based on organic solvents. Addition of the paste has no impact on hardener application process.

Depending on the added amount of paste (1-5% by weight hardener), coatings with different shades of grey can be obtained.

technical dataColor blackDensity 1100-1200 g/LFlash point 27°C


4-330-0501 500 ml 30

See TDS of the respective material Add 1 – 5% hardener by weight

Application

– Do not allow to dry on the substrate being treated– Remove any remaining residue with a cleaning cloth

Safety information

BLACK LABEL SERIES

13catalogue 2014

BLACK LABEL SERIES

Prepare the surface according to main material application instructions

While applying a filler, use the following mixing ratio:- filler 100%vol.- hardener 25%vol.- accelerator max. 18%vol.

While applying a clearcoat, use the following mixing ratio:- clearcoat 100%vol.- hardener 50%vol.- accelerator max. 8%vol.

Do not use fast and extra fast hardeners while mixing accelerator with clear coats as it will lead to opacity and coat adhesion decrease.

Apply according to main material application instructions.

See main material application instructions.

Toxic

Density 900 g/lFlash point 24°C

Application*

Further treatment

Technical data

Safety information

Accelerator


7-830-1000 1 L 12

Description Special additive for accelerating the drying of two-component (2К) fillers and clearcoats. In case of clearcoats, the accelerator is to be used with standard and slow hardeners. The product saves approx. 15% of drying time.

SubstratesWaterborne and solvent born basecoats, OEM coatings.

14catalogue 2014



Application*

Further treatment

Technical data

Storage

Safety information

Color yellowDensity 1760 g/LFlash point 31°C





With P80 – 180



Harmful


CF Multi Putty


2-210-2000 2 kg, w/hardener 10

Description Two component multifunctional fine-grained polyester putty for filling unevenness especially on aluminum and galvanized surfaces.

Application Multifunctional finishing putty for eliminating car and commercial vehicle body imperfections.

Characteristics• It is characterized by easily work in thick and thin layers • It can also be used as finishing putty • After drying it produces a smooth, pin-hole free surface • Does not clog the sandpaper • Intended for manual/machine dry sanding.

SubstratesSteel, galvanized surfaces, aluminum, fiberglass plastics, polyester materials, OEM substrates*.

PUTTIES

15catalogue 2014

PUTTIES


Application*

Further treatment

Technical data

Storage

Safety information

Color yellowDensity 1900 g/LFlash point 31°C





With P80 – 180



Xn

Harmful


Soft Putty


2-120-0500 0.5 kg, w/hardener 24

2-120-1000 1 kg, w/hardener 12

2-120-1800 1.8 kg, w/hardener 10

Description Two component polyester putty Soft is extremely easy to apply and adopts any desired shape regardless of the material coat thickness. Perfect solution for eliminating car and commercial vehicle body imperfections.

Application For eliminating car and commercial vehicle body imperfections.

Characteristics• Suitable for dry sanding by machine or by hand• Optimal viscosity/plasticity ratio ensures uniform material application • Fast drying prevents clogging of the sandpaper.

SubstratesAll kinds of steel, fibers plastics, OEM substrates*.

16catalogue 2014


Glass Putty


2-140-0500 0.5 kg, w/hardener 24

2-140-1000 1 kg, w/hardener 12

2-140-1800 1.8 kg, w/hardener 10

Description Two component fiberglass-filled putty. Once dry fiberglass makes the putty highly durable. The product has an excellent adhesion to sanded metal. The putty is used in car and commercial vehicle repair for filling cracks, small holes and areas damaged by corrosion.

Application Fiberglass putty for eliminating car and commercial vehicle body imperfections.

Characteristics• High stability• Limited sanding.

SubstratesAll kinds of steel, aluminium, fiberglass plastics.





With P80 – 180



Xn

Harmful

Color greenDensity 1800 g/LFlash point 31°C


Application*

Further treatment

Technical data

Storage

Safety information

PUTTIES

17catalogue 2014

PUTTIES

Plastic Putty


2-160-0500 0.5 kg, w/hardener 24


Description Two component high-plasticity polyester putty for plastic parts repair. Excellent adhesion to plastics, fast drying and easy sanding.

Application For repairs on plastic parts of cars and commercial vehicles.

SubstratesAll kinds of plastic:– ABS (acrylonitrile-butadiene-styrene copolymer)– EP (epoxides/laminates)– PA (polyamide)– PBTP (polybutylene terephtalate)– PC (polycarbonate)– POM (polyoxymethylene)– PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer)– PPO (polypropylene oxide)– PUR (polyurethane) soft and hard – PVC (polyvinyl chloride).

Substrates to be treated must be cleaned, dried, degreased (e. g. with CF Silicone Remover) and treated with suitable matting materials




With P80 – 180



Application*

Further treatment


Xn

Harmful


Technical data

Storage

Safety information

• Substrate to be treated must be thoroughly cleaned, degreased and dried• Prior to putty application, the substrate must be sanded/treated with matting abrasives.

Remove all old materials that have poor adhesion or have not fully dried.• Do not apply this product on thermoplastic coatings or etch/acid primers• Prior to application, mix well with a hardener/catalyst• Apply at a temperature no lower than +10°C.

