نسخة من trouble codes copystar-kyocera_blackcat4866
TRANSCRIPT
Model Error Code DescriptionC0030
FS-1128MFP C0070
C0100
C0120
C0130
C0140
C0150
C0170
C0180
C0420
FS-1128MFP C0830
FS-1128MFP C0840
FS-1128MFP C0870
FS-1128MFP (2H92JN)
Fax Control PWB System Problem. Processing with the optional fax software was disabled due to a hardware problem.
Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software.
FS-1028MFP, FS-1128MFP
Backup Memory Device Error. Defective flash memory or defective control PWB.
FS-1028MFP, FS-1128MFP
MAC Address Data Error. Defective flash memory.
FS-1028MFP, FS-1128MFP
Backup Memory Read/Write Error. Defective flash memory or defective control PWB.
FS-1028MFP, FS-1128MFP
Backup Memory Data Error. Defective flash memory or defective control PWB.
FS-1028MFP, FS-1128MFP
Control PWB EEPROM Error. Detecting control PWB EEPROM (U17) communication error.
FS-1028MFP, FS-1128MFP
Billing Counting Error. Defective control PWB or its EEPROM (U17).
FS-1028MFP, FS-1128MFP
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.
FS-1028MFP, FS-1128MFP
Paper Feeder Communication Error. Communication error between the control PWB and optional paper feeder.
Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
Faults of RTC. The time is judged to go back based on the comparison of the RTC time and the current time, or (5) years or more have passed.
Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High-capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried several times.
FS-1128MFP C0920
C2000
C2610
C2620
C3100
C3200
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB.
FS-1028MFP, FS-1128MFP
Main Motor Error. The main motor ready input is not given for 2 sec, after the main drive motor has turned On.
FS-1028MFP, FS-1128MFP
PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 1)
FS-1028MFP, FS-1128MFP
PF-100 Paper Feeder Motor Error. The PF paper feed motor ready input is not given for 2 sec, after the PF paper feed drive motor has turned On. (Optional paper feeder 2)
FS-1028MFP, FS-1128MFP
ISU Home Position Error. Home position is not correct when power is turned On, or copying a document from the contact glass.
FS-1028MFP, FS-1128MFP
Exposure Lamp Error. The exposure lamp is not turned On.
C3300
C3500
C4000
C4200
C6000
C6020
C6030
C6400
C7990
F000
FS-1028MFP, FS-1128MFP
AGC Error. After AGC the correct input is not obtained at the CCD.
FS-1028MFP, FS-1128MFP
CPU-ASIC (CCD PWB) Communication Error. An error code is detected.
FS-1028MFP, FS-1128MFP
Polygon Motor Error. Polygon motor ready input is not given for 6 sec while the polygon motor is On.
FS-1028MFP, FS-1128MFP
Beam Detect Error. BD sensor does not detect the laser beam.
FS-1028MFP, FS-1128MFP
Broken Fuser Heater Wire. The temperature does not rise after the fuser heater lamp is turned On.
FS-1028MFP, FS-1128MFP
Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects abnormally high temperature.
FS-1028MFP, FS-1128MFP
Broken Fuser Thermistor Wire.Input from fuser thermistor is 0 (A/D value).
FS-1028MFP, FS-1128MFP
Zero-Cross Signal Error. The zero cross signal does not reach the control PWB for a specified time.
FS-1028MFP, FS-1128MFP
Waste Toner Full. The waste toner sensor has detected that the waste toner reservoir (drum unit) is full.
FS-1028MFP, FS-1128MFP
Control PWB-Operation panel PWB comunication error.
F020
F040
F041
F050
F186 Control PWB Video Data Control Error.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1028MFP, FS-1128MFP
Control PWB RAM Checksum Error. Defective main RAM on the control PWB or defective expanded memory DIMM.
FS-1028MFP, FS-1128MFP
Control PWB Engine Communication Error.
FS-1028MFP, FS-1128MFP
Control PWB-Scanner PWB Communication Error. A communication error is detected.
FS-1028MFP, FS-1128MFP
Control PWB Engine Checksum Error. Some error may have occurred while downloading firmware, or defective control PWB.
FS-1028MFP, FS-1128MFP
E00000 or U00000
Fax Communication Error: No response or line busy after the set number of redials.
E00100 or U00100
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
E00200 or U00200
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
E00300 or U00300
Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E00431 or U00431
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00431 or U00431
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
E00432 or U00432
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
E00432 or U00432
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
E00433 or U00433
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
E00433 or U00433
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E00440 or U00440
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
E00441 or U00441
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
E00450 or U00450
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
E00462 or U00462
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
E00600 or U00600
Fax Communication Error: The document processor cover is open.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP Fax Communication Error: System error.
FS-1128MFP
FS-1128MFP
FS-1128MFP
E00601 or U00601
Fax Communication Error: Document jam or the document length exceeds the maximum.
E00602 or U00602
Fax Communication Error: Image scanning section problem.
E00603 or U00603
Fax Communication Error: No document feed.
E00604 or U00604
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
E00610 or U00610
Fax Communication Error: Recording section cover open.
E00611 or U00611
Fax Communication Error: Recording paper jam.
E00613 or U00613
Fax Communication Error: Image writing section problem.
E00614 or U00614
Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615
Fax Communication Error: Empty of recording paper.
E00620 or U00620
Fax Communication Error: Copier fixing unit problem.
E00622 or U00622
Fax Communication Error: Copier drive motor problem.
E00655 or U00655
Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
E00670 or U00670
Fax Communication Error: Power was cut off during communication.
E00677 or U00677
Fax Communication Error: There was no file to transmit in the memory transmission mode.
E00690 or U00690
E00700 or U00700
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
E00800 or U00800
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E00900 or U00900
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
E00910 or U00910
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01013 or U01013
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
E01014 or U01014
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01019 or U01019
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
E01020 or U01020
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
E01021 or U01021
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
E01022 or U01022
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01026 or U01026
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01027 or U01027
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01028 or U01028
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
E01040 or U01040
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
E01044 or U01044
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E010x45 or U01045
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
E01046 or U01046
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
E01047 or U01047
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
E01048 or U01048
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
E01052 or U01052
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01054 or U01054
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
E01055 or U01055
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
E01056 or U01056
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
E01057 or U01057
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
E01072 or U01072
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brake in loop current was detected during transmission.
E01073 or U01073
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
E01080 or U01080
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01091 or U01091
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E01100 or U01100
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
E01110 or U01110
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
E01111 or U01111
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
E01112 or U01112
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01113 or U01113
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
E01114 or U01114
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
E01115 or U01115
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
E01119 or U01119
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
E01120 or U01120
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
E01121 or U01121
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
E01122 or U01122
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01123 or U01123
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
E01124 or U01124
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
E01129 or U01129
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
E01140 or U01140
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
E01141 or U01141
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
E01142 or U01142
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01143 or U01143
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
E01148 or U01148
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
E01149 or U01149
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIP signal.
E01150 or U01150
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
E01151 or U01151
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01152 or U01152
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RNR signal (ECM).
E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
E01161 or U01161
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
E01162 or U01162
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
E01163 or U01163
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
E01164 or U01164
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01170 or U01170
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
E01191 or U01191
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
E01400 or U01400
Fax Communication Error: An invalid one-touch key was specified during communication.
E01500 or U01500
Fax Communication Error: A communication error occurred when calling in V.8 mode.
E01600 or U01600
Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01720 or U01720
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E01721 or U01721
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E01821 or U01821
Fax Communication Error: Operation was interrupted due to the absence of a common communication speed between units. (including when an impossible combination of communication speed and symbol speed occurs) after MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut.
E02000 or U02000
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
E02100 or U02100
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
E02303 or U02303
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
E02304 or U02304
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E02400 or U02400
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
E03000 or U03000
Fax Communication Error: No document was present in the destination unit when polling reception started.
E03100 or U03100
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
E03200 or U03200
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
E03200 or U03200
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03300 or U03300
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
E03500 or U03500
Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination.
E03500 or U03500
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500
Fax Communication Error: The destination was being accessed.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E03600 or U03600
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
E03600 or U03600
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
E03700 or U03700
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
E03700 or U03700
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
E04000 or U04000
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: The destination was being accessed.
E04100 or U04100
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
E04200 or U04200
Fax Communication Error: In encrypted transmission, the specified encryption box was not registered in the destination unit.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
E04300 or U04300
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
E04400 or U04400
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
E04401 or U04401
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
E04500 or U04500
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
E05000 or U05000
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
E09000 or U09000
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
FS-1128MFP
message "Add Toner."
message
message "Cannot duplex print on this paper."
E12000 or U12000
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
E12000 or U12000
Fax Communication Error: In subaddress-based relay reception memory overflowed.
E12100 or U12100
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
E14000 or U14000
Fax Communication Error: Memory overflowed during confidential reception.
E14000 or U14000
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
E19000 or U19000
Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100
Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
E19400 or U19400
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
"Cannot connect to Authentication Server."
FS-1028MFP, FS-1128MFP
message "Cannot send fax."
message "Close Document Processor."
message "Close front cover."
message
message "File is not found. Job is cancelled."
message "Incorrect account ID. Job is cancelled."
message "Incorrect account ID."
message
message
message
message
message
message "Load paper in MP Tray"
message "Load paper to cassette 1"
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
"Error occurred. Turn the main power switch off and on. C####"
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
"Incorrect Login User Name or Password. Job is cancelled."
FS-1028MFP, FS-1128MFP
"Insufficient memory. Cannot start the job."
FS-1028MFP, FS-1128MFP
"Job Accounting restriction exceeded. Cannot print."
FS-1028MFP, FS-1128MFP
"Job Accounting restriction exceeded. Cannot scan."
FS-1028MFP, FS-1128MFP
"Job Accounting restriction exceeded. Job is cancelled."
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
message "Machine failure. Call service. C####"
message
message "Paper jammed."
message "Place original and press Start key."
message
message
message "Send error. ####"
FS-1128MFP message
message
message
message "Unknown toner installed. PC"
message "Unknown toner installed."
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
"Memory is full. Print job cannot be processed completely."
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
"Remove original from Document Processor."
FS-1028MFP, FS-1128MFP
"Scanner memory is full. Job is cancelled."
FS-1028MFP, FS-1128MFP
"Sub address/Polling box limit exceeded. Job is cancelled."
FS-1028MFP, FS-1128MFP
"The phone receiver is off the hook. Hang up."
FS-1028MFP, FS-1128MFP
"Top tray is full of Paper. Remove the paper."
FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
message "USB memory error. Job is cancelled."FS-1028MFP, FS-1128MFP
FS-1028MFP, FS-1128MFP
Send Error 1101
Error: FTP Host Name. Enter the disable host name/IP address.
FS-1028MFP, FS-1128MFP
Send Error 1101
Error: Host Name. SMTP server name is not set. Error SMTP server name.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable SMB shared name.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable SMB user/password.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign the SMB user who is not allowed to access the folder.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB host name error.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password. Assign disable FTP user/password.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password. FTP domain name is not entered.
FS-1028MFP, FS-1128MFP
Send Error 1102
Error: Username/Password. User ID for email authentication is not entered or entered wrongly. Wrong authentication password is entered.
FS-1028MFP, FS-1128MFP
Send Error 1103
Error: Pathname or File Name. Assign disable FTP folder path.
FS-1028MFP, FS-1128MFP
Send Error 1103
Error: Pathname or File Name. Assign disable SMB folder path.
FS-1028MFP, FS-1128MFP
Send Error 1103
Error: Pathname or File Name. Connection to the FTP folder which is not permitted for reference/writing.
FS-1028MFP, FS-1128MFP
Send Error 1103
Error: Pathname or File Name. Connection to the SMB folder which is not permitted for reference/writing.
FS-1028MFP, FS-1128MFP
Send Error 1103
Error: Pathname or File Name. SMB domain name is not entered.
FS-1028MFP, FS-1128MFP
Send Error 1104
Error: No Recipient Address. The destination email address is not specified.
FS-1028MFP, FS-1128MFP
Send Error 1105
Error: Not Supported Protocol. FTP protocol is set to OFF.
FS-1028MFP, FS-1128MFP
Send Error 1105
Error: Not Supported Protocol. SMB protocol is set to OFF.
FS-1028MFP, FS-1128MFP
Send Error 1105
Error: Not Supported Protocol. SMTP protocol is set to OFF.
FS-1028MFP, FS-1128MFP
Send Error 1106
Error: No Sender Info. Sender email address is not entered.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Assign the wrong FTP port number.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Assign the wrong SMB port number.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Enter the disable FTP host name/IP address.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Enter the disable SMB host name/IP address.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Network FTP is not connected.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Network SMB is not connected.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Network SMTP is not connected.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
FS-1028MFP, FS-1128MFP
Send Error 2101
Error: Can Not Connect. The specified server is not SMTP server.
FS-1028MFP, FS-1128MFP
Send Error 2102
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
FS-1028MFP, FS-1128MFP
Send Error 2102
Error: Cannot Connect With Timeout. The FTP server is unable to communicate.
FS-1028MFP, FS-1128MFP
Send Error 2102
Error: Cannot Connect With Timeout. The SMTP server is unable to communicate.
FS-1028MFP, FS-1128MFP
Send Error 2103
Error: Response Wait With Timeout. The FTP server is unable to communicate.
