011-011
TRANSCRIPT
-
8/3/2019 011-011
1/33
SPECIFICATIONS
A FIXED FOUNTAIN SYSTEM
1.0 GENERAL
1.1 DESCRIPTION
A. Manufacturer shall furnish a fixed fountain aeration system capable of
pumping water from below the surface of a body of water.
B. A submersible motor shall draw water into an impeller housing where
it shall be pumped into the atmosphere in the form of a decorative spray-
type fountain.
C. The water droplets shall become oxygen enriched and return to the
surface, therefore transferring oxygen from the atmosphere into the body of
water. Surface area of water body shall also be increased through constant
wave action resulting in additional atmospheric oxygen transfer.
D. This repeated action shall effectively mix and de-stratify the body of
water and distribute the dissolved oxygen continuously.
E. Fountain system shall include an oil-cooled motor sealed in a stainless
steel housing, with shaft mounted impeller inside a discharge tube. This
assembly shall be connected to an electrical control panel by underwater
power cable, all of which as specified in SECTION 1.2.
1.2 AERATOR COMPONENTS DESCRIPTION
A. Frameworkshall be a weldment of rectangular and square Series 300
Stainless Steel tubing with a minimum wall thickness of 1/8 inch. Pump
support brackets (horizontal only) shall be made out of PVC, nylon, other non
metallic material and Series 300 stainless steel to give the power/pump unit
proper support. All fasteners shall be Series 300 Stainless Steel.
B. Discharge Tube shall be manufactured out of PVC for proper
diameter and shall be of proper length to insure that the discharge assembly
and pattern are above the highest water level when the unit is running.
C. Impeller housing shall be cast from nylon type 6 material. The
impeller housing shall be precision machined to accept the float tube and
capable of being bolted to the motor housing. The impeller housing shall
house the stainless steel impeller, insert and flow straightener (if applicable).
D. Flow Straightener shall be precision machined from nylon type 6
material and shall have 18 curved vanes. The vanes shall take the spinning
01/07Page 1
-
8/3/2019 011-011
2/33
discharge water from the impeller and convert it to a straight, vertical flow.
The gap between the vanes shall be at least 3/8 wide and have a total
length not less than 2-1/2 long. It shall be factory installed for various
optional spray patterns.
E. Motor housing shall be Series 300 Stainless Steel. 1-5HP shall have
a permanent Series 300 Stainless Steel electrical hub welded on the side of
the housing to allow electrical cable entry. The 1/2HP shall have a Series 300
Stainless Steel electrical hub welded on the bottom of the housing to allow
electrical cable entry.
01/07Page 2
-
8/3/2019 011-011
3/33
F. Motor shall contain a Series 300 Stainless Steel shaft incorporating a
permanent split phase capacitor run on single phase motors and a polyphase
induction on three phase motors. The rotor shall be dynamically balanced
and run in a ball bearing supported system. The stator windings shall be
double dipped and baked with a Class F insulation, designed for oil
immersion operation. The oil shall be a highly refined, mineral oil of food
grade quality, specially formulated for lubrication. It shall meet FDA
regulations. The oil shall provide continuous lubrication of bearings and
internal seals and further function as an efficient heat transfer medium,
allowing the motor to operate at 3450 RPM, at relatively low temperatures.
The motor shall be contained in the motor housing by a Series 300 Stainless
Steel top plate.
G.
Seals used to protect the motor against water or oil leakage shall be amechanical, rotating type assembly, composed of silicon carbide and Series
300 Stainless Steel. All elastomers shall meet UL 778 requirements. This
assembly shall then be encapsulated and protected within a Series 300
Stainless Steel cartridge assembly.
H. Underwater power cable shall be UL Listed and specifically
designed for underwater use. The conductors are flexible, stranded copper
wire sized for the amp draw and length of run. The conductors shall be
resistant to oil, water and cracking. Power cable shall be fitted with a cablestrain relief device, located within five feet of motor housing, capable of
being attached to the S hooks mounted on the motor housing clamp. This
will ensure that no potential damage can occur to any cable connections, due
to tension on the cable.
I. Underwater power cable disconnect shall be located
approximately three feet from the motor housing. It is a two piece molded
assembly made of thermoplastics, meeting UL 778 requirements. The cap
end shall be permanently connected to the underwater pin and socketconnector (see Section 1.2 Item J.). The body end of the disconnect shall be
permanently attached to the underwater power cable and sealed with an
approved compound. This is intended to prevent water entry if damage
should occur to the cable. The disconnect shall be sealed with an internal o-
ring and by an external Series 300 Stainless Steel clamp ring, which can be
easily opened.
01/07Page 3
-
8/3/2019 011-011
4/33
J. Underwater Pin and Socket Connector (1-5HP)shall consist of a
Series 900 IP68 pin and socket connector. It shall be of a 4 pin configuration
rated 32 amps at 600 volts AC. The pin end shall be potted into a Series 300
Stainless Steel 90 adapter elbow with an approved ridged epoxy. This
assembly shall be permanently attached to the Series 300 Stainless Steel
hub that is welded onto the side of the Series 300 Stainless Steel motor
housing. The socket end shall be attached to a 36 piece of UL Listed
underwater power cable. It shall be permanently secured to the UL Listed
power cable by means of an integrated clamp and Series 300 Stainless Steel
screws. It shall be completely epoxied to prevent entry of water or any other
foreign matter. The other end of this assembly is permanently attached to
the cap end of the underwater cable disconnect. It is sealed with a flexible
potting compound.
