1430 mcs technical specifications · 2020. 10. 27. · section - 1 5 1430 mcs, technical...
TRANSCRIPT
IOWA MOLD TOOLING CO., INC.
P.O. Box 189Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com
1430 MCS Technical
Specifications
Manual # 99906329
Revised 02-16-2021
Copyright © 2021 Iowa Mold Tooling Co., Inc.All rights reserved
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.
Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company
ii
1430 MCS - Manual # 99906329
iii
1430 MCS - Manual # 99906329
Table of Contents
Section - 1 - Specifications 1
1430 MCS - Specifications ............................................................................................................................21430 MCS - Specifications, Metric .................................................................................................................5
Section - 2 - Lifting Capacities 9
1430 MCS-K1, Lifting Capacity Chart ..........................................................................................................101430 MCS-K2, Lifting Capacity Chart .......................................................................................................... 111430 MCS-K3, Lifting Capacity Chart ..........................................................................................................121430 MCS-K4, Lifting Capacity Chart ..........................................................................................................131430 MCS-K5, Lifting Capacity Chart ..........................................................................................................141430 MCS-K6, Lifting Capacity Chart ..........................................................................................................151430 MCS - K1-K6, Lifting Capacity ...........................................................................................................16
Section - 3 - Dimension Sketches 17
Lifting capacity with winch ............................................................................................................................181430 MCS - Dimension Sketch ...................................................................................................................191430 MCS - Slewing Radius ........................................................................................................................201430 MCS - Dimension Sketch, Truck-Mounted Loader ..............................................................................211430 MCS - Lifting Height at Column ..........................................................................................................221430 MCS - Dimension Sketch, Fixed Stabilizer Legs ................................................................................231430 MCS - Dimension Sketch, Fixed Stabilizer Legs ................................................................................241430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual) ..............................................251430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual) ..............................................261430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic) ...................271430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic) ...................281430 MCS - Dimension Sketch Top Seat, RC & HC Linear .........................................................................291430 MCS - Dimension Sketch, Top Seat (Danfoss X) ................................................................................301430 MCS - Dimension Sketch, Top Seat (HC X) ........................................................................................311430 MCS - Dimension Sketch, Ladder for TS ............................................................................................321430 MCS - Stowed in Truck Body ..............................................................................................................331430 MCS - Dimension Sketch for Connecting Link ....................................................................................341430 MCS - Technical Data, Winch .............................................................................................................351430 MCS - Dimension Sketch, Winch ........................................................................................................361430 MCS - Dimension sketch, Stand-Up Platform (STD & Valve Control) ................................................371430 MCS - Dimension Sketch, Internal Hose Routing ...............................................................................38
Section - 4 - Hydraulic Drawings 39
1430 MCS - Pressure Setting Diagram, Manual ..........................................................................................401430 MCS - Pressure Setting Diagram, Fixed Flow Pump & Danfoss (Man) ..............................................411430 MCS - Danfoss, Single-Circuit Fixed 6 FCTS. RC (2 EXV: Grab + Rotator) .....................................421430 MCS - Danfoss, single-circuit variable6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) .........431430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator) ........................................................................................................................................................441430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab + Rotator) ......................451430 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts. ........................................................................461430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. ........................................................................471430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. RC ..................................................................481430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. ...........................................491430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC .....................................501430 MCS - Lubrication instructions ............................................................................................................511430 MCS - Lubrication instructions ............................................................................................................52
