10 feet - star pipe products - ductile iron pipe fittings, joint …starpipeproducts.com/pdf/soil...
TRANSCRIPT
Cast Iron Soil Pipe Products
SUBMITTAL
Hubless Pipe & Fittings
J
T
B
HUBLESS PIPE 10 FEET*
NOM. SIZE
BINSIDE
DIAMETER
JOUTSIDE
DIAMETER
T WT (LBS.)NOM. MIN
1 1/2 1.50 1.90 0.16 0.13 28.42 1.96 2.35 0.16 0.13 36.33 2.96 3.35 0.16 0.13 52.14 3.94 4.38 0.19 0.15 77.25 4.94 5.30 0.19 0.15 95.66 5.94 6.30 0.19 0.15 113.58 7.94 8.38 0.23 0.17 181.910 10.00 10.56 0.28 0.22 276.712 11.94 12.50 0.28 0.22 364.215 15.11 15.83 0.36 0.30 542.0
*All dimensions in inches except where indicated. Note: All dimensions and tolerances are from ASTM A-888 and CISPI 301 Hubless Pipe & Fittings.
10 FEET
APPROvALS & STANDARDS• UPC Listed through IAPMO R&T laboratory• CertifiedtoconformtoASTM A888-StandardSpecificationforHublessCastIronSoilPipeandFitttingsforSanitary
andStormDrain,Waste,andVentPipingApplicationsthroughIAPMOR&Tlaboratory• CertifiedtoconformtoCISPI 301-StandardSpecificationsforHublessCastIronSoilPipeandFittingsforSanitaryand
StormDrain,Waste,andVentPipingApplicationsthroughIAPMOR&Tlaboratory• Star®PipeProductsHublessCastIronSoilPipeandFittingsmeettherequirementsofICC International Plumbing
Code 2006formaterialsasoutlinedinChapter7forsanitarydrainagesystems(sections702,705,&708)• OSHPD compliant as per CANs 2001 and CANs2007 as per CPC section 701.1
Quarter Bend Double Quarter Bend P-Trapw/ 1/2" Primer Tap
San Cross
Wye ShortReducer
San TeeDouble Combination Wye & 1/8" Bend
Manufacturer’s
www.starpipeproducts.com ®REGISTEREDTRADEMARKOFSTARPIPEPRODUCTS
STAR®PIPEPRODUCTS-PLUMBING DIvISION4018WestHollowParkway▪Houston,TX77082
1-877-909-7827FAX866-868-7827
QUALITY SYSTEM
REG I S T R ATION
® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway ▪ Houston, TX 77082
1-877-909-7827 FAX 866-868-7827
Cast Iron Soil Pipe Products
SUBMITTAL
Hub & Spigot Pipe & FittingsService Weight (SV)
*All dimensions in inches except where indicated. Note: All dimensions and tolerances are from ASTM A-74
APPrOVALS & STANDArDSUPC Listed• through IAPMO R&T laboratoryCertified to conform to • ASTM A-74 - Standard Specification for Cast Iron Soil Pipe and FitttingsStar• ® Pipe Products SV Cast Iron Soil Pipe and Fittings meet the requirements of ICC International Plumbing Code 2006 for materials as outlined in Chapter 7 for sanitary drainage systems (sections 702, 705, & 708).SV Gaskets conform to ASTM C564 - Standard Specification for Rubber Gaskets for Cast Iron Soil Pipe & Fittings.•
