100 - bondioli & pavesi authorised dealer - · pdf file12 100 series 1b 1a 3 5 6 7 10 8 2...
TRANSCRIPT
100
PTO DRIVESHAFTS SERIES 100
100
400
652
662
80° 50°
70°
70°
2
SAFETY AND WORKING CONDITIONS
Disengage the PTO, turn off thetractor engine and remove key beforeapproaching the implement orperforming maintenance work.
When used at night or in poorvisibility, illuminate the drivelineoperating area.
Keep the driveline horizontal duringhandling to prevent the halves fromsliding apart, which could causeinjury or damage the shielding.Use suitable means to transportheavy drivelines.
CARDAN JOINTSWhen operating, ensure that joint angles are smalland equal: aCARDAN JOINTSWhen operating, ensure that joint angles are smalland equal: α1 = α2. During turns or other shortduration maneuvers, the maximum recommendedjoint angle is 45°. Disengage the PTO if the anglesare too large or not identical. 1 = a2. During turns orother short duration maneuvers, the maximumrecommended joint angle is 45°. Disengage the PTOif the angles are too large or not identical.
Never use the safety chains tosupport the driveline for storage.Always use the support on theimplement.
Do not stand on the driveline.Do not step over, or go under thedriveline.
Friction clutches may become hotduring use. Do not touch!Keep the area around the frictionclutch clear of any material whichcould catch fire and avoid prolongedslipping.
The tractor printed on the shieldindicates the tractor end of thedriveline. Any safety device shouldbe installed on the implement side.
1
2
1
2
Telescoping tubes must alwaysoverlap by at least 1/2 of their lengthin normal operation and at least 1/3of their length in all workingconditions.During maneuvers, when the drivelineis not rotating, the telescoping tubesmust have a suitable overlap tomaintain the tubes aligned and allowthen to slide freely.
All rotating parts must be shielded.The tractor master shield, the driveline guard,and the implement shield all work togetherfor your safety. Do not operate without alldriveline, tractor and implement shields inplace. Damaged or missing parts must berepaired with original spare parts or replacedbefore using the driveline. The driveline mustbe securely attached at both ends. Guardsmust turn freely on the driveline.
Ensure that the driveline is securelyattached to the tractor and theimplement before operating.Check that all fixing screws are tight.
Keep clear of the work area androtating parts. Do not wear looseclothing, jewelry, or hair that couldbecome entangled with the driveline.Contact with rotating parts can causeserious injury or death.
When using the implement and thedriveline, do not exceed the speedor power limits specified in theoperator’s manual. Do not overloadthe implement or suddenly engagethe PTO clutch. Any torque limiter orclutch must be installed on theimplement end of the driveline. Usethe implement only with the originaldriveline, which is fit for the purposein terms of length, dimensions,devices and shields.
The driveline and its torque limiter oroverrunning clutch are designedspecifically for the implement, andshould be used exclusively for thispurpose. Check the implementinstruction handbook to ascertainwhether the driveline must beequipped with a torque limiting oroverrunning clutch. Standarddrivelines, torque limiters andoverrunning clutches are designedfor speeds of up to 1000 rpm.
Ensure that the driveline can performall operations without interfering withthe tractor or the machine. Contactwith parts of the tractor, hooks, drivepins, tires, drawbar, hammerstrap, or3-point hitch, will damage the guard.Never use tractors, (or systems forconnection to the implement) thatinterfere with the driveline duringoperation. Do not use adapters orcomponents not offered by theimplement manufacturer.
CONSTANT VELOCITY JOINTSFor normal operations, it is best to keep the CV jointaligned or with the smallest joint angle possible.During turns or other short duration maneuvers, themaximum joint angle is 50°, 70° (Constant VelocityJoint 652) or 80° according to the design of the CVjoint. When the driveline includes a CV joint on thetractor side and a single U-joint on the implementside, the maximum recommended angles of the U-joint are 16° at 540 rpm and 9° at 1000 rpm to avoiddrive irregularities.
Attach the driveline guard restraints(chains). Best results are achieved whenchains are attached nearly perpendicularto the driveline guard. Adjust the lengthof the chains to allow enough slack forfull movement of the driveline during turns,operation, and transport. Avoid excessiveslack, which could cause the chains toroll around the driveline.
7LRS/R006 100 SERIES
L
L 1/2 L
DRIVELINE SAFETYThe safety of the end user dependsupon proper use and maintenanceof the implement, tractor, anddriveline, plus all related safetyshielding. Information regardingcorrect driveline usage is includedon the safety label and in the useand maintenance manual includedwith Bondioli & Pavesi drivelines.Safety labels and user’s manuals inalternative languages are availableto meet local requirements.If drivelines are to be used onmachines bound for export, contactBondioli & Pavesi for labels andmanuals. The manufacturer orpurchaser must inform Bondioli &
Pavesi when alternative labels ormanuals are required.Read the driveline manual, and theoperator’s manual for the implement,before using the machine.YOUR SAFETY DEPENDS UPONTHIS INFORMATION.
Drivelines sold in North America(USA, Canada and Mexico) areequipped with safety labels code
399141000 and 399143000 and havethe user’s manual code 399USA010.
OUTER LABEL
399141000INNER LABEL
399143000INSTRUCTION BOOKLET
399USA010
DRIVELINES FOR NORTH AMERICA(USA, Canada and Mexico)
The primary driveline (the one thatconnects the tractor to the machine)sold in ECC and EFTA countries havethe CE mark, safety label code
399CEE051 and 399143000, usermanual code 399CEE010 and safetychains.
OUTER LABEL
399CEE051INNER LABEL
399143000INSTRUCTION BOOKLET
399CEE010
PRIMARY DRIVELINES FOR EEC-EFTA COUNTRIES
399CEE051
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
399143000
XXX
XXXX
XXX
XXXX
399CEE010
399141000
DANGER
3991
4100
0
ROTATING DRIVELINECONTACT CAN CAUSE DEATH
KEEP AWAY!DO NOT OPERATE WITHOUT -
DRIVELINES SECURELYATTACHED AT BOTH ENDS
ALL DRIVELINE GUARDS, TRACTORAND EQUIPMENT SHIELDS IN PLACE
DRIVELINE GUARDS THAT TURNFREELY ON DRIVELINE
399143000 399USA010
8 LRS/R006 100 SERIES
cod
. 399
CE
E01
0
M A D E I N I T A L Y
cod
. 399
US
A01
0
M A D E I N I T A L Y
OUTER LABEL399CEE051
INNER LABEL399143000
INSTRUCTION BOOKLET399USA010
CE - SAFETY FEATURES
XXX
XXXX
NON-PRIMARY DRIVELINES FOR EEC/EFTA COUNTRIESAND DRIVELINES FOR NON-EEC/EFTA COUNTRIES
Drivelines internal to the machine orsold to non-EEC/EFTA countries donot require the CE mark. They areequipped with safety labels code
399CEE051 and 399143000, andhave the users manual code399USA010.
Driveline identification, CE mark
Operating instructions, CE-Declarationof Conformity
Safety labelon shield tube
Safety labelon telescoping members
Cone length at least to the endof the inboard joint
Cone length at least to the endof the outer joint
Safety chains
Torque limiters or overrunning clutchon the implement side only
The implement must provide PIC shielding
Minimum overlapin straight position
Support for the PTO drive shaftwhen the machine is uncoupled
Tractor master shield
9
10
11
12
2
3
4
1 5
6
7
8
399143000 399USA010399CEE051
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
LRS/R006 100 SERIES 9
11
7 7
cod
. 399
US
A01
0
M A D E I N I T A L Y
XXX
XXXX
min. 50 mm
XXX
XXXX
min. 50 mm
125
61 4 10
893
cod.
399
CE
E01
0
M A D E I N I T A L Y
2
cod.
399
CE
E01
0
M A D E I N I T A L Y
2
LUBRICATION INTERVALS - HOURS
LRS/R006 100 SERIES
AFTER ANY MAINTENANCE OR REPAIR, ALWAYS REPLACE ALL GUARDS AND SHIELDS!
10
Overrunning clutches RA2Overrunning clutches RA1
50
80° 50°
50
50
70°
50 508
8
Ratchet torque limiters SA
50
Ratchet torque limiters LN
50
Shear bolt torque limiters LB
SEASONALLUBRICATION
FNT
50
FFNV
50
FNV
50
50
Combination friction torque limiter and overrunning clutch
11LRS/R006 100 SERIES
WEAR OF YOKE EARS
EXCESSIVE WORKING ANGLE
• Reduce working angle.
• Disengage PTO when joint angleexceeds 45°.
DEFORMATION OF YOKE EARS
EXCESSIVE TORQUE PEAK ORSHOCK LOAD
• Avoid overloading and engagingdrive under load.
• Check function of torque limiter.
CROSS ARMS BROKEN
EXCESSIVE TORQUE PEAKOR SHOCK LOAD
• Avoid overloading and engagingdrive under load.
• Check function of torque limiter.
ACCELLERATED WEAROF CROSS ARMS
EXCESSIVE LOAD
• Do not exceed the speed orpower limits indicated in theinstruction manual.
INSUFFICIENT LUBRICATION
• Follow instructions in chapter“Lubrication and maintenance”.
SEPARATION OFTELESCOPING TUBES
EXCESSIVE EXTENSIONOF DRIVELINE
• Avoid excessive extension ofdriveline.
• For stationary machinery: positionthe tractor so that the telescopingtubes overlap as illustrated inchapter “Working conditions”.
• Check extension of drawbar hitchaccording to the instruction manual.
DEFORMATION OFTELESCOPING TUBES
EXCESSIVE TORUQE PEAKOR SHOCK LOAD
• Avoid overloading and engagingdrive under load.
• Check functioning of torque limiter.
• Check that driveline does not comeinto contact with tractor or implementcomponents during movement.
ACCELERATED WEAR OFTELESCOPING TUBES
INSUFFICIENT LUBRICATION
• Follow instructions in chapter"Lubrication Intervals."
INSUFFICIENT TUBE OVERLAP
• Follow instruction in chapter"Safety and working conditions."
ACCELERATED WEAR OFSHIELD BEARING
INSUFFICIENT LUBRICATION
• Follow instructions in chapter"Lubrication intervals."
TROUBLESHOOTING
TECHNICAL DATA 100 SERIESS
IZE
kW HP
18
23
35
40
40
54
74
87
110
140
170
25
31
47
55
55
74
100
118
150
190
230
540 min-1 1000 min-1
1
2
3
4
5
6
7
8
9
10
43
kW
12
15
22
26
26
35
47
55
70
88
106
HP
16
21
30
35
35
47
64
75
95
120
145
A 22 - B 54
41201R50
A 23,8 - B 61,3
41202R30
A 27 - B 70
41203R25
A 27 - B 74,6
41204R25
A 30,2 - B 79,4
41205R40
A 30,2 - B 91,4
41206R30
A 35 - B 93,5
41207R24
A 35 - B 106
41208R20
A 41 - B 108
41209R10
A 41 - B 118
41210R10
A 27 - B 74,6
41204R25
63,5
70
79,5
84
84
91
103
106
117
119
130,5
A 22 - B 54
4120B0011R50
A 23,8 -B 61,3
4120C0011R30
A 27 - B 74,6
4120E0011R25
A 30,2 - B 79,4
4120G0011R40
A 30,2 - B 91,4
4120H0011R30
A 35 - B 93,5
4120L0011R24
A 35 - B 106
4120M0011R20
A 27 - B 74,6
4120E0011R25
For jointsproduced prior
to 2005
2aCARDANJOINTS
A B
2CARDANJOINTS
A B
For jointsproduced
starting 2005
A 22 - B 86
4120E0051R40
A 27 - B 100
4120G0051R30
A 30,2 - B 106
4120L0051R20
---
---
---
---
---
18CV JOINTS
A B
---
100-400G-DG-GF
H
PACKAGE QUANTITIES: THE NUMBER FOLLOWING THE LETTER "R" IN THE CODE INDICATESTHE NUMBER OF PIECES IN EACH PACK. FOR EXAMPLE, 341036000R10 INDICATES THATEACH PACKAGE CONTAINS 10 ROLL PINS.
SIZE 3, 9, AND 10 DRIVELINES ARE NO LONGER IN PRODUCTION. ONLY SPARE PARTS FOR THESE SIZES ARE AVAILABLE.
8 50
---
---
---
50
---
---
Power Rating
12
100 SERIES
1b
1a
3 5 6 7 10 8
211
1a
1b
2
LRS/R006 100 SERIES
2a2a
100 - 400 SERIES
* Yokes in size 3, 9, and 10 are only available with RS TwistCollar connection.
The codes for the tubes reference the 3 meter lengths packaged in multiples of 6 pieces.Normally, tubes as spare parts are sold in lengths of 1 meter.
4 9
BA BA
SHROUDED QD1 3/8" Z6
OUTERTUBE YOKE
JOINT FOROUTER TUBE
ROLL PIN FOROUTER TUBE
OUTERDRIVE TUBE
INNERDRIVE TUBE
INNERTUBE YOKE
1a 3 4 5 6 7 8
A 2,6 - B 32,5 A 4 - B 26,5
125033000R06 125023000R06
A 3,2 - B 36 A 4 - B 29
125053000R06 125043000R06
A 3,4 - B 43,5 A 4 - B 36
125083000R06 125073000R06
A 3 - B 51,5 A 3,8 - B 45
125103000R06 125973000R06
A 4 - B 54 A 4,2 - B 45
125123000R06 125093000R06
A 4 - B 54 A 5,5 - B 45
125123000R06 125113000R06
A 4 - B 63 A 4 - B 54
125223000R06 125123000R06
A 4 - B 63 A 5 - B 54
125223000R06 125133000R06
A 5,6 - B 66 A 6 - B 54
125153000R06 125143000R06
A 3,4 - B 43,5 A 3,2 - B 36
125083000R06 125053000R06
JOINT FORINNER TUBE
91b
Guards removed for illustration purposes only.Make sure all driveline, tractor, and equipment shields are in place before operation.