This page left intentionally blank
iv
1430 MCS - Manual # 99906329
1430 MCS - Change of slewing area ...........................................................................................................551430 MCS - Replacement of hydraulic hoses in column .............................................................................601430 MCS - By-pass hose routing for emergency repair .............................................................................64
Section - 1 1 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
Section - 11430 MCS, Technical Specifications
Section - 1 2 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 MCS - Specifications
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment ft-lb 97446 93837 90949 88062 85175 83009Hydraulic reach ft 20’8” 27’7” 34’5” 42’0” 49’3” 56’9”Hydraulic telescopic movement ft 6’3” 12’9” 19’8” 27’0” 34’1” 41’3”
Lifting capacity, hydraulic
lb-ft 6945-14’1” 6658-14’1” 6327-14’5” 6019-14’9” 5732-15’2” 5490-15’2”
lb-ft 4784-20’4” 4519-20’8” 4211-20’8” 3924-21’0” 3682-21’4” 3461-21’8”
lb-ft 3395-27’2” 3086-27’2” 2822-27’7” 2579-27’11” 2381-28’3”
lb-ft 2447-34’1” 2161-34’5” 1940-34’9” 1720-35’1”
lb-ft 1764-41’8” 1521-42’0” 1323-42’4”
lb-ft 1279-48’11” 1080-49’3”
lb-ft 926-56’5”
Lifting Capacities, Manual Extensions
lb-ft2535-34’1” 1852-41’8” 1345-49’3” 1014-56’5” 750-64’4”
lb-ft1962-41’4” 1433-49’3” 1080-57’1”‘ 816-64’4”
lb-ft1521-49’3” 1190-56’9” 882-64’8”
Slewing torque, gross lb-ft 3956Slewing angle ° 400Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis ft-in 7’ 4”Width ft-in 8’ 2”Width with extra valves (int. hose routing) ft-in 8’ 3”Length, no extra valves ft-in 2’ 7’Length, with extra valves (hose guides) ft-in 3’ 1”Length, with extra valves (int. hose routing) ft-in 2’ 7”Stabilizer spread, S1 (standard) ft-in 15’ 1”Stabilizer spread, S2 ft-in 18’ 3”Stabilizer spread, D ft-in 21’ 2”
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 3 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 MCS - Specifications - continued
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers lb 2888 3197 3505 3803 4068 4277Stabilizers, S1 fixed lb 441Stabilizers, S1 swing-up lb 452Stabilizers, S1 hydr. swing-up lb 474Stabilizers, S2 fixed lb 518Stabilizers, S2 swing-up lb 529Stabilizers, S2 hydr. swing-up lb 551Stabilizers, D fixed lb 661Stabilizers, D swing-up lb 561Stabilizers, D hydr. swing-up lb 694Mounting kit, 4 bolts lb 121Mounting kit, 8 bolts lb 132Tank, excl. oil (fitted on loader) lb 99
Manual extensions lb —187165143
16514399
1439988
9988
88
Oil in loader lb 55 66 77 88 99 99
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. lb 132Stand-up controls (HS), direct valve control lb 154Top seat (TS) lb 198Top seat, ladder lb 441 extra valve, hose guides lb 88 121 143 165 187 2091 extra valve, int. hose routing lb 165 165 165 176 176 1872 extra valves, hose guides lb 132 165 198 231 265 2982 extra valves, int. hose routing lb 287 287 287 309 320 331Winch (1.5 t), single snatch block lb 386 397
Winch (1.5 t), double snatch block lb 375 386
Winch (2.5 t), single snatch block lb 441 452
Winch (2.5 t), double snatch block lb 430 441
High-pressure filiter lb 15
Oil cooler lb 55
Max. load on stabilizer (per stab. cylinder) Unit K1 K2 K3 K4 K5 K6S1, fixed ft-lb
62693
S1, swing-up ft-lbS1, hyd swing-up ft-lbS2, fixed ft-lbS2, Swing-up ft-lbS2, hyd swing-up ft-lbD, fixed ft-lb
50154D, swing-up ft-lbD, hyd swing-up ft-lb
Section - 1 4 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 MCS Technical Specifications - Continued
Power consumption / oil capacity Unit K1 K2 K3 K4 K5 K6Working pressure psi 4786Tank capacity (fitted on loader) gal 24Max. pump performance, Hydrocontrol 1-circuit g/min 11.9
Max. pump performance, Danfoss fixed flow g/min 18.5Max. pump performance, Danfoss variable g/min 26.4
Section - 1 5 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 - Specifications, Metric
Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3
Load moment tm 13.5 13 12.6 12.2 11.8 11.5Hydraulic reach m 6.3 8.4 10.5 12.8 15.0 17.3Hydraulic telescopic movement mm 1930 3940 6040 8230 10390 12580
Lifting capacity, hydraulic
kg-m 3150-4.3 3030-4.3 2870-4.4 2730-4.5 2600-4.6 2490-4.6
kg-m 2170-6.2 2040-6.3 1910-6.3 1780-6.4 1670-6.5 1570-6.6
kg-m 1540-8.3 1400-8.3 1280-8.4 1170-8.5 1080-8.6
kg-m 1110-10.4 980-10.5 880-10.6 780-10.7
kg-m 800-12.7 690-12.8 600-12.9
kg-m 580-14.9 490-15.0
kg-m 420-17.2
Lifting Capacities, Manual Extensions
kg-m1150-10.4 840-12.7 610-15.1 460-17.2 340-19.6
kg-m890-12.6 650-15.0 490-17.4 370-19.6
kg-m690-15.0 540-17.3 400-19.7
Slewing torque, gross kNm 17.6Slewing angle ° 400Max. heel at max. load moment ° 5
Slewing speed °/s 24
Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis mm 2250Width mm 2500Width with extra valves (int. hose routing) mm 2535Length, no extra valves mm 825Length, with extra valves (hose guides) mm 950Length, with extra valves (int. hose routing) mm 825Stabilizer spread, S1 (standard) mm 4615Stabilizer spread, S2 mm 5900Stabilizer spread, D mm 6470
1) Weights ± 5% because of tolerances for plate thickness
Section - 1 6 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 MCS Specifications - Metric, continued
Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers kg 1310 1450 1590 1725 1845 1940Stabilizers, S1 fixed kg 200Stabilizers, S1 swing-up kg 205Stabilizers, S1 hydr. swing-up kg 215Stabilizers, S2 fixed kg 235Stabilizers, S2 swing-up kg 240Stabilizers, S2 hydr. swing-up kg 250Stabilizers, D fixed kg 300Stabilizers, D swing-up kg 300Stabilizers, D hydr. swing-up kg 315Mounting kit, 4 bolts kg 55Mounting kit, 8 bolts kg 60Tank, excl. oil (fitted on loader) kg 45
Manual extensions kg —857565
756545
654540
4540
40
Oil in loader kg 25 30 35 40 45 45
Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. kg 60Stand-up controls (HS), direct valve control kg 70Top seat (TS) kg 90Top seat, ladder kg 201 extra valve, hose guides kg 40 55 65 75 85 951 extra valve, int. hose routing kg 75 75 75 80 80 852 extra valves, hose guides kg 60 75 90 105 120 1352 extra valves, int. hose routing kg 130 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 180
Winch (1.5 t), double snatch block kg 170 175
Winch (2.5 t), single snatch block kg 200 205
Winch (2.5 t), double snatch block kg 195 200
High-pressure filiter kg 7
Oil cooler kg 25
Max. load on stabilizer (per stab. cylinder) Unit K1 K2 K3 K4 K5 K6S1, fixed kN
85
S1, swing-up kNS1, hyd swing-up kNS2, fixed kNS2, Swing-up kNS2, hyd swing-up kND, fixed kN
68D, swing-up kND, hyd swing-up kN
Section - 1 7 1430 MCS, Technical Specifications
1430 MCS - Manual # 99906329
1430 Specifications - Metric, continued
Power consumption / oil capacity Unit K1 K2 K3 K4 K5 K6Working pressure Bar 330Tank capacity (fitted on loader) L 90Max. pump performance, Hydrocontrol 1-circuit L/min 45
Max. pump performance, Danfoss fixed flow L/min 70Max. pump performance, Danfoss variable L/min 100
Minimum Chassis SpecsFront Axle Rating (GAWR) 12,000 (5443 kg)Rear Axle Rating (GAWR) 21,000 (9525 kg)Resistance to Bending Moment 1,400,000 (16134 kg-m)
This page left intentionally blank
8
1430 MCS - Manual # 99906329
Section - 2 9 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
Section - 21430 MCS Load Capacity Charts
Section - 2 10 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K1, Lifting Capacity Chart
MODEL 1430 MCS K1
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MCS K1
BKS
70490149
70490149(2m) (4m) (6m)6’ 6” 13’ 1” 19’ 7”
0
(2m)
(4m)
(6m)
(8m)
6’ 6”
13’ 1”
19’ 7”
26’ 3”
0
(1m) (3m) (5m) (7m)3’ 3”
(1m)3’ 3”
9’ 11”
(3m)9’11”
16’ 5”
(5m)16’ 5”
23’ 0”
(7m)23’ 0”
(9m)29’ 5”
69453150 2170
lb
kg
110235000
4784
Section - 2 11 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K2, Lifting Capacity Chart
MODEL1430 MCS K2
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MC K2
BKS
70490150
70490150(2m) (4m) (6m) (8m)6’ 6” 13’ 1” 19’ 8” 26’ 3”
0
(2m)
(4m)
(6m)
(8m)
(10m)
(12m)
6’ 6”
13’ 1”
19’ 8”
26’ 3”
32’ 10”
39’ 4”
0
(1m) (3m) (5m) (7m) (9m)3’ 3”
(1m)3’ 3”
9’ 11”
(3m)9’ 11”
16’ 5”
(5m)16’ 5”
23’ 0”
(7m)23’ 0”
29’ 6”
(9m)29’ 6”
(11m)36’ 1”
66583020
45192050
33951540
lb
kg
105824800
Section - 2 12 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K3, Lifting Capacity Chart
MODEL 1430 MCS K3
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MCS K3
BKS
70490151
70490151(2m) (4m) (6m) (8m) (10m)
(11m)
(13m)
6’ 6” 13’ 1” 19’ 8” 26’ 3” 32’10”
42’ 8”
0
(2m)
(4m)
(6m)
(8m)
(10m)
(12m)
6’ 6”
13’1”
19’ 7”
26’3”
32’10”
39’ 4”
0
(1m) (3m) (5m) (7m) (9m)3’ 3”
(1m)3’ 3”
9’ 11”
(3m)9’ 11”
16’ 5”
(5m)16’ 5”
23’0”
(7m)23’0”
29’ 6”
(9m)29’ 6”
36’ 1”
(11m)36’ 1”
63272870
42111910
30861400 1110
lb
kg
2447
105824800
Section - 2 13 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K4, Lifting Capacity Chart
39241780
28221280
2161980
1764800
60192730
99214500
MODEL 1430 MCS K4
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
(2m) (4m) (6m) (8m) (10m)(11m)6’ 6” 13’ 2” 19’ 8” 26’ 3” 32’ 10”
0(1m) (3m) (5m) (7m) (9m)
3’ 3” 9’ 11” 16’ 5” 23’ 0” 29’ 6” 36’ 1”(13m)42’ 8”
(12m)39’ 4”
(14m)44’ 11”
(16m)52’ 6”
(2m)
(4m)
(6m)
(8m)
(10m)
(12m)
6’ 6”
13’ 1”
19’ 8”
26’ 3”
32’ 10”
39’ 4”
0
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MCS K4
BKS
70490152
70490152
lb
kg
Section - 2 14 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K5, Lifting Capacity Chart
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MCS K5
BKS
70490153
70490153(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m)6’ 6” 13’ 1” 19’ 8” 26’ 3” 32’ 10” 39’ 4” 45’ 11” 52’ 6”0
(2m)
(4m)
(6m)
(8m)
(10m)
(12m)
(14m)
(16m)
(18m)
6’ 6”
13’ 1”
19’ 8”
26’ 3”
32’ 10”
39’ 4”
45’ 11”
52’ 6”
59’ 0”
0
1279580
57322600
36821670
25791170
1940880
1521690
lb kg
MODEL1430 MCS K5
97004400
Section - 2 15 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS-K6, Lifting Capacity Chart
Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN
VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV CN DESCRIPTION DATE BY
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438
TEL: 515-923-3711 FAX: 515-923-2424
TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATE
DATE SCALETITLE
SIZE DWG NO
SHT OF
A
FULL5/07/2018 DECAL- CP1430 MCS K6
BKS
70490154
lb kg
70490154
54902490
34611570
23811080
1720780
1323600
1080490
926420
(2m)
(2m)
(4m)
(6m)
(8m)
(10m)
(12m)
(14m)
(16m)
(18m)
(20m)
(4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m)
6’ 6”
6’ 6”
13’ 1”
13’ 1”
19’ 8”
19’ 8”
26’ 3”
26’ 3”
32’ 10”
32’ 10”
39’ 4”
39’ 4”
45’ 11”
45’11”
52’ 6”
52’6”
59’ 0”
59’ 0”
65’ 7”
0
0
MODEL1430 MCS K6
94804300
Section - 2 16 1430 MCS Load Capacity Charts
1430 MCS - Manual # 99906329
1430 MCS - K1-K6, Lifting Capacity
K5
K4
K3
2579
K2
K1
FT 14’1” 20’4”47846945
1521
LB
M21703150KG
10145732 1940LBFT
6658 15211962 LBFT
25353395
1279
4519
M 4,3 6,3 8,3 10,4 12,6 15,03020 690098 KG 115015402050
11906327 1433 1852LBFT
244730864211
M 4,4 6,3 8,3 10,4 12,7 15,0 17,3 5402870 650 840KG 111014001910
882
400
3924 1080 13456019 1764 2161LBFT
2822
M 4,5 6,4 8,4 10,5 12,7 15,0 17,4 19,7 1780 490 6102730 800 980KG 1280
8163682
1170 690 4602600 880KG 580 M 4,6 6,5 8,5 10,6 12,8 14,9 17,2 19,6
3701670
LBFT
5490 3641 2381 1720 1323 1080 926 750
M 4,6 6,6 8,6 10,7 12,9 15,0 17,2 19,6KG 2490 1570 1080 780 600 490 420 340
K6
LIFTING CAPACITY WITH MANUAL EXTENSIONS
LIFTING CAPACITY WITHOUT MANUAL EXTENSIONS
4,3
14’1”
14’5”
14’9”
15’2”
15’2” 21’8” 28’3” 35’1” 42’4” 49’3” 56’5” 64’4”
21’4” 27’11” 34’9” 42’0” 48’11” 56’5” 64’4”
21’0” 27’7” 34’5” 41’8” 49’3” 57’1” 64’8”
20’8” 27’2” 34’1” 41’8” 49’3” 56’9”
20’8” 27’2” 34’1” 41’4” 49’3”
6,2
Section - 3 17 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
Section - 31430 MCS, Dimension Drawings
Section - 3 18 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
Lifting capacity with winch
Hydraulic hoist type
0°
65°
90°
Not recommended workning angle.