1/2HP shall consist of a Series 900, IP68 pin and socket connector. It shall be
of a 4 pin configuration rated 32 amps at 600 volts AC. The pin end shall be
potted into a Series 300 Stainless Steel straight bell-shaped adapter with an
approved ridged epoxy. This assembly shall be permanently attached to a
reinforced braided hose and a Series 300 Stainless Steel elbow. This shall be
attached to a Series 300 Stainless Steel hub which is welded on the bottom
of the motor housing. This complete assembly shall be sealed with an
approved flexible potting compound. The socket end shall be attached to a
36 piece of UL Listed underwater power cable. It shall be permanently
secured to the UL Listed power cable by means of an integrated clamp and
01/07Page 4
-
8/3/2019 011-011
5/33
Series 300 Stainless Steel screws. It shall be completely epoxied to prevent
entry of water or any other foreign matter. The other end of this assembly
shall be permanently attached to the cap end of the underwater cable
disconnect. It shall be sealed with an approved flexible potting compound.
K. Fasteners and anchor connectors shall be Series 300 Stainless
Steel.
L. Electrical control panel specifications, see SECTION 3.
M. Intake screen shall be made of 20 Gauge, Series 300 Stainless Steel.
The screen shall have a minimum of 58% open area, representing 91 square
inches of open intake area.
N. Large custom intake screen (optional for 1-5HP) shall be made of
18 Gauge Series 300 Stainless Steel and completely enclose the motor power
unit assembly. It shall have a minimum of 58% open area, representing 765square inches of open intake area. The screen hole size shall vary according
to the horsepower for which it is to be used on.
O. Nozzles (first one is included, must be specified, additional are
optional) shall be interchangeable without the use of tools. Nozzles will be
sealed to the float tube utilizing an o-ring and stainless steel thumb screws to
prevent leakage.
01/07Page 5
-
8/3/2019 011-011
6/33
FIXED FOUNTAIN DETAIL SPECIFICATIONS
2.0 DETAILED INFORMATION
2.1 This specification is intended to provide prospective bidders the necessary
information pertaining to the fixed fountain(s) specified for the_______________________ Project.
2.2 The MOTOR(S) shall be _____ HP, operating at _____ Volts, 60 Hertz, _____ Phase at
3450 RPM.
2.3 The pattern specified shall be capable of creating a ________________________ pattern.
It shall come complete with an electrical control panel, protective intake screen to
be attached to a float assembly and ________ feet of _______ gauge, 3 (1/2 HP
models only) or 4 conductor underwater power cable.
2.4 The fountain shall produce a SPRAY PATTERN _____feet in diameter and _____feet in
height.
Please refer to TABLES 1, 2 and 3 to assist in the completion of SECTION 2.0
01/07Page 6
-
8/3/2019 011-011
7/33
FIXED FOUNTAIN DETAIL SPECIFICATIONS (cont.)
3.0 ELECTRICAL CONTROL PANEL COMPONENTS DESCRIPTION
A. Electrical enclosure shall be NEMA 3R type, galvanized and powder-
coat painted gray in color. Panel shall be both lock and mount capable.
B. GFCI breaker shall provide overload and short circuit protection,
combined with Class A ground fault protection.
C. Control breaker shall provide overload protection and be capable of
disconnecting all incoming electricity from the control panel.
D. Motor contactor shall provide a means for disconnection of all motor
leads. It shall be a magnetic, across the line starter type.
E. Overload assembly shall provide overload protection by means of a
bi-metallic overload relay. It is adjustable over the full load amperage draw
of the motor. It shall have a visual trip indicator, test button and
manual/automatic reset modes.
F. Timer shall be a single pole type, rated at 120 Volts, 20 Amps,
capable of a timing cycle, in 30 minute increments up to 24 hours.
3.1 SAFETY TESTING CONTROL PANEL
The electrical control panel shall be tested and approved as a complete unit. It is
inspected and listed by Underwriters Laboratories, Inc. under Category 508:
Industrial Control Panels and Category 778: Submersible Aerators and Aerating
Fountain Pump Systems.
3.2 ACCEPTABLE MANUFACTURER
This fixed fountains electrical control panel, as specified in Section 3.0, shall be
manufactured by AQUAMASTER
FOUNTAINS AND AERATORS, 16024 CTH X, Kiel, WI
53042, (800) 693-3144 or approved equal.
3.3 INSTALLATION
The electrical control panel must be installed in accordance with the installation
instructions, in compliance with all local and National Electrical Code requirements.
This should be done by a licensed electrical contractor. Any alterations to or
substitution for items in this system, unless allowed by the installation instructions,
will void the Underwriters Laboratories Listing and will void the product warranty. It
may also create a hazardous installation. Read the instructions thoroughly before
starting the installation and follow them carefully throughout.
01/07Page 7
-
8/3/2019 011-011
8/33
3.4 ELECTRICAL CONTROL PANEL WARRANTY
All electrical panel and on-shore components shall have a 1 year warranty.