ø ø
A 3,4 - B 43,5
125083000R06
A 3,2 - B 36
125053000R06
BALL COLLAR1 3/8" Z6
5720B0355 341036000R10
341048000R10
341038000R10
341038000R10
341038000R10
341053000R10
341042000R10
341042000R10
341054000R10
341054000R10
341044000R10
204016852
204026852
204046852
204046852
204056861
204066852
204176852
71G1049007
71G2049007
71G4049007
71G4049007
71G5049007
71G6049007
71G7049007
71G8049007
71G1050007
71G2050007
71G4050007
71G4050007
71G5050007
71G6050007
71G7050007
71G8050007
572030351*
572030361*
572090351*
572090361*
572100351*
572100361*
204036851
204196851
204106851
71G3049T07*
71G9049T07*
71G0049T07*
204036852
204196852
204106852
71G9050S07*
71G0050S07*
71G3050S07*
204086861
204086888**
Ø 40
Ø 47
Ø 53
Ø 53
Ø 62
Ø 68
Ø 68
Ø 80
Ø 34
Ø 40
Ø 46
Ø 53
Ø 59
Ø 59
Ø 46
---
---
---
Ø 68
5070B0355
5070C0355
5070E0355
5070E0355
5070G0355
5070H0355
5070L0355
5070M0355
5720C0355
5720E0355
5720E0355
5720G0355
5720H0355
5720L0355
5720M0355
204016851
204026851
204046851
204046851
204056860
204066851
204176851
204086860
** For drive shafts equipped with CV joint at the opposite site.
204043251
204053361
204063361
204173451
204083460
345013000R10
345012000R10
345001000R10
345001000R10
345002000R10
569B40720
569B50710
569B60700
569B70700
569B80690
400 SERIES
LRS/R006 100 SERIES 13
1 Code refers to a length of 810 mm (081 code)2 Complete the code wth the length expressed in millimeters.
12a3
INNER YOKESPLINED
14
WELD YOKEROUND TUBE
JOINT FORSPLINED BAR
15
204025353
204045353
204055353
204065352
204175351
204085361
204015353
SPLINEDBAR
132
Ø 30 - Z 10
24917....
Ø 35 - Z 12
24911....
Ø 35 - Z 12
24911....
Ø 40 - Z 14
24921....
Ø 40 - Z 14
24921....
ROLL PIN FORINNER TUBE
10
YOKE & SPLINEDSLEEVE ASSEMBLY
121
ROUND TUBE
13678....
13678....
13679....
13679....
13680....
13680....
13681....
13681....
13674....
13674....
12b2,3 12c3
SPLINED SLEEVE
226003101R05
226003101R05
226003201R05
226003201R05
226003301R05
226003301R05
226003401R05
226003401R05
226008101R05
226008101R05
3 Weld yoke (12a), round tube (12b), and splinedsleeve (12c) are not available in North America.
---
---
---
---
---
---
---
---
---
---
--- --- --- --- ---
--- ---
ø
16
ROLL PIN FORSPLINED BAR
ø
Guards removed for illustration purposes only.Make sure all driveline, tractor, and equipment shields are in place before operation.
Ø 46
Ø 53
Ø 59
Ø 59
Ø 68
Ø 25 - Z 10
24915....
Ø 25 - Z 10
24915....
Ø 30 - Z 10
24917....
341037000R10
341036000R10
341048000R10
341048000R10
341048000R10
341002000R10
341043000R10
341043000R10
341055000R10
341055000R10
341045000R10 ---
--- 204195351
204105351
204035353 71G3059S07*
71G9059S07*
71G0059S07*
71G1059007
71G2059007
71G4059007
71G5059007
71G6059007
71G7059007
71G8059007
16 14
12a 12b 12c1b
1a
211
1a
1b
2
2a 2a
12 13
15
---
---
---
---
---
---
5070B3755
5070C3755
5070E3755
5070E3755
5070G3755
5070H3755
5070L3755
5070M3755
14 LRS/R006 100 SERIES
---
---
---
---
1 - 2
---
---
408000075R
408000075R
43 - 4408000075R
408000075R
408000076R
408000076R
5408000075R
408000075R
408000076R
408000076R
6408000075R
408000075R
408000076R
408000076R
7408000075R
408000075R
408000076R
408000076R
8
---
---
408000060
408000060
3
408000061
408000061
408000060
408000060
9 - 10
(B)
(A)(C)
403000021R10
403000021R10
---
---
1 - 2403000001R10
403000001R10
---
---
43 - 4403000001R10
403000001R10
---
---
5403000001R10
403000001R10
---
---
6403000032R10
403000032R10
---
---
7403000032R10
403000032R10
---
---
8403000001R10
403000001R10
---
---
3 9 - 10403000013R10
403000013R10
403000012R10
403000012R10
YOKES FOR CARDAN JOINTS
QUICK DISCONNECT (QD) PINS
TAPERED PIN KITS
* Yokes in size 3, 9, and 10 are only available with RS Twist Collar connection.
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
5720B3776
5720C3776
5720E3755
5720E3755
5720G3755
5720H3755
5720L3755
5720M3755
--- ---
--- ---
--- ---
--- ---
5720G0455 5720G3855
5720H0455 5720H3855
5720L0455 5720L3855
5720M0455 5720M3855
--- --- --- ---
--- --- --- ---
--- ---
--- ---
--- --- --- --- --- --- ---
1 3/8" Z21
1a 1b 11
1 3/8" Z21 1 3/4" Z6 1 3/4" Z20 1 3/8" Z21 1 3/4" Z6 1 3/4" Z201 3/8" Z6
SHROUDED QD BALL COLLAR TAPER PIN
5090E0360
5090E0360
5090G0360
5090H0360
5090L0360
5090M0360
5090E3760
5090G3760
5090H3760
5090H3760
5090L3760
5090M3760
5090G0460
5090H0460
5090L0460
5090M0460 5090M3860
5090L3860
5090H3860
5090G3860
572033751*
572033761*
572093751*
572093761*
572103751*
572103761*
---
---
---
---
---
---
---
---
---
---
---
---
---
---
ATTENTION - Use pin that fits completely into hub. Discard other pins and nut. Use tapered nut ONLY with pin (C) and yoke with counter-sunk hole.
15LRS/R006 100 SERIES
f
c
d
eb
a
a
b1
e
c
dØd
Øa
c
e
b
403000020R10
403000001R10
403000009R10
403000002R10
403000010R10
403000008R10
403000012R10
403000011R10
---
---
---
---
---
8
8
8
8
8
8
8
8
---
---
---
---
---
37,2
47
54
65,5
66,5
57,5
60
68,5
---
---
---
---
---
23
27
27
38,5
37,5
29,5
35
38
---
---
---
---
---
14,2
20
27
27
29
28
25
30,5
---
---
---
---
---
13,85
13,85
13,85
13,85
13,85
15,85
15,85
15,85
---
---
---
---
---
Øa b c e Ød Code
401000001R10
401000002R10
401000006R10
401000009R10
401000028R10
401000033R10
401000007R10
401000021R10
401000010R10
401000026R10
401000037R10
401000003R10
401000011R10
29,5
29
34,5
28,5
32
32
28,5
30
33
33,5
33
-
-
11
10
11
10
10
13,5
9,5
13
14
13,5
9,5
13
13
12
14,5
12
22,5
22,5
13
22
14,5
15
15,5
22
11
11,5
22
21
22
20
27
33
23,5
26
25
32
30
11
13
74,5
74,5
79,5
81
91,5
91,5
83,5
83,5
87
94,5
94,5
35
37,5
13,85
13,85
13,85
13,85
13,85
13,85
15,85
15,85
15,85
15,85
15,85
12,85
12,85
Øa b/b1 c d e f Code
(034) (035) (036)(053) (054) (055) (056)
A
F
A
F
(090) (091) (095)
A 25 - F 8 A 30 - F 8 A 25 - F 8 A 30 - F 8 D 74,5 - E 8,5 D 47,5 - E 8,5
212016151 212016251 509016152 509016252 221017153 221017251
A 25 - F 8 A 30 - F 8 A 25 - F 8 A 30 - F 8 D 74,5 - E 8,5 D 74,5 - E 8,5
212026151 212026251 509026152 509026252 221027153 221027251
A 25 - F 8 A 30 - F 8 A 35 - F 10 A 25 - F 8 A 30 - F 8 A 35 - F 10 D 84 - E 10,5 D 74,5 - E 8,5 D 84 - E 10,5
212036151 212036251 212036351 509036152 509036252 509036352 221037153 221037152 221037251
A 25 - F 8 A 30 - F 8 A 35 - F 10 A 25 - F 8 A 30 - F 8 A 35 - F 10 D 84 - E 10,5 D 74,5 - E 8,5 D 84 - E 10,5
212046151 212046251 212046351 509046152 509046252 509046352 221047153 221047152 221047251
A 30 - F 8 A 35 - F 10 A 40 - F12 A 30 - F 8 A 35 - F 10 D 94 - E 10,5 D 84 - E 10,5 D 94 - E 10,5
212056251 212056351 212056451 509056252 509056352 221057153 221057152 221057251
A 30 - F 8 A 35 - F 10 A 40 - F 12 A 30 - F 8 A 35 - F 10 D 101,5 - E 12,5 D 94 - E 10,5 D 101,5 - E 12,5
212066251 212066351 212066451 509066252 509066352 221067153 221067152 221067251
A 30 - F 8 A 35 - F 10 A 40 - F 12 A 35 - F 10 D 120 - E 15 D 120 - E 15
212176551 212176351 212176451 509176352 221177151 221177252
A 35 - F 10 A 40 - F 12 A 35 - F 10 D 120 - E 15 D 120 - E 15
212086351 212086451 509086352 221087153 221087251
A 40 - F 12 D 150 - E 17 D 150 - E 17
212196451 221197151 221197251
A 40 - F 12 D 150 - E 17 D 150 - E 17
212106451 221107151 221107251
A 25 - F 8 A 30 - F 8 A 35 - F 10 A 25 - F 8 A 30 - F 8 A 35 - F 10 D 84 - E 10,5 D 74,5 - E 8,5 D 84 - E 10,5
212046151 212046251 212046351 509046152 509046252 509046352 221047153 221047152 221047251
D
E
90°
E
60° 60°
D
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
ROUND BORE ROUND BORE - INTERFERRING CLAMP BOLT FLANGE YOKE
Push pins come packaged with springs and clips (if required).
435000320R
435000300R
---
---
435000320R
435000300R
---
---
435000321R
435000321R
---
---
435000321R
435000321R
435000418R
435000418R
435000321R
435000321R
435000418R
435000418R
435000322R
435000322R
435000419R
435000419R
435000322R
435000322R
435000419R
435000419R
16 LRS/R006 100 SERIES
1 2 43 - 4 5 6 7 8
SINGLE AND DOUBLE JOINTS
BALL COLLAR REPAIR KITS
Single and double joints listed below have a 1-3/8" Z6 shrouded push pin (QD) yoke and a 1-3/8" Z6 splined yoke. Other combinations are available - please inquire.
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
71G1027007
71G2027007
---
71G4027007
71G5027007
71G6027007
71G7027007
71G8027007
---
7GF1027007
7GF2027007
7GF4027007
7GF5027007
7GF6027007
7GF7027007
7GF8027007
7DG1027007
7DG2027007
7DG4027007
7DG5027007
7DG6027007
I
R
I
R
I 68 - R 75
I 78 - R 82
I 90 - R 96
I 106 - R 103
I 108 - R 115
---
---
---
---
---
---
---
---
---
---
---
---
I 98 - R 90
I 108 - R 90
I 128 - R 100
I 136 - R 110
I 154 - R 130
I 158 - R 148
I 158 - R 148
17LRS/R006 100 SERIES
Complete the code with the length in mm*
L
D1
L
262000106R02 226000105R05
226000106R05
226000305R05
262000345R02
226000306R05
226000405R05
262000415R02
226000406R05
LL
90
90
90
80
100
80
100
80
100
226000327R05 130
1 1/8" Z61 3/8" Z61 3/4" Z6
1 1/8" Z61 3/8" Z61 3/4" Z6
*14931....
14933....
14934....
1 1/8" Z61 1/8" Z61 3/8" Z61 3/8" Z61 3/8" Z61 3/4" Z61 3/4" Z6
D1
ACCESSORIES
18
100 SERIES DRIVESHAFTS
COMPLETE DRIVESHAFTS
LRS/R006 100 SERIES
100 SERIES
Codes above are equipped with CE mark (includes CE labels, instructions, and declaration of conformity).For other countries, the "CE" may be replaced by "UC" (for North America), "JP" (for Japan), or "FX", which will have labelsand instructions according to pages 7-8.
L
7101061CE007007
7102061CE007007
7143061CE007007
7104061CE007007
7105061CE007007
7106061CE007007
7107061CE007007
7108061CE007007
---
061
610
---
---
7101086CE007007
7102086CE007007
7143086CE007007
7104086CE007007
7105086CE007007
7106086CE007007
7107086CE007007
7108086CE007007
---
086
860
---
---
7101121CE007007
7102121CE007007
7143121CE007007
7104121CE007007
7105121CE007007
7106121CE007007
7107121CE007007
7108121CE007007
---
121
1210
---
---
19
400 SERIES DRIVESHAFTS
COMPLETE DRIVESHAFTS
LRS/R006 100 SERIES
400 SERIESL
7404051CE007007
7405051CE007007
7406051CE007007
7407051CE007007
7408051CE007007
7404056CE007007
7405056CE007007
7406056CE007007
7407056CE007007
7408056CE007007
7404061CE007007
7405061CE007007
7406061CE007007
7407061CE007007
7408061CE007007
7404066CE007007
7405066CE007007
7406066CE007007
7407066CE007007
7408066CE007007
7404071CE007007
7405071CE007007
7406071CE007007
7407071CE007007
7408071CE007007
7404076CE007007
7405076CE007007
7406076CE007007
7407076CE007007
7408076CE007007
7404081CE007007
7405081CE007007
7406081CE007007
7407081CE007007
7408081CE007007
510
051
560
056
610
061
660
066
710
071
760
076
810
081
Codes above are equipped with CE mark (includes CE labels, instructions, and declaration of conformity).For other countries, the "CE" may be replaced by "UC" (for North America), "JP" (for Japan), or "FX", which will have labelsand instructions according to pages 7-8.
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
208026873 208026874
20
70° CV JOINT
650 SERIES CV DRIVELINES IN SIZES 4, 6, AND 8 ARE NO LONGER IN PRODUCTION - AVAILABLE ONLY AS COMPONENT PARTS.
LRS/R006 100 SERIES
650 - 660 - 670 SERIES CV JOINT DRIVESHAFTS
21
The codes for the tubes reference the 3 meter lengths packaged in multiples of 6 piecesNormally, tubes as spare parts are sold in lengths of 1 meter.
BA
80° EL CVJOINT - INNER
CV BODY
26
HARDSHELLCONE WITHBEARINGS
HARDSHELLBEARING RINGS
17 27
1 3/8" Z680° EL CV
JOINT - OUTER
21 25 22
OUTER DRIVETUBE RILSAN
BA
23
INNER DRIVETUBE RILSAN1 3/8" Z21
19
CV OUTERTUBE YOKE
20 24
CV INNERTUBE YOKE
573020379
573040382
573060399
573080399
---
---
---
---
---
573023764
573043775
573063781
573083799
---
---
---
---
---
512020051
511040051
511060051
511080051
---
---
---
---
---
215046873
215066872
215086870
---
---
---
---
---
215046874
215066871
215086869
---
---
---
---
---
7G52049R07
7G54049T07
7G56049T07
7G58049T07
---
---
---
---
---
7G52050R07
7G54050S07
7G56050S07
7G58050S07
---
---
---
---
---
---
A 2,9 - B 36
125183000R06
A 3,1 - B 43,5
125163000R06
A 3,7 - B 54
125173000R06
A 3,7 - B 63
125213000R06
---
---
---
---
A 4,3 - B 29,6
245043000R06
A 4,8 - B 36,6
245103000R06
A 4,3 - B 45,6
245163000R06
A 4,3 - B 54,6
245693000R06
---
---
---
---
---
517027012
517048001
517068001
517088001
---
---
---
---
---
255020402
255040351
255060351
255080351
---
---
---
---
---
ø1 øø
ø1 ø1BALL COLLAR
Guards removed for illustration purposes only.Make sure all driveline, tractor, and equipment shields are in place before operation.