Dinamic S 25 Brevini 2500
Dinamic P9E
Dinamic P15E
Hydraulic hoist type
Dinamic S 25 Brevini 2500
Dinamic P9E
Dinamic P15E
MAXW MAXWMAXWD MAXWD
1500 kg 3000 kg
2500 kg 5000 kg
6400 kg3200 kg
3307 lb
5512 lb
7055 lb
6614 lb
11023 lb
14110 lb
Section - 3 19 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch
73 2.9”
28,5
1953
6
’5”
2162
7’2
‘
2715
8’
11”
225
0
7’5”
1250 4’1”
2500 8’2”
290 CL CHASSIS
76 (TYP.)
4726 15’6”
381
2502
8
’2”
950
825
A
TOP CHASSISA-A
TOP CHASSIS TOP CHASSIS
A 3”
Metric=Millimeters
11.5”
37.4”
34.5”
15”
Section - 3 20 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Slewing Radius
R380
R470 18.5”
R440 17.3”
R600 23.7”
1745
5’
9”
2075
6’
10”
2095
6’
11‘
2375
7’
10”
10°
TOP CHASSIS
15”
Section - 3 21 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Truck-Mounted Loader
Max.32 Max.32
Max.6.3”Max.160
26
80
7”185
1.5”
40
28”
717
14”
357
Min.580Min 23”
Max.1060Max.3’6”
Min.2’11”/Max.3’5”
Min.900/Max.1040
38 38
Min
.200
/Max
.560
Min
.7.8
” Max
.22”
140
1)
1)1)
See note 2)
Mounting kit 8 x M24x2 bolts
Mounting kit 4 x M30x2 bolts
Notes:
1) Values dictated by strength considerations.
2) Drill hole when assembling
3) As regards installation - please see HMF Installation Manual
4) Mounting kits or spare parts - please see the Spare Parts Catalogue of the individual loader
CL CHASSIS
1.2” 1.2”
28”
717
14”
357
1.5” 1.5”
Section - 3 22 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
70399472
Model 40/275 K5FJ1000 K3
25555630 19504300 13602995 10202245
6'(1.83 m)0CENTERLINE 18'(5.49 m)12'(3.66 m) 30'(9.14 m)24'(7.32 m) 42'(12.80 m)36'(10.97 m) 54'(16.46 m)48'(14.63 m) 66'(20.12 m)60'(18.29 m) 72'(21.95 m)
0MOUNTING SURFACE
6'(1.83 m)
12'(3.66 m)
18'(5.49 m)
24'(7.32 m)
30'(9.14 m)
36'(10.97 m)
42'(12.80 m)
48'(14.63 m)
54'(16.46 m)
60'(18.29 m)
72'(21.95 m)
66'(20.12 m)
84'(25.60 m)
78'(21.95 m)
80°
65°
45°
45°
20º30°
KGLB
11652565 10502315 9552105 8701915
14303150 12752810 11552545 10502315
18604100 16403615 14653230 11402510
29506500 22705005 15953515 12002645
29506500 23155100 16253580 12272705
15953515
29506500 2950650021054640
29506500
23155100
16253580
12202690
NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT
REVISIONSREV ECO DESCRIPTION DATE BY
70399472
IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438TEL: 515-923-3711 FAX: 515-923-2424TECH PUBS GENERATED DRAWING
DRAWN BY
APPROVED BY DATEDATE SCALETITLE SIZE DWG NO SHT OFKJB AFULL12-19-13 DECAL- MODEL 40/275K5 / FJ1000 K3
A 9000 KJB12/19/2013Changed model description
1430 MCS - Lifting Height at Column
H1K1 9’0”
K2 8’10”
K3 8’7”
K4 8’4”
K5 8’0”
K6 7’8”
7’3”
2,2m H
1
R=1m
TOP CHASSIS
H1K1 2,76m
K2 2,71m
K3 2,62m
K4 2,53m
K5 2,44m
K6 2,35m
Section - 3 23 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Fixed Stabilizer Legs
A 2’6” 2’11” 3’2”
20”
520
A A20
”20
”
20”
520
290 CL CHASSIS
5’4”1625
23407’8” 5’4”1625559018’4”
290 CL CHASSIS
3’8”1137
3’8”1137
23407’8”
461415’1”
A20
”52
0
A20
”52
0
6’9”2065
23407’8” 6’9”2065647021’2”
520
520
AA 290 CL CHASSIS
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
A 777 877 977
11”
11”
11”
Section - 3 24 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Fixed Stabilizer Legs
27”
677
440
17”
4610 / 5590 / 6470
15’1” / 18’4” / 21’3”
195
290
360
357
TOP CHASSIS
Stabilizer cylinder, C80-440
Section - 3 25 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual)
290 11”
CL CHASSIS
5’4”1625
23227’7” 5’4”1625557218’3”
A20
”52
0
A20
”52
0
290 11”
CL CHASSIS
A20
”52
0
A20
”52
0
7’7”3’8”1137
3’8”113715’1”
23214595
6’9”2065
20”
520
23227’7” 6’9”2065
20”
520
645221’2”
AA
290 11”
CL CHASSIS
Type R-20° (Obsolete)
Type R-60°
A
3’2”
3’1”
2’10”
2’9”
2’6”
2’6”
TOP CHASSIS
TOP CHASSIS
TOP CHASSIS
AType R-20° (Obsolete)
Type R-60°
A
971
963
871
863
771
763
A
Section - 3 26 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual)
Type R-60°
BC C
B30°60°
20°
D
4”
4”
95
95
195290
360357Type R-60°
Type R-20° (Obsolete)
C
B
36”22”
33”20”
29”18”
16”15”13”D
C
B
918565
831515
744465
412378344D
14” 14.1”11”
7.7”
Section - 3 27 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic)
290 11”
CL CHASSIS
A16
”41
8
A16
”41
8
6’9”1625
2320 6’9”16255570
7’7”
21’9”
18’3”
290 11”
CL CHASSISA20
”52
0
A20
”52
0
23197’7”3’8”1137
3’8”1137459315’1”
6’9”2065 6450
2320 6’9”2065
418
16”
16”
A A41
8
29011”
CL CHASSIS
TOP CHASSIS
TOP CHASSIS
A 35” 37” 43” A 881 981 1081
Section - 3 28 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic)
B
6553 63
150
95
195
290
357
360
TOP CHASSIS
B 31” 34” 38” B 775 875 975
357 14” 360 14.1”290 11”195 7.7”
95 3.7”65 2.5”53 2.1”63 2.5”
mm IN
mm IN
Section - 3 29 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch Top Seat, RC & HC Linear
2’7”785
8702’10”
1’7”475
5’0” 1530
1’7”
490
7’8”
2330
R10
20
R10
80
3’11
”12
00
Section - 3 30 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Top Seat (Danfoss X)
800
2’7”890
2’11”
6152’0”
4’8”
1410
1’8”
500
2220
7’3”
200.7”
4’10
”14
80
R11
90
R11
40
