1/4 self-furred lath - plastic componentsplasticomponents.com/wp...lath-plus-instal-inst.pdf ·...

Installation Plastic Components ULTRA-LATH PLUS ™ Plastic Lath is designed as continuous reinforcement for stucco used in either exterior or interior wall applications. The 1/4" self- furring ridges provide exceptional keying and shall be installed with the ribbed surface against any code-approved substrate. It is lightweight and impervious to sand and any harsh chemicals found in portland-based stucco. WILL NEVER RUST OR CORRODE. Not for use on open framing or horizontal soffit applications. Splicing Lap a minimum of 1 inch (25 mm) and nail 6 inches (152 mm) on center. Overlapping Overlapping a minimum of 1/2 inch (13 mm) and either wire tie or use a cable tie at a minimum of 9 inches (229 mm) on center. On plywood sheathing, overlaps may be nailed or stapled in lieu of wire ties. Specification ULTRA-LATH PLUS ™ shall be Plastic Components, Inc. #PDM series. It shall be used where specified by the architect and installed per industry standards, and ASTM C1063, C1764, C1780, C1787 and C1788. ULTRA-LATH PLUS is recognized by IAPMO Uniform Evaluation Services report #0284 as code compliant to the 2009 and 2012 IBC and IRC. For questions regarding fire resistance, please contact our technical sales department. Patent pending / IAPMO Uniform Evaluation Report #0284 INSTALLATION INSTRUCTIONS 9051 NW 97th Terrace Miami, FL 33178 800.327.7077 • Fax 305.887.2452 • www.plasticomponents.com 1/4" Self-Furred Lath Instrucciones en español al dorso ©2008_REV 2014 Plastic Components Inc. in Sheets, Rolls and Strips Fasteners All fasteners should be installed with a minimum of 6 inches (152 mm) on center to the framing members or cementitious substrate. Nails or screws should be set flush to the ULTRA-LATH PLUS surface but do not countersink into the surface. Common nails should be bent over to engage a minimum of 3 strands of lath. Do not countersink. We recommend Plastic Components trims for all applications using ULTRA-LATH PLUS plastic lath. Type Size Length Head Roofing Nails #11 gauge 1" 7/16" (25 mm) (11 mm) Staples #14 gauge 1" 7/16" (25 mm) (11 mm) Common Nails #4d 1-1/2" 1/4" (38 mm) (6 mm) Stub Nails 3/8" to 1/2" 3/16" (10 to 13 mm) (5 mm) Screws Self-tapping 3/4" 5/16" wafer head (19 mm) (8 mm) MEETS ASTM C1764, C1780 C1784 C1787

Upload: others

Post on 11-Jul-2020

13 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: 1/4 Self-Furred Lath - Plastic Componentsplasticomponents.com/wp...Lath-Plus-instal-inst.pdf · Plastic Components ULTRA-LATH PLUS ™ Plastic Lath is designed as continuous reinforcement

SplicingLap a minimum of 1 inch (25 mm) and nail 6 inches (152 mm) on center.

OverlappingOverlapping a minimum of 1/2 inch (13 mm) and eitherwire tie or use a cable tie at a minimum of 9 inches (229 mm) on center. On plywood sheathing, overlapsmay be nailed or stapled in lieu of wire ties.

SpecificationULTRA-LATH PLUS™shall be Plastic Components, Inc.#PDM series. It shall be used where specified by the architect and installed per industry standards, and ASTM C1063, C1764, C1780, C1787 and C1788.ULTRA-LATH PLUS is recognized by IAPMO UniformEvaluation Services report #0284 as code compliant tothe 2009 and 2012 IBC and IRC.

For questionsregarding fireresistance,please contactour technicalsales department.

Patent pending / IAPMO Uniform Evaluation Report #0284

INSTALLATIONINSTRUCTIONS

9051 NW 97th Terrace Miami, FL 33178 800.327.7077 • Fax 305.887.2452 • www.plasticomponents.com

1/4" Self-Furred Lath

Instrucciones enespañol al dorso

in Sheets, Rolls and Strips

Fasteners

All fasteners should be installed with a minimum of 6 inches(152 mm) on center to the framing members or cementitioussubstrate. Nails or screws should be set flush to the ULTRA-LATH PLUS surface but do not countersink into the surface. Common nails should be bent over to engage a minimum of 3 strands of lath. Do not countersink.

We recommend Plastic Components trims for all applications using ULTRA-LATH PLUS plastic lath.

Type Size Length Head

Roofing Nails #11 gauge 1" 7/16"(25 mm) (11 mm)

Staples #14 gauge 1" 7/16"(25 mm) (11 mm)

Common Nails #4d 1-1/2" 1/4"(38 mm) (6 mm)

Stub Nails 3/8" to 1/2" 3/16"(10 to 13 mm) (5 mm)

Screws Self-tapping 3/4" 5/16"wafer head (19 mm) (8 mm)

MEETS

ASTMC1764, C1780

C1784

C1787

Prediction of the Maximum Dislocation Density in Lath ... of the Maximum Dislocation Density in Lath Martensitic Steel by Elasto-Plastic Phase-Field Method Zhenhua Cong1, Yoshinori