2006 - rw2000 - installation v1.3 copy

7/18/2019 2006 - RW2000 - Installation v1.3 Copy

http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 1/30

RADWIN 2000Installation

V1.3Release 2.6.40 LA



Introduction

RADWIN Training Center 2

Easy and fast, self-installation

Ready for Installation, no pre-installation setting is required

Link alignment and synchronization without external means

Antenna alignment is based on buzzer (1 dB accuracy)

Four simple steps for the entire link configuration

Link Budget Calculator for network planning

Installation Rate 6.5 Mbps (BPSK) robust for all cases

Using a unique ID (SSID)



Between the sites» Line Of Sight (Azimuth)

»

Distance (<120 Km)» Potential Interference

On Site» Mounting procedure (Pole or Wall) ODU Grounding

» ODU-IDU Cable Routing (<100m)

» IDU Mounting and Power supply

Installation» Expected Results: “Link Budget Calculator”

» RADWIN Manager (NMS)

» Installation on PC Station

» Cable paving and IDU and ODU connection

» Power Up (AC/DC adaptor – IDU)

»

Antenna alignment (Buzzer) and Mounting» Run “Installation Wizard” via NMS

Site Survey



Installation Diagram


Dual Polarization

Antenna

Connectorized

ODU

Mounting

Pole

COAXCables

Grounding

Power feeds DC /

AC (via adapter)Dry Contact

To Network

CAT.5e ETH



Grounding

ODU Grounding

The system uses a Shielded CAT-5 cable to interconnect the ODU/IDU.

However, this shielding does not provide a good Lightning Discharge path, since it can not tolerate the high Lightning

Current surges.

In order to provide an alternate Lightning Discharge path, the ODU/Antenna Grounding posts should be connected to a

Ground Point by a 10 AWG short copper wire, as per NEC 810-21

IDU Grounding

The IDU’s grounding post should be connected to the internal Ground point, merely for Safety and ESD protection

reasons.

External Lightning Surge Suppressors

In order to minimize direct Lightning damages, an external well grounded CAT-5 Lightning Protector should be mounted

outside the building, located as near as possible to the entrance of the CAT-5 ODU-IDU interconnection cable.

3-rd party protectors may be used, e.g. Motorola’s 300SS, Hyperlink’s HGLN-CAT5 or Sixnet’s SP-ETH-2

Internal ESD Protection circuits

The system is designed to meet the ETSI / FCC /Aus/NZ / CSA EMC and Safety requirements

In order to fulfill these requirements, the system’s Telecom lines at the ODU/IDU are Transformer-isolated and include

internal ESD (Electro-Static-Discharge) Protection circuits




Proper lightning discharge path

Personnel safety guarantee

ESD (Electro-Static-Discharge) protection path

One of the major factors for RMAs is lack of grounding!

Grounding point

Grounding the ODU / IDU

Grounding point




Tower Collocation (ODUs are installed in crowded tower):

Use alternate/adjacent channels

At least 3 meters separation between co-located units

Use alternate polarization for adjacent channel units

Reduce Tx Power to the minimum based on LBC

Alternate frequency bands

Installation Guidelines




Antenna Alignment: Integrated / Bi-Polar


1. Set antenna (A) towards remote location (B) at 90°

Site A Site B

OFF

OFF





2. Power on Link and rotate antenna from 90° to 0°

Site A Site B

ONON





3. Rotate antenna from 0° to 180°

4. Scan back and listen to “buzzer” achieving

3 beeps – “best alignment”

Site A Site B

ONON





5. Mount the antenna in the “best alignment” position

6. Same for the elevation axis

7. Repeat for location B



Antenna Alignment: 2 External Mono-Polar


Using a coax cable with N-Type connectors, connect one antenna to the ANT 1 connector of the

ODU.

Align the first antenna following above slide

Unplug first antenna from ANT1 connector and connect it to ANT2 connector.

Using a coax cable with N-Type connectors, connect second antenna to the ANT 1 connector of the

ODU

Align the first antenna following above slide

* When working with one mono-polar antenna use ANT1 connector only!!



