1910 / 1920 rcs technical specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6...
TRANSCRIPT
![Page 1: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/1.jpg)
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
1910 / 1920 RCSTechnical
Specifications
Manual # 99906442
Revised 02-17-2021
Copyright © 2021 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
![Page 2: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/2.jpg)
ii
1910 / 1920 RCS - Manual # 99906442
Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well-ventilated area and wear gloves or wash your hands frequently when servicing. For more information go to www.P65Warnings.ca.gov. 70490167
70490167PROP 65BKS 5-29-18
ORANGE , BLACK AND WHITE3.27” 2.70”
CN
![Page 3: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/3.jpg)
iii
1910 / 1920 RCS - Manual # 99906442
Table of Contents
Section - 1 1
1910 - RCS Technical Specifications .............................................................................................................21910 - RCS Technical Specifications-Metric ..................................................................................................41910 - RCS Technical Specifications-Metric ..................................................................................................5
Section - 2 7
1910 - RCS Lifting Capacity Chart, K1 ..........................................................................................................81910 - RCS Lifting Capacity Chart, K2 ..........................................................................................................91910 - RCS Lifting Capacity Chart, K3 ........................................................................................................101910 - RCS Lifting Capacity Chart, K4 ........................................................................................................ 111910 - RCS Lifting Capacity Chart, K5 ........................................................................................................121910 - RCS Lifting Capacity Chart, K6 ........................................................................................................131910 - RCS Lifting Capacity Chart ...............................................................................................................14
Section - 3 15
Working pressure on Main-Relief Valve & Port-Relief Valves ......................................................................16Working pressure on Main-Relief Valve & Port-Relief Valves ......................................................................17Hydraulic Diagram PVG32 - Crane Functins, Control Valve Fixed and Variable Flow Pump ......................18Hydraulic Diagram - Danfoss PVG32, Single-Circuit Variable 7 fcts. RC (3 EXV: FJ + 2 EXV, Winch) ........................................................................................................19Hydraulic Diagram – Danfoss PVG32, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch) .........20Hydraulic Diagram - Stablilizer circuit – Overview .......................................................................................21Hydraulic Diagram - Stabilizer circuit – 2 fcts. ............................................................................................22Hydraulic Diagram - Stabilizer circuit – 2 fcts. + 2 available fcts..................................................................23Hydraulic Diagram - Stabilizer circuit – 4 fcts. ............................................................................................24Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. ................................................................25Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC..........................................................261920 RCS - Pressure Setting for Diagram, Fly-Jib 700 ...............................................................................27
Section - 4 29
1920 - RCS Technical Specifications ...........................................................................................................301920 - RCS Technical Specifications-Metric ................................................................................................32
Section - 5 35
1920 - RCS Lifting Capacity Chart, K1 ........................................................................................................361920 - RCS Lifting Capacity Chart, K2 ........................................................................................................371920 - RCS Lifting Capacity Chart, K3 ........................................................................................................381920 - RCS Lifting Capacity Chart, K4 ........................................................................................................391920 - RCS Lifting Capacity Chart, K5 ........................................................................................................401920 - RCS Lifting Capacity Chart, K6 ........................................................................................................411920 - RCS Lifting Capacity Chart K1 - K6 ..................................................................................................42
Section - 6 43
Dimension Sketch ........................................................................................................................................44Slewing Radius ............................................................................................................................................45Dimension Sketch for Truck-Mounted Loader ..............................................................................................46Lifting Height at Column ...............................................................................................................................47Dimension Sketch, Fixed Stabilizer Legs .....................................................................................................48Dimension sketch, swing-up stabilizer legs 30°- 60° (manual) ....................................................................50Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic) .......................................................52
![Page 4: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/4.jpg)
iv
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch, Internal Hose Routing ...................................................................................................54Stowed in Truck Body ..................................................................................................................................55Dimension Sketch for Connecting Link ........................................................................................................56Centers of Gravity ........................................................................................................................................57
![Page 5: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/5.jpg)
v
1910 / 1920 RCS - Manual # 99906442
![Page 6: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/6.jpg)
vi
1910 / 1920 RCS - Manual # 99906442
![Page 7: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/7.jpg)
Section - 1 1 1910 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Section - 11910 - RCS Technical Specifications
![Page 8: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/8.jpg)
Section - 1 2 1910 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Technical Specifications
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3Load moment ft-lb 131641 127301 124408 121514 118621 116451Hydraulic reach ft 20’8” 27’5” 34’6” 42’0” 49’3” 56’9”Hydraulic telescopic movement in 6’3” 12’11” 19’9” 27’0” 34’1” 41’3”