FS-1028MFP, FS-1128MFP
Send Error 2103
Error: Response Wait With Timeout. The SMB server is unable to communicate.
FS-1028MFP, FS-1128MFP
Send Error 2103
Error: Response Wait With Timeout. The SMTP server is unable to communicate.
FS-1028MFP, FS-1128MFP
Send Error 2201
Error: FTP Network Transfer. Error occurs on the network.
FS-1028MFP, FS-1128MFP
Send Error 2201
Error: SMB Network Transfer. Error occurs on the network.
FS-1028MFP, FS-1128MFP
Send Error 2201
Error: SMTP Network Transfer. Error occurs on the network.
FS-1028MFP, FS-1128MFP
Send Error 2202
Error: FTP Network Transfer With Timeout. Error occurs on the network.
FS-1028MFP, FS-1128MFP
Send Error 2202
Error: SMTP Network Transfer With Timeout. Error occurs on the network.
FS-1028MFP, FS-1128MFP
Send Error 2202
Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time.
FS-1028MFP, FS-1128MFP
Send Error 2202
Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time.
FS-1028MFP, FS-1128MFP
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the FTP server, above specified time.
FS-1028MFP, FS-1128MFP
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the SMB server, above specified time.
FS-1028MFP, FS-1128MFP
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the SMTP server, above specified time.
FS-1028MFP, FS-1128MFP
Send Error 2204
Error: Email Size Limit. The size of the email attachment exceeds its limit.
FS-1028MFP, FS-1128MFP
Send Error 3101
Error: Server Response. SMTP server setting is not authenticated normally.
FS-1028MFP, FS-1128MFP
Send Error 3101
Error: Server Response. The FTP server is error status.
FS-1028MFP, FS-1128MFP
Send Error 3101
Error: Server Response. The SMTP server is error status.
FS-1028MFP, FS-1128MFP
Send Error 3201
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism found.
FS-1028MFP, FS-1128MFP
Send Error 5101
Error: Send Software Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
FS-1028MFP, FS-1128MFP
Send Error 5102
Error: Send Software Already Connected. Operation handle error. Error for stored status in the operation handle.
FS-1028MFP, FS-1128MFP
Send Error 5103
Error: Send Software Not Yet Opened. Error for storage status in the operation handle.
FS-1028MFP, FS-1128MFP
Send Error 5104
Error: Send Software Already Opened. Error for storage status in the operation handle.
FS-1028MFP, FS-1128MFP
Send Error 7101
Error: Send Software Memor Allocation. Insufficient memory space.
FS-1028MFP, FS-1128MFP
Send Error 7102
Error: Send Software Socket Create. Unable to create a communication socket.
FS-1028MFP, FS-1128MFP
Send Error 720f
Error: Send Software Unknown Error. Unable to determine the cause.
FS-1028MFP, FS-1128MFP
Send Error 9181
Error: Email page Max Count Over. The number of pages of a send file exceeds 999 pages.
FS-1028MFP, FS-1128MFP
Send Error 9181
Error: FTP page Max Count Over. The number of pages of a send file exceeds 999 pages.
FS-1028MFP, FS-1128MFP
Send Error 9181
Error: SMB page Max Count Over. The number of pages of a send file exceeds 999 pages.
FS-1028MFP, FS-1128MFP
Send Error 9181
Error: TWAIN page Max Count Over. The number of pages of a send file exceeds 999 pages.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Press OK key.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Turn power Off/On.
Turn power Off/On.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Service Checks1) Repl fax control PWB.
1) Replace the control PWB.
1) Replace the control PWB.
1) Replace the control PWB.
1) Replace the control PWB.
1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.
1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.
1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB.
1) Check the installation or replace the control PWB EEPROM (U17), 2) Repl control PWB, 3) Repl engine PWB.
1) Incorrect installation-reinstall, 2) Reseat YC30 @ control PWB & paper feeder interface connector, 3) Reseat YC5 @ control PWB & paper feeder interface connector, 4) Repl interface harness, 5) Repl control PWB, 6) Repl PF main PWB.
1) Upgrade firmware to compatible versions, 2) Repl fax control PWB.
1) Reinstall the backup battery on the fax control PWB, 2) Repl fax control PWB.
1) Reinstall the fax control PWB, 2) Repl fax control PWB, 3) Repl control PWB.
1) Repl fax control PWB.
1) Reseat drive motor connector CN1 & control PWB connector YC17, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl main motor, 5) Repl control PWB.
1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.
1) Reseat PF paper feed motor connector & PF main PWB connector YC4, 2) Pinout or replace harness, 3) Check drive components for excessive drag, 4) Repl PF paper feed motor, 5) Repl control PWB.
1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between ISU motor & YC104 @ scanner PWB, 4) Replace FFC from YC6 to YC103, 5) Replace FFC from ISU motor to YC104, 6) Check/repl scanner HPS, 7) Check scanner drive components for excessive drag, 8) Repl scanner motor, 9) Repl image scanner unit (ISU).
1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Reseat FFC between YC6 @ control PWB & YC103 @ scanner PWB, 3) Reseat FFC between YC3 @ CCD PWB & YC101 @ inverter PWB, 4) Reseat FFC between YC102 @ inverter PWB & exposure lamp, 5) Replace FFC from YC6 to YC103, 6) Replace FFC from YC3 to YC101, 7) Replace FFC from inverter to exposure lamp, 8) Repl exposure lamp, 9) Repl inverter PWB, 10) Repl image scanner unit (ISU).
1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).
1) Reseat flexible flat cable (FFC) between YC1 @ CCD PWB & YC8 @ control PWB, 2) Repl exposure lamp, 3) Repl CCD PWB, 4) Repl control PWB, 5) Repl image scanner unit (ISU).
1) Reseat polygon motor connector & YC10 @ control PWB, 2) Repl polygon motor harness, 3) Repl laser unit, 4) Repl control PWB.
1) Possible condensation on polygon mirror. Clean or repl laser unit. 2) Reseat laser unit connectors, 3) Repl laser unit, 4) Repl control PWB.
1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
1) Ohm out thermistor. If 0 ohms replace, 2) Repl control PWB.
1) Reseat thermistor & heat lamp connections, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC202 @ high voltage PWB & YC23 @ control PWB, 3) Reseat YC103 @ PSU & YC201 @ high voltage PWB, 4) Repl harness from YC202 to YC23, 5) Repl harness from YC103 to YC201, 6) Check YC103-8 @ PSU for zero-crossing signal. If absent repl PSU, 4) If zero-crossing signal is present repl control PWB.
1) Shake process unit side to side, then power Off/On, 2) Repl drum unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl control PWB.
1) Reseat YC1 @ operation panel PWB & YC7 @ control PWB, 2) Repl harness from YC1 to YC7, 3) Repl operation panel PWB, 4) Replace control PWB.
Load paper.
1) Power Off/On, 2) Repl expanded memory DIMM, 3) Replace control PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace control PWB, 3) Repl scanner PWB. Contact Service Administrative Division.
1) Reload current firmware, 2) Power Off/On, 3) Replace control PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace control PWB. Contact Service Administrative Division.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
1) Replace toner container.
1) Check registration to Authentication server. 2) Check password and computer address for Authentication Server. 3) Check connection to network.
1) To print without using duplex press OK. 2) Select the available paper type.
1) Cord connected? Check phone cord. 2) Is the permitted fax # or permitted ID # registered correctly? Check. 3) Has a communication error occurred? See above. 4) Is the destination fax line busy? Send again. 5) Does the destination fax machine respond? Send again. 6) Is there an error other than above? See above.
1) The document processor is still open even though an original has been inserted. Close the document processor. 2) Close the top cover of the document processor.
1) The top cover or the front cover is open. Close the covers securely.
1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
1) The specified file is not found. The job is cancelled. Press the OK key.
1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
1) The Account ID does not match. Check the registered Account ID.
1) Enter the correct login user name or password.
1) Further scanning cannot be performed due to insufficient memory. Press the OK key to print the scanned pages. Press the Cancel key to cancel the printing job.
1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
1) This job is cancelled because it is restricted by Job Accounting. Press the OK key.
1) The printing count exceeded the acceptable count restricted by Job Accounting. Cannot print any more. This job is cancelled. Press the OK key.
1) The paper has run out. Add paper to the paper source.
1) The paper has run out. Add paper to the paper source, 2) The cassette is not properly closed. Be sure the cassette it closed securely.
1) See below:
1) Put down the receiver.
1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
1) Unable to continue the job as the memory is used up. Press the OK key to print the scanned pages. The print job cannot be processed completely. Press the Cancel key to cancel the job.
1) If a paper jam occurs the machine will stop and the location of the jam will be indicated on the Message Display. Leave the machine On and follow the instructions to removed the jammed paper.
1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.
1) Remove originals from the document processor, put them back in their original order, and place them again. Press the Start key to resume printing. Press the Cancel key to cancel the job.
1) Scanning cannot be performed due to insufficient memory of scanner. The job is cancelled. Press the OK key.
1) Fax box is full and no further storage is available. The job is cancelled. Press the OK key.
1) Remove the paper from the top tray, and press the OK key to resume the job.
1) This message is displayed if the installed toner container's regional specification does not match the machine's.
1) If the toner container was taken from a different machine of the same model while it was displaying the Add Toner message, ignore the message and use the toner.
1) This job is cancelled. Press the OK key.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter the correct username/password.
Enter correct folder path.
Enter correct folder path.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Enter the correct username/password. Check the access limit of destination folder.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Scan folder is not shared out to the network properly.
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Enter the correct username/password. Check the access limit of destination folder.
Specify the destination address.
Enter the correct port number.
Enter the correct port number.
Enter the correct host name or IP address.
Enter the correct host name or IP address.
Select valid POP3 user other than [Other].
Enter the correct username/password. Check the access limit of destination folder.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct host name or IP address.
Check if the server is operating properly.
Check if the server is operating properly.
Check is the server is operating properly.
Check is the server is operating properly.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Check is the server is operating properly.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication mechanism.
Model Error Code DescriptionCS-1820 (2GM) C0030
CS-1820 C0070
CS-1820 C0150
CS-1820 C0160
CS-1820 C0170
CS-1820 C0180
CS-1820 C0210
CS-1820 C0220
CS-1820 C0280
CS-1820 C0800
CS-1820 C0830
Fax Control PWB System Problem. Processing with the optional fax software was disabled due to a software or hardware problem.
Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software.
Engine PWB Backup Memory Read/Write Problem. Read and write data does not match.
Engine PWB EEPROM Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
Accounting Counts Problem. When the power is turned ON the total count and scan count are abnormal both on the main PWB and the engine PWB.
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.
Communication Problem between the main PWB and the engine PWB. When the power is turned ON, the machine does not detect the low level of SBSY and the high level of SDIR for 3 sec.
Communication Problem between the Main PWB and Operation PWB. There is no reply after 20 retrys at communication.
Fax Control PWB Communication Problem. Communication between the fax control PWB and the main PWB of the machine cannot be performed normally.
Image processing problem. JAM05 is detected twice.
Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
CS-1820 C0870
CS-1820 C0880
CS-1820 C0920
CS-1820 C2000
CS-1820 C3100
CS-1820 C3200
CS-1820 C4000
CS-1820 C4010
CS-1820 C6000
CS-1820 C6020
Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High-capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried several times.
Fax Control PWB Program Archive Problem. When power is turned On the compressed program in the flash ROM on the fax control PWB was not successfully decompressed.
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB.
Main Motor Problem. LOCK ALM signal remains high for 1 sec, 1 sec after the main drive motor has turned On.
Scanner Carriage Problem. Home position is not correct when power is turned On, or copying a document from the contact glass.
Exposure Lamp Problem. In indication check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 15 sec of START signal turning On.
Polygon Motor Steady-State Problem. The polygon motor rotation is not stable for 5 sec continuously after polygon motor stabilization.
Broken Fuser Heater Wire. The temperature does not reach 50C/122F within 13.5 sec. The temperature does not reach 100C/212F within 10 sec. Primary stabilization exceeds 10 sec. Secondary stabilization exceeds 24 sec.
Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects 230C/446F for 40ms or more.
CS-1820 C6050
CS-1820 C6400
CS-1820 C7800
CS-1820 C7810
CS-1820 C7980
CS-1820 C7990
CS-1820 CF010 ROM Checksum Error.
CS-1820 CF012 ROM Checksum Error.
CS-1820 CF1xx Controller System Error.
CS-1820 CF2xx Controller System Error.
CS-1820 CF3xx Controller System Error.
CS-1820 CF4xx Controller System Error.
CS-1820 CF5xx Controller System Error.
Abnormally Low Fuser Unit Thermistor Temperature. Thermistor detects 90C/194F or less for 1 sec continuously after initialization.
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec of power up, or 5 sec after initialization.
Broken External Thermistor Wire. The input voltage is 0.5 v or less.
Short Circuited External Thermistor. The input voltage is 4.5 v or more.
Waste Toner Reservoir Overflow Problem (when the total number of copies is less than 100K sheets). After E31 is displayed, 1000 sheets may be copied before shutdown. Or waste toner exceeds 5 grams.
