2-way wireless security suite gs2060/tl260gs product technical training

2-Way Wireless Security Suite

GS2060/TL260GS Product Technical Training


GS2060/TL260GS– Product Overview


GS2060

GS2060 GSM/GPRS Wireless Alarm Communicator

Overview:The GS2065 provides primary or backup GSM/GPRS communication for Power Series PC1864/1832/1616 control panels

Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx15mm)• Weight : 310 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the Panel Bell output)• Current Draw : 65 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C

(40º F to 104º F)


GS2060


Features:• Back up and primary GSM/GPRS alarm communication• Panel remote uploading/downloading support via GSM/GPRS • Individual Periodic Test Transmission via GSM/GPRS• Supervision heartbeats via GSM/GPRS• 128-bit AES encryption over GSM/GPRS• Full event reporting• SIA format• PC-Link connection• SIM card included• Signal strength and trouble display• Activating and initializing through Connect 24• Quad-Band: 850 MHz, 1900 MHz, 900 MHzand 1800 MHz


GS2060


Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)

Compatible Control Panel & CabinetControl panel: Power Series PC1864/1832/1616 version 4.1 and higherCabinet: PC5003C and PC4050C

Product Model and Accessories:GS2060GS-USA: For US market with AT&T SIM cardGS2060GS-CDN: For Canada market with Roger SIM cardGS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cable


TL260GS

TL260GS Internet and GSM/GPRS Dual-Path Alarm Communicator

Overview:The TL260GS is an Internet and GSM/GPRS Dual-Path alarm communication for Power Series PC1864/1832/1616 control panels

Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx18mm)• Weight : 320 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the Panel Bell output)• Current Draw : 100 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C

(40º F to 104º F)


TL260GS


Features:• Fully redundant Internet and GSM/GPRS dual-path alarm

communication• Integrated call routing• Panel remote uploading/downloading support via GSM/GPRS

and Internet• Individual Periodic Test Transmission via GSM/GPRS and

Internet• Supervision heartbeats via GSM/GPRS and Internet• 128-bit AES encryption via GSM/GPRS and Internet• Full event reporting• SIA format• PC-Link connection• SIM card included• Signal strength and trouble display• Activating and initializing through Connect 24• Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz


TL260GS


Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)

Compatible Control Panel:Control panel: Power Series PC1864/1832/1616 version 4.1 and higherCabinet: PC5003C and PC4050C

Product Model and Accessories:TL260GS-USA: For US market with AT&T SIM cardTL260GS-CDN: For Canada market with Roger SIM cardGS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cable


UL Approval List

GS2060 GSM/GPRS Wireless Alarm CommunicatorTL260GS Internet and GSM/GPRS Dual-Path Alarm Communicator

UL Commercial Burglary•Listed as a primary communication channel (heartbeats must be enabled)

•Listed as a back-up in conjunction with the POTS (daily test transmission)

•Used as Dual Signaling Line Communication System (redundancy must be enabled)

•Used as Standard Line Security and Encrypted Line Security System (heartbeats and encryption must be enabled)

UL Residential Burglary and Fire •Listed as a primary communication channel (monthly test transmission)

•Listed as a back-up in conjunction with the DACT (monthly test transmission)


ULC Approval List

GS2060 GSM/GPRS Wireless Alarm CommunicatorTL260GS Internet and GSM/GPRS Dual-Path Alarm Communicator

ULC Commercial Burglary and Fire •Listed as a passive communication module with Security Level P1, P2 and P3 (redundancy must be enabled)

•Listed as a active communication module with Security Level A1-A4 (heartbeats and encryption must be enabled)

ULC Residential Burglary and Fire •Listed as a primary communication channel (daily test transmission)

•Listed as a back-up in conjunction with the DACT (daily test transmission)


UL/ULC Listed Installation – Commercial

Supervisory/Test Transmission Requirements

Applications CommunicatorSetup Mode

GS2060 TL260GS

Primary Channel

Backup Channel

UL Commercial Burglary Primary 200 ms 200 ms Daily

UL Commercial Burglary Backup Daily Daily Optional

ULC Commercial Fire Active 180 ms 180 ms Daily

ULC Commercial Fire Passive Daily Daily Daily

ULC Commercial Burglary Active 180 ms 180 ms Daily

ULC Commercial Burglary Passive Daily Daily Daily

NOTE: Proper Supervisory/Test Transmission intervals could be pre-set with the profile in Connect 24 database for applicable installations.


UL/ULC Listed Installation – Residential

Supervisory/Test Transmission – Requirements

Applications CommunicatorSetup Mode

GS2060 TL260GS

Primary Channel

Backup Channel

UL Residential Fire Primary Monthly Monthly Monthly

UL Residential Fire Backup Monthly Monthly Optional

UL Residential Burglary Primary Monthly Monthly Monthly

UL Residential Burglary Backup Monthly Monthly Optional

ULC Residential Fire Active Daily Daily Optional

ULC Residential Fire Passive Daily Daily Optional

ULC Residential Burglary Active Daily Daily Optional

ULC Residential Burglary Passive Daily Daily Optional

NOTE: Proper Supervisory/Test Transmission intervals could be pre-set with the profile in Connect 24 database for applicable installations.


