2-arm pattern - farnell element14 · 2-arm pattern the new model for the safe and fast removal of...

315

1.04 Puller2-arm patternThe new model for the safe and fast removal of pulleys, wheels, ball bearings, etc. Due to the bending-moment reinforcement on its back face, the energy-saving design of the cross piece means even stronger and safer pulling work. With the newly-developed cantilever hook design, it is possible to use these higher forces without losses over the whole width of the cross piece. The high-speed adjustment feature supports the energy-saving and fast operation. The spindle possesses an interchangeable tip, meaning that a ball tip may also be employed if necessary.Spindle may be exchanged for hydraulic pressure spindle (see table).

1.06 Universal puller2-arm patternThe reliable model for the fast and safe removal of pulleys, wheels, ball bearings, etc. Strong drop forged design. Reversible hooks permit use as an internal or external puller. Available extras are replaceable hooks for various clamping reaches. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. a1 a2 min a2 max b A Hydraulic spindle $ c d e max. t 0

8000230 1.06/1 90 60 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.18000310 1.06/1A 130 70 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.38000580 1.06/2 160 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.28000660 1.06/2A 200 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.68000740 1.06/3 250 125 330 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 7.88000820 1.06/3A 350 125 420 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.28000900 1.06/4 520 185 600 200 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 15.28112970 1.06/5 640 230 715 225 G 1 x 310 1.06/HSP3 36 50 33 10,0 18,0 23.5


1307703 1.04/1A 130 70 170 100 M 14x1,5 x 140 17 22 15 3,0 3,0 1.21307827 1.04/2A 200 110 260 150 G 1/2 x 210 1.06/HSP1 22 30 25 4,5 5,0 3.31307940 1.04/3A 350 150 420 200 G 3/4 x 280 1.06/HSP2 27 36 33 6,0 7,5 9.9

1.06 Universal puller2-arm pattern, with extended hooksAs universal puller No. 1.06/1 to 1.06/4, but with extended pulling hooks. Spindle may be exchanged for hydraulic pressure spindle (see table).


8108350 1.06/1-2 90 60 140 200 M 14x1,5 x 140 17 22 12 3,0 3,0 1.58108430 1.06/1A-2 130 70 180 200 M 14x1,5 x 140 17 22 12 3,0 3,0 1.88108510 1.06/2-3 160 80 220 300 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.48108780 1.06/2A-3 200 90 260 300 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.88001200 1.06/3-3 250 125 330 300 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.18108860 1.06/3A-3 350 125 420 300 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 10.58108940 1.06/4-3 520 185 600 300 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 16.58109080 1.06/3-4 250 125 330 400 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 10.48109160 1.06/3A-4 350 125 420 400 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 11.88109240 1.06/4-4 520 185 600 400 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 17.88109320 1.06/3-5 250 125 330 500 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 11.68112380 1.06/3A-5 350 125 420 500 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 13.08112460 1.06/4-5 520 185 600 500 G 1 x 310 1.06/HSP3 36 36 28 6,5 10,0 19.0

Baldur_9_GB.mif Seite 315 Freitag, 18. Juli 2003 10:15 10

316

1.06 Universal puller2-arm pattern, with rigid hooksDesign as universal puller No. 1.06/1 to 1.06/4, but with rigid pulling hooks. For greater ease in setting the clamping spread. The hooks clamp automically when under tension. The hooks may be reversed to convert the puller from an external one to an internal one. Spindle may be exchanged for hydraulic pressure spindle (see table).


8001470 1.06/11 100 50 140 100 M 14x1,5 x 140 17 22 15 4,0 3,0 0.88001040 1.06/1A1 140 60 180 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.28001550 1.06/21 170 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 2.78001120 1.06/2A1 210 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.18001630 1.06/31 250 125 340 200 G 3/4 x 280 1.06/HSP2 27 36 32 5,0 7,5 6.68001390 1.06/3A1 340 125 430 200 G 3/4 x 280 1.06/HSP2 27 36 32 5,0 7,5 8.08109400 1.06/41 520 185 610 200 G 1 x 310 1.06/HSP3 36 36 32 5,0 10,0 14.0

1.06 Fast clamping puller2-arm pattern, with fast-clamp adjustmentThe tried and tested model for the safe and fast removal of pulleys, wheels, ball bearings, etc. Strong drop forged pattern. By reversing the hooks, this tool may be used as an internal or external puller. Exchangeable hooks for several clamping reaches available as accessories. With the innovative high-speed clamps, fast and uncomplicated setting-up and readjustment is child's play. Spindle may be exchanged for hydraulic pressure spindle (see table).


1213830 1.06/1-E 90 60 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.11215140 1.06/1A-E 130 70 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.31216570 1.06/2-E 160 80 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.21217720 1.06/2A-E 200 90 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.61218980 1.06/3-E 250 125 330 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 7.81220160 1.06/3A-E 350 125 420 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.2

1.06 Universal puller2-arm pattern, with slim hooksThe feet of the hooks are very slim and particularly suitable for barely-accessible places.

Code No. a b A $ c d e f max. t 0

8113510 1.06/S1 100 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.08113780 1.06/S1A 140 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.28114830 1.06/S2 160 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.08114910 1.06/S2A 200 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.2


317

Code No. a1 a2 b Spindle c d e max. t 0

8005700 1.06/2-3-HSP1 160 220 225 1.06/HSP1 30 18 3,5 5,0 4.88005890 1.06/2A-3-HSP1 200 260 225 1.06/HSP1 30 18 3,5 5,0 5.28005970 1.06/3-3-HSP2 250 330 225 1.06/HSP2 36 28 6,5 7,5 9.58006940 1.06/3A-3-HSP2 350 420 225 1.06/HSP2 36 28 6,5 7,5 11.48007240 1.06/4-3-HSP3 520 600 190 1.06/HSP3 36 28 6,5 10,0 18.48007670 1.06/3-4-HSP2 250 330 325 1.06/HSP2 36 28 6,5 7,5 10.48007750 1.06/3A-4-HSP2 350 420 325 1.06/HSP2 36 28 6,5 7,5 11.38007830 1.06/4-4-HSP3 520 600 290 1.06/HSP3 36 28 6,5 10,0 19.48007910 1.06/3-5-HSP2 250 330 425 1.06/HSP2 36 28 6,5 7,5 12.48008480 1.06/3A-5-HSP2 350 420 425 1.06/HSP2 36 28 6,5 7,5 13.48008560 1.06/4-5-HSP3 520 600 390 1.06/HSP3 36 28 6,5 10,0 20.4

1.06 HSP Universal pullerhydraulic, 2-arm pattern, with extended hooksFor the highest requirements. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.

1.06 HSP Universal pullerhydraulic, 2-arm pattern, with rigid hooksWith pulling hooks in one piece, drop forged pattern. By reversing the hooks, this tool may be used as an internal or external puller. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


8008640 1.06/21-HSP1 170 220 75 1.06/HSP1 30 24 3,5 5,0 3.78008720 1.06/2A1-HSP1 210 260 75 1.06/HSP1 30 24 3,5 5,0 3.88008800 1.06/31-HSP2 250 340 115 1.06/HSP2 36 32 5,0 7,5 7.08008990 1.06/3A1-HSP2 340 430 115 1.06/HSP2 36 32 5,0 7,5 8.88009370 1.06/41-HSP3 520 610 80 1.06/HSP3 36 32 5,0 10,0 14.8

1.06 HSP Universal pullerhydraulic, 2-arm patternThe tried and tested model for the safe and fast removal of pulleys, wheels, ball bearings, etc. Drop forged pattern. By reversing the hooks, this tool may be used as an internal or external puller. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


8000150 1.06/2-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 3.68002870 1.06/2A-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.08003170 1.06/3-HSP2 250 330 125 1.06/HSP2 36 28 6,5 7,5 8.28003920 1.06/3A-HSP2 350 420 125 1.06/HSP2 36 28 6,5 7,5 9.68004060 1.06/4-HSP3 520 600 90 1.06/HSP3 36 28 6,5 10,0 16.58004730 1.06/5-HSP3 640 715 110 1.06/HSP3 50 33 10,0 18,0 24.5


318

1.06 HSP Hydraulic pressure spindleThese grease-hydraulic pressure spindle has been designed for controlled and safe pulling work, and is set up for a pressure of up to 15 t.Preparation for use:1. Before using, check whether the pressure spindle is screwed far

enough out of the cap, so that the pressure pad is in the initial position in the hydraulic cylinder.

2. Unscrew the cap from the spindle body. For this purpose, first slacken off the grup screw.

3. Screw the spindle body from beneath into the cross piece of the puller until the body protrudes approx. 60 mm from the cross piece.