Waste Toner Reservoir Overflow Problem (when the total number of copies is more than 100K sheets). After E31 is displayed, 1000 sheets may be copied before shutdown. Or waste toner exceeds 5 grams.
CS-1820 CF6xx Controller System Error.
CS-1820 CF7xx Controller System Error.
CS-1820 CF8xx Controller System Error.
CS-1820 CFxxx Controller System Error.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E00000 or U00000
Fax Communication Error: No response or line busy after the set number of redials.
E00100 or U00100
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
E00200 or U00200
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
E00300 or U00300
Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
E00431 or U00431
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E00431 or U00431
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00432 or U00432
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
E00432 or U00432
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
E00433 or U00433
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
E00433 or U00433
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
E00440 or U00440
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
E00441 or U00441
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
E00450 or U00450
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
E00460 or U00460
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00462 or U00462
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
E00600 or U00600
Fax Communication Error: The document processor cover is open.
E00601 or U00601
Fax Communication Error: Document jam or the document length exceeds the maximum.
E00602 or U00602
Fax Communication Error: Image scanning section problem
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820 Fax Communication Error: System error.
CS-1820
CS-1820
CS-1820
CS-1820
E00603 or U00603
Fax Communication Error: No document feed.
E00604 or U00604
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
E00610 or U00610
Fax Communication Error: Recording section cover open.
E00611 or U00611
Fax Communication Error: Recording paper jam.
E00613 or U00613
Fax Communication Error: Image writing section problem.
E00614 or U00614
Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615
Fax Communication Error: Empty of recording paper.
E00620 or U00620
Fax Communication Error: Copier fixing unit problem.
E00622 or U00622
Fax Communication Error: Copier drive motor problem.
E00655 or U00655
Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
E00670 or U00670
Fax Communication Error: Power was cut off during communication.
E00677 or U00677
Fax Communication Error: There was no file to transmit in the memory transmission mode.
E00690 or U00690
E00700 or U00700
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
E00800 or U00800
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
E00900 or U00900
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E00910 or U00910
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01013 or U01013
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
E01014 or U01014
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01019 or U01019
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
E01020 or U01020
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
E01021 or U01021
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
E01022 or U01022
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01026 or U01026
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01027 or U01027
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01028 or U01028
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
E01040 or U01040
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
E01044 or U01044
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01046 or U01046
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
E01047 or U01047
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
E01048 or U01048
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
E01052 or U01052
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
E01054 or U01054
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01055 or U01055
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
E01056 or U01056
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
E01057 or U01057
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
E01072 or U01072
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brak in loop current was detected during transmission.
E01073 or U01073
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
E01080 or U01080
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01091 or U01091
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E010x45 or U01045
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
E01100 or U01100
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
E01110 or U01110
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
E01111 or U01111
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01112 or U01112
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
E01113 or U01113
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
E01114 or U01114
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
E01115 or U01115
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
E01119 or U01119
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
E01120 or U01120
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
E01121 or U01121
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01122 or U01122
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
E01123 or U01123
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
E01124 or U01124
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
E01129 or U01129
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
E01140 or U01140
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
E01141 or U01141
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01142 or U01142
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
E01143 or U01143
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
E01148 or U01148
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
E01149 or U01149
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
E01150 or U01150
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01151 or U01151
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
E01152 or U01152
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
E01161 or U01161
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
E01162 or U01162
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
E01163 or U01163
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01164 or U01164
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
E01170 or U01170
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
E01191 or U01191
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
E01400 or U01400
Fax Communication Error: An invalid one-touch key was specified during communication.
E01500 or U01500
Fax Communication Error: A communication error occurred when calling in V.8 mode.
E01600 or U01600
Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E01720 or U01720
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E01721 or U01721
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in he period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E02000 or U02000
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
E02100 or U02100
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
E02303 or U02303
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected beofre a correct DNL signal was received.
E02304 or U02304
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
E02400 or U02400
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
E03000 or U03000
Fax Communication Error: No document was present in the destination unit when polling reception started.
E03100 or U03100
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E03200 or U03200
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
E03200 or U03200
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03300 or U03300
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
E03500 or U03500
Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination.
E03500 or U03500
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500
Fax Communication Error: The destination was being accessed.
E03600 or U03600
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
E03600 or U03600
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E03700 or U03700
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
E03700 or U03700
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
E04000 or U04000
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: The destination was being accessed.
E04100 or U04100
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
E04200 or U04200
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
E04300 or U04300
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
E04400 or U04400
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
E04401 or U04401
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
E04500 or U04500
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
E05000 or U05000
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
E09000 or U09000
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
E12000 or U12000
Fax Communication Error: In subaddress-based relay reception memory overflowed.
E12000 or U12000
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
E12100 or U12100
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
E14000 or U14000
Fax Communication Error: Memory overflowed during confidential reception.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820 message "Add paper to Casset. 1"
CS-1820 message
CS-1820 message "Add paper to MP Tray"
CS-1820 message "Close Document Processor Cover."
CS-1820 message "Close Document Processor."
CS-1820 message "Close Top Cover."
CS-1820 message "Enter address."
CS-1820 message "Enter destination."
E14000 or U14000
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
E19000 or U19000
Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100
Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
E19400 or U19400
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
"Add paper to Casset. 2" (with optional paper feeder)
CS-1820 message "Enter file name."
CS-1820 message "Enter host name."
CS-1820 message "Entry error. Enter correctly."CS-1820 message
CS-1820 message
CS-1820 message "Exceeded max count. Job is cancelled."
CS-1820 message "Illegal account. Job is cancelled."
CS-1820 message "Illegal user ID. Job is cancelled."
CS-1820 message "Insert cassette 1."
CS-1820 message "Insufficient memory. Unable to start job."
CS-1820 message "KPDL error. Job is cancelled. ####"
CS-1820 message "Load paper in Cassette 1. Size # Type #"
"Error occurred. Call service person. C####"
"Error occurred. Power switch off and on again. C####"
CS-1820 message "Load paper in Cassette 2. Size # Type #"
CS-1820 message "Load paper in MP Tray. Size # Type #"
CS-1820 message
CS-1820 message "Paper Jam at Cassette 1."
CS-1820 message "Paper Jam at Cassette 2."
CS-1820 message "Paper Jam at Document Processor."
CS-1820 message "Paper Jam at MP Tray."
CS-1820 message "Paper Jam in Printer."
CS-1820 message "Place original and press Start key."
"Memory Overflow. Part of the job end is printed."
CS-1820 message "Print overrun. This page isn't complete."
CS-1820 message
CS-1820 message "Replace Toner."
CS-1820 message
CS-1820 message "This key is not registered."
CS-1820 message "Toner low."
CS-1820 message "Waiting to scan."
CS-1820 message "Waste toner near full."
CS-1820 message "Wrong account ID."
"Remove original from Document Processor."
"Scan memory overflow. Job is cancelled."
CS-1820 message "Wrong password."
CS-1820 message "Wrong user ID."
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
Send Error 1101
Error: FTP Host Name. Enter the disable host name/IP address.
Send Error 1101
Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable SMB shared name.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable SMB user/password.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign the SMB user who is not allowed to access the folder.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB domain name is not entered.
Send Error 1102
Error: Username/Password or Shared Name/Folder Name. SMB host name error.
Send Error 1102
Error: Username/Password. Assign disable FTP user/password.
Send Error 1102
Error: Username/Password. FTP domain name is not entered.
Send Error 1102
Error: Username/Password. User ID for email authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send Error 1103
Error: Pathname or File Name. Assign disable FTP folder path.
Send Error 1103
Error: Pathname or File Name. Assign disable SMB folder path.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
Send Error 1103
Error: Pathname or File Name. Connection to the FTP folder which is not permitted for reference/writing.
Send Error 1103
Error: Pathname or File Name. Connection to the SMB folder which is not permitted for reference/writing.
Send Error 1104
Error: No Recipient Address. The destination email address is not specified.
Send Error 1105
Error: Not Supported Protocol. FTP protocol is set to OFF.
Send Error 1105
Error: Not Supported Protocol. SMB protocol is set to OFF.
Send Error 1105
Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send Error 1106
Error: No Sender Info. Sender email address is not entered.
Send Error 2101
Error: Can Not Connect. Assign the wrong FTP port number.
Send Error 2101
Error: Can Not Connect. Assign the wrong SMB port number.
Send Error 2101
Error: Can Not Connect. Enter the disable FTP host name/IP address.
Send Error 2101
Error: Can Not Connect. Enter the disable SMB host name/IP address.
Send Error 2101
Error: Can Not Connect. Network FTP is not connected.
Send Error 2101
Error: Can Not Connect. Network SMB is not connected.
Send Error 2101
Error: Can Not Connect. Network SMTP is not connected.
Send Error 2101
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send Error 2101
Error: Can Not Connect. The specified server is not SMTP server.
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
CS-1820
Send Error 2102
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send Error 2102
Error: Cannot Connect With Timeout. The FTP server is unable to communicate.
Send Error 2102
Error: Cannot Connect With Timeout. The SMTP server is unable to communicate.
Send Error 2103
Error: Response Wait With Timeout. The FTP server is unable to communicate.
Send Error 2103
Error: Response Wait With Timeout. The SMB server is unable to communicate.
Send Error 2103
Error: Response Wait With Timeout. The SMTPserver is unable to communicate.
Send Error 2201
Error: FTP Network Transfer. Error occurs on the network.
Send Error 2201
Error: SMB Network Transfer. Error occurs on the network.
Send Error 2201
Error: SMTP Network Transfer. Error occurs on the network.
Send Error 2202
Error: FTP Network Transfer With Timeout. Error occurs on the network.
Send Error 2202
Error: SMTP Network Transfer With Timeout. Error occurs on the network.
Send Error 2202
Error: TWAIN Network Transfer With Timeout. Response is not returned from the server, above the specified time.
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the FTP server, above specified time.
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the SMB server, above specified time.
Send Error 2203
Error: Response Wait With Timeout. Response is not returned from the SMTP server, above specified time.
Send Error 2204
Error: Email Size Limit. The size of the email attachment exceeds its limit.
CS-1820
CS-1820
CS-1820
Send Error 3101
Error: Server Response. SMTP server setting is not authenticated normally.
Send Error 3101
Error: Server Response. The FTP server is error status.
Send Error 3101
Error: Server Response. The SMTP server is error status.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
^/v to 20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize all data: Press System Menu/Counter, ^/v to Service, press & hold Start + # + Enter,
Enter > ^/v to Execute > Enter > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
^/v to 163
^/v to 163
Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,
Enter > ^/v to Execute > Enter > power Off/On.
Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,
Enter > ^/v to Execute > Enter > power Off/On.
^/v to 163
^/v to 163
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,
Enter > ^/v to Execute > Enter > power Off/On.
Press System Menu/ Counter, ^/v to Service, press & hold Start + # + Enter,
Enter > ^/v to Execute > Enter > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Turn power Off/On.
Turn power Off/On.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Service Checks1) Repl fax control PWB.
1) Upgrade firmware to compatible versions.
1) Reload firmware, 2) Repl engine PWB.
1) Repl engine PWB, 2) Repl main PWB.
1) Repl engine PWB, 2) Repl main PWB.
1) Repl engine PWB.
1) Repl fax control PWB.
1) Run simulation U020, 2) Repl backup RAM, 3) Repl engine PWB.
1) Reseat YC7 @ main PWB, 2) Reseat YC3 @ engine PWB, 3) Repl engine PWB, 4) Repl main PWB.
1) Reseat YC13 @ main PWB, 2) Reseat YC3 @ operation PWB, 3) Repl main PWB, 4) Repl operation PWB.
1) Reseat YC1 @ fax control PWB, 2) Reseat YC1 @ main PWB, 3) Repl fax control PWB, 3) Repl main PWB.
1) Repl fax control PWB.
1) Repl fax control PWB.
1) Reseat YC1 @ fax control PWB, 2) Reseat YC1 @ main PWB, 3) Repl fax control PWB, 3) Repl main PWB.
1) Reseat drive motor connectors, 2) Check drive components for excessive drag, 3) Repl main motor.
1) Reseat YC10/YC11 @ engine PWB, 2) Check scanner drive components for excessive drag, 3) Check/repl scanner HPS, 4) Repl scanner motor, 5) Repl scanner PWB, 6) Repl engine PCB.
1) Reseat YC7 @ scanner PWB, 2) Repl exposure lamp & inverter PCB, 3) Adjust shading plate detection position, 4) Repl scanner PWB.
1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC4 @ power supply PWB, 2) Check/repl thermistor (check contacting heat roller & clean), 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
1) Ohm out thermistor. If 0 ohms replace, 2) Repl power supply PWB.
1) Reseat YC4 @ power supply PWB, 2) Ohm out thermistor. If infinite replace, 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC7 @ engine PWB & YC2 @ PSU, 3) Check YC2-11 @ PSU for zero-crossing signal. If absent repl PSU, 4) If zero-crossing signal is present repl engine PWB.
1) Reseat operation panel connectors, 2) Repl operation panel PWB.
1) Reseat operation panel connectors, 2) Repl operation panel PWB.
1) Shake process unit side to side, then power Off/On, 2) Repl process unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl engine PWB.
1) Shake process unit side to side, then power Off/On, 2) Repl process unit, then power Off/On, 3) Repl waste toner sensor, 4) Repl engine PWB.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB.