www.starpipeproducts.com
DETAILS OF HUB & SPIGOT FOr SV*INSIDE
DIAMETEr HUB
INSIDE DIAMETEr
BArrEL
OUTSIDE DIA.OF BArrEL THICKNESS OF BArrEL TELESCOPING
LENGTH
NOM.SIZE A B C J T-NOM T-MIN Y
2 2.94 ±0.06 1.96 ±0.09 3.62 2.30 ±0.09 0.17 0.14 2.50 ±0.09
3 3.94 +0.09-0.06 2.96 ±0.09 4.68 3.30 ±0.09 0.17 0.14 2.75 ±0.09
4 4.94 +0.09-0.06 3.94 ±0.09 5.68 4.30 ±0.09 0.18 0.15 3.00 ±0.09
5 5.94 +0.09-0.06 4.94 ±0.09 6.68 5.30 ±0.09 0.18 0.15 3.00 ±0.09
6 6.94 +0.09-0.06 5.94 ±0.09 7.68 6.30 ±0.09 0.18 0.15 3.00 ±0.09
8 9.25 ±0.13 7.94 ±0.13 10.13 8.38 ±0.13 0.23 0.17 3.50 ±0.13
10 11.38 ±0.13 9.94 ±0.13 12.44 10.50 ±0.13 0.28 0.22 3.50 ±0.13
12 13.50 ±0.13 11.94 ±0.19 14.56 12.50 ±0.19 0.28 0.22 4.25 ±0.19
15 16.95 ±0.13 15.16 ±0.19 18.11 15.88 ±0.19 0.36 0.22 4.25 ±0.19
3½', 5' & 10'Laying Length
STAR 4" x 10' SV PIPE UPC® ASTM A-74 XXX XXX XXX
Manufacturer’s Registration Trademark
Countryof Origin
Dateof Manufacturing
SHOrT SWEEP BEND - 90º SANITArY TEE P-TrAP WYE COMBINATION WYEAND 1/8 BEND
A
B
Y( Telescoping Length ) Laying Length
J
T
C
QUALITY
QUALITY SYSTEM
REG I S T R ATION
Cast Iron Soil Pipe Products
SUBMITTAL
Standard 60 Coupling
Standard 60 Coupling
STAndArdS & SpeCIfICATIonS• CertifiedtocomplywithASTMC1277StandardSpecificationforHublessCouplings.
• ListedthroughIAPMOfile#6200forcompliancetoUPCandASTMC1277.
• GasketcomplieswithASTMC564.
• CouplingsconformtoCISPI310.
feATUreS• 3rd party Listed to ASTM C1277 Standards: Independently3rdpartylisted byIAPMOforcomplianceto
theASTMC1277standardforhublesscouplings(file#6200).
• Clamp Assembly: AllStainlessSteelclampassemblyfeaturesbandsrivetedtotheshieldwithboth
fixedandflexiblestainlesssteeleyelets.
• optimum Shield design: Corrugatedpatternbrightannealedstainlesssteelshieldeffectivelytransfers
compressionevenlythroughthegasketprovidinganimprovedsealandrestraintcapability.
• Gasket:ManufacturedfrompremiumvirginNeopreneelastomerresultinginsuperiorperformance
characteristicsunderawiderangeofinstallationconditions.
www.starpipeproducts.comREV:090209-02
®REGISTEREDTRADEMARKOFSTARPIPEPRODUCTS
STAR®PIPEPRODUCTS-pLUMBInG dIVISIon4018WestHollowParkway▪Houston,TX77082
1-877-909-7827FAX866-868-7827
MATerIALSSHIELD: Type301AISIStainlessSteel,BrightAnnealed
BAND: Type301AISIStainlessSteel
SCREWHOUSING: Type301AISIStainlessSteel
SCREW: Type305AISIStainlessSteel,5/16”hexhead
EYELETS: Type300AISIStainlessSteel,fixedandflexible
GASKET: Neopreneelastomer
STAndArd 60 noM. ITeM # of BAndS InSTALLATIon
SIZe (In.) Code per CoUpLInG TorQUe (In.-LBS.)
