04-bsc6900v900r011 go data configuration issue2.0-20100506-b

7/18/2019 04-BSC6900V900R011 GO Data Configuration ISSUE2.0-20100506-B

1/61

www.huawei.com

Security Level: Internal Use

HUAWEI TECHNOLOGIES Co., Ltd. HUAWEI Confidential

Dual-mode BSC6900

Data ConfigurationGSM Only

TSD wireless product service department-GBSS

ISSUE2.0

2010-05


2/61

HUAWEI TECHNOLOGIES Co., Ltd. HUAWEI Confidential Page 2

This slide describes the process of creating the script of the

BSC6900 initial configuration depend on the WebLMT.


3/61


Be familiar with the data configuration steps

Know the method of data effective

Know how to create a new CELL and a new BTS quickly


4/61


BSC6900 Intial Configuration Guide(V900R011C00)

BSC6900 Commissioning Guide(V900R011C00)

BSC6900 MML Command Reference (V900R011C00)

Typical Configuration Scripts (in Intial Configuration Guide)


5/61


Chapter 1 Summarize of Data Configuration

Chapter 2 Data Configuration


6/61


The Evolution of Data Configuration Client

We can use GUI and MML to complete the data configuration for BSC6000,

one for Graphic User Interface, another for Man Machine Language which canrun batch script.

For BSC6900, we use WebLMT and CME to do the data configuration. No

need to install the server software on your PC, and we can login by Web

anywhere to do the data configuration by MML command.

GUI LMT MML LMT

M2000 CME

Web LMT

M2000 CME

BSC6000 BSC6900


7/61


WebLMT Login

Enter the external virtual IP address of the OMU in the address bar on the IE.

Press Enteron the keyboard, or click Gonext to the address bar to display thelogin window of the BSC6900.

Enter the Name, Password, and Verify Code. Select the User Type. You can

select Local Useror EMS. If the verify code is illegible, click Change the verify

codefor a new code.


8/61


Data Configuration Interface of MML

Navigation

Tree

Command Display

Running

Failed

Running

Successful

Input

Command


9/61


Run Batch Interface


10/61


Data Configuration Modes

Principle of Effective Mode Configuration

The process of effective mode configuration is as follows: The BSC6900 is switched to effective mode.

The configuration console (LMT or M2000) sends MML commands to the configuration

management module of the OMU.

The configuration management module of the OMU sends the configuration data to the

database of the related host board and writes the data to the OMU database.

Realize

We can use SET CFGDATAINEFFECTIVEto switch between effective and ineffective

mode.

One command just for one subrack.

This mode used in modifying data dynamic.


11/61


Data Configuration Modes

Principle of Ineffective Mode Configuration

The process of ineffective mode configuration is as follows: The BSC6900 is switched to ineffective mode.

The configuration console (LMT or M2000) sends MML commands to the configuration

management module of the OMU.

The configuration management module sends only the configuration data to the OMU database.

When a subrack or the BSC6900 is reset, the OMU formats the configuration data in the

database into a .dat file, loads the file onto the related host boards, and then activates the

configuration data.

Realize

We can use SET CFGDATAINEFFECTIVEto switch between effective and ineffective mode.

One command just for one subrack.

This mode used in Initial data Configuration .


12/61


Data Configuration Take Effect

Begin

Generating the Data

File for the Loading

Setting the

Loading Mode

Resetting the

BSC6900 Boards

Checking the Consistency

of the Data and the Version

Finish

Set the subrack as

ineffective mode

SET CFGDATAINEFFECTIVE

Initialize the BSC6900

configuration DataRST DATA

Run MML batch RUN BATCHFILE

Format the data

filesFMT DATA

Set the subrack

work mode

SET LODCTRL

Reset subrack RST SUBRACK

Check the

consistencyACT CRC

Set the subrack as

effective modeSET CFGDATAEFFECTIVE

Updating the OMU

Database


13/61


Change in MML Data configuration of BSC6900

Equipment and logical data are separated in site and cell data configuration.

Equipment data, logical data, bind.

SRAN sites3900 sites of 2G and 3G unify to SRAN sites3900 sites with 9.0software version Types of sites supported SRANMODE:

BTS3900,BTS3900A,DBS3900,BTS3036,BTS3036A,DBS3036A,BTS3900L

Select SRANMODE when add bts;

Select actual cabinets when add bts cabinets, such as APM30, RFC etc.

Designate the cabinet, subrack and slot information when add RXU board;

Designate the cabinet, subrack and slot information of main control board which transmission

is connected to in BTS when add bts connect.

The data of the site unsupported SRANMODE and cannot be changed to the site supported

SRANMODE by MML data configuration.

Others

OPC is binded to cells, not to the BSC subrack; Clock source is configured for interface boards, not for BSC subrack;

Signaling links set is need to add;

GSM CN node is need to configure.


14/61


PC OMU

Functions

The PC OMU is auxiliary software developed on the basis of the OMU software of

Windows version. The PC OMU enables Huawei engineers to operate the OMU

software on their PCs.

Data configuration through MML commands

Verify the data configuration through the license file

Panel display on the LMT (optional)

Methods of Obtaining the Software and Documents

Softwarehttp://support.huawei.comSoftware -> Version Software -> Wireless Product Line -> Single RAN -> MBSC -> BSC6900 ->

BSC6900 V900R011 -> BSC6900 V900R011C00SPC300 or later version. Windows version

(windows is in the software name) should be used.