Load paper.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
1) The paper has run out. Add paper to the paper source, 2) The cassette is not properly closed. Be sure the cassette it closed securely.
1) The paper has run out. Add paper to the paper source, 2) The cassette is not properly closed. Be sure the cassette it closed securely.
1) The paper has run out. Add paper to the paper source.
1) The left cover to the document processor is open. Close the cover securely.
1) The document processor is still open even though an original has been inserted. Close the document processor.
1) The top cover or the front cover is open. Close the covers securely.
1) Enter was pressed without entering a recipient. Input the recipient's address.
1) Start was pressed without entering a recipient. Input the recipient's address.
1) An invalid character was entered.
1) Enter was pressed without entering a file name. Input the file name.
1) Enter was pressed without entering a host name. Input the host name.
1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
1) Power Off/On. If error message remains, make a note of the number that is displayed together with the letter C. Then turn the power switch Off and contact your service representative.
1) When job accounting is enabled and the current job will exceed the account limit, press right Select to cancel the print job.
1) When job accounting is enabled and the selected account is invalid, press right Select to cancel the print job.
1) When job accounting is enabled and the wrong user ID or password is entered, press right Select to cancel the print job.
1) The paper feeder was selected, but cassette 1 is not installed properly. Push the upper cassette securely into the machine.
1) Memory shortage occurred during processing of other jobs.
1) Current print processing cannot continue. If you want to cancel printing press right Select. If Auto Error Clear is set to On, printing will be automatically resumed after a preset period of time.
1) There is no paper in the indicated cassette. Press right Select. 2) If you have loaded paper in the cassette select Print (continue) and press Enter. 3) To switch to another paper feeder location select Paper Select and press Enter. The available feed locations will be displayed. Select the desired paper feed location and press Enter.
1) There is no paper in the indicated cassette. Press right Select. 2) If you have loaded paper in the cassette select Print (continue) and press Enter. 3) To switch to another paper feeder location select Paper Select and press Enter. The available feed locations will be displayed. Select the desired paper feed location and press Enter.
1) There is no paper in the indicated cassette. Press right Select. 2) If you have loaded paper in the cassette select Print (continue) and press Enter. 3) To switch to another paper feeder location select Paper Select and press Enter. The available feed locations will be displayed. Select the desired paper feed location and press Enter.
1) The machines memory is full. Press left Select to cancel the copying procedure. 2) To end the job after a part of the job has been processed press right Select. 3) Insert fewer originals and try to copy again. 4) Add expansion memory.
1) A paper jam has occurred. Press left select to display the online help messages and remove the jammed paper.
1) A paper jam has occurred. Press left select to display the online help messages and remove the jammed paper.
1) A paper jam has occurred. Press left select to display the online help messages and remove the jammed paper.
1) A paper jam has occurred. Press left select to display the online help messages and remove the jammed paper.
1) A paper jam has occurred. Press left select to display the online help messages and remove the jammed paper.
1) The machine will attempt to make copies from any originals that remain uncopied. 2) Reposition the original on the platen or in the document feed tray and try to copy again.
1) The data transferred to the machine was too complex to print on a page. To continue printing press right Select. 2) To cancel printing press left Select.
1) This appears if there is a document in the document processor when the power is turned On. It also appears when the paper is jammed while being fed from the document processor because of the way it was placed. Remove all the document pages inside the document processor, and set them again correctly.
1) Toner has run out so further copying or printing is impossible. Replace the toner container using a new toner kit.
1) The total amount of data received by the machine exceeds the machine's internal memory. To verify the current amount of memory print out a Status Page. To cancel the copying procedure press right Select. If Auto Clear is set to On, printing will be automatically resumed after a preset period of time. 2) Lower the image quality.
1) An unregistered one-touch key was chosen. Select the correct one-touch key.
1) Toner is running low. Replace the toner container using a new toner kit as soon as possible.
1) The memory to execute the job is insufficient. The job will be automaticaly resumed after the memory capacity to execute is available. 2) To cancel the job press left Select.
1) Remove the process unit from the machine. Gently shake the process unit horizontally a few times. Reinstall it into the machine. 2) The machine will stop printing soon. Replace process unit.
1) When job accounting is enabled, the job accounting ID was already registered. Enter the correct account ID.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter the correct username/password.
Enter correct folder path.
Enter correct folder path.
1) When user login is enabled, an incorrect job accounting password was entered. Enter the correct password.
1) When user management setup (User Login) is enabled, an incorrect user ID was entered. Enter the correct user ID.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Enter the correct username/password. Check the access limit of destination folder.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Scan folder is not shared out to the network properly.
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Specify the destination address.
Enter the correct port number.
Enter the correct port number.
Enter the correct host name or IP address.
Enter the correct host name or IP address.
Select valid POP3 user other than [Other].
Enter the correct username/password. Check the access limit of destination folder.
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct host name or IP address.
Check if the server is operating properly.
Check if the server is operating properly.
Check is the server is operating properly.
Check is the server is operating properly.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check is the server is operating properly.
Check is the server is operating properly.
Check the settings for client/server authentication.
Model Error Code DescriptionC0030
CS-181, CS-221 C0070
C0100
C0110
CS-181, CS-221 C0130
CS-181, CS-221 C0140
C0150
C0160
C0170
C0180
C0210
C0240
CS-181 (2KJ), CS-221 (2KH)
Fax Control PWB System Problem. Processing with the fax software was disabled due to a software or hardware problem.
Fax Control PWB Incompatibility Problem. Fax software is not compatible with the main software.
CS-180 (2KLJ), CS-220 (2KK), CS-181,
CS-221
Main EEPROM Backup Memory Device Problem. Reading from or writing to EEPROM cannot be performed.
CS-180, CS-220, CS-181, CS-221
Main PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
Main PWB Backup Memory Device Problem. Reading from or writing to EEPROM cannot be performed.
Main PWB Backup Memory Data Problem. Reading data from EEPROM is abnormal.
CS-180, CS-220, CS-181, CS-221
Engine EEPROM Backup Memory Device Problem. Reading from or writing to EEPROM cannot be performed.
CS-180, CS-220, CS-181, CS-221
Engine PWB EEPROM Backup Memory Data Problem. Reading data from EEPROM is abnormal.
CS-180, CS-220, CS-181, CS-221
Copy Counts Problem. When the power is turned ON the total count and scan count are abnormal both on the main PWB and the engine PWB.
CS-180, CS-220, CS-181, CS-221
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.
CS-180, CS-220, CS-181, CS-221
Communication Problem between the main PWB and the engine PWB. When the power is turned ON, the machine does not detect the low level of SBSY and the high level of SDIR for 10 sec.
CS-180, CS-220, CS-181, CS-221
Printer PWB Printer Communication Problem. The printer PWB does not respond within 120 sec of power ON.
CS-181, CS-221 C0250
CS-181, CS-221 C0280
CS-180, CS-220 A0410
CS-181, CS-221 C0410
CS-180, CS-220 A0420
CS-181, CS-221 C0420
CS-181, CS-221 C0440
CS-180, CS-220 A0500
CS-181, CS-221 C0500
CS-180, CS-220 A0510
CS-181, CS-221 C0510
C0610
CS-180, CS-220 C0620
Scanner Network Board Communication Problem. The scanner network board does not respond.
Fax Control PWB Communication Problem. Communication between the fax control PWB and the main PWB of the machine cannot be performed normally.
DP-420 Communication Problem. Communication fails (5) times consecutively.
DP-420 Communication Problem. Communication fails (5) times consecutively.
PF-420 First Paper Feeder Communication Problem. Communication fails (5) times consecutively.
PF-420 First Paper Feeder Communication Problem. Communication fails (5) times consecutively.
DF-420 Internal Finisher Communication Problem. Communication fails (5) times consecutively.
PF-420 Second Paper Feeder Communication Problem. Communication fails (5) times consecutively.
PF-420 Second Paper Feeder Communication Problem. Communication fails (5) times consecutively.
PF-420 Third Paper Feeder Communication Problem. Communication fails (5) times consecutively.
PF-420 Third Paper Feeder Communication Problem. Communication fails (5) times consecutively.
CS-180, CS-220, CS-181, CS-221
Bitmap DIMM Problem. There is a problem with the data or address bus of the bitmap DRAM.
Memory Input Interface Problem. Reading-In of image does not complete within 10 sec of the start of image transmission
C0630
C0800
CS-181, CS-221 C0820
CS-181, CS-221 C0830
CS-181, CS-221 C0860
CS-181, CS-221 C0870
CS-181, CS-221 C0880
CS-181, CS-221 C0890
CS-181, CS-221 C0900
CS-181, CS-221 C0920
CS-180, CS-220, CS-181, CS-221
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-180, CS-220, CS-181, CS-221
Image processing problem. JAM05 is detected twice.
Fax Control PWB CG ROM Checksum Error. A checksum error occurred with the CG ROM data of the fax control PWB.
Fax Control PWB Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
Fax Control PWB Software Switch Checksum Error. A checksum error occurred with the software switch value of the fax control PWB.
Fax Control PWB to Main PWB High-Capacity Data Transfer Problem. High capacity data transfer between fax control PWB and main PWB was not normally performed even if data transfer was tried the specified times.
Fax Control PWB Program Archive Problem. When power is turned On the compressed program in the flash ROM on the fax control PWB was not successfully decompressed.
Fax Control PWB CG Font Archive Problem. Whe power is turned On, the compressed CG font in the flash ROM on the fax control PWB was not successfully decompressed.
Fax Software Incompatiblity Detection Problem. Version of the fax software is not compatible with that of the main software.
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PWB.
C2000
C2200
C3100
C3200
C3300
C4000
C4010
C4200
CS-180, CS-220, CS-181, CS-221
Drive Motor Problem. A stable state does not continue for 1 sec, 1 sec after the main drive motor has turned On.
CS-180, CS-220, CS-181, CS-221
Drum Motor Problem. A stable state does not continue for 1 sec, 1 sec after the drum motor has turned On.
CS-180, CS-220, CS-181, CS-221
Scanner Carriage Problem. Home position is not correct when power is turned On, or copying a document from the contact glass.
CS-180, CS-220, CS-181, CS-221
Exposure Lamp Problem. Non-lighting of the exposure lamp is detected at the beginning of copying.
CS-180, CS-220, CS-181, CS-221
Optical System AGC Problem. After AGC, correct input is not obtained at CCD. (Incorrect lamp intensity detected.)
CS-180, CS-220, CS-181, CS-221
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
CS-180, CS-220, CS-181, CS-221
Polygon Motor Steady-State Problem. The polygon motor rotation is not stable for 5 sec continuously after polygon motor stabilization.
CS-180, CS-220, CS-181, CS-221
BD Steady-State Problem. ASIC detects a Beam Detect error for 600ms after polygon motor stabilization.
C6000
C6020
C6050
C6400
C7800
C7810
CS-181, CS-221 C8170
CS-181, CS-221 C8180
CS-181, CS-221 C8190
CS-180, CS-220, CS-181, CS-221
Broken Fuser Heater Wire. The temperature does not reach 70C/158F within 15 sec before secondary stabilization. Temperature does not rise 1C/1.8F each 5 sec before secondary stabilization (except during printing).
CS-180, CS-220, CS-181, CS-221
Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects 230C/446F for 40ms or more.
CS-180, CS-220, CS-181, CS-221
Abnormally Low Fuser Unit Thermistor Temperature. Thermistor detects 90C/194F or less for 1 sec continuously after initialization.
CS-180, CS-220, CS-181, CS-221
Zero-Cross Signal Error. Interruption of the zero-cross signal does not occur more than 1 sec.
CS-180, CS-220, CS-181, CS-221
Broken External Thermistor Wire. The input voltage is 0.5 v or less.
CS-180, CS-220, CS-181, CS-221
Short Circuited External Thermistor Wire. The input voltage is 4.5 v or more.
DF-420 Internal Finisher Front Side Registration Motor Problem. If front side registration HPS is On at initialization, sensor does not turn Off within 106 pulses. If HPS is Off at initialization, sensor does not turn On within 3000ms.
DF-420 Internal Finisher Rear Side Registration Motor Problem. If rear side registration HPS is On at initialization, sensor does not turn Off within 106 pulses. If HPS is Off at initialization, sensor does not turn On within 3000ms.
DF-420 Internal Finisher Trailing Edge Registration Motor Problem. If trailing edge registration HPS is On at initialization, sensor does not turn Off within 106 pulses. If HPS is Off at initialization, sensor does not turn On within 3000ms.
CS-181, CS-221 C8210
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
DF-420 Internal Finisher Stapler Problem. During initialization, stapler HPS does not change state from Off to On within 600ms of start of motor CW rotation (reverse). Stapler HPS does not change state from Off to On within 200ms of start of motor CCW rotation (forward).
E00000 or U00000
Fax Communication Error: No response or line busy after the set number of redials.
E00100 or U00100
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
E00200 or U00200
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
E00300 or U00300
Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
E00431 or U00431
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00431 or U00431
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E00432 or U00432
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
E00432 or U00432
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
E00433 or U00433
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
E00433 or U00433
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
E00440 or U00440
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
E00441 or U00441
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
E00450 or U00450
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
E00462 or U00462
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
E00600 or U00600
Fax Communication Error: The document processor cover is open.