11⁄2 NHC0150SD 2 60
2 NHC0200SD 2 60
3 NHC0300SD 2 60
4 NHC0400SD 2 60
5 NHC0500SD 4 60
6 NHC0600SD 4 60
8 NHC0800SD 4 60
10 NHC1000SD 4 60
Cast Iron Soil Pipe Products
SUBMITTAL
Heavy 80 Wide Body Coupling
Heavy 80 Wide Body Coupling - Blue Shield
STANDARDS & SPECIFICATIONS• Certifi ed to comply with ASTM C1540 Standard Specifi cation for Heavy Duty Hubless Couplings• Listed through IAPMO fi le #6199 for compliance to UPC and ASTM C1540• FM approved to FM 1680 standard Class I 15 PSI• Gasket complies with ASTM C564
FEATURES3rd Party Listed to ASTM C1540 Standards: • Independently 3rd party listed by IAPMO for compliance to the ASTM C1540 standard for Heavy Duty hubless
couplings (fi le #6199).Engineered Clamp Assembly: • All Stainless Steel clamp assembly features bands riveted to the shield with both fi xed and longer fl exible eyelets.
Screw housing interlocks with the band providing a reliable assembly even when screws are torqued up to 125% of stated installation torque.
• Long fl exible eyelet slot allows increased independent movement of the band while tightening which helps pre-vent shield crimping and results in a coupling suitable for joining pipe and fi ttings with minimum/maximum toler-ance conditions.
Optimum Shield Design: • Through rigorous testing and evaluation, Star engineers have optimized the shield design to provide maximum joint
rigidity, along with the enhanced ability to transfer torque loads to the gasket.• Corrugated pattern bright annealed stainless steel shield effectively transfers compression evenly through the gas-
ket providing an improved seal and restraint capability.Gasket: • Manufactured from premium virgin Neoprene elastomer resulting in superior performance characteristics under a
wide range of installation conditions.
www.starpipeproducts.com ® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway � Houston, TX 77082
1-877-909-7827 FAX 866-868-7827
MATERIALSSHIELD: Series 300 AISI Bright Annealed Stainless SteelBAND: Series 300 AISI Stainless SteelSCREW HOUSING: Series 300 AISI Stainless SteelSCREW: Type 305 AISI Stainless Steel, 5/16” hex headEYELETS: Series 300 AISI Stainless Steel, fi xed and fl exibleGASKET: Neoprene elastomer
HEAVY 80 WIDE BODYNOM. ITEM # OF BANDS INSTALLATION
SIZE (IN.) CODE PER COUPLING TORQUE (IN.-LBS.)
11⁄2 NHC0150HD 4 80
2 NHC0200HD 4 80
3 NHC0300HD 4 80
4 NHC0400HD 4 80
5 NHC0500HD 6 80
6 NHC0600HD 6 80
8 NHC0800HD 6 80
10 NHC1000HD 6 80
REV:090209-03
APPROVED
Cast Iron Soil Pipe Products
SUBMITTAL
Super Heavy 80 Wide Body Coupling
Super Heavy 80 Wide Body Coupling - Red Shield
STANDARDS & SPECIFICATIONS• Certifi ed to comply with ASTM C1540 Standard Specifi cation for Heavy Duty Hubless Couplings• Listed through IAPMO fi le #6199 for compliance to UPC and ASTM C1540• FM approved to FM 1680 standard Class I 15 PSI• Gasket complies with ASTM C564
MATERIALSSHIELD Type 304 AISI Bright Annealed Stainless SteelBAND: Type 304 AISI Stainless SteelSCREW HOUSING: Type 304 AISI Stainless SteelSCREW: Type 305 AISI Stainless Steel, 3/8” hex headEYELETS: Series 300 AISI Stainless Steel, fi xed and fl exibleGASKET: Neoprene elastomer
FEATURES3rd Party Listed to ASTM C1540 Standards: • Independently 3rd party listed by IAPMO for compliance to the ASTM C1540 standard for Heavy Duty hubless
couplings (fi le #6199).Engineered Clamp Assembly: • All Stainless Steel clamp assembly features bands riveted to the shield with both fi xed and longer fl exible eyelets.• Super Heavy 3/8” hex head screws with extra long conical head engage smoothly with the clamp bands and
hold the joint in the most challenging installation conditions.• Screw housing interlocks with the band providing a reliable assembly even when screws are torqued up to 125%
of stated installation torque.• Long fl exible eyelet slot allows increased independent movement of the band while tightening which helps
prevent shield crimping and results in a coupling suitable for joining pipe and fi ttings with minimum/maximum tolerance conditions.