01/07Page 8
-
8/3/2019 011-011
9/33
FIXED FOUNTAIN DETAIL SPECIFICATIONS (cont.)
4.0 SAFETY TESTING
The fixed fountain system shall be tested and approved as a complete unit. This
approval must meet Underwriters Laboratories Inc. requirements in compliance with
Category 508: Industrial Control Panels and Category 778: Submersible Aerators
and Aerating Fountain Pump Systems. Individual component testing and wet niche
environment equipment approval are not acceptable.
4.1 ACCEPTABLE MANUFACTURER
This fixed fountain, as specified in Sections 2.2, 2.3 and 2.4, shall be manufactured
by AQUAMASTER
FOUNTAINS AND AERATORS, 16024 CTH X, Kiel, WI 53042, (800)
693-3144, or approved equal.
4.2 INSTALLATION
All AQUAMASTER
FOUNTAINS are designed and built to be installed with an
AQUAMASTER
UL Listed control panel and to be operated as a complete system.
Any alterations to or substitution for items in this system, unless allowed by the
installation instructions, will void the UL Listing and will void the product warranty.
It may also create a hazardous installation. Read the instructions thoroughly before
starting the installation and follow them carefully throughout.
4.3 WARRANTY
All 1 5HP AQUAMASTER
FOUNTAIN AERATORS motor, seal assembly, float and
underwater power cable (referred to as in-water components) are covered under
warranty at 100% replacement cost should it fail due to defects in materials or
workmanship for a period of 3 years. This is in effect from the date of shipment,
when given normal and proper usage as determined by The Seller upon
examination, and when owned by the original user. All 1/2HP units have a similar 2
year warranty.
01/07Page 9
-
8/3/2019 011-011
10/3301/07
Page 10
-
8/3/2019 011-011
11/33
FIXED FOUNTAIN LIGHTING SYSTEMS AND OPTIONS SPECIFICATIONS
5.0 LIGHTING SYSTEM shall be _______ Volt, Model #(s)______________.
There are ______ total fixtures, containing ________________________
(clear or choose color(s): amber, blue, red, green or turquoise) lenses.
5.1 A total length of __________ feet of _______ gauge 3 conductor underwater power
cable is required. Two runs of cable may be required; reference cable sizing chart.
5.2 MULTI-PURPOSE ELECTRONIC LIGHT SYSTEM SEQUENCER shall be capable of
cycling light fixtures off and on, up to 6 programs. Yes____No____
5.3 A total length of __________ feet of _______ gauge, 4 conductor underwater power
cable is required for sequencer. Two runs of cable may be required.
5.4 LARGE CUSTOM INTAKE SCREEN (1-5HP) shall provide additional protected intake
area if Fixed Fountain will operate in a potentially high debris filled aquatic
environment. Yes ____ No _____
Please refer to TABLES 2 and 3 to assist in the completion of SECTION 5.
6.0 DESCRIPTION
A. Lamp housings shall be of Series 300 Stainless Steel construction. They
shall have a permanent Series 300 Stainless Steel electrical hub welded on the
bottom of the housing to allow electrical cable entry and be trunnion mounted to
cart framework for ease of light fixture adjustment.
B. Construction shall consist of nonmetallic Cord Connectors to prevent water
from entering the lamp housing. Lamp holders shall be double contact base
constructed of stainless steel with wires rated for a minimum of 105 degrees
Celsius. Reflectors shall be metal spun with Alzak finish for high reflectivity.
Lamps shall be high intensity, quartz halogen flood, double contact bayonet
base rated at 130VAC, mounted vertically.
C. Light fixture assembly shall consist of V shaped Lamp gaskets made of
silicon construction. Lens shall be of tempered glass with a clear non-diffusing
surface with a minimum of 5/32nd
thickness. Clamp ring shall be of Series 300
Stainless Steel. Fasteners and mounting hardware shall be of Series 300
stainless steel.
01/07Page 11
-
8/3/2019 011-011
12/33
D. Underwater Pin and Socket Connector shall consist of a Series 900, IP68
pin and socket connector. It shall be of a 3 pin (4 pin when a sequencer is used)
configuration rated 32 Amps at 600 VAC. The pin and socket ends shall each be
attached to a 30 piece of UL Listed underwater power cable rated at 600 Volts.
They both shall be permanently secured to their UL Listed power cables by a
integrated neoprene grommet and compression nut assembly. These assemblies
shall be epoxy filled to prevent entry of water or any other foreign matter. The
pin end assembly shall be permanently attached to the light housing with a
nonmetallic connector. This shall be potted using a flexible approved potting
compound. The underwater disconnect is a two piece molded assembly made of
glass reinforced nylon meeting UL 676 requirements. The socket end assembly
shall be permanently attached to the underwater disconnect cap end with a
nonmetallic connector. The body end of the underwater disconnect shall be
permanently attached to the power cable assembly with a nonmetallic
connector. Both cap and body ends shall be potted with an approved sealing
compound. The disconnect shall be sealed with an o-ring and by and external
Series 300 Stainless Steel clamp ring, which can be easily opened.