DocumentsBSC6900 PC OMU Operation Guide in Version Documents Method of Starting and Stopping PC OMU

net start omud

net stop omud

Default functions setting

Device panel display, FTP tool, alarm, tracing, and monitoring are disabled by default

Built-in OMU board mode, not the external BAM server mode
http://support.huawei.com/http://support.huawei.com/


15/61


Chapter 1 Summarize of Data Configuration

Chapter 2 Data Configuration


16/61


The Chat Flow of Data Configuration

Configuring the system

information

Configuring a cabinet

Configuring a subrack

Configuring a board

Configuring acommunication patch

between subracks

Configuring the time

The Equipment

Data

Configuring the

basic data

Configuring the

OPC

Global

Information

Configuring Ater

interface

Configuring A

interface

Configuring Gb

interface

Interface

Data

Set the Clock

source of

Interface board

Add the Clock

source of the

system Set the work

mode of the

system Clock

source

The Clocks

Data

Configuring the

BTS device data

Configuring the

logic data of the cell

Configuring the

transmission data

Activating BTS

data

GBTS and

Cells

Data configuration scene

BM/TC Separated. A, Ater, Abis Over TDM Transmission.

Inner PCU, Gb over FR.


17/61


Step 1: Configuring the Global Information

Finish

Begin

Configuring the

Equipment Data

Configuring the

Equipment Data

Configuring the Clocks

Configuring the

Global Information

Configuring a GSM

BTS and Its Cells

Configuring the

Basic Data

SET BSCBASIC1

2 ADD GCNOPERATEOR

Configuring OPCADD OPC3

4 ADD N7DPC


18/61



Configuring the Basic Data:

SET BSCBASIC: , , , , , ,

, ,

;

Aver, Umver, AbisVer: Phase tag for GSM protocols supported by the A interface. The value

of this parameter is chosen according to the A interface phase tag provided by the

MSC.Recommended Value: "GSM_PHASE_2" is recommended in common scenarios. If the

BSC needs to support GPRS services, EDGE services, AMR services, eMLPP services, inter-

RAT handover, and A over IP mode, "GSM_PHASE_2Plus" is recommended.

ServiceMode: Service mode of the BSC,GUI Value Range: SEPARATE(Separate),

TOGETHER(Together), AIP(AIP).

SptRanSharing: Whether to support RAN Sharing .

IsMainBSC: Whether the BSC is a primary BSC .

ATERTRANSMODE: Transport mode of the Ater interface. The Ater interface can be in TDM

or in IP transport mode.

Example:SET BSCBASIC: AreaCode=021, CC=86, AVer=GSM_PHASE_2Plus,

UmVer=GSM_PHASE_2Plus, AbisVer=GSM_PHASE_2Plus, HiFreqBandSupport=DCS1800,

ServiceMode=SEPARATE, ATERTRANSMODE=TDM;


19/61



Configuring the Basic Data:

ADD GCNOPERATOR: , , ,, ;

OperatorType: Primary operator or secondary operator, GUI Value Range: PRIM(Primary

Operator), SEC(Secondary Operator).

OPNAME: Name of the operator. This parameter uniquely identifies an operator.

MCC: Mobile country code. This parameter identifies the country where a

mobile .subscriber is located, for example, the Chinese MCC is 460.

MNC: Mobile network code. This parameter identifies the public land mobile network

(PLMN) where a mobile subscriber is homed.

Example:ADD GCNOPERATOR: OperatorType=PRIM, OPINDEX=0,

OPNAME="TEST", MCC="460", MNC="04", MSCPOOLALLOW=NO,

SGSNPOOLALLOW=NO;


20/61



Configuring the OPC

ADD OPC: , , , , NAME: OSP name.

SPX: OSP Index, To identify an OSP uniquely.

NINetwork ID. GUI Value Range: INT(INT), INTB(INTB), NAT(NAT), NATB(NATB).

SPCBITSOSP code bits. GUI Value Range: BIT14(BIT14), BIT16(BIT16), BIT24(BIT24).

SPCHexadecimal OSP code.

Example:ADD OPC: NAME="BSC130", SPX=0, NI=NATB, SPCBITS=BIT14,

SPC=H'0A03;


21/61



Configuring DPC

ADD N7DPC: , , , , , ; NAMEDSP name.

DPXThe DSP index uniquely indicates the corresponding relationship of an DSP and

OSP.

SPXTo identify an OSP uniquely.

DPCThe DSP code is in the hexadecimal format and cannot be 0. The value is unique

in the SS7 signaling network. The number of DSP bits is the same as that of the SPC. If

the designated bit is Bit14 in the adding of the SPC, the value range of the parameter is

H'1~H'3FFF(1~16383). If the designated bit is Bit16 in the adding of the SPC, the value

range of the parameter is H'1~H'FFFF(1~65535). If the designated bit is Bit24 in the

adding of the SPC, the value range of the parameter is H'1~H'FFFFFF(1~16777215).