Section - 3 31 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Top Seat (HC X)
2’5”735
2’8”825
1’11”585
4’8”
1410
1’4”
400
R11
35
R119
5
Section - 3 32 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Ladder for TS
4’0”
1230
1’9”
520
TOP CHASSIS
Notes:
1) Ladder cannot be used for TS RC
2) There is no access to the top seat when the loader is in stowing position
Section - 3 33 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Stowed in Truck Body
2322
2432
1333
15°
2091
TOP CHASSIS
TOP CHASSIS
7’ 6
”
8’ 0
”
6’ 9
”4’ 4
”
Section - 3 34 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch for Connecting Link
The following design is recommended so the connecting link can swing sufficiently when using the equipment or when stowing and/or folding in the truck body.
The connecting link must be able to move freely at an angle of 35° (minimum) in both directions of the jib extension. This is to minimize the risk of damage to the hook suspension when placing crane equip-ment in the truck body.
Max. 26,5
Min
. 52
Max. R35
Max. 70
35°
Recommended dimensions for connecting link.
Section - 3 35 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Technical Data, Winch
PERFORMANCE (AT 2176 PSI) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer lbs 3307 5512Max. wire pull – 2nd layer lbs 3020 5071Max. wire pull – 3rd layer lbs 2778 4630Max. wire pull – 4th layer lbs 2579 4299PERFORMANCE (150 BAR) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer kg 1500 2500Max. wire pull – 2nd layer kg 1370 2300Max. wire pull – 3rd layer kg 1260 2100Max. wire pull – 4th layer kg 1170 1950
WIRE SPEED (AT 40 G/MIN) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer g/min 5.8 6.3Max. wire pull – 2nd layer g/min 6.3 6.9Max. wire pull – 3rd layer g/min 6.9 7.4Max. wire pull – 4th layer g/min 7.4 7.9WIRE SPEED (AT 40 L/MIN) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer m/min 22 24Max. wire pull – 2nd layer m/min 24 26Max. wire pull – 3rd layer m/min 26 28Max. wire pull – 4th layer m/min 28 30
WEIGHTS UNIT 1.5T WINCH 2.5T WINCHTare weight, winch (CE) lbs 143 198Fixed parts (valve section, brackets,hoses etc.) lbs 110 110Wire Ø10 x 50 m lbs 66 66Spare parts, single snatch block lbs 66 66Spare parts, double snatch block lbs 88 88WEIGHTS UNIT 1.5T WINCH 2.5T WINCHTare weight, winch (CE) kg 65 90Fixed parts (valve section, brackets, hoses etc.) kg 50 50Wire Ø10 x 50 m kg 30 30Spare parts, single snatch block kg 30 30Spare parts, double snatch block kg 40 40
Section - 3 36 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Winch
2,5T: 3’0”1,5T: 3’1”
2,5T: 9251,5T: 945
1010
Section - 3 37 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension sketch, Stand-Up Platform (STD & Valve Control)
1’10
”55
5
5’11
”
1820
2’9”850
TOP CHASSIS
Stand-Uo Platform (STD)
1515
5’0”
11”
275
2’10”875
TOP CHASSIS
Stand-Up Platform (Valve Control)
Section - 3 38 1430 MCS, Dimension Drawings
1430 MCS - Manual # 99906329
1430 MCS - Dimension Sketch, Internal Hose Routing
B
8’3”
250
2 A
D
øD A B
K1, K2, K3
K4
K5
K6
øD A B
K1, K2, K3 480 230mm 78mm
K4 520 250mm 58mm
K5 570 275mm 33mm
K6 620 300mm 8mm
Feet / Inches Metric
480
520
570
620
9.1” 3.1”
9.8” 2.3”10.8” 1.3”
11.8” 0.3”
Section - 4 39 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Section - 41430 MCS, Hydraulic Drawings
Section - 4 40 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Pressure Setting Diagram, Manual
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction Port HDL(BAR)
HDL [PSI]
Main-relief valve 330 4786
Slewing systemRight A P PLeft B P P
Boom cylinderDown A 100 1450Up B 340 4931
Jib cylinderUp A 340 4931Down B 200 2901
Extension cylindersExtend A P PRetract B P P
RotatorRight A 200 2901Left B 200 2901
GrabOpen A 200 2901Close B 200 2901
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding Valves
Function Direction Port Opening Pressure [BAR]
Opening pressure [PSI]
Boom cylinder 350 5076Jib cylinder 350 5076Slewing system 185 2683
Extension cylindersRetract A 210 3046Extend B 430 6237
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 320 [BAR] 4641 [PSI]HDL 290 [BAR] 4206 [PSI]
Max. pump performancePump performance, 1 Circuit 45 L/min 11.9 g/pm
Section - 4 41 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Pressure Setting Diagram, Fixed Flow Pump & Danfoss (Man)
Working Pressure on Main-Relief Valve & Port- Relief Valves
Function Direction Port Port Relief(BAR)
LS Pressure [BAR]
Port Relief[PSI]
LS Pressure [PSI]
Main-relief valve 300 4351
Slewing systemRight A P 180 P 2611Left B P 180 P 2611
Boom cylinderDown A 125 100 1813 1450Up B 320 350 4641 5076
Jib cylinderUp A 350 350 5076 5076Down B 250 230 3626 3336
Extension cylindersExtend A P 280 P 4061Retract B P 280 P 4061
RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351
GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351
Separate stabilizer valve All 150 2176
Working Pressure on Load-holding Valves