E. Safety Testing Lighting shall be tested and approved as a complete
assembly. This approval must meet Underwriters Laboratories Inc. requirements
in compliance with UL Category 676: Underwater Lighting Fixtures.
01/07Page 12
-
8/3/2019 011-011
13/3301/07
Page 13
-
8/3/2019 011-011
14/33
TABLE 1:CABLE SIZING CHARTS
MAXIMUM RECOMMENDED LENGTH FOR FOUNTAIN TO CONTROL PANEL
Single Phase 3 conductor 3 conductor Copper Wire Gauge Size
Unit Volts
Approx
Amps
#
14
#1
2
#1
0 #8 #6 #4 #2
1/2 HP 120 5.0
17
5 275 450 675
100
0 1700 2700
1/2 HP 208-240 2.5
55
0 875
140
0
220
0
350
0 5500 8000
4 conductor: Required on all 1 - 5HP Single Phase & ThreePhase Fountains
Single Phase 4 conductor 4 conductor Copper Wire Gauge Size
Unit Volts ApproxAmps #14 #12 #10 #8 #6 #4 #2
1 HP 120 18.0 -- -- 130 200 325 500 800
1 HP 208-240 9.0 -- 250 375 600
100
0 1500 2400
2 HP 208-240 12.0 -- 200 300 475 775 1200 1900
3.5 HP 208-240 15.0 -- -- 200 350 550 850 1350
5 HP 208-240 26.0 -- -- 150 250 400 650 1000
Three Phase 4 conductor 4 conductor Copper Wire Gauge Size
Unit VoltsApproxAmps
#14
#12
#10 #8 #6 #4 #2
1 HP 208-240 5.0 -- 450 700
120
0
180
0 3000 4800
1 HP 440-480 2.5 --
170
0
270
0
430
0
690
0
1100
0
1750
0
2 HP 208-240 6.0 -- 300 500 800
120
0 1900 3100
2 HP 440-480 3.0 --
110
0
175
0
280
0
445
0 7000
1120
0
3 HP 208-240 10.0 -- 250 400 650
100
0 1650 2600
3 HP 440-480 5.0 --
100
0
160
0
255
0
400
0 6400
1000
0
01/07Page 14
-
8/3/2019 011-011
15/33
5 HP 208-240 12.0 -- 150 250 400 600 950 1500
5 HP 440-480 6.0 -- 600 950
155
0
247
5 3900 6250
01/07Page 15
-
8/3/2019 011-011
16/33
TABLE 2: FIXED FOUNTAIN LIGHTING SYSTEMS
AQUAMASTER
FIXED FOUNTAINS are even more dramatic at night, with the addition of a
UL and cUL Listed NIGHT GLOW LIGHTING SYSTEM.
Any lighting system choice includes stainless steel lamp housings, ready to be installed,sealed with clear tempered glass lenses in a stainless steel clamp ring. Minimal
installation is required. All lights remain water-cooled and out of sight below the surface.
All necessary electrical controls, including timer, are pre-wired into the fountains existing
UL Listed control panel. Optional glass colored lenses (amber, blue, red, green or
turquoise), with or without an optional sequencer complete your dramatic aquatic display.
For uniformity of spray pattern coverage, 3 lights minimum is recommended.
1. LINE VOLTAGE: 120 Volt Lighting Systems
1/2 5 HP Fountain Lighting Systems available in 75, 150, or 250 watt fixtures
75 Watt Fixtures 1/2 HP
Units
Each system includes:
75 Watt Par 30 halogen flood lamps
50 of underwater cable
GFCI Protection
Timer
Clear lenses
UL andcUL Listing
2 light system: Model # 870352
3 light system: Model # 870353
4 light system: Model # 870354
75 Watt Fixtures 1- 5 HP
Units
2 light system: Model # 870322
3 light system: Model # 870323
4 light system: Model # 870324
150 Watt Fixtures 1/2 HP
Units
Each system includes:
150 or 250 Watt quartz halogenflood lamps
50 of underwater cable
GFCI Protection
Timer
Clear lenses
UL and cUL Listing
2 light system: Model # 870362
3 light system: Model # 870363
4 light system: Model # 870364
150 Watt Fixtures 1- 5 HP
Units
2 light system: Model # 870332
01/07Page 16
-
8/3/2019 011-011
17/33
3 light system: Model # 870333
4 light system: Model # 870334
250 Watt Fixtures 1/2 HP
Units
2 light system: Model # 870372
3 light system: Model # 870373
4 light system: Model # 870374
250 Watt Fixtures 1- 5 HP
Units
2 light system: Model # 870342
3 light system: Model # 870343
4 light system: Model # 870344
01/07Page 17
-
8/3/2019 011-011
18/33
TABLE 3: FIXED FOUNTAIN LIGHTING SYSTEMS (cont.)