DPCTDSP type. GSM only mode configured as A. Example:ADD N7DPC: NAME="MSC", DPX=0, SPX=0, SPDF=WNF, DPC=H'0910,

DPCT=A;


22/61


Step 2: Configuring the Equipment Data

Finish

Begin

Configuring the

Interfaces

Configuring the

Global Information

Configuring the Clocks

Configuring the

Equipment Data

Configuring a GSM

BTS and Its Cells

Configuring the

System

Information

SET SYS1

Configuring a

CabinetADD CAB2

Configuring a

Subrack

ADD SUBRACK3

Configuring a

BoardADD BRD5

Configuring a

Communication Path

Between Subrack

ADD SRCONPATH6

Configuring the

Time

SET TZ7

8 ADD SNTPSRVINFO

4 SET SCUPORT


23/61



Configuring the System Information

SET SYS: , , ,

, ;

SYSDESCDescription of the Base Station Controller.

SYSOBJECTIDIdentifier of the Base Station Controller.

SYSCONTACTContact way of the Base Station Controller supplier.

SYSLOCATIONLocation of the Base Station Controller.

SYSSERVICESServices provided by the Base Station Controller.

Example:SET SYS: SYSDESC="LAB", SYSOBJECTID="001",

SYSLOCATION="XINTIANXIA";


24/61



Configuring a Cabinet

ADD CAB: , CNNumber of the cabinet .

CABTWhether the added cabinet is a remote cabinet.

ExampleADD CAB: CN=1, CABT=YES; Note

The MPR is configured by default. You cannot add or remove this cabinet by running the

MML command. The cabinets consist of the Main Processing Rack (MPR), Extended

Processing Rack (EPR), and TransCoder Rack (TCR).

If the TC subrack is configured in the local cabinet, the remote TCR cannot be configured.

Configuring a Subrack

ADD SUBRACK: , , ;

SRNNumber of the subrack.

SRNameName of the subrack to be added.

TYPEType of the subrack.

ISTCCENTRWhether the subrack is a remote main TC subrack.

ExampleADD SUBRACK: SRN=3, SRName="TC1", TYPE=TCS, ISTCCENTRAL=YES;ADD SUBRACK: SRN=1, SRName="EPR1", TYPE=EPS, WORKMODE=GO;


25/61



Configuring a Subrackenable the panel port of the SCUa board in themain subrack

SET SCUPORT: , , ;

SRNSubrack No.

PNPort No.

SwitchGUI Value Range: CLOSE, OPEN

ExampleSET SCUPORT: SRN=0, PN=0, Switch=OPEN;

SET SCUPORT: SRN=0, PN=2, Switch=OPEN; Note

For the active and standby SCUa boards, if you set the attributes of the port on one SCUa

board, those of the corresponding port on the other SCUa boards are also set.

Except for port 10 and 11 on the SCUa board in subrack 0 when the external OMU is used,

this command modifies the attributes of both an odd numbered port and an even numbered

port. For example, if the attributes of port 2 on the SCUa board are modified, the attributes

of port 3 are also modified. When the external OMU is used, only one of port 10 and port 11

on the SCUa board in subrack 0 can be enabled.


26/61



Configuring a Board

ADD BRD, , , , ,, ;

BRDCLASSClasses of boards classified according to function modules, GUI Value

Range: INT, DPU, XPU, TNU, OMU.

BRDTYPEType of the board.

LGCAPPTYPELogic function type of the board, GUI Value Range: OAM,

TDM_Switching, GCP, UCP, RGCP, RUCP, IBCA, GTC, GPCU, UUP, ATM, IP, FR,HDLC, TDM, GbIP, Abis_TDM, Ater_TDM, Pb_TDM, A_TDM, Abis_IP.

MPUSUBRACKNumber of the subrack where the MPU is located.

MPUSLOTNumber of the slot where the MPU is located.

Example:ADD BRD: SRN=0, BRDCLASS=XPU, BRDTYPE=XPUa,

LGCAPPTYPE=RGCP, SN=0;

ADD BRD: SRN=0, BRDCLASS=XPU, BRDTYPE=XPUa, LGCAPPTYPE=GCP,SN=8, MPUSUBRACK=0, MPUSLOT=0;


27/61

St 2 C fi i th E i t D t


28/61



Configuring the Time Zone

SET TZ: ,< DST>;

ZONETTime zone.

DST:Whether daylight saving time starts.

ExampleSET TZ: ZONET=GMT-0800DST=NO; Configuring the SNTP Server

ADD SNTPSRVINFO: , ;

IPIP address of the server.

PTNumber of the port that provides the time information on the SNTP server.

Example:ADD SNTPSRVINFO: IP="192.168.88.200", PT=123;

Note:

The number of SNTP servers cannot exceed 16.

If multiple SNTP servers are configured, the OMU selects the best SNTP server as the

clock source according to the algorithm defined in the Network Time Protocol (NTP).

The IP address is the IP address of the SNTP server. The SNTP client in the active OMU

receives the time information from the SNTP server. The IP address cannot be set to a

special address such as 0.0.0.0 or 127.0.0.1.