Lifting capacity, hydraulic lb-ft9283-14’1” 8996-14’1” 8622-14’5” 8269-14’9” 7960-15’1” 7651-15’1”
6439-20’4” 6152-20’6” 5821-20’8” 5535-21’0” 5270-21’3” 5027-21’8”
4653-27’2” 4344-27’3” 4057-27’7” 3815-27’10” 3594-28’3”
3440-34’1” 3153-34’5” 2911-34’9” 2712-35’1”
2580-41’8” 2337-41’11” 2139-42’2”
1985-48’11” 1786-49’4”
1544-56’5”
Lifting capacity, manual extensions
lb-ft3550 - 34’1”’ 2690 - 41.8”’ 2051-49’2” 1632-56’5” 1103-64’3”
Slewing torque, gross lb-ft 12989Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis in 7’4”Width in 8’2”Width with extra valves (int. hose routing) in 8’3’Length, no extra valves in 2’8”Length, with extra valves (hose guides) in 3’1”Length, with extra valves (int. hose routing) in 2’8”
Stabilizer spread, S1 (standard) in 15’1”
Stabilizer spread, S2 in 18’4”
Stabilizer spread, D in 21’2”
Minimum Chassis SpecsFront Axle Rating (GAWR) 12000 lb (5450 kg)Rear Axle Rating (GAWR) 21,000 lb (9530 kg)Resistance to Bending Moment 1,755,000 in-lb (20.225 kg-m)
Weights ± 5% because of tolerances for plate thickness
![Page 9: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/9.jpg)
Section - 1 3 1910 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers lb 3021 3309 3638 3936 4201 4410Stabilizers, S1 fixed lb 441Stabilizers, S1 swing-up lb 452Stabilizers, S1 hydr. swing-up lb 474Stabilizers, S2 fixed lb 518Stabilizers, S2 swing-up lb 529Stabilizers, S2 hydr. swing-up lb 551Stabilizers, D1 fixed lb 662Stabilizers, D swing-up lb 662Stabilizers, D1 hydr. swing-up lb 695Mounting kit, 4 bolts lb 121Mounting kit, 8 bolts lb 132Tank, excl. oil (fitted on loader) lb 99Manual Extensions lb 187 165 143 99 88Oil in loader (stowing position) lb 66 77 88 99 110 110
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. lb 132Stand-up controls (HS), direct valve control lb 154Top seat (TS) lb 198Top seat, ladder bl 441 extra valve, hose routing lb 88 121 143 165 187 2091 extra valve, int. hose routing lb 165 165 165 176 176 1872 extra valves, hose guides lb 132 165 198 232 265 2982 extra valves, int. hose routing lb 287 287 087 309 320 353Winch (1.5 t), single snatch block lb 386 386 386 386 386 397
Winch (1.5 t), double snatch block lb 375 375 375 375 375 386
Winch (2.5 t), single snatch block lb 441 441 441 441 441 451
Winch (2.5 t), double snatch block lb 430 430 430 430 430 441
High-pressure filiter lb 15
Oil cooler lb 55
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed ft-lb 19108S1, swing-up ft-lb 19108S1, hydr. swing-up ft-lb 19108S2, fixed ft-lb 19108S2, swing-up ft-lb 19108S2, hydr. swing-up ft-lb 19108D, fixed ft-lb 15287D, swing-up ft-lb 15287D, hydr. swing-up ft-lb 15287
Power consumption (oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure psi 4786Tank capacity (fitted on loader) gal 24
![Page 10: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/10.jpg)
Section - 1 4 1910 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Technical Specifications-Metric
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 18.2 17.6 17.2 16.8 16.4 16.1Hydraulic reach m 6.3 8.4 10.5 12.8 15 17.3Hydraulic telescopic movement mm 1930 3940 6040 8230 10390 12580
Lifting capacity, hydraulic kg-m4210-4.3 4080-4.3 3910-4.4 3750-4.5 3610-4.6 3470-4.6
2920-6.2 2790-6.3 2640-6.3 2510-6.4 2390-6.5 2280-6.6
2110-8.3 1970-8.3 1840-8.4 1730-8.5 1630-8.6
1560-10.4 1430-10.5 1320-10.6 1230-10.7
1170-12.7 1060-12.8 970-12.9
900-14.9 810-16
700-17.2
Lifting capacity, manual extensions
kg-m1610-10.4 1220-12.7 930-15 740-17.2 500-19.6
Slewing torque, gross kNm 17.6Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis mm 2250Width mm 2500Width with extra valves (int. hose routing) mm 2535Length, no extra valves mm 830Length, with extra valves (hose guides) mm 950Length, with extra valves (int. hose routing) mm 830
Stabilizer spread, S1 (standard) mm 4615
Stabilizer spread, S2 mm 5590
Stabilizer spread, D mm 6470
Minimum Chassis SpecsFront Axle Rating (GAWR) 12000 lb (5450 kg)Rear Axle Rating (GAWR) 21,000 lb (9530 kg)Resistance to Bending Moment 1,755,000 in-lb (20.225 kg-m)
![Page 11: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/11.jpg)
Section - 1 5 1910 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers kg 1370 1510 1650 1785 1905 2000Stabilizers, S1 fixed kg 200Stabilizers, S1 swing-up kg 205Stabilizers, S1 hydr. swing-up kg 215Stabilizers, S2 fixed kg 235Stabilizers, S2 swing-up kg 240Stabilizers, S2 hydr. swing-up kg 250Stabilizers, D1 fixed kg 300Stabilizers, D fixed kg 300Stabilizers, D1 hydr. swing-up kg 315Mounting kit, 4 bolts kg 55Mounting kit, 8 bolts kg 60Tank, excl. oil (fitted on loader) kg 45Manual Extensions kg 85 75 65 45 40Oil in loader (stowing position) kg 30 35 40 45 50 50
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. kg 60Stand-up controls (HS), direct valve control kg 70Top seat (TS) kg 90Top seat, ladder kg 201 extra valve, hose routing kg 40 55 65 75 85 951 extra valve, int. hose routing kg 75 75 75 80 80 852 extra valves, hose guides kg 60 75 90 105 120 1352 extra valves, int. hose routing kg 130 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 175 180
Winch (1.5 t), double snatch block kg 170 170 170 170 170 175
Winch (2.5 t), single snatch block kg 200 200 200 200 200 205
Winch (2.5 t), double snatch block kg 195 195 195 195 195 200
High-pressure filiter kg 7
Oil cooler kg 25
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed kN 85S1, swing-up kN 85S1, hydr. swing-up kN 85S2, fixed kN 85S2, swing-up kN 85S2, hydr. swing-up kN 85D, fixed kN 63D, swing-up kN 63D, hydr. swing-up kN 63
Power consumption (oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure Bar 365Tank capacity (fitted on loader) L 90
Weights ± 5% because of tolerances for plate thickness
![Page 12: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/12.jpg)
This page left intentionally blank
6
1910 / 1920 RCS - Manual # 99906442
![Page 13: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/13.jpg)
Section - 2 7 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
Section - 21910 - RCS Load Capacity Charts
![Page 14: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/14.jpg)
Section - 2 8 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K1
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490231
CAPACITY CHART1910 RCS K1
2-11-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
70490231
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 RCS K1
0CENTERLINE
3'3” 6'6” 9'11” 13'1” 16'5” 19'8” 23'0”(1m) (2m) (3m) (4m) (5m) (6m) (7m)
MOUNTINGSURFACE
0
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
3'3”
6'6”
9'11”
13'1”
16'5”
19'8”
23'0”
(1m)
(2m)
(3m)
(4m)
(5m)
(6m)
(7m)
26'3”(8m)
29'6”(9m)
134486100
92834210
64392920
LBKG
![Page 15: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/15.jpg)
Section - 2 9 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K2
70490232
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490232
CAPACITY CHART1910 - K2
2-11-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 RCS K2
0
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
3’3”(1m)
6’ 6”(2m)
9’11”(3m)
13’1”(4m)
16’5”(5m)
19’8”(6m)
23’0”(7m)
26’3”(8m)
29’6”(9m)
32’10”(10M
36’1”(11m)
132286000
89964080
61522790
46532110
LBKG
3’3”(1m)
6’ 6”(2m)
9’11”(3m)
13’1”(4m)
16’5”(5m)
19’8”(6m)
23’0”(7m)
26’3”(8m)
29’6”(9m)
![Page 16: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/16.jpg)
Section - 2 10 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K3
70490233
REVISIONS
REV ECO DESCRIPTION DATE BYNOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490233
CAPACITY CHART1910-K3
2-11-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 K3
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0
3'3”
6'6”
9'8”
13'3”
16'4”
19'7”
23'0”
(1m)
3'3”(1m)
(2m)
6'6”(2m)
(3m)
9'8”(3m)
(4m)
13'3”(4m)
(5m)
16'4”(5m)
(6m)
19'7”(6m)
(7m)
23'0”(7m)