18catalogue 2014

PUTTIES


• Do not apply on etch primers, epoxy primers and fillers• If necessary, use only waterborne epoxy primers

• Add 3.5% CHP Hardener for Spray Putty• Mix well prior to application

Viscosity as supplied = application viscosity (RFU)

3 – 5 h at 18 – 20°C or

30 min at 60°C or15 min at 80°C


Xn

Harmful



Application*

Further treatment

Technical data

Storage

Safety information


Spray Putty


2-250-1200 1.2 kg, w/hardener 6

Description Two component polyester putty for filling surface irregularities, sanding marks and pinholes on car and commercial vehicle body parts as well as on vehicle structural components.Good adhesion to metals, wood, polyester materials and fiberglass plastics.Spray Putty is suitable for leveling small and big surface irregularities. The material dries quickly and creates a smooth pinhole-free surface.In order to achieve a high-quality finish coating, Spray Putty can be covered with a thin (~ 35 μm) sealing coat of 2К acrylic or 2К epoxy fillers without subsequent sanding.

Application For leveling small and big surface irregularities of car and commercial vehicle bodies.

SubstratesMetal surfaces, polyester putties, fiberglass, wood.

20 – 30 min at 18 – 20°C

2.0 – 2.5 mm / see spray gun manufacturer’s instructions

With P120 – 320

In order to isolate the substrate and prevent the formation of air bubbles (esp. in high humidity), apply 2К acrylic fillers 4:1, 5:1

19catalogue 2014

2K HS Clearcoat 2:1 SCrAtCH reSiStAnt


7-220-1500 1 L Clearcoat + 0.5 L Standart Hardener 12

7-220-5000 5 L Clearcoat 4

7-320-2500 2.5 L Standart Hardener 4

7-321-2500 2.5 L Slow Hardener 4

7-322-2500 2.5 L Fast Hardener 4

VOC: 535 g/LEU limit value: 2004/42/IIB(e)(840)

Description Two component High Solid gloss clearcoat for partial or complete automotive two-coat paintworks.

Application For two-coat paintworks in car and commercial vehicle refinishing. Suitable for applications in spray booths and preparation areas.

Characteristics• High scratch resistance• Suitable for application on solvent- and waterborne base coats• Good flow • High mechanical durability • UV-resistance / non-yellowing • Good chemical, mechanical and weathering resistance

SubstratesWaterborne and solvent-borne basecoats, OEM coatings.

CLEARCOATS

2:1 with hardener for 2K HS Clearcoat 2:1

15 – 17 sec, FORD 4 (+20°С)

Pot life: up to 2 hours at 20°C

1.2 mm / see spray gun manufacturer’s instructions

2 normal coats = 50 – 55 μm dry film thickness10 min flash-off between the coats

- Flash-off: 5 – 7 min- 30 min at 60°C or

- Dry through: 6 – 7 hours at 20°C- Polishing: after 10 – 11 hours at 20°C- Full curing: 5 – 7 days

Short and Medium wave: 10 min

Application

Further treatment

Technical data

Safety information

Harmful

Density ca 1000 g/l (clearcoat)Flash point 23°C

Xn

20catalogue 2014



2K MS Clearcoat 2:1 inDUStriAL USe


7-150-1500 1 L Clearcoat + 0.5 L Standart Hardener 12

7-150-5000 5 L Clearcoat 4

7-350-2500 2.5 L Standart Hardener 4

7-351-2500 2.5 L Slow Hardener 4

7-352-2500 2.5 L Fast Hardener 4

Description Two-component Medium Solid gloss acrylic clearcoat for two-coat finishes in partial and complete vehicle refinish.

Application For two-coat industrial paintworks.

Characteristics• Special finish for industrial use • Suitable for application on solvent- and waterborne base coats• Good flow • High mechanical durability • UV-resistance / non-yellowing • Good chemical, mechanical and weathering resistance


2:1 with hardener for 2K MS Clearcoat 2:1

14 – 16 sec, FORD 4 (+20°С)

Pot life: up to 1.5 hours at 20°C

1.2 – 1.3 mm / see spray gun manufacturer’s instructions10 min flash-off between the coats

2 normal coats = 40 – 45 μm dry film thickness

- Flash-off: 5 – 10 min- 30 min at 60°C or

- Dry through: 5 – 7 hours at 20°C- Polishing: after 9 – 10 hours at 20°C- Full curing: 5 – 7 days

Short and Medium wave: 10 min

Application

Further treatment

Technical data

Safety information

Harmful

Density 960 g/l (clearcoat)Flash point 23°C

Xn

CLEARCOATS

21catalogue 2014

CLEARCOATS

2K UHS Clearсoat


7-115-1000 1 L Clearcoat 127-115-5000 5 L Clearcoat 47-315-0500 500 ml Standard Hardener 127-315-2500 2.5 L Standard Hardener 47-317-0500 500 ml Fast Hardener 127-317-2500 2.5 L Fast Hardener 4

VOC 420 g/LEU limit value: 2004/42/IIB(d)(420)

Description Two component Ultra High Solid gloss clearcoat for partial or complete automotive two-coat paintworks.

Application For two-coat paintworks in car and commercial vehicle refinishing.

Characteristics• Easy application • Excellent flow • Deep gloss • High mechanical durability• Yellowing resistance • Can be polished in 60 minutes after cooling.