St 3 C fi i th I t f


29/61


Step 3: Configuring the Interfaces

Finish

Begin

Configuring the

Equipment Data

Configuring the

Global Information

Configuring Clock

Configuring the

Interface

Configuring a GSM BTSand Its Cells

Configuring the A

interface

Configuring the physic Layer over A interface

ADD AE1T1

5

Configuring the control plane Over A interface

ADD MTP3LKS

ADD MTP3LNK

ADD MTP3RT

6

Configuring the

Ater Interface

Configuring an Ater Connection Path

ADD ATERCONPATH1

Configuring an Ater OML

ADD ATEROML

2

Configuring an Ater Signaling Link

ADD ATERSL3

Configuring the

GB Interface

Configuring PCU type

SET BSCPCUTYPE7

Configuring SGSN node

ADD SGSNNODE8

Configuring NSE

ADD NSE9

Configuring BC

ADD BC10

Configuring NSVC

ADD NSVC11

Configuring PTPBVC

ADD PTPBVC12

4 Configuring the CN node

ADD GCNNODE

St 3 C fi i th I t f At I t f


30/61


Step 3: Configuring the InterfaceAter Interface

Configuring an Ater connection path

ADD ATERCONPATH, , , , ,, ;

ATERIDXIndex of an Ater connection path.

BMSRNBMSNBMPNBM Subrack NO, Slot NO, Port NO.

TCSRNTCSNTCPNTC Subrack NO, Slot NO, Port NO.

Example:ADD ATERCONPATH: ATERIDX=0, BMSRN=0, BMSN=14, BMPN=0,

TCSRN=3, TCSN=14, TCPN=0;

Note

This command applies only in BM/TC separated configuration mode.

If the TC pool function is enabled, this command applies to only the active BSC. For the

standby BSCs, you need to run the ADD ATERE1T1command to add the Ater

connection path.

Step 3: Configuring the Interface Ater Interface


31/61


Step 3: Configuring the InterfaceAter Interface

Configuring Ater OML

ADD ATEROML: , , ;

ATEROMLINX

Ater maintenance link index. ATERPIDXAter connection path index.

TSMASKTime slots for Ater operation and maintenance. These time slots are provided by

the ports connected to the Ater connection path.

ExampleADD ATEROML: ATEROMLINX=0, ATERPIDX=0, TSMASK=TS1-1&TS2-1&TS3-1&TS4-1&TS5-1&TS6-0&TS7-0&TS8-0&TS9-0&TS10-0&TS11-0&TS12-0&TS13-0&TS14-

0&TS15-0&TS16-0&TS17-0&TS18-0&TS19-0&TS20-0&TS21-0&TS22-0&TS23-0&TS24-

0&TS25-0&TS26-0&TS27-0&TS28-0&TS29-0&TS30-0&TS31-0;

Note

Only the remote TCS can be configured with the OML on the Ater interface.

Before configuring the OML on the Ater interface, you must configure the Ater connection path.

The Ater OML only configured between the local switching subrack and the remote main

subrack. The BM and TC subracks used for the OML on the Ater interface must be main

subracks.

Besides timeslot 1, the OML on the Ater interface must contain four consecutive timeslots.

At most two OMLs on the Ater interface can be configured in the entire system.


32/61

Step 3: Configuring the Interface A Interface


33/61


Step 3: Configuring the InterfaceA Interface

Configuring GSM CN Node

ADD GCNNODE: , , , ,

;

CNNODEIDXNode index of an MSC.

DPXCode of a destination signaling point (DSP) in a signaling network. In a signaling

network, each signaling point has a corresponding signaling point code (SPC).

DPCGIDXSignaling group of a DSP.

If multiple DSPs or one DSP serves as a logical entity, this logical entity is a DSP group.

OPNAMEName of the operator. This parameter uniquely identifies an operator.

CNIDUsed to uniquely identify an MSC.



34/61



DFDPC: For the default DPC corresponds to the CN of the primary operator: when only

one DPC is configured, this parameter must be set to "YES", indicating that all the calls

for the operator are accessed through the CN identified by the DPC. When multiple DPCs

are configured, this parameter also determines the DPC that allows the generation of

ESN. In this case, the parameter is set to "YES" for this DPC while the value for other

DPCs is "NO".

For the CN of a secondary operator, this parameter must be set to Yes" when only one

DPC is configured. This indicates that all the calls for the secondary operator areaccessed through the CN. When multiple DPCs are configured, this parameter is invalid.

Example:ADD GCNNODE: CNNODEIDX=0, DPX=0, DPCGIDX=0, OPNAME="TEST",

CNID=0, DFDPC=YES;



35/61



Configuring the Physical Layer

ADD AE1T1: , , , , , ,

; STCICNumber of the start CIC. The C/C of each E1/T1 timeslot can be calculated on

the basis of this parameter. Assume that the start CIC is 100, the CIC of the E1 timeslots

on the A interface will automatically be set to 100, 101, 102, 103, and so on. Assume that

the CIC of an E1 timeslot is 65535, the CICs of all successive E1 timeslots are all 65535.

BSCFLAGIt indicates whether the A interface E1/T1 is the primary BSC or secondary

BSC.

Example:ADD AE1T1: SRN=0, SN=16, PN=0, STCIC=0, DPCGIDX=0, OPCIDX=0,

BSCFLAG=MAINBSC;

Note

You can configure up to 512 E1/T1 links on the A interface board.