26'2”(8m)
26'2”(8m)
29'5”(9m)
29'5”(9m)
32'8”(10m)
32'8”(10m)
36'1”(11m)
36'1”(11m)
42'7”(13m)
39'4”(12m) LB
KG
127875800
86223910
58212640
43441970
34401560
![Page 17: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/17.jpg)
Section - 2 11 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K4
70490234
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490234
CAPACITY CHART1910 RCS K4
2-11-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 RCS K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
6' 6”(2m)
13'1”(4m)
19'8”(6m)
26'3”(8m)
32'10”(10m)
39'4”(12m)
0
0
6'6”
13'1”
19'8”
(2m)
(4m)
(6m)
26'3”(8m)
32'10”(10m)
52'6”(16m)
45'11”(14m)
39'4”(12m)
91494150
121255500
55352510
40571840
31531430
25801170
82693750
LBKG
![Page 18: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/18.jpg)
Section - 2 12 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K5
70490235
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490235
CAPACITY CHART1910 RCS K5
2-12-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 RCS K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0
6' 6”
13'1”
19'8”
(2m)
6' 6”(2m)
(4m)
13'1”(4m)
(6m)
19'8”(6m)
26’3”(8m)
26'3”(8m)
32'10”(10m)
32'10”(10m)
52'6”(16m)
52'6”(16m)
59'0”(18m)
45'11”(14m)
45'11”(14m)
39'4”(12m)
39'4”(12m)
LBKG
120155450
79603610
52702390
38151730
29111320
23371060
1985900
![Page 19: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/19.jpg)
Section - 2 13 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart, K6
70490236
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXAN
ADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490236
CAPACITY CHART1910 RCS K6
2-12-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1910 RCS K6
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0
6'6”
13'1”
19'8”
(2m)
6'6”(2m)
(4m)
13'1”(4m)
(6m)
19'8”(6m)
26'3”(8m)
26'3”(8m)
32'10”(10m)
32'10”(10m)
52'6”(16m)
52'6”(16m)
59'0”(18m)
59'0”(18m)
65’7”(20m)
45'11”(14m)
45'11”(14m)
39'4”(12m)
39'4”(12m)
LBKG7231
3280
119055400
76513470
50272280
35941630
27121230
2139970
1786810
1544700
![Page 20: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/20.jpg)
Section - 2 14 1910 - RCS Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1910 - RCS Lifting Capacity Chart
K1
K6
K5
K4
K3
K2
lbsft
928314’1”
643920’4”
kgm
42104.3
29206.2
lbsft
899614’1”
615220’6”
465327’2”
355034’1”
kgm
40804.3
27906.3
21108.3
161010.4
lbsft
862214’5”
582120’8”
434427’3”
344034’1”
269041’8”
kgm
39104.4
24606.3
19708.3
156010.4
122012.7
lbsft
826914’9”
553521’0”
405727’7”
315334’5”
258041’8”
205149’2”
kgm
37504.5
25106.4
18408.4
143010.5
117012.7
93015.0.
lbsft
796015’1”
527021’3”
381527’10”
291134’9”
233741’11”
198548’11”
163256’5”
kgm
36104.6
23906.5
17308.5
132010.6
106012.8
90014.9
74017.2
lbsft
765115’1”
502721’8”
359428’3”
271235’1”
213942’4”
178649’2”
154456’5”
110364’3”
kgm
34704.6
22806.6
16308.6
123010.7
97012.9
81015.0
70017.2
50019.6
Lifting capacity without manual extensionsLifting capacity with manual extensions
![Page 21: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/21.jpg)
Section - 3 15 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Section - 31910 - RCS Hydraulics
![Page 22: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/22.jpg)
Section - 3 16 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Working pressure on Main-Relief Valve & Port-Relief Valves
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 385 5584
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 380 365 5511 5294
Jib cylinderUp A 380 365 5511 5294Down B 250 200 3626 2901
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 200 P 2901Left B P 200 P 2901
GrabOpen A P 250 P 3626Close B P 250 P 3626
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 390 5656
Down - -
Jib cylinderUp 405 5874
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 350 [bar] 5076 [PSI]HDL 300 [bar] 4351 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
IMT reserves the right to introduce improvements and modifications
![Page 23: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/23.jpg)
Section - 3 17 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Working pressure on Main-Relief Valve & Port-Relief Valves
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 345 5004
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 380 365 5511 5294
Jib cylinderUp A 380 365 5511 5294Down B 250 200 3626 2901
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 390 5656
Down - -
Jib cylinderUp 405 5874
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 350 [bar] 5076 [PSI]HDL 300 [bar] 4351 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 100 L/min 26.4 gpm
IMT reserves the right to introduce improvements and modifications
![Page 24: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/24.jpg)
Section - 3 18 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram PVG32 - Crane Functins, Control Valve Fixed and Variable Flow Pump
Fixed pump Variable pump
PVSKM
PVP
PVSKM
PVP
![Page 25: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/25.jpg)
Section - 3 19 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Danfoss PVG32, Single-Circuit Variable 7 fcts. RC (3 EXV: FJ + 2 EXV, Winch)
PVS
LX
A-PORTB1
A1
A-PORTB2
A2
A-PORTB3
A3
A-PORTB4
A4
A-PORTB5
A5
A-PORTB6
A6
LS
M
P
T PVP
PPVSKM
B
ARemote
controlled stabilizers
B7 / B5
A7 / A5
B1
M3
B A
M2 M1 A1
M M2 M1C2
V2 V1
C1
M
Optional
*) Optional
A-PORT
*)
*)
*)
*)Pst
A-PORTB5
A5
A-PORTB6
A6
A-PORT
A-PORT
*)
*)
*)
*)
B6
B5
A5A6
P2
C3
P1
C1
C2 C4
P2
C3
P1
C1
C2 C4
M M2 M1C2
V2 V1
C1
A5 B5 A6 B6
C2 C1
V2 V1
M
V1V2
C1C2
*) *)
*) *)
HPCO /
2) This A-port is connected to a sequence valve and subsequently the rod side of stabilizer cylinders
PVB32Note 2
V1 V2
D
C3
*)
1) The HPCO port is used for manual controlled stabilizers
Note 1
Notes:
A B
A1 B1PR P T
Pst
T stab. valve
This hose routing if the crane has RC controlled stabilizers
This hose routing if the crane has manual controlled stabilizers
![Page 26: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/26.jpg)
Section - 3 20 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram – Danfoss PVG32, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
PVS
LX
A-PORTB1
A1
A-PORTB2
A2
A-PORTB3
A3
A-PORTB4
A4
A-PORTB5
A5
A-PORTB6
A6
LS
M
P
T PVP
PPVSKM
B
ARemote
controlled stabilizers
B7 / B5
A7 / A5
B1
M3
B A
M2 M1 A1
M M2 M1C2
V2 V1
C1
M
Optional
*) Optional
A-PORT
*)
*)
*)
*)Pst
A-PORTB5
A5
A-PORTB6
A6
A-PORT
A-PORT
*)
*)
*)
*)
B6
B5
A5A6
P2
C3
P1
C1
C2 C4
P2
C3
P1
C1
C2 C4
M M2 M1C2
V2 V1
C1
A5 B5 A6 B6
C2 C1
V2 V1
M
V1V2
C1C2
*) *)
*) *)
HPCO /
2) This A-port is connected to a sequence valve and subsequently the rod side of stabilizer cylinders
PVB32Note 2
V1 V2
D
C3
*)
1) The HPCO port is used for manual controlled stabilizers
Note 1
Notes:
A B
A1 B1PR P T
Pst
T stab. valve
This hose routing if the crane has RC controlled stabilizers
This hose routing if the crane has manual controlled stabilizers
![Page 27: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/27.jpg)
Section - 3 21 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – OverviewPstTst
D
C55228
58496
58496D
C55228
A14 B14 A13 B13 A12 B12 A11 B11
55226 / 55
281
PT
A-PORT A-PORT A-PORTA-PORT
2 functions:
4 or 2 + 2 extra functions:
4 + 4 extra functions:
4 remote controlled functions:
P
P2
T
B
A
T2
T
1 0 2
P T
B A
(1) (0) (2)
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
55737
P
P2
T
B
A
T2
T
1 0 2
P T
B A
(1) (0) (2)
1 0 2
P T
B A
(0) (2)(1)
B
A
55738
P
P2
T
B
A
T2
T
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
55739
Extra remote controlled functions:
5054
8
V V1
C1 C2 C3 C4C
V
1 pcs. 597711 pcs. 590571 pcs. 61778
![Page 28: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/28.jpg)
Section - 3 22 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stabilizer circuit – 2 fcts.