Function Direction Opening Pressure [BAR]
Opening pressure [PSI]
Slewing systemRight 185 2683Left 185 2683
Boom cylinderUp 325 4714Down - -
Jib cylinderUp 350 5076Down 300 4351
Extension cylindersRetract 430 6237Extend 210 3046
Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 285 [bar] 4134 [PSI]
Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 g/pm
Section - 4 42 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Danfoss, Single-Circuit Fixed 6 FCTS. RC (2 EXV: Grab + Rotator)
Option
Recommended
B1M3B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
PVP
T
P
LS M
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A-PORTA6
B6
A-PORTA5
B5
A-PORTA4
B4
A3
B3A-PORT
A-PORTA2
B2
A-PORTA1
B1
63092/63301/63303/63313
P PVSKPst
Tst
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
4940
1
Obsolete for 1430-K
Section - 4 43 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Danfoss, single-circuit variable6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)
B1M3B
A
M2
M1
A1
55227
C2 C1
V2 V159
044
55261 / 55262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
59823
A-PORTA6
B6
A-PORTA4
B4
A-PORTA3
B3
58479
63393
A-PORTA1
B1
63394
T
58479
PVP
P
59823
LS M
58478
A-PORTA5
B5
A-PORTA2
B2
PVSK
HPCO
P
PVPT
P
LS
PVSI
LX
Pst
Option
Recommended
494015847
8
6340844
Tst
58478
58478
A1
B1
5051
750
517
Option
Section - 4 44 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator)
Option
A-PORT
A-PORT
A-PORT
A-PORT
C2 C1
V2 V1
5904
4
Q-MODULT
P
5526
1 / 5
5262
A1 B1
A B
A-PORT
A-PORT
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
PstHPCO
M
A5
B5
A2
B2
A3
B3
A4
B4
A1
B1
A6
B6
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
NEM
-MO
DU
L
TP
55265 / 55266 / 55267
Tst
B1M3B
A
M2
M1
A1
55227
Max 3 bar
Section - 4 45 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab + Rotator)
Pst HPCO
B1M3B
A
M2
M1
A1
55227
C2 C1
V2 V1
5904
4
5526
1 / 5
5262
A1 B1
A B
5902
7
MM2M1 C1C2
V1V2
X4
X1
X2
X3
A1
B1
58478
58478
58478
58478
58478
58478
58478
58478
58478
58479
Tst
A-PORTA5
B5
M
55290
A-PORTA1
B1
A-PORTA4
B4
A-PORTA2
B2
A3
B3A-PORT
A-PORTA6
B6
Option
Q-MODULP2
M
TQ-MODUL
T
P1
Section - 4 46 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts.
PstTst
A-PORT
A2 B2
A-PORT
A1 B1
5522
5
PT
5849
6
5849
6
Section - 4 47 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts.
PstTst
D
C
5522
8
5849
6
5849
6
D
C55
228
A14 B14 A13 B13 A12 B12 A11 B11
5522
6 / 5
5281
PT
A-PORT A-PORT A-PORTA-PORT
Section - 4 48 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
PstTst
A13 B13 A12 B12
5527
6
T
B-PORT
A-PORT
A11 B11
PA-PORT
B-PORT
NEM-MODULT P
T
ø1 mmø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
49187
49187
Only when HR stabilizer
Section - 4 49 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts.
D
C55
228
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
A15 B15 A14 B14 A13 B13 A12 B12
5527
7
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
PA-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Section - 4 50 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC
D
C
5522
8
5849
6
5849
6
D
C
5522
8
Separate traverse
PstTst
P
P
A15 B15 A14 B14 A13 B13 A12 B12
5527
5
TA-PORT
B-PORT
A-PORTA-PORT
A11 B11
A-PORT
OPT.
B-PORTB-PORTB-PORT
OPT.OPT.OPT.
NEM-MODULT
T
ø1 mm ø1 mm
50521
C1
C2
C3
D1
D2
D3
D4
C4
Only when HR stabilizer
49187
49187
Section - 4 51 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Lubrication instructions
The present instructions are valid for the following loader cranes:
For the K-Series Cranes Catalogue
1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091
For the T-Series
Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101
The crane models concerned by these instructions are to a great extent equipped with maintenance-free composite bearings. However, for a limited number of bearings, regular lubrication has to be carried out according to these instructions.
The crane has to be greased in the following places:
1. Central greasing on the base.2. The push rods at the boom and jib cylinders .3. Sliding surfaces in the boom system.
Please see the Instruction Manual, Cranes, for recommended oil and grease.
Re 1) Central lubrication on the base: The base is equipped with a central greasing point where all lubrication of moving parts in the slewing system is carried out.
The central greasing point is placed on the cross beam of the base and is indicated in the figure below.
Section - 4 52 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Lubrication instructionsLubrication instructions
Figure 1 - Central greasing point on the base
Greasing has to be carried out at the greasing points indicated above, while the crane is swung from stop to stop. Repeat the lubrication of the cogging twice. The crane has to be lubricated again after 50 hours of operation or as a minimum every month. Furthermore the crane has to be lubricated right before a longer period of standstill.