14 – 16 sec, FORD 4 (+20°С)

Pot life: 30 – 60 min at 20°C

• Ready for use products are applied at a temperature higher than 15°C• Too thick layers can have negative influence to drying time and level of gloss

1.2 – 1.3 mm / see spray gun manufacturer’s instructions10 min flash-off between the coats

1.5 – 2 normal coats = 50 – 60 μm dry film thickness

- Flash-off: 10 minwith fast hardener: 25 min at 60°Cwith standard hardener: 30 min at 60°Ccan be polished: 60 min after cooling or

- Full curing: 14 – 18 hours at 20°C

2:1 with Hardener for 2K UHS Clearcoat + 0-5% CF Universal thinner

Application

Further treatment

Technical data

Safety information

Harmful

Density ca 1080 g/l (clearcoat)Flash point 24°C

Xn

22catalogue 2014


Application

Further treatment

Technical data

Safety information

Thoroughly clean and degrease surfaces with CF Silicone Remover. Sand old finish coating wet or dry with P800-P1000 abrasive. Clean and degrease surfaces with CF Silicone Remover once more.

Apply basecoats according to the technical data sheet.

Apply the clearcoat within 20 min after application of the base coat

Shake can thoroughly before use at least for 2 minutes.

Apply 1-2 normal, even coatsAllow 5-10 minutes flash-off time between coats

Allow 30 minutes before handling

Xi

Density ca 900 g/lFlash point -40°C

This is a pressurized container, do not expose to direct sunlight or store above 50°C.

VOC 710 g/LEU limit value: 2004/42/IIB(e)(840)

1K Acryl Clearcoat Spray


7-210-0500 500 ml 6

Description One component gloss clearcoat for spot repair of automotive two-coat paintworks.

Application For two-coat paintworks in car refinishing.

Characteristics• Easy application• Fast drying• Very high gloss finish• Excellent UV resistance• Blends easily with existing 2K clear coating• High performance clog-free aerosol can.


CLEARCOATS

Drying time depends on film thickness, air humidity and temperature.

Irrirating Extremely flammable

F

23catalogue 2014

Substrates to be treated must be cleaned, dried, degreased (e. g. with CF Silicone Remover) and treated with suitable matting materials

12 – 15 sec at 20°C, RFU


1 coat = 3 – 5 μm

Ambient conditions:- temperature: no lower than +10°С- relative humidity: no more than 75%

10 min at 20°C


Xn

Harmful

Color colorless, with metallicDensity 894 g/LFlash point 10°C

F


4-350-1000 1 L 12


Description One component transparent primer for almost all kinds of plastic, designed to improve the adhesion of refinishing materials to the substrate.

Application For priming plastic parts prior to application of subsequent materials in car and commercial vehicle refinishing.

CharacteristicsContains a metallic pigment for controlling the process of application.

SubstratesABS (acrylonitrile-butadiene-styrene copolymer), EP (epoxides/laminates), PA (polyamide), PBTP (polybutylene terephtalate), PC (polycarbonate), POM (polyoxymethylene), PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer), PPO (polypropylene oxide), PUR (polyurethane) soft and hard, PVC (polyvinyl chloride), OEM coatings.

PRIMERS, FILLERS


Application

Further treatment

Technical data

Storage

Safety information

Recoat with 2К Plastic Filler and top coat

Highly flammable

1K Plastic Primer

24catalogue 2014


Plastic Primer Spray


7-355-0500 500 ml 6

Description 1K ready for use adhesion promoter in an aerosol can. The plastic primer improves the adhesion of paint, adhesives or sealants to the most of car plastics.


Characteristics• Easy application• Fast drying• May be overpainted with the most of paint systems• High performance clog-free aerosol can.

SubstratesMost of plastics, polyester bodyfiller, sand G.R.P, old/original paintworks


Application*

Further treatment

Technical data

Storage

Safety information

Color colorlessDensity 900 g/LFlash point -40°C

Thoroughly clean and degrease surfaces with CF Silicone Remover.

Shake can thoroughly before use at least for 2 minutes.

Apply 2 thin even coats from a distance of 20-30 cm.

Before overcoats allow:- 30 min at 20°C or - 15 min at 60°C.


Overpaints with proper primer/filler or/and topcoat after drying.


Xi


F

PRIMERS, FILLERS

25catalogue 2014

PRIMERS, FILLERS

Hi-Build Filler Spray


4-310-0500 500 ml 6


Description 1K ready for use high build filler in an aerosol can. Used for priming uneven surfaces before top coating. Filler is capable of producing a coating film thickness similar to that of a spray gun applied primer.


Characteristics• Easy application• Fast drying• May be overpainted with the most of paint systems• High performance clog-free aerosol can.

SubstratesMost plastics, polyester bodyfiller, sand G.R.P, old/original paintworks


Application*

Further treatment

Technical data

Storage

Safety information

Density 900 g/LFlash point -40°C

Thoroughly clean and degrease surfaces with CF Silicone Remover.

Shake can thoroughly before use for a minimum of 2 minutes.

Apply 2 thin even coats from a distance of 20-30 cm.

Before overcoats allow: - 30 min at 20°C or - 15 min at 60°C.


Overpaints with proper primer/filler or/and topcoat after drying.


