1-3w power led - gseo · 1-3w power led gp -e series led ... gp-e series led datasheet ... 1...

GP-E series LED Datasheet (02/25/10) – V02 1

1-3W Power LED

GP-E Series LED

Introduction

GSEO GP-E series LED is an ultra-compact, surface mount, high power LED that delivers elevated

standards for light output, flux density and manufacturability. Offering better flux density, lumens per

package and power handling capabilities, GP-E LED enable you:

■ Create more useable light and higher flux density

■ Optimize applications to reduce size and cost

■ Tightly pack the LEDs for color mixing applications

■ Engineer more robust applications

■ Utilize standard FR4 PCB technology

■ Simplify manufacturing through the use of surface mount technology.

Typical application ■ Reading lights (car, bus, aircraft)

■ Portable (flashlight, bicycle) ■ LCD Backlights ■ General lighting ■ Indoor/Outdoor Commercial and Residential Architectural ■ Contour lights ■ Traffic signaling/Beacons/ Rail crossing and Wayside ■ Fiber optic alternative/ Decorative/Entertainment ■ Architectural lighting


Table of Contents

Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Average Lumen Maintenance Characteristics . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . 3

Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Visual Appearance of GP-E series LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Flux Characteristics for GP-E series LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Reflow Soldering Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pad Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Wavelength Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Typical Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Typical Relative Luminous Flux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Current Derating Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Typical Radiation Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Emitter Pocket Tape Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Emitter Reel Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Product Binning and Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Cool-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Neutral-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Warm-White Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Color Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27


Product Nomenclature

GP-E series LED is tested and binned at 350mA.

The part number designation is explained as follows:

GS - A B C D E

Where:

A — designates Power LED package

B — designates package platform (A for Alumina Ceramic substrate)

C — designates view angle (A for 140 degrees, B for 120 degrees)

D — designates color variant (C for Cool-White, W for Warm-White, N for Neutral-White, B for Blue, G for Green,

R for Red, Y for Yellow)

E — designates chip classification

Average Lumen Maintenance Characteristics

Lifetime for solid-state lighting devices (LEDs) is typically defined in terms of lumen maintenance—the percentage of

initial light output remaining after a specified period of time.

GSEO LED BU projects that cool-white, neutral-white, warm-white, green, cyan, and blue. GP-E series LED products

will deliver, on average, 70% lumen maintenance (B50, L70) at 50,000 hours of operation at a forward current of 350

mA. This projection is based on constant current operation with junction temperature maintained at or below 135°C.

GSEO LED BU projects that red, red-orange and amber. GP-E series LED products will deliver, on average, 70%

lumen maintenance (B50, L70) at 50,000 hours of operation at a forward current of 350 mA. This projection is based

on constant current operation with junction temperature maintained at or below 110°C.

This performance is based on independent test data, GSEO LED BU historical data from tests run on similar material

systems, and internal GP-E series LED reliability testing. Observation of design limits included in this data sheet is

required in order to achieve this projected lumen maintenance.

Environmental Compliance

GSEO LED BU is committed to providing environmentally friendly products to the solid-state lighting market. GP-E

series LED is compliant to the European Union directives on the restriction of hazardous substances in electronic

equipment, namely the RoHS directive. GSEO LED BU will not intentionally add the following restricted materials to

the GP-E series LED: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or

polybrominated diphenyl ethers (PBDE).

Visual Appearance of GP-E series LED

All lighted GP-E series LED product will provide comparable Lambertian beam performance, suitable for use with

commercially available optical systems. Without power, LED die within different reels may appear visually different.


Flux Characteristics for GP-E series LED—Thermal Pad Temperature = 25°C

Table 1.

Performance at Test Current Typical Performance at

Indicated Current

Color Part Number Typical Luminous

Flux (lm) Drive Current (mA)

Typical Luminous

Flux (lm)

Drive Current

(mA)