Below is indicated where the central greasing points are connected on the central part of the base.
Figure 2 – Connection points on the central part of the base.
Top bearing
Guide for rack
Top bearing
CoggingBottombearing
Cogging
Top bearing (2 places)
Guide for rack
Bottombearing
Section - 4 53 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Lubrication instructions
Re 2) For the K-Series:
The push rods at the boom and jib cylinders: Lubricate the crane’s push rods at the boom cylinder at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.
Figure 3 - Greasing points on inner push rods at the boom cylinder
Note:The 1310K, 1430K, 1530K, 1510K, 1730K, 1830K, 1810K, 2030K, 2130, 2210K, 2430K, 2630KSeries only have a push rod at the jib cylinder.
Lubricate the crane’s outer push rod at the jib cylinder at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.
Figure 4 – Greasing points on outer push rod at the jib cylinder
Greasing points on the push rod
Greasing points on the outer push rod
Section - 4 54 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Lubrication instructions
Re 3) For the T-Series:
Pins on the main boom: Lubricate the pins of the crane on the main boom at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.
Greasing points on the push rod
Lubrication instructions
Re 4) Sliding surfaces in the boom system:
Grease the boom system on all surfaces where the bearing slide blocks are running. I.e. grease the extensions externally on the underside and internally on the upper side.
Figure 5 - Boom system with indication of greasing points
The boom system has to be greased after 100 hours of operation or every month as a minimum. Furthermore the boom system has to be lubricated right before a longer period of standstill.
Grease the external underside
Grease the internal upper side.
Section - 4 55 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Change of slewing area
Change of slewing area
The present instructions are valid for the following loader cranes:
For the K-Series Cranes Catalogue
1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091
For the T-Series
Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101
These instructions describe how to change the slewing area of a ready-mounted crane.
It is important to mention that change of slewing area should be avoided by a necessary drawing up of the installation in connection with making the quotation and placing of the order. Otherwise expenses for changing the slewing area must be considered a direct economic loss for the seller (vendor).
Procedure:1. Take off the lubricating brush and the slewing sensor ( - if the crane is equipped with a
such). The components are fitted on the side of the central part of the base. Eachcomponent is fitted with two (2) x M6 screws.
Section - 4 56 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Change of slewing area
2. All hoses coming out of the column are removed from the control valve.
Figure 1 – Cover for lubricating brush on the side of the central part of the base.
Figure 2 – Hose connection for control valve
Section - 4 57 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Change of slewing area
3. Take off the protection plate. The plate is fitted with two (2) x M8 bolts with nuts.
4. Remove the hose clamp fixing the hoses at the protection plate.Please note:If there is no marking of the function of each individual hose, this has to be added beforedisassembling. It should also be marked where the hose clamp fixes the hoses. Thisshould be done to be able to recreate the correct length of each hose from the hose clampto the control valve.
Figure 3 – The underside of the crane with protection plate fitted.
Figure 4 – Hose routing through the underside of the column.
Section - 4 58 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
5. Loosen the hose connection and pull it downwards until the circlip on the bottom of thecolumn is visible and can be reached. The hose connection is fitted by means of four (4) xM8 button head screws. Take off the circlip on the bottom of the column.
6. It is now possible to lift up the column and place it again in the new slewing area required.Please note:Make sure that the column is free of the top and bottom bearings, when it has been raisedapprox. 75 mm. We recommend that lifting of the column with boom system is carried outas a two-point lift so that the burden is kept stable when it is no longer supported by thetop and bottom bearings. Otherwise bearings, coggings and hose connections may bedamaged.
Depending on the crane model, we recommend the following lift of the column inconnection with change of slewing area:
The K-Series:The 1300-K – 1830-K Series: 140 mm The 1800-K – 2630-K Series: 150 mm
The T-Series: The 1410-T - 1630-T Series: 140 mm The 1910-T - 2130-T Series: 150 mm
In the picture below, you see a cross-section through the lower part of a column and the central part of a base. You see the column lifted up to the area where the slewing area can be changed. Please note the dirt-repelling recess above the lower column bearing. If
Figure 5 – The underside of the crane with protection plate and hose connection removed.
Section - 4 59 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
the column is lifted too high, it will hit against the rack, if the column is not tilted away from the rack.
--- ooo ---
Assembling takes place in the opposite order as the items above. Make sure that the hose connections coming out of the column are positioned without the hoses being mutually twisted. This is how to ensure the longest possible life span of the hose routing inside the column.
Before tightening the hose clamp on the protection plate for fixing of hoses, each hose has to be positioned with correct length from the hose clamp to the control valve. This is to ensure that there is enough free hose length inside the column. (- this is used for instance in case of replacement of hoses.). In this connection it may be easiest to carry out the adjustment of the length of the hose by temporarily loosening and lifting the complete kit of hoses through the protection plate at the top of the column. Please see Service Information for replacement of hoses inside the column.
--- ooo ---
Figure 6 – Picture of the cross-section of the central part of a base with the column lifted.
Section - 4 60 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - Replacement of hydraulic hoses in column
Replacement of hydraulic hoses in column
The present instructions are valid for the following loader cranes:
For the K-Series Cranes Catalogue
1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091
For the T-Series
Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101
These instructions describe how to change hydraulic hoses in the column.
Replacement of hoses with internal hose routing inside the column is more demanding than for crane models with hose routing on the outside of the column. However, a longer life span for the internal hose routing and a more functional crane design compensates for this.
In case of urgent repair of hose rupture, carry out emergency repair as described in the Service Information no. 38 0XX 230 – “By-pass hose routing for emergency repair”.
If you have problems locating which one of the hoses that have been damaged it may be necessary to carry out a separate pressure test for each individual hose.