E00601 or U00601
Fax Communication Error: Document jam or the document length exceeds the maximum.
E00602 or U00602
Fax Communication Error: Image scanning section problem
E00603 or U00603
Fax Communication Error: No document feed.
E00604 or U00604
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221 Fax Communication Error: System error.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E00610 or U00610
Fax Communication Error: Recording section cover open.
E00611 or U00611
Fax Communication Error: Recording paper jam.
E00613 or U00613
Fax Communication Error: Image writing section problem.
E00614 or U00614
Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615
Fax Communication Error: Empty of recording paper.
E00620 or U00620
Fax Communication Error: Copier fixing unit problem.
E00622 or U00622
Fax Communication Error: Copier drive motor problem.
E00655 or U00655
Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
E00670 or U00670
Fax Communication Error: Power was cut off during communication.
E00677 or U00677
Fax Communication Error: There was no file to transmit in the memory transmission mode.
E00690 or U00690
E00700 or U00700
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
E00800 or U00800
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
E00900 or U00900
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
E00910 or U00910
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01013 or U01013
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01014 or U01014
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
E01019 or U01019
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
E01020 or U01020
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01021 or U01021
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
E01022 or U01022
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PSS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PSS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
E01026 or U01026
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01027 or U01027
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01028 or U01028
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
E01040 or U01040
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
E01044 or U01044
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
E01045 or U01045
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01046 or U01046
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
E01047 or U01047
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
E01048 or U01048
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
E01052 or U01052
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
E01054 or U01054
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01055 or U01055
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
E01056 or U01056
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
E01057 or U01057
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
E01072 or U01072
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brak in loop current was detected during transmission.
E01073 or U01073
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
E01080 or U01080
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01091 or U01091
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E01100 or U01100
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
E01110 or U01110
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
E01111 or U01111
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
E01112 or U01112
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01113 or U01113
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
E01114 or U01114
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
E01115 or U01115
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
E01119 or U01119
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
E01120 or U01120
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
E01121 or U01121
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
E01122 or U01122
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01123 or U01123
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
E01124 or U01124
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
E01129 or U01129
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
E01140 or U01140
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
E01141 or U01141
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
E01142 or U01142
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01143 or U01143
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
E01148 or U01148
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
E01149 or U01149
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIP signal.
E01150 or U01150
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
E01151 or U01151
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01152 or U01152
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RNR signal (ECM).
E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
E01161 or U01161
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
E01162 or U01162
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
E01163 or U01163
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
E01164 or U01164
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01170 or U01170
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
E01191 or U01191
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
E01400 or U01400
Fax Communication Error: An invalid one-touch key was specified during communication.
E01500 or U01500
Fax Communication Error: A communication error occurred when calling in V.8 mode.
E01600 or U01600
Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01720 or U01720
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E01721 or U01721
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E01821 or U01821
Fax Communication Error: Operation was interrupted due to absence of a common communication speed between units (including when an impossible combination of communication speed and symbol speed occurs) after MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut.
E02000 or U02000
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was issued.
E02100 or U02100
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
E02303 or U02303
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
E02304 or U02304
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E02400 or U02400
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
E03000 or U03000
Fax Communication Error: No document was present in the destination unit when polling reception started.
E03100 or U03100
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
E03200 or U03200
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
E03200 or U03200
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03300 or U03300
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
E03500 or U03500
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
E03500 or U03500
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500
Fax Communication Error: The destination was being accessed.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E03600 or U03600
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
E03600 or U03600
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
E03700 or U03700
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
E03700 or U03700
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
E04000 or U04000
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
E04000 or U04000
Fax Communication Error: The destination was being accessed.
E04100 or U04100
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
E04200 or U04200
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
E04300 or U04300
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
E04400 or U04400
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
E04401 or U04401
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
E04500 or U04500
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
E05000 or U05000
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
E09000 or U09000
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220 The copier is in Low Power Mode.
CS-180, CS-220 The copier is in Sleep Mode.
E12000 or U12000
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
E12000 or U12000
Fax Communication Error: In subaddress-based relay reception memory overflowed.
E12100 or U12100
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
E14000 or U14000
Fax Communication Error: Memory overflowed during confidential reception.
E14000 or U14000
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
E19000 or U19000
Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100
Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
E19400 or U19400
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
"- - -" appears in the copy quantity
display
"-" appears in the copy quantity
display
CS-180, CS-220 Job Accounting is enabled.
CS-181, CS-221
There is no paper in the cassette.
CS-180, CS-220 "Add Toner."
CS-181, CS-221 An error has occurred.
CS-180, CS-220 An error has occurred. See above:
CS-180, CS-220
CS-180, CS-220
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221 The slit glass is dirty.
"= = =" appears in copy quantity
display
"Add paper in cassette ## size
(###)."
Print data does not match the size or type of paper in the cassette. Replace the paper.
CS-180, CS-220, CS-181, CS-221
"Add paper in cassette #."
Copies cannot be produced because there is no toner.
"Call for service. C####"
"Call service. C####"
"Cannot copy this orig. size."
An original that cannot be copied has been set. 1) The original was set in a vertical direction during the Book Border Erase copying operation. 2) An irregular size original was set during Border Erase or Combine mode operation. 3) An original size other than Letter, Ledger, A3, A4R, A5R, B4, or B5R was set to make a split copy or duplex copy from a double page spread original.
"Cannot duplex this paper size."
Duplex copies cannot be made when A6R, B6R, Postcard, Irregular Size, or the paper size has not been specified.
"Cannot staple this size."
Stapling of small paper, such as Statement, A5R, an B5R is not possible.
"Check paper size."
There is no paper loaded of a size that can be used in the current selected mode.
"Checksum Error"
The machine has detected an error at startup.
"Clean the slit glass for original
fed from DP."
CS-181, CS-221 "Close ## cover." The indicated cover is open."
CS-180, CS-220
CS-180, CS-220 The Document Processor is open.
CS-180, CS-220 The front cover of the copier is open.
CS-180, CS-220 The left cover of the cassette is open.
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220 Check the key counter.
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220
CS-181, CS-221
CS-180, CS-220
CS-180, CS-220 Memory is full.
"Close document processor
cover."
The left cover of the document processor is open.
"Close document processor."
"Close front cover."
"Close left cover #."
"Exceed copy limit. Unable to
copy."
The number of copies made with your management code has reached the limit that was set in the department management mode, and copying is no longer possible with that code.
"Format error Memory card."
An unformatted memory card has been inserted, or when the machine has tried to read data from the memory card the memory card is not recognized.
"Insert Key Counter"
"Insert same memory card."
When the machine has tried to read data from the memory card, the memory card is not recognized.
"Interface occupied."
The selected interface is currently being used.
"Main Power Off/On A####"
A customer recoverable error code has occurred.
"Memory card error. Insert
again."
The memory card is accidentally removed during printer setting.
"Memory is full. Cannot
continue."
Copies cannot be produced because memory is full during the interrupt copy operation. Interrupt copying cannot be carried out.
"Memory is full. Press OK."
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220 Check the MP Tray paper.
CS-180, CS-220
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220 "Paper jam." A paper misfed has occurred.CS-181, CS-221
"Memory is full." when copying.
Current copying cannot be processed because the memory for copying is full or the number of originals has reached the limit of 999 pages. Depending on the copy setting conditions, only one set of copies may be output, and this error message may be displayed even if a multiple number of copies is specified. In this case, copying cannot be continued.
"Memory is full." when printing.
Current printing cannot be processed because the memory for printing is full.
"MemoryCard err. Press GO."
An error has occurred in writing to or reading from the memory card.
"Misfeed in DP. Remove
original(s)."
Originals have jammed in the optional document processor.
"MP tray empty. Add paper."
"No matching paper available."
No letter/A4 paper was available in either cassette or the MP tray when a report was attempted to be output.
"Out of Staples. Please Add
Staples."
There are no staples left in the optional finisher.
"Paper capacity exceeded.
Remove paper from Job sep." when copying.
100 copies have accumulated on the optional job separator.
"Paper misfeed in the Finisher, lower Process
Tray and remove paper.
Paper has jammed in the optional finisher.
CS-181, CS-221 "Paper misfeed." A paper misfed has occurred.
CS-180, CS-220 An original has misfed.
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-181, CS-221
CS-180, CS-220
The waste toner box is full.
"Place orig on doc processor."
"Print overrun. Press GO."
Printing has not been performed properly because of insufficient memory.
"RAM disk error. Press GO."
An error has occurred in writing to or reading from the RAM disk.
"Ready to copy. Toner low."
Toner remaining in the machine is low. It is possible to copy only one by one.
"Remove paper from Finisher. Press START
key." when copying.
250 copies have accumulated on the finisher tray.
"Remove paper from the
Finisher. Press GO." when
printing.
250 prints have accumulated on the finisher tray.
"Remove paper from the Top
tray. Press GO." when printing.
250 prints have accumulated on the output tray. Or 150 copies have accumulated on the output tray with job separator installed. Or 100 copies have accumulated on the output tray when the optional finisher is installed.
"Remove paper from the Top tray. Press
START key." when copying.
250 copies have accumulated on the output tray. Or 150 copies have accumulated on the output tray with job separator installed. Or 100 copies have accumulated on the output tray when the optional finisher is installed.
"Remove paper on top tray;
Start."
250 copies have accumulated on the output tray.
CS-180, CS-220, CS-181, CS-221
"Replace waste toner box."
CS-181, CS-221
CS-180, CS-220
CS-181, CS-221
CS-180, CS-220
CS-181, CS-221
CS-181, CS-221 It is time for Periodic Maintenance.
CS-181, CS-221 No toner remains.
CS-180, CS-220 There is very little toner remaining.
CS-180, CS-220
CS-180, CS-220 It is time for Periodic Maintenance.
"Reposition original or change
cassette."
The orientations of the original and the selected paper are different.
"Reseat originals on DP."
Originals were set in the optional Document Processor when copying 2-sides, when copying from the platen in 2-sided copy, 2 in 1, 4 in 1, or when collating copies.
"Reset all originals in DP."
If the optional Document Processor is being used, there are originals left on the originals table.
"Return all originals to DP."
If the optional Document Processor is being used, there are originals left on the originals table.
CS-180, CS-220, CS-181, CS-221
"Set paper cassette"
Check the paper cassette that corresponds to the lighting indicator.
CS-180, CS-220, CS-181, CS-221
"Set toner container."
The toner container has not been set properly.
CS-180, CS-220, CS-181, CS-221
"Shake the toner container."
Tap and shake the new toner container without spilling toner, and install it again.
"System Error. Main switch
Off/On." when printing.
A malfunction has occurred due to noise or a communication error occurred during printer processing.
"Time for maintenance."
"Unable to copy. Please add
toner."
Add Toner indicator blinks
On and Off
Periodic Maintenance
indicator blinks On and Off
This is a notification that the time for periodic maintenance is approaching.
Periodic Maintenance
indicator lights solid
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
20
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163
10871087 163
10871087 163
10871087 163
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
10871087 906
Use +/- Zoom keys to 163 > Start > "CLE" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > "CLE" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > "CLE" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > "CLE" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
10871087 906 Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Service Checks1) Repl fax control PWB.
1) Upgrade firmware to compatible versions.
1) Repl EEPROM, 2) Repl main PWB.
1) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Run simulation U020, 2) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Run simulation U020, 2) Repl EEPROM, 3) Repl main PWB.
1) Reload firmware, 2) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Run simulation U020, 2) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Repl main/engine PWB (180-220), or main or engine PWB (181-221).
1) Contact Kyocera Service Administrative Division, 2) Install the correct EEPROM, 3) Repl main/engine PWB (180-220), or main or engine PWB (181-221).
1) Reseat cables & connectors, 2) Repl main/engine PWB (180-220), or main or engine PWB (181-221).
1) Reseat interface PWB to printer PWB, 2) Repl printer PWB. 3) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Repl main/engine PWB.
1) Reseat scanner network board, 2) Repl scanner network PWB, 3) Repl main PWB.
1) Reseat fax control PCB (YC1 @ fax PWB & YC10 @ main PWB), 2) Repl fax control PWB, 3) Repl main PWB.
1) Reseat DP connectors, 2) Repl DP driver PWB, 3) Repl main/engine PWB.
1) Reseat DP connectors, 2) Repl DP driver PWB, 3) Repl engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main/engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl engine PWB.
1) Reseat DF connectors (YC1 @ finisher main PWB and YC4 @ engine PWB), 2) Repl finisher main PWB, 3) Repl engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main/engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main/engine PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl engine PWB.
1) Reseat DIMM on main/engine or main PWB, 2) Repl DIMM on main/engine or main PWB, 3) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Repl fax control PWB.
1) Repl fax control PWB.
1) Repl fax control PWB.
1) Repl fax control PWB.
1) Upgrade firmware to compatible versions.
1) Repl fax control PWB.
1) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Repl main/engine PWB (180-220) and main PWB (181-221).
1) Upgrade or reload fax firmware, 2) Repl fax control PWB.
1) Reseat fax control PCB (YC1 @ fax PWB & YC10 @ main PWB), 2) Repl fax control PWB, 3) Repl main PWB.
