2 trulux spec grade tape light - american lighting · sptl = ip54 spec grade sptl65 = ip65 spec...

3
Page 1 of 3 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633 TRULUX Spec Grade Tape Light 24V ©2020 American Lighting, Inc. REV2039 www.AmericanLighting.com +24V +24V +24V +24V +24V +24V +24V 4V +2 +24V 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 +24V +24V +24V +24V +24V +24V +24V 4V +2 +24V 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 620 Technical Information Description Economical and versatile tape light with light output ranging from 280-570 lumens and run lengths up to 13.1ft Features Unjacketed (IP54) or Jacketed (IP65) rating options Linking accessories, controllers, receivers, power supplies, and extrusions are available for Trulux tape light (sold separately) Mounting Recommended use is to mount via an aluminum extrusion (recessed or drywall type - sold separately) to allow proper dissipation of heat. Recommended use for commercial applications includes soldering all connection points. Applications Task or accent lighting, edge lighting, cabinetry, shelving, coves, staircases, toe kicks, railings, display cases IP Rating IP54 IP65 Voltage 24V DC 24V DC CCT 2400K 2700K 3000K 4000K 2400K 2700K 3000K 4000K CRI 94+ 96+ 96+ 96+ 94+ 94+ 94+ 94+ Wattage 7.8W/ft 7.8W/ft Lumens 480Lm/ft 485Lm/ft 525Lm/ft 570Lm/ft 390Lm/ft 390Lm/ft 480Lm/ft 510Lm/ft Max Run 13.1ft 13.1ft Cutting 1.97” 1.97” Dimming Trulux controllers or most low-voltage electronic dimmers LED LEDs spaced every 0.31” LEDs spaced every 0.31” Beam 120° Operating Temp 5°C (41°F) to 70°C (158°F) Ambient Temp -20°C (-4°F) to 40°C (104°F) Rating cULus Listed, dry & damp locations, JA8 cULus Listed, wet locations, JA8 Rated Life 50,000 Hours 50,000 Hours PROJECT: CAT: LOCATION: TYPE: Dimensions: IP54 Unjacketed SPTL 10mm (13/32”)W 1.65mm (1/16”)H Dimensions: IP65 Jacketed SPTL 10.05mm (13/32”)W 3mm (1/8”)H Recommended use for commercial applications includes soldering all connection points. Recommended use is to mount via an aluminum extrusion to allow proper dissipation of heat. When using standard snap connectors, it is recommended to scrape off the coating from each conductor to ensure a proper connection. When using heavy duty snap connectors, this is only necessary for IP65 and IP68 types. Trulux Controller Set-up Push Dial Controller (Single zone) SR-1009FA LED CONTROLLER SEC ° tc=75°C PRI: Uin=12-36VDC Iin=20.5A SEC: Uout=4x(12-36)VDC Iout=4x5A Pout=4x(60-180)W TEMP RANGE:-20°C-+50°C Trulux RF Receiver (Required per zone) Push ON/OFF Trulux Tape Light Adaptive LED Driver (30W / 60W / 96W / 192W / 288W) Primary Side Dimming Set-up Standard Dimmer Trulux Tape Light Adaptive LED Driver (30W / 60W / 96W / 192W / 288W)

Upload: others

Post on 08-Aug-2020

8 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: 2 TRULUX Spec Grade Tape Light - American Lighting · SPTL = IP54 Spec Grade SPTL65 = IP65 Spec Grade SPTL Example Part # SPTL-UWX UWX NOTES Trulux Spec Grade is also available in

Page 1 of 3 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633

TRULUX Spec Grade Tape Light24V

©2020 American Lighting, Inc. REV2039 www.AmericanLighting.com

+24V+24V +24V+24V +24V+24V+24V+24V +24V+24V+24V+24V +24V+24V +24V+24V +24V+24V

620

620

620 620

620

620 620

620

620 620

620

620620

620

620 620

620

620620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620

+24V+24V +24V+24V +24V+24V+24V+24V +24V+24V+24V+24V +24V+24V +24V+24V +24V+24V

620

620

620 620

620

620 620

620

620 620

620

620620

620

620 620

620

620620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620 620

620

620

Technical Information

DescriptionEconomical and versatile tape light with light output ranging from 280-570 lumens and run lengths up to 13.1ft

Features• Unjacketed (IP54) or Jacketed (IP65) rating options• Linking accessories, controllers, receivers, power supplies,

and extrusions are available for Trulux tape light (sold separately)

MountingRecommended use is to mount via an aluminum extrusion (recessed or drywall type - sold separately) to allow proper dissipation of heat. Recommended use for commercial applications includes soldering all connection points.