Xi


F

26catalogue 2014

PRIMERS, FILLERS

Pot life: up to 60 min at 20°C


1 – 3 normal coats = 60 – 240 μm

With P360 – 500

Recoat with all conventional (solventborne) refinishing materials


4:1 by volume with Hardener for 2К HS Acrylic Filler 4:1

25 – 35 sec, FORD 4 (at +20°С)

Color greyDensity 1550 g/LFlash point > 23°C

Xn

Harmful

5 – 15% CF Universal Thinner

- Dust-free: 30 min- Through-drying: 3 – 5 h at 20°C or

- Flash-off: 10 min at 20°C- Through-drying: 20 – 30 min at 60°C or

- Flash-off: 10 min at 20°C - Medium wave or short wave infrared drying:

12 – 15 min


Application

Further treatment

Technical data

Safety information

VOC: 490 g/LEU limit value: 2004/42/IIB(c)(540)

2К HS Acryl Filler 4:1 grey


4-100-0800 0.8 L Filler + 0.2 L Hardener 12

4-101-0800 0.8 L Filler Black+ 0.2 L Hardener 12

4-200-3600 3.6 L Filler 2

4-201-3600 3.6 L Filler Black 2

4-210-0900 Hardener for filler 900 ml 12

Description Two component acrylic high-solid filler for vehicle refinishing with conventional (solventborne) materials. The product is applied on clean steel, aluminium and galvanized substrates (after pre-treatment with an etch primer), OEM / cataphoresis primers and polyester putties.

Application For sealing body parts of cars and commercial vehicles.

Characteristics• Very good filling properties• Fast drying• Wet and dry sanding


27catalogue 2014


6:1 by volume with Hardener for 2K Acryl Filler Wet-on-Wet

5 – 15% CF Universal Thinner

1 full coat = 30 – 40 μm

- Flash-off: 5 – 7 min- Recoatable: after 15 – 20 min at 20°C

2 – 3 full coats = 60 – 110 μm

- Flash-off: 10 min at 20°C- Through-drying: 20 min at 60°C

Color greyDensity 1390 g/LFlash point > 23°C

- Flash-off between coats: 5 – 7 min- Sanding: after 3 – 4 h at 20°C or


Application

Further wet-on-wet treatment

Technical data

Further treatment with intermediate sanding

Safety informationXn

Pot life: ca. 60 min at 20°C



With P360 – 500


2K Acryl Filler wet-on-wet


4-300-1050 0.9 L filler + 0.15 L hardener 12

VOC: 540 g/LEU limit value: 2004/42/IIB(c)(540)

Description Acrylic filler 6:1 is used in the repair of damaged and new body parts. The product is applied wet on wet or as a sandable filler. Once the filler has dried completely, it can be wet or dry sanded manually or by machine. This method is suitable for application of polyester putties to repair small or medium damages. When applied wet on wet, the filler efficiently seals the surface to be painted without intermediate drying and sanding.

Application For the repair of damaged and new body parts by application wet on wet or with sanding.

Characteristics• Very good sealing properties• Suitable for all kinds of organic solvent-based paintworks• Very good filling properties• Very fast drying.


Harmful

PRIMERS, FILLERS

28catalogue 2014

Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings

– Clean the substrate with CF Silicone Remover – Apply with a spray gun, a cloth or a sponge

– Do not allow to dry on the substrate being treated– Remove any remaining residue with a cleaning cloth


Application

Harmful Dangerous for the environment

Xn N

Safety information

Highly flammable

F


Application

Safety information


See TDS of the principal material

Xn

Harmful

Universal thinner


7-600-1000 1 L 12

7-600-5000 5 L 4

Description Product for thinning all kinds of C.A.R.FIT refinishing materials.

Application Thinning of primers, fillers and clear coats in car and commercial vehicle refinishing.


technical dataDensity 900 g/LFlash point 24°C

THINNERS, CLEANERS

Silicone remover


7-500-1000 1 L 12

7-500-5000 5 L 4

VOC: 765 g/LEU limit value: 2004/42/IIB(a)(850)

Description Cleaning compound based on volatile organic solvents for initial cleaning of old/OEM coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product.

Application Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish.


technical dataDensity 765 g/LFlash point < 21°C

29catalogue 2014


Fade out Spray


7-555-0500 500 ml 6


Description Fade Out Spray is a special thinner for fast, simple, accurate dissolving of edges of 2K Clearcoat repairs.It increases efficiency of the fade out process to give an invisible blend. Using this product in partial coating repair provides a result of a smooth fade out between old and new coatings.

Application For paintwork repair in car refinishing.

Characteristics• Easy application• Fast drying• Ideal for use with both MS and HS Clearcoat• UV stable• High performance clog-free aerosol can.

SubstratesRefinish clearcoats, old/original and OEM paintworks.

THINNERS, CLEANERS


Application*

Further treatment

Technical data

Storage

Safety information

Color colorlessDensity ca 800 g/lFlash point -40°C

Apply base coat and then clearcoat according to TDS.

Shake can thoroughly before use for a minimum of 2 minutes.

Once the clearcoat has been applied a light mist coat Fade Out Spray is applied over the blend area holding the aerosol 25cm from the panel.

The blending process is best undertaken in two rapid light passes of the aerosol. The blend edge will melt into the original paintwork requiring little or no processing once the clear coat has cured.

Fade Out Spray is used when blends or spot repairs operations are being carried out; all these processes result in an interface being created between the existing, curedcoating and the freshly applied clear coat.If the interface is not treated a dry edge will be visible upon cure of the fresh coating.

Once applied the clearcoat manufacturer’s instructions for flash off and air/force dry should be followed.


Xn

Harmful Extremely flammable

F

30catalogue 2014

Stone Chip Protection


5-600-1000 1 L bottle, black 12

5-601-1000 1 L bottle, grey 12

Description Synthetic resin-based stone chip protection of vehicle underbody and lower body. The coating can be primed or overpainted in any color within 30-40 minutes after drying. The coating has high durability and excellent resistance to abrasive wear. It also has sound deadening and vibration absorbing properties. Application For treatment of car and commercial vehicle bodies.