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A12
A11B12
B11
A12
B12
A11
B11
T
Pst
T
![Page 29: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/29.jpg)
Section - 3 23 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stabilizer circuit – 2 fcts. + 2 available fcts.
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A14
A13
A12
A11
B14
B13
B12
B11
A14
B14
A13
B13
A12
B12
A11
B11
T
Pst
T
![Page 30: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/30.jpg)
Section - 3 24 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stabilizer circuit – 4 fcts.
D
CD
C
Crane functions
PVP
PVS
PVSKMP
T
/ HPCOPst
A14
A13
A12
A11
B14
B13
B12
B11
A14
B14
A13
B13
A12
B12
A11
B11
T
Pst
P
![Page 31: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/31.jpg)
Section - 3 25 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts.
C1 C2 C3
D1 D2 D3
D
CD
C
A11 B11
A12 B12
A13 B13
A14 B14
A15 B15
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
T
Pst
T
![Page 32: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/32.jpg)
Section - 3 26 1910 - RCS Hydraulics
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC
C1
C2
C3
C4
V
V1
C1 C2 C3
D1 D2 D3
D
CD
C
C
V
Note 1Note 2
C
V
Note 1Note 2
C
V
Note 1Note 2
C
V
Note 1Note 2
A
B
Crane functions
PVP
Remote controlled stabilizers
PVB32
PVSLX
PVSKM
Extra function
Extra function
Extra function
Extra function
Notes:1) Optional function2) Important: Apply loadcarrying safety valve onextra functions!
C4
C3
C2
C1
V1
V
![Page 33: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/33.jpg)
Section - 4 27 1920 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Section - 41920 - RCS Technical Specifications
![Page 34: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/34.jpg)
Section - 4 28 1920 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Technical Specifications
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3Load moment ft-lb 130917 127301 124408 121514 118621 116451Hydraulic reach ft 20’8” 27’5” 34’6” 42’0” 49’3” 56’9”Hydraulic telescopic movement in 6’3” 12’11” 19’9” 27’0” 34’1” 41’3”
Lifting capacity, hydraulic lb-ft9261-14’0” 8794-14’2” 8600-14’5” 8247-14’8” 7938-15’2” 7651-15’2”
6417-20’4” 6130-20’6” 5821-20’9” 5513-21’0” 5248-21’3” 5005-21’6”
4631-27’1” 4322-27’4” 4057-57’7” 3793-27’10” 3572-28’1”
3440-34’3” 3153-34’5” 2911-34’8” 2690-34’11”
2580-41’8” 2337-41’11” 2139-42’2”
1985-49’0” 1786-49’2”
1544-56’5”
Lifting capacity, manual extensions
lb-ft3550-34’1” 2690-41’8” 2051-49’2” 1632-56’5” 1103-64’3”
Slewing torque, gross lb-ft 12989Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis in 7’4”Width in 8’2”Width with extra valves (int. hose routing) in 8’3’Length, no extra valves in 2’8”Length, with extra valves (hose guides) in 3’1”Length, with extra valves (int. hose routing) in 2’8”
Stabilizer spread, S1 (standard) in 15’1”
Stabilizer spread, S2 in 18’4”
Stabilizer spread, D in 21’2”
Minimum Chassis SpecsFront Axle Rating (GAWR) 12000 lb (5450 kg)Rear Axle Rating (GAWR) 21,000 lb (9530 kg)Resistance to Bending Moment 1,755,000 in-lb (20.225 kg-m)
![Page 35: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/35.jpg)
Section - 4 29 1920 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers lb 3131 3440 3749 4046 4311 4520Stabilizers, S1 fixed lb 441Stabilizers, S1 swing-up lb 452Stabilizers, S1 hydr. swing-up lb 474Stabilizers, S2 fixed lb 518Stabilizers, S2 swing-up lb 529Stabilizers, S2 hydr. swing-up lb 551Stabilizers, D1 fixed lb 662Stabilizers, D swing-up lb 662Stabilizers, D1 hydr. swing-up lb 695Mounting kit, 4 bolts lb 121Mounting kit, 8 bolts lb 132Tank, excl. oil (fitted on loader) lb 99Manual Extensions lb 187 165 143 99 88Oil in loader (stowing position) lb 66 77 88 99 110 110
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. lb 132Stand-up controls (HS), direct valve control lb 154Top seat (TS) lb 198Top seat, ladder bl 441 extra valve, hose routing lb 88 121 143 165 187 2091 extra valve, int. hose routing lb 165 165 165 176 176 1872 extra valves, hose guides lb 132 165 198 232 265 2982 extra valves, int. hose routing lb 287 287 287 309 320 353Winch (1.5 t), single snatch block lb 386 386 386 386 386 397
Winch (1.5 t), double snatch block lb 375 375 375 375 375 386
Winch (2.5 t), single snatch block lb 441 441 441 441 441 451
Winch (2.5 t), double snatch block lb 430 430 430 430 430 441
High-pressure filiter lb 15
Oil cooler lb 55
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed ft-lb 19108S1, swing-up ft-lb 19108S1, hydr. swing-up ft-lb 19108S2, fixed ft-lb 19108S2, swing-up ft-lb 19108S2, hydr. swing-up ft-lb 19108D, fixed ft-lb 15287D, swing-up ft-lb 15287D, hydr. swing-up ft-lb 15287
Power consumption (oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure psi 4786Tank capacity (fitted on loader) gal 24
![Page 36: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/36.jpg)
Section - 4 30 1920 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Technical Specifications-Metric
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 18.1 17.6 17.2 16.8 16.4 16.1Hydraulic reach m 6.3 8.4 10.5 12.8 15 17.3Hydraulic telescopic movement mm 1930 3940 6040 8230 10390 12580
Lifting capacity, hydraulic kg-m4200-4.3 4070-4.3 3900-4.4 3750-4.5 3600-4.6 3470-4.6
2910-6.2 2780-6.3 2640-6.3 2500-6.4 2380-6.5 2270-6.6
2100-8.3 1960-8.3 1840-8.4 1720-8.5 1620-8.6
1560-10.4 1430-10.5 1320-10.6 1220-10.7
1170-12.7 1060-12.8 970-12.9
900-14.9 810-16
700-17.2
Lifting capacity, manual extensions
kg-m1610-10.4 1220-12.7 930-15 740-17.2 500-19.6
Slewing torque, gross kNm 17.6Slewing angle ° 400°Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis mm 2250Width mm 2500Width with extra valves (int. hose routing) mm 2535Length, no extra valves mm 830Length, with extra valves (hose guides) mm 950Length, with extra valves (int. hose routing) mm 830