GS-PFBCR 92 350 156.4 700

Cool-White GS-PFBCE

GS-PFBCT

90

87.3

350

350

153

148

700

700

GS-PFBNR 83 350 141 700

Neutral-White GS-PFBNE

GS-PFBNT

81

75

350

350

137.7

127.5

700

700

GS-PFBWR 78 350 132.6 700

Warm-White GS-PFBWE

GS-PFBWT

75.2

70.6

350

350

127.8

120

700

700

GS-PFAGE 75 350 127 700 Green

GS-PFAGG 73 350 124 700

GS-PFABR 15 350 25 700

GS-PFABE 13 350 22 700 Blue

GS-PFABT 13 350 22 700

GS-PFARE 32 350 54 500 Red

GS-PFARH 35 350 60 500

GS-PFARE 28 350 47 500 Amber

GS-PFARH 30 350 51 500

Notes for Table 1: 1. Minimum luminous flux or radiometric power performance guaranteed within published operating

conditions. GSEO LED BU maintains a tolerance of ± 10% on flux measurements. 2. Typical luminous flux performance when device is operated within published operating conditions. 3. GP-E series LED products with even higher luminous flux and radiometric power levels will become

available in the future.


Optical Characteristics

GP-E series LED at Test Current[1]

Thermal Pad Temperature = 25°C

Table 2.

Notes for Table 2:

1. Test current is 350 mA for all GS-PFXXX products.

2. Dominant wavelength is derived from the CIE 1931 Chromaticity diagram and represents the perceived

color. GSEO LED BU maintains a tolerance of ± 1 nm for dominant wavelength measurements.

3. CCT ±5% tester tolerance.

4. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value.

5. Typical CRI (Color Rendering Index) for Cool-White is 70, Neutral-White is 75 and Warm-White is 80.

6. All white, green, cyan, and blue products are built with Indium Gallium Nitride (InGaN).

7. All red, red-orange, and amber are built with Aluminum Indium Gallium Phosphide (AlInGaP).

8. Cool-White, Neutral-White, Warm-White, and Blue power light sources represented here are IEC825 class 2

for eye safety.

Dominant Wavelength [2]λD

or Color Temperature [3]

CCT

Color Min. Typ. Max.

Typical

Temperature

Coefficient of

Dominant

Wavelength

(nm/℃)

∆λD/ ∆TJ

Typical

Viewing

Angle [4]

(degrees)

2θ 1/2

Cool-White 4500K 6500K 10,000 K N/A 120

Neutral-White 3500K 4100 K 4500 K N/A 120

Warm-White 2670K 3100 K 3500 K N/A 120

Green 520nm 530 nm 550 nm 0.05 140

Blue 460 nm 470 nm 490 nm 0.05 140

Red 620.5 nm 627 nm 645 nm 0.05 140

Amber 584.5 nm 590 nm 597 nm 0.10 140


Electrical Characteristics

Electrical Characteristics at 350mA for GP-E series LED,

Part Numbers GS-PDXXX, Thermal Pad Temperature = 25ºC Table 3

Notes for Table 3:

1. GSEO LED BU maintains a tolerance of ±0.1 V on forward voltage measurements.

Color

Forward Voltage Vf[1]

(V)

Min. Typ. Max.

Typical Thermal Resistance Junction to

Thermal Pad

(oC/W)

RJC

Cool-White 3.00 3.60 4.10 10

Neutral-White 3.00 3.60 4.10 10

Warm-White 3.00 3.60 4.10 10

Green 3.00 3.60 4.10 10

Blue 3.00 3.60 4.10 10

Red - - 3.00 12

Amber - - 3.00 12


Absolute Maximum Ratings

Table 4.

Parameter Cool-White/Neutral-White/Warm-White Red/Amber

/Green/Blue

DC Forward Current (mA) 400 350

Peak Pulesd Forward Current (mA) 750 500

Average Forward Current (mA) 350 250

ESD Sensitivity <8000V Human Body Model (HBM) <8000V Human Body Model (HBM)

Class 2 JESD22A114B Class 2 JESD22A114B

<400V Machine Model (MM) <400V Machine Model (MM)

Class 2 JESD22A115B Class 2 JESD22A115B

LED Junction Temperature[1] 150°C 115°C

Operating Case Temperature at 350 mA -40°C ~ 135°C -40°C ~ 135°C

Storage Temperature -40°C ~ 135°C -40°C ~ 135°C

Soldering Temperature JEDEC 020c 260°C JEDEC 020c 260°C

Allowable Reflow Cycles 3 3

Autoclave Conditions 121°C at 2 ATM

100% Relative Humidity for 96 Hours Maximum

Reverse Voltage (Vr) See Note 2 See Note 2

Notes for Table 4:

1. Proper current derating must be observed to maintain junction temperature below the maximum.

2. GP-E series LEDs are not designed to be driven in reverse bias.

JEDEC Moisture Sensitivity Table 5.