A 23,8 - B 61,3
41202
A 23,8 - B 86
412040012
A 30,2 - B 99,4
412060012
A 35 - B 106
412080012
-
-
-
-
-
18a
A B
8
20
18a 19 18a
2627
22 23 24
5 10
18a 1917 18a 17
25
Ø1 18 Ø 47 Ø1 18Ø1 18
Ø1 24 Ø1 24
Ø1 26 Ø1 26
Ø1 28 Ø1 28
Ø 40 Ø1 18
Ø 53 Ø1 24 Ø 46 Ø1 24
Ø 68 Ø1 26 Ø 59 Ø1 26
Ø 80 Ø1 28 Ø 68 Ø1 28
LENGTHL (mm)
CODE
LENGTHL (mm)
CODE
21LRS/R006 100 SERIES
662
652
652
1010
101
1210
121
810
081
662
810
081
1010
101
1210
121
7652081CER07007 7652101CER07007 7652121CER07007
7662081CE007R07 7662101CE007R07 7662121CE007R07
650 SERIES COMPLETE DRIVESHAFTS
70° L
70°L
Codes above are equipped with CE mark (includes CE labels, instructions, and declaration of conformity). For other countries, the "CE"may be replaced by "UC" (for North America), "JP" (for Japan), or "FX" which will have labels and instructions according to pages 7-8.
5730E0384
5730G0384
5730L0384
5110E0052
5110G0061
5110L0063
2150E6885
2150G6885
2150L6873
341038000R10
341042000R10
341054000R10
2150E6887
2150G6887
2150L6874
71G4W49WR7
71G6W49WR7
71G8W49WR7
71G4W50WR7
71G6W50WR7
71G8W50WR7
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
22
100 SERIES 80° CV JOINT
LRS/R006 100 SERIES
100 SERIES 80° CV JOINT
30 32 38
CV BODY 80° EL CVJOINT - INNER
80° EL CVJOINT - OUTER1 3/8" Z6
28
ROLL PINFOR OUTER TUBE
33
CV OUTERTUBE YOKE
31
CV INNER TUBE YOKE
36
ø1 ø1 ø ø1ø
BALL COLLAR
Guards removed for illustration purposes only.Make sure all driveline, tractor, and equipment shields are in place before operation.
32
31
28
18 30 18
33
3429
40a
Ø 53 Ø1 24Ø1 24
Ø1 28
Ø1 34
Ø 68 Ø1 28
Ø 80 Ø1 34
Ø 46 Ø1 24
Ø 59 Ø1 28
Ø 68 Ø1 34
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
341048000R10
341053000R10
341054000R10
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
23LRS/R006 100 SERIES
2550E0005R02
2550G0024R02
2550L0023R02
2190E0127
2190G0150
517080200
254040020
254060020
254080033
254040021
254060021
254080034
The codes for the tubes reference the 3 meter lengths packaged in multiples of 6 pieces.Normally, tubes as spare parts are sold in lengths of 1 meter.
OUTER DRIVETUBE RILSAN
34
INNER DRIVETUBE RILSAN
35*
ROLL PINFOR INNER TUBE
39 41
CV SHIELD CONEBEARING RING
40
SHIELDCONE
A 3,1 - B 43,5 A 4,3 - B 36,6
125163000R06 245103000R06
A 3,7 - B 54 A 4,5 - B 45,6
125173000R06 245163000R06
A 3,7 - B 54 A 5,8 - B 45,6
125173000R06 245393000R06
BA BA
CONE FOR INNER TUBECONE FOR OUTER TUBE
40a 40b
39
3635
40 41
18 1830
28
29
37
38 40b
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
5730E0353
5730G0353
5730L0353
2080E0055
2080G0064
2080L0064
2080E6876
2080G6885
2080L6864
341038000R10
341042000R10
341054000R10
2080E6875
2080G6887
2080L6865
71G4K49KR7
71G6K49KR7
71G8K49KR7
71G4K50KR7
71G6K50KR7
71G8K50KR7
246000101
246000116
246000116
---
---
---
---
---
---
24
50° CV JOINT
LRS/R006 100 SERIES
43 47
100 SERIES 50° CV JOINT
46
43 46 47
50° EL CVBODY
50° EL CVJOINT INNER
50° EL CVJOINT OUTER1 3/8" Z6
ROLL PINOUTER TUBE
CV OUTERTUBE YOKE
CV INNERTUBE YOKE
44 45 50 52
184418 48
45
44a
44a
RUBBER BOOT
ø1 ø ø
54b
BALL COLLAR
Guards removed for illustration purposes only.Make sure all driveline, tractor, and equipment shields are in place before operation.
Ø1 29
Ø1 33
Ø1 33
Ø 53
Ø 68
Ø 80
Ø 46
Ø 59
Ø 68
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
341048000R10
341053000R10
341054000R10
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
25LRS/R006 100 SERIES
53
51
43
2550E0005R02
2550G0024R02
2550L0023R02
254040020
254060020
254080033
254040021
254060021
254080034
55
The codes for the tubes reference the 3 meter lengths packaged in multiples of 6 pieces.Normally, tubes as spare parts are sold in lengths of 1 meter.
BA BA
48
OUTER DRIVE TUBE
49
CV SHIELD CONEBEARING RING
---
---
---
---
---
---
2190E0126
2190G0153
2190L0123
54
SHIELDCONE
A 3,4 - B 43,5 A 4 - B 36
125083000R06 125073000R06
A 4 - B 54 A 4,2 - B 45
125123000R06 125093000R06
A 4 - B 54 A 5,5 - B 45
125123000R06 125113000R06
53
ROLL PININNER TUBE
49 18 44 18
52
50
44a
INNER DRIVE TUBE CONE FOR INNER TUBECONE FOR OUTER TUBE
54a 54b
54 5554b
5730E3784
5730G3784
5730L3784
5730E0484 5730E3884
5730G0484 5730G3884
5730L0484 5730L3884
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
5730E0391
5730G0391
5730L0391
5730E3791
5730G3791
5730L3791
5730E0491
5730G0491
5730L0491
5730E3891
5730G3891
5730L3891
5110E0361
5110G0361
5110L0361
5110E3761
5110G3761
5110L3761
5110G0461
5110L0461
5110G3861
5110L3861
--- ---
435000323R
435000323R
435000420R
453000420R
435000323R
435000323R
435000420R
435000420R
435000323R
435000323R
435000420R
435000420R
435000311R
435000311R
435000411R
435000411R
435000311R
435000311R
435000411R
435000411R
435000311R
435000311R
435000411R
435000411R
26 LRS/R006 100 SERIES
4 6 8
4 6 8
YOKES FOR 100 SERIES 80° EL CV
BALL COLLAR REPAIR KITS FOR 80° - 50° EL CV
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
AUTOMATIC BALL COLLAR REPAIR/RETROFIT KITS FOR 80°-50° EL CV
1 3/8" Z21 1 3/4" Z6 1 3/4" Z20 1 3/8" Z6 1 3/4" Z6 1 3/4" Z20
28 29 37
1 3/8" Z21 1 3/8" Z6 1 3/4" Z6 1 3/4" Z201 3/8" Z21
ø1 ø1 ø1
80° EL CV BALL COLLAR 80° EL CV AUTOMATIC BALL COLLAR 80° EL CV TAPER PIN - IMPLEMENT SIDE ONLY
Ø1 24 Ø1 24 Ø1 24 Ø1 24 Ø1 24 Ø1 24 Ø1 24 Ø1 24 Ø1 24
Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28 Ø1 28
Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34 Ø1 34
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
5730E3753
5730G3753
5730L3753
5730E0453
5730G0453
5730L0453
5730E3853
5730G3853
5730L3853
5190E0352
5190G0352
5190L0352
5190E3752
5190G3752
5190L3752
5190G0452
---
5190L0452
---
5190G3852
5190L3852
408000075R
408000075R
---
---
408000075R
408000075R
408000076R
408000076R
408000075R
408000075R
408000076R
408000076R
27LRS/R006 100 SERIES
(B)
(A)
(C)
4 6 8
YOKES FOR 100 SERIES 50° EL CV
1 3/8" Z61 3/8" Z211 3/4" Z61 3/4" Z20
TAPER PIN KITS FOR 80°-50° EL CV
1 3/8" Z21 1 3/4" Z6 1 3/4" Z20 1 3/8" Z21 1 3/4" Z6 1 3/4" Z201 3/8" Z6
43 51ø1 ø1
50° EL CV BALL COLLAR 50° EL CV TAPER PIN - IMPLEMENT SIDE ONLY
ATTENTION - Use pin that fits completely into hub. Discard other pins and nut. Use tapered nut ONLY with pin (C) and yoke with counter-sunk hole.
Ø1 29 Ø1 29 Ø1 29 Ø1 29 Ø1 29
Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33
Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33 Ø1 33
71R4081CEWR7007
71R6081CEWR7007
71R8081CEWR7007
71R4101CEWR7007
71R6101CEWR7007
71R8101CEWR7007
71R4121CEWR7007
71R6121CEWR7007
71R8121CEWR7007
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
28 LRS/R006 100 SERIES
810
081
1010
101
1210
121
80° CV JOINT
100 SERIES DRIVESHAFTS WITH 80° CV JOINTS
COMPLETE DRIVESHAFTS
Codes above are equipped with CE mark (includes CE labels, instructions, and declaration of conformity). For other countries, the "CE" may bereplaced by "UC" (for North America), "JP" (for Japan), or "FX", which will have labels and instructions according to pages 7-8.
L
S1 3/8" Z6
B (mm)SIZEMAXIMUMTORQUE2400 Nm
S1 3/4" Z6
S1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
REF. CODE DESCRIPTION NOTESSIZE
1
2
43-4
5
94
100
109
112
S1 3/8" Z21
94
100
109
112
---
---
---
---
601101701R
601102701R
601104701R
601105704R
601101702R
601102702R
601104702R
601105702R
1
2
3
4
5
6
7
348014000R20
418011201
418021201
418041201
418051201
4210C0001R03
403000001R10
5130C0301
5130C3701
246000132R02
338005000R20
Grease fitting
Housing
Pawl + Spring
Push pin kit
Hub with push pin
Seal plate
Retaining ring
L= 22,8
1 3/8" Z6
1 3/8" Z21
82 x 2.5 DIN 472/1
1
2
43-4
5
1
2
34
5
76
L
---
---
---
---
---
---
---
---
---
---
---
---
LRS/R006 100 SERIES
A
B
B
A
B 21
Section A-A Section B-B
97
S
29
RA1 OVERRUNNING CLUTCH
SPARE PARTS CODE
L
1
2
3 45
76
1
2
3
4
5
6
7
348014000R20
418052203
418062203
418172203
4210E0001R03
408000047R02
408000046R02
5150E0301
5150E3701
5150E0401
5150E3801
246000132R02
246000134R02
338005000R20
Grease fitting
Housing
Pawl + springs kit
Taper pin kit
Hub with taper pin
Seal plate
Two piece seal plate
Retaining ring
L= 42,8
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
1 3/8" Z6
1 3/8" Z21
1 3/4" Z6
1 3/4" Z20
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
82 x 2.5 DIN 472/1
5
6
7
S1 3/8" Z6
B (mm)S
1 3/8" Z21S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
5
6
7
140
147
160
140
147
160
142
149
162
142
149
162
601205601R
601206601R
601217601R
601205602R
601206602R
601217602R
601205603R
601206603R
601217603R
601205604R
601206604R
601217604R
SIZEMAXIMUMTORQUE3800 Nm
REF. CODE DESCRIPTION NOTESSIZE
30 LRS/R006 100 SERIES
A
B
B
A
B
Section A-A Section B-B
97
S
24 S = 1 3/8"29 S = 1 3/4"
RA2 OVERRUNNING CLUTCH
SPARE PARTS CODE
S1 3/8" Z6
B (mm)S
1 3/8" Z21S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
8 191 191 193 193 60170M501R 60170M502R 60170M503R 60170M504R
12
3 4
65
7 87
1
2
3
4
5
6
7
8
4180M7001
354110025
4210G0001R03
408000047R02
408000046R02
5150G0306
5150G3706
5150G0406
5150G3806
246000132R02
246000134R02
338046000R20
359005900R02
Housing
Ball bearing
Pawl + Spring
Taper pin kit
Hub with taper pin
Seal plate
Two-piece seal plate
Retaining ring
Sealing ring
6205 (25 x 52 x 15)
L= 62,8
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
1 3/8" Z6
1 3/8" Z21
1 3/4" Z6
1 3/4" Z20
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
88 x 3 DIN 472/1
SIZEMAXIMUMTORQUE6200 Nm
L
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
A
B
B
A
B 24 S = 1 3/8"
Section A-A Section B-B
97
S
29 S = 1 3/4"
31
RL3 OVERRUNNING CLUTCH (Permanently lubricated)
SPARE PARTS CODE
B 22
Ø12
2
S
S1 3/8" Z6
B (mm)MAXIMUMTORQUE
Nm
S1 3/4" Z6
S1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
SIZES
1 3/8" Z21
608E46501R
608G46501R
608E46502R
608G46502R
4
5
123
134
123
134
---
---
1700
1700
S1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20S
1 3/8" Z21
S1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20S
1 3/8" Z21
Ø12
2
22BS
B 22
S
Ø15
0
608H65501R
608H66501R
608H65502R
608H66502R
608H65503R
608H66503R
608H65504R
608H66504R
6 170
170
170
170
170
170
170
170
1700
3000
7
8
169
170
169
170
169
170
169
170
608L86501R
608M86501R
608L86502R
608M86502R
608L86503R
608M86503R
608L86504R
608M86504R
5000
5000
1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
408000047R02 408000047R02 408000046R02 408000046R02
MAXIMUMTORQUE
Nm
SIZE
MAXIMUMTORQUE
Nm
SIZE
32 LRS/R006 100 SERIES
TAPER PINS
SPARE PARTS CODE
TORSIONALLY RESILIENT JOINTS GE4 - GE6 - GE8
---
---
---
---
---
---
SPARE PARTS CODE
SPARE PARTS CODE
1
2
3
4
5
6
7
348014000R20
422011020
421340001R06
513340302
403000001R10
240000033R02
338005000R20
Grease fitting
Housing
Ratchet + springs
Hub with push pin
Push pin kit
Seal plate
Retaining ring
1 3/8" Z6
82 x 2.5 DIN 472/1
1
REF. CODE DESCRIPTION NOTESSIZE
S1 3/8" Z6
B (mm)TORQUE
Nm S1 3/4" Z6
S1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20
SIZE
1 94 610124001R400 --- ---
S1 3/8" Z21
LRS/R006 100 SERIES
AB
AB
B 21 96
S
Section A-A Section B-B
1
23
45
6
7
SA1 RATCHET TORQUE LIMITERUni-directional
33
SPARE PARTS CODE
--- --- --- ---
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
1
2
114
120
120
---
---
---
610234001R
611234005R
611239001R
650
650
800
1
2
3
4
5
6
7
348014000R20
422012020
422022020
421340001R06
513350302
403000001R10
240000033R02
338005000R20
Grease fitting
Housing
Ratchet + springs
Hub with push pin
Push pin kit
Seal plate
Retaining ring
1 3/8" Z6
82 x 2.5 DIN 472/1
1
2
1
23
45
6
7
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
34 LRS/R006 100 SERIES
AB
B 21 96
S
Section A-A Section B-B
SA2 RATCHET TORQUE LIMITERUni-directional
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm) S1 3/4" Z6
S1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6
S1 3/8" Z21
2
43-4
5
149
149
149
158
158
161
---
---
---
---
---
---
611341501R