Stabilizer spread, S1 (standard) mm 4615
Stabilizer spread, S2 mm 5590
Stabilizer spread, D mm 6470
Minimum Chassis SpecsFront Axle Rating (GAWR) 12000 lb (5450 kg)Rear Axle Rating (GAWR) 21,000 lb (9530 kg)Resistance to Bending Moment 1,755,000 in-lb (20.225 kg-m)
![Page 37: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/37.jpg)
Section - 4 31 1920 - RCS Technical Specifications
1910 / 1920 RCS - Manual # 99906442
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers kg 1370 1510 1650 1785 1905 2000Stabilizers, S1 fixed kg 200Stabilizers, S1 swing-up kg 205Stabilizers, S1 hydr. swing-up kg 215Stabilizers, S2 fixed kg 235Stabilizers, S2 swing-up kg 240Stabilizers, S2 hydr. swing-up kg 250Stabilizers, D1 fixed kg 300Stabilizers, D fixed kg 300Stabilizers, D1 hydr. swing-up kg 315Mounting kit, 4 bolts kg 55Mounting kit, 8 bolts kg 60Tank, excl. oil (fitted on loader) kg 45Manual Extensions kg 85 75 65 45 40Oil in loader (stowing position) kg 30 35 40 45 50 50
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. kg 60Stand-up controls (HS), direct valve control kg 70Top seat (TS) kg 90Top seat, ladder kg 201 extra valve, hose routing kg 40 55 65 75 85 951 extra valve, int. hose routing kg 75 75 75 80 80 852 extra valves, hose guides kg 60 75 90 105 120 1352 extra valves, int. hose routing kg 130 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 175 175 175 175 180
Winch (1.5 t), double snatch block kg 170 170 170 170 170 175
Winch (2.5 t), single snatch block kg 200 200 200 200 200 205
Winch (2.5 t), double snatch block kg 195 195 195 195 195 200
High-pressure filiter kg 7
Oil cooler kg 25
Max. Load on stabilizers (per stabilizer cylinder) Unit K1 K2 K3 K4 K5 K6
S1, fixed kN 85S1, swing-up kN 85S1, hydr. swing-up kN 85S2, fixed kN 85S2, swing-up kN 85S2, hydr. swing-up kN 85D, fixed kN 63D, swing-up kN 63D, hydr. swing-up kN 63
Power consumption (oil capacity) Unit K1 K2 K3 K4 K5 K6Working pressure Bar 365Tank capacity (fitted on loader) L 90
![Page 38: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/38.jpg)
This page left intentionally blank
32
1910 / 1920 RCS - Manual # 99906442
![Page 39: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/39.jpg)
Section - 5 33 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
Section - 51920 - RCS K1-K6 Load Capacity Charts
![Page 40: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/40.jpg)
Section - 5 34 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K1
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490221
CAPACITY CHART1920 RCS K1
2-5-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
70490221
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K1
KGLB
0CENTERLINE
3'3” 6'6” 9'11” 13'1” 16'5” 19'8” 23'0”(1m) (2m) (3m) (4m) (5m) (6m) (7m)
MOUNTINGSURFACE
0
92614200
64172910
156317090
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
3'3”
6'6”
9'11”
13'1”
16'5”
19'8”
23'0”
(1m)
(2m)
(3m)
(4m)
(5m)
(6m)
(7m)
26'3”(8m)
29'6”(9m)
![Page 41: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/41.jpg)
Section - 5 35 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K2
70490222
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490222
CAPACITY CHART1920 RCS K2
2-5-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K2
0
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
3'3”6'6”
9'11”13'1”
16'5”19'8”
23'0”(1m)
(2m)
(3m)
(4m)
(5m)
(6m)
(7m)
26'3”(8m) 29'6”
(9m)
3'3”
6'6”
9'11”
13'1”
16'5”
19'8”
23'0”
(1m)
(2m)
(3m)
(4m)
(5m)
(6m)
(7m)
26'3”(8m)
29'6”(9m)
36'1”(11m)
32'10”(10m) KG
LB
89744070
61302780
46312100
152346910
![Page 42: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/42.jpg)
Section - 5 36 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K3
70490223
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490223
CAPACITY CHART1920 RCS K3
2-5-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K3
0
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
3'3”
6'6”
9'11”
13'1”
16'5”
19'8”
23'0”
(1m)
3'3”(1m)
(2m)
6'6”(2m)
(3m)
9'11”(3m)
(4m)
13'1”(4m)
(5m)
16'5”(5m)
(6m)
19'8”(6m)
(7m)
23'0”(7m)
26'3”(8m)
26'3”(8m)
29'6”(9m)
29'6”(9m)
32'10”(10m)
32'10”(10m)
36'1”(11m)
42'8”(13m)
39'4”(12m)
36'1”(11m)
86003900
145736610
58212640
43221960
34401560
KGLB
![Page 43: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/43.jpg)
Section - 5 37 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K4
70490224
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490224
CAPACITY CHART1920 K4
2-5-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
6'6”
13'1”
19'8”
(2m)
(4m)
(6m)
26'3”(8m)
32'10”(10m)
52'6”(16m)
45'11”(14m)
39'4”(12m)
03'3”
(1m)
6'6”(2m)
9'11”(3m)
13'1”(4m)
16'5”(5m)
19'8”(6m)
23'0”(7m)
26'3”(8m)
29'6”(9m)
32'10”(10m)
36'1”(11m)
39'4”(12m)
42'8”(13m)
KGLB
139556330
82473740
55132500
40571840
25801170
31531430
![Page 44: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/44.jpg)
Section - 5 38 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K5
70490225
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490225
CAPACITY CHART1920 RCS K5
2-6-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K5
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0
6'6”
13'1”
19'8”
(2m)
6'6”(2m)
(4m)
13'1”(4m)
(6m)
19'8”(6m)
26'3”(8m)
26'3”(8m)
32'10”(10m)
32'10”(10m)
52'6”(16m)
52'6”(16m)
59'0”(18m)
45'11”(14m)
45'11”(14m)
39'4”(12m)
39'4”(12m)
133826070
79383600
52482380
37931720
29111320
23371060
1985900
LBKG
![Page 45: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/45.jpg)
Section - 5 39 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart, K6
70490226
REVISIONSREV ECO DESCRIPTION DATE BY
NOTES:MATL: .005“ VELVET FINISH LEXAN
ADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 10.50”H x 8.00”WCOLORS: BLACK ON WHITE BACKGROUND, AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIV.