Level Floor Life

Time Conditions

Soak Requirements

Standard

Time Conditions (hours)

1 unlimited ≦30℃/

85％RH

168 85℃ / 85％

+5/0 RH


Reflow Soldering Characteristics

Table 6.

Profile Feature Lead Free Assembly

Average RampUP Rate (Tsmaxto Tp) 3°C / second max

Preheat Temperature Min(Tsmin) 150°C

Preheat Temperature Max (Tsmax) 200°C

Preheat Time (tsminto tsmax) 60-180 seconds

Time Maintained Above Temperature (TL) 217°C

Time Maintained Above Time (tL) 60-150 seconds

Peak / Classification Temperature (TP) 260°C

Time Within 5°C of Actual Peak Temperature (tP) 20-40 seconds

Ramp-Down Rate 6°C / second max

Time 25°C to Peak Temperature 8 minutes max

Notes for Table 6:

1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package

body.


Mechanical Dimensions

Figure 1. Package Outline Drawing

Notes for Figure 1:

1. Do not handle the device by the lens-care must be taken to avoid damage to the lens or the interior

of the device that can be damaged by excessive force to the lens.

2. Drawings not to scale.

3. All dimensions are in millimeters. Pad Configuration

Figure 2. Pad Configuration.

Note for Figure 2:

1. The Thermal Pad is electrically isolated from the Anode and Cathode contact pads.


Wavelength Characteristics Green, Blue, Red and Amber

at Test Current, Thermal Pad Temperature, TJ= 25°C

0

20

40

60

80

100

350 400 450 500 550 600 650 700 750

Wavelength (nm)

Rela

tive

Spect

ral Pow

er

Dis

trib

ution (

%)

Figure 3. Relative intensity vs. wavelength

Cool-White at Test Current Thermal Pad Temperature = 25°C

Figure 4a. Cool-White color spectrum of typical CCT part, integrated measurement.

0

20

40

60

80

100

350 400 450 500 550 600 650 700 750 800

Wavelength (nm)

Rela

tive

Spect

ral Pow

er

Dis

trib

ution (

%)


Neutral-White at Test Current


400 450 500 550 600 650 700 750 800

Wavelength (nm)

Spect

ral Pow

er

Dis

trib

ution

Figure 4b. Neutral-White color spectrum of typical CCT part, integrated measurement.

Warm-White at Test Current Thermal Pad Temperature = 25°C

400 450 500 550 600 650 700 750 800

Wavelength (nm)

Spect

ral Pow

er

Dis

trib

ution

Figure 4c. Warm-White color spectrum of typical CCT part, integrated measurement.


Typical Forward Current Characteristics

Cool-White, Neutral-White, Warm-White, Green and Blue Thermal Pad Temperature = 25°C

0

100

200

300

400

500

600

700

800

2 2.5 3 3.5 4 4.5

Forward Voltage(Vf)-volts

Forw

ard

Curr

wnt(

If)-

mA SiC base chip

Sapphire base chip

Figure 5. Forward current vs. forward voltage for all White, Green and Blue.

Red and Amber, Thermal Pad Temperature = 25°C

0

100

200

300

400

500

600

1 1.5 2 2.5 3

Forward Voltage(Vf)-volts

Forw

ard

Curr

wnt(

If)-

mA

Figure 6. Forward current vs. forward voltage for Red and Amber.


Typical Relative Luminous Flux

Typical Relative Luminous Flux vs. Forward Current for Cool-White, Neutral-White, Warm-White, Green and Blue,


Figure 7. Relative luminous flux vs. forward current for all White, Green and Blue, test current 350mA.

Typical Relative Luminous Flux vs. Forward Current for Red and Amber, Thermal Pad Temperature = 25°C

Figure 8. Relative luminous flux vs. forward current for Red and Amber, test current 350mA.

