Quickly Installation Guide

Quickly Installation Guide

Web Configuration

Outdoor Wireless Br idge

1 Device Installation 2 Wireless Connection Topology

Passive PoE Adapter supports up to 60 meter (200 feet) Power over Ethernet deployment

Please prepare a long enough network cable to connect the POE adapter and CPE. Recommend to use a Category 5 (or above) shielded network cable with a ground wire.

Completed connection, push up to restore the CPE back cover

Place the CPE to the selected position and adjust the CPE front panel orientation to be approximately the same as the selected direction

Connect the PoE adapter’s LAN to PC, Router or Switch based on the network topology

Point to multiple point

IP Camera

IP Camera

IP Camera

IP Camera IP Camera

IP Camera

IP Camera

IP Camera ---- Wireless Bridge IP Camera --Switch --Wireless BridgeWireless Bridge ---- DVR ---- Monitoring PC Wireless Bridge--- DVR ---Monitoring PC

Wireless Bridge

Wireless Bridge Wireless Bridge

MonitoringPC

MonitoringPC

DVR

BA

Point to Point

SwitchDVR

In the wireless monitoring transmission, it is

recommended to use the above graphic method

for point-to-point or point-to-multi-point transmission.

The wireless bridge/outdoor CPE transmission angle

is oriented at 60 degrees. Please adjust the

equipment’s angle when building point-to-multi-point

transmission.

3.Bridge Ways

Operation:

1.Digital Display BridgeHere we are show how to the connection by press the Toggle switch button:

A: Mean Master APB: Mean Slave APWhen Toggle switch button on A side, mean this outdoor CPE is a master AP;When Toggle switch button on B side, mean this outdoor CPE is a slave AP

Master CPE Slave CPE

A B

BA

BA

BA

1.PC configuration if PC connect CPE by wirelessSet PC wireless network IP to 192.168.6.X （X: 2-250), same network segment as CPE, subnet mask: 255.255.255.0:

Check wireless connection Set wireless network

After IP address configuration, connect to CPE’s wireless SSID: Smart-Cpe_X, and input password (Default Password: 88888888)

equiring environment ：

Only applicable to areas below 2000 meters above sea level

Only applicable to non-tropical weather conditions

Wireless Network

Disable

Connect/Diconnect

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

Local Network Properties

Networking Sharing

Connect using:

Installl Uninstalll Propertie

DecriptionTransmission Control Protocol/Internet Protocol.The default widearea network protocol that provides communicationacross diverse interconnected networks.

This connection uses the following items:

Client for Microsoft NetworksQoS Packet SchedulerFile and Printer Sharing for Microsoft NetworksInternet Protocol Version6(TCP/IPv6)Internet Protocol Version4(TCP/IPv4)Link-Layer Topology Discovery Mapper I/O DriverLink-Layer Topology Discovery Responder

Realtek PCle GBE Family Controller

Configure...

OK Cancel OK

Advanced...

Cancel

Internet Protocol Version 4(TCP/IPv4) Properties

General

IP address:

Subnet mask:

Default gateway:

Obtain DNS server address automatically

Use the following DNS server addresses:

Preferred DNS server:

Alternate DNS server:

Obtain an IP address automatically

You can get IP settings assigned automatically if your network supportsthis capability.Otherwise,you need to ask your network administrator forthe appropriate IP settings.

Validate settings upon exit

192.168.6.10

255.255.255.0

. . .

. . .

. . .

Use the following IP address:

(Take the 5.8g wireless bridge as an example)

A B

BA

A B

A B

A B A B

A B

Smart-Cpe

The master AP can connect with 1~4 slave AP ; The Toggle switch button in A side in defaultThe default IP address of master AP is 192.168.6.1.

1st: Power on the Master AP and Slave AP;2nd: Push the Toggle switch button to A side on Master AP, Slave AP on B side.3rd: Short press the reset button on master AP and Slave AP to switch the digital display number to the same number.

Master CPE Slave CPE

A B A B

Press Reset on both side to the same number

4th: Wait a while, toggle the switch again to save the digital display number. A side on Master AP, Slave AP on B side, and the device will be automatically paired.After the pairing is successful, the IP address of the AP end (left) is 192.168.6.1, and the IP address of the client end(right) is delivered by the AP, as shown in the following figure.