The CICs of the two E1/T1 timeslots on the A interface with the same OSP indexand

DPC Group Indexmust be different. In practice, however, running this command always

fails due to the same CIC of the two timeslots. In this case, you need to adjust the Start

CICto ensure that the CIC of an E1/T1 timeslot on the A interface differs from that of

another timeslot.



36/61



Configuring the Control Plane

ADD MTP3LKS: , , ;

SIGLKSXTo identify an signaling link set uniquely.


NAMESignaling link set name.

Example:ADD MTP3LKS: SIGLKSX=0, DPX=0, NAME="LINK1";

Note

The DSP specified by DSP index must exist, and it must be an adjacent DSP.

One adjacent DSP can be configured with only one signaling link set.



37/61




ADD MTP3LNK: , , , , ,

, , , , , ; SIGLKSXTo identify an signaling link set uniquely.

SIGSLCM3UA link ID of the specified link set.

TCMODETo specify the mode of TC. GUI Value Range:

SEPERATE_PRINCIPAL(Principal BSC), SEPERATE_SUBORDINATE(Subordinate

BSC), TOGETHER(BSC/TC Together).

ATERIDXIndex of an Ater connection path.

ATERTSMASKAter interface timeslot mask.

MTP2LNKNTo identify an MTP2 link.

APNA interface port No..

ATSMASKA interface timeslot mask.



38/61




Example:ADD MTP3LNK: SIGLKSX=0, SIGSLC=0,

TCMODE=SEPERATE_PRINCIPAL, ATERIDX=0, ATERMASK=TS1-0&TS2-0&TS3-0&TS4-0&TS5-0&TS6-0&TS7-0&TS8-0&TS9-0&TS10-0&TS11-0&TS12-0&TS13-


0&TS24-0&TS25-0&TS26-0&TS27-0&TS28-0&TS29-0&TS30-0&TS31-0, ASRN=3,

ASN=16, MTP2LNKN=0, APN=0, ATSMASK=TS1-0&TS2-0&TS3-0&TS4-0&TS5-0&TS6-


1&TS17-0&TS18-0&TS19-0&TS20-0&TS21-0&TS22-0&TS23-0&TS24-0&TS25-0&TS26-0&TS27-0&TS28-0&TS29-0&TS30-0&TS31-0, NAME="mtp3link0";



39/61



Note

The link set to be used must exist.

Signalling Link Codemust be set to the same value at the two ends of the signaling link.

The total number of MTP3 signaling links cannot exceed 1904.

The number of MTP3 links controlled by the same CPUS subsystem cannot exceed 50.

ADD MTP3RT: , , < NAME>;


OSP.

SIGLKSXTo identify an signaling link set uniquely. NAMEOne MTP3 route name.

Example:ADD MTP3RT: DPX=0, SIGLKSX=0, NAME="RT1";

Note

DSP indexand Signalling link set indexmust exist.

If the DSP specified by DSP indexis inconsistent with that specified by Signalling link

set index, you need to check whether the DSP specified by Signalling link set index

has a transfer function.

In addition to a direct route, it is recommended to add an alternative route as a backup.

At most 238 MTP3 routes can be configured for the BSC.

Step 3: Configuring the InterfaceGb Interface


40/61


Step 3: Configuring the Interface Gb Interface

Configuring the PCU Type

SET BSCPCUTYPE: ;

TYPEType of the PCU.

GUI Value Range: OUTER(Outer PCU), INNER(Inner PCU).

Example: SET BSCPCUTYPE: TYPE=INNER;

Configuring the SGSN Node

ADD SGSNNODE: , ;

OPNAMEName of the operator. This parameter uniquely identifies an operator. CNIDIdentifies a service provider.

Example:ADD SGSNNODE: OPNAME="TEST", CNID=0;



41/61


Step 3: Configuring the Interface Gb Interface

Configuring an NSE

ADD NSE: , , , , , ;

NSEIIdentifies a unique NSE. SRNSNSubrack number and slot number of the XPU bound to the.

PTSubnet protocol type. GUI Value Range: GB_OVER_FR(Gb over FR),

GB_OVER_IP(Gb over IP).

OPNAMEName of the operator. This parameter uniquely identifies an operator.

CNIDIdentifies a service provider.

Example:ADD NSE: NSEI=0, SRN=0, SN=0, PT=GB_OVER_FR, OPNAME="TEST",

CNID=0;

Note

The NSE must be configured in the MPS or EPS.

A BSC can be configured with up to 128 NSEs.

When Protocol typeis set to GB_OVER_IP and Subnetwork Configure Modeis set to

DYNAMIC, then Server IPand Server Portare determined by the serving GPRS support

node (SGSN). If Subnetwork Configure Modeis set to STATIC, then Server IPand

Server Portneed not be set.

NSE identifiermust be consistent with that on the SGSN side.



42/61


p g g

Configuring a BC

ADD BC: , , , , ;

SRNSNPN: Subrack number, Slot number, Port number.

BCIDIdentifies one BC at the same port. The BCID's value range of PEUa board is

0~255 and that of POUc board is 0~511.

TSTimesolt of bearing channels.

