05-22-003 mt clutch release bearing installation

M/T - Clutch Release Bearing Installation No: TSB-05-22-003 DATE: October 19, 2005 SUBJECT: CLUTCH RELEASE BEARING INSTALLATION MODEL: See below PURPOSE The manual transmission on affected vehicles has a pull-type clutch. When removing or installing the transmission, use care to prevent dislodging the clutch cover (pressure plate) wire ring due to interference with the input shaft and/or clutch housing. If the wire ring is dislodged, it could come off completely during driving, causing the clutch to become inoperative. AFFECTED VEHICLES 2003-on Lancer Evolution models 2001-2005 Eclipse and Eclipse Spyder models equipped with V6 engine PROCEDURE

Upload: api-3855859

Post on 10-Apr-2015

203 views

Category:

Documents

7 download

Report

Download

Embed Size (px):

TRANSCRIPT

M/T - Clutch Release Bearing Installation

No: TSB-05-22-003

DATE: October 19, 2005

SUBJECT: CLUTCH RELEASE BEARING

INSTALLATION MODEL: See below

PURPOSE The manual transmission on affected vehicles has a pull-type clutch. When removing or installing the transmission, use care to prevent dislodging the clutch cover (pressure plate) wire ring due to interference with the input shaft and/or clutch housing. If the wire ring is dislodged, it could come off completely during driving, causing the clutch to become inoperative.AFFECTED VEHICLES 2003-on Lancer Evolution models2001-2005 Eclipse and Eclipse Spyder models equipped with V6 engine

PROCEDURE

Page 2: 05-22-003 MT Clutch Release Bearing Installation

Illustration of Clutch and Input Shaft.

The information contained in this bulletin is subject to change. For latest version of this document go to the Mitsubishi Dealer Link, MEDIC, or the Mitsubishi Service Information website.

SOLVING WINDMILLING PROBLEMS ON BELT ACHE FAN SYSTEMS€¦ · The device was a one-way clutch system comprised of a shaft bushing, clutch adaptor, clutch housing, clutch bearing with

0-10 INCH/THRUST BEARING 0-11 INCH/THRUST BEARING · PDF file0-11 inch/thrust bearing 0-14 inch/thrust bb ... 12bc04s3 nachi ball bearing clutch pilot 12bc04s3 dd pfi-usa precision

OUTBOARD - marcs-marine.com · FOrWArD gEAr INNEr BEArINg Replaces: 91057-ZW1-003 18-1158 CArrIEr BEArINg Replaces: 91053-ZW1-003 18-1156 FOrWArD gEAr BEArINg Replaces: 91051-ZW1-003

0-10 INCH/THRUST BEARING 0-11 INCH/THRUST BEARING · PDF file12bc04s3 nachi ball bearing clutch pilot 12bc04s3 dd pfi-usa precision ball bearing 2 seals 1300 self aligning ball bearing

CLUTCHES & COMPONENTS - FleetPride · need a self-adjusting clutch, manual clutch, flywheel, clutch brakes, pilot bearing or alignment tool, OTR has what you need to get the job done

IP · bearing, center link, clutch disc, clutch masterassembly, clutch operating assembly, coil spring, fan belt, oil seal, shaft kit" underClass 07, "pressure plate" underClass 09,

CLUTCH...Clutch release bearing Type Free travel Clutch release cylinder Single dry disc type 240 x 160 (9.45 x 6.30) Diaphragm spring, strap drive type Self-centering type 0 (Zero)

PARTS MANUAL - Kattrak · 2016. 10. 19. · 003 115.08000.00 washer din434 1 004 309.17012.00 bearing din625 1 005 15.02011.01 disk clutch 1 006 10.00201.00 pressure plate 1 007 105.06000.66

2015šаталог KROSS 2015.pdfTiming belt Drive belt Timing belt kits Clutch disc Clutch cover Clutch release bearing Clutch kits Clutch cylinders Rails Starters Alternators Alternator

TSUBAKI CAM CLUTCH / FREEWHEELS · PDF filetsubaki cam clutch design features 5 tsubaki ball bearing cam clutch / freewheels tsubaki cam clutch / freewheels without bearing support

Tractors - hydrauliikkapumppu.fi · Clutch Disc Valmet 8050/81-84/85/8750 14” Valmet Valtra ** 51414 is Cover ** 22 Spl Clutch Release Bearing Valmet 8050, 81-84, 85, 8750 Clutch

Power transmission-Belt drives and bearing selection TUTOR ... · PDF filePOWER TRANSMISSION-BELT DRIVES AND BEARING SELECTION TUTOR: ... expanding-shoe centrifugal clutch ... Advantages