70490226
CAPACITY CHART1920 RCS K6
2-6-2019IOWA MOLD TOOLING CO., INC
BOX 189, GARNER, IA 50438TEL: 641-923-3711 FAX: 641-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
BKS
B
FULL
IOWA MOLD TOOLING CO., INC.BOX 189 • GARNER • IA • 50438 • 641-923-3711
Model1920 RCS K6
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
0
0
6'6”
13'1”
19'8”
(2m)
6'6”(2m)
(4m)
13'1”(4m)
(6m)
19'8”(6m)
26'3”(8m)
26'3”(8m)
32'10”(10m)
32'10”(10m)
52'6”(16m)
52'6”(16m)
59'0”(18m)
59'0”(18m)
65’7”(20m)
45'11”(14m)
45'11”(14m)
39'4”(12m)
39'4”(12m)
128755840
76513470
50052270
35721620
26901220
2139970
1786810
1544700
LBKG
![Page 46: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/46.jpg)
Section - 5 40 1920 - RCS K1-K6 Load Capacity Charts
1910 / 1920 RCS - Manual # 99906442
1920 - RCS Lifting Capacity Chart K1 - K6
K6
K5
K4
K3
K2
K1
M 4,3 6,2
2100
2640
2780 1610
1220
M 4,3 6,3 8,3 10,4
3900 1960 M 4,4
1840
M 4,6 6,6 8,6 10,7 12,9 15,0 17,2 19,6 1620 500 007 2270 810 079 3470 1220
M 4,6 6,5 8,5 10,6 12,8 14,9 17,2 1720 740 009 2380 1060 0231
M039 2500 1170 0341 3740
KG
3572 1103 5005 1786 7651 2690 LB
KG 3600
KG
KG
KG 4070
KG 4200 2910
Lifting capacity with manual extension Lifting capacity without manual extension
2139 154415’2” 21’6” 28’1” 34’11” 42’2” 49’2” 56’5” 64’3”FT
6417 9261 LB 14’0” 20’4”FT
4631 6130 8974 3550LB 14’2” 20’6” 27’1” 34’1”FT
43225821 8600 3440LB 269014’5” 20’9” 27’4” 34’3” 41’8”FT
6 ,3 8,3
8,4
156010,4
10,5
12,7
12,7 15,04,5 6,4
4057 5513 2051 8247 3153
258014’8” 21’0” 27’7” 34’5” 41’8” 49’2”
LB FT
3793 5248 1985 7938 2911 LB 2337 163214’11” 21’3” 27’10” 34’8”
‘41’11” 49’0” 56’5”FT
![Page 47: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/47.jpg)
Section - 6 41 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Section - 61920 - RCS Dimension Drawings
![Page 48: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/48.jpg)
Section - 6 42 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch(2
250)
88.6
”
49.2”
98.4”(1250)
(2500)
11.4”(290)
CL CHASSIS
TOP CHASSIS
15”
2.44
”(6
2)
37.4”
32.7”(382)
(950)
(830)
TOP CHASSIS
2.87”(73)
1.12
”(2
8.5)
85.2
”106.
9”
77.1
”
2.99 (TYP.)(76) (TYP.)
99.1
”
(216
3)(271
5)
(195
9)(251
7)
186.1”(4726)
A
A
A-ATOP CHASSIS
![Page 49: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/49.jpg)
Section - 6 43 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Slewing Radius
24.41”
16.34”
20.47”
(R 620)
(R 415)
(R 520)
14.96”(R 380)
60.8
3”
78.3
5”
79.7
2”
82.8
7”
93.9
0”
(154
5)
(199
0)
(202
5)
(210
5) (238
5)
13°
TOP CHASSIS
![Page 50: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/50.jpg)
Section - 6 44 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch for Truck-Mounted Loader
MOUNTING KIT 4 x M30 x 2 BOLTS
1)
1) 1)
(Min. 900 / Max. 1040)
(38)(38)1.5” 1.5”
(717
)(7
17)
(357
)(3
57)
28.3
”28
.3”
14.1
”14
.1”
Notes:
1. Values dictated by strength considerations.
2. Drill hole when assembling.
3. For installation, please see IMT Installation Manual.
4. For mounting kits or spare parts, please see the Spart Parts Catalog.
MOUNTING KIT 8 x M24 x 2 BOLTS
(Max. 32) (Max. 32)
Min
. 200
/ M
ax. 5
60
(40)
(80)
(Max. 160)
(185)7.3”
(Ø26)
1.6”
3.2”
Max 6.3”
1.2”(See Note 2)
Max.1.3” Max. 1.3”
(Min. 580)
(Max. 1060)
Min. 22.8”
Max. 41.7”
5.51”(140)
CL CHASSIS
Min. 35.4” / Max. 40.9”
![Page 51: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/51.jpg)
Section - 6 45 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Lifting Height at Column
H1 H1K1 2.76 m 108.6”K2 2.71 m 106.7”K3 2.62 m 103.1”K4 2.53 m 99.6”K5 2.44 m 96.1”K6 2.35 m 92.5”
TOP CHASSIS
H1
(2.2
m)
R = 1m
86.6
”
![Page 52: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/52.jpg)
Section - 6 46 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch, Fixed Stabilizer Legs
(2065) (2065)
(1625)
(1137)
(5590)
(4610)
(2340)
(2340)
(1625)
(1137)
(6470)
(2340)
TOP CHASSIS
TOP CHASSIS
TOP CHASSISCL CHASSIS
CL CHASSIS
CL CHASSIS
AB
AB
AB
6’-9”
5’-4” 5’-4”
3’ 7” 3’-7”
6’-9”21’-2”
7’-8”
7’-8”18’-4”
15’-1”
7’-8”
(290)
(290)
(290)11.4”
11.4”
11.4”
B
A
A A
B
A
22.8” 22.8”
26.8” 26.8”
27.8”
31.7”
30.4”34.3”
30.4”
34.4”
32.9”
36.8”
![Page 53: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/53.jpg)
Section - 6 47 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
CONTINUED
(360
)(3
57)
(290
)
(195
)
14.2
”14
”
11.4
”
7.7”
![Page 54: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/54.jpg)
Section - 6 48 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension sketch, swing-up stabilizer legs 30°- 60° (manual)
CL CHASSIS
CL CHASSIS
Type R-20° (Obsolete)
Type R-60°
A
Type R-20° (Obsolete)A
971mm
963mm
871mm
863mm
771mm
763mm
TOP CHASSIS
TOP CHASSIS
A
Type R-60° Type R-60°A
TOP CHASSISCHASSISCL
(2321)(1137)
(1625)
(2065)(2322)
(6452)(2065)
(2322)(5572)
(1625)
(4595) (1137)
(113
7)(1
137)
(113
7)(1
137)
(113
7)
(113
7)AA
A AAA (290)
(290)
(290)
6’-9”7’-7”
7’-7”18’-3”
7’-7”3’-8”
3’-8
”3’
-8”
3’-8
”3’
-8”
3’-8
”
3’-8
”
3’-8”
21’-2”6’-9”
5’-4”
15’-0”
5’-4”
30.4” 34.3”
34.0”
38.2”
38.0”30.0”
11.4”
11.4”
11.4”
![Page 55: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/55.jpg)
Section - 6 49 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
CONTINUED
BC C
B30°60°
C
B
(357) (360)(290)
(195)
(95)
14” 14.2”
7.7”11.4”
3.7”
465mm
744mm
515mm 565mm
918mm831mm
18.3” 20.3” 22.2”
36.1”32.8”29.3”
![Page 56: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/56.jpg)
Section - 6 50 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension sketch, swing-up stabilizer legs 180° (manual + hydraulic)
A A
11.42”(290)
CL CHASSIS
63.98” 92.13” 63.98”
219.29”
81.30” 91.34” 81.30”
253.94”
AA 11.42”(290)
CL CHASSIS
TOP CHASSIS
TOP CHASSIS
A 881 981 1081
A 34.69” 38.62” 42.56”
11.42”(290)
CL CHASSIS
44.76” 44.76”91.30”
180.83”(1137) (1137)(2319)
(4593)
(1625) (1625)(2320)
(5570)
(2065) (2065)(2320)
(6450)
A20
.47”
(520
)
A(5
20)
TOP CHASSIS
20.4
7”
20.4
7”(5
20)
(520
)
20.4
7”
16.4
6”(4
18)
16.4
6”(4
18)
![Page 57: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/57.jpg)
Section - 6 51 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
CONTINUED
B
2.56
”(6
5)(5
3)
(63)
2.08
”
2.48
”
5.9”(150)
3.74”(95)
TOP CHASSIS(1
95)
7.67
”
11.4
2”(2
90)
14.0
6”14
.17”
(357
)(3
60)
B 775mm 875mm 975mm
B 30.51” 34.45” 38.39”
![Page 58: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/58.jpg)
Section - 6 52 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch, Internal Hose Routing
A
99.2
9”(2
522)
BD
øD A B A BK1, K2, K3 ø480 210mm 86mm 8.27” 3.39”
K4 ø520 230mm 66mm 9.06” 2.60”K5 ø570 255mm 41mm 10.04” 1.61”K6 ø620 280mm 16mm 11.02” 0.63”
![Page 59: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/59.jpg)
Section - 6 53 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Stowed in Truck Body
91.8
9”
96.4
2”
52.4
8”
15°
82.3
2”(2
334)
(244
9)
(133
3)
(209
1)
TOP CHASSIS
TOP CHASSIS
![Page 60: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/60.jpg)
Section - 6 54 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Dimension Sketch for Connecting Link
The connection link must be able to move freely at an angle of 35º (minimum) in both directions in relation to the longitudinal direction of the jib extension. This is to minimize the risk of damage to the hook suspension when placing crane equipment in the truck body.
Max. 26,5
Min
. 52
Max. R35
Max. 70
35°
![Page 61: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/61.jpg)
Section - 6 55 1920 - RCS Dimension Drawings
1910 / 1920 RCS - Manual # 99906442
Centers of Gravity
H2
V2 H1
f
H4
V2
V3
H3
V1
Z3
G3
G2
G2
CL CHASSIS
G1
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G3K1 165 1935 785 215 1560 330 1315 5 290 650 955 1605K2 165 1995 800 215 2245 325 1560 10 290 650 1100 1750K3 165 2040 820 215 2980 315 1750 25 290 650 1240 1890K4 165 2070 835 215 3755 305 1900 40 290 650 1370 2020K5 165 2095 850 215 4495 300 2020 55 290 650 1480 2130K6 165 2115 860 215 5130 280 2105 60 290 650 1585 2235
V1 V2 V3 H1 H2 H3 H4 Z3 f G1 G2 G3K1 6.50 76.18 30.91 8.46 61.42 12.99 51.77 0.20 11.42 1433 2105 3538K2 6.50 78.54 31.50 8.46 88.39 12.80 61.42 0.39 11.42 1433 2425 3858K3 6.50 80.31 32.28 8.46 117.32 12.40 68.90 0.98 11.42 1433 2734 4167K4 6.50 81.50 32.87 8.46 147.83 12.01 74.80 1.57 11.42 1433 3020 4453K5 6.50 82.48 33.46 8.46 176.97 11.81 79.53 2.17 11.42 1433 3263 4696K6 6.50 83.27 33.86 8.46 201.97 11.02 82.87 2.36 11.42 1433 3494 4927
[mm] [kg]
[in] [lbs]
![Page 62: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/62.jpg)
This page left intentionally blank
56
1910 / 1920 RCS - Manual # 99906442
![Page 63: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/63.jpg)
Section - 7 57 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Section - 71920 - RCS Hydraulic Drawings
![Page 64: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/64.jpg)
Section - 7 58 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Pressure setting diagram, fixed flow pump & RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 385 5584
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 380 365 5511 5294
Jib cylinderUp A 380 365 5511 5294Down B 250 200 3626 2901
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 200 P 2901Left B P 200 P 2901
GrabOpen A P 250 P 3626Close B P 250 P 3626