Example:ADD BC: SRN=0, SN=24, PN=0, BCID=0, TS=TS1-1&TS2-1&TS3-1&TS4-


1&TS15-1&TS16-1;

Note

Bearing timeslotand Protocol typemust be consistent with those on the Serving GPRS

Support Node (SGSN) side.



43/61


p g g

Add NSVC

ADD NSVC: , , , , , , ;

NSVCIDX

NSVC index, identifying a unique NSVC. NSVCINSVC ID, identifying a unique NSE. This ID must be negotiated with the peer

SGSN.

NSEIIdentifies a unique NSE.

BCIDIdentifies one BC at the same port. The BCID's value range of PEUa board is

0~255 and that of POUc board is 0~511.

DLCIID of the data link connection of the NSVC. It is an interworking parameter which

must be consistent on the BSC and the peer.

Example:ADD NSVC: NSVCIDX=0, NSVCI=0, NSEI=0, SRN=0, SN=24, BCID=0,

DLCI=16;

Note

An NSVC is carried on a bearer channel (BC) on the E1/T1 link. A BC can be configured

with several NSVCs (differentiated by The identifier of Data Link Connection). AnNSVC can belong to only one BC and only one NSE, whereas an NSE can correspond to

several NSVCs.

NSE identifier, NSVC identifier, and The identifier of Data Link Connectionmust be

consistent with those on the SGSN side.



44/61


p g g

Configuring a PTPBVC

ADD PTPBVC: , , , ;

NSEIIdentifies a unique NSE.

BVCIIdentifies one PTP BVC.

IDTYPESubscribers can specify the cell according to the index or the name.

GUI Value Range: BYNAME(By Name), BYID(By Index).

Example:ADD PTPBVC: NSEI=0, BVCI=2, IDTYPE=BYNAME, CELLNAME="CELL1";

Note

When the SGSN pool function is disabled, a cell can be configured with only one PTP

BVC. When the SGSN pool function is enabled, a cell can be configured with up to 32

PTP BVCs.

An NSE can support up to 2048 PTP BVCs.

This command can be used only in built-in PCU mode.

Step4: Configuring the Clocks


45/61


p g g

Finish

Begin

Configuring the

Interface

Configuring the

Equipment Data

Configuring the

Global Information

Configuring Clock

Configuring a GSM BTSand Its Cells

set the clocksource

SET CLK1

add the clock

source of the

system

ADD CLKSRC2

set the work mode

of the system

clock source

SET CLKMODE3


46/61



47/61


Add Clock Source

ADD CLKSRC: , ;

SRCGRDPriority of the clock source. GUI Value Range: 1~4.

SRCTType of the clock source. GUI Value Range: BITS1-2MHZ(2MHZ Building

Integrated Timing Supply system 1), BITS2-2MHZ(2MHZ Building Integrated Timing

Supply system 2), BITS1-2MBPS(2MBPS Building Integrated Timing Supply system 1),

BITS2-2MBPS(2MBPS Building Integrated Timing Supply system 2), 8KHZ(8KHZ),

GPS(Globe Positioning System), LINE1_8KHZ(8KHZ line1), LINE2_8KHZ(8KHZ line2),BITS1-T1BPS(T1BPS Building Integrated Timing Supply system 1), BITS2-

T1BPS(T1BPS Building Integrated Timing Supply system.

Example:ADD CLKSRC: SRCGRD=1, SRCT=LINE1_8KHZ



48/61


Set Clock Working Mode

SET CLKMODE: ; MODEWorking mode of the system clock. Working modes of the system clock are as

follows:

(1) MANUAL: In this mode, you must specify a clock source and prevent the switching of

the clock source.

(2) AUTO: In this mode, you do not need to specify a clock source and the system

automatically selects the clock source with the highest priority.(3) FREE: In this mode, the clock source of GCGa or GCUa is used.

GUI Value Range: MANUAL, AUTO, FREE

Example:SET CLKMODE: MODE=AUTO;

Note

If the manually-set clock source is unavailable, the switchover fails. Then, the current

clock source remains unchanged.

Step 5: Configuring a GSM BTS and Its Cells


49/61


Finish

Begin

Configuring the

Equipment Data

Configuring the

Global Information

Configuring Clock

Configuring a GSMBTS and Its Cells

Configuring the

Interface

Configuring the

Equipment Data

Configure BTS

ADD BTS1

Configure BTS subrack

ADD BTSCABINET2

Configuring the

Logical Data

Configure Cell data

ADD CELL

ADD GCELLOSPMAP

ADD GCELLFREQ

4

Configure TRX data

ADD BTSTRXBRDADD BTSRXUCHAIN

ADD BTSRXUBRD

ADD GTRX

5

Bind a Cell to a BTS

ADD CELLBIND2BTS

6

Configure BTS board

ADD BTSBRD3

Bind a physical board to

a logic TRX

ADD TRXBIND2PHYBRD

7

Configuring the

Transmission DataADD BTSCONNECT8

Activating the BTS

ConfigurationACT BTS9



50/61


Configuring a GSM BTS

ADD BTS: < BTSID>, , , ; SEPERATEMODEWhether to enable the BTS to support the separation between the

physical and logical. GUI Value Range: SUPPORT(Support), UNSUPPORT(Not Support).

SERVICEMODEService bearer mode of the BTS. GUI Value Range: TDM, HDLC,

HDLC_HubBTS, IP.