611344501R
611348501R
613344501R
613348501R
614348501R
900
1000
1200
1000
1200
1200
1
2
3
4
5
6
7
348014000R20
422023020
422043020
422053020
421340001R06
2270Q0303
240000033R02
338005000R20
435000321R
Grease fitting
Housing
Ratchet + springs
Hub
Seal plate
Retaining ring
Ball collar kit
1 3/8" Z6
82 x 2.5 DIN 472/1
2
43-4
5
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
LRS/R006 100 SERIES
Section A-A Section B-BA B
B 21 96 SA B
2
1
34
56
7
SA3 RATCHET TORQUE LIMITERUni-directional
35
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
43-4
5
6
178
178
181
181
188
188
---
---
---
---
---
---
613452501R
613456501R
614452501R
614456501R
615452501R
615456501R
1400
1600
1400
1600
1400
1600
1
2
3
4
5
6
7
348014000R20
422044020
422054020
422064020
421340001R06
2270R0302
240000033R02
338005000R20
435000321R
Grease fitting
Housing
Ratchet + springs
Hub
Seal plate
Retaining ring
Ball collar kit
1 3/8" Z6
82 x 2.5 DIN 472/1
43-4
5
6
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
36 LRS/R006 100 SERIES
A B
B 21 96A B
96 S
Section A-A Section B-B
2
34
1
56
7
SA4 RATCHET TORQUE LIMITERUni-directional
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
S1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6 1 3/4" Z20S
1 3/8" Z21
1 94 --- 60A1B1903R300
1
2
3
45
6
7
1
2
3
4
5
6
7
348014000R20
422B0S301
421340007R06
513340302
403000001R10
240000294R02
338005000R20
Grease fitting
Housing
Ratchet + springs
Hub with push pin
Push pin kit
Seal plate
Retaining ring
1 3/8" Z6
82 x 2.5 DIN 472/1
1
--- --- --- --- ---
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
LRS/R006 100 SERIES
AB
AB
B 21 96
S
Section A-A Section B-B
37
LN1 RATCHET TORQUE LIMITERSymmetrical
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
1
2
114
114
120
---
---
---
60A2B2603R
60A2B3203R
60A2C3203R
460
600
600
1
2
3
45
67
1
2
3
4
5
6
7
348014000R20
422B0T301
422C0T301
421340007R06
513350302
403000001R10
240000294R02
338005000R20
Grease fitting
Housing
Ratchet + springs
Hub with push pin
Push pin kit
Seal plate
Retaining ring
1 3/8" Z6
82 x 2.5 DIN 472/1
1
2
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
38 LRS/R006 100 SERIES
AB
B 21 96
SA B
Section A-A Section B-B
LN2 RATCHET TORQUE LIMITERSymmetrical
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
2 149
149
---
---
800
900
60B3C3903R
60B3C4103R
1
2
3
4
5
6
7
348014000R20
422C0U301
421340007R06
2270Q0303
240000294R02
338005000R20
435000321R
Grease fitting
Housing
Ratchet + springs
Hub
Seal plate
Retaining ring
Ball collar kit
1 3/8" Z6
82 x 2.5 DIN 472/1
2
---
---
---
---
---
---
---
---
---
---
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
LRS/R006 100 SERIES
A B
B 21 96 SA B
Section A-A Section B-B
2
34
56
7
1
39
LN3 RATCHET TORQUE LIMITERSymmetrical
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
2
43-4
5
169
169
178
178
181
---
---
---
---
---
1000
1200
1000
1200
1200
60B4C4403R
60B4C4803R
60B4E4403R
60B4E4803R
60B4G4803R
1
2
3
4
5
6
7
348014000R20
422C0V301
422E0V301
422G0V301
421340007R06
2270R0302
240000294R02
338005000R20
435000321R
Grease fitting
Housing
Ratchet + springs
Hub
Seal plate
Retaining ring
Ball collar kit
1 3/8" Z6
82 x 2.5 DIN 472/1
2
43-4
5
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
REF. CODE DESCRIPTION NOTESSIZE
TORQUE
Nm
SIZE
40 LRS/R006 100 SERIES
A B
B 21 96A B
96 S
Section A-A Section B-B
2
5
1
34
6
7
LN4 RATCHET TORQUE LIMITERSymmetrical
SPARE PARTS CODE
1
2
3
4
432000002R05
432000047R05
432000053R05
432000124R05
348017000R20
403000001R10
408000048R02
408000052R02
Bolt & Nut
Grease fitting
Push pin kit
Taper pin kit
M6x40 Cl. 8.8
M8x45 Cl. 8.8
M10x50 Cl. 8.8
M12x55 Cl. 8.8
1 3/8" Z6 - Z21
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
REF. CODE DESCRIPTION NOTESSIZE
1
2
43
4
5
6
7
8
37
40
55
60
45
55
45
55
43
67
50
50
55
55
66
62
50
R1mm
68
68
68
68
68
68
68
68
68
80
80
80
80
80
80
80
80
R2mm
80
80
87
87
93
93
93
93
93
106
106
112
112
115
115
121
121
Bmm
650
700
950
1050
1400
1700
1400
1700
2000
2100
2400
2400
2700
2700
3200
3000
3500
1 3/8" Z6
6060B0304R
6060B0302R
6060C0302R
6060C0308R
6060E0303R
6060E0302R
6060E0303R
6060E0302R
6060E0309R
6060G0319R
6060G0304R
6060H0306R
6060H0302R
6060L0303R
6060L0305R
6060M0306R
6060M0307R
1 3/8" Z21
6060B3703R
6060B3702R
6060C3702R
6060C3704R
6060E3704R
6060E3702R
6060E3704R
6060E3702R
6060E3711R
6060G3710R
6060G3704R
6060H3707R
6060H3702R
6060L3703R
6060L3704R
6060M3705R
6060M3703R
1 3/4" Z6
---
---
---
---
---
---
---
---
---
6060G0408R
6060G0404R
6060H0404R
6060H0402R
6060L0404R
6060L0407R
6060M0405R
6060M0407R
1 3/4" Z20
---
---
---
---
---
---
---
---
---
6060G3803R
6060G3804R
6060H3807R
6060H3802R
6060L3807R
6060L3808R
6060M3811R
6060M3809R
TORQUE
Nm
SIZE
M6x40 Cl. 8.8
M6x40 Cl. 8.8
M6x40 Cl. 8.8
M8x45 Cl. 8.8
M8x45 Cl. 8.8
M8x45 Cl. 8.8
M8x45 Cl. 8.8
M8x45 Cl. 8.8
M10x50 Cl. 8.8
M8x45 Cl 8.8
M10x50 Cl. 8.8
M10x50 Cl. 8.8
M10x50 Cl. 8.8
M10x50 Cl. 8.8
M10x50 Cl. 8.8
M10x50 Cl. 8.8
M12x55 Cl. 8.8
LRS/R006 100 SERIES
B 22
R1 R
2 S
Push pin for sizes1, 2, 43, and 4
Taper pin for sizes5, 6, 7, and 8
S
1
1
2
3
1
2
1
4
41
LB SHEAR BOLT TORQUE LIMITER
SPARE PARTS CODE
12 3
67
89
1011
12
4
5
*Torque setting for 1000 min-1
4
5
6
172
172
172
177
177
177
177
184
172
172
172
177
177
177
177
184
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
6WE148003R
6WE154003R
6WE157003R
6WG154003R
6WG157003R
6WG159003R
6WG161003R
6WH161003R
6WE148037R
6WE154037R
6WE157037R
6WG154037R
6WG157037R
6WG159037R
6WG161037R
6WH161037R
*1200
1500
1700
*1500
1700
1900
2100
*2100
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
11
12
4310E1151
4310G1151
431061151
240000205R02
421154801R
421155401R
421155701R
421155901R
421156101R
258000100R05
250000101R05
408000047R02
515150301
515153701
240000201R02
355006080R02
358000006R02
240000202R02
338000138R20
Housing
Bushing
Spring kit
Sleeve
Cam
Taper pin
Hub with taper pin
Bushing
Sealing ring
O-ring
Cover ring
Retaining ring
1200 Nm
1500 Nm
1700 Nm
1900 Nm
2100 Nm
1 3/8" Z6 - Z21
1 3/8" Z6
1 3/8" Z21
80 x 100 x 10 mm
139 x 2.6 mm
138 x 4 DIN 472/1
4
5
6
REF. CODE DESCRIPTION NOTESSIZE
42 LRS/R006 100 SERIES
B
Ø15
1
S29
LR23 AUTOMATIC TORQUE LIMITER
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
12 3
67
89
1011
12
4
5
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
6
7
8
184
184
184
184
192
192
184
184
184
184
192
192
184
184
184
184
192
192
184
184
184
184
192
192
2600
2900
*2500
3000
*2500
3000
6WH266003R
6WH269003R
6WL265003R
6WL270003R
6WM265003R
6WM270003R
6WH266037R
6WH269037R
6WL265037R
6WL270037R
6WM265037R
6WM270037R
6WH266004R
6WH269004R
6WL265004R
6WL270004R
6WM265004R
6WM270004R
6WH266038R
6WH269038R
6WL265038R
6WL270038R
6WM265038R
6WM270038R
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
11
12
431062152
4310L2152
431082152
240000205R02
421166502R
421166601R
421166902R
421167001R
258000100R05
250000108R05
408000047R02
408000052R02
515160301
515163701
515160401
515163801
240000201R02
355006080R02
358000006R02
240000202R02
338000138R20
Housing
Bushing
Spring kit
Sleeve
Cam
Taper pin
Hub with taper pin
Bushing
Sealing ring
O-ring
Cover ring
Retaining ring
2500 Nm
2600 Nm
2900 Nm
3000 Nm
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
1 3/8" Z6
1 3/8" Z21
1 3/4" Z6
1 3/4" Z20
80 x 100 x 10 mm
139 x 2.6 mm
138 x 4 DIN 472/1
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B 29S
Ø15
1
43
LR24 AUTOMATIC TORQUE LIMITER
SPARE PARTS CODE
12
3
4
5
67
89
1011
12
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
6WM481003R 6WM481037R 6WM481004R 6WM481038R8 192 192 192 1923500
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
11
12
431084151
240000711R02
421188101R
258000100R05
250000101R05
408000047R02
408000052R02
515180301
515183701
515180401
515183801
240000712R02
355000105R02
358000007R02
240000710R02
338000162R20
Housing
Bushing
Spring kit
Sleeve
Cam
Taper pin
Hub with taper pin
Bushing
Sealing ring
O-ring
Cover ring
Retaining ring
3500 Nm
1 3/8" Z6 - Z21
1 3/4" Z6 - Z20
1 3/8" Z6
1 3/8" Z21
1 3/4" Z6
1 3/4" Z20
105 x 125 x 10 mm
64.7 x 2.6 mm
162 x 4 DIN 472/1
8
REF. CODE DESCRIPTION NOTESSIZE
44 LRS/R006 100 SERIES
B 29
S
Ø17
6
LR35 AUTOMATIC TORQUE LIMITER
SPARE PARTS CODE
1
2
34 5
6
4
7
81
t
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
1
2
43
4
92
92
100
100
101
101
101
92
92
100
100
101
101
101
---
---
---
---
---
---
---
---
---
---
---
---
---
---
661B24103R
661B28103R
661C28103R
661C32103R
661E32103R
661E39103R
661E39103R
661B24137R
661B28137R
661C28137R
661C32137R
661E32137R
661E39137R
661E39137R
*400
500
*500
600
*600
800
800
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
432000003R08
2530B8503
2530C8503
2530E8503
258005320R02
247006151R08
403000001R10
513850307
513853707
2481A0001
367005850
Bolt and nut
Flange yoke
Bushing
Friction disc
Push pin kit
Hub with push pin
Inner plate
Belleville spring
M8 x 50 mm
D = 124 ; d = 67 mm
1 3/8” Z6 - Z21
1 3/8” Z6
1 3/8” Z21
Sp. = 4 mm
t = 3.75 mm
1
2
43-4
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
Ø15
5
B 29
S
45
FV22 FRICTION TORQUE LIMITERAdjustable torque setting
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
*Torque setting for 1000 min-1
21
1
34
4
56
78
t
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
4
5
113
113
117
117
117
113
113
117
117
117
---
---
---
---
---
661E41203R
661E44203R
661G41203R
661G44203R
661G46203R
661E41237R
661E44237R
661G41237R
661G44237R
661G46237R
---
---
---
---
---
*900
1000
900
1000
*1100
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
432000054R08
253048602
253058901
258005320R02
247006251R08
515860305
515863705
408000047R02
248860007
367008860
Bolt and nut
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Belleville spring
M10 x 55 mm
D = 141 ; d = 77 mm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
Sp. = 8 mm
t = 3.75 mm
4
5
REF. CODE DESCRIPTION NOTESSIZE
46 LRS/R006 100 SERIES
B 29
Ø18
0
S
FV32 FRICTION TORQUE LIMITERAdjustable torque setting
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
21
1
34
4
56
78
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
5
6
7
117
125
125
125
131
131
131
131
117
125
125
125
131
131
131
131
122
130
130
130
136
136
136
136
122
130
130
130
136
136
136
136
661G48403R
661H48403R
661H51403R
661H53403R
661L51403R
661L53403R
661L56403R
661L58403R
661G48437R
661H48437R
661H51437R
661H53437R
661L51437R
661L53437R
661L56437R
661L58437R
661G48404R
661H48404R
661H51404R
661H53404R
661L51404R
661L53404R
661L56404R
661L58404R
661G48438R
661H48438R
661H51438R
661H53438R
661L51438R
661L53438R
661L56438R
661L58438R
1200
*1200
1350
1450
1350
*1450
1600
1800
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
432000008R08
253058701
253069001
253078702
258005320R02
247006351R08
515870305
515873705
515870405
515873805
408000047R02
408000046R02
248870007
367009870
Bolt and nut
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Belleville spring
M10 x 60 mm
D = 162 ; d = 85 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
t = 4.25 mm
5
6
7
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B
Ø20
2
S
29
47
FV42 FRICTION TORQUE LIMITERAdjustable torque setting
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
5
6
7
8
133
140
140
140
146
146
146
146
148
148
133
140
140
140
146
146
146
146
148
148
138
145
145
145
151
151
151
151
153
153
138
145
145
145
151
151
151
151
153
153
661G48303R
661H48303R
661H51303R
661H53303R
661L51303R
661L53303R
661L56303R
661L58303R
661M58303R
661M60303R
661G48337R
661H48337R
661H51337R
661H53337R
661L51337R
661L53337R
661L56337R
661L58337R
661M58337R
661M60337R
661G48304R
661H48304R
661H51304R
661H53304R
661L51304R
661L53304R
661L56304R
661L58304R
661M58304R
661M60304R
661G48338R
661H48338R
661H51338R
661H53338R