Characteristics• Supplied in a bottle – always ready for use • Recoatable• Produces a durable coating that is resistant to abrasive wear and aggressive chemicals • Sound deadening and vibration absorbing properties.

SubstratesVarious metal surfaces, primed metal parts, old/OEM coatings.

BODYCOATS, CABIN COATS

Clean the substrate with CF Silicone Remover

– Shake well before use for about 3 min– Do not apply on engine, brake system and exhaust pipe

Apply several coats with a sprayer at a spray pressure of 4 – 5 bar

– tack-free: 1.5 h– recoating: after 1 h

Harmful

Highly flammable


Application

Technical data

Safety information

Color black / greyDensity 1400 g/LFlash point < 21°C

Xn

F

VOC: 350–360 g/LEU limit value: 2004/42/IIB(e)(840)

31catalogue 2014

Do not apply on walls that have already been exposed to overspray and other materials

Viscosity as supplied = application viscosity (RFU)


1 – 2 coats = 75 – 95 μm or

Apply a uniform thin coat with a brush or

Color transparentDensity 1024 g/lCoverage 8-10 m2/l

Store in a cool dry place protected from freezing

Remove with a sponge and water


Application

Further treatment

Technical data

Storage

Safety information

Apply a uniform thin coat with a roller or

Refer for consultation of airless spray equipment manufacturer

Depends on the coat thickness of the material being applied. For best results, we recommend to apply the material in 1-2 coats with a 20 min flash-off between the coats. Two coats ensure durable protection with no risk of the coating being washed away.

All tools used for the application of the coating must be thoroughly washed with water.If the temperature inside the spray booth is 70 – 90°C, the coating should be renewed more often: at least once a month. This will prevent the protective film from drying up.If necessary, several new layers can be applied on the old film.In case of a long operation life of the spray booth, it is recommended that the old protective film should be removed prior to application of a new one.

tack Coating for Spray Booth


3-401-0010 10 L 1

Description Booth mask safely binds paint, dust and overspray particles that tend to settle on spray booth walls and ceiling panels, thus preventing contamination of the surface being refinished. The compound stays transparent and water-soluble. Thin and sticky protective film never dries out on the wall, ensuring safe dust and overspray binding. Once the film loses its particle-binding capacity, it can be easily washed off with water and a sponge and then reapplied.

Application For overspray and dust protection of spray booth walls.

Characteristics• Provides dust protection of the object being refinished• Protects spray booth surfaces from paint, dust and overspray• Specially designed to protect glass and lights without impacting light permeability and reflection capacity. • Easy to apply and remove • Very cost-effective. Depending on the level of contamination, the coating should be replenished once in a

few weeks. • 100% environmentally-friendly.

SubstratesAluminium, steel and galvanized walls of spray booth cabins; fully cured and clean paintworks.

BODYCOATS, CABIN COATS

Removal

Contains no harmful or life-threatening components. Can be disposed of as harmless waste in accordance with the local legislation.

tACKy CoAt

32catalogue 2014


Application

Technical data

Storage

Safety information

Clean and degrease surfaces with solvent like acetone. Oxidized metal surfaces and concrete must be first sanded and then cleaned. Degrease PVC, aluminum and glass with a non greasy solvent, like acetone.

• The temperature of the substrate must be within +5…+30°C• In case of application by cold weather, store the cartridges at 20°C before use• Prior to application, carry out a test on adhesion efficiency and compatibility with each of the materials

upon which the sealant will be applied

Puncture the cartridge and section the nozzle according to the extrusion diameter required, remove the metal base and the dehydrating salts and extrude from cartridge with a manual or pneumatic gun.

Film thickness depends on the characteristics of the materials being bonded.The joint should be overlapped on the previous section; the end-to-end jointis prohibited to avoid the leakage of water.The process of bonding must take no more than 10 minutes.PU sealant has a relatively high viscosity. Therefore, it is advisable to use special clamps for locking the parts being bonded until the sealant dries completely.

Tack free time: 60 min at 23°C and 50% r.h.Cure rate: 4 mm / 24 hrs at 23°C and 50% r.h.

Color black greyDensity 1150±50 g/l 1180±50 g/lFlash point 40° ÷ 55°C 40° ÷ 55°CHardness Shore A (ISO 868-3 s) approx. 45 approx. 45Elongation at break (ISO 37) > 600% > 600%Tensile at 100% elongation (ISO 37) 0.6 MPa 0.6 MPaTemperature resistance -40° ÷ +90°C -40° ÷ +90°C

Store in cool dry place and at temperature < 25°C, avoid sunlight

Xn

Harmful

VOC (grey and black): 7%EU limit value: 2004/42/IIB(e)(840)

PU Adhesive and Sealant


5-112-0310 310 ml tube, grey 12

5-114-0310 310 ml tube, black 12

Description PU Adhesive and Sealant is a one-component polyurethane sealant. By reaction with air humidity, the product cures into a strong but flexible rubber, with excellent adhesion to many substrates. It will not sag even when applied in thick layers. The product is resistant to ageing, weather and is impermeable to water.

Application PU Adhesive and Sealant is suitable for sealing all kinds of joints: overlaps, flanges, linear-weldings, spotweldings etc. It is also used to seal drains, lamp housings, reversible roofs and other car body parts.

