2 post lift - ravaglioli - rav · 2 post lift the "flexload 10" is the most innovative...
TRANSCRIPT
LIFTS
2 POST LIFT
The "Flexload 10" is the most innovative design in the two post lift market since the innovation of the asymmetric lift.
The unique carriage design allows for the stronger straight column to be utilized without using a 90 degree front arm reducing stress. The result, a longer lasting lift that Will give you years of service without arm distortion common on so many US/China hybrid lifts.
Adjustable height. Self-locking conical design
FLEXIBILITY
Very low pad, adjustable height Pulley protected inside the column
• Last stage of all arms are solid steel (no tubing) allowing the pad to be lower than then arm. This allows easier access on low clearance cars with troublesome pickup points without damaging the rocker panel.
• Pulling cylinders, although more expensive to produce, reduce stress on the seals creating longer life.
• Quality single point lock system with non-friction cables that run over pulleys for longevity.
QUALITY STANDARD FEATURES
The "Fiexload 10" is the only lift on the market with double wall column construction. Each column is constructed with 20 strength increasing bends making it the strongest column on the market.
4 7
6
10
8
9
5
4 7
6
8
5
Solid steel last stage always lower than lifting pad ..... arm won’t “bite” the rocker panel
3,5 HP motor / pump assembly ...stronger
adjustable height
lock release cable on pullies to eliminate friction...lasts longev
inch sheaves reduce cable wear for longev life
largest lock pawl in the industry... Safer
Show frame adapters in circle
syncronization cables fully galvanized throughout preventing premature
internal rust failure
positive conical brush locking gear...more secure locking
OPTIONS
Spacers
S370A18 (H=8”)
4x
S224A4 (H=5 1/2”)
4x
S370A5 (2 x kit)Set of door protections
S5.337A2Frame adapters
• Fully galvanized equalizing cables that will not rust from the inside out like US/China hybrids for more security.
• Non-slip rubber lifting pads with spin up adapters won't damage vehicle pick up points.
• Available in standard 142/146" model or Ultra Height 160/164" models ... ....... at no additional cast.
• 3 phase models available at no additional cost (special order).
• Absolutely no Chinese components.
EXTRA RESISTANTCOLUMN DESIGN
Exclusive 10+8 bending design to ensure max resistance to load.
Top productMade in Italy
FLEXLOAD
KPH370.42YKU
10,000 lbs
KPH370.42YKU + VAR3725/42YK
inside column 111”/115”
Overall Width 140”/144”
105 - 1/8”
140
- 3/4
”60
”37 -
5/8”
38 -
3/8”
19
3/8”
107
- 1/2
”
73 -
3/8”
5 - 3
/8”
4 - 1
/4”
146
- 1/8
”
109 - 1/8”
KPH370.42YKU
inside column 111”/115”
Overall Width 140”/144”
105 - 1/8”
158
- 1/2
”60
”37 -
5/8”
38 -
3/8”
19
3/8”
107
- 1/2
”
79 -
1/8”
5 - 3
/8”
4 - 1
/4”
164”
109 - 1/8”
STANDARD
S370A3 (2 x kit)Spacer supports
S224A3
3 ¼
”
10, 000 lbs
10, 000 lbs
10, 000 lbs
MAXLOAD 12-15
164”
157”
inside column 113”
Overall Width 147 - 1/2”
78 -
3/4”
5 - 1
/2”
max
4” m
ix
107 - 1/4”drive-thru 102”
121
- 3/4
”
56 -
1/2”
56 -
1/2”
28-3
/8”
28-1
/4”
29-5
/8”
56-7
/8”
70-7
/8”
147-
3/4”
33-1
/4”
drive-thru 104 - 1/4”110 - 3/4”
inside column 118 - 1/8”
171
- 175
”
80 -
3/8”
7 - 1
/8”
4 - 3
/4”
178
- 182
”
Overall Width 152 - 5/8”
KPH370.50LIKU
KPH370.55LIKU + VAR4625/55
12,000 lbs
12,000 lbs
12,000 lbs
12,000 lbs
15,000 lbs
15, 000 lbs
15, 000 lbs
15, 000 lbs
KPH370.50LIKU
KPH370.55LIKU
Top productMade in Italy
MAXLOAD 18
OPTIONS
KPH370.55LIKT KPH370.70LIKT
For Fiat Ducato, Peugeot Boxer, Citroën JumperSpacers
S224A3
S370A7(H=3 ¼”)
S224A4
S370A8(H=5 ½”)
S370A18
S370A15(H=8”)
4x
4x
4x
S370A19
S370A16
Frame adapters
4x
For Mercedes Sprinter, VW LT+Crafter Adapters
S370A17
S370A14
2x 2x
123 - 1/8”110 - 1/4”
140 - 1/2”
153 - 1/8”
min
.5 m
ax.7
1/2
”
190
1/4”
81 1
/8”
197
1/2”
(182
1/2
”) -
(174
1/2
”)
(189
1/2
”) -
(181
1/2
”)
Ø 4-7/8”
115 3/8”
33 1
/8”
33 1
/8” 70
7/8
”70
7/8
”22
”
KPH370.70LIKTU
18,000 lbs
STANDARD S370A7(H=3 ¼”)
S370A8(H=5 ½”)
+ S5.337A2Special support
4x
4x
18, 000 lbs
18, 000 lbs
18, 000 lbs
KPH370.70LIKTU
10,000 lbs
RAV 1110NKU• Perfect synchronization between
cylinders regardless of load distribution.