4. Screw the cap onto the spindle body until the stop, and then fix it in position by turning in the grub screw.Use and operation: e.g. HSP3

5. Place the puller into position and pre-tension the spindle body using a size 41 mm wrench.

6. Screw the pressure spindle size 17 mm into the cap. The hydraulic effect will come into use. The stroke of the pressure pad in the hydraulic cylinder is max. 12 mm. The workpiece that has been loosened by the hydraulic force may be pulled off completely by turning the spindle body with the cap size 41 mm.

7. Following its use, the pressure spindle (size 17 mm) is turned back into its initial position and the pressure pad pushed into the hydraulic cylinder.

Code No. a b c d e f Stroke mm max. t 0

8116100 1.06/HSP1 1/2" 55 135 350 12 32 12 12 1.18116290 1.06/HSP2 3/4" 80 205 420 12 36 12 12 1.88116370 1.06/HSP3 1" 125 165 465 17 41 12 15 3.6


1221256 1.06/2-E-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 3.71221450 1.06/2A-E-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.11221639 1.06/3-E-HSP2 250 330 125 1.06/HSP2 36 28 6,5 7,5 7.61221760 1.06/3A-E-HSP2 350 420 125 1.06/HSP2 36 28 6,5 7,5 8.8

1.06 Extension for pullersDGBMThe one-piece drop forged extensions enable the clamping reach to be extended indefinitely. The extensions may be used together with all hooks of the 1.06 range. (Delivery in pairs).DGBM = German Federal Utility Patent

Code No. B b 0

8036500 1.06/V100 for 1.06/A and 1.06/100 100 0.48036690 1.06/V150 for 1.06/B and 1.06/150 150 1.28036770 1.06/V200 for 1.06/C and 1.06/200 200 2.6

1.06 HSP Fast clamping pullerhydraulic, 2-arm patternWith the hydraulic spindle, a controlled and safe pulling action is possible at all times. With the innovative high-speed clamps, fast and uncomplicated setting-up and readjustment is child's play.


319

1.06 Pulling hooksset of 2 piecesPulling hooks (1 pair including clamping parts), in standard and special lengths.

Code No. B b c d e 0

8035020 1.06/A 1.06/1 /1A 100 22 12 3,0 0.68035100 1.06/B 1.06/2 /2A 150 30 18 3,5 1.68035290 1.06/C 1.06/3 /3A /4 200 36 28 6,5 3.58114400 1.06/D 1.06/5 225 50 35 11,0 3.58035370 1.06/AV 1.06/1 /1A 200 22 12 3,0 1.18035450 1.06/BV 1.06/2 /2A 300 30 18 3,5 2.88035530 1.06/CV 1.06/3 /3A /4 300 36 28 6,5 5.08035610 1.06/DV 1.06/3 /3A /4 400 36 28 6,5 6.38035880 1.06/EV 1.06/3 /3A /4 500 36 28 6,5 7.58112700 1.06/D-300 1.06/5 320 50 35 11,0 5.78112890 1.06/D-400 1.06/5 420 50 35 11,0 6.48113860 1.06/D-500 1.06/5 520 50 35 11,0 8.4

1.06 Pulling hooksset of 2 pieces, rigid pattern


8036260 1.06/100 1.06/11 1.06/1A1 100 22 15 3,0 0.48111490 1.06/150 1.06/21 1.06/2A1 150 30 24 3,5 1.18036420 1.06/200 1.06/31 1.06/3A1 1.06/41 200 36 32 5,0 2.4

1.06 Pulling hooksset of 2 pieces, slim patternThe forged hook feet are very shallow and thus particularly suitable for barely-accessible places.

Code No. B b c d e f 0

1175513 1.06/S100 1.06/S1 1.06/S1A 100 27 6 3,6 13 0.51175548 1.06/S200 1.06/S1 1.06/S1A 200 27 6 3,6 13 1.01175556 1.06/S250 1.06/S1 1.06/S1A 250 27 6 3,6 13 1.21554840 1.06/S100S 1.06/S1 1.06/S1A 100 27 6 2,3 13 0.51554859 1.06/S200S 1.06/S1 1.06/S1A 200 27 6 2,3 13 1.01554867 1.06/S250S 1.06/S1 1.06/S1A 250 27 6 2,3 13 1.21175564 1.06/S150 1.06/S2 1.06/S2A 150 40 8 5,0 17 1.31175572 1.06/S220 1.06/S2 1.06/S2A 220 40 8 5,0 17 1.71175580 1.06/S300 1.06/S2 1.06/S2A 300 40 8 5,0 17 2.2

1.06 Fast clamping pulling hooksset of 2 piecesWith the innovative high-speed clamps, fast and uncomplicated setting-up and readjustment is child's play.


1221213 1.06/A-E 1.06/1-E 1.06/1A-E 100 22 12 3,0 0.61221221 1.06/B-E 1.06/2-E 1.06/2A-E 150 30 18 3,5 1,61221248 1.06/C-E 1.06/3-E 1.06/3A-E 200 36 28 6,5 3.5


320

1.06 AS Puller set2-arm pattern with 6 slim hooksWith very slim forged hooks, thus particularly suitable for barely-accessible places.

Code No. Contents 2 each 0

8001710 1.06/AS 1.06/S100 S200 S250 3.3

1.06 Puller setwith display stand

Code No. B 0

8111570 1.06/ST 1.06/1 /1A /2 /2A /3 17.58111650 1.06/ST1 1.06/11 /1A1 /21 /2A1 /31 15.01322745 1.06/ST-E 1.06/1-E /1A-E /2-E /2A-E /3-E 20.0

1.07 Universal puller3-arm patternFor use as internal or external puller. The even load distribution on the three pulling hooks guarantees secure grip and central pulling. Hooks in special lengths available. Hooks 1.07/AV (clamping reach 200 mm) for 1.07/1 and 1.07/1A, and hooks 1.07/BV (clamping reach 300 mm) for 1.07/2 and 1.07/2A. Spindle may be exchanged for hydraulic pressure spindle (see table).


8113940 1.07/1 90 70 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.48114080 1.07/1A 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.68114160 1.07/2 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.68114240 1.07/2A 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.01541757 1.07/3 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0


321

1.07 Universal puller3-arm pattern, with slim hooksThe feet of the hooks are very slim and particularly suitable for barely-accessible places.

Code No. a b A $ c d e f max. t 0

8116450 1.07/S1 90 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.38116530 1.07/S1A 130 100 M 14x1,5 x 140 17 27 6 3,6 13 2,5 1.48116610 1.07/S2 160 150 G 1/2 x 210 22 40 8 5,0 17 5,0 3.68116880 1.07/S2A 200 150 G 1/2 x 210 22 40 8 5,0 17 5,0 4.0

1.07 Universal puller3-arm pattern, with rigid hooksDesign as universal puller No. 1.07/1 to 1.07/3, but with rigid pulling hooks. For greater ease in setting the clamping spread. The hooks clamp automatically when under tension. The hooks may be reversed to convert the puller from an external one to an internal one. Spindle may be exchanged for hydraulic pressure spindle (see table).


1305549 1.07/11 90 70 140 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.31306022 1.07/1A1 130 80 180 100 M 14x1,5 x 140 17 22 15 4,0 3,0 1.51306154 1.07/21 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.01306278 1.07/2A1 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 24 3,5 5,0 3.21554778 1.07/31 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0

1.07/4 Universal puller3-arm patternJust like our standard model No. 1.06, this puller is designed for all branches of industry, but particularly for the construction of electric motors. It is also suitable for removing heavy, multistage pulley wheels, flywheels, gear wheels, etc. Pins are used to lock the arms at 120° to each other on the hub. The clamping reach may be extended to 490 mm by using extensions No. 1.07/CV, 1.07/DV and 1.07/EV. Spindle may be exchanged for hydraulic pressure spindle (see table). This puller may also be used with the hydraulic aid 1.50 without requiring any reduction bushing.

Code No. a1 a2 b A Hydraulic spindle $ c d e max. t 0

8002440 1.07/4 450 530 200 G 1 x 360 1.06/HSP3 36 36 28 6,5 10 19.0


322

1.07 HSP Universal pullerhydraulic, 3-arm patternThe tried and tested model for the removal of pulleys, wheels, ball bearings, etc. Drop forged pattern. By reversing the hooks, this tool may be used as an internal or external puller. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


8009960 1.07/2-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 4.48010970 1.07/2A-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.81554816 1.07/3-HSP2 250 100 80 1.06/HSP2 36 28 6,5 7,5 9.38012400 1.07/4-HSP3 450 530 80 1.06/HSP3 36 28 6,5 10,0 19.4

1.07 HSP Fast clamping pullerhydraulic, 3-arm patternWith the hydraulic spindle, a controlled and safe pulling action is possible at all times. With the innovative high-speed clamps, fast and uncomplicated setting-up and readjustment is child's play.