Characteristics• Excellent adhesion to most rough and treated metal sheet• Once fully cured* the sealer can be recoated with any two component paint materials.

*preliminary tests are recommended prior to application of resin-based paints.

SubstratesVarious metal surfaces, e. g. aluminium, wood, primed substrates, thermoreactive plastic, old/OEM coatings.

SEALANTS

33catalogue 2014

SEALANTS

Clean and degrease surfaces with solvent like acetone. Let dry after degreasing.

• The substrates to be bonded must be dry, oil-free, grease-free, dust-free and free of any contaminating agents that could harm bonding.

• In cold weather, store the cartridges or sausages at a temperature of about 20°C before use.• Do not wipe the substrate up and down. If the pad has got dirty, replace it with a new one and

continue the procedure. If the primer peels off, replace the windshield to avoid unpredictable consequences.

• If any deviations in the substrate material are detected, it is advisable to carry out an adhesion test prior to actual bonding. Test bonding of the windshield with any materials is particularly recommended to achieve desirable adhesion.

• Avoid any contact with non-cured MS, hybrid PU or silicone sealants as well as with alcohols or ammonia during curing.


Application Apply the glass coated with the sealant on the car body and press, before the skin formation time (i.e. within 30 minutes).Apply the glue with a glue gun onto the substrate.Install the glass onto the window frame and use the palm to press softly till the glass is bound flatly. Adjust the space up and down, left and right, and use the press sensitive tape to fix.

Do not apply at a temperature below +5°C.

Excessive glue can be removed with a scraper or soapy water.If any glue residue remains on the substrate, quickly remove it with an alcohol-free cleaning agent, e. g. gasoline. If the glue has hardened, use a blade.

Tack free time: 40 – 60 min at 23°C and 50% r.h.Cure rate: > 3.5 mm / 24 hrs at 23°C and 50% r.hDrive-away time at 23°C and 50% r.h.:- 6 hrs. no airbag- 8 hrs. with airbag

Store in cool dry place and at temperature < 25°C, avoid sunlight

Xn

Harmful

Color blackDensity 1190 g/lFlash point > 50°CHardness Shore A (ISO 868-3 s) > 55

Technical data

Storage

Safety information

windglass Glue


5-131-0310 310 ml tube, black 12

Description Windglass Glue is a one component, high viscosity, moisture curing polyurethane adhesive, primarily used for automotive direct glazing with and without airbag. It cures in a longer time allowing application on big windscreens such as buses and trucks.

Application Windscreen direct glazing.

Characteristics• Does not drip when used on vertical surfaces• Flexibility, excellence curing• Prevents metal corrosion and penetration of contaminants into the vehicle• Prevents yellowing• The cured product forms a durable glue film.

SubstratesVarious metal surfaces, incl. glass, aluminum , ceramic coatings, old/OEM coatings.

Shear strength (Ford SAE J 1529) > 3.5 MPaElongation at break (ISO 37) > 700%Tensile strength (ISO 37) > 6 MPa

VOC (grey and black): 3%EU limit value: 2004/42/IIB(e)(840)

34catalogue 2014

rubbing Compound


5-100-0500 500 ml 6

Description Polishing paste without silicone for removing sanding marks left on fresh and old coatings by manual or machine sanding with P1500-2000 grit abrasives.

Application Polishing of car and truck coatings.

Characteristics

SubstratesOld/OEM or fully cured fresh refinishing coatings.

ANCILLARY MATERIALS

The substrate must be thoroughly cleaned of dust using a sponge with water and degreased with degreasing compounds.

1. Fresh and fully cured paintworksUse a woolen polishing pad.Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result.After manual sanding with abrasive paper, especially on dark surfaces, repeated polishing may be necessary.Once almost all the paste has been used up, increase the RPM of the sander for better clean-ing of the surface.For higher shine and deeper color, repeat the operation with a yellow foam polishing pad until complete removal of fine scratches left by the woolen polishing pad.

2. old paintworksUse a foam polishing pad.Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result.Once almost all the paste has been used up, increase the RPM of the sander for better clean-ing of the surface.

• Apply the product onto the surface, not the polishing pad!• Mask plastic parts in advance to avoid their contamination• Avoid overheating of the surface• A few minutes after polishing, remove the compound residue with a microfiber cloth.


Application

Technical data

Storage

Abrasive aluminium oxideConsumption 50-60 ml/m2

35catalogue 2014

Masking tape


9-100-0019 width 19 mm, 80°С 48

9-100-0025 width 25 mm, 80°С 36

9-100-0038 width 38 mm, 80°С 24

9-100-0050 width 50 mm, 80°С 18


1-200-3820 3.8 m х 200 m, roll 1

1-200-0450 4 m х 5 m, folded 40

1-200-0470 4 m х 7 m, folded 40

Masking Film electrostatic effect

MASKING

Description Semi-transparent polyethylene masking film has good adhesion to refinishing coatings due to its electrostatic charge and is highly resistant to weathering.

Application For quick masking of large vehicle surfaces and parts prior to painting.