RST RST

2.PC configuration if PC connect CPE wiredIf connect PC and CPE wired, Set PC local network IP to 192.168.6.X(X: 2-250), same network segment as CPE, subnet mask: 255.255.255.0:

Check the local network connection

Set fix IP address for PC

3. Login Web Configuration 4. Configure WirelessUse IE browser to access http://192.168.6.1, pop up the login page shown below,input the login password: admin, enter into the home page.

Login Web Interface

Homepage a. Use a laptop or mobile phone to test the wireless network Internet, click on the wireless network, select the wireless SSID, input the password to test whether PC or mobile phone can be online.

b. Check the wireless network connection status, signal strength and speed, transmission and data, click network connection details to see if the IP address and DNS server address are correctly obtained, confirm device is working properly .

5.Login WEB by Mobile Phone

1.Login CPE by Mobile phone(Password is admin)

Login

Login

Working Mode: Super WDS

click to setup location information

ON

channel9

Setup Wizard System Status

More FunctionsWiFi Setup

2.Configure Static IP address for mobile phone after connect with CPE by wireless

①Static IP address configuration on Android Mobile PhoneOpen settings in phone, turn on WLAN and find the SSID of the CPE, touch it for a long time until there is a menu, then choose”static IP” in the menu, set the mobile phone IP address as 192.168.6.X (X can not be 253 or 252), same network segment as CPE, subnet mask: 255.255.255.0, then gateway, subnet mask and domain .

4.Channel Table

Wireless Bridge Regional Channel Code Instructions

Trouble Shooting

Trouble

Packet Latency

Wrong password

Reason Solution

1.Wireless Interference2.Distance is too long,or there are some bar between them3.CPE’s angle in wrong direction, weak signal

1.Use Wi-Fi analysis to choose the best channel, or change to 5G CPE2.CPE should be in normal distance,and avoid bar3.Adjust the angle of CPE according to signal strength

1.Press reset button in 10 seconds to reset device, the default password is admin2.Re-input the password 3.Clear cookie,run arp -d to clear MAC table.

1.Forget password2.Input wrong password3.Too much cookie

1.Local IP is not in the same network segment of CPE2.IP is taken by other devices3.LAN Connection or Ethernet cable has problem4.Too much cookie, MAC address haven’t update

1.Ping 192.168.6.1 to see connection status2.Stop other devices or change to another IP3.Check LAN Connection and Ethernet cable4.Clear cookie,run arp -d to clear MAC address

Can not login WEB

1.PoE power supply is not working2.Some problem in CPE’s PoE port3.Ethernet cable is loose, RJ45 port is wrongPower current/voltage lower or wrong

1.Check if POE Adapter or POE switch work2.Check if POE port of CPE is OK3.Check if Ethernet cable is loose,if Ethernet cable plugged in to POE port4.Check if voltage is normal ,if socket has problem, if input voltage of POE adapter is normal

System LED light off

1.Packet Latency2.Ethernet cable circuit3.Network virus attack4.Too much access users

1.Adjust the distance, angle and channel to decrease latency2.Check if there is circuit in the network3.Check if port isolated to avoid network virus and broadcast storm4.Decrease the access users.

Low transmissionRate

1.Static electricity2.Running time too long3.Lightning stroke

1.Make CPE or POE adapter need ground connection2.Running time over 7 days, reboot it3.After lightning,device POE port broken or unstable, better to deploy lightning conductor .

Device always dead

Network Connection Details

Network Connection Details

Property

Connection-specific DN...DescriptionPhysical AddressDHCP EnabledIPv4 Subnet MakLease ObtainedLeae ExpiresIPv4 Default GatewayIPv4 DHCP ServerIPv4 DNS Servers

IPv4 WINS ServerNet BIO over Tcpip En...Link-local IPv6 AddresIPv6 Default Gateway

YesFe80：cb8:decO:56c1:94d%14

Qualcomm Atheros AR956x WirelesB8-86-87-3E-B5-3DYes192.168.6.217255.255.255.02018-7-28 9：57：232018-7-28 10：57：22192.168.6.1192.168.6.1114.114.114.114192.168.6.1

Value

Close Close

Wieless Network Status

General

Connection

IPv4 Connectivity:IPv6 Connectivity:Media State:SSID:Duration:Speed:Signal Quality:

InternetNo Internet access

EnabledSmart-Cpe

01:01:2172.2Mbps

Activity

Bytes:

Sent Received

Wireless PropertiesDetail...