ApplicationsTask or accent lighting, edge lighting, cabinetry, shelving, coves, staircases, toe kicks, railings, display cases

IP Rating IP54 IP65

Voltage 24V DC 24V DC

CCT 2400K 2700K 3000K 4000K 2400K 2700K 3000K 4000K

CRI 94+ 96+ 96+ 96+ 94+ 94+ 94+ 94+

Wattage 7.8W/ft 7.8W/ft

Lumens 480Lm/ft 485Lm/ft 525Lm/ft 570Lm/ft 390Lm/ft 390Lm/ft 480Lm/ft 510Lm/ft

Max Run 13.1ft 13.1ft

Cutting 1.97” 1.97”

Dimming Trulux controllers or most low-voltage electronic dimmers

LED LEDs spaced every 0.31” LEDs spaced every 0.31”

Beam 120°Operating Temp 5°C (41°F) to 70°C (158°F)

Ambient Temp -20°C (-4°F) to 40°C (104°F)

Rating cULus Listed, dry & damp locations, JA8 cULus Listed, wet locations, JA8

Rated Life 50,000 Hours 50,000 Hours

PROJECT:

CAT:LOCATION:

TYPE:

Dimensions: IP54 Unjacketed SPTL

10mm(13/32”)W

1.65mm(1/16”)H

Dimensions: IP65 Jacketed SPTL

10.05mm(13/32”)W

3mm(1/8”)H

Recommended use for commercial applications includes soldering all connection points.Recommended use is to mount via an aluminum extrusion to allow proper dissipation of heat.

When using standard snap connectors, it is recommended to scrape off the coating from each conductor to ensure a proper connection. When using heavy duty snap

connectors, this is only necessary for IP65 and IP68 types.

Trulux Controller Set-up

Push Dial Controller(Single zone)

SR-1009FALED CONTROLLER

INPU

T12-36V D

CPR

I

SEC

Learning Key

MASTER SLAVE

CW W

WW B

CW G

WW R

° tc=75°C

150805V1

PRI:Uin=12-36VDCIin=20.5ASEC:Uout=4x(12-36)VDCIout=4x5APout=4x(60-180)WTEMP RANGE:-20°C-+50°C

Trulux RF Receiver(Required per zone)

Push ON/OFF

Trulux Tape LightAdaptive LED Driver(30W / 60W / 96W / 192W / 288W)

Primary Side Dimming Set-up

Standard DimmerTrulux Tape LightAdaptive LED Driver

(30W / 60W / 96W / 192W / 288W)

Page 2: 2 TRULUX Spec Grade Tape Light - American Lighting · SPTL = IP54 Spec Grade SPTL65 = IP65 Spec Grade SPTL Example Part # SPTL-UWX UWX NOTES Trulux Spec Grade is also available in

Page 2 of 3 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633

TRULUX Spec Grade Tape Light24V

©2020 American Lighting, Inc. REV2039 www.AmericanLighting.com

Recommended Power Supplies

Part Number Description Application Primary / Secondary Total Wattage Listing Dimensions

For Trulux Controlled SystemsLED-DR30-24 Constant voltage hardwire driver Dry location 100-240 AC / 24V DC 30W cURus 6-1/2”x1-3/4”x1-3/16”LED-DR60-24 Constant voltage hardwire driver Dry/Damp location 100-240 AC / 24V DC 60W cURus 7-13/16”x1-3/4”1-5/8”LED-DR100-24 Constant voltage hardwire driver Dry/Wet location 100-240 AC / 24V DC 100W cURus 7-5/8”x2-1/8”1-1/2”LED-DR150-24 Constant voltage hardwire driver Dry/Wet location 100-240 AC / 24V DC 150W cURus 9”x2-5/8”1-1/2”

For Non-Trulux Controlled SystemsELV-30-24 Constant voltage hardwire driver Dry location 100-130V AC / 24V DC 30W cETLus 7-1/16”x2-3/8”1-3/8”ELV-45-24 Constant voltage hardwire driver Dry location 100-130V AC / 24V DC 45W cETLus 7-1/16”x2-3/8”1-3/8”ELV-60J-24 Constant voltage hardwire driver Wet location 100-130V AC / 24V DC 60W cETLus 13-3/4”x3-1/16”x2-5/16”ELV-80J-24 Constant voltage hardwire driver Wet location 100-130V AC / 24V DC 80W cETLus 13-3/4”x3-1/16”x2-5/16”