SubstratesMetal and plastic parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings.

technical Data

Size 3.8 m x 200 m 4 m х 7 m 4 m x 5 m

Thickness 9 μm 7 μm 7 μm

Material HDPE (High Density Polyethylene)

Heat resistance 10…140°С

Static treatment + Corona treatment 44 dyne/cm

Backing material impregnated crepe paper

Thickness 90 ± 15 μm

Tensile strength 50 ± 15 N/mm2

Elongation at break 9 ± 2 %

Description Slightly creped masking tape with excellent elongation characteristics and high initial adhesion strength. The product is suitable for masking jobs for sanding as well as for application of waterborne or solventborne refinishing materials with subsequent drying in a spray booth.Once the refinishing coating has dried, the masking tape comes off cleanly and leaves no residue.

Application Professional masking tape for secure vehicle body protection from overspray during refinishing with subsequent drying in a spray booth at a temperature of 60°С.

SubstratesMetal parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings.

technical Data

Adhesive material natural rubber

Adhesion 4.5 ± 1 N/25 mm

Tack (Rolling Ball Tack)

< 3 cm

36catalogue 2014

Pretaped Masking FilmsPolyethylene masking film with an adhesive tape for refinishing works. It prevents overspray from getting onto the surface being treated. The masking film is highly-durable and adheres well to the surface.

Classic Foam Masking tapes classic Classic foam tape for masking gaps and apertures in the vicinity of doors, bonnet, trunk and gas cap lid. The masking tape helps avoid sharp edges in painting and prevents overspray from getting inside the vehicle. The tape is dust and paint-proof that makes the use of passenger compartment protection unnecessary.

Protective Film for Steering wheelTransparent tape for vehicle steering wheel protection during repair. Supplied in roll, without dispenser.


3-110-0150 150 m, roll 1

3-140-0001 dispenser for steering wheel protective film, length 125 mm

1


9-109-0500 13 mm х 50 m, roll 1

9-109-0350 19 mm х 35 m, roll 1


1-200-0550 550 mm х 33 m, roll 1

1-200-1800 1800 mm х 33 m, roll 1

1-200-2700 2700 mm х 20 m, roll 1

MASKING

37catalogue 2014

MASKING

Seat CoversPre-cut polyethylene seat cover for masking vehicle seats during repair. Supplied in perforated rolls for easy tear-off.


3-120-0500 size: 82 cm x 130 cm x 10 μm 500

Disposable Floor MatsDisposable auto floor mat designed to protect the floor of the vehicle from dirt during repair and maintenance.

Polyethylene Car CoverPolyethylene cover specially designed to protect freshly painted and damaged cars as well as car assemblies, aggregates and parts during inspection/handover. Cover edge is outfitted with an elastic band for secure masking. Suitable for indoor and outdoor use. Reusable.


3-100-0500 size: 38 cm x 50 cm 500


3-150-0020 size L, 7.5 m x 4.8 m x 30 μm 20

38catalogue 2014

MASKING

tire BagsHandy bags made of semi-transparent polyethylene for seasonal tire storage. The bags are fitted with a tag displaying the customer’s name and wheel size for quick identification.


3-130-3010 size: 70 cm x 30 cm x 100 cm 100

39catalogue 2014

Car Clean MultiLint-free cloths (w/o dispenser) with a high resistance to oils and solvents for the removal of spilled oil, paint, ink, etc.

Characteristics• Special impregnation for higher absorption capacity• High absorption capacity enables the cloth to absorb 8 times its own weight in liquid• Suitable for cleaning and wiping of equipment, floors, workpieces, etc.• Durable and soft at the same time• Material density: 75 g/m2

Double Layer Cleaning ClothsHighly durable double-layer lint-free cleaning cloths made of quality embossed crepe paper. Supplied in perforated rolls. Material density: 2x2.22 g/m2

Microfibre Cleaning ClothWoven microfiber cloth for fast and efficient cleaning of the surface without using cleaning agents.

Characteristics• Captures and binds contaminants in a fast and efficient way • Restores the gloss and color of the paintwork • Does not require cleaning agents – cost saving • Reusable after washing• Material density: 300 g/m2


8-801-0500 380 mm х 320 mm, rolls 500

8-801-0050 420 mm х 267 mm 50


8-803-0002 400 mm х 400 mm, folded 1


8-802-1000 380 mm х 370 mm, rolls 1000

CLOTHS

40catalogue 2014

CLOTHS

nonwoven Polishing ClothSoft lint-free polishing cloth made of synthetic nonwoven fabric for the manual polishing of new and old coatings.

tack ClothCotton tack cloth for cleaning dust from all kinds of surfaces, including water-based coatings. Does not wrinkle – no need in smoothing out the fabric. Wax and silicone-free.

tack Cloth “Super wave”DescriptionTack cloth “Super Wave” easily adopts palm shape, due to which it fits tightly against the surface upon wiping – no need in supplementary devices. Larger area of the surface and, at the same time, a smaller contact zone allow for secure dust binding inside the cloth, regardless of the size of dust particles. The carrier material lets dust easily enter into the inner layers and provides additional security and the highest possible dust absorption capacity.The impregnation of the cloth does not dry out and is compatible with all kinds of refinishing materials.ApplicationFor dust binding for dust-free sanding and refinishing.Characteristics• Wavelike surface is hugely important for removing dust from large and even parts• Easily adapts to the surface being treated• Excellently absorbs dust• Glides easily along the surface• User-friendly• No need in supplementary devices.Substrates Metal parts, rubber, glass, chrome-plated surfaces, putties, primers/fillers, OEM/refinishing coatings.