0%

20%

40%

60%

80%

100%

120%

140%

0 100 200 300 400 500 600

Forward Current (mA)

Norm

aliz

ed L

um

inous

Flu

x

0%

20%

40%

60%

80%

100%

120%

140%

160%

180%

0 100 200 300 400 500 600 700 800

Forward Current (mA)

Norm

aliz

ed L

um

inous

Flu

x


Current Derating Curves

Current Derating Curve for 350 mA drive current for Cool-White, Neutral-White, Warm-White, Green and Blue

0

50

100

150

200

250

300

350

400

0 25 50 75 100 125 150 175

TA-Ambient Temperature ℃

IF-F

orw

ard

Curr

ent

mA

10℃/W

Figure 9. Maximum forward current vs. ambient temperature, base on Tjmax=150°C

Current Derating Curve for 350 mA drive current for Red and Amber

0

50

100

150

200

250

300

350

400

0 25 50 75 100 125 150

TA-Ambient Temperature ℃

IF-F

orw

ard

Curr

ent

mA

12℃/W

Figure 10. Maximum forward current vs. ambient temperature, base on Tjmax=115°C


Typical Radiation Patterns

Typical Representative Spatial Radiation Pattern

for Cool-White, Neutral-White and Warm-White Lambertian

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

-90 -75 -60 -45 -30 -15 0 15 30 45 60 75 90

Angular Displacement deg

Rela

tive

lnte

nsi

ty %

Figure 11. Typical representative spatial radiation pattern for all White lambertian.

Typical Polar Radiation Pattern for White Lambertian

Figure 12. Typical polar radiation pattern for all White lambertian


Typical Representative Spatial Radiation Pattern for Green and Blue Lambertian

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90


Rela

tive

lnte

nsi

ty %

Figure 13. Typical representative spatial radiation pattern for Green and Blue lambertian.

Typical Polar Radiation Pattern for Green and Blue Lambertian

Figure 14. Typical polar radiation pattern for Green and Blue lambertian


Typical Representative Spatial Radiation Pattern

for Red and Amber Lambertian

0%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90


Rela

tive

lnte

nsi

ty %

Figure 15. Typical representative spatial radiation pattern for Red and Amber lambertian.

Typical Polar Radiation Pattern for Red and Amber Lambertian

Figure 16. Typical polar radiation pattern for Red and Amber lambertian


Emitter Pocket Tape Packaging Unit: mm


Emitter Reel Packaging Unit: mm


Product Binning and Labeling

Purpose of Product Binning In the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. For this reason, GSEO LED BU bins the LED components for luminous flux, color and forward voltage (VF).

Decoding Product Bin Labeling GP-E series LED are labeled using four digit alphanumeric code (CAT code) depicting the bin values for LED packaged on a single reel. All LEDs packaged within a reel are of the same 3 variable bin combination. Using these codes, it is possible to determine optimum mixing and matching of products for consistency in a given application.

Format of Labeling for Emitters Reels of Green, Cyan, Blue, Red, Red-Orange and Amber LEDs are labeled with a four digit alphanumeric CAT

code following the format below.

ABCD

A = Flux bin (H, J, K, L etc.)

B = Color bin (1, 2, 3, etc.)

C = Wavelength bin (1, 2, 3, etc.)

D = VFbin (D, E, F, G etc.)

Reels of Cool-White, Neutral-White and Warm-White Emitters are labeled with a four digit alphanumeric CAT code following the format below.

ABCD

A = Flux bin (J, H, J, K etc.)

B and C = Color bin (W0, U0, V0 etc.)

C = VFbin (D, E, F, G etc.)


Luminous Flux Bins

Table 7 lists the standard photometric luminous flux bins for GP-E series LED (tested and binned at 350mA).

Although several bins are outlined, product availability in a particular bin varies by production run and by product

performance. Not all bins are available in all colors.

Table 7.

Flux Bins - All Colors

Minimum Photometric Flux Maximum Photometric Flux

Bin Code (lm) (lm)

A 8 12

B 12 16

C 16 20

D 20 24

E 24 30

F 28 32

G 32 36

H 36 40

I 40 45

J 45 50

K 50 60

L 60 70

M 70 80

N 80 90

P 90 100

Q 100 120

R 120 140

S 140 160

T 160 180

U 180 200

V 200 220

W 220 240

X 240 260

y 260 280

Z 280 300


Cool-White Bin Structure

WQWQYO

YA

XM

XN

X0

XP

WM

WN

W0

WP

VM

VN

V0

VP

UM

UN

U0

UP

0.25

0.27

0.29

0.31

0.33

0.35

0.37

0.39

0.41

0.25 0.27 0.29 0.31 0.33 0.35 0.37 0.39x

y

4500K

5000K

5630K

6300K

7000K

blackbody locus

10000K

Figure 17. Cool-White bin structure


Cool-White Bin Coordinates

Cool-White GP-E series LED are tested and binned by x,y coordinates.