RADWIN Manager Default Parameters

Please note:

Only Installer mode allows for frequency band change, 5.3/5.4 GHz, and 2.5 GHz BRS configuration.

IP Address:» “Local Connection”- only used during day one

installation. Once link is configured, log in viaassigned IP address

Password:» Defined by which “User Type” is selected

User Type:» Operator- admin

» Installer- wireless

» Observer- admin

Read-Write Community: netman




Installation Wizard




Installation Wizard


After antenna alignment use

the installation wizard to

complete system

configuration

From this step and onward

you can examine the quality

and service availability of

the radio interface



Installation Wizard – Using the “Monitor Link”


When we launch the installation wizard, the ODUs fill in the Air Frame with Pilot Traffic to

evaluate the quality of the link, i.e. – what are the levels of existing interferences and

when do they exist

The Quality Bar shows the Service Availability According to the measured data



Installation Wizard – Link Attributes


Configure here:

Link ID

Link Name

Local Site Name

Remote Site Name

Link Password

Click “Next” to proceed



Installation Wizard – Changing Password


Click “Change” to change

the password

CLICK ME



Installation Wizard – Channel Selection (ACS)


Selecting all channels and

enabling ACS will allow the

Air Interface full flexibility

when determining the best

channel

You may narrow down the

number of channels that

participate in the process

You may also disable the

ACS process and select the

channels manually

Click “Next” to proceed

CLICK ME



Installation Wizard – Antenna Parameters


Click the “Configure”

button(s) to configure the

Antenna Parameters -

(see next slide)CLICK ME



Installation Wizard – Antenna Parameters


Antenna Parameters:



Installation Wizard - Service


Going back to the main menu

of the Installation Wizard,

here we can configure the

required Service:

ETH

ETH+TDM

Rate

You can initiate an “Evaluate”

check to re-examine the link

quality and availability

CLICK ME

CLICK ME

Next Slide



Installation Wizard – Configuring TDM Services


In this window you can select the

number of TDM ports

The total number of TDM ports

depend on the link quality and

availability

To select a port, simply click on the

RJ45 port icon(s)

CLICK ME



Installation Wizard – TDM Clock


To configure the clock

settings of TDM port(s),

simply right-click the port and

select the best scenario -



Installation Wizard


That’s it!

You have successfully

configured both sites of the

link

You’re ready to go….



Installing the Lightning Protection Kit



LP – Packing List

Item Quantity

LP Unit 1

Pole Mounting Band 1

Wall Mounting Unit 1

Shielded RJ45 Male Connector 2

CAT-5e Cable 50 cm 1



Installing the LP on the Tower (ODU End)

Before commencing with the installation, please read carefully the

following instructions:

Basic installation requires mounting and grounding 2 Lightening

Protection Units; One on the tower very close to the ODU and

another outside of the site/facility where the IDU is installed.

Instructions:

1. Mount the LP on the tower as close as possible to the ODU using the mounting ring

2. Ground the LP Unit using the GND screw

3. Connect the short CAT5e cable to the IDU connector on the ODU

4. Connect the other side of the cable to the LP Unit

5. Tighten the cable gland cap firmly

6. Connect the CAT-5e cable that goes to the IDU to the other side of the LP Unit.

7. Tighten the cable gland cap firmly8. Run the CAT-5e cable towards the IDU



Installing the LP next to the IDU/PoE

Instructions:

9. Mount the 2nd LP Unit as close as possible to the inlet hole of the site/facility where the IDU/PoE is installed10. Use the Wall Mounting Unit to firmly secure the LP Unit on the site/facility wall

11. Ground the LP Unit using the GND screw

12. Remove the cap of the cable gland that is facing the ODU, make sure you remove the rubber sealing tube as

well

13. Plug into the half open cable gland the CAT-5e cable coming from the ODU

14. Tighten the cable gland cap firmly

15. Connect the short CAT-5e cable (provided in kit) to the half open cable gland of the LP and the other end

16. Connect the other end of the short CAT-5e cable to the IDU/PoE



Thank You!

2006 - rw2000 - installation v1.3 copy

Documents