1) Reseat drive motor connectors and YC6 @ main/engine PWB (180-220) or YC6 @ engine PWB (181-221), 2) Check drive components for excessive drag, 3) Repl drive motor, 4) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Reseat drum motor connectors and YC6 @ main/engine PWB (180-220) or YC6 @ engine PWB (181-221), 2) Check drive components for excessive drag, 3) Repl drum motor, 4) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Reseat scanner motor connectors, HPS connector, and YC5 @ main/engine PWB (180-220) or engine PWB (181-221), 2) Check scanner drive components for excessive drag, 3) Check/repl scanner HPS, 4) Repl scanner motor, 5) Repl main/engine PCB (180-220) or engine PWB (181-221).
1) Reseat lamp circuit connectors and YC16 @ main/engine PWB (180-220) or engine PWB (181-221), 2) Repl exposure lamp & inverter PCB, 3) Adjust shading plate detection position, 4) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Reseat lamp circuit connectors, CCD connectors, and YC27 @ main/engine PWB (180-220) or YC5 @ main PWB (181-221), 1) Repl exposure lamp & inverter PWB, 2) Adjust shading plate detection position, 3) Repl CCD, 4) Repl main/engine PWB (180-220) or main PWB (181-221).
1) Reseat laser unit connectors and YC3 @ main/engine PWB (180-220) or YC3 @ engine PWB, 2) Repl laser unit, 3) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Reseat laser unit connectors and YC3 @ main/engine PWB (180-220) or YC3 @ engine PWB, 2) Repl laser unit, 3) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Reseat laser unit connectors and YC3 @ main/engine PWB (180-220) or YC3 @ engine PWB, 2) Repl laser unit, 3) Repl main/engine PWB (180-220) or engine PWB (181-221).
1) Check that thermistor is contacting heat roller & clean, 2) Check/repl thermal switch, 3) Check/repl fixing heaters.
1) Check thermistor resistance, if 0 ohms replace, 2) Repl power supply PWB.
1) Check thermistor resistance, if infinite ohms replace, 2) Check that thermistor is contacting heat roller & clean, 3) Check/repl thermal switch, 4) Check/repl fixing heaters.
1) Check wall outlet ground to neutral voltage. 2) Check YC2-2 @ PSU for zero-crossing signal. If absent repl PSU, 3) If zero-crossing signal is present repl Main/Engine PWB (180-220) or engine PWB (181-221).
1) Reseat humidity sensor connector, 2) Repl the cassette PWB.
1) Reseat humidity sensor connector, 2) Repl the cassette PWB.
1) Reseat connector or replace front registration motor, 2) Reseat connector or replace front registration HPS, 3) Repl finisher control PWB.
1) Reseat connector or replace rear registration motor, 2) Reseat connector or replace rear registration HPS, 3) Repl finisher control PWB.
1) Reseat connector or replace trailing edge registration motor, 2) Reseat connector or replace trailing edge registration HPS, 3) Repl finisher control PWB.
Load paper.
1) Reseat stapler connector, 2) Remove jammed staples & confirm proper staple installation, 3) Repl stapler, 4) Repl finisher control PWB.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Press [Energy Saver] to exit sleep mode.
Press any key to exit Low Power Mode, or in the case where the optional Document Processor is installed, set an original in the Document Processor.
Replace the toner container with a new one.
Specify a paper size that can be used.
Check the paper.
Use the numeric keys to enter the assigned Section Code to perform copying operations. Press [Logout] after copying is finished to display "= = =" again.
To change the paper source, press [Paper Select] key to select desired paper source and press [Enter] key. If you press [Printer] key, the following messages are displayed: GO: Prints onto the currently selected paper, CANCEL: Stops printing. Press ^/v key to select desired paper tray and press [Enter] key.
Load paper into the cassette as displayed in place of #.
Open the front cover once and close it. If the message is displayed again note the 5 digit error number. Contact service.
Check the original. 1) Set the original horizontally. 2) Back the irregular original with a standard sized white piece of paper. 3) Back the irregular original with a standard sized white piece of paper.
Select a larger paper size or turn Off stapling.
Main power Off/On to reset. If re-occurs call service.
Clean the slit glass because black lines may be copied when the optional document processor is used.
Close all the covers securely.
Close the left cover, close the front cover.
Close the Document Processor.
Close the front cover.
Make sure the key counter is set properly.
Wait for a while and retry.
Power Off. Insert memory card. Power On.
Close the left cover as displayed in place of #.
Contact your system administrator. Use the department management mode to clear the copy count.
Format the memory card. If the formatting fails, the card may be corrupt/defective.
Power Off. Re-insert memory card. Power On.
Turn power switch Off/On. Usage will be possible again once the regular display returns. If the code re-occurs, note the error code, and contact service.
Press [Stop/Clear], then [Interrupt] again after the data read in has been deleted, to exit the Interrupt Copying. After the copying operation for the interrupted copy has been complete, repeat the procedure again.
Press [OK] to start outputting the copies read in. Press [Reset} or [Stop/Clear] to delete the data read in. Reduce the number of originals and repeat the copying procedure.
Add staples.
Remove the paper. Copying will resume.
Remove the jammed paper.Remove the paper.
Select [Copy Scanned Image] to output the pages that have been scanned, or press [Cancel] to delete scanned data. Press the [Enter] key and perform copying operation again. If this error occurs frequently, additional memory is recommended.
Press the [Printer] key to display these messages: GO: Continues printing. CANCEL: Cancels printing. RESET: Resets the printer board. Only the printer functions will be reset. If using RAM Disk function reduce the size of the RAM disk. If this error occurs frequently, additional memory is recommended.
Press [Printer], select [GO], and press [Enter]. The error will be cleared.
Leave the main power switch On, and follow the appropriate procedure to remove the jammed originals.
Set paper in the MP Tray in the event there is no paper present there. When the MP Tray paper fails to be fed, reset the paper.
Press [Paper Selection] and select the supply cassette, then press [Start]. Paper will be supplied from the cassette selected.
Remove the paper. Copying will resume.
Remove the paper. Copying will resume.
Replace it with a new waste toner box.
The location of the jam is indicated on the message display, and the machine stops.Leave the main power switch On and folow the appropriate procedure to remove the jammed paper.
The copier will try to make copies of the originals it could not copy before. Return all originals to the originals table and try copying them again.
Press the [Printer] key to display these messages: GO: Continues printing. CANCEL: Cancels printing. RESET: Resets the printer board. Only the printer functions will be reset. If this error occurs frequently, additional memory is recommended.
Press [Printer], select [GO], and press [Enter]. The error will be cleared.
Replace the toner container as soon as possible.
Remove the paper. Press [Printer], then ^/v key to select [GO], then [Enter] to resume printing. Select [CANCEL], then [Enter] to cancel printing.
Remove the paper. Press [Printer], then ^/v key to select [GO], then [Enter] to resume printing. Select [CANCEL], then [Enter] to cancel printing.
Remove the paper, press [Start] and resume copying.
Set the toner container properly.
Contact your service representative.
Replace the toner container.
Contact your service representative.
Change the orientation of the original. If you press [Start] key without changing the orientation, copying will be performed at 100% (1:1) magnification ratio.
Remove the originals from the Document Processor. Replace the originals on the original table after exiting the front and back copying, 2-sided copy, 2 in 1, 4 in 1, or Collate Mode and resume copying.
Remove the originals, return them to the original table and try copying them again.
Remove the originals, return them to the original table and try copying them again.
Set the cassette. First pull it out and push it all the way back in.
Tap and shake the new toner container without spilling toner, and install it again.
Clear the print queue. Main power Off, wait more than 5 seconds, then main power On. Attempt printing again.
Copying can be continued for a short while before running out of toner. Prepare the replacement toner container.
Model Error Code DescriptionC0030
C0070
C0100
C0110
CS2550 C0120 Drum EEPROM Read/Write Problem.
C0130
C0140
C0150
C0160
C0170
C0180
C0210
CS1650 (2DA), CS2050 (2DB), CS2550 (2FT)
Fax Control PCB System Problem. Processing with the fax software was disabled due to a software or hardware problem.
CS1650, CS2050, CS2550
Fax Control PCB Incompatibility Problem. Fax software is not compatible with the main software.
CS1635 (2HA), CS1650, CS2050,
CS2550
Main PWB Backup Memory Read/Write Problem. Read and write data does not match.
CS1635, CS1650, CS2050, CS2550
Main PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS1650, CS2050, CS2550
Main PWB Backup Memory Read/Write Problem. Read and write data does not match.
CS1650, CS2050, CS2550
Main PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS1635, CS1650, CS2050, CS2550
Engine PWB Backup Memory Read/Write Problem. Read and write data does not match.
CS1635, CS1650, CS2050, CS2550
Engine PWB EEPROM Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS1635, CS1650, CS2050, CS2550
Accounting Counts Problem. When the power is turned ON the total count and scan count are abnormal both on the main PWB and the engine PWB.
CS1635, CS1650, CS2050, CS2550
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs.
CS1635, CS1650, CS2050, CS2550
Communication Problem between the main PWB and the engine PWB. When the power is turned ON, the machine does not detect the low level of SBSY and the high level of SDIR for 10 sec.
C0240
C0250
C0280
C0410
C0420
C0440
C0500
C0510
C0610
CS1635 C0620
C0630
CS1635 C0800
C0800
CS1635, CS1650, CS2050, CS2550
Printer PWB Printer Communication Problem. The printer PWB does not respond within 120 sec of power ON.
CS1650, CS2050, CS2550
Scanner Network Board Communication Problem. The scanner network board does not respond.
CS1650, CS2050, CS2550
Fax Control PCB Communication Problem. Communication between the fax control PCB and the main PCB of the machine cannot be performed normally.
CS1635, CS1650, CS2050, CS2550
DP-410 Communication Problem. Communication fails (5) times consecutively.
CS1635, CS1650, CS2050, CS2550
PF-410 First Paper Feeder Communication Problem. Communication fails (5) times consecutively.
CS1650, CS2050, CS2550
DF-410 Internal Finisher Communication Problem. Communication fails (5) times consecutively.
CS1635, CS1650, CS2050, CS2550
PF-410 Second Paper Feeder Communication Problem. Communication fails (5) times consecutively.
CS1635, CS1650, CS2050, CS2550
PF-410 Third Paper Feeder Communication Problem. Communication fails (5) times consecutively.
CS1635, CS1650, CS2050, CS2550
Bitmap DIMM Problem. There is a problem with the data or address bus of the bitmap DRAM.
Memory Input Interface Problem. Reading-In of image does not complete within 10 sec of the start of image transmission
CS1635, CS1650, CS2050, CS2550
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
Image processing problem. JAM05 is detected twice.
CS1650, CS2050, CS2550
Image processing problem. JAM05 is detected twice.
C0820
C0830
C0860
C0870
C0880
C0890
C0900
C0920
CS2550 C0960
C2000
CS1650, CS2050, CS2550
Fax Control PCB CG ROM Checksum Error. A checksum error occurred with the CG ROM data of the fax control PCB.
CS1650, CS2050, CS2550
Flash ROM Program Area Checksum Error. A checksum error occurred with the program of the fax control PCB.
CS1650, CS2050, CS2550
Fax Control PCB Software Switch Checksum Error. A checksum error occurred with the software switch value of the fax control PCB.
CS1650, CS2050, CS2550
Fax Control PCB to Main PCB High-Capacity Data Transfer Problem. High capacity data transfer between fax control PCB and main PCB was not normally performed even if data transfer was tried several times.
CS1650, CS2050, CS2550
Fax Control PWB Program Archive Problem. When power is turned On the compressed program in the flash ROM on the fax control PWB was not successfully decompressed.
CS1650, CS2050, CS2550
Fax Control PCB CG Font Archive Problem. Whe power is turned On, the compressed CG font in the flash ROM on the fax control PCB was not successfully decompressed.
CS1650, CS2050, CS2550
Fax Software Incompatiblity Detection Problem. Version of the fax software is not compatible with that of the main software.
CS1650, CS2050, CS2550
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax control PCB.
Developer EEPROM Read/Write problem. Read and write data does not match.
CS1635, CS1650, CS2050, CS2550
Drive Motor Problem. LOCK ALM signal remains high for 1 sec, 1 sec after the main drive motor has turned On.
C3100
C3200
C3300
C4000
C4010
C4200
CS1635, CS2550 C6000
CS1650, CS2050 C6000
C6020
CS1635, CS1650, CS2050, CS2550
Scanner Carriage Problem. Home position is not correct when power is turned On, or copying a document from the contact glass.
CS1635, CS1650, CS2050, CS2550
Exposure Lamp Problem. Non-lighting of the exposure lamp is detected at the beginning of copying.
CS1635, CS1650, CS2050, CS2550
Optical System AGC Problem. After AGC, correct input is not obtained at CCD. (Incorrect lamp intensity detected.)
CS1635, CS1650, CS2050, CS2550
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec (CS1635, CS2550), or 15 sec (CS1650, CS2050) of activation.
CS1635, CS1650, CS2050, CS2550
Polygon Motor Steady-State Problem. The polygon motor rotation is not stable for 5 sec continuously after polygon motor stabilization.
CS1635, CS1650, CS2050, CS2550
BD Steady-State Problem. MIP detects a Beam Detect error for 600ms after polygon motor stabilization.