CABLE SIZING CHART FOR LIGHTSMAXIMUM RECOMMENDED LENGTH FROM FOUNTAIN LIGHTS TO CONTROL
PANEL
3 Conductor Copper Wire Gauge Size
WattsPer
Fixture
# ofFixtures
Volts
Approx
Amps
#14
#12
#10
#8 #6 #4 #2
75 2 120 1.3750
1200
2000
3000
5000
8000
13000
75 3 120 1.9500 800
1300
2000
3300
5700 9000
75 4 120 2.5400 600
1000
1600
2500
4300 6900
150 2 120 2.5400 600
1000
1600
2500
4300 6900
150 3 120 3.8 250 400 650 1000 1650 2800 4500
150 4 120 5200 300 500 800
1200
2100 3400
250 2 120 4.2250 400 640
1000
1600
2500 4100
250 3 120 6.3160 260 420 675
1050
1700 2700
250 4 120 8.5100 200 300 500 750
1250 2000
CABLE SIZING CHART FOR LIGHTS WHEN ORDERED WITH A SEQUENCERMAXIMUM RECOMMENDED LENGTH FROM FOUNTAIN LIGHTS TO
CONTROL PANEL
3 & 4 Conductor see notes below Copper Wire Gauge SizeWatts Per
Fixture# of Fixtures
Volts
#14
#12
#10
#8 #6 #4 #2
75 3 or 4 120800
1200
2000
3200
5000 - -
75 6 (3 colors) 120400 600
1000
1600
2500 - -
75 8 (4 colors) 120400 600
1000
1600
2500 -
150 3 or 4 120400 600
1000
1600
2500
4300 -
150 6 (3 colors) 120200 300 500 800
1250
2150 -
150 8 (4 colors) 120200 300 500 800
1250
2150 -
250 3 or 4 120 25 400 650 100 160 26 -
01/07Page 18
-
8/3/2019 011-011
19/33
0 0 0 00
250 6 (3 colors) 120125 200 325 500 800
1300 -
250 8 (4 colors) 120125 200 325 500 800
1300
Lighting sequencer requires 2 runsof cable:
1) Sequencer with 3 colors require (1) run of 3 conductor cableand (1) run of 4 conductor cable2) Sequencer with 4 colors require (2) runs of4 conductor cable
P/Fixing of Glass Mosaic of approved shades of Zestha,Palladio, Bisazza make onlyincluding Chemical Adhesive(Bal Endura-Diamondstar), Grout Powder( Bal Endura-Diamondstar) complete in all respects including cleaning of the same as per Drawing
attached herewith showing the dimensions of each point.
Ripples Engineering Pvt. Ltd
C-119, Phase - II Extension, Noida (U.P)
Tel: 0120-2461911-15, Fax: 0120-2461910
Email: [email protected]
3153/R/PS/ 218
Dated 16/11/11
Gautam Banerjee
Bhopal IN
Kind Attn. : Mr. Gautam Banerjee
Subject :- Quote for the providing, fixing, testing & commissioning of water fetures
01/07Page 19
-
8/3/2019 011-011
20/33
Dear Sir,
Please find below our quote for the providing, fixing, testing & commissioning of water
features, based on the
drawings we received from you.
Remarks. : Wiring distance from water body sump to plant room/panel taken as 15m. as
per information available,
incase of change beyond 10% cost of wiring would change on pro-rata basis
Item Code Description Make/Brand Qty UoM Rate Amount
Water Body 1 : Providing, fixing, testing & commissioning of Geyser Jet Fountain (for 1.8
mtr. dia pool)
Providing, fixing, testing & commissioning of Nozzles
NOZ16.11 Geyser 25N (M.O.C Gunmetal - Noryl) Ripples 4 No 1,553.00 6,212.00 INR
NOZ16.12 Geyser 40N (M.O.C Gunmetal - Noryl) Ripples 1 No 2,329.00 2,329.00 INR
NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)
Adjustable Ripples Make
Ripples 3 No 225.00 675.00 INR
Providing, fixing, testing & commissioning of Lights
LED1.03 NL418LN/W Submersible LED Light - Warm
White 18W (6x3W LED's)
Ripples 11 No 4,169.00 45,859.00 INR
MOL1.42 Niche for NL 418LN - Nylon Ripples 11 No 230.00 2,530.00 INR
ELX2.20 Power Supply - 18V DC/15 Amp. (Make-
PE)
PE 1 No 10,120.00 10,120.00 INR
EL6.02 Junction Box 180/8 MOC Nylon MakeRipples
Ripples 2 No 978.00 1,956.00 INR
Providing, fixing, testing & commissioning of Suction inlet fittings
SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR
Providing, fixing, testing & commissioning of Dosing Unit
SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE
01/07Page 20
-
8/3/2019 011-011
21/33
Feeder)- Ripples
Ripples (Brand) 1 No 4,526.00 4,526.00 INR
Providing, fixing, testing & commissioning of Filter
SWA4.01 Sand/Bio Filter Top-mounted with 40mm
MPV (T 450-18") flow 8 m3/hr. - Ripples
Ripples (Brand) 1 No 19,323.00 19,323.00 INR
SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR
Providing, fixing, testing & commissioning of Pumps
OP8.07 Pump 3Hp Submersible 3 Phase
(SHOOL32TAE/65x65) C.G.
Crompton 1 No 21,758.00 21,758.00 INR
OP7.13 Pump 1Hp Submersible 1 Phase
(SHOEM12SAM30/32X25) C.G.