1221922 1.07/2-E-HSP1 160 220 75 1.06/HSP1 30 18 3,5 5,0 4.51222554 1.07/2A-E-HSP1 200 260 75 1.06/HSP1 30 18 3,5 5,0 4.71554824 1.07/3-E-HSP2 250 400 80 1.06/HSP2 36 28 6,5 7,5 9.3

1.07 Fast clamping puller3-arm pattern, with fast-clamp adjustmentMay be used as an internal or external puller. The even distribution of the loading over the three hooks results in secure grip and centered pulling action. With the innovative high-speed clamps, fast and uncomplicated setting-up and readjustment is child's play. Spindle may be exchanged for hydraulic pressure spindle (see table).


1222902 1.07/1-E 90 70 140 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.41225901 1.07/1A-E 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.61227335 1.07/2-E 160 100 220 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 3.61227459 1.07/2A-E 200 100 260 150 G 1/2 x 210 1.06/HSP1 22 30 18 3,5 5,0 4.01554751 1.07/3-E 250 100 400 200 G 3/4 x 280 1.06/HSP2 27 36 28 6,5 7,5 9.0


323

1.07 Extension for pullersset of 3 piecesThe one-piece drop forged extensions enable the clamping reach to be extended. The extensions may be used together with all hooks of the 1.07 range.

Code No. B b 0

1307576 1.07/V100 for 1.07/A and 1.07/100 100 0.41307584 1.07/V150 for 1.07/B and 1.07/150 150 1.61307592 1.07/V200 for 1.07/C and 1.07/200 200 2.6

1.07 Pulling hooksset of 3 pieces


1307401 1.07/A 1.07/1 1.07/1A 100 22 12 3,0 0.91307428 1.07/B 1.07/2 1.07/2A 150 30 118 3,5 2.41307436 1.07/C 1.07/3 1.07/4 200 36 28 6,5 5.21307452 1.07/A-E 1.07/1 1.07/1A 100 22 12 3,0 0.91307460 1.07/B-E 1.07/2 1.07/2A 150 30 18 3,5 0.91307479 1.07/C-E 1.07/3 1.07/4 200 36 28 6,5 8.01307487 1.07/AV 1.07/1 1.07/1A 200 22 12 3,0 1.61307495 1.07/BV 1.07/2 1.07/2A 300 30 18 3,5 4.21307509 1.07/CV 1.07/3 1.07/4 300 36 28 6,5 7.51307517 1.07/DV 1.07/3 1.07/4 400 36 28 6,5 9.41307525 1.07/EV 1.07/3 1.07/4 500 36 28 6,5 11.2

1.07 Pulling hooksset of 3 pieces, rigid patternfor 3-arm pullers.


1307533 1.07/100 1.07/11 1.07/1A1 100 22 15 3,0 0.61307541 1.07/150 1.07/21 1.07/2A1 150 30 24 3,5 1.61307568 1.07/200 1.07/3 1.07/4 200 36 32 5,0 3.7

1.07 Pulling hooksset of 3 pieces, slim patternThe feet of the hooks are very slim and thus particularly suitable for barely-accessible places.

Code No. B b c d e f 0

1307606 1.07/S100 1.07/S1 1.07/S1A 100 27 6 3,6 13 1.21307622 1.07/S200 1.07/S1 1.07/S1A 200 27 6 3,6 13 2.41307630 1.07/S250 1.07/S1 1.07/S1A 250 27 6 3,6 13 3.01554786 1.07/S100S 1.07/S1 1.07/S1A 100 27 6 2,3 13 0.81554794 1.07/S200S 1.07/S1 1.07/S1A 200 27 6 2,3 13 1.61554808 1.07/S250S 1.07/S1 1.07/S1A 250 27 6 2,3 13 2.01307649 1.07/S150 1.07/S2 1.07/S2A 150 40 8 5,0 17 2.71307657 1.07/S220 1.07/S2 1.07/S2A 220 40 8 5,0 17 3.41307665 1.07/S300 1.07/S2 1.07/S2A 300 40 8 5,0 17 5.0

1.07/A-E

1.07/AV

1.07/A


324

1.07/KSE Puller setContents: case, spindle, 1 cross piece each 2-arm and 3-arm pattern and 3 puller hooks length 100 mm.

Code No. 0

1438484 1.07/K-1-SE 2.1

1.07 AS Puller set3-arm pattern with 9 slim hooksThe feet of the hooks are very slim and thus particularly suitable for barely-accessible places.


8117260 1.07/AS 1.07/S100 S200 S250 4.3

1.07 K Puller setwith 9 hooks, in plastic caseContents: case, spindle, 1 cross piece each 2-arm and 3-arm pattern and 9 puller hooks in length 100, 200, 250 mm.

Code No. amax b1 b2 b3 A $ c d e 0

8117340 1.07/K 120 100 200 250 M 14x1,5 x 140 17 27 6 3,6 5.0

1.07 Puller setin plastic caseWith three quick-clamping hooks and hydraulic spindle. Suitable for internal and external pulling work, 2-arm or 3-arm, with powerful hydraulic spindle and quick-clamping hooks. The right puller for the job - and ready in a second. The best equipment for the professional for everyday heavy duty work. For industrial or car and truck repairs - set of two. Your price advantage: 1 spindle and 2 hooks saved. Hydraulic spindle HSP1 (max. 12 t force). Three quick-clamping hooks for internal and external use. Heavy duty cross pieces for 2-arm or 3-arm use. And everything stored safely in a handy case. Contents: case, spindle, 1 cross piece each 2-arm and 3-arm, 3 puller hooks.

Code No. a1 a2 b A $ c d e 0

1438492 1.07/K-2-E-HSP1 160 220 75 1.06/HSP1 30 18 3 5 2.1


325

1.11 Puller3-arm patternThe reliable, heavy-duty model for the removal of pulleys, wheels, ball bearings, etc. The double hook ends, wide or narrow, grip automatically. The wide hook ends of the puller 1.10/2 and 1.11/2 possess 8 mm slots, so that pulleys or gears may also be pulled off using 8 mm bolts.

Code No. amax b A $ c1 c2 d e max. t 0

8002950 1.11/1 90 80 M 14x1,5 x 125 17 17 10 7 2 3,0 0.98003090 1.11/2 160 130 M 18x1,5 x 170 19 24 20 13 3 7,5 2.7

1.10 Puller2-arm patternThe reliable, heavy duty model for the removal of pulleys, wheels, ball bearings, etc. The double hook ends, wide or narrow, grip automatically. The wide hook ends of the puller 1.10/2 and 1.11/2 possess 8 mm slots, so that pulleys or gears may also be pulled off using 8 mm bolts.

Code No. amax b A $ c1 c2 d e max. t 0

8002600 1.10/1 90 80 M 14x1,5 x 125 17 17 10 7 2 2 0.78002790 1.10/2 160 130 M 18x1,5 x 170 19 24 20 13 3 5 2.0

1.08 Universal puller2-arm pattern, with fast spindle adjustmentTwice as fast and twice as simple. With the fast spindle adjustment feature, the spindle can be set the desired range in a moment. When the clamping yoke is released, the 4-part internal thread closes, and takes the full working pressure.

Code No. a1 a2 min a2 max b A $ c d e max. t 0

8019090 1.08/1A 130 80 180 100 M 14x1,5 x 140 17 22 12 3,0 3,0 1.48000070 1.08/2A 200 110 260 150 G 1/2 x 210 22 30 18 3,5 5,0 3.88018950 1.08/3A 350 130 420 200 G 3/4 x 280 27 36 28 6,5 7,5 10.2


326

1.13 Puller3-arm patternHandy robust model for the removal of pulleys, wheels, ball bearings, etc. Inexpensive economy model. The hook tips grip automatically.

Code No. amax b A $ c d e max. t 0

8004140 1.13/0 70 80 M 12x1,5 x 110 14 14 8 2,0 1,5 0.58004220 1.13/1 90 120 M 14x1,5 x 155 17 18 11 2,5 3,0 1.08004300 1.13/2 130 160 M 18x1,5 x 200 19 25 14 3,0 7,5 2.68004490 1.13/3 180 200 G 1/2 x 250 22 32 20 3,5 12,0 5.1

1.12 Battery-terminal puller2-arm patternThe perfect tool for removing small parts such as battery terminals, pulleys, wheels, ball bearings, etc. The hook tips grip automatically.