Optimum Shield Design: • Through rigorous testing and evaluation, Star engineers have optimized the shield design to provide maximum
joint rigidity, along with the enhanced ability to transfer torque loads to the gasket.• Corrugated pattern bright annealed stainless steel shield effectively transfers compression evenly through the
gasket providing an improved seal and restraint capability.Gasket: • Manufactured from premium virgin Neoprene elastomer resulting in superior performance characteristics
under a wide range of installation conditions.
www.starpipeproducts.com ® REGISTERED TRADEMARK OF STAR PIPE PRODUCTS
STAR® PIPE PRODUCTS - PLUMBING DIVISION4018 West Hollow Parkway � Houston, TX 77082
1-877-909-7827 FAX 866-868-7827
SUPER HEAVY 80 WIDE BODYNOM. ITEM # OF BANDS INSTALLATION
SIZE (IN.) CODE PER COUPLING TORQUE (IN.-LBS.)
11⁄2 NHC0150SHD 4 80
2 NHC0200SHD 4 80
3 NHC0300SHD 4 80
4 NHC0400SHD 4 80
5 NHC0500SHD 6 80
6 NHC0600SHD 6 80
8 NHC0800SHD 6 80
10 NHC1000SHD 6 80
REV:090209-03
APPROVED
SUBMITTAL
STANDARD NO-HUB COUPLING
No-Hub ClassicTM Couplings are engineered
to connect no-hub cast iron pipe in applications
replacing the less-efficient hub & spigot material.
The couplings consists of a high quality
elastomeric compound (ASTM C 564) gasket
housed inside a 301 stainless steel corrugated
shield. Shield is 0.007” thick. Depending on the
size of the shield, two or four 301 stainless steel
clamps encircle the shield and provide the
sealing force. The 5/16” hex-head screws are
305 stainless steel. Available in sizes ranging
from 1-1/2” – 10”. The couplings are designed
for installation torque of 60 in-lbs. The entire
coupling is corrosion resistant. Conforms to
ASTM C1277 and CISPI 310.
Sizes 1-1/2”, 2”, 3”, and 4” consist of a 2-1/8”
wide corrugated 301 stainless steel shield with
two stainless steel clamps mounted in a series
and secured with fixed and floating eyelets to
allow the clamp to travel during tightening.
Sizes 5” and 6” consist of a 3” wide corrugated
301 stainless steel shield with four clamps.
Sizes 8” and 10” consist of a 4” wide
corrugated 301 stainless steel shield with four
stainless steel clamps.
Date:
Project:
Architect:
Contractor: Engineer:
Size Installation
Torque Inch Pounds
No. of Clamps
Per Coupling
1-1\2" 60 2 2" 60 2 3" 60 2 4" 60 2 5" 60 4 6" 60 4 8" 60 4 10" 60 4
2” X 1-1/2” 60 2 3” x 2” 60 2 4” x 3” 60 2
Materials
Band & Housing: Type 301 AISI stainless steel Screw: Type 305 AISI stainless steel,
5/16” hex head Shield: Type 301 AISI stainless steel,
corrugated, thickness 0.007” Gasket: The gasket shall be fabricated
from a high quality elastomeric compound (ASTM C 564).
A product of AIPSA, Matamoros, Mexico Spec No. S1NHC
4/3/07 BB
SUBMITTAL 12” AND 15” HEAVY-DUTY
NO-HUB COUPLINGS _______________________
Date _______________________________
Architect _______________________________
Project _______________________________
Contractor _______________________________
Engineer IDEAL® patented No-Hub Couplings are engineered to connect no-hub cast iron pipe in applications replacing the less-efficient hub & spigot material. The Couplings consists of an elastomeric compound gasket (ASTM C-564) housed inside a 304 stainless steel corrugated shield. Six (6) 304 stainless steel clamps surround the shield and provide the sealing force. The 3/8” hex-head screws are made from 305 stainless steel. The couplings are designed for installation torque of 120 in-lbs. The entire coupling is corrosion resistant.