• Mechanical locking device with automatic engagement and pneumatic release, ensuring maximum safety when lift is raised.
Screw type pads can be adjusted as well as used with drop in extensions.
IN-GROUND HIGH PRESSURE
Vehicle access completely free.
30 SEC UP24 SEC DOWN30 SEC UP24 SEC DOWN
• Dual purpose hydraulic safety valve prevents overloading and unexpected lowering should hose failure occur.
• Controlled lowering speed.
• All mechanical, hydraulic and electrical components manufactured in compliance with ALI /ETL.
Pads can be adjusted in height and are suitable for quick housing of extensions.
10, 000 lbs
10, 000 lbs
10, 000 lbs
Extra low profile arms, parallel to the floor.
42 ¼”
3 2/4
”
3 ¾
”
RAV 1110NKU
81 ¼
”
Ø 4 ¾”
52 ¾”42
¼”
92”
101 ¼”120 ¾”
19 ¾
”
19 ¾
”
30 ¼
”
3 ¾
”-4
¾”
3 ¾
”
98 ¼
”
67 1/8”
Waterproof inground frame: steel frame and plastic cover.
Adjustable distance between the platform for different set-up pinch weld or frame vehicles.
The approach ramps can easily and quickly be locked in the horizontal position to serve as platform extensions.
Min. height: 3 7/8”
10,000 lbs
RAV 1120MU
RAV 1120MU
Ø 4 3/4”
52 3/4”
3 7/
8”
79 1
/4”
98 1
/4”
67 1/8”
79 1/2”41 3/4”18 7/8” 18 7/8”
76 7
/8”
55 7
/8”
26”18 7/8” 18 7/8”
63 3/4”
19 5/8”
Top productMade in Italy
IN-GROUND HIGH PRESSURE
Cross bar with double joint to eliminate vibrations
DOUBLE JOINT
Mechanical safety latch with automatic engagements ensuring maximum safety when lift is in standing position.
SAFE: MECHANICAL LOCK
MAINTENANCE FREE GUIDES
Columns guides in oil bath, maintenance free.
HARD CHROME COLUMNS
Hard chromed guide tubes will not rust
Each column features a maintenance-free lifting cylinder.
MAINTENANCE FREE CYLINDERS
Waterproof
inground fram
eWaterproof
inground fram
eWaterproof
inground fram
e
77”
56”
76”
10”
75”
11”
39”
24”
32”
24”
3,9”
EXPRESS SERVICE
Extra low version.The lift is an ideal choice for low ground clearance vehicles and in particular for extra low spoilers.The lift is recommended for vehicles with variable height, or damaged suspensions.
7,000 lbsMinimum height 3,9”
RAV 535U
All pivot points made with self lubricating bushings for long life.
SELF LUBRICATING
Mechanical locking device with automatic engagement and pneumatic release, ensuring maximum safety when lift is in standing position.
MECHANICAL LOCK
7, 000 lbs
7, 000 lbs
7, 000 lbs
RAV 535UShown w optional underfloor hoses
• No cross rails or torsion bars between lifting platforms (for maximum accessibility in the working area).
• Controlled speed during initial lifting and final lowering phase.