Crompton 1 No 13,854.00 13,854.00 INR
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 21
-
8/3/2019 011-011
22/33
Item Code Description Make/Brand Qty UoM Rate Amount
Providing, fixing, testing & commissioning of Control Panel
PNL2.05 Panel Body for Two Pump with
Transformer
Ripples 1 No 7,105.00 7,105.00 INR
PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR
PNL3.01 Starter for 3HP Submersible Pump Three
Phase
1 No 8,165.00 8,165.00 INR
PNL3.07 Starter for 1HP Submersible Pump Single
Phase
1 No 7,310.00 7,310.00 INR
Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including
Elbow, Tee, Socket
etc.
PL53.03 uPVC Pipe OD 32 (10 Kg.) Finolex/Prince/S
upreme
6 Mtr 58.00 348.00 INR
PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S
upreme
30 Mtr 135.00 4,050.00 INR
PL53.08 uPVC Pipe OD 90 (10 Kg.) Finolex/Prince/S
upreme
3 Mtr 428.00 1,284.00 INR
Providing & fixing of Valves, fittings etc of required size
PL5.06 Brass Ball Valve 40mm Imported 6 No 1,109.00 6,654.00 INR
PL5.04 Brass Ball Valve 25mm Imported 4 No 496.00 1,984.00 INR
PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INRPL47.03 MS Flange 40 NB - Threaded (for NRV
40mm )
2 No 235.00 470.00 INR
PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR
PL86.03 SS Nipple 25mm 4 No 275.00 1,100.00 INR
PL86.05 SS Nipple 40mm 1 No 365.00 365.00 INR
01/07Page 22
-
8/3/2019 011-011
23/33
Providing & fixing of Wires/cables including necessary accessories
EL29.80 Wire 2.5mm Three Core (Flat) Power
Lite/Everest
20 Mtr 154.00 3,080.00 INR
EL29.75 Wire 1.5mm Three Core (Flat) Power
Lite/Everest
20 Mtr 104.00 2,080.00 INR
EL29.116 Wire 1.5mm Two Core (Round) Power
Lite/Everest
50 mtr 71.00 3,550.00 INR
Providing and fixing of conduits, bends, fittings etc. of required size
PL60.02 PVC Conduit 20mm AKG/Sethia 20 Mtr 22.00 440.00 INR
PL60.03 PVC Conduit 25mm AKG/Sethia 70 Mtr 30.00 2,100.00 INR
PL60.04 PVC Conduit 32mm AKG/Sethia 20 Mtr 46.00 920.00 INR
Subtotal 188,538.00 INR
Water Body 2 : Providing, fixing, testing & commissioning of Dome Fountain (for 3.6 mtr.
dia pool)
Providing, fixing, testing & commissioning of Nozzles
NOZ26.13 Vertical Jet AF-20 -10mm bore Ripples 56 No 520.00 29,120.00 INR
NOZ26.10 Vertical Jet AF-40 -19mm bore Ripples 1 No 4,016.00 4,016.00 INR
NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)
Adjustable Ripples Make
Ripples 3 No 225.00 675.00 INR
Providing, fixing, testing & commissioning of Ring 3.6 mtr. dia
NOZ33.05 GI Ring 65NB (Per Linear Meter) Ripples 11.31 Mtr 1,086.00 12,282.66 INR
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 23
-
8/3/2019 011-011
24/33
Item Code Description Make/Brand Qty UoM Rate Amount
Providing, fixing, testing & commissioning of Lights
LED1.02 SL418LN/W Submersible LED Light - Warm
White 18W (6x3W LED's)
Ripples 17 No 4,169.00 70,873.00 INR
ELX2.20 Power Supply - 18V DC/15 Amp. (Make-
PE)
PE 1 No 10,120.00 10,120.00 INR
EL6.02 Junction Box 180/8 MOC Nylon Make
Ripples
Ripples 3 No 978.00 2,934.00 INR
EL13.12 SS Light Stand 3 Way 40 NB Ripples 1 No 500.00 500.00 INR
Providing, fixing, testing & commissioning of Pumps
OP7.13 Pump 1Hp Submersible 1 Phase
(SHOEM12SAM30/32X25) C.G.
Crompton 1 No 13,854.00 13,854.00 INR
OP7.05 Pump 2HP Submersible 1 Phase
(OSK22/50x40) C.G. Discharge -305 LPM
@ 10.5mtr. Head, Starting-DOL
Crompton 1 No 18,400.00 18,400.00 INR
OP8.44 Pump 5HP Submersible 3 Phase
(OSQ52/80X80) C.G.
Crompton 2 No 23,895.00 47,790.00 INR
Providing, fixing, testing & commissioning of Suction inlet fittings
SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR
Providing, fixing, testing & commissioning of Dosing Unit
SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE
Feeder)- RipplesRipples (Brand) 1 No 4,526.00 4,526.00 INR
Providing, fixing, testing & commissioning of Filter
SWA4.01 Sand/Bio Filter Top-mounted with 40mm
MPV (T 450-18") flow 8 m3/hr. - Ripples
Ripples (Brand) 1 No 19,323.00 19,323.00 INR
SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR
01/07Page 24
-
8/3/2019 011-011
25/33
Providing, fixing, testing & commissioning of Control Panel
PNL2.09 Panel Body for Four Pump with
Transformer
Ripples 1 No 15,496.00 15,496.00 INR
PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR
PNL3.09 Starter for 2HP Submersible Pump Single
Phase
1 No 8,120.00 8,120.00 INR
PNL3.07 Starter for 1HP Submersible Pump Single
Phase
1 No 7,310.00 7,310.00 INR
PNL3.02 Starter for 5HP Submersible Pump Three
Phase
2 No 10,284.00 20,568.00 INR
Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including
Elbow, Tee, Socket
etc.