SRANMODEWhether to enable the BTS to identify an object in the BTS in normalized

mode, for example, to identify a board by the slot No., subrack No., and cabinet No. and

to identify a transmission port by the port No. in a board. GUI Value Range:

SUPPORT(Support), NOT_SUPPORT(Not Support).

Example:ADD BTS: BTSID=0, BTSNAME="BTS3900", BTSTYPE=BTS3900_GSM,

SEPERATEMODE=SUPPORT, SERVICEMODE=TDM, SRANMODE=SUPPORT;



51/61


Add BTS Cabinet

ADD BTSCABINET: , ,, ;

IDTYPEIndex type of the BTS. BYNAME: query by BTS name; BYID: query by BTS

index. GUI Value Range: BYNAME(By Name), BYID(By Index).

BTSIDID of the BTS. The BTS ID must not conflict with other BTS IDs in the BSC.

CNNumber of the cabinet.

TYPEType of a cabinet.

Example:ADD BTSCABINET: IDTYPE=BYID, BTSID=1, CN=0, TYPE=BTS3012;

Add BTS Board

ADD BTSBRD:, , , , ;

Example:ADD BTSBRD: IDTYPE=BYID, BTSID=0, CN=0, SRN=11, SN=0, BT=FMU;



52/61


3900 Series Base Stations

ADD BTSRXUCHAIN:, , , , , ,

, ;

Number of the RXU chain or ring. The value scope is 0~11 for Non-SRAN BTS and 0~249 for

SRAN BTS. The RXU chain No. is unique in the same BTS. A maximum of 12 RXU chains

can be configured in one BTS.

RXU topology type, that is, RXU ring topology or RXU chain topology. In the case of the ring

topology, the optical ports of the head and tail boards must be specified. In the case of thechain topology, only the optical port of the head board must be specified.

Number of the cabinet where the head board of the RXU chain or ring is located.

HSRN:Number of the subrack where the head board of the RXU chain or ring is located. The

subrack No. is unique in the same BTS.

HSN: Number of the slot where the head board of the RXU chain or ring is located. The slot

No. is unique in the same BTS.

HPN:The number of the optical port of the head board in the RXU chain or ring.

Example:ADD BTSRXUCHAIN: IDTYPE=BYID, BTSID=0, RCN=0, TT=CHAIN, HCN=0,

HSRN=0, HSN=6, HPN=0;



53/61


3900 Series Base Stations

ADD BTSRXUBRD:, , , , , ,

, , ;

BT:Type of the newly added RXU board. GUI Value Range: DRRU(DRRU),

DRFU(DRFU), MRRU(MRRU), XRRU(XRRU), MRFU(MRFU), GRFU(GRFU),

GRRU(GRRU), XRFU(XRFU), BTS3900E(BTS3900E).

RXUCHAINNO: Number of the RXU chain where the board is located.

RXUPOS: Position of the RXU board on an RXU chain. Example:ADD BTSRXUBRD: IDTYPE=BYID, BTSID=0, BT=DRFU, CN=0, SRN=4,

SN=0, RXUNAME="drfu0", RXUCHAINNO=0, RXUPOS=1;



54/61


Set the Send/Receive Mode and Work Mode of the RXU Board

SET BTSRXUBP:, , , ,

, ;

RXUIDTYPE: Type of the RXU board index.

RXUNAME: Name of the RXU board. The RXU name is unique in one BTS.

RXUTYPE: Type of the RXU board. GUI Value Range: DRRU(DRRU), DRFU(DRFU),

MRRU(MRRU), MRFU(MRFU), GRFU(GRFU), GRRU(GRRU), BTS3900E(BTS3900E).

SndRcvMode3: Sending and receiving mode of the MRFU/GRFU board. GUI Value

Range: SGL_ANTENNA(Single Feeder[1TX + 1RX]), SGLDOUBLE_ANTENNA(Single

Feeder[1TX + 2RX]), DOUBLE_ANTENNA(Double Feeder[2TX + 2RX]),

DOUBLEFOUR_ANTENNA(Double Feeder[2TX + 4RX]),

DOUBLESINGLE_ANTENNA(Double Feeder[1TX + 1RX]),

DOUBLEDOUBLE_ANTENNA(Double Feeder[1TX + 2RX]). Actual Value Range:

SGL_ANTENNA, SGLDOUBLE_ANTENNA, DOUBLE_ANTENNA,

DOUBLEFOUR_ANTENNA, DOUBLESINGLE_ANTENNA,

DOUBLEDOUBLE_ANTENNA;

Step 5: Configuring the Logical Data


55/61


Add BSC Cell

ADD GCELL: , , , , , ,

; CELLIDIndex of a cell, uniquely identifying a cell in a BSC.

CELLNAMEName of a cell, uniquely identifying a cell in a BSC.

TYPEThis parameter specifies the frequency band of new cells. Each new cell can be

allocated frequencies of only one frequency band. Once the frequency band is selected, it

cannot be changed.

MCCMobile country code. This parameter identifies the country where a mobilesubscriber is located, for example, the Chinese MCC is 460.

MNC: Mobile network code. This parameter identifies the public land mobile network

(PLMN) where a mobile subscriber is homed.