Code No. amax b A c d e max. t /

8003760 1.12/01 60 60 M 10x1,5 x 80 10 5 2 0,5 1608003840 1.12/02 60 40 M 10x1,5 x 60 10 5 2 0,5 120

1.12 Puller2-arm patternHandy robust model for the removal of pulleys, wheels, ball bearings, etc. Inexpensive economy model. The hook tips grip automatically.


8003250 1.12/0 70 80 M 12x1,5 x 110 14 14 8 2,0 1 0.48003330 1.12/1 90 120 M 14x1,5 x 155 17 18 11 2,5 2 0.78003410 1.12/2 130 160 M 18x1,5 x 200 19 25 14 3,0 5 1.98003680 1.12/3 180 200 G 1/2 x 250 22 32 20 3,5 8 3.7


327

1.13 Battery-terminal puller3-arm patternThe perfect tool for removing small parts such as battery terminals, pulleys, wheels, ball bearings, etc. The hook tips grip automatically.

Code No. amax b A c d e max. t /

8004570 1.13/01 60 60 M 10x1,5 x 80 10 5 2 0,75 2008004650 1.13/02 60 40 M 10x1,5 x 60 10 5 2 0,75 150

1.14 HSP Pullerhydraulic, 2-arm patternThe reliable, extra-strong model for the removal of pulleys, wheels, ball bearings, etc. With technical and economical benefits due to the variable clamping reach and automatic grip of the hooks. Especially suited to removing V-belt pulley wheels and flywheels mounted on longer shafts. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


1392883 1.14/3-HSP1 250 260 1.06/HSP1 22 32 18 3,5 8 4.31392913 1.14/4-HSP1 280 390 1.06/HSP1 22 32 20 3,5 8 5.1

1.14 Puller2-arm patternThe reliable, extra-strong model for the removal of pulleys, wheels, ball bearings, etc. With technical and economical benefits due to the variable clamping reach and automatic grip of the hooks. Especially suited to removing V-belt pulley wheels and flywheels mounted on longer shafts. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. amax b A Hydraulic spindle $ c d e max. t /

8004810 1.14/0 90 100 M 12x1,5 x 110 14 14 9 2,0 1 5008005030 1.14/1 130 140 M 14x1,5 x 140 17 18 11 2,0 2 8008005380 1.14/2 200 210 M 18x1,5 x 200 19 25 16 3,0 5 21008005460 1.14/3 250 260 G 1/2 x 250 1.06/HSP1 24 32 18 3,5 8 43008005540 1.14/4 280 390 G 1/2 x 250 1.06/HSP1 24 32 20 3,5 8 51008005620 1.14/5 420 480 G 1/2 x 350 1.06/HSP1 24 32 20 3,5 8 5800


328

1.15 HSP Pullerhydraulic, 3-arm patternThe reliable, extra-strong model for the removal of pulleys, wheels, ball bearings, etc. With technical and economical benefits due to the variable clamping reach and automatic grip of the hooks. Especially suited to removing V-belt pulley wheels and flywheels mounted on longer shafts. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


1392956 1.15/3-HSP1 250 260 1.06/HSP1 22 32 18 3,5 12 6.11392980 1.15/4-HSP1 280 390 1.06/HSP1 22 32 20 3,5 12 7.1

1.14 L Fan puller2-arm patternThe especially-slender hooks reach through the slots the collar of the fan. Due to their slender hooks and the three adjustment positions of its clamping reach, these pullers are also particularly suitable for the dismantling of gear arrangements. Hooks grip automatically.


8005110 1.14/1L 150 200 M 14x1,5 x 155 17 10 6 2 2 0.9

1.15 Puller3-arm patternThe reliable, extra-strong model for the removal of pulleys, wheels, ball bearings, etc. With technical and economical benefits due to the variable clamping reach and automatic grip of the hooks. Especially suited to removing V-belt pulley wheels and flywheels mounted on longer shafts. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. amax b A Hydraulic spindle $ c d e max. t /

8006000 1.15/0 90 100 M 12x1,5 x 110 14 14 9 2,0 2 6508006190 1.15/1 130 140 M 14x1,5 x 140 17 18 11 2,0 3 11008006350 1.15/2 200 210 M 18x1,5 x 200 19 25 16 3,0 8 29008006430 1.15/3 250 260 G 1/2 x 250 1.06/HSP1 24 32 18 3,5 12 61008006510 1.15/4 280 390 G 1/2 x 250 1.06/HSP1 24 32 20 3,5 12 71008006780 1.15/5 420 480 G 1/2 x 350 1.06/HSP1 24 32 20 3,5 12 8200


329

1.16 Puller2-arm patternVery strong type. Especially suitable for industrial purposes and for heavy agricultural and construction machines. Hooks grip automatically. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. amax b A Hydraulic spindle $ c d e max. t 0

8007080 1.16/1 280 300 G 1 x 360 1.06/HSP3 36 32 19 3 8 8.08007160 1.16/2 420 420 G 1 x 500 1.06/HSP3 36 32 22 3 8 10

1.15 L Fan puller3-arm patternThe especially-slender hooks reach through the slots the collar of the fan. Due to their slender hooks and the three adjustment positions of its clamping reach, these pullers are also particularly suitable for the dismantling of gear arrangements. Hooks grip automatically.


8006270 1.15/1L 150 200 M 14x1,5 x 155 17 10 6 2 3 1.3

1.16 HSP Pullerhydraulic, 2-arm patternVery strong type. Especially suitable for industrial purposes and for heavy agricultural and construction machines. Hooks grip automatically. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


8012590 1.16/1-HSP3 280 190 1.06/HSP3 36 32 19 3 8 9.38012670 1.16/2-HSP3 420 310 1.06/HSP3 36 32 22 3 8 11.3


330

1.17 Puller3-arm patternVery strong type. Especially suitable for industrial purposes and for heavy agricultural and construction machines. Hooks grip automatically. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. amax b A Hydraulic spindle $ c d e max. t 0

8007320 1.17/1 300 300 G 1 x 360 1.06/HSP3 36 32 19 3 12 9.78007400 1.17/2 425 425 G 1 x 500 1.06/HSP3 36 32 22 3 12 13.2

1.17 HSP Pullerhydraulic, 3-arm patternVery strong type. Especially suitable for industrial purposes and for heavy agricultural and construction machines. Hooks grip automatically. With the hydraulic spindle, a controlled and safe pulling action is possible at all times.


8014290 1.17/1-HSP3 300 190 1.06/HSP3 36 32 19 3 12 118014370 1.17/2-HSP3 425 315 1.06/HSP3 36 32 22 3 12 14.5

1.18 Puller ECO2-arm patternThe tried and tested range for economical bearing removal.


1464965 1.18/1 110 110 M 14x1,5 x 163 17 17 18 5,0 2 1.01464973 1.18/2 160 140 M 18x1,5 x 215 19 21 20 6,5 3 1.91464981 1.18/3 200 200 G 1/2 x 282 22 22 22 7,5 5 2.3


331

1.19 Puller ECO3-arm patternThe tried and tested range for economical bearing removal.


1465007 1.19/1 110 110 M 14x1,5 x 163 17 17 18 5,0 2 1.31465015 1.19/2 160 140 M 18x1,5 x 215 19 21 20 6,5 3 2.51465023 1.19/3 200 200 G 1/2 x 282 22 22 22 7,5 5 4.0

1.20 Pullerwith clamping yokeThese pullers are mainly employed for removing car and truck steering arms. The clamping yoke presses the hooks firmly behind the part to be removed and prevents the puller from slipping out of position.


8008050 1.20/1 90 85 M 18x1,5 x 130 19 22 12 3,0 5,0 1.28008130 1.20/2 90 100 M 18x1,5 x 130 19 24 15 3,0 5,0 1.88008210 1.20/3 150 140 G 1/2 x 175 22 30 18 3,5 7,5 3.3

1.22 Pullerwith clamping yokeDue to its double-ended hooks, this tool is particularly suitable for separating and removing flush-seated parts, such as axle bearings, pinions, etc. Especially economical, this is a multi-functional tool to cover a range of sizes.


8009020 1.22/1 110 170 M 18x1,5 x 200 19 25 14 3,5 5,0 2.18009100 1.22/2 160 260 G 1/2 x 350 22 25 14 3,5 7,5 4.18009290 1.22/3 160 325 G 1/2 x 350 22 25 14 3,5 7,5 4.5


332

1.23 Pullerwith slim hooksFor removing bearings in confined spaces. The scissor-pattern hook design means that the hooks are pressed firmly onto the part during the removal procedure.