Properties Disable DIagnoe

Local Network Properties

Networking Sharing

Connect using:

Installl Uninstalll Propertie

DecriptionTransmission Control Protocol/Internet Protocol.The default widearea network protocol that provides communicationacross diverse interconnected networks.

This connection uses the following items:

Client for Microsoft NetworksQoS Packet SchedulerFile and Printer Sharing for Microsoft NetworksInternet Protocol Version6(TCP/IPv6)Internet Protocol Version4(TCP/IPv4)Link-Layer Topology Discovery Mapper I/O DriverLink-Layer Topology Discovery Responder

Realtek PCle GBE Family Controller

Configure...

OK Cancel OK

Advanced...

Cancel

Internet Protocol Version 4(TCP/IPv4) Properties

General

IP address:

Subnet mask:

Default gateway:

Obtain DNS server address automatically

Use the following DNS server addresses:

Preferred DNS server:

Alternate DNS server:

Obtain an IP address automatically

You can get IP settings assigned automatically if your network supportsthis capability.Otherwise,you need to ask your network administrator forthe appropriate IP settings.

Validate settings upon exit

192.168.6.10

255.255.255.0

. . .

. . .

. . .

Use the following IP address:

Local Network

Disable

Status

Diagnose

Bridge Connections

Create Shortcut

Delete

Rename

Properties

WLAN

CONNECTED

Smart-Cpe_1

Smart-Cpe Saved

AVAILABLE NETWORKS

123456789

BDCOM-0000

BRCE 2.4G

BV_2_4G-200

BV_5_8G-200

400Mbps

None

fe80:528f:4cff:fef5:7bd6192.168.6.22

255.255.255.0

192.168.6.250

Canel OKSmart-Cpe_1 Network details

IP settings

> DHCP

Static

Canel OKSmart-Cpe_1 Network details

Gateway

PROXY

IP SETTINGS

192.168.6.250

None >

Static >

192.168.6.10

192.168.6.1

24

8.8.8.8

8.8.4.4

IP address

Gateway

prefix length

DNS 1

DNS 2

Modify network

Forget network

JZ Jennifer ZhouApple ID,iCloud,iTunes&App Store

Settings

Apple ID Suggestions

Airplane Mode

Wi-Fi

Bluetooth

Cellular

Personal Hotspot

VPN

Carrier

Smart-Cpe_1

On

Off

CHINA MOBILE

Search

JZ

Settings WI-FI

Wi-Fi

Smart-Cpe_1Unsecured Network

CHOOSE A NETWORK...

BDCOM_0000

BV_2_4G-200

BV_5_8G-200

HP-Print-35-LaserJet Pro MFP

M1 5G test

NIS-HomeAP-5G_519C

szjk5

Wireless 2.4G-11111

Wireless 5.8g-22222

Smart-Cpe

Back Configure IPv4

Automatic

Manual

BootP

MANUAL IP

IP Address

Subnet Mask

Router

192.168.6.10

255.255.255.0

192.168.6.1

1 2 3 4 5 6 7 8 9 0

ABC

#+= . , ,? !

space return

②Static IP address configuration on IOS Mobile PhoneOpen settings and choose Wi-Fi, connect with CPE, click exclamation mark , manual to set IP address 192.168.6.X (X can not be 253 or 252) and subnet for mobile phone, note: mobile phone’s IP address should be same network segment as CPE.

Android system setup steps

ISO system setup steps

In this page, show the AP’s five working mode: Router, Universal Repeater, WISP, AP and Repeater.

Router Mode: Router function, WAN port connection modem (ADSL cat or fiber cat) dial-up Internet or WAN port dynamic, static IP address mode.

Universal Repeater Mode：Enables wireless repeater and forwarding without matching with theupper device.

WISP Mode：Wireless WAN client wirelessly connects to the Operator's wireless base station for local LAN network sharing.

AP Mode：In this mode, NAT, DHCP, firewall and all WAN-related functions are turned off. All wireless interfaces and wired interfaces are bridged together, without distinguishing between LAN and WAN.

Repeater Mode：In this mode, it usually refers to the point to point situation. The wireless CPE at both ends of the bridge only communicates with the wireless CPE at the other end. The device can add the MAC address of the other party by scanning the available network, and the encryption mode of both devices must be consistent.

Please confirm the operation mode first before configuration starting.

192.168.6.1

Configuration method: According to the various modes quick setup wizard shown in theabove figure, set the parameters and options required by the user, click Next, and completethe setting of each operation mode.