Broken Fuser Heater Wire. The temperature does not exceed 100C/212F within 30 sec before secondary stabilization. Temperature does not rise 1C/1.8F each 5 sec before secondary stabilization.
Broken Fuser Heater Wire. The time to reach 50C/122F exceeds 13.5 sec, the time from 50C/122F to 100C/212F exceeds 10 sec, or the time before secondary stabilization exceeds 24 sec.
CS1635, CS1650, CS2050, CS2550
Abnormally High Fuser Unit Thermistor Temperature. Thermistor detects 230C/446F (CS1635, CS1650, CS2050) or 240C/464F (CS2550) for 40ms or more.
C6050
C6400
CS2550 C6420
CS2550 C7400
CS2550 C7410
CS1635 C7750
CS1635 C7760
C7800
C7810
C8170
C8180
CS1635, CS1650, CS2050, CS2550
Abnormally Low Fuser Unit Thermistor Temperature. Thermistor detects 90C/194F or less for 1 sec continuously after initialization.
CS1635, CS1650, CS2050, CS2550
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec of power up, or 5 sec after initialization.
Fixing Fuse Cut Problem. When you try to cut the fixing fuse, the fixing is not cut within 3 sec.
Developing Unit Connector Insertion Problem. Absence of the developing unit is detected.
Drum Unit Connector Insertion Problem. Absence of the drum unit is detected.
Drum Type Mismatch Problem A. The drum type does not match with the software.
Drum Type Mismatch Problem B. The drum type is undefined.
CS1635, CS1650, CS2050, CS2550
Broken External Thermistor Wire. The input voltage is 0.5 v or less.
CS1635, CS1650, CS2050, CS2550
Short Circuited External Thermistor Wire. The input voltage is 4.5 v or more.
CS1650, CS2050, CS2550
DF-410 Internal Finisher Front Side Registration Motor Problem. If front side registration HPS is On at initialization, sensor does not turn Off within 570ms. If HPS is Off at initialization, sensor does not turn On within 3180ms.
CS1650, CS2050, CS2550
DF-410 Internal Finisher Rear Side Registration Motor Problem. If rear side registration HPS is On at initialization, sensor does not turn Off within 570ms. If HPS is Off at initialization, sensor does not turn On within 2880ms.
C8190
C8210
CS1635 F000
CS1635 F010 Main PWB Checksum Error.CS1635 F020 Memory Checksum Error.
CS1635 F030 Main PWB System Error.CS1635 F040 Engine PWB Communication Error.
CS1635 F050 Engine ROM Checksum Error.E00000 or U00000
E00100 or U00100
E00200 or U00200
E00300 or U00300
E00420 or U00420
E00421 or U00421
CS1650, CS2050, CS2550
DF-410 Internal Finisher Trailing Edge Registration Motor Problem. If trailing edge registration HPS is On at initialization, sensor does not turn Off within 570ms. If HPS is Off at initialization, sensor does not turn On within 4550ms.
CS1650, CS2050, CS2550
DF-410 Internal Finisher Front Stapler Problem. During initialization, front stapler HPS does not change state from Off to On within 600ms of start of motor CW rotation (reverse). Front stapler HPS does not change state from Off to On within 200ms of start of motor CCW rotation (forward).
Operation Panel PWB Communication Error.
CS1650, CS2050, CS2550
Fax Communication Error: No response or line busy after the set number of redials.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
CS1650, CS2050, CS2550
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
CS1650, CS2050, CS2550
Fax Communication Error: Recording paper on the destination unit has run out during reception.
CS1650, CS2050, CS2550
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430
E00430 or U00430
E00431 or U00431
E00431 or U00431
E00432 or U00432
E00432 or U00432
E00433 or U00433
E00433 or U00433
E00434 or U00434
CS1650, CS2050, CS2550
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
CS1650, CS2050, CS2550
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435
E00435 or U00435
E00440 or U00440
E00440 or U00440
E00440 or U00440
E00441 or U00441
E00450 or U00450
E00460 or U00460
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
CS1650, CS2050, CS2550
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460
E00462 or U00462
E00500 or U00500
E00600 or U00600
E00601 or U00601
E00602 or U00602
E00603 or U00603
E00604 or U00604
E00610 or U00610
E00611 or U00611
E00613 or U00613
E00614 or U00614
E00615 or U00615
E00620 or U00620
E00622 or U00622
E00655 or U00655
CS1650, CS2050, CS2550
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
CS1650, CS2050, CS2550
Fax Communication Error: The document processor cover is open.
CS1650, CS2050, CS2550
Fax Communication Error: Document jam or the document length exceeds the maximum.
CS1650, CS2050, CS2550
Fax Communication Error: Image scanning section problem
CS1650, CS2050, CS2550
Fax Communication Error: No document feed.
CS1650, CS2050, CS2550
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS1650, CS2050, CS2550
Fax Communication Error: Recording section cover open.
CS1650, CS2050, CS2550
Fax Communication Error: Recording paper jam.
CS1650, CS2050, CS2550
Fax Communication Error: Image writing section problem.
CS1650, CS2050, CS2550
Fax Communication Error: Nearly empty of recording paper.
CS1650, CS2050, CS2550
Fax Communication Error: Empty of recording paper.
CS1650, CS2050, CS2550
Fax Communication Error: Copier fixing unit problem.
CS1650, CS2050, CS2550
Fax Communication Error: Copier drive motor problem.
CS1650, CS2050, CS2550
Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656
E00670 or U00670
E00677 or U00677
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700
E00800 or U00800
E00810 or U00810
E00900 or U00900
E00910 or U00910
E01000 or U01000
E01000 or U01000
CS1650, CS2050, CS2550
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
CS1650, CS2050, CS2550
Fax Communication Error: Power was cut off during communication.
CS1650, CS2050, CS2550
Fax Communication Error: There was no file to transmit in the memory transmission mode.
CS1650, CS2050, CS2550
CS1650, CS2050, CS2550
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
CS1650, CS2050, CS2550
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
CS1650, CS2050, CS2550
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS1650, CS2050, CS2550
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001
E01010 or U01010
E01011 or U01011
E01012 or U01012
E01013 or U01013
E01014 or U01014
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015
E01016 or U01016
E01017 or U01017
E01018 or U01018
E01019 or U01019
E01020 or U01020
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
E01021 or U01021
E01022 or U01022
E01023 or U01023
E01024 or U01024
E01025 or U01025
E01026 or U01026
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01027 or U01027
E01028 or U01028
E01040 or U01040
E01041 or U01041
E01042 or U01042
E01043 or U01043
E01044 or U01044
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
E01045 or U01045
E01046 or U01046
E01047 or U01047
E01048 or U01048
E01049 or U01049
E01050 or U01050
E01051 or U01051
E01052 or U01052
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053
E01054 or U01054
E01055 or U01055
E01056 or U01056
E01057 or U01057
E01070 or U01070
E01071 or U01071
E01072 or U01072
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brak in loop current was detected during transmission.
E01073 or U01073
E01080 or U01080
E01091 or U01091
E01092 or U01092
E01100 or U01100
E01101 or U01101
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
CS1650, CS2050, CS2550
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102
E01110 or U01110
E01111 or U01111
E01112 or U01112
E01113 or U01113
E01114 or U01114
E01115 or U01115
E01116 or U01116
E01117 or U01117
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
E01119 or U01119
E01120 or U01120
E01121 or U01121
E01122 or U01122
E01123 or U01123
E01124 or U01124
E01125 or U01125
E01126 or U01126
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127
E01128 or U01128
E01129 or U01129
E01140 or U01140
E01141 or U01141
E01142 or U01142
E01143 or U01143
E01144 or U01144
E01145 or U01145
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146
E01147 or U01147
E01148 or U01148
E01149 or U01149
E01150 or U01150
E01151 or U01151
E01152 or U01152
E01153 or U01153
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154
E01155 or U01155
E01160 or U01160
E01161 or U01161
E01162 or U01162
E01163 or U01163
E01164 or U01164
E01170 or U01170
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172
E01191 or U01191
E01199 or U01199
E01400 or U01400
E01500 or U01500
E01600 or U01600
E01700 or U01700
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
CS1650, CS2050, CS2550
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
CS1650, CS2050, CS2550
Fax Communication Error: An invalid one-touch key was specified during communication.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred when called in V.8 mode.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
E01720 or U01720
E01721 or U01721
E01800 or U01800
E01810 or U01810
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820
E02000 or U02000
E02100 or U02100
E02200 or U02200
E02200 or U02200
E02200 or U02200
E02303 or U02303
E02304 or U02304
CS1650, CS2050, CS2550
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in he period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS1650, CS2050, CS2550
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
CS1650, CS2050, CS2550
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
CS1650, CS2050, CS2550
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
CS1650, CS2050, CS2550
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
CS1650, CS2050, CS2550
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
CS1650, CS2050, CS2550
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
E02400 or U02400
E03000 or U03000
E03100 or U03100
E03200 or U03200
E03200 or U03200
E03300 or U03300
E03300 or U03300
E03400 or U03400
E03500 or U03500
E03500 or U03500
CS1650, CS2050, CS2550
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
CS1650, CS2050, CS2550
Fax Communication Error: No document was present in the destination unit when polling reception started.
CS1650, CS2050, CS2550
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS1650, CS2050, CS2550
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS1650, CS2050, CS2550
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS1650, CS2050, CS2550
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
CS1650, CS2050, CS2550
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
CS1650, CS2050, CS2550
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500
E03600 or U03600
E03600 or U03600
E03700 or U03700
E03700 or U03700
E04000 or U04000
E04000 or U04000
E04000 or U04000
E04100 or U04100
E04100 or U04100
CS1650, CS2050, CS2550
Fax Communication Error: The destination was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS1650, CS2050, CS2550
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: The destination was being accessed.
CS1650, CS2050, CS2550
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
CS1650, CS2050, CS2550
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
E04200 or U04200
E04300 or U04300
E04400 or U04400
E04401 or U04401
E04500 or U04500
E05000 or U05000
E05100 or U05100
E05200 or U05200
CS1650, CS2050, CS2550
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS1650, CS2050, CS2550
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
CS1650, CS2050, CS2550
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS1650, CS2050, CS2550
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
CS1650, CS2050, CS2550
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
CS1650, CS2050, CS2550
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
CS1650, CS2050, CS2550
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
CS1650, CS2050, CS2550
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300
E09000 or U09000
E12000 or U12000
E12000 or U12000
E12100 or U12100
E14000 or U14000
E14000 or U14000
E14100 or U14100
E14100 or U14100
E19000 or U19000
E19100 or U19100
E19200 or U19200
CS1650, CS2050, CS2550
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
CS1650, CS2050, CS2550
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS1650, CS2050, CS2550
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
CS1650, CS2050, CS2550
Fax Communication Error: In subaddress-based relay reception memory overflowed.
CS1650, CS2050, CS2550
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed during confidential reception.
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed during memory reception.
CS1650, CS2050, CS2550
Fax Communication Error: Memory overflowed in the destination unit during transmission.
CS1650, CS2050, CS2550
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
E19400 or U19400
CS1635 The copier is in Low Power Mode.
CS1635 The copier is in Sleep Mode.
CS1635 Job Accounting is enabled.
There is no paper in the cassette.
CS1635 "Add Toner."
An error has occurred.
CS1635 "Call service. C####" An error has occurred. See above:
CS1650, CS2050, CS2550
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
CS1650, CS2050, CS2550
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
"- - -" appears in the copy quantity display
"-" appears in the copy quantity display
"= = =" appears in copy quantity display
CS1650, CS2050, CS2550
"Add paper in cassette ## size (###)."
Print data does not match the size or type of paper in the cassette. Replace the paper.
CS1635, CS1650, CS2050, CS2550
"Add paper in cassette #."
Copies cannot be produced because there is no toner.
CS1650, CS2050, CS2550
"Call for service. C####"
CS1635
CS1635
"Check paper size."
CS2550
"Checksum Error"
The slit glass is dirty.
"Close ## cover." The indicated cover is open."
CS1635
CS1635 The Document Processor is open.
CS1635 "Close front cover." The front cover of the copier is open.
CS1635 "Close left cover #." The left cover of the cassette is open.
"Cannot copy this paper size."
An original that cannot be copied has been set. 1) The original was set in a vertical direction during the Book Border Erase copying operation. 2) An irregular size original was set during Border Erase or Combine mode operation. 3) An original size other than Letter, Ledger, A3, A4R, A5R, B4, or B5R was set to make a split copy or duplex copy from a double page spread original.
"Cannot duplex this paper size."
Duplex copies cannot be made when A6R, B6R, Postcard, Irregular Size, or the paper size has not been specified.
CS1650, CS2050, CS2550
"Cannot staple this size."
Stapling of small paper, such as Statement, A5R, an B5R is not possible.
CS1650, CS2050, CS2550
There is no paper loaded of a size that can be used in the current selected mode.
"Check the Toner Container."
Toner inside the container shifts to one side.
CS1650, CS2050, CS2550
The machine has detected an error at startup.
CS1650, CS2050, CS2550
"Clean the slit glass for original fed from
DP."
CS1650, CS2050, CS2550
"Close document processor cover."
The left cover of the document processor is open.
"Close document processor."
CS1650, CS2050, CS2550
"Exceed copy limit. Unable to copy."