661L51338R
661L53338R
661L56338R
661L58338R
661M58338R
661M60338R
1200
*1200
1350
1450
1350
*1450
1600
1800
*1800
2000
TORQUE
Nm
SIZE
48 LRS/R006 100 SERIES
B
Ø18
0
S
29
FV34 FRICTION TORQUE LIMITERAdjustable torque setting
SPARE PARTS CODE
12
34
54
4
4
6
78
910
1
t
1
2
3
4
5
6
7
8
9
10
432000114R08
253058901
253068903
253078601
253088903
258005320R02
247006251R08
248727702
248860001
515890305
515893705
515890405
515893805
408000047R02
408000049R02
248860007
367008860
Bolt and nut
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Inner plate
Belleville spring
M10 x 75 mm
D = 141 ; d = 77 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
t = 3.75 mm
5
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES 49
*Torque setting for 1000 min-1
12
34
54
4
4
6
78
910
1
t
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
661L58503R
661M58503R
661M60503R
661M62503R
661L58537R
661M58537R
661M60537R
661M62537R
661L58538R
661M58538R
661M60538R
661M62538R
661L58504R
661M58504R
661M60504R
661M62504R
7
8
147
149
149
149
147
149
149
149
152
154
154
154
152
154
154
154
1800
*1800
2000
2200
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
432000114R08
253078702
253089001
258005320R02
247006351R08
248737702
248870011
515900305
515903705
515900405
515903805
408000047R02
408000046R02
248870007
367009870
Bolt and nut
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Inner plate
Belleville spring
M10 x 75 mm
D = 162 ; d = 85 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
t = 4.25 mm
7
8
REF. CODE DESCRIPTION NOTESSIZE
50 LRS/R006 100 SERIES
B
Ø20
2
S
29
FV44 FRICTION TORQUE LIMITERAdjustable torque setting
SPARE PARTS CODE
*Torque setting for 1000 min-1
1
2
3
4
5
6
7
8
9
432000031R08
351015001R08
2530B1A05
2530C1A05
2530E1A05
258005320R02
247006151R08
513850307
513853707
403000001R10
2481A0007
2481A0006
Bolt and nut
Coil spring
Flange yoke
Bushing
Friction disc
Hub with push pin
Push pin
Inner plate
Pressure plate
M8 x 75 mm
f = 6 mm
D = 124 ; d = 67 mm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
Sp. = 4 mm
1
2
43-4
92
92
100
100
101
101
101
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
1
2
43
4
92
92
100
100
101
101
101
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
*400
500
*500
600
*600
800
800
635B24103R
635B28103R
635C28103R
635C32103R
635E32103R
635E39103R
635E39103R
635B24137R
635B28137R
635C28137R
635C32137R
635E32137R
635E39137R
635E39137R
TORQUE
Nm
SIZE
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B 29
Ø15
9
S
1 23
45
76
58
91
51
FFV22 FRICTION TORQUE LIMITER (COIL SPRING)Adjustable torque setting
SPARE PARTS CODE
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
4
5
113
113
113
117
117
113
113
113
117
117
*900
1000
900
1000
*1100
635E41203R
635E44203R
635G41203R
635G44203R
635G46203R
635E41237R
635E44237R
635G41237R
635G44237R
635G46237R
---
---
---
---
---
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
432000006R08
351022370R08
2530E1C05
2530G1C05
258005320R02
247006251R08
515860305
515863705
408000047R02
2481C0007
248220007
Bolt and nut
Coil spring
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Pressure plate
M10 x 85 mm
f = 6 mm
D = 141 ; d = 77 mm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
Sp. = 4 mm
4
5
REF. CODE DESCRIPTION NOTESSIZE
52 LRS/R006 100 SERIES
B
Ø18
0
S
29
1 23
45
76
58
91
FFV32 FRICTION TORQUE LIMITER (COIL SPRING)Adjustable torque setting
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
5
6
7
117
125
125
125
131
131
131
131
117
125
125
125
131
131
131
131
122
130
130
130
136
136
136
136
122
130
130
130
136
136
136
136
1200
*1200
1350
1450
1350
*1450
1600
1800
635G48403R
635H48403R
635H51403R
635H53403R
635L51403R
635L53403R
635L56403R
635L58403R
635G48437R
635H48437R
635H51437R
635H53437R
635L51437R
635L53437R
635L56437R
635L58437R
635G48404R
635H48404R
635H51404R
635H53404R
635L51404R
635L53404R
635L56404R
635L58404R
635G48438R
635H48438R
635H51438R
635H53438R
635L51438R
635L53438R
635L56438R
635L58438R
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
432000006R08
351013370R08
2530G1E05
2530H1E05
2530L1E05
258005320R02
247006351R08
515870305
515873705
515870405
515873805
408000047R02
408000046R02
2481E0007
248230006
Bolt and nut
Coil spring
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Pressure plate
M10 x 85 mm
f = 7 mm
D = 162 ; d = 85 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 4 mm
5
6
7
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B
Ø20
2
S
29
1 23 4
5
76
58
91
53
FFV42 FRICTION TORQUE LIMITER (COIL SPRING)Adjustable torque setting
SPARE PARTS CODE
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
5
6
7
8
133
140
140
140
146
146
146
146
148
148
133
140
140
140
146
146
146
146
148
148
138
145
145
145
151
151
151
151
153
153
138
145
145
145
151
151
151
151
153
153
1200
*1200
1350
1450
1350
*1450
1600
1800
*1800
2000
635G48303R
635H48303R
635H51303R
635H53303R
635L51303R
635L53303R
635L56303R
635L58303R
635M58303R
635M60303R
635G48337R
635H48337R
635H51337R
635H53337R
635L51337R
635L53337R
635L56337R
635L58337R
635M58337R
635M60337R
635G48304R
635H48304R
635H51304R
635H53304R
635L51304R
635L53304R
635L56304R
635L58304R
635M58304R
635M60304R
635G48338R
635H48338R
635H51338R
635H53338R
635L51338R
635L53338R
635L56338R
635L58338R
635M58338R
635M60338R
TORQUE
Nm
SIZE
54 LRS/R006 100 SERIES
B
Ø18
0
S
29
FFV34 FRICTION TORQUE LIMITER (COIL SPRING)Adjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
432000007R08
351022370R08
2530G1C05
2530H1C05
2530L1C05
2530M1C05
258005320R02
247006251R08
248727702
2481C0007
515890305
515893705
515890405
515893805
408000047R02
408000049R02
248220007
Bolt and nut
Coil spring
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Pressure plate
M10 x 100 mm
f = 6 mm
D = 141 ; d = 77 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
5
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
34
56
57
5
98
57
101
1 2
55
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
7
8
147
149
149
149
147
149
149
149
152
154
154
154
152
154
154
154
1800
*1800
2000
2200
635L58503R
635M58503R
635M60503R
635M62503R
635L58537R
635M58537R
635M60537R
635M62537R
635L58538R
635M58538R
635M60538R
635M62538R
635L58504R
635M58504R
635M60504R
635M62504R
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
432000122R08
351013370R08
2530L1E05
2530M1E05
258005320R02
247006351R08
248737702
2481E0007
515900305
515903705
515900405
515903805
408000047R02
408000046R02
248230006
Bolt and nut
Coil spring
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Pressure plate
M10 x 105 mm
f = 7 mm
D = 162 ; d = 85 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
7
8
REF. CODE DESCRIPTION NOTESSIZE
56 LRS/R006 100 SERIES
B
Ø20
2
S
29
3 45
65
75
98
57
101
1 2
FFV44 FRICTION TORQUE LIMITER (COIL SPRING)Adjustable torque setting
SPARE PARTS CODE
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
1
2
43
4
92
92
100
100
101
101
101
92
92
100
100
101
101
101
---
---
---
---
---
---
---
663B24103R
663B28103R
663C28103R
663C32103R
663E32103R
663E39103R
663E39103R
663B24137R
663B28137R
663C28137R
663C32137R
663E32137R
663E39137R
663E39137R
*400
500
*500
600
*600
800
800
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
432000047R08
2530B8503
2530C8503
2530E8503
258005320R02
247006151R08
403000001R10
513850307
513853707
2481A0002
240001059
367FT220A
367FT220C
367FT220D
367FT220E
Bolt and nut
Flange yoke
Bushing
Friction disc
Push pin
Hub with push pin
Inner plate
Spacer band
Belleville spring
M8 x 45 mm
D = 124 ; d = 67 mm
1 3/8” Z6 - Z21
1 3/8” Z6
1 3/8” Z21
Sp. = 4 mm
400 Nm
500 Nm
600 Nm
800 Nm
1
2
43-4
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
S
B 29
Ø15
5
12
34
4
56
78
91
FT22 FRICTION TORQUE LIMITERNon-adjustable torque setting
57
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
4
5
113
113
117
117
117
113
113
117
117
117
---
---
---
---
---
663E41203R
663E44203R
663G41203R
663G44203R
663G46203R
663E41237R
663E44237R
663G41237R
663G44237R
663G46237R
*900
1000
900
1000
*1100
12
34
56 4
78
91
*Torque setting for 1000 min-1
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
432000054R08
253048602
253058901
258005320R02
247006251R08
515860305
515863705
408000047R02
248860005
240000213
367FT320A
367FT320C
367FT320D
Bolt and nut
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Spacer band
Belleville spring
M10 x 55 mm
D = 141 ; d = 77 mm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
Sp. = 8 mm
900 Nm
1000 Nm
1100 Nm
4
5
REF. CODE DESCRIPTION NOTESSIZE
58 LRS/R006 100 SERIES
B
Ø18
0
S
29
FT32 FRICTION TORQUE LIMITERNon-adjustable torque setting
SPARE PARTS CODE
12
34
56 4
78
91
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
5
6
7
117
125
125
131
131
117
125
125
131
131
122
130
130
136
136
122
130
130
136
136
1200
*1200
1450
*1450
1800
663G48403R
663H48403R
663H53403R
663L53403R
663L58403R
663G48437R
663H48437R
663H53437R
663L53437R
663L58437R
663G48404R
663H48404R
663H53404R
663L53404R
663L58404R
663G48438R
663H48438R
663H53438R
663L53438R
663L58438R
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
432000054R08
253058701
253069001
253078702
258005320R02
247006351R08
515870305
515873705
515870405
515873805
408000047R02
408000046R02
248870005
240000214
367FT420A
367FT420C
367FT420D
Bolt and nut
Flange yoke
Bushing
Friction disc
Hub with taper pin
Taper pin
Inner plate
Spacer band
Belleville spring
M10 x 55 mm
D = 162 ; d = 85 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
1200 Nm
1450 Nm
1800 Nm
5
6
7
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B
Ø20
2
S
29
FT42 FRICTION TORQUE LIMITERNon-adjustable torque setting
59
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
5
6
7
133
140
140
146
146
133
140
140
146
146
138
145
145
151
151
138
145
145
151
151
1200
*1200
1450
*1450
1800
663G48303R
663H48303R
663H53303R
663L53303R
663L58303R
663G48337R
663H48337R
663H53337R
663L53337R
663L58337R
663G48304R
663H48304R
663H53304R
663L53304R
663L58304R
663G48338R
663H48338R
663H53338R
663L53338R
663L58338R
12
34
56
78
4
4
49
1011
1
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
11
432000045R08
253058901
253068903
253078601
258005320R02
247006251R08
248727702
248860001
515890305
515893705
515890405
515893805
408000047R02
408000049R02
248860005
240000218
367FT340A
367FT340C
367FT340D
Bolt and nut
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Inner plate
Spacer band
Belleville spring
M10 x 65 mm
D = 141 ; d = 77 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
1200 Nm
1450 Nm
1800 Nm
5
6
7
REF. CODE DESCRIPTION NOTESSIZE
60 LRS/R006 100 SERIES
B
Ø18
0
S
29
FT34 FRICTION TORQUE LIMITERNon-adjustable torque setting
SPARE PARTS CODE
12
34
5
6
78
4
4
49
1011
1
*Torque setting for 1000 min-1
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
663L58503R
663M58503R
663M62503R
663L58537R
663M58537R
663M62537R
663L58538R
663M58538R
663M62538R
663L58504R
663M58504R
663M62504R
7
8
147
149
149
147
149
149
152
154
154
152
154
154
1800
*1800
2200
TORQUE
Nm
SIZE
1
2
3
4
5
6
7
8
9
10
11
432000100R08
253078702
253089001
258005320R02
247006351R08
248737702
248870011
515900305
515903705
515900405
515903805
408000047R02
408000046R02
248870005
240000219
367FT440A
367FT440C
367FT440D
367FT440E
Bolt and nut
Flange yoke
Bushing
Friction disc
Drive plate
Inner plate
Hub with taper pin
Taper pin
Inner plate
Spacer band
Belleville spring
M10 x 55 mm
D = 162 ; d = 85 mm
Sp. = 4 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
Sp. = 8 mm
1800 Nm
2200 Nm
2400 Nm
2600 Nm
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
B
Ø20
2
S
29
FT44 FRICTION TORQUE LIMITERNon-adjustable torque setting
61
SPARE PARTS CODE
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