Shown w optional underfloor hoses
Top productMade in Italy
High capacity model with longer lifting plates.
9,000 lbsMinimum height 5,3”
EXPRESS SERVICE
81,9”
57”
76”
10”
75”
11”
39”
24”
32”
24”
5,3”
RAV 540U
OPTIONS
Set of pads (4 x kit)
S 505A1S 505A5S 505A6S 505A7
H= 8”H= 4 3/4”H= 1 1/2”H= 3/4”
S 505 A2 (2 x kit)Cross members To provide safe wheel free lifting of vehicles with narrow lifting points.
S 540A1Kit with additional run up ramps for low ground clearances vehicles
RAV 540U
9, 000 lbs
9, 000 lbs
9, 000 lbs
ALIGNMENT LIFT
All can be supplied for recessed installation.
RECESSED VERSIONS
Hydraulic levelling system by means
of a patented synchronisation device
assures constantly level lifting platforms regardless of weight
distribution.
Mechanical locking device with automatic engagement and pneumatic release, ensuring maximum safety when lift is rised.
OPTIONAL PIT INSTALLATION SHOWN IN THE PICTURE
10,000 lbs
RAV640.2
72 -
3/4”
47”
238”
23-1
/2”
16 1/4”
14”
221/2”
9”
40
1”
57” 181”
10-1
/2”
212”
29,3°
34 1/4”
24 1/4”
24 1/4”
82-3
/4”
68-1/2” 69-1/2” 35-1/2” RAV 640.2 + UE172
10, 000 lbs
Scissor10, 000 lbs
Scissor10, 000 lbs
Scissor
Top productMade in Italy
ALIGNMENT LIFT 14,000 Sci
ssor
alignment lif
t14,000 Sci
ssor
alignment lif
t14,000 Sci
ssor
alignment lif
t
Heavy duty air-hydraulic rolling jacks. Scissors type.
J30 PRU 7000 lbs
Version with front hydraulic play detector.
14,000 lbs
193”
4 - WHEEL ALIGNMENT WHEELBASE
2 - WHEEL ALIGNMENT WHEELBASE
GENERAL SERVICE WHEELBASE
195”
198”
216”
14,6”
23,6”
5,9”
TOTAL RUNWAYS LENGHT
14,000 lbsThe best solution for a rational workshop:• space saving when lift is raised • obstacle free floor space when lift is
fully lowered.
No cross rails or torsion bars between lifting platforms provides maximum accessibility in the working area.
Hydraulic levelling system by means of a patented synchronisation device assures constantly level lifting platforms regardless of weight distribution.
All pivot points made with self lubricating bushings for long life.
RAV 660.2.55U
RAV 660.5.55
72 -
3/4”
47”
277”
23-1
/2”
16 1/4”
14”
48”9”
40 1/4”
1”
57” 216-1/2”
10-3
/4”
251”
29,3°
35 1/2”
25 1/2”
25 1/2”
86-1
/2”
70” 68-1/2” 60-1/4” RAV 660.2.55U + UE172
ALIGNMENT LIFT
43’’ max - 37’’ min
21,5’’ 21,5’’
78’’
104’’118’’
90’’
9’’
102’’
137’’
9’’48
,5’’
63’’
61’’
278’’ 22
4’’
132’’
14,000 lbs
premiun alig
nment lift
14,000 lbs
premiun alig
nment lift
14,000 lbs
premiun alig
nment lift
MULTI – POSITION
Extra-long platforms for total wheel alignment with front turning plates locations and rear slip plates.
Everything flush mounted for smooth access and perfect alignment work.
Low-friction rear slip plates.They can be manually locked
in central position.Transverse and angular
movements in both directions.OPEN FRONT
Full access to the working area
Flat runways with front pocket
OPTIONSS4504 OF A1(for RAV 4504 OF)Kit to level S110A7 turntables for rolling run out compensation.
S110A712.2” diameter. Pair of heavy duty turntables.
Heavy duty air-hydraulic rolling jacks. Scissors type.
55’’
J30 7000 lbs each
RAV 4506 OFU
14,000 lbs
RAV 4504 OFU
14,000 lbsLift with flat runways, with front recess for turntables and rear sliding plates mounted over the platform.Low-friction rear slip plates. They can be manually locked in the central position. Transverse and angular movements in both directions.