6-110-0001 80 cm х 90 cm 1


6-100-0005 80 cm х 50 cm, folded 5


8-800-0400 320 mm х 400 mm, roll 400

41catalogue 2014


woolen Polishing Discs VelcroWoolen polishing discs with self attachment Velcro system. To be used with Universal Polishing Paste.

Foam Polishing Discs VelcroFoam polishing discs with self attachment Velcro system.

Pads for Polishing Discs VelcroVelcro foam polishing pad for finish polishing jobs.


5-100-0150 Diam. 150 mm 1

5-100-0180 Diam. 180 mm 1


5-100-0001 For disc diam. 180 mm, M14 1

5-100-0002 For disc diam. 150 mm, M14 1


5-100-0161 Hard, diam. 150 mm 1

5-100-0162 Medium-Hard, diam. 150 mm 1

5-100-0163 Soft, diam. 150 mm 1

POLISHING MATERIALS

42catalogue 2014

nitrile GlovesSynthetic nitrile rubber gloves with high resistance to organic solvents (benzene, benzines), formaldehyde, ketones, ethers, acids and oils.The gloves efficiently prevent non-organic and grease contaminants from getting onto the paintwork. The product complies with the standard EN 455-3.

Latex GlovesThe gloves can be used while working with chemicals, except solvents and formaldehyde. They also prevent non-organic solvents and grease from getting onto the paintwork. The gloves are NOT powdered, and therefore, can be used in paint manufacturing. The product complies with the standards EN 374-1/2/3.

Vinyl GlovesGloves designed to provide hand skin protection from technical contaminants (paints, solvents, etc.) and prevent non-organic substances and grease from getting onto the paintwork. The gloves are NOT powdered, and therefore, can be used in paint manufacturing.


3-270-0100 size XL 100

3-270-0200 size L 100


3-260-0100 size XL 100

3-260-0200 size L 100


3-250-0100 size XL 100

3-250-0200 size L 100

ACCESSORIES

43catalogue 2014

Paint CoverallLight and comfortable paint overall made of processed cellulose impregnated with polyethylene which makes it more durable and prevents skin exposure to liquid and aerosol materials.The overall is outfitted with a zip fastener and elastic cuffs on sleeves, pant legs and hood for overspray protection.

Disposable Paint StrainersPaper filter with an insert made of artificial material for filtering paint and similar materials based on organic solvents. The strainer efficiently removes foreign particles that can get into refinishing materials and cause spray gun clogging.

Metal test CardMetal test card for testing automobile paints prior to application. Suitable for application of solventborne, and waterborne paints.


3-265-0001 size L 1

3-265-0002 size XL 1


7-700-0100 105х150 100


7-850-0125 125 μm 1000

3-850-0190 190 μm 1000

ACCESSORIES

44catalogue 2014

Mixing CupsHigh-quality solvent proof cups and lids for accurate mixing of refinishing materials: paints, clear coats, fillers, etc. A mixing ratio scale is printed on the side of the cup.


3-200-0385 cup 0.385 l 200

3-200-0750 cup 0.750 l 200

3-200-1400 cup 1.4 l 200

3-200-2300 cup 2.3 l 100

3-222-0385 lid for cup 0.385 l 200

3-222-0750 lid for cup 0.750 l 200

3-222-1400 lid for cup 1.4 l 200

3-222-2300 lid for cup 2.3 l 100

ACCESSORIES

Pump SprayThe sprayer with an air pump is intended for spraying silicone removers and thinners/cleaners. It is made of plastic that is resistant to said materials.


3-255-0001 1 L 1

Sanding Block for 150-mm Abrasive DiscsManual sanding block for 150-mm abrasive discs.


5-170-0001 Polyurethane, Velcro 1

45catalogue 2014

rubber Sanding BlockRubber block for sanding works.

Manual Polishing & Sanding PadVelcro back-up pad for polishing and sanding discs.


5-170-0004 Polyurethane, for 150 mm discs 1


5-170-0002 Rubber, 67 х 125 mm 1

ACCESSORIES

Flat Sanding BlockSanding block with a flat working surface for manual sanding of small and inaccessible areas.


5-170-0005 70 x 125 mm 1

46catalogue 2014

Semi-round Sanding BlockSanding block with a semi-round working surface for manual sanding of small, complex-shaped and inaccessible areas.

Masking Film Dispenser


5-170-0006 70 x 125 mm 1

The dispenser allows one person to perform complete vehicle masking.


1-205-0001 Steel 1

Dispenser accommodating 3 separate rolls of masking paper at a time, fitted with masking tape-removing rollers. Perfect solution for fast and cost-saving masking to provide overspray protection to vehicles.

Mobile Masking Paper Dispenser


1-225-0001 Steel 1

ACCESSORIES

rotating Paint StandMultipurpose rotating paint stand with spray gun holders and a set of fixtures for extensions. The paint stand provides aid in refinishing car doors, bonnets, trunk lids, etc.


3-100-0001 With 8 extensions 1

catalogue 2014

Folding Paint Stand PremiumFolding stand for securing the workpiece in a convenient position for the painter. The stand is very stable and accommodates bulky and heavy parts.


3-105-0001 With 2 additional fasteners 1

ACCESSORIES

For notes

August Handel GmbHSeestraße 33 –Brandenburg Park14974 Ludwigsfelde (Berlin)

Phone: +49 3378 / 20333-0Fax: +49 3378 / 20333-19E-mail: [email protected]

2014 - colorama · steel (incl. galvanized), aluminum, fiberglass plastic, oem substrates*. keep...

Documents