12” & 15” Heavy-Duty No - Hub Couplings
Size Part No.
Installation Torque Inch
Pounds No. of Clamps Per Coupling
12” 6231M8G 120 6 15" 6232M8G 120 6
The Design The IDEAL® 12” and 15” Heavy-Duty No-Hub Coupling are engineered to provide superior performance at a very competitive cost. Conforms to ASTM C-1277.
The Gasket Made from high-quality elastomeric compound (ASTM C-564), the IDEAL® No-Hub gasket features a pattern of multiple, thick sealing sectors and adjacent groove sectors laterally spaced. When the clamps are tightened, this pattern permits the clamping bands and the shield to form a restriction impeding the movement of the shield relative to the gasket.
The Shield 0.008” thick type 304 stainless steel shield requires less band load to transfer pressure to the gasket, leaving more clamping load in reserve to compress the gasket. The patented, bi-directional corrugations create clamp sealing pressure in both parallel and transverse patterns on the gasket and pipe, thereby avoiding pull-out failures, and providing a positive, reliable seal. In addition, the shield design adjusts to differences in the circumference and outside diameters of the pipes being joined. This eliminates gasket wrinkling and thereby eliminating leak paths. The Clamps Heavy-duty 304 stainless steel clamps and 3/8” hex-head 305 screws provide the sealing force. Both the 12” and the 15” coupling use six (6) 5/8” wide clamps. The entire assembly is corrosion resistant.
4/3/07 BB
12” & 15” NO-HUB COUPLINGS Product Information Submittal for No-Hub Systems
TEST GASKET PHYSICAL TEST MIN. OR MAX. REQUIREMENTS
ASTM METHOD
Tensile Strength
1500 psi min. D 412
Elongation 250 min. D 412 Durometer (Shore A)
70 +/-5 @ 76°F +/- 5°F D 2240
Accelerated Aging
15% maximum tensile and 20% maximum elongation, 10 points maximum increase in hardness, all determinations after oven aging for 96 hours at 158°F
D573
Compression Set
25% max. after 22 hours at 158°F D 395 Method B
Oil Immersion 80% max. volume change after immersion in IRM 903 for 70 hours at 212°F.
D 471
Ozone Cracking
No visible cracking at 2 times magnification of the gasket after 100 hours exposure in 1.5 ppm ozone concentration at 104°F. Testing and inspection to be on gasket which is loop mounted to give approximately 20% elongation of outer surface.
D1149
Tear Resistance
150 lbf /in. min. D 624
Water Absorption
20% max. by weight after 7 days at 158°F D 471
The IDEAL® No-Hub Coupling has been engineered to provide an all stainless steel coupling; balancing the desire for a more rigid joint with the need to provide a superior, positive, reliable seal which can accommodate possible disparities in the mating of No-Hub pipe and fittings. This has been accomplished by manufacturing our coupling with our standard corrugated shield of sufficient width to accommodate additional surface-bearing sealing clamps. The additional sealing clamps, when torqued to 120 in-lbs., deliver additional performance benefits. First, the overall dimensional thickness of the clamp and shield, in conjunction with the additional width of the coupling, result in a more uniformly rigid joint, with the load being supported at both the outer edge of the coupling and the centerline of the joint. Second, the additional sealing clamps yield increased surface-bearing contact between the coupling and the pipe or fittings, thereby inhibiting joint movement at higher internal pressures not commonly associated with DWV systems. The 12” and 15” diameter couplings consist of a 5 1/2” wide bi-directional, corrugated 304 stainless steel shield in conjunction with six (6) stainless steel clamps mounted in a series, secured in place by means of fixed and “floating” eyelets to allow the clamp “travel” during tightening.
MATERIALS Clamp: Type 304 AISI stainless steel Screw: Type 305 AISI stainless steel 3/8” hex head/shoulder Shield: Type 304 AISI stainless steel, corrugated. Shield thickness 0.008” Gasket: The gasket is made of an elastomeric compound that meets the requirements of
ASTM C-564.