665G48103R
665H48103R
665H51103R
665H53103R
665L51103R
665L53103R
665L56103R
665L58103R
665M58103R
665M60103R
665G48137R
665H48137R
665H51137R
665H53137R
665L51137R
665L53137R
665L56137R
665L58137R
665M58137R
665M60137R
5
6
7
8
158
166
166
166
172
172
172
172
174
174
158
166
166
166
172
172
172
172
174
174
---
---
---
---
---
---
---
---
---
---
1200
*1200
1350
1450
1350
*1450
1600
1800
*1800
2000
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
TORQUE
Nm
SIZE
62 LRS/R006 100 SERIES
B
Ø18
0
S
24
FNV34 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHAdjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
432000114R08
2530G1L01
2530H1L01
2530L1L01
2530M1L01
247000054R08
2481L0003
2481L0001
240000737
303008001R03
240000736
4271L0101
348017000R20
2481L0005
367008860
339002060R20
4211L0001R06
5151L0301
5151L3701
408000047R02
Bolt and nut
Flange yoke
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Inner plate
Belleville spring
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M 10 x 75 mm
D = 140 ; d = 85 mm
Sp. = 4 mm
M8 x 16
Sp. = 8 mm
1200 Nm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
5
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
34
35
376
9
111
16
12
810 3
1213
1514
63
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
7
8
172
174
174
174
172
174
174
174
172
174
174
174
172
174
174
174
665L58203R
665M58203R
665M60203R
665M62203R
1800
*1800
2000
2200
665L58237R
665M58237R
665M60237R
665M62237R
665L58238R
665M58238R
665M60238R
665M62238R
665L58204R
665M58204R
665M60204R
665M62204R
TORQUE
Nm
SIZE
64 LRS/R006 100 SERIES
B
Ø20
2
S
29
FNV44 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHAdjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
432000114R08
2530L1M01
2530M1M01
247000061R08
2481M0001
2481M0002
240000735
303008001R03
240000734
4271M0101
348017000R20
2481H0004
367009870
339002068R20
4211L0001R06
5151M0301
5151M3701
5151M0401
5151M3801
408000047R02
408000046R02
Bolt and nut
Flange yoke
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Inner plate
Belleville spring
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M 10 x 75 mm
D = 160 ; d = 97 mm
Sp. = 4 mm
M8 x 16
Sp. = 8 mm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
34
35
376
9
111
16
12
810 3
1213
1514
65
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
667G48103R
667H48103R
667H51103R
667H53103R
667L51103R
667L53103R
667L56103R
667L58103R
667M58103R
667M60103R
667G48137R
667H48137R
667H51137R
667H53137R
667L51137R
667L53137R
667L56137R
667L58137R
667M58137R
667M60137R
5
6
7
8
158
166
166
166
172
172
172
172
174
174
158
166
166
166
172
172
172
172
174
174
---
---
---
---
---
---
---
---
---
---
1200
*1200
1350
1450
1350
*1450
1600
1800
*1800
2000
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
TORQUE
Nm
SIZE
66 LRS/R006 100 SERIES
B
Ø18
0
S
24
FFNV34 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHAdjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
432000007R08
351022370R08
2530G1L05
2530H1L05
2530L1L05
2530M1L05
247000054R08
2481L0003
2481L0007
240000737
303008001R03
240000736
4271L0101
348017000R20
248220007
339002060R20
4211L0001R06
5151L0301
5151L3701
408000047R02
Bolt and nut
Coil spring
Flange yoke
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Pressure plate
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M10 x 100 mm
f = 6 mm
D = 140 ; d = 85 mm
Sp. = 4 mm
M8 x 16
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
5
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
45
46
487
10
1
13
911 4
12
13
2
161514
6
67
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
667L58203R
667M58203R
667M60203R
667M62203R
667L58237R
667M58237R
667M60237R
667M62237R
667L58238R
667M58238R
667M60238R
667M62238R
667L58204R
667M58204R
667M60204R
667M62204R
7
8
172
174
174
174
172
174
174
174
172
174
174
174
172
174
174
174
1800
*1800
2000
2200
TORQUE
Nm
SIZE
68 LRS/R006 100 SERIES
B
Ø20
2
S
29
FFNV44 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHAdjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
432000122R08
351013370R08
2530L1M05
2530M1M05
247000061R08
2481M0001
2481M0007
240000735
303008001R03
240000734
4271M0101
348017000R20
248230006
339002068R20
4211L0001R06
5151M0301
5151M3701
5151M0401
5151M3801
408000047R02
408000046R02
Bolt and nut
Coil spring
Flange yoke
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Pressure plate
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M10 x 105 mm
f = 7 mm
D = 160 ; d = 97 mm
Sp. = 4 mm
M8 x 16
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
6
45
46
487
10
16
13
911 4
121
1514
2
13
69
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
5
6
7
8
158
166
166
172
172
174
158
166
166
172
172
174
---
---
---
---
---
---
1200
*1200
1450
*1450
1800
*1800
658G48103R
658H48103R
658H53103R
658L53103R
658L58103R
658M58103R
658G48137R
658H48137R
658H53137R
658L53137R
658L58137R
658M58137R
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
TORQUE
Nm
SIZE
70 LRS/R006 100 SERIES
B
Ø18
0
S
24
FNT34 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHNon-adjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
432000100R08
2530G1L01
2530H1L01
2530L1L01
2530M1L01
240000218
247000054R08
2481L0003
2481L0001
2400000737
303008001R03
240000736
4271L0101
348017000R20
2481L0002
367FT340A
367FT340C
367FT340D
339002060R20
4211L0001R06
5151L0301
5151L3701
408000047R02
Bolt and nut
Flange yoke
Spacer band
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Inner plate
Belleville spring
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M10 x 70 mm
D = 140 ; d = 85 mm
Sp. = 4 mm
M8 x 16
Sp. = 8 mm
1200 Nm
1450 Nm
1800 Nm
1 3/8” Z6
1 3/8” Z21
1 3/8” Z6 - Z21
5
6
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
34
54
64
8710
121
17
12
911 4
1314
1615
71
1 3/4" Z20S
1 3/8" Z6
B (mm)S
1 3/4" Z6S
1 3/4" Z20 1 3/8" Z6 1 3/8" Z21 1 3/4" Z6S
1 3/8" Z21
*Torque setting for 1000 min-1
7
8
172
174
174
172
174
174
172
174
174
172
174
174
1800
*1800
2200
658L58303R
658M58303R
658M62303R
658L58337R
658M58337R
658M62337R
658L58338R
658M58338R
658M62338R
658L58304R
658M58304R
658M62304R
TORQUE
Nm
SIZE
72 LRS/R006 100 SERIES
B
Ø20
2
S
29
FNT44 FRICTION TORQUE LIMITER + OVERRUNNING CLUTCHNon-adjustable torque setting
SPARE PARTS CODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
432000100R08
2530L1M01
2530M1M01
240000219
247000061R08
2481M0001
2481M0002
240000735
303008001R03
240000734
4271M0101
348017000R20
2481H0003
367FT440A
367FT440C
367FT440D
367FT440E
339002068R20
4211L0001R06
5151M0301
5151M3701
5151M0401
5151M3801
408000047R02
408000046R02
Bolt and nut
Flange yoke
Spacer band
Friction disc
Drive plate
Inner plate
Seal plate
Screw
Cap - overrunning clutch
Flanged housing
Grease fitting
Inner plate
Belleville spring
Retaining ring
Pawl + spring kit
Hub with taper pin
Taper pin
M 10 x 70 mm
D = 160 ; d = 97 mm
Sp. = 4 mm
M8 x 16
Sp. = 8 mm
1800 Nm
2200 Nm
2400 Nm
2600 Nm
1 3/8” Z6
1 3/8” Z21
1 3/4” Z6
1 3/4” Z20
1 3/8” Z6 - Z21
1 3/4” Z6 - Z20
7
8
REF. CODE DESCRIPTION NOTESSIZE
LRS/R006 100 SERIES
34
54
64
8710
121
17
12
911 4
1314
1615
73
74 LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
OVERRUNNING CLUTCHES AND TORQUE LIMITERS
RA1
RA2SA
SA
OLD STYLE
REPLACEMENT PAWLS AND RATCHETS RA - SA
Outer spring Ø 2.4 mm
Outer spring Ø 2.2mm
NEW STYLE
RA3
L = 23
L = 43
L = 63
*Each piece consists of one ratchet,one outer spring, and one inner spring.
** Some torque settings do not require the fullnumber of ratchets or inner springs. Replace withthe original quantity of ratchets and diameter ofsprings.
RA OVERRUNNING CLUTCH SA RATCHET TORQUE LIMITER
T= Torque setting Nm
421011001R03 421011101R03 421340001R06
421022001R03 421022101R03 421341001R06
421463101R03
1 3/8" Z6RA1 SA1 SA2 SA3 SA4
610124001R 610234001R
611124001R 611239001R 611341001R
612124001R 612239001R 612348001R 612450001R
613239002R 613348001R 613456001R
614239001R 614348001R 614456001R
615348002R 615456001R
1 3/8" Z6RA2
1 3/8" Z6RA3
T = 400
T = 400
T = 400
T = 650
T = 800
T = 800
T = 800
T = 800
T = 900
T = 1600
T = 1300
T = 1600
T = 1600
T = 1200
T = 1200
T = 1200
T = 1200
1 3/8" Z6 1 3/8" Z6 1 3/8" Z6 1 3/8" Z6
T = 800 T = 1300T = 1200
613239002R 613348001R 613450003R
SN RATCHET TORQUE LIMITER
601101001R
601102001R
601103001R
601105001R
601106001R 601205201R
601206201R
601217201R
601308201R
601319201R
601310201R
601104001R
T = 300
6MB119203R
T = 300
T = 600
T = 600
T = 600
T = 900
T = 900
T = 900
T = 900
T = 1200
T = 1200
T = 1200
T = 1200
6MC119203R
6MB232203R
6MC232203R
6MD232203R
6MC341203R
6MD341203R
6ME341203R
6MG341203R
6MD448203R
6ME448203R
6MG448203R
6MH448203R
SN1 SN2 SN3 SN41 3/8" Z6 1 3/8" Z6 1 3/8" Z6 1 3/8" Z6
T = 600 T = 700 T = 960
6ME232203R 6MD336203R 6MD443203R
RA1 RA2 - 3
L L
Type
SN1
SN2
SN3
SN4
Torque Setting Nm
TORQUE SETTINGS FOR SN TORQUE LIMITERSSize
230
260
300
360
460
500
600
700
800
900
960
1050
1200
1
1•2
1•2
1•2•43
1•2•43
1•2•43
1•2•43
2•43
2•43•4
2•43•4•5
43
43•4•5•6
43•4•5•6
OLDSTYLE
NEWSTYLE
OUTER SPRING
INNER SPRING Ø 1,4 mm
T=Taratura
75LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
M8 x 50 SB 3 - SB 43 - SB 4
M10 x 60 SB 6
M12 x 65 SB 7/8/9
M14 x 75 SB 10
M6 x 40 SB1/2
M10 x 50 SB 5
*
1 3/8" Z6 1 3/8" Z21
BOLT & NUTS FOR SB (cl. 8.8 )
432000002R05
432000003R05
432000053R05
Ø x L
432000008R05
432000011R05
432000055R05
Ø
L
Code*
Packaged five (5) bolts and nuts per pack
606606002R
T = 650
606101001R
T = 900
606202001R
T = 1300
606303001R
T = 1700
606404001R
T = 2100
606505001R
T = 2500
606606001R
T = 3000
606717004R
T = 3500
606808001R
T = 4000
606919001R
T = 4500
606010001R
T = 2500
1 3/4" Z61 3/8" Z6SB
606808002R
T = 3500
SB SHEAR BOLT
T = 1300
606404023R
T = 3000
606717006R
T = 4000
T = 4500
606919002R
606010002R
LR AUTOMATIC TORQUE LIMITER
LR23 LR241 3/4" Z6 1 3/4" Z201 3/8" Z6 1 3/8" Z21
T = 2100
T = 1700
6WE157003R
6WG161003R
T = 1700
6WE157037R
T = 2100
6WG161037R
6W6265003R
T = 2500
6W6265037R
T = 2500
6W6265004R
T = 2500
6W6265038R
T = 2500
6WL269003R
T = 2900 T = 2900 T = 2900 T = 2900
6WL269037R 6WL269004R 6WL269038R
LRS/R006 100 SERIES
TORQUE LIMITERS
76
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
T = 4000
6W9474004R
T = 4500
6W0480004R
LR35
LR AUTOMATIC TORQUE LIMITER
LR35 LR35 LR35
T = 3500
6W8481003R
T = 3500
6W8481037R
T = 3500
6W8481004R
T = 3500
6W8481038R
T = 4000
6W9474038R
T = 4500
6W0480038R
FF FRICTIONTORQUE LIMITER
Replace linings when they are worn to 1/2 their original thickness (new linings are nominally 3.2 mm thick) or after the clutch has beenoverheated (smoked).
247006251R08FV 32
FF 1 / FF3FF2 / FF4 247000061R08
247000054R08
FF4 247000057R08
140 x 85
160 x 97160 x 100
142 x 77
FRICTION LININGS FOR CLUTCHES FF
FF41 3/8" Z6
639453001R
656457003R
T = 1450
T = 1700
641460003R
T = 2000
657460001R
T = 2000
642460003R
T = 2000
FF11 3/8" Z6
638141001R
639141001R
T = 900
T = 900
T = 750
636137001R
T = 900
637141001R
FF21 3/8" Z6
638248004R
639248001R
656248005R
641248002R
T =1200
T = 1200
T = 1200
T = 1200
FF31 3/8" Z6
656354001R
T = 1500
641354003R
T = 1700
638348001R
T =1200
639353001R
T =1450
I.D.
O.D
.
TYPE O.D. x I.D CODE
T = 750
637137001R
T = 1450
639453002R
642460002R
T = 2000
656457004R
T = 2000
641460004R
T = 2000
657460002R
T = 2000
1 3/4" Z6
T= Torque setting Nm
1 3/4" Z6 1 3/4" Z201 3/8" Z6 1 3/8" Z21
LRS/R006 100 SERIES
FV FRICTION TORQUE LIMITER
FV221 3/8" Z6
FV32 FV34 FV42 FV441 3/8" Z6 1 3/8" Z6 1 3/4" Z6 1 3/8" Z6 1 3/4" Z6
247006251R08FV34
FV42 - FV44 247006351R08
142 x 77
162 x 85
FRICTION LININGS FOR CLUTCHES FV
1 3/8" Z6 1 3/4" Z6
Replace linings when they are worn to 1/2 their original thickness (new linings are nominally 3.2 mm thick) or after the clutch has beenoverheated (smoked).
