1. engg mechanics
TRANSCRIPT
Civil EngineeringPaper-I
Publications
Civil ServicesMain Examination
Previous Solved Papers
(1995-2020)
Also useful for Engineering Services Main Examination, Indian Forest Service Examination and
various State Engineering Services Examinations
Topicwise Presentation
Years26
MADE EASY Publications Pvt. Ltd.
Corporate Office: 44-A/4, Kalu Sarai (Near Hauz Khas Metro Station), New Delhi-110016E-mail: [email protected]: 011-45124660, 8860378007
Visit us at: www.madeeasypublications.org
Civil Services Main Examination Previous Years Solved Papers : Civil Engineering (Paper-I)© Copyright, by MADE EASY Publications Pvt. Ltd.All rights are reserved. No part of this publication may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photo-copying, recording or otherwise), without the prior written permission of the above mentioned publisher of this book.
First Edition: 2017
Second Edition: 2018
Third Edition: 2019
Fourth Edition: 2020
Fifth Edition: 2021
© All rights reserved by MADE EASY PUBLICATIONS Pvt. Ltd. No part of this book may be reproduced or utilized in any form without the written permission from the publisher.
Publications
Civil Services Examination is considered as most prestigious
job in India which is being preferred by engineers now-a-days.
There was a need of good book, which contains error free
questions with apt solutions that even a begineer student can
understand. I am glad to launch the second edition of this book.
MADE EASY team has made deep study of previous exam
papers of Civil Services Main Examination and observed that
a good percentage of questions has been asked in Engineering
Services Examination, Indian Forest Service Examination as well as State Services Examination.
Therefore it is advisable to study this book before one takes the exam. This book is also useful for ESE
Main appearing candidates and other competitive examinations for engineering graduates.
The second edition of this book is prepared with due care to provide complete solutions to all
questions with accuracy. I would like to give credit of publishing this book to MADE EASY Team for
their hard efforts in solving previous years papers in a limited time frame.
I have true desire to serve student community by providing good source of study and quality guidance.
I hope this book will be proved as an important tool to succeed in competitive examinations. Any
suggestions from the readers for improvement of this book are most welcome.
With Best Wishes
B. Singh
CMD, MADE EASY Group
Preface
Sl. TOPIC PAGE No.
Unit-1 Engineering Mechanics ...........................................................................1-33
1. Composition, Resolution and Equilibrium of Forces .......................................... 1
2. Friction ..............................................................................................................................14
3. Kinematics of Translational and Rotational Motion .........................................24
4. Work and Energy ...........................................................................................................29
5. Center of Gravity and Moment of Inertia .............................................................30
Unit-2 Strength of Materials .......................................................................... 34-103
1. Properties of Metals and Basic Concepts .............................................................34
2. Shear Force and Bending Moment .........................................................................40
3. Bending Stresses and Shear Stresses .....................................................................58
4. Torsion ..............................................................................................................................72
5. Principal Stress & Principal Strain [Not in Syllabus] ..........................................77
6. Theories of Failure ........................................................................................................79
7. Deflection of Beams .....................................................................................................79
8. Columns ...........................................................................................................................97
Unit-3 Structural Analysis ............................................................................ 104-226
1. Influence Line Diagram and Rolling Loads ........................................................104
2. Arches and Suspension Bridges ............................................................................137
3. Methods of Structural Analysis ..............................................................................146
4. Trusses .............................................................................................................................198
5. Matrix Method of Structural Analysis ..................................................................221
Unit-4 Structural Steel Design ..................................................................... 227-299
1. Connections (Bolted & Welded Eccentric Connections) ...............................227
2. Compression Member ...............................................................................................245
3. Tension Members ........................................................................................................264
Civil Services Main Examination
C O N T E N T S
Previous Years Solved Papers of
Civil Engineering : Paper-I
4. Beams ..............................................................................................................................271
5. Plastic Section ..............................................................................................................281
6. Plate Girder Load .........................................................................................................296
Unit-5 Design of Concrete and Masonry Structures .................................. 300-437
1. Beams ..............................................................................................................................300
2. Slabs .................................................................................................................................326
3. Columns .........................................................................................................................351
4. Footings ..........................................................................................................................362
5. Water Tanks and Stair Cases ....................................................................................373
6. Retaining Wall ..............................................................................................................394
7. Prestressed Concrete .................................................................................................413
Unit-6 Fluid Mechanics, Open Channel Flow and Hydraulic Machines .... 438-599
1. Fluid Statics ...................................................................................................................438
2. Fluid Properties and Pressure Measurement ...................................................449
3. Kinematics of Fluid Flow ..........................................................................................453
4. Fluid Dynamics ............................................................................................................461
5. Vortex Flow ...................................................................................................................478
6. Pipe Flow ........................................................................................................................484
7. Dimensional Analysis ................................................................................................504
8. Laminar Flow, Turbulent Flow & Boundary Layer Theory .............................519
9. Open Channel Flow ....................................................................................................542
10. Fluid Machinery ...........................................................................................................570
Unit-7 Geotechnical Engineering ................................................................ 600-718
1. Properties of Soil and Classification .....................................................................600
2. Capillary, Permeability and Effective Stress .......................................................617
3. Compressibility and Compaction .........................................................................626
4. Shear Strength of Soils ..............................................................................................647
5. Seepage Analysis and Stability of Slopes ...........................................................659
6. Earth Pressure and Retaining Wall ........................................................................663
7. Stress Distribution ......................................................................................................686
8. Shallow Foundation ...................................................................................................689
9. Pile Foundation ............................................................................................................701
10. Machine Foundation and Soil Exploration ........................................................716