8084580 1.23/1S 80 85 M 10 x 105 12 11 4,5 2,5 1,5 0.48084310 1.23/1 80 85 M 10 x 105 12 23 4,5 2,5 2,0 0.48084660 1.23/2 120 120 M 14x1,5 x 130 17 31 5,0 3,5 3,5 0.88084740 1.23/3 120 150 M 14x1,5 x 205 17 31 5,0 3,5 3,5 1.0

1.26 Nut splitterFor splitting jammed or stripped nuts without damaging the bolt thread. Suitable for nuts up to property class 6.

Code No. for nuts up to A $ 0

8009880 1.26/1 SW 17, M 10 M 14x1,5 x 37 17 0.28009610 1.26/2 SW 24, M 16 M 14x1,5 x 37 17 0.38010030 1.26/3 SW 36, M 24 M 22x1,5 x 70 24 1.0

1.26/12 Nut splitter setIn plastic wallet.


8010110 1.26/12 1.26/1 1.26/2 0.5

1.26 HYD Nut splitterhydraulicWith strong chisel, additionally induction hardened at the cutting edge for breakage resistance. The chamfer at the chisel's edge improves the splitting effect and prevents breakage. With smooth chisel function. Channel walls rolled, thus mirror-smooth and wear resistant. No force necessary when turning back the chisel. For nuts up to property class 10.

Code No. for nuts up to max. t 0

8009450 1.26/1 HYD SW 7 - SW 22, M 4 - M 14 5 0.78009530 1.26/2 HYD SW 22 - SW 36, M 14 - M 24 13 3.8

1.28 Stud extractorFor inserting and removing studs. These tools will reliably grip even extremely short stud ends. Slim pattern.

Code No. u-Stud $ /

8010620 1.28/1 6-13 19 2308010700 1.28/2 8-19 19 3008010890 1.28/3 19-25 19 390

1.28/4 Stud extractorFor inserting and removing studs. These tools will reliably grip even extremely short stud ends.

Code No. u-Stud $ /

1465031 1.28/4 5-26 19 390


333

1.29 Ball bearing extractorThese special extractors have been developed for removing ball bearings that are both on a shaft and in a housing. These hooks selected using the table are inserted into the ball race, evenly distributed in the outer ring according to the number of balls. The support rings supplied for the ball bearings to be removed are placed on the bearings’ inner races. The bridge with spindle is then placed on the centering depression of the shaft and the spindle put under tension with the hooks.

Code No. A $ /

8011000 1.29/1 M 10 x 160 14 1508011190 1.29/2 M 12 x 195 14 2808011270 1.29/3 M 14 x 210 17 4208011350 1.29/4 M 18 x 230 19 7508011430 1.29/5 M 20 x 235 22 1100

1.29 Pulling hooksset of 4 pieces* Support rings are used for pulling these bearings.

Code No. y for bridge - for ball bearing No. /

8011510 1.29/10 145 1.29/1 - 6000 6001 6002 808011780 1.29/15 145 1.29/1 - 6003 6004 6005 6200 6201 6202 1008011860 1.29/20 177 1.29/2 - 6006 6203 200

8011940 1.29/25 177 1.29/2 - 6007 6008 6009 60106204 6205 6300 6301 6302 200

8012080 1.29/30 1851.29/2 - 6303 6304

1.29/3 - 6011 6012300

8012160 1.29/35 187 1.29/3 - 6206 6207 6208 6305 4008012240 1.29/40 235 1.29/4 - 6209 6210 600

8110250 1.29/45 2361.29/4 - 6211 6212 6308* 6404 64051.29/5 - 6309* 6310* 6311* 6406* 800

1.29 K Ball bearing extractor setIn sheet metal case, dimensions: 285 x 190 x 75 mm.

Code No. Contents 0

8110330 1.29/1K3 hubs with spindle 1.29/1 - 1.29/36 sets hooks 1.29/10 - 1.29/351 plug-in handle 1.29/0

4.7

8012320 1.29/3K5 hubs with spindle 1.29/1 - 1.29/56 sets hooks 1.29/10 - 1.29/451 plug-in handle 1.29/0 and 4 support rings

8.0

Tool inventory at the professional fire brigade in Bochum.


334

1.92 Ball bearing extractor PLUSUsing the new BALDUR ball bearing extractor, the removal of shaft-mounted ball bearings in a housing is now possible without any problems. Due to its great degree of functionality combined with the simplified handling, this novel design makes a PLUS in effectiveness and productivity possible. This tool is distinguished by its extreme user-friendliness. The hooks are fixed in the slot. The self-locking arrangement means that the force applied is 100% utilised. Secure at all times against slipping off - and a straight pulling force for precise working. Suitable for more than 40 standard ball bearings up to 6311.* with supporting ring 6309** with supporting ring 6310*** with supporting ring 6311

Code No. Bearing Hook Head size

1553534 1.92/1

6000600160026003620062016202620360046005600663006301630260076008620460096010620563036304

10101010102020202020203030304040404040404040

1-71-41-31-41-41-71-41-41-31-31-31-31-31-71-31-31-41-31-31-31-71-7

1553542 1.92/2

6011601262066207630564036306630762086209621062116407*6404640564066308630962126310**6311***

505050505060606060606060607070707070707070

2-32-32-32-32-72-32-42-42-32-32-32-32-32-72-72-72-42-42-32-42-4

1553550 1.92/12Contents of set 1.92/1 and1.92/2


335

1.30 Internal extractorFor extremely-tightly-packed ball bearings, bearing races, bushings, and oil seals®. Operation:The internal extractor is inserted into the bearing and the spindle screwed in. The sharp turned-out shoulders of the pulling shell jaws will press outwards behind the part to be extracted. The counter-support brace is then added. Both feet must be aligned parallel to the spindle to ensure rigidity.

Code No. p C $ /

8012750 1.30/0 M 10 5-8 10 1508012830 1.30/1 M 10 8-12 10 1608012910 1.30/2 M 10 12-15 10 1708013130 1.30/3 M 10 15-19 14 1708013480 1.30/4 M 10 19-25 14 2008013560 1.30/4A M 10 25-30 14 3008013640 1.30/5 M 10 30-35 14 3508013720 1.30/6 M 14x1,5 35-45 17 6508013800 1.30/7 M 14x1,5 45-55 17 8008013990 1.30/8 M 14x1,5 55-70 19 14008014020 1.30/9 M 14x1,5 70-100 27 2900

1.30 N Internal extractorwith reinforced shoulderEspecially suitable for the safe and trouble-free extraction of needle roller bearings, ball bearings and brass sleeves from crankshafts. Note: The soulder of the shell jaw must be applied behind the bearing.

Code No. p C $ /

8013050 1.30/2N M 10 12-14 10 1708013210 1.30/3N M 10 14-19 14 170

1.30/10 Internal extractorSuitable for removing large ball bearings and bearing outer races. Operation:The extraction jaws are spread by turning the nut. The newly-developed spreading system enables a simple, step-free and time-saving adjustment to the desired diameter to be made. The sharp-edged sections of the extraction jaws seat flush beneath when spread.

Code No. p C $ /

8014100 1.30/10 G 1/2" 60-160 36 2450

1.35 Impact bearing pullerSuited for the removal of small ball bearings since there is often not enough room for support braces.

Code No. for internal extractor with adaptor p $ /

8016070 1.35/1 1.30/1 - 1.30/2 - M 10 17 5508039010 1.35/2 1.30/0 - 1.30/7 M 14 x 1,5 M 10 24 3200

1.35/2

1.35/1

1.30/0-9

1.30/2N


336

1.36 Support braceFor internal extractors Nos. 1.30/0 – 1.30/9. Operation:The support brace is placed on the housing and the spindle screwed onto the spindle of the internal extractor. The toggle is held firmly, and the bearing extracted by tightening the nut.

Code No. for internal extractor p $ /

8016580 1.36/1 1.30/1 - 1.30/5 M 10 27 6008016660 1.36/2 1.30/6 - 1.30/8 M 14x1,5 32 14008016740 1.36/3 1.30/9 M 14x1,5 32 3000

1.36/4 Support braceFor internal extractor No. 1.30/10. Operation see No. 1.36

Code No. for internal extractor p $ /

8016820 1.36/4 1.30/10 G 1/2" 36 7700

1.31 Internal extractor setThe handy sheet metal case contains the most used extractor sizes for the removal of ball bearings, bearing races, bushings, oil seals®, etc.