T = 800
6DE239103R
T = 900
T = 900
T = 750
6D3337003R
T = 900
6DE341003R
6DG341003R
6D6341003R
T = 1200
6DG748003R
T = 1500
6D6754003R
T = 1500
6DL754003R
T = 1500
6D8754003R
T = 1200
6DG748004R
T = 1500
6D6754004R
T = 1500
6DL754004R
T = 1500
6D8754004R
T = 1200
6DG448003R
T = 1200
6D6448003R
T = 1200
6DL448003R
T = 1200
6D8448003R
T = 1200
6DG448004R
T = 1200
6D6448004R
T = 1200
6DL448004R
T = 1200
6D8448004R
T = 1700
6DL857003R
T = 2000
6D8860003R
T = 2000
6D9860003R
T = 2000
6D0860003R
T = 1450
6D6853003R
T = 1700
6DL857004R
T = 2000
6D8860004R
T = 2000
6D9860004R
T = 2000
6D0860004R
T = 1450
6D6853004R
I.D.
O.D
.
TYPE O.D. x I.D CODE
T = 400
6DB224103R
T = 400
6DC232103R
T = 800
6DE239103R
T = 750
6DE341003R
T= Torque setting Nm
247006151R08FV 22 122 x 67
77
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
LRS/R006 100 SERIES
TORQUE LIMITERS
78
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
FT FRICTION TORQUE LIMITER
FT22 FT421 3/8" Z6 1 3/8" Z6 1 3/4" Z6
247006251R08FT32 - FT34 - FN24FT 42 - FT44 - FN44 247006351R08
142 x 77
162 x 85
FRICTION LININGS FOR CLUTCHES FT- FN
1 3/8" Z6 1 3/4" Z6FT32
1 3/8" Z6FT34
Replace linings when they are worn to 1/2 their original thickness (new linings are nominally 3.2 mm thick) or after the clutch has beenoverheated (smoked).
247006151R08FT 22 122 x 67
FT441 3/8" Z6 1 3/4" Z6
T = 400
6LB224103R
T = 600
6LC232103R
T = 600
6LE239103R
T = 800
6L3339003R
T = 1000
6LE344003R
T = 1100
6LG346003R
T = 1200
6LG748003R
T = 1450
6LH753003R
T = 1700
6LL757003R
T = 1800
6LM758003R
T = 1200
6LG748004R
T = 1450
6LH753004R
T = 1700
6LL757004R
T = 1800
6LM758004R
T = 1200
6LG448003R
T = 1450
6LH453003R
T = 1700
6LL457003R
T = 1200
6LG448004R
T = 1450
6LH453004R
T = 1700
6LL457004R
T = 2100
6LM861003R
T = 2400
6L9864003R
T = 2800
6L0868003R
T = 2100
6LM861004R
T = 2400
6L9864004R
T = 2800
6L0868004R
I.D.
O.D
.
TYPE O.D. x I.D CODE
T = 600 T = 800
6LE239103R 6LE339003R
T= Torque setting Nm
1 3/
8" Z
6
LRS/R006 100 SERIES 79
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
FN FRICTION TORQUE LIMITER
RAS FE2
RA OVERRUNNING CLUTCH WITH MALE SHAFT(Not available for sale in North America)
FE2 FRICTION + OVERRUNNING CLUTCH FOR BALERS
RAS1 603100R FE2 650240R
RAS2 603200201R
RAS3 603300201R
1 3/4" Z6FN44
T = 1450
660653104R
T = 1700
660L57104R
T = 2100
660861104R
1 3/8" Z6FN22
T = 1200
659548103R
T = 1450
659653103R
T = 1700
659653103R
T = 1800
659858103R
1 3/8" Z6FN24
1 3/8" Z6
T = 1450
660653103R
T = 1700
660L57103R
T = 2100
660861103R
T= Torque setting Nm
T = 1200
687548703R
T = 1450
687653703R
T = 1700
687757703R
T = 1800
687858703R
80
1700210025002900
N•m H Ø R
LR23 - LR24 AUTOMATIC TORQUE LIMITERS
R
Ø
H A
7
8491103106
2730,230,235
TYPE
LR23LR23LR24LR24
1 3/4” Z201 3/8” Z6 1 3/8” Z21 1 3/4” Z6
151151151151
A A A A
6WE157003R6WE161003R6WE265003R6WE269003R
6WE157037R6WG161037R6W6265037R6WL269037R
--
6W6265004R6WL269004R
--
6W6265038R6WL269038R
1 2 3 6 7 8 9 10 11 12
4
5
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
Ref. Description Qty.LR23 LR24Qty.
1
2
3
4
5
6
7
89
4310E115111111111133
1111111111111
-4310G1151 -
- 431062152
for size 4
- 4310L2152
for size 5for size 6
421155701R -
for size 7
421156101R -for size 5- 421166502Rfor size 6- 421166902R
258000100R05250000101R05 -
- 250000108R04408000047
- 408000052515150301 -515153701
515160301-515163701515160401-515163801-
240000201R02
-
-
101112
for size 4
for size 7
240000205R02 240000205R02
258000100R05
408000047
240000201R02
355006080358000006240000202338000138
355006080358000006240000202338000138
11111111144
1111111111111
139 x 2,6 mm
1-3/8” z6
1-3/8” z21
1-3/4” z61-3/4” z20
1-3/8” z6 - 1-3/8” z21
1-3/4” z6 - 1-3/4” z20
1-3/8” z61-3/8” z21
80 x 100 x 10 mm
138 x 4 DIN 472/1
81
350040004500
N•m H Ø R
Ref. Description LR35
LR35 AUTOMATIC TORQUE LIMITERS
Qty.
1
2
3
45
6
7
89
431084151431094151431104151
240000711R02421188101R421187401R421188001R
258000100R05250000101R05
408000047408000052515180301515183701515180401515183801
240000712R02355000105358000007240000710338000162
for size 8for size 9for size 10
R
Ø
H A
117119
130,5
354141
TYPE
LR35LR35LR35
1 3/4” Z201 3/8” Z6 1 3/8” Z21 1 3/4” Z6
176176176
A A A A
6W8481003R--
6W8481004R6W9474004R6W0480004R
1 2 3 6 7 8 9 10 11 12
4
5
101112
8910
6W8481037R--
6W8481038R6W9474038R6W0480038R
for size 8for size 9
for size 10
11111115511111111111
1-3/8” z6
1-3/8” z211-3/4” z61-3/4” z20
1-3/8” z6 - 1-3/8” z21
1-3/4” z6 - 1-3/4” z20
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
82
N•m H Ø R8084849191103103106117
272727
30,230,230,230,23535
TYPEFV32FV32FV32FV32FV34FV32FV34FV34FV34
1 3/4” Z201 3/8” Z6 1 3/8” Z21 1 3/4” Z6180180180180180180180180180
A A A A
6D3337003R6DE337003R6DE341003R6DG341003R6DG748003R6D6341003R6D6754003R6DL754003R6D8754003R
7507509009001200900150015001500
Ref. Description Qty.FV32 FV34
FV32 - FV34 FRICTION TORQUE LIMITERS
Qty.
1
2
3456
7
8
9
432000054R08for size 3 253038601 -for size 43-4 253048602 -for size 5 253058901for size 6 253068903for size 7 - 253078601for size 8 - 253088903
258005320R02 258005320R02D = 140 mm; d = 77mm 247006251R08
- 248727702
1-3/8” z6- 248860001
1-3/8” z21515860305515863705
515890405515893805
8 mm
-408000047
248860005
-
43
5
4
7
6D3337037R6DE337037R6DE341037R6DG341037R6DG748037R6D6341037R6D6754037R6DL754037R6D8754037R
----
6DG748004R-
6D6754004R6DL754004R6D8754004R
----
6DG748038R-
6D6754038R6DL754038R6D8754038R
ARH
Ø
2 4 4 6 43 5 4 7
1
9 10
1
8
432000045R08
253058901253068903
247006251R08
10
1-3/4” z61-3/4” z201-3/8” z6 - 1-3/8” z21 408000047
3,5 mm4 mm
367009860
1-3/4” z6 - 1-3/4” z20 - 408000049
248860005
367009860367006860 -
515893705
515890305
81111--12--11--1-111
8--1111141111111111-
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
83
N•m H Ø R91103103106106117117119131
30,230,230,2353535354141
TYPEFV42FV42FV44FV42FV44FV42FV44FV44FV44
1 3/4” Z201 3/8” Z6 1 3/8” Z21 1 3/4” Z6202202202202202202202202202
A A A A
6DG448003R6D6448003R6D6853003R6DL448003R6DL857003R6D8448003R6D8860003R6D9860003R6D0860003R
120012001450120017001200200020002000
FV42 - FV44 FRICTION TORQUE LIMITERS
56
7
ARH
Ø
2 4 4 6 43 5 4 7
1
9 10
1
8
910
6DG448037R6D6448037R6D6853037R6DL448037R6DL857037R6D8448037R6D8860037R6D9860037R6D0860037R
6DG448004R6D6448004R6D6853004R6DL448004R6DL857004R6D8448004R6D8860004R6D9860004R6D0860004R
6DG448038R6D6448038R6D6853038R6DL448038R6DL857038R6D8448038R6D8860038R6D9860038R6D0860038R
Ref. Description Qty.FV42 FV44Qty.
1
2
3456
7
8
9
432000054R08for size 5 253058701 -for size 6 253069001 253069001for size 7 253078702for size 8 253089001for size 9 - 253098702for size 10 - 253108702
258005320R02 258005320R02247006351R08
- 248737702
1-3/8” z6- 248870011
1-3/8” z21515870305515873705
515900405515903805
8 mm
515873805408000047
248870005
515870405
432000100R08
247006351R08
10
1-3/4” z61-3/4” z201-3/8” z6 - 1-3/8” z21 408000047
4,25 mm4,5 mm
367009870
1-3/4” z6 - 1-3/4” z20 408000046 408000046248870005
367009870367006860 367006860
515903705
515900305
81111--12--111111111
8-111111411111111111
253078702253089001
D = 162 mm; d = 85 mm
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
84
750
N•m H Ø A R FF1 R FF2
79,5 1 3/8” Z6 180 636137001R 200 -27900 84 1 3/8” Z6 180 637141001R 200 -27900 1 3/8” Z6 180 638141001R 200 -
30,21200
911 3/8” Z6 180 - 200 638248004R
900 1 3/8” Z6 180 639141001R 200 -1200 103 1 3/8” Z6 180 - 20030,21200 1 3/4” Z6 180 200
1200 1171 3/8” Z6 180 2001 3/4” Z6 180 200
35
---
639248001R639248008R641248002R641248003R
Ref. Description Qty.FF1 FF2
FF1 - FF2 FRICTION TORQUE LIMITERS
Qty.
1
2
3
4
5
6
789
Ø 5 mm 351016370R088 351016370R088Ø 6 mm 351022370R088 351022370R088Ø 7 mm 351013370R088 351013370R088
for size 3 2530320011 --for size 4 2530420011 --for size 5 2530520011 2530521011for size 6 2530622031 2530623021for size 7 -- 2531723021for size 8 -- 2530823021
258005320R021 258005320R021140 mm 247000054R082 --160 mm -- 247000061R0821-3/8” z6 5152003111 51521031111-3/8” z21 5152037111 51521371111-3/4” z6 -- 51521041111-3/4” z20 -- 1
4080000601-3/8” z6 - 1-3/8” z21 4080000601408000061
11-3/4” z6 - 1-3/4” z20 -
248230002R021
4 mm 248220008R021248230006R02
1248220007R021
432000006R81
432000006R88 8
-
515213811
21 3 4 4 7 8 9
65
H R A
Ø
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
85
1200
N•m H Ø A R FF3 R FF4
91 1 3/8” Z6 180 638348001R 200 -30,2
14501 3/8” Z6 180 639353001R 200 639453001R
30,21031 3/4” Z6 180 639353002R 200 639453002R1 3/8” Z6 180 641354003R 200 -
351500 1171 3/4” Z6 180 641354002R 200 -1 3/8” Z6 180 - 200 641460003R
352000 1171 3/4” Z6 180 - 200 641460004R1 3/8” Z6 180 - 200 657460001R
2000 1191 3/4” Z6 180 - 200 657460002R
41
2000 130,51 3/4” Z6 180 - 200 642460002R
411 3/8” Z6 180 - 200 642460003R
FF3 FF4
FF3 - FF4 FRICTION TORQUE LIMITERS
Ref. Description Qty.Qty.