Procedure:
1. Dismount the hose shield at the top of the column.
Section - 4 61 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
2. Lift up the bundle of hoses either by means of a workshop crane or by means of the HMFservice tools P/N 82 00 030 (please see spare parts catalogue). When using the servicetools, fit the threaded pins into the hole plate for the bundle of hoses at the top of thecolumn. Then fit the service tools onto the flange at the top of the column. Thereuponconnect the threaded pins to the lifting tools. Dismount the screws at the back of thecolumn holding the hole plate. Then lift the bundle of hoses using the service tools. Nowthere is access to the hole plate with swivel coupling and hose ends.
Figure 1 – Photo of the upper part of the column with hose shield
Section - 4 62 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
3. Take off the end of the damaged hose from the swivel coupling on the hole plate. Screwthe end of the damaged hose together with the end of the new hose. (In case of limitedspace under the crane, it may be necessary to pull the new hose through using a string orthe like instead of direct connection to the damaged hose. This is because the rigid partnext to the connection cannot be turned out into the open at the bottom of the column).
Figure 2 – Photo of the top of the column with the bundle of hoses lifted using the service tools.
Section - 4 63 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
4. Dismount the protection plate underneath the base.
5. Take off the end of the damaged hose from the control valve.6. Loosen the clamp fixing the hoses at the protection plate to the point where the upper
hose end can come through.7. Pull out the damaged hose (- with the new one connected to the upper end) down through
the column. Pull the hose from below.8. Connect the hose ends to the swivel coupling on the hole plate as well as to the control
valve.9. Tighten the hose clamp and mount the protection plate.10. Lower the hole plate into the column and mount it again. Dismount the service tools.11. Mount the hose shield onto the column again.
In case of hose rupture you have to consider whether you should pull up the entire hose kit and change all hoses fed inside the column instead. One or several of the other hoses may also be worn and need replacement.
--- ooo ---
Change hoses led out of the front plate of the column for connection to the boom cylinder in the following way:
1. Dismount the hose connection on the load-holding valve on the boom cylinder.2. Take off the nuts on the front plate behind the boom cylinder. (It may appear easier to
dismount the lower pin in the boom cylinder and turn it away. The crane must be properlysupported before dismounting the pin).
3. Dismount both hose connections for the boom cylinder on the control valve.4. Tie the two lowest hose ends together with a string. This string must have a free end of at
least 2 metres.5. Pull out the hose kit from the top of the column.
Change the damaged hose, and both of them if necessary. To remount the hose/s, reverse the procedure.
--- ooo ---
Figure 3 – Photos of the protection underneath the base with and without protection plate.
Section - 4 64 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
1430 MCS - By-pass hose routing for emergency repair
The present information is valid for the following cranes:
For the K-Series
Cranes Catalogue1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091
For the T-Series
Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101
This information describes establishing of an emergency hose connection for the crane functions in case of hose rupture on the part of the crane’s hose routing that is fed inside the column.
The emergency hose connection can be used until you reach a service point.
The following hoses can be used for emergency purpose:
All permanent hose equipment, which is fitted on the crane, appears from the spare parts catalogue of the crane in question.
Hose connection from – to: Hose no.: Control valve – Boom “up/down” 00 15 250 Control valve – Jib ”extend/retract” 00 17 610 Control valve – Extension ”extend” (hole plate on jib) 56 524 Control valve – Extension ”retract” (hole plate on jib) 00 17 550 Control valve – Extra valves (hole plate on jib) 00 17 550 Control valve – Winch (hole plate on jib) 56 524
Section - 4 65 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
By-pass hose routing for emergency repair
In the following it is indicated in the photos how the different emergency hoses are fitted.
Figure 1 – Illustration of fitting of the hose loop from the control valve and further onto the crane. Please note the first fixing of the upper end of the hose loop on the boom cylinder as well as hydraulic connection down to the boom cylinder.
Figure 2 – Illustration of the hose routing further up to the connection on the jib cylinder.
Section - 4 66 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Cut off the part of the damaged hose placed below the main boom. Cut it as far to the back below the boom as you can reach, and take off the part of the hose which is fitted on the hole plate on the jib. Remove the piece of hose.
Instead of mounting by means of cable ties, it may be advantageous to fit the emergency hose under the hose clamps below the boom.
--- ooo ---
Figure 3 – Illustration of the hose routing further out under the main boom.
Section - 4 67 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Handling equipment Lifting yoke for handling of loader
The present instructions are valid for the following loaders:
Loaders Catalogue1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091
This information serves as instruction for safe internal handling of the loader in case of lifting when moving and mounting it on a truck, etc.
The figure 1 below shows a complete lifting yoke (82 00 010).
Spare parts numbers of the lifting yoke parts appear from the spare parts catalogue of the loader in question.
Figure 1 – Complete lifting yoke
Section - 4 68 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
The figure below shows the positioning of the lifting yoke in connection with lifting.
Figure 2 – Loader with lifting yoke seen from the side
Figure 3 – Loader with lifting yoke seen from the rear.
Section - 4 69 1430 MCS, Hydraulic Drawings
1430 MCS - Manual # 99906329
Lifting Instructions:
The max. permissible lifting capacity of the lifting yoke is 4.0 t.
The following instructions have to be followed when using the lifting yoke:
• The loader must be locked in stowing position while handling it by means of thelifting yoke. (Locking can take place by fitting of a pin in the stowing bracket or bysecuring of the main boom to the base).
• The lifting yoke is equipped with a row of holes used for attachment over thecentre of gravity of the loader. (cf. figure 3).
• Never lift the loader with a Fly-Jib fitted in the boom system.• When lifting, always keep at least a 5 metres safety distance from the loader.
The positioning of the centre of gravity of the loader depends on the loader configuration as regards the number of extensions and the equipment, etc. Therefore, the loader may, in certain loader configurations, not be completely in vertical position during lifting. In this connection, please pay attention to the fact that the loader may skid on the surface when it is lifted.
IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.
IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2021 Iowa Mold Tooling Co., Inc. All Right Reserved.
IOWA MOLD TOOLING CO., INC.
P.O. Box 189 Garner, IA 50438Tel: 641.923.3711
Fax: 641.923.2424www.imt.com