LACLocation area code (LAC). MSs can freely move in the local location area with no

need of location update. Reasonable local allocation can effectively lighten the signaling

load and improve the call completion rate. CIIdentity code of a cell.

ExampleADD GCELL: CELLID=0, CELLNAME="cell0", TYPE=GSM900, MCC="460",MNC="10", LAC=10, CI=11;



56/61


The Relation Between Cell And OSP

ADD GCELLOSPMAP: , , ;

IDTYPEType of an index. GUI Value Range: BYNAME(By Name), BYID(By Index). CELLIDIndex of a cell, uniquely identifying a cell in a BSC.

OPC: Code of the original signaling point (OSP) in the signaling network. In the signaling

network, each signaling point is identified by a signaling point code.

Example:ADD GCELLOSPMAP: IDTYPE=BYID, CELLID=0, OPC=H'A03;

Configure the logic Data-Add Cell Frequency

ADD GCELLFRQ: , , ;

FREQ1: Frequency 1

Example:ADD GCELLFREQ: IDTYPE=BYID, CELLID=0, FREQ2=2;

Configure the logic Data-Add GSM TRX

ADD GTRX: < IDTYPE>, , , ; FREQ: Frequency of the TRX.

ISMAINBCCHWhether to enable the TRX to carry the main BCCH in the cell. GUI

Value Range: NO(No), YES(Yes).

Example:ADD GTRX: IDTYPE=BYID, CELLID=0, TRXID=0, FREQ=2,

ISMAINBCCH=YES;



57/61


Bind a Cell to a BTS

ADD CELLBIND2BT: , , ;

Example:ADD CELLBIND2BTS: IDTYPE=BYID, CELLID=0, BTSID=0

Configuring the Binding Between a Logical TRX and a Physical TRX Board

ADD TRXBIND2PHYBRD: , , , , ;

TRXIDID of the TRX. The TRX ID must be globally unique.

TRXTPType of the TRX board bound to the TRX. GUI Value Range: TRX(TRX),

TRU(TRU/DTRU), QTRU(QTRU), DRRU(DRRU), DRFU(DRFU), MRRU(MRRU),

MRFU(MRFU), GRFU(GRFU), GRRU(GRRU), BTS3900B(BTS3900B),

BTS3900E(BTS3900E).

TRXPNNumber of the channel bound to the TRX on the TRX board.

Example:ADD TRXBIND2PHYBRD: TRXID=0, TRXTP=DRFU, TRXPN=0,

RXUIDTYPE=SRNSN, CN=0, SRN=4, SN=0;

Note

For TRX boards of the DBS3900 GSM, BTS3900 GSM, BTS3900A GSM, DBS3036,

BTS3036, BTS3036A, BTS3900B GSM and BTS3900E GSM, you need to specify the

attributes of the RXU link.

Step 5: Configuring the Transmission Data


58/61


Add BTS Connect

ADD BTSCONNECT: , , , , ,

, ; IDTYPEIndex type of the BTS. BYNAME: query by BTS name; BYID: query by BTS

index. GUI Value Range: BYNAME(By Name), BYID(By Index).

BTSIDID of the BTS. The BTS ID must not conflict with other BTS IDs in the BSC.

INPNNumber of a BTS port.

DESTNODEType of the object the BTS is connected to. Value range: BTS, BSC, and

DXX. GUI Value Range: BTS, BSC, DXX, OTHER.

Example:ADD BTSCONNECT: IDTYPE=BYID, BTSID=0, INPN=0, INCN=0, INSRN=0,

INSN=6, DESTNODE=BSC, SRN=0, SN=18, PN=0;

Note

The connection between the BSC and the BTS is not required for the IP-based BTS that

supports IP over FE/GE transmission.

Step 5: Activating the BTS Configuration


59/61


Act BTS

ACT BTS: , ;

IDTYPEType of an index. GUI Value Range: BYNAME(By Name), BYID(By Index).

BTSIDID of the BTS.

Example:ACT BTS: IDTYPE=BYID, BTSID=0;

Note

After this command is run, the BTS is initialized. This command can also be used to

check the BTS data as some data check is not done when BTS is not active in BSC6900.

Step 5: Configuring a GSM BTS and Its CELL


60/61


Quickly Configuring a GSM Cell

ADD GCELLQUICKSETUP: , , , ,

, , , , , ; CELLID: Index of a cell, uniquely identifying a cell in a BSC.

CELLNAME: Name of a cell, uniquely identifying a cell in a BSC.

TYPECell type. Currently, the fast BTS construction is available for only GSM900 and

DCS1800 cells. GUI Value Range: GSM900(GSM900), DCS1800(DCS1800).

MCCMNCLACCIMobile country code. Mobile network code. Location area code

(LAC). Identity code of a cell. BCCHFREQFrequency of the BCCH TRX.

OTHERFREQOrdinary frequency. Multiple frequencies are separated by "&". For

example, "22&33&44&55" are allocated to TRXs in ascending order.

Example:ADD GCELLQUICKSETUP: CELLID=1, CELLNAME="CELLA",

TYPE=GSM900, MCC="460", MNC="04", LAC=10, CI=3, OPC=H'A03, BCCHFREQ=12,

OTHERFREQ="33&55";


61/61

Thank You

www.huawei.com