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 390 5656
Down - -
Jib cylinderUp 405 5874
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 350 [bar] 5076 [PSI]HDL 300 [bar] 4351 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 gpm
![Page 65: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/65.jpg)
Section - 7 59 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Pressure setting diagram, variable flow pump & RC
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction PortPort-relief
valves [bar]
LS-pressure adjustment
[bar]
Port-relief valves [PSI]
LS-pressure adjustment
[PSI]Main-relief valve 385 5584
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 380 365 5511 5294
Jib cylinderUp A 380 365 5511 5294Down B 250 200 3626 2901
Extension cylindersExtend A P 300 P 4351Retract B P 300 P 4351
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Winch 1,5TLift A P 160 P 2321Lower B P 160 P 2321
Winch 2,5TLift A P 185 P 2683Lower B P 185 P 2683
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding ValvesFunction Direction Opening pressure [bar] Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 390 5656
Down - -
Jib cylinderUp 405 5874
Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 350 [bar] 5076 [PSI]HDL 300 [bar] 4351 [PSI]
Max. pump performanceChoice of pump 1 x Variable 1 x VariablePump performance 100 L/min 26.4 gpm
![Page 66: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/66.jpg)
Section - 7 60 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram PVG32 - Crane functions, control valve fixed and variable flow pump
Fixed pump Variable pump
PVSKM
PVP
PVSKM
PVP
![Page 67: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/67.jpg)
Section - 7 61 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram – Danfoss PVG32, single-circuit fixed 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
PVS
LX
A-PORTB1
A1
A-PORTB2
A2
A-PORTB3
A3
A-PORTB4
A4
A-PORTB5
A5
A-PORTB6
A6
LS
M
P
T PVP
PPVSKM
B
ARemote
controlled stabilizers
B7 / B5
A7 / A5
B1
M3
B A
M2 M1 A1
M M2 M1C2
V2 V1
C1
M
Optional
*) Optional
A-PORT
*)
*)
*)
*)Pst
A-PORTB5
A5
A-PORTB6
A6
A-PORT
A-PORT
*)
*)
*)
*)
B6
B5
A5A6
P2
C3
P1
C1
C2 C4
P2
C3
P1
C1
C2 C4
M M2 M1C2
V2 V1
C1
A5 B5 A6 B6
C2 C1
V2 V1
M
V1V2
C1C2
*) *)
*) *)
HPCO /
2) This A-port is connected to a sequence valve and subsequently the rod side of stabilizer cylinders
PVB32Note 2
V1 V2
D
C3
*)
1) The HPCO port is used for manual controlled stabilizers
Note 1
Notes:
A B
A1 B1PR P T
Pst
T stab. valve
This hose routing if the crane has RC controlled stabilizers
This hose routing if the crane has manual controlled stabilizers
![Page 68: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/68.jpg)
Section - 7 62 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram – Danfoss PVG32, single-circuit variable 7 fcts. RC (3 EXV: FJ + 2 EXV, winch)
PVS
LX
A-PORTB1
A1
A-PORTB2
A2
A-PORTB3
A3
A-PORTB4
A4
A-PORTB5
A5
A-PORTB6
A6
LS
M
P
T PVP
PPVSKM
B
ARemote
controlled stabilizers
B7 / B5
A7 / A5
B1
M3
B A
M2 M1 A1
M M2 M1C2
V2 V1
C1
M
Optional
*) Optional
A-PORT
*)
*)
*)
*)Pst
A-PORTB5
A5
A-PORTB6
A6
A-PORT
A-PORT
*)
*)
*)
*)
B6
B5
A5A6
P2
C3
P1
C1
C2 C4
P2
C3
P1
C1
C2 C4
M M2 M1C2
V2 V1
C1
A5 B5 A6 B6
C2 C1
V2 V1
M
V1V2
C1C2
*) *)
*) *)
HPCO /
2) This A-port is connected to a sequence valve and subsequently the rod side of stabilizer cylinders
PVB32Note 2
V1 V2
D
C3
*)
1) The HPCO port is used for manual controlled stabilizers
Note 1
Notes:
A B
A1 B1PR P T
Pst
T stab. valve
This hose routing if the crane has RC controlled stabilizers
This hose routing if the crane has manual controlled stabilizers
![Page 69: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/69.jpg)
Section - 7 63 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – Overview2 functions:
4 or 2 + 2 extra functions:
4 + 4 extra functions:
4 remote controlled functions:
P
P2
T
B
A
T2
T
1 0 2
P T
B A
(1) (0) (2)
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
55737
P
P2
T
B
A
T2
T
1 0 2
P T
B A
(1) (0) (2)
1 0 2
P T
B A
(0) (2)(1)
B
A
55738
P
P2
T
B
A
T2
T
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
1 0 2
P T
B A
(0) (2)(1)
B
A
1 0 2
P T
B A
(0) (2)(1)
55739
Extra remote controlled functions:
5054
8
V V1
C1 C2 C3 C4C
V
1 pcs. 597711 pcs. 590571 pcs. 61778
![Page 70: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/70.jpg)
Section - 7 64 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 2 fcts.
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A12
A11B12
B11
A12
B12
A11
B11
T
Pst
T
![Page 71: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/71.jpg)
Section - 7 65 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 2 fcts. + 2 available fcts.
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A14
A13
A12
A11
B14
B13
B12
B11
A14
B14
A13
B13
A12
B12
A11
B11
T
P st
T
![Page 72: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/72.jpg)
Section - 7 66 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 4 fcts.
D
CD
C
Crane functions
PVP
PVS
PVSKMP
T
/ HPCOPst
A14
A13
A12
A11
B14
B13
B12
B11
A14
B14
A13
B13
A12
B12
A11
B11
T
Pst
P
![Page 73: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/73.jpg)
Section - 7 67 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts.
C1 C2 C3
D1 D2 D3
D
CD
C
A11 B11
A12 B12
A13 B13
A14 B14
A15 B15
Crane functions
PVP
PVS
PVSKMP
P
/ HPCOPst
A11
B11
A12
B12
A13
B13
A14
B14
A15
B15
T
Pst
T
![Page 74: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/74.jpg)
Section - 7 68 1920 - RCS Hydraulic Drawings
1910 / 1920 RCS - Manual # 99906442
1920 RCS - Pressure Setting for Diagram, Fly-Jib 700
Function Direction Port 1920-K3 FJ700 (Bar)
1920-K3 FJ700 (psi)
Jib
Cyl
inde
r LS-pressure adjustment Up A 320 4641Down B 250 3626
Port-relief valves Up A 350 5076Down B 300 4351
Working Pressure on Load-holding Valves Up 365 5294Down 250 3626
Exte
nsio
n C
ylin
der LS-pressure adjustment Extend A 275 3989
Retract B 275 3989
Working Pressure on Load-holding ValvesExtend 210 3046Retract 430 6237
Load Moment Limitation (LMB) 310 4496
![Page 75: 1910 / 1920 RCS Technical Specifications · 2020. 9. 30. · 1560-10.4 1430-10.5 1320-10.6 1230-10.7 1170-12.7 1060-12.8 970-12.9 900-14.9 810-16 700-17.2 Lifting capacity, manual](https://reader036.vdocuments.site/reader036/viewer/2022071411/610682b56d6579171f312773/html5/thumbnails/75.jpg)
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2021 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com