Code No. Contents 0

8014450 1.31/0N 4 internal extractors 12-30 mm 1.30/2 -3 -4 -4A1 support brace 1.36/1 2.4

8014530 1.31/0 4 internal extractors 12-30 mm 1.30/2N -3N -4 -4A1 support brace 1.36/1 2.4

8014610 1.31/1 6 internal extractors 12-46 mm 1.30/2 - 62 support braces 1.36/1 - 2 5.9

8014880 1.31/2 8 internal extractors 12-70 mm 1.30/2 - 82 support braces 1.36/1 - 2 10.0

1.32 Set of internal and external extractorsIn a handy sheet metal case. Sets comprise internal extractors, support braces, pulling chucks, external extractors and stud extractors.

Code No. Contents 0

8015260 1.32/1

6 internal extractors 12-46 mm 1.30/2 - 6

2 support braces 1.36/1 - 21 pulling chuck 1.44

1 battery-terminal puller 1.12/02

1 puller, 2-arm pattern 1.06/1

10.0

8015340 1.32/2

8 internal extractors 12-70 mm 1.30/2 - 82 support braces 1.36/1 - 2

1 pulling chuck 1.44

1 battery-terminal puller 1.12/022 pullers, 2-arm pattern 1.06/1 - 2

1 stud extractor 1.28/1

19.0

1.36/1-3

1.36/4

1.32/1

1.32/2


337

1.37 Cylinder liner pullercomplete with support braceWet heavy-vehicle (e.g. Daimler Benz, MAN) cylinder liners, automobile and stationary-engine liners, and other parts may be extracted using this puller. Operation:The spindle of the support brace is screwed into the clamping nut of the puller, and the puller inserted into the liner. The support brace is placed on to the cylinder block. Due to the newly-developed spreading system, when the spindle is turned, all three jaws spread quickly and without difficulty, until they are firmly seated beneath the edge of the liner. Then the nut of the support brace is tightened.

Code No. p C $ /

8017200 1.37/2 G 1/2" 60-160 36 6800

1.38 V Extension rodFor separator puller No. 1.38.

Code No. for separator p y 0

8018440 1.38/AV 1.38/0 1.38/1 M 10 100 0.28018520 1.38/CV 1.38/2 M 14 x 1,5 100 0.58018600 1.38/DV 1.38/3 M 18 x 1,5 100 0.68018790 1.38/EV 1.38/4 M 22 x 1,5 200 2.18018870 1.38/FV 1.38/5 M 24 x 1,5 200 2.7

1.38 Separator pullerThese separator pullers are used together with the bearing separators No. 1.40. The tension bolts are screwed into the threaded holes in the bearing separators.

Code No. for separator a b A $ p / p top Hydraulic spindle 0

8017550 1.38/0 1.40/0 40-120 160 M 14 x 120 17 M 10 / M 12x1,5 1.08017630 1.38/1 1.40/1 60-165 230 M 18 x 170 19 M 10 / M 14x1,5 2.48017710 1.38/2 1.40/2 70-215 250 G 1/2 x 210 22 M 14x1,5 / M 16x1,5 1.06/HSP1 3.88017980 1.38/3 1.40/3 90-300 270 G 3/4 x 280 27 M 18x1,5 / M 20x1,5 1.06/HSP2 7.28018010 1.38/4 1.40/4 125-380 350 G 1 x 310 36 M 22x1,5 / M 24x1,5 1.06/HSP3 11.38018280 1.38/5 1.40/5 140-440 400 G 1 x 360 36 M 24x1,5 / M 26x1,5 1.06/HSP3 16.3


338

1.38 HSP Separator pullerhydraulic, for separating bladesThese pullers are used together with the separating blades No. 1.40. The tension bolts are screwed into the threaded bores of the separating blades.

Code No. for separator a b p 0

8014960 1.38/2-HSP1 1.40/2 70-215 175 M 14 x 1,5 4.08015180 1.38/3-HSP2 1.40/3 90-300 195 M 18 x 1,5 6.88015420 1.38/4-HSP3 1.40/4 125-380 240 M 22 x 1,5 11.88015500 1.38/5-HSP3 1.40/5 140-440 290 M 24 x 1,5 16.6

Code No. for puller p O 0

8019680 1.40/0 1.38/0 M 10 5-60 0.48019760 1.40/1 1.38/1 M 10 12-75 1.08019840 1.40/2 1.38/2 M 14 x 1,5 22-115 2.38019920 1.40/3 1.38/3 M 18 x 1,5 30-155 4.48020180 1.40/4 1.38/4 M 22 x 1,5 30-200 8.98020260 1.40/5 1.38/5 M 24 x 1,5 30-250 15.3

1.41 Separator and puller setSet in sheet metal case, comprising separator, puller, and extension rods. Dimensions: 420 x 320 x 80 mm.

Code No. Contents 0

8109750 1.41/0 1.38/0 1.38/AV 1.40/0 2.88109830 1.41/1 1.38/1 1.38/AV 1.40/1 4.18109910 1.41/2 1.38/2 1.38/CV 1.40/2 9.18110090 1.41/3 1.38/3 1.38/DV 1.40/3 16.18110170 1.41/4 1.38/4 1.38/EV 1.40/4 28.6

1.40/15 Drive shaft bearing pullerOperation:The separator blades are placed evenly behind the bearing and the pulling arms aligned parallel to the axle and spindle.

Code No. Aperture y A $ 0

8010380 1.40/15 45-75 750 G 1/2 x 160 22 11.8

1.40/16 Set of hooks2 piecesThese hooks, together with the crossbeam and separator blades of No. 1.40/15, are used for mounting drive-shaft bearings.Operation:The separator blades are placed with the flat side behind the bearing, and the hooks inserted behind the clamping bolt of the separator blades. When the spindle is tightened, the bearing is pulled against the axle flange.

Code No. Description 0

8010460 1.40/16 1 pair hooks as illustrated 1.48010540 1.40/16A Crossbeam with spindle 2.2

1.40/16A

1.40/161.40/15


1.40 Bearing separatorFor removing taper roller and ball bearings, inner bearing races, and other tightly-seated or thin-walled parts. Operation:To remove tightly-seated parts, the sharp edges of the separator blades are pressed behind the part and it is then withdrawn using the correct puller No. 1.38. To avoid damage to delicate parts, the flat surfaces of the separator blades are used. This produces a large support surface that prevents deformation.

339

1.44 Pulling chuckFor removing the inner races of dynamos, magnetos, motors, and other machine parts. Simple operation by tightening the cap nut.

Code No. Clamping range mm Clamping reach mm 0

8022040 1.44/1 5-32 125 1.4

Forging of the heavy-duty puller crossbeams in the BALDUR works in Remscheid.

1.50 Hydraulic pump and cylinder setThis hydraulic set, consisting of hand pump 1.50/1 and hydraulic cylinder 1.51, is suitable for pressing, straightening, lifting, bending, and pulling.

Code No. consisting of: 0

8110410 1.50/10 Hydraulic hand pump 1.50/1Hydraulic cylinder 1.51/10 11.0

8110680 1.50/11 Hydraulic hand pump 1.50/1Hydraulic cylinder 1.51/11 13.0

1.50/1 Hydraulic hand pumpSupplied complete with 1.50 m high-pressure hose, to fit hydraulic cylinder 1.51.

Code No. for hydraulic cylinder 0

8022710 1.50/1 1.51/10 1.51/11 7.0

1.51 Hydraulic cylinderCode No. Stroke height mm max. t 0

8023440 1.51/10 140 10 4.08110760 1.51/11 200 10 6.0


340

1.06 Pullerfor hydraulic implement 1.50For the fast and damage-free removal of pulleys, wheels, ball bearings, etc. Robust pattern, designed for rigidity and heavy duty use. By reversing the hooks, this tool may be used as an internal or external puller. The reach may be increased both by using pulling hooks in special lengths, and by using extensions.

Code No. a1 a2 min a2 max b c d e max. t 0

8112620 1.06/40 520 185 600 200 36 28 6,5 10 11.08113000 1.06/50 640 230 715 225 50 33 10,0 18 24.0

1.15 H Pullerfor hydraulic implement 1.50Heavy duty pattern for the removal of gear wheels, spoked wheels, pulleys, etc. The hook tips grip automatically. The hooks may be moved to use this tool as a 2-arm puller. The adjustable reach means that this puller is very versatile.

Code No. amax b c d e max. t 0

8006860 1.15/30 250 260 32 18 3,5 12 9.08109590 1.15/40 280 390 32 20 3,5 12 9.5

1.17 H Pullerfor hydraulic implement 1.50Heavy duty pattern for the removal of gear wheels, spoked wheels, pulleys, etc. The hook tips grip automatically.