The number of copies made with your management code has reached the limit that was set in the department management mode, and copying is no longer possible with that code.
CS1635 "Insert Key Counter" Check the key counter.
"Interface occupied."
CS1635
CS1635
CS1635 Memory is full.
CS1650, CS2050, CS2550
"Format error Memory card."
An unformatted memory card has been inserted, or when the machine has tried to read data from the memory card the memory card is not recognized.
CS1650, CS2050, CS2550
"Insert same memory card."
When the machine has tried to read data from the memory card, the memory card is not recognized.
CS1650, CS2050, CS2550
The selected interface is currently being used.
"Main Power Off/On A####"
A customer recoverable error code has occurred.
CS1650, CS2050, CS2550
"Memory card error. Insert again."
The memory card is accidentally removed during printer setting.
"Memory is full. Cannot continue."
Copies cannot be produced because memory is full during the interrupt copy operation. Interrupt copying cannot be carried out.
"Memory is full. Press OK."
CS1650, CS2050, CS2550
"Memory is full." when copying.
Current copying cannot be processed because the memory for copying is full or the number of originals has reached the limit of 999 pages. Depending on the copy setting conditions, only one set of copies may be output, and this error message may be displayed even if a multiple number of copies is specified. In this case, copying cannot be continued.
"Misfeed in DP."
CS1635 Check the MP Tray paper.
CS1635
CS1635 "Paper jam." A paper misfed has occurred.
"Paper misfeed." A paper misfed has occurred.
CS1635 An original has misfed.
CS1650, CS2050, CS2550
"Memory is full." when printing.
Current printing cannot be processed because the memory for printing is full.
CS1650, CS2050, CS2550
"MemoryCard err. Press GO."
An error has occurred in writing to or reading from the memory card.
CS1650, CS2050, CS2550
Originals have jammed in the optional document processor.
"MP tray empty. Add paper."
"No matching paper available."
No letter/A4 paper was available in either cassette or the MP tray when a report was attempted to be output.
CS1650, CS2050, CS2550
"Out of Staples. Please Add Staples."
There are no staples left in the optional finisher.
CS1650, CS2050, CS2550
"Paper capacity exceeded. Remove
paper from Job sep." when copying.
100 copies have accumulated on the optional job separator.
CS1650, CS2050, CS2550
"Paper misfeed in the Finisher, lower
Process Tray and remove paper.
Paper has jammed in the optional finisher.
CS1650, CS2050, CS2550
"Place the original on the DP."
CS1635
The waste toner box is full.
CS1650, CS2050, CS2550
"Print overrun. Press GO."
Printing has not been performed properly because of insufficient memory.
CS1650, CS2050, CS2550
"RAM disk error. Press GO."
An error has occurred in writing to or reading from the RAM disk.
CS1650, CS2050, CS2550
"Ready to copy. Add toner."
Toner remaining in the machine is low. It is possible to copy only one by one.
CS1650, CS2050, CS2550
"Remove paper from Finisher. Press
START key." when copying.
250 copies have accumulated on the finisher tray.
CS1650, CS2050, CS2550
"Remove paper from the Finisher. Press GO." when printing.
250 prints have accumulated on the finisher tray.
CS1650, CS2050, CS2550
"Remove paper from the Top tray. Press GO." when printing.
250 prints have accumulated on the output tray. Or 150 copies have accumulated on the output tray with job separator installed. Or 100 copies have accumulated on the output tray when the optional finisher is installed.
CS1650, CS2050, CS2550
"Remove paper from the Top tray. Press START key." when
copying.
250 copies have accumulated on the output tray. Or 150 copies have accumulated on the output tray with job separator installed. Or 100 copies have accumulated on the output tray when the optional finisher is installed.
"Remove paper on top tray; Start."
250 copies have accumulated on the output tray.
CS1635, CS1650, CS2050, CS2550
"Replace waste toner box."
CS1650, CS2050, CS2550
"Reposition original or change cassette."
The orientations of the original and the selected paper are different.
CS1635
CS1635
"Set paper cassette"
"Set toner container."
It is time for Periodic Maintenance.
No toner remains.
CS1635 There is very little toner remaining.
CS1635
CS1635 It is time for Periodic Maintenance.
"Reseat originals on the DP."
Originals were set in the optional Document Processor when copying 2-sides, when copying from the platen in 2-sided copy, 2 in 1, 4 in 1, or when collating copies.
CS1650, CS2050, CS2550
"Reset all originals in DP."
If the optional Document Processor is being used, there are originals left on the originals table.
"Return all originals to DP."
If the optional Document Processor is being used, there are originals left on the originals table.
CS1635, CS1650, CS2050, CS2550
Check the paper cassette that corresponds to the lighting indicator.
CS1635, CS1650, CS2050, CS2550
The toner container has not been set properly.
CS1650, CS2050, CS2550
"System Error. Main switch Off/On." when
printing.
A malfunction has occurred due to noise or a communication error occurred during printer processing.
CS1650, CS2050, CS2550
"Time fo maintenance."
CS1650, CS2050, CS2550
"Unable to copy. Please add toner."
Add Toner indicator blinks On and Off
Periodic Maintenance indicator blinks On
and Off
This is a notification that the time for periodic maintenance is approaching.
Periodic Maintenance indicator lights solid
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > +/- zoom to "On" > Start > Stop/Clear > 1 > Start.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163
10871087 163
10871087 163
Use +/- Zoom keys to 163 > Start > "CLE" for 1635 or ^/v to "Execute" for 2550 > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > ^/v to "Execute" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > "CLE" for 1635 or ^/v to "Execute" for 1650/2050/2550 > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
10871087 163
10871087 163
10871087 163
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
Use +/- Zoom keys to 163 > Start > "CLE" for 1635 or ^/v to "Execute" for 1650/2050/2550 > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > "CLE" for 1635 or ^/v to "Execute" for 1650/2050/2550 > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 163 > Start > ^/v to "Execute" > Start > Stop/Clear > +/- Zoom to 001 > Start (to exit).
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
10871087 906
10871087 906
Turn power Off/On.
Turn power Off/On.Turn power Off/On.
Turn power Off/On.Turn power Off/On.
Turn power Off/On.
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Use +/- Zoom keys to 906 > Start > ^/v to select Execute > Start.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Service Checks1) Repl fax control PWB.
1) Upgrade firmware to compatible versions.
1) Repl main PWB.
1) Run simulation U020, 2) Repl main PWB.
1) Repl drum EEPROM, 2) Repl main PWB.
1) Repl EEPROM, 2) Repl main PWB.
1) Reload firmware, 2) Repl engine PWB.
1) Repl engine PWB, 2) Repl main PWB.
1) Run simulation U020, 2) Repl EEPROM, 3) Repl main PWB.
1) Run simulation U020, 2) Repl engine PWB.
1) Contact Kyocera Service Administrative Division, 2) Install the correct EEPROM, 3) Repl engine PWB, 4) Repl main PWB.
1) Reseat YC6 @ main PWB, 2) Reseat YC1 @ engine PWB, 3) Repl engine PWB, 4) Repl main PWB.
1) Repl main PWB.
1) Repl engine PWB.
1) Repl main PCB.
1) Reseat interface PWB to printer PWB, 2) Repl printer PWB. 3) Repl main PWB.
1) Reseat scanner network board, 2) Repl scanner network PWB, 3) Repl main PWB.
1) Reseat fax control PCB (YC1 @ fax PWB & YC15 @ main PWB), 2) Repl fax control PCB, 3) Repl main PWB.
1) Reseat DP connectors, 2) Repl DP driver PWB, 3) Repl main PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main PWB.
1) Reseat DF connectors, 2) Repl finisher main PCB, 3) Repl main PCB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main PWB.
1) Reseat PF connectors, 2) Repl PF main PWB, 3) Repl main PWB.
1) Reseat DIMM on main PWB, 2) Repl DIMM on main PWB, 3) Repl main PWB.
1) Reseat DIMM on main PWB, 2) Repl main PWB.
1) Repl fax control PCB.
1) Repl fax control PCB.
1) Repl fax control PWB.
1) Repl fax control PCB.
1) Upgrade firmware to compatible versions.
1) Repl fax control PCB.
1) Upgrade fax firmware to version 2.xx or later, 2) Repl fax control PCB.
1) Reseat fax control PCB (YC1 @ fax control PCB & YC15 @ main PCB, 2) Repl fax control PCB, 3) Repl main PCB.
1) Repl developing unit EEPROM, 2) Repl main PCB.
1) Reseat drive motor connectors, 2) Check drive components for excessive drag, 3) Repl drive motor.
1) Reseat scanner motor connectors, 2) Check scanner drive components for excessive drag, 3) Check/repl scanner HPS, 4) Repl scanner motor, 5) Repl engine PCB.
1) Reseat lamp circuit connectors, 2) Repl exposure lamp & inverter PCB, 3) Adjust shading plate detection position, 4) Check/repl scanner HPS, 5) Repl engine PCB.
1) Repl exposure lamp & inverter PCB, 2) Adjust shading plate detection position, 3) Check/repl scanner HPS, 4) Repl engine PCB, 5) Repl ISU (CCD).
1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat laser unit connectors, 2) Repl laser unit, 3) Repl engine PWB, 4) Repl main PWB.
1) Check that thermistor is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters.
1) Check that thermistor is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters.
1) Check that thermistor is contacting fuser roller and clean, 2) Replace thermistor, 3) Repl power supply PWB.
1) Reseat fixing unit connector.
1) Reseat the drum unit, 2) Repl drum unit.
1) Check fixing heaters 2) Check that thermistor is contacting heat roller & clean, 3) Check thermal switch.
1) Check wall outlet ground to neutral voltage. 2) Check YC2-5 @ PSU for zero-crossing signal. If absent repl PSU, 3) If zero-crossing signal is present repl Engine PWB.
1) Reseat the developing unit, 2) Repl developing unit.
1) Reload engine PWB firmware. 2) Replace Engine PWB.
1) Reload engine PWB firmware. 2) Replace Engine PWB.
1) Reseat humidity sensor connector, 2) Repl the Drawer PWB.
1) Reseat humidity sensor connector, 2) Repl the Drawer PWB.
1) Reseat connector or replace front registration motor, 2) Reseat connector or replace front registration HPS, 3) Repl finisher main PCB.
1) Reseat connector or replace rear registration motor, 2) Reseat connector or replace rear registration HPS, 3) Repl finisher main PCB.
1) Repl main PWB.
1) Repl main PWB.1) Replace engine PWB, 2) Repl main PWB.
1) Repl engine PWB.
Load paper.
1) Reseat connector or replace trailing edge registration motor, 2) Reseat connector or replace trailing edge registration HPS, 3) Repl finisher main PCB.
1) Reseat stapler connector, 2) Remove jammed staples & confirm proper staple installation, 3) Repl stapler, 4) Repl finisher main PCB.
1) Repl main PWB, 2) Repl operation panel PWB.
1) Repl expansion memory, 2) Repl main PWB.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Press [Energy Saver] to exit sleep mode.
Replace the toner container with a new one.
Press any key to exit Low Power Mode, or in the case where the optional Document Processor is installed, set an original in the Document Processor.
Use the numeric keys to enter the assigned Section Code to perform copying operations. Press [Job Accounting] after copying is finished to display "= = =" again.
To change the paper source, press [Paper Select] key to select desired paper source and press [Enter] key. If you press [Printer] key, the following messages are displayed: GO: Prints onto the currently selected paper, CANCEL: Stops printing. Press ^/v key to select desired paper tray and press [Enter] key.
Load paper into the cassette as displayed in place of #.
Open the front cover once and close it. If the message is displayed again note the 5 digit error number. Contact service.
Specify a paper size that can be used.
Check the paper.
Close all the covers securely.
Close the left cover, close the front cover.
Close the Document Processor.
Close the front cover.
Check the original. 1) Set the original horizontally. 2) Back the irregular original with a standard sized white piece of paper. 3) Back the irregular original with a standard sized white piece of paper.
Select a larger paper size or turn Off stapling.
Turn the gear on the toner container to even out the toner level in the container.
Main power Off/On to reset. If re-occurs call service.
Clean the slit glass because black lines may be copied when the optional document processor is used.
Close the left cover as displayed in place of #.
Contact your system administrator. Use the department management mode to clear the copy count.
Make sure the key counter is set properly.
Wait for a while and retry.
Power Off. Insert memory card. Power On.
Format the memory card. If the formatting fails, the card may be corrupt/defective.
Power Off. Re-insert memory card. Power On.
Turn power switch Off/On. Usage will be possible again once the regular display returns. If the code re-occurs, note the error code, and contact service.
Press [Stop/Clear], then [Interrupt] again after the data read in has been deleted, to exit the Interrupt Copying. After the copying operation for the interrupted copy has been complete, repeat the procedure again.
Press [OK] to start outputting the copies read in. Press [Reset} or [Stop/Clear] to delete the data read in. Reduce the number of originals and repeat the copying procedure.
Select [Copy Scanned Image] to output the pages that have been scanned, or press [Cancel] to delete scanned data. Press the [Enter] key and perform copying operation again. If this error occurs frequently, additional memory is recommended.
Add staples.
Remove the paper. Copying will resume.
Remove the jammed paper