Trulux Single Color Control Options

Image Part Number Description

Trulux Controllers

SRF-BATT Trulux Single Color Radio Frequency Control; Push Dial Wall Mount; Single zone; Battery operated (CR2032 included); Requires the use of a Trulux Radio Frequency receiver

SRF-4Z-3P Trulux Single Color Radio Frequency Control; Touch Slider Wall Mount; 1-4 zones; 12V/24V DC input; Requires the use of a Trulux Radio Frequency receiver

Trulux AppTrulux Mobile Application; Mobile Phone or Tablet ready, interactive dial controls;

Available on Google Play or the App Store; Requires the TruHub (RF-WiFi-8) router and receivers (REC-5A-4Z) for 2-8 zones or the RF + WiFi receiver (REC-5A-4Z-WiFi) for single zone applications

Trulux Receivers

REC-5A-4ZTrulux Radio Frequency Receiver; Sync multiple receivers to a single control;

4 x (60-180W) 5A per channel; 12V/24V DC input; For use with Trulux Radio Frequency control or Trulux TruHub plus Trulux App

REC-5A-4Z-WIFITrulux Radio Frequency + WiFi Receiver; Sync multiple receivers to a single control;

4 x (60-180W) 5A per channel; 12V/24V DC input; For use with Trulux Radio Frequency Control or Trulux App

WIFI-RF-8 TruHub WiFi Hub Control; converts WiFi to RF for 2-8 zones; For use with REC-5A-4Z and Trulux App

ELV Drivers require 60% minimum load in dimming applications

Page 3: 2 TRULUX Spec Grade Tape Light - American Lighting · SPTL = IP54 Spec Grade SPTL65 = IP65 Spec Grade SPTL Example Part # SPTL-UWX UWX NOTES Trulux Spec Grade is also available in

Page 3 of 3 11775 E. 45th Ave. Denver, CO 80239 Ph: 1-800-880-1180 Fax: 303-695-7633

TRULUX Spec Grade Tape Light24V

©2020 American Lighting, Inc. REV2039 www.AmericanLighting.com

Ordering Information

SPTL (IP54) 13.1ft Reels include:Attached 3ft lead wire(3) TL-2PWR power connectors(3) TL-2DC power connectors

SPTL65 (IP65) 13.1ft Reels include:(3) TL-CONKIT power connectors(1) Male IP65 power connector(1) Female IP65 power connector

TAPE LIGHT TYPE CCT

24V 13.1ft ReelsSPTL Series

UWX = 2400KUWW = 2700KWW = 3000KWH = 4000K

SPTL = IP54 Spec GradeSPTL65 = IP65 Spec Grade

SPTL

Example Part # SPTL-UWX

UWX

NOTES

Trulux Spec Grade is also available in Custom Cut (special order) lengths.

Image Part Number Description

TL-CONKIT TruLink 4-in-1 block connector kit with 36” lead wire (2pin, 18AWG wire); For dry, indoor location use only

TL-BLKS TruLink 4-in-1 block connector (2pin) (Bag of 10); For dry, indoor location use only

TL-2PWR-HD IP54 Power feed “Heavy Duty” snap connector to bare wires (2pin, 20AWG wire); For dry, indoor location use only

TL-2JUMP6-HD 6” IP54 Tape-to-tape “Heavy Duty” snap jumper (2pin, 20AWG wire); For dry, indoor location use only

TL-2JUMP24-HD 24” IP54 Tape-to-tape “Heavy Duty” snap jumper (2pin, 20AWG wire); For dry, indoor location use only

TL-2SPL-HD IP54 In-line splice “Heavy Duty” snap connector (2pin); For dry, indoor location use only

TL-2JUMP65-.5 6” IP65 Power-to-power jumper (2pin) - for IP65 tape

TL-2JUMP65-1 12” IP65 Power-to-power jumper (2pin) - for IP65 tape

TL-2JUMP65-2 24” IP65 Power-to-power jumper (2pin) - for IP65 tape

TL-ENDS65-10 End Caps (Bag of 10) - For IP65 or IP68 tape

TL-CLIPS-15 Mounting clips (Bag of 15) - For IP65 or IP68 tape

Connection Accessories