Code No. amax b c d e max. t 0

8007590 1.17/10 300 300 36 19 3,5 12 11.48109670 1.17/20 425 425 36 22 3,5 12 12.3


341

1.55 Hydraulic pressThis piece of auxiliary equipment considerably increases the capability of the standard pressure spindle. Operation:With pressure released, the press is placed between the pressure spindle and the end of the shaft. The pressure spindle is then tightened firmly. Care must be taken that the centreline of the shaft, the hydraulic press, and the pressure spindle are exactly in alignment. Then the hydraulic spindle is screwed inwards. Important note: Release the hydraulic press after use.

Code No. Stroke height mm Installed height mm max. t 0

8024090 1.55/1 10 75 8 0.78024170 1.55/2 15 90 15 1.3

1.60 Wheel-hub pullerFor cars and trucks with wheel stud circles up to 225 mm. Easy to use. With wheel stud protection using rotating nut apertures that always lie flat to the hub. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. No. of hooks A Hydraulic spindle 0

8024840 1.60/3 3 G 3/4 x 200 1.06/HSP2 4.08110840 1.60/5 4 G 3/4 x 200 1.06/HSP2 4.58024920 1.60/4 5 G 3/4 x 200 1.06/HSP2 5.08110920 1.60/H 1 spare hook 0.5

1.60 HSP Wheel-hub pullerhydraulicFor cars and trucks with wheel stud circles up to 225 mm. Easy to use. With wheel stud protection using rotating nut apertures that always lie flat to the hub.

Code No. No. of hooks A 0

8015690 1.60/3-HSP2 3 1.06/HSP2 4.68015770 1.60/4-HSP2 4 1.06/HSP2 5.18015850 1.60/5-HSP2 5 1.06/HSP2 5.6

1.61 Wheel-hub pullerFor cars and trucks with wheel stud circles up to 250 mm. Simple use. Just place the plate with the spindle on the centre-marking of the axle and fold back the hooks onto the plate. With swivelling nut holders always lying flat on the hub to prevent wheel-stud damage. Spindle may be exchanged for hydraulic pressure spindle (see table).


8111060 1.61/3 3 G 3/4 x 200 1.06/HSP2 5.08111140 1.61/4 4 G 3/4 x 200 1.06/HSP2 5.68025300 1.61/5 5 G 3/4 x 200 1.06/HSP2 6.28111220 1.61/H 1 spare hook 0.6

1.60/3

1.60/H

1.60/5-HSP2

1.61/5


342

1.61 HSP Wheel-hub pullerhydraulicFor cars and trucks with wheel stud circles up to 250 mm. Easy to use. With wheel stud protection using rotating nut apertures that always lie flat to the hub.

Code No. No. of hooks Hydraulic spindle 0

8015930 1.61/3-HSP2 3 1.06/HSP2 5.68016150 1.61/4-HSP2 4 1.06/HSP2 6.28016230 1.61/5-HSP2 5 1.06/HSP2 6.8

1.62 Wheel-hub pullerFor trucks with wheel stud circles up to 350 mm. Easy to use. With wheel stud protection using rotating nut apertures that always lie flat to the hub. This tool may also be used with the hydraulic aid without requiring a reduction bushing.


8026030 1.62/8 8 G 1 x 310 1.06/HSP3 10.58111220 1.61/H 1 spare hook 0.6

1.62 HSP Wheel-hub pullerhydraulicFor trucks with wheel stud circles up to 350 mm. Easy to use. With wheel stud protection using rotating nut apertures that always lie flat to the hub.

Code No. No. of hooks A 0

8016310 1.62/8-HSP3 8 1.06/HSP3 11.9

1.64 Drive shaft pullerSuitable for drive shafts with 4 or 5 apertures. For wheel stud circles 100-180 mm.Operation:The puller is attached to the drive shaft flange using the nuts of the wheel bolts. By striking the spindle head with the sliding hammer, the shaft may be removed easily and without damage.

Code No. p 0

8026700 1.64/1 max. M14 3.8

1.65 Pulling flangeThe flange possesses slots for hole pitches of 180, 120, and 90 degrees. Additional holes may be drilled to render the flange suitable for other pitches and aperture diameters. A very sturdy model for heavy parts and the highest requirements. Spindle may be exchanged for hydraulic pressure spindle (see table).

Code No. Stud , A Hydraulic spindle 0

8027000 1.65/1 up to 16 G 1 x 270 1.06/HSP3 16.3

1.62/8


343

1.66 Pulling flangeFor wheels and discs with tapped holes up to M10. The flange is fitted with slots for hole pitches of 180 and 120 degrees, and using one pair each of long and short hooks and a protective cap for the thread of the steering column, this tool is suitable as a steering wheel puller.

Code No. Stud , A $ 0

8027510 1.66/1 up to 10 M 12 x 110 14 0.7

8027780 1.66/11 with hooks in length 85 + 135 mm, 1 pair each M 12 x 110 14 1.0

1.67 Steering-wheel pullerSteering-wheel puller for cars. The puller includes one pair of short hooks, one pair of long hooks, and a protective cap for the thread of the steering column.

Code No. Clamping reach Hook length up to A $ 0

8028240 1.67/1 35-90 135 M 14x1,5 x 150 17 0.6

1.68 Steering-wheel pullerSteering-wheel puller featuring one pulling ring each with 100 mm and 150 mm diameter for 3-spoke and 4-spoke steering wheels. To protect the steering-wheels, the pulling rings are fitted with sliding rubber sleeves.

Code No. Hook length mm A $ 0

8028750 1.68/1 120 M 18 x 170 19 2.0

1.70 Dismantling and assembly forkThe wedge-shaped fork end makes the fast removal of track rod and push rod ends, steering arms, and other steering parts possible. Also suitable for removing shock absorbers and other separating and dismantling work. The forks are suitable for use in the most confined spaces. Hammer blows on the handle ends are used to separate the parts.

Code No. A mm B mm C mm 0

8029210 1.70/1 18 340 80 0.88029480 1.70/2 23 340 80 0.88029560 1.70/3 29 350 90 1.08029640 1.70/4 40 350 90 1.18085040 1.70/5 45 355 95 1.2


344

1.74 Universal ball joint pullerFor removing the ball joint journals on track rods, stabilizers, etc. Simple operation due to slender lower part and two-stage lever position.

Code No. O Clamping height Fork depth 0

8085200 1.74/1 20 12-50 35 1.08085390 1.74/2 20 50-80 35 1.4

1.75 Oil filter hook3-arm patternFor removing firmly seated oil filters.

Code No. O Drive 0

8117420 1.75/1 60-120 without adaptor G 3/8, with adaptor 17 mm external, G 1/2 internal 0.6

1.73 Universal ball joint pullerFor removing ball joints on cars and trucks.

Code No. O Clamping height Fork depth 0

8030810 1.73/1 23 65 24 0.78033240 1.73/3 32 85 28 2.4

1.72 Ball joint pullerFor the simple and damage-free removal of ball pins on track rods and push rods.

Code No. a b c A $ 0

8030300 1.72/1 18 35 40 M 14x1,5 x 50 17 0.38030490 1.72/2 23 45 50 M 14x1,5 x 50 17 0.58030570 1.72/3 27 56 60 M 18x1,5 x 80 19 0.78030650 1.72/4 37 78 75 G 1/2 x 110 22 1.5

1.76 Cartridge spanner3-arm patternFor removing firmly seated granulate cartridges.

Code No. O Drive 0

1523651 1.76/1 80-150 1/2" 0.6


345

1.78 P Universal coil spring compressorA coil spring compressor for MacPherson suspension strut and transverse link axles with spring diameters of 110-180 mm. Shock absorbers may be replaced without removing the suspension struts. The safety holder renders slipping impossible. VPA-GS-tested safety. The hooks are drop forged. The wide support rests are matched to the coil spring pitch.

Code No. Clamping reach mm max. t 0

8111300 1.78/P1 240 3,5 3.58031030 1.78/PK1 240 3,5 3.5

1.79 Spring spreaderThis has been especially designed for VAG exhaust installations, where the pipe is not held by bolts to the exhaust manifold, but clamped on using springs.

Code No. 0

8112540 1.79/1 0.4

1.78 S Safety coil spring compressorSafety coil spring compressor for the safe installation and removal of coil springs with a diameter of 110–180 mm. The spindles (M18) have 13 mm hexagon drive nut, so that when compressing the springs, they turn downwards, thus preventing damage to bodywork above the springs. Safety note: When the spindles are tightened evenly, the clamping heads grip the coils tightly, rendering sideways slip impossible. VPA-GS-tested safety.