PL53.06 uPVC Pipe OD 63 (10 Kg.) Finolex/Prince/S
upreme
15 Mtr 212.00 3,180.00 INR
PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S
upreme
40 Mtr 135.00 5,400.00 INR
PL53.13 uPVC Pipe OD 140 (10 Kg.) Finolex/Prince/S
upreme
3 Mtr 1,070.00 3,210.00 INR
Providing & fixing of Valves, fittings etc of required size
PL5.06 Brass Ball Valve 40mm Imported 9 No 1,109.00 9,981.00 INR
PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INRPL47.03 MS Flange 40 NB - Threaded (for NRV
40mm )
2 No 235.00 470.00 INR
PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR
PL86.05 SS Nipple 40mm 1 No 365.00 365.00 INR
01/07Page 25
-
8/3/2019 011-011
26/33
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 26
-
8/3/2019 011-011
27/33
Item Code Description Make/Brand Qty UoM Rate Amount
Providing & fixing of Wires/cables of various sizes including necessary accessories
EL29.75 Wire 1.5mm Three Core (Flat) Power
Lite/Everest
45 Mtr 104.00 4,680.00 INR
EL29.116 Wire 1.5mm Two Core (Round) Power
Lite/Everest
90 mtr 71.00 6,390.00 INR
EL29.80 Wire 2.5mm Three Core (Flat) Power
Lite/Everest
45 Mtr 154.00 6,930.00 INR
Providing and fixing of conduits, bends, fittings etc. of required size
PL60.02 PVC Conduit 20mm AKG/Sethia 50 Mtr 22.00 1,100.00 INR
PL60.03 PVC Conduit 25mm AKG/Sethia 135 Mtr 30.00 4,050.00 INR
Subtotal 340,054.66 INR
Water Body 3 (Arc Shape Water Body) : Providing, fixing, testing & commissioning of
Geyser Jet Fountain
Providing, fixing, testing & commissioning of Nozzles
NOZ16.11 Geyser 25N (M.O.C Gunmetal - Noryl) Ripples 20 No 1,553.00 31,060.00 INR
NOZ13.08 Floor Inlet Nozzle (ABS)(3 PCs./Set)
Adjustable Ripples Make
Ripples 4 No 225.00 900.00 INR
Providing, fixing, testing & commissioning of Lights
LED1.18 NL409LN/W Submersible LED Light Warm
White 9W (3X3W LEDs)
Ripples 40 No 1,898.00 75,920.00 INR
MOL1.52 Niche for NL409LN Nylon Ripples 40 No 173.00 6,920.00 INR
ELX2.19 Power Supply - 9V DC/15 Amp. (Make PE)PE 2 No 5,951.00 11,902.00 INR
EL6.02 Junction Box 180/8 MOC Nylon Make
Ripples
Ripples 8 No 978.00 7,824.00 INR
Providing, fixing, testing & commissioning of Suction inlet fittings
SWA2.240 Suction Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR
01/07Page 27
-
8/3/2019 011-011
28/33
SWA2.40 Vacuum Point (2 Pcs./Set)ABS(Ripples) Ripples 1 No 184.00 184.00 INR
Providing, fixing, testing & commissioning of Dosing Unit
SWA4.09 Chlorine/ Bromine Dosing Unit (IN-LINE
Feeder)- Ripples
Ripples (Brand) 1 No 4,526.00 4,526.00 INR
Providing, fixing, testing & commissioning of Filter
SWA4.01 Sand/Bio Filter Top-mounted with 40mm
MPV (T 450-18") flow 8 m3/hr. - Ripples
Ripples (Brand) 1 No 19,323.00 19,323.00 INR
SWA2.18 Sand for Sand Filter (SIZE 16/32 Mesh) 50 Kg 14.00 700.00 INR
Providing, fixing, testing & commissioning of Pumps
OP8.44 Pump 5HP Submersible 3 Phase
(OSQ52/80X80) C.G.
Crompton 2 No 23,895.00 47,790.00 INR
OP7.13 Pump 1Hp Submersible 1 Phase
(SHOEM12SAM30/32X25) C.G.
Crompton 1 No 13,854.00 13,854.00 INR
Providing, fixing, testing & commissioning of Control Panel
PNL2.07 Panel Body for Three Pump with
Transformer
Ripples 1 No 11,742.00 11,742.00 INR
PNL3.14 Three Phase Panel Incomer 1 No 6,506.00 6,506.00 INR
PNL3.07 Starter for 1HP Submersible Pump Single
Phase
1 No 7,310.00 7,310.00 INR
PNL3.02 Starter for 5HP Submersible Pump Three
Phase
2 No 10,284.00 20,568.00 INR
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 28
-
8/3/2019 011-011
29/33
Item Code Description Make/Brand Qty UoM Rate Amount
Providing and fixing of pipes (uPVC pipe- 10kg. Pressure) & fittings (Heavy) including
Elbow, Tee, Socket
etc.