RAV 4503 OFU
14,000 lbsFlat runways.The 224” long platforms and the large inner distance between posts allow optimum lifting of light commercial vehicles and long-wheelbase vans.
Alignment runways in front pockt pinned rear slip plates mounted over the platform
Multiposition tumplate cutouts with integral slide lock rear slip plates
Top productMade in Italy
ELECTROMECHANICAL
RAV212N, RAV222N, RAV232N: controls only on master column and operated as a set of 4 only.
RAV212NL, RAV222NL, RAV232NL: system can be operated from any post and individually as needed.
210-220-230-240 seriesHandle (1 per set)
Can be operated from any post.
19,000 lbs each column
RAV 262
22,500 lbs each column
RAV 272
1 set of 8
2 sets of 4
Possibility of setting a different heights between pairs of columns, retaining the subsequent level synchronization.
can become
AXLE HEIGHT SELECTION
MODULAR
Slave column control NL series
Master column control NL series
7,000 lbs each column
RAV 212
9,000 lbs each column
RAV 222
12,000 lbs each column
RAV 232
RAV 262
260-270 seriesHydraulic towing jack
16,000 lbs each column
RAV 242
OPTIONS
HYDRAULIC
Version on demand featuring adjustable forks for wheels from 500 to 1200 mm in diameter.
SPECIAL VERSION(gVAR 290/F)
S260A1015,000 lbs frame kit (2 each set)
WHEEL FREE CROSS-BEAM
S260A5 > max 15.000 kgS270A7 > max 20.000 kg
STANDS
1330 - 2030 mm
S260A1 / 7500 kg
1235 - 2040 mm
S270A1 / 10000 kg S270A2 / 10000 kg
1235 - 2040 mm
S270A2Spring-return wheels.
Simultaneous operation of all columns.Electronic system ensuring synchronization of all columns.Safety stop in case of malfunction.Low voltage controls (24 V) on the main column.
RAV 295H.4
12,000 lbs each column12,000 lbs12,000 lbs12,000 lbs
RAV 295HHandle (1 per set)
Top productMade in Italy
BATTERY
Control panel available on each column. All columns identical.Configuration sets: 4-6-8 columns.Mechanical locking system/parking.Wireless 2.4 GHz communication among columns.
CONFIGURATIONS
4 6 8
RAV 307H.4WS RAV 307H.6WS RAV 307H.8WS
Synchronization at a height difference of 30 mm.Control board according to ISO standards 13849.
ALL: Simultaneous operation of all columns.GROUP: Simultaneous operation of selected pairs of columns.SINGLE: Single column operation.
OPERATION MODES
SYNCHRONIZATION
2 batteries in each column, 12V 100 A/h, gel type, maintenance-free. 20 lifting cycles with full load.
Battery charge leds:- yellow led: battery charging
recommended, 5 cycles still possible.
- red led: battery charging is required, 1 lowering cycle still possible.
BATTERIES
LCD DISPLAY
KEY BOARD
SINGLE
PARKING
DOWN, SLOW (OPTION)EMERGENCY STOP
UP
DOWN
24V CONTROLS
- Operation modes (all, group, single)- Height of columns- Battery charge condition - Diagnostic / maintenance- Number of column in a set
DISPLAY INFORMATION
One battery charger in each column.10 meter charging cable. Battery charger works as such, it is not for power supply.Batteries can be charged during operation.Recharging time approx. 10 hours.
BATTERY CHARGER
VAR307H/WS/LS (> RAV 307HWS)VAR308H/WS/LS (> RAV 308HWS)Two lowering speed: standard and slow.
SPECIAL VERSION(gVAR 300/F)
OPTIONS
RAV 307H.4WS
16,000 lbs each column
RAV 305H.4WS
12,000 lbs each column
16,000 lbs
16,000 lbs
16,000 lbs
DATA TRASMISSION CABLE
260-270 seriesHydraulic towing jack
Top productMade in Italy
INTERNATIONALRavaglioli S.p.A.40037 Sasso MarconiFraz. Pontecchio M.P.O.B. 1690 - Bologna - Italia Tel. +39 - 051 - 6781511Fax +39 - 051 - [email protected] www.ravaglioli.com Technical data and composition presented in this catologue may vary. Pictures reproduced are only indicative.
Distributed by
Editi
on 0
02RAV Equipment U.S.A.
RAV Equipment [email protected]