1
2
3
4
5
8
9
Ø 5 mm 351016370R088 351016370R088Ø 6 mm 351022370R088 351022370R088Ø 7 mm 351013370R088 351013370R088
for size 5 2530520011 --for size 6 2530622031 253062302-for size 7 2531722011 2531723021for size 8 2530822011 2530823021for size 9 -- 2531923011for size 10 -- 2531023011
258005320R021 258005320R021140 mm 247000054R082 --160 mm -- 247000061R082
248220001R021 27523000414 mm 248220008R022 248230002R0221-3/8”z6 5152203111 51523031111-3/8”z21 5152237111 51523371111-3/4”z6 5152204111 51523041111-3/4”z20 5152238111 51523381111-3/8” z6 - 1-3/8” z21 4080000601 40800006011-3/4” z6 - 1-3/4” z20 4080000611 4080000611
248220007R021 248230006R021432000006R88 432000006R88
6
7
10
56
8
9
10
H R
Ø
A
21
8
3 4 5 4 6 4 7 4 6 9 10
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
86
400
N•m H Ø A R FD1 R FD2
63,5 1 3/8” Z6 155 677124103 17822600 70 1 3/8” Z6 67723210323,81000 84 1 3/8” Z6 -271100
911 3/8” Z6 -
30,21200 1 3/8” Z6 -
1 3/8” Z6 -30,21450 103
1 3/4” Z6 -
FD3
----
677548303677653303677653304
R
202--
677444203677546203
---
155155155155155155
178178178178178178
202202202202202202
Ref. Description Qty. FD1 Qty. FD2 Qty. FD3
FD1 - FD2 - FD3 FRICTION TORQUE LIMITERS
2 3 4 31
5
6 7 7 8 9
ARH
Ø
12
5
6
4
1
2
3
4
5
6
7
89
303001400825301610112530261011
--------
122 mm 247006151R082142 mm --162 mm --1-3/8” z6 51361030111-3/8” z21 --1-3/4” z6 --1-3/8”z6 403000001R1011-3/4”z6 --
24861000112,5 mm 367003610-3,0 mm 367001610-3,5 mm 367002610-4,0 mm --
24600001712646100011
8--
11---2-1--1-1----11
303001400--
253046201253056201
---
247006251R08-
513620301--
403000009R10-
248620001367005620367003620367001620
-246000018264620001
8----111--2111111----11
303003400-
--
-253056301253066301253076301
--
247006351R08513630301513633701513630401
403000009R10403000011R10
248630001--
367002630367001630246000019264630001
for size 1for size 2for size 3for size 4for size 5for size 6for size 7
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
87
1200
N•m H Ø A R FD22 R FD33
91 1 3/8” Z6 178 677548703 -30,21450 103 1 3/8” Z6 178 677653703 -30,2
1 3/4” Z6 178 677653704 -1800 117 1 3/8” Z6 178 677858703 -35
1 3/4” Z6 178 677858704 -2100 117 1 3/8” Z6 - 202 67786180335
1 3/4” Z6 2022400 119 1 3/8” Z6 20241
1 3/4” Z6 202
1 3/4” Z6 2022800 130,5 1 3/8” Z6 20241
677861804677964803677964804677068803677068804
Ref. Description Qty. FD22 Qty. FD33
FD22 - FD33 FRICTION TORQUE LIMITERS
21 3 4 3 5 3 6 3 8 9 9 10 11
7
ARH
Ø
5
6
8
9
10
1
2
3
45
8
9
3030024008 30300440082530562011 25305630112530662011 2530663011
for size 7 2530762011 2530763011for size 8 2530862011 2530863011for size 9 -- 2530963011for size 10 -- 2531063011142 mm 247006251R084 --162 mm -- 247006351R084
2487277011 24873770113 mm 2487200011 24873000111-3/8” z6 5137203011 51373030111-3/8” z21 5137237011 51373370111-3/4” z6 5137204011 51373040111-3/4” z20 5137238011 51373380111-3/8” z6 - 1-3/8” z21 403000009R102 403000009R1021-3/4” z6 - 1-3/4”z20 403000011R101 403000011R101
2486200011 24863000112,5 mm 367005620- --3 mm 367003620- --3,5 mm 367001620- 367002630-4 mm -- 367001630-
6
7
1011
2460000181 24600001912647200011 2647300011
for size 5for size 6
----
--
---
--
---
--
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
88
1000
H Ø A R FT32 R FT42
841 3/8” Z6 6LE344003R271 3/8” Z21
1806LE344037R
1100 911 3/8” Z6 6LG346003R
30,21 3/8” Z21 6LG346037R
1200
1 3/8” Z6
91 1 3/8” Z2130,2
1 3/4” Z20202
103
1 3/8” Z6
30,21450 1 3/8” Z21
N•m
6LG448003R6LG448037R6LG448038R6LH453003R6LH453037R
1 3/4” Z20 6LH453038R
Ref. Description Qty. FT32 Qty. FT42
4
5
6
1
234
5
9
2530386011 --2530486021 --2530589011 2530587011
for size 6 2530689031 2530690011for size 7 2530786011 2530787021
258005320R021 258005320R021M10x50 4320000538 4320000538
2400002131 24000021411-3/8”z6 5158603051 51587030511-3/8”z21 5158637051 51587370511-3/4”z6 51587040511-3/4”z20 5158738051141 mm 247006251R082162 mm 247006351R0828 mm 2488600051 24887000512,5 mm 367003860-2,75 mm 367002860-3,0 mm 367001860-3,25 mm 367004870-3,30 mm 367005860-3,5 mm 367001180- 367003870-3,75 mm 367001870-
6
10
111-3/8” z6 - 1-3/8” z21 4080000601 40800006011-3/4” z6 - 1-3/4” z20 - 4080000611
for size 3for size 4for size 5
AH R
Ø
1 23 106 6 9 45
1
FT32 - FT42 FRICTION TORQUE LIMITERS
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
89
1200
H Ø A R FT34 R FT44
911 3/8” Z6 6LG748003R
30,21 3/8” Z21
180
6LG748037R
1450
1 3/8” Z6 6LH753003R
103 1 3/8” Z21 6LH753037R30,21 3/4” Z201 3/8” Z61 3/8” Z21
202
35,01800 117 1 3/4” Z61 3/4” Z20
N•m
6LM861003R6LM861037R6LM861004R6LM861038R
6LH753038R6LM758003R6LM758037R6LM758004R6LM758038R
Ref. Description Qty. FT34 Qty. FT44
---
FT34 - FT44 FRICTION TORQUE LIMITERS
5
6
8
1
234
5
7
2530589011 25305870112530689031 25306900112530786011 25307870212530889031 2530890011
- 2530987021- 2531087021
258005320R021 258005320R0214320000538 43200005382400002181 24000021915158903051 51590030515158937051 51590370515158904051 51590040515158938051 5159038051
247006251R084247006351R084
Driving Plate 2487277011 24873770114 mm 2488600011 2488700111
2488600051 2488700051367003860-367002860-367001860-
367004870-
6
10
11
367005860-367001180- 367003870-
367001870-367001190-
4080000601 4080000601-- 4080000611
89
M10x50
1-3/8”z61-3/8”z211-3/4”z61-3/4”z20141 mm
162 mm
2,5 mm2,75 mm3,0 mm3,25 mm3,3 mm3,5 mm3,75 mm4,0 mm1-3/8” z61-3/4” z6
8 mm
AH R
Ø
for size 8for size 9
for size 5for size 6for size 7
for size 10
1 23 6 8 6 7 6 5 6 9 4 10
1
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
90
FN22 FRICTION TORQUE LIMITERS
Ø
AH R
1200
1450
1700
1800
H Ø A R FN22
687548703R
687653703R
687757703R
687858703R
N•m
5
6
7
8
91
103
106
117
30,2
30,2
35
35
1 3/8” Z6 178
Ref. Description Qty. FN22
1
2345
9
253058301125306830112530783011
for size 8 25308830113030024008
4112
1-3/8” z6
6
12
16
for size 5for size 6for size 7
141 mm 247006251R08248830001248720001338001064
7 1 246000024
8 1 427220101
1 34801700010 1 421955001R0311 1 403000001R10
1
1314
15
1513830301246000025
1 248620001
for size 8
for size 5 thickness 2,5 mmfor size 6 thickness 3 mm
for size 7
2
2
222
171
1
thickness 3 mmthickness 3,5 mm
thickness 3,5 mm
367005620367003620
367003620
367001620367001620246000018264720001
2
1 4 5 6 8
10
12 14 153 3 3 7
11
13 6 3 15 16 179
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
91
FN24 FRICTION TORQUE LIMITERS
1200
1450
1700
1800
H Ø A R FN24
659548103R659548137R659653103R659653137R659653103R659757137R659858103R659858137R
N•m
5
6
7
8
91
103
106
117
30,2
30,2
35
35
1 3/8” Z6
181
1 3/8” Z211 3/8” Z61 3/8” Z211 3/8” Z61 3/8” Z211 3/8” Z61 3/8” Z21
Ref. Description Qty. FN24
1
2345
9
253058901125306890312530786011
for size 8 2530889031432000045R088
1411
1-3/8” z6
6
12
16
for size 5for size 6for size 7
D=141 mm258005331R02247006251R08
248830001248860001
7 1 348017000
8 1 427830106
1 33800106410 1 24600002411 1 421955001R03
1
13
1415
1408000048408000048
1 515830302
for size 8 thickness 3,5 mm
for size 5 thickness 2,5 mmfor size 6 thickness 3 mmfor size 7 thickness 3,3 mm
1
1
111
171
1
515833702
246000025248860005240000218367003860367001860
367005860
Ø
A
1-3/8” z211-3/8” z6
1-3/8” z21
1 367005860
1
2
3 4 5 4 6 4 7 8 4 9 10
11
13
12
14 9 15 16 17
1
LRS/R006 100 SERIES
COM
PON
ENTS
OUT
OF
PRO
DUCT
ION
- O
NLY
AVA
ILAB
LE A
S SP
ARE
PART
S
LRS/R006 100 SERIES
The codes above come with labels and instructions suitable for mostcountries. For North America, replace "FX" with "UC", for Japanreplace "FX" with "JP", and for CE mark, replace "FX" with "CE."Refer to page 7 - 8 for further information on labels and instructions.
LENGTHL (mm)
CODE
L L
COMPLETE SHIELD KITS
92
086 121860 1210
1
43
100400
2
3
4
5
6
7
8
9
10
5F01086FFFX
5F02086FFFX
--
5F43086FFFX
5F04086FFFX
5F05086FFFX
5F06086FFFX
5F07086FFFX
5F08086FFFX
--
--
5F01121FFFX
5F02121FFFX
--
5F43121FFFX
5F04121FFFX
5F05121FFFX
5F06121FFFX
5F07121FFFX
5F08121FFFX
--
--
XXXXXXX
650
660
670
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
LENGTHL (mm)
CODE 086 121860 1210
652 5F02086R1652FX 5F02121R1652FX
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
L
LENGTHL (mm)
CODE 086 121860 1210
672 5F02086R9672FX 5F02121R9672FX
LENGTHL (mm)
CODE 086 121860 1210
662 5F02086F9662FX 5F02121F9662FX
654 5F02086R1654FX 5F02121R1654FX
656 5F02086R1656FX 5F02121R1656FX
658 5F02086R1658FX 5F02121R1658FX
664 5F02086F9664FX 5F02121F9664FX
666 5F02086F9666FX 5F02121F9666FX
668 5F02086F9668FX 5F02121F9668FX
674 5F02086R9674FX 5F02121R9674FX
676 5F02086R9676FX 5F02121R9676FX
678 5F02086R9678FX 5F02121R9678FX
XXXX
XXX
L
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
LRS/R006 100 SERIES 93
*
12
3-4345678910
1* 2 3 4 5 L=086 7 8 9 106 L=086
219010001
219040001
219050001
219080005
219080001
517010011
517040011
517050011
517080111
517080011
517010030
517040030
517050030
517080130
517080030
255010005R02255020005R02
255040005R02
255050005R02
255060005R02
255080005R02
255010006R02255020006R02
255040006R02
255050006R02
255060006R02
255080006R02
252000001R02
252000005R02
517010020
517040020
517050020
517080120
517080020
517010012
517040012
517050012
517080112
517080012
236660694
236680676
236830650
236850602
236650694
236670676
236820650
236840602
Dim.
Standard (#1) style end cone
A
SHIELD BEARING SUPPORT RINGS
12
43-45
6-78-9-10
30,4
40,4
46,4
53,4
59,4
68,4
Amm
255010006R02
255020006R02
255040006R02
255050006R02
255060006R02
255080006R02
255010005R02
255020005R02
255040005R02
255050005R02
255060005R02
255080005R02
INNER TUBE OUTER TUBE
40,4
47,4
53,4
62,4
68,4
80,4
Amm
1 2 4 5 610 1
9
7
3
8
94 LRS/R006 100 SERIES
The codes above come with labels and instructions suitable for mostcountries. For North America, replace "FX" with "UC", for Japanreplace "FX" with "JP", and for CE mark, replace "FX" with "CE".Refer to page 7-8 for further information on labels and instructions.
L
L
L
LENGTHL (mm)
CODE
LENGTHL (mm)
CODE
LENGTHL (mm)
CODE
086 121860 1210
086 121860 1210
086 121860 1210
50°
50°
80°- 50°
5F04086K1FX
5F06086K1FX
5F08086K1FX
5F04121K1FX
5F06121K1FX
5F08121K1FX
5F04086KKFX
5F06086KKFX
5F08086KKFX
5F04121KKFX
5F06121KKFX
5F08121KKFX
5F04086WKFX
5F06086WKFX
5F08086WKFX
5F04121WKFX
5F06121WKFX
5F08121WKFX
4
6
8
4
6
8
4
6
8
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
LENGTHL (mm)
CODE
L
L
LENGTHL (mm)
CODE
086 121860 1210
086 121860 1210
4
6
8
80°
80°
5F04086W1FX
5F06086W1FX
5F08086W1FX
5F04121W1FX
5F06121W1FX
5F08121W1FX
5F04086WWFX
5F06086WWFX
5F08086WWFX
5F04121WWFX
5F06121WWFX
5F08121WWFX
4
6
8
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
XXXX
XXX
399C
EE
051
BONDIOLI & PAVESI S.p.AP.O.BOX 30/A - 46029 SUZZARA (MN) - ITALY
95LRS/R006 100 SERIES
CF IMPLEMENT INPUT CONNECTION SHIELDSThe Machinery Directive (98/37/CEE) requiresthat the implement be equipped with animplement input connection shield fixed tothe machine.
Standard EN1553 requires the implementinput connection shield to completely encirclethe shaft, but allow for installation andarticulation of the driveline.
Standards EN1553 and ASAE S318.15 requirethe implement input connection shield tooverlap the intergral driveline guard by atleast 50 mm in the straight position.
The tractor master shield, the integral drivelineguard, and the implement input connectionshield form an interactive guarding systemaccording to ASAE S318.15. Bondioli &Pavesi recommends that driveline guards,master shields, and implement inputconnection shields always be used.
Any damaged or missing shields should bereplaced with original equipment spare parts.
Bondioli & Pavesi recommends that theimplement manufacturer affix a label on theimplement warning of the hazards involvedand the need to maintain the shields in placeand in proper working order. It is also
recommended that the owner's manualprovided by the implement manufacturerindicate the implement input connectionshield and labels, and provide informationfor obtaining replacements.
In accordance with standards EN 1553 andASAE S493.1, the implement manufacturershould provide a label stating that the machineshould not be operated when the implementinput connecton shield is opened or removed.
Bondioli & Pavesi implement input connectionshields are not designed nor intended to beused as steps.
cod.
399
CE
E1C
F/C
- 0
504
MADE IN ITALY
Implement input connection shields destinedfor used in CEE-EFTA countries are providedwith an instruction sheet and the Declarationof Conformity according to the MachineryDirective (98/37/CEE).
cod.
399
CE
E1C
F/C
- 0
504
MADE IN ITALY
Add the suffix "CE" to the code tospecify the instruction sheet andDeclaration of Conformity for CEE-EFTA countries.
96
CF IMPLEMENT INPUT CONNECTION SHIELDS
LRS/R006 100 SERIES
1
8
43
7654
221902
41701
41702
41703
41702
SINGLECARDANJOINT
RA GE SA1-2LN1-2
LBSA3-4LN3-4
LR FV-FNVFFV-FFNVFT-FNT
41714014171402
41714014171402
41702
41712
41713
21902
41714014171402
41714014171402
41704
41714014171402
21904
21913
21913
21913
50° AND 70°CV JOINTS
Code 21904, 41704 and 41714 IIC shields canbe supplied with one or two windows that giveaccess for the installation of the driveline orchecking that is properly secured.To specify an IIC shield with access window(s),add the suffix “01” to the code for one opening,or add “02” for two openings.The implement input connection shields 21904,41704 and 41714 can be supplied in Zytel®upon customer request.This material maintains its strength at elevatedtemperatures. Shields made of Zytel® can beused to guard devices operating at temperatureshigher than normal, such as friction torquelimiters working in heavy duty conditions.
120
58
120
190
120
58
230280
134
230
150
240
160
203
11015
0
150
203
150
190
150
250
58
58 210 260
250
280
180
Cone w/ Long Extension
Code 41711
Cone w/ Long Extension
Code 41712
Cone w/ Long Extension
Code 41713
Cone w/ Long Extension
Code 41714
Cone w/ Medium Extension
41701
Cone w/ Medium Extension
41702
Cone w/ Medium Extension
41703
Cone w/ Medium Extension
41704
21901
Base Cone
21902
Base Cone
21903
Base Cone
21904
Base Cone