19 Color Bins, CCT Range 10,000K to 4,500K

Table 8.

Cool-White Bin Coordinates

Typical CCT Typical CCT

Bin Code X Y (K) Bin Code X Y (K)

0.274238 0.300667 0.318606 0.310201

Y0 0.303051 0.332708 8000 WQ 0.329393 0.320211 6000

0.307553 0.310778 0.329544 0.310495

0.282968 0.283772 0.319597 0.301303

0.282968 0.283772 0.328636 0.368952

YA 0.307553 0.310778 8000 VM 0.348147 0.385629 5300

0.311163 0.293192 0.346904 0.371742

0.289922 0.270316 0.328823 0.356917

0.301093 0.342244 0.328823 0.356917

XM 0.313617 0.354992 6700 VN 0.346904 0.371742 5300

0.314792 0.344438 ` 0.345781 0.359190

0.303051 0.332708 0.329006 0.345092

0.303051 0.332708 0.329006 0.345092

XN 0.314792 0.344438 6700 VO 0.345781 0.359190 5300

0.316042 0.333222 0.344443 0.344232

0.305170 0.322386 0.329220 0.331331

0.305170 0.322386 0.329220 0.331331

XO 0.316042 0.333222 6700 VP 0.343352 0.344232 5300

0.317466 0.320438 0.329393 0.332034

0.307553 0.310778 0.348147 0.320211

0.307553 0.310778 0.348147 0.385629

XP 0.317466 0.320438 6700 UM 0.367294 0.400290 4750

0.319597 0.301303 0.364212 0.382878

0.311163 0.293192 0.346904 0.371742

0.313617 0.354992 0.346904 0.371742

WM 0.328636 0.368952 6000 UN 0.364212 0.382878 4750

0.328823 0.356917 0.362219 0.371616

0.314792 0.344438 0.345781 0.359190

0.314792 0.344438 0.345781 0.359190

WN 0.328823 0.356917 6000 UO 0.362219 0.371616 4750

0.329006 0.345092 0.359401 0.355699

0.316042 0.333222 0.344443 0.344232

0.316042 0.333222 0.344443 0.344232

WO 0.329006 0.345092 6000 UP 0.359401 0.355699 4750

0.329220 0.331331 0.357079 0.342581

0.317466 0.320438 0.343352 0.332034

0.317466 0.320438

WP 0.329220 0.331331 6000

0.329393 0.320211

0.318606 0.310201

.

Note for Table 8:

1. GP-E series LED maintains a tester tolerance of ± 0.005 on x, y color coordinates.


Neutral-White Bin Structure

TM

TN

T0

TP

SM

SN

S0

SP

RM

RN

R0

RP

0.32

0.34

0.36

0.38

0.4

0.42

0.44

0.33 0.35 0.37 0.39 0.41 0.43x

y

3500K

3800K

blackbody locus

4100K

4500K

Figure 18: Neutral-White Bin Structure

Neutral-White GP-E series LED are tested and binned by x,y coordinates. 12 Color Bins, CCT Range 4,500K to 3,500K

Table 9.

Neutral-White Bin Coordinates



0.367294 0.400290 0.378624 0.382458

TM 0.385953 0.412995 4300 SO 0.392368 0.3990932 3950

0.381106 0.393747 0.387071 0.373899

0.364212 0.382878 0.374075 0.365822

0.364212 0.382878 0.374075 0.365822

TN 0.381106 0.393747 4300 SP 0.387071 0.373899 3950

0.378264 0.382458 0.382598 0.359515

0.362219 0.371616 0.370582 0.351953

0.362219 0.371616 0.402270 0.422776

TO 0.378264 0.382458 4300 RM 0.420940 0.432618 3650

0.374075 0.365822 ` 0.414776 0.416097

0.359401 0.355699 0.396279 0.403508

0.359401 0.355699 0.396279 0.403508

TP 0.374075 0.365822 4300 RN 0.414776 0.416097 3650

0.370582 0.351953 0.408593 0.399525

0.357079 0.342581 0.392368 0.390932

0.385953 0.412995 0.392368 0.390932

SM 0.402270 0.422776 3950 RO 0.408593 0.399525 3650

0.396279 0.403508 0.402113 0.382156

0.381106 0.393747 0.387071 0.373899

0.381106 0.393747 0.387071 0.373899

SN 0.396279 0.403508 3950 RP 0.402113 0.382156 3650

0.392368 0.390932 0.396564 0.367284

0.378264 0.382458 0.382598 0.359515

Note for Table 9:

1. GSEO LED BU maintains a tester tolerance of ± 0.005 on x, y color coordinates.


Warm-White Bin structure

QM

QN

Q0

QP

PM

PN

P0

PP

NM

NN

N0

NP

MM

MN

M0

MP

0.35

0.37

0.39

0.41

0.43

0.45

0.47

0.38 0.4 0.42 0.44 0.46 0.48 0.5x

y

blackbody locus

2670K2850K3050K

3500K3250K

Figure 19: Warm-White Bin Structure.

Warm-White GP-E series LED are tested and binned by x,y coordinates. 16 Color Bins, CCT Range 3,500K to 2,670K

Table 10.

Warm-White Bin Coordinates



0.420940 0.432618 0.453820 0.445980

QM 0.438458 0.440399 3375 NM 0.470507 0.450832 2950

0.431186 0.423386 0.461404 0.433334

0.414776 0.416097 0.445639 0.428680

0.414776 0.416097 0.445639 0.428680

QN 0.431186 0.423386 3375 NN 0.461404 0.43334 2950

0.423956 0.406472 0.452512 0.416241

0.408593 0.399525 0.437578 0.411632

0.408593 0.399525 0.437578 0.411632

QO 0.423956 0.406472 3375 NO 0.452512 0.416241 2950

0.416487 0.389001 ` 0.443600 0.399111

0.402113 0.382156 0.429373 0.394281

0.402113 0.382156 0.429373 0.394281

QP 0.416487 0.389001 3375 NP 0.443600 0.399111 2950

0.409996 0.373814 0.435591 0.383714

0.396564 0.367284 0.422124 0.378952

0.438458 0.440399 0.470507 0.450832

PM 0.453820 0.445980 3150 MM 0.486648 0.454191 2760

0.445639 0.428680 0.476733 0.436634

0.431186 0.423386 0.461404 0.433334

0.431186 0.423386 0.461404 0.433334

PN 0.445639 0.428680 3150 MN 0.476733 0.436634 2760

0.437578 0.411632 0.467132 0.419632

0.423956 0.406472 0.452512 0.416241

0.423956 0.406472 0.452512 0.416241

PO 0.437578 0.411632 3150 MO 0.467132 0.419632 2760

0.429373 0.394281 0.457663 0.402866

0.416487 0.389001 0.443600 0.399111

0.416487 0.389001 0.443600 0.399111

PP 0.429373 0.394281 3150 MP 0.457663 0.402866 2760

0.422124 0.378952 0.448994 0.387515

0.409996 0.373814 0.435591 0.383714


Color Bins

All GP-E series LED are tested and binned for dominant wavelength.

Dominant Wavelength Bin Structure for Green Table11.

Bin Code

Minimum Dominant Wavelength

(nm)

Maximum Dominant Wavelength

(nm)

31 520 525

32 525 530

33 530 535

34 535 540

35 540 545

36 545 550

37 500 510

38 510 520

Dominant Wavelength Bin Structure for Blue Table12.

Bin Code


(nm)


(nm)

41 450 455

42 455 460

43 460 465

44 465 470

45 470 475

46 475 480

47 480 485

48 485 490

Dominant Wavelength Bin Structure for Red

Dominant Wavelength Bin Structure for Amber Table14.

Bin Code


(nm)


(nm)

51 584.5 587.0

52 587.0 589.5

53 589.5 592.0

54 592.0 594.5

55 594.5 597.0

Table13.

Bin Code


(nm)


(nm)

11 620.5 631

12 631 645


Forward Voltage Bins

Table 15 lists minimum and maximum VF bin values per emitter. Although several bins are outlined, product availability in

a particular bin varies by production run and by product performance.

Table15.

VF Bins

Bin Code

Minimum Forward Voltage

(V)

Maximum Forward Voltage

(V)

A 2.07 2.31

B 2.31 2.55

C 2.55 3.79

D 3.79 3.03

E 3.03 3.27

F 3.27 3.51

G 3.51 3.75

H 3.75 3.99

2 2 2.5

3 2.5 3

4 3 3.6

5 3.6 4.2

6 4.2 5

1-3w power led - gseo · 1-3w power led gp -e series led ... gp-e series led datasheet ... 1...

Documents