PL53.13 uPVC Pipe OD 140 (10 Kg.) Finolex/Prince/S
upreme
12 Mtr 1,070.00 12,840.00 INR
PL53.08 uPVC Pipe OD 90 (10 Kg.) Finolex/Prince/S
upreme
12 Mtr 428.00 5,136.00 INR
PL53.03 uPVC Pipe OD 32 (10 Kg.) Finolex/Prince/S
upreme
12 Mtr 57.00 684.00 INR
PL53.05 uPVC Pipe OD 50 (10 Kg.) Finolex/Prince/S
upreme
60 Mtr 135.00 8,100.00 INR
Providing & fixing of Valves, fittings etc of required size
PL5.06 Brass Ball Valve 40mm Imported 6 No 1,109.00 6,654.00 INR
PL5.04 Brass Ball Valve 25mm Imported 20 No 496.00 9,920.00 INR
PL10.12 NRV - 40mm (Flap/Wafer Type - C.I.) Quin/Krishna 1 No 704.00 704.00 INR
PL47.03 MS Flange 40 NB - Threaded (for NRV
40mm )
2 No 235.00 470.00 INR
PL86.03 SS Nipple 25mm 20 No 275.00 5,500.00 INR
PL28.05 GI Nipple 40 NB 3 No 99.00 297.00 INR
Providing & fixing of Wires/cables of various sizes including necessary accessories
EL29.75 Wire 1.5mm Three Core (Flat) Power
Lite/Everest25 Mtr 104.00 2,600.00 INR
EL29.116 Wire 1.5mm Two Core (Round) Power
Lite/Everest
300 mtr 71.00 21,300.00 INR
EL29.80 Wire 2.5mm Three Core (Flat) Power
Lite/Everest
01/07Page 29
-
8/3/2019 011-011
30/33
60 Mtr 154.00 9,240.00 INR
Providing and fixing of conduits, bends, fittings etc. of required size
PL60.02 PVC Conduit 20mm AKG/Sethia 100 Mtr 22.00 2,200.00 INR
PL60.03 PVC Conduit 25mm AKG/Sethia 325 Mtr 30.00 9,750.00 INR
PL60.04 PVC Conduit 32mm AKG/Sethia 60 Mtr 46.00 2,760.00 INR
Subtotal 365,368.00 INR
Pool Cleaning Kit
SWA4.30 Vaccum Hose 50 Ft. Spiral Wound EVA Dia.
40mm - Ripples
Ripples (Brand) 1 No 8,965.00 8,965.00 INR
SWA4.08 Leaf Skimmer - Standard Ripples Ripples (Brand) 1 No 391.00 391.00 INR
SWA4.07 Brush Curved 18"/45cm. (Standard
Polybristle Wall Brush) - Ripples
Ripples (Brand) 1 No 695.00 695.00 INR
SWA4.06 Vacuum Head Deluxe Triangular
Transparent Cast Iron Weighted - Ripples
Ripples (Brand) 1 No 2,958.00 2,958.00 INR
SWA4.05 Telescopic pole 2x120cm. - 0.8mm Thick Al.
Tubbing white -2.5mtr Long - Ripples
Ripples (Brand) 1 No 1,628.00 1,628.00 INR
Subtotal 14,637.00 INR
PAF1.05 Packing & Forwading Charges 1 No 16,000.00 16,000.00 INR
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 30
-
8/3/2019 011-011
31/33
Item Code Description Make/Brand Qty UoM Rate Amount
OS1.02 Outstation charges- (Boarding, lodging &
travel cost of our project teams).
1 No 32,000.00 32,000.00 INR
Summary of Cost
Tax
Grand Total
129,011.79 INR
1,085,609.45 INR
EXCLUSIONS:
Safe custody of material at site.
Providing necessary power supply near the Control Panel
Earthing work required for the fountain equipment.
Civil work if any.
Providing inlet and drain for the water body
TERMS AND CONDITIONS OF CONTRACT:
Price : FOR Site.
Payment : 35% Advance along with order, 50% On completion of plumbing & conduiting
work within the water
body and Prior to dispatch of capital material & 15% on Completion
Warranty : One Year from date of commisioning.Validity : One Month from date of Quote
Delivery : 8-10 weeks from date of order and Advance.
Taxes : Included (CST @ 13.5% on 80% of value & Service Tax @ 3.40% on 100% of value)
Note : (i) Tax not applicable on packing forwarding & outstation charges
01/07Page 31
-
8/3/2019 011-011
32/33
We hope our quote is in line with your requirement. Should you need any further
information / clarifications please
feel free to contact us.
We look forward to receiving your valued order.
Yours truly,
For Ripples Engineering Pvt Ltd
Pankaj Sharma
(Sr. Sales Officer)
Mob : 9350001909
Email : [email protected]
REGD. OFFICE:G-36, Green Park Main Mkt., New Delhi-110016, Ph. : +91-11-26524682,
26856164, Fax: 26855645
E-mail: [email protected]
01/07Page 32
-
8/3/2019 011-011
33/33