Code No. Clamping reach mm 0

8031110 1.78/S1 180 2.28031380 1.78/S2 280 2.58031460 1.78/S3 380 2.8

d

1.78/P1

1.78/PK1

d


346

1.80/2 Spindle pressure padsfor axle bores (hollow shafts)See No. 1.80/1 for description.

Code No. Plate , Holder , 0

1120700 1.80/2

677073788390

545760647076

2.3

1.80/3 Spindle pressure padsfor axle bores (hollow shafts)See No. 1.80/1 for description.


1120719 1.80/3

41444850546064677073788390

32353841444850545760647076

4.2

1.81/1 Threaded insertsThe BALDUR threaded inserts make the removal of threaded caps, for example, possible, when these possess one threaded hole.For slide hammers 1.35/1, 1.35/2, threaded support 1.36/1.

Code No. Connecting / Insert thread /

1120727 1.81/1

M 10 - M 4M 10 - M 5M 10 - M 6M 10 - M 8M 10 - M 10M 10 - M 12

200

1.80/1 Spindle pressure padsfor axle bores (hollow shafts)The BALDUR pressure pads are used for the removal of such parts as bearings and gear wheels that are mounted on hollow shafts or in housings. Here, the spindle pressure pad serves as a counter-axis to the BALDUR puller, where the spindle now transfers the force to the pressure pad.


1120697 1.80/1

2528323541444850546064

1922252832353841444850

2.2

1.81/2 Threaded insertsSee No. 1.81/1 for description.For slide hammers 1.35/2, 1.36/2, threaded support 1.36/3.


1120743 1.81/2

M 14x1,5 - M 8M 14x1,5 - M 10M 14x1,5 - M 12M 14x1,5 - M 14M 14x1,5 - M 16M 14x1,5 - M 18

470


347

1.81/10 Threaded insertsfor 1-hole and 2-hole uses, 2 eachThe BALDUR threaded inserts make the removal of threaded caps, for example, possible, when these possess one or two threaded holes. For separator puller 1.38/0, 1.38/1.


1120735 1.81/10

M 10 - M 4M 10 - M 5M 10 - M 6M 10 - M 8M 10 - M 10M 10 - M 12Adaptor

460

1.81/20 Threaded insertsfor 1-hole and 2-hole uses, 2 eachSee No. 1.81/10 for description.For separator puller 1.38/2.


1120751 1.81/20

M 14x1,5 - M 8M 14x1,5 - M 10M 14x1,5 - M 12M 14x1,5 - M 14M 14x1,5 - M 16M 14x1,5 - M 18Adaptor

1010

1.85/1 Professional plastic bearing installation set

This sturdy plastic bearing installation set combines the advantages of the usual models in metal with the advantages of plastic. The impact-resistant plastic is handily light, but just as robust as the metal variants.Using this bearing installation set, which consists of 33 impact rings, more than 200 types of bearings may be re-installed effortlessly and without damage. The set is completed with three aluminium impact sleeves and a recoil-free bodywork hammer with nylon heads, all in a strong plastic case. This set guarantees that the installed bearings will suffer no damage that might have happened when working "metal to metal". No deformations of the bearing housings, sealing rings, or shafts.

Code No. Contents 0

1120778 1.85/1Impact rings 10-50 mm, for external Ø 26-110 mm,hammer 1,2 kg,case dimensions 450 x 360 x 140 mm

4.6

1.91 Tyre removing toolFor breaking the adhesion between truck tyres and wheel rims.

Code No. y 0

8032270 1.91 300 1.8

AdaptorThreaded insert


348

2.10 Automobile workshop setAdd-on systemClearly arranged module system, everything at hand on perforated wall-board.

Code No. Contents 0

1088696 2.10 as below stated 11.5

Code No. Description Qty.

1076469 106/103 Cross piece, 2-arm pattern, 140 mm 11076981 107/103 Cross piece, 3-arm pattern, 140 mm 11120514 106/A Pulling hook, 100 mm 31175343 106/S100 Pulling hook, slim pattern, 100 mm 38003840 1.12/02 Battery-terminal puller, 2-arm pattern 18009610 1.26/2 Nut splitter 18010700 1.28/2 Stud extractor 18029480 1.70/2 Dismantling and assembly fork 18030810 1.73/1 Universal ball joint puller 18117420 1.75/1 Oil filter hook 11120638 71010 Perforated board 11081616 1500 H 1 Hook 41081624 1500 H 2 Spring clamp 91081632 1500 H 3 Spring clamp 5

2.20 Truck workshop setAdd-on systemClearly arranged module system, everything at hand on perforated wall-board.

Code No. Contents 0

1088718 2.20 as below stated 14.0


1076612 106/2A03 Cross piece, 2-arm pattern, 260 mm 11077023 107/2A03 Cross piece, 3-arm pattern, 260 mm 11120530 106/B Pulling hook, 100 mm 31175475 106/S220 Pulling hook, slim pattern, 220 mm 31123947 106/BV Pulling hook, 300 mm 31084593 1.2106210 Spindle 18116100 1.06/HSP1 Hydraulic pressure spindle 18019840 1.40/2 Bearing separator 11120638 71010 Perforated board 11081616 1500 H 1 Hook 101081632 1500 H 3 Spring clamp 5

2.30 Industrial pulling setAdd-on systemFor the assembly of the tried and tested 1.06 and 1.07 versions. Using this set, you will be able to assemble more than 12 of the usual versions with high-speed clamping hooks, including hydraulic spindle, in seconds.

Code No. Contents 0

1393014 2.30 as below stated 17.5


1076469 106/103 Cross piece, 2-arm pattern, 140 mm 11076485 106/1A03 Cross piece, 2-arm pattern, 180 mm 11076590 106/203 Cross piece, 2-arm pattern, 220 mm 11076612 106/2A03 Cross piece, 2-arm pattern, 260 mm 11076981 107/103 Cross piece, 3-arm pattern, 140 mm 11077007 107/1A03 Cross piece, 3-arm pattern, 180 mm 11077015 107/203 Cross piece, 3-arm pattern, 220 mm 11077023 107/2A03 Cross piece, 3-arm pattern, 260 mm 11084488 1.1406140 Spindle 11084593 1.2106210 Spindle 18116100 1.06/HSP1 Hydraulic pressure spindle 11178199 106/A-E Pulling hook 31178253 106/B-E Pulling hook 31120638 71010 Perforated board 11081616 1500 H 1 Hook 121081624 1500 H 2 Spring clamp 41081632 1500 H 3 Spring clamp 6


349

2.40 Pulling set for construction machinesAdd-on systemFor the assembly of the robust and handy strap-pattern pulling tools 1.14 and 1.15. With this set, you will be able to assemble 10 of the usual flexible strap-pattern pulling tools from the range 1.14/1.15, including the new hydraulic spindle.

Code No. Contents 0

1393030 2.40 as below stated 24.5


1077856 114/204 Head 11077910 114/304 Head 11078054 115/204 Head 11078070 115/304 Head 11084569 1.1806200 Spindle 11084631 1.2106250 Spindle 18116100 1.06/HSP1 Hydraulic pressure spindle 11077821 114/201 Pulling hook, 210 mm 31077899 114/301 Pulling hook, 260 mm 31077953 114/401 Pulling hook, 390 mm 31077872 114/208 Strap 61077937 114/308 Strap 61120638 71010 Perforated board 11081616 1500 H 1 Hook 61081624 1500 H 2 Spring clamp 21081632 1500 H 3 Spring clamp 20

Code Accessories No. Qty.

1075225 Hexagon bolt M10 61075144 Hexagon bolt M12 121074946 Hexagon nut M10 61074954 Hexagon nut M12 121074431 Spring washer M10 61074458 Spring washer M12 12

3.01 Track alignment gaugeFor inside measurement. Suitable for all vehicle types. With simple, telescopic length adjustment. Immediate track-difference readings may be taken from the milimetre scale. Extensive measurement range from 835 to 1500 mm, and with extensions up to 2100 mm. Track difference measurable from 0–35 mm.Notes on Use:The vehicle to be tested must be standing on level ground. The front wheels must be set for running straight ahead and have the same tyre pressure. The play in the steering linkage must be removed by pressing the front wheels apart. The track alignment gauge must be set roughly at the axle centre-line between the front tyres in such a manner that the two chain ends contact the ground. The scale is set a “0“. The car is allowed to roll forward approx. one half turn of the wheel, until the chain ends again contact the ground. The track difference may then be read off on the scale.

Code No. Description Measurement range 0

8033080 3.01 Track alignment gauge 835-1500 2.08033160 3.01/V Extension for track alignment gauge 1500-2100 0.4

Dump truck at work.


2-arm pattern - farnell element14 · 2-arm pattern the new model for the safe and fast removal of...

Documents