GS2060/TL260GS– Installation and programming


Installation

GS2060/TL260GS Installation

BEFORE YOU BEGIN

Have the following ready before installation:

• PC1864/1832/1616 Control panel with backup battery• Battery connection harness• PK5500 keypad with battery • Screwdriver

Prior to installing a GS2060 and TL260GS, contact your monitoring station to determine if it is a master reseller or visit www.connect24.com and become an authorized dealer. In both instances, you will acquire a Profile Number, Installer ID Number and an Installer Password.

Please NOTE: 1. You need to activate the SIM card and initialize the communicator (step 1) 24

HOURS BEFORE INSTALLATION.

2. All options of the communicator only could be programmed through Connect 24


Installation


Summary of Installation Steps

Step 1 – Initialize an account via Connect 24 Website (www.connect24.com)

Step 2 – Install and wire the communicator to the control panel (on-site)

Step 3 – Load the programming and test for best signal strength location

Step 4 – Program communication options on the control panel via keypad

Step 5 – Test communication


Installation


Step 1 – Initialize an account via Connect 24 Website (www.connect24.com)

Login to Connect 24 website by using Installer ID and Password to initialize an account• Select Profile Number• Select Product Model• Enter SIM card number • Enter DNIS number (if necessary)• Enter Account Code• Select GPRS Periodic Test Transmission Interval (if necessary)• Select Supervisory Type (if necessary)• Enable DHCP (if necessary)• Enter IP Address (TL260GS only when the installation is static IP)• Enter Subnet Mask Address (TL260GS only when the installation is static IP)• Enter Gateway Address (TL260GS only when the installation is static IP)• Select Ethernet Periodic Test Transmission Interval (if necessary)• Select Rate Plan• Confirm information and submit activation application

NOTE: You still can remotely change these options later via Connect 24 website.


Installation


Step 1 – 1Select Profile Number

Select Profile


Installation


Step 1 – 2Select Module Number

Select ProfileSelect Module Number


Installation


Step 1 – 3Enter SIM Number

Select ProfileEnter SIM Number


Installation


Step 1 – 4• Enter DNIS number • Enter Account Code• Select Supervisory Type• Enable DHCP (if necessary)

Select Profile

Enter DNIS

Enter Account Code

Select Supervisory Type

DHCP Option


Installation


Step 1 – 5• Enter IP Address (TL260GS only)• Enter Subnet Mask Address (TL260GS only)• Enter Gateway Address (TL260GS only)

Select Profile

IP Address

Subnet Mask

Gateway


Installation


Step 1 – 6• Select Plan Rate

Select Profile

Rate Plan


Installation


Step 2 – 1 Install and wire the communicator to the control panel (on-site)

•Assemble the communicator with mounting bracket


Installation



•Insert the communicator into the cabinet and assemble the antenna


Installation



•Wire the communicator to control panel

NOTE: See details in product manual for PC1864/1832/1616 control panel

PCLINK Cable Connector•Control panel: Red wire is on the right and black is on the left

•Communicator: Must be reversed (Black wire is on the right and red wire is on the left)


Installation


Step 3 – Load the programming and test for best signal strength location

Ensure the SIM card is inserted Power up the control panel

The communicator will be programmed by loading the pre-programmed configuration from Connect 24 automatically

Check Green LEDs. You must achieve full or medium signal strength. See details in product manual.

If signal strength is poor, must relocate the control panel or use an external extension antenna kits


Installation


Step 4 – Program communication options on the control panel via keypad

GS2060/TL260GS with PC1864/1832/1616 control panel o Sections [301], [302], [303]: Program Communication Path

• DCAA - Internal (Ethernet 1, Ethernet 2, GPRS 1, GPRS 2)

o Section [350] : Program Communication Format (Communicator)

• (If Option [301] (above) is set to DCAA, Option [350] must be

set to SIA, sub-option 5)

o Sections [351] to [376] : Program Call Direction

o Section [382] : Enable T-LINK Interface (Option [5])

o Section [167] : Enable Communication Wait For ACK (Set to 60 seconds)

o Section [401] : Enable DLS Session Through GPRS or Ethernet (Option [1])


Installation


Step 5 – Test communication

1. Disconnect incoming phone line from TIP and RING on the control panel 2. Verify that LED 2 is on, this indicate that the unit is active3. Create an alarm transmission 4. Verify alarm transmission by calling monitoring station5. Re-connect the phone line, if necessary

For back-up communication applications, perform steps 1 to 5For primary communication applications, perform steps 3 and 4 only


Installation

LED Display

Trouble Status LED (Yellow – first one from the left)

Please see details about the trouble shooting on page 17 in product manual


Installation

LED Display

Network Connection Status LED (Red – second one from the left)

LED OFF•No network connection issue present

LED ON•Physical Ethernet cable is not connected•DHCP configuration fails•Fails to get an IP address from the GPRS network•GPRS connections has been reset

LED blinks quickly once•Ethernet transmitting

LDE blinks quickly twice•Ethernet receiving


Installation

LED Display

Signal Strength LED 2 (Green – third one from the left)Signal Strength LED 1 (Green – fourth one from the left)

Green LED 2 blinks quickly once•GPRS transmitting

Green LED 2 blinks quickly twice•GPRS receiving


Installation

Keypad Trouble Display

Trouble Condition•General System Trouble

Panel Event Buffer Description•T-Link Network Fault/Restore includes

SIM Lock TroubleGSM TroubleEthernet Trouble Connect 24 Configuration Trouble

•T-Link Receiver Trouble/Restore includes Receiver Not Available TroubleReceiver Supervison TroubleFTC Trouble

•T-Link Comm. Fault/Restore includesPanel Absent Trouble


GS2060/TL260GS– Applications


Applications

GS/IP Call Routing (Internal)

Communicator Controlled Call Routing – Backup (dual-path)

– Redundant (dual-path)

Required ProgrammingPanel Sections [301], [302] and [305]

• Any of them could be programmed as DCAADCAA (default): Ethernet 1 → Ethernet 2 → GRPS 1 → GPRS 2

Communicator Sections [005]Option [4] - Primary and backup path

[ON]: GPRS path primary, Ethernet path backup

[OFF]: Ethernet path primary, GPRS path backup

Option [5] - Redundant between GPRS path and Ethernet path [OFF]: Disable

redundancy[ON]: Enable redundancy

NOTE: “Primary and Backup Path” and “Redundant Communication” options need to be configured during the initialization of the account via Connect 24.


Applications


Backup Mode 1: Ethernet Primary, 4 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver* 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

Tx 2 failed, TX3

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2


Applications


Backup Mode 2: Ethernet Primary, 2 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2

Tx 2 failed, TX3


Applications


Backup Mode 3: GPRS Primary, 4 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

Tx 2 failed, TX3

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2


Applications


Backup Mode 4: GPRS Primary, 2 Receivers

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

TX 1

Tx 3 failed, Tx4

Tx 1 failed, Tx2

Tx 2 failed, TX3


Applications


Redundant Mode: 4 Receivers – (Redundancy between GSM/GPRS path and Ethernet/Internet path)

Ethernet Receiver 1

Ethernet Receiver 2

GPRS Receiver 1

GPRS Receiver 2

IP Receiver 1

IP Receiver 2

IP Receiver 3

IP Receiver 4

TX1, GPRS path

TX 1, Ethernet path

TX 1 failed, TX 2 via GPRS path

TX1 failed, TX 2 via Ethernet path

NOTE: The application requires 4 different SG receivers or SG-DLR3 IP line cards


Applications

Other Applications

Periodic Test transmission•Individual periodic test via GPRS and Ethernet•Daily, Weekly and Monthly Interval•Configured during the initialization of the account via Connect 24

Encryption•128 Bit AES Encryption •Turned on by central monitoring station Sur-Gard receiver•Encrypted communications enabled after next event sent to the receiver

NOTE: Enabling this feature will require more data usage.

Read-only Options from Keypad•Read all the options of the communicator from LCD keypad•Control panel option [851]


Applications

Other Applications

Power Save Mode•Extend the battery duration when an AC power loss on control panel•Ethernet functionality turned off until a new event need to be transmitted•Network Connections LED: OFF•Incoming DLS connection will not be possible

Hardware Default •Reset the programming options to the factory setting (default values)NOTE: Please see details in product manual

Software Update •Update the firmware through DLS IV locally via PCLINK•Update the firmware through DLS IV remotely via Ethernet/Internet (TL260GS only)


Applications

SIA Report Code

Event SIA Data Code SIA Address Field Panel Absent Trouble ET 001Panel Absent Trouble Restore ER 001Radio Activation Restore RS 001Ethernet 1 Test Transmission RP 001GPRS 1 Test Transmission RP 003GPRS 2 Test Transmission RP 004FTC Restore YK 001

Example: Nri0 ET001 N= New Eventri0=Partition/Area identifierET= Panel Absent Restore 001=Zone 001

NOTE: GPRS 2 Test Transmission will only be sent when two different APNs are programmed.

2-way wireless security suite gs2060/tl260gs product technical training

Documents

backup gsmgprs communication

gsmgprs supervision

standard line security

security level p

redundant internet

passive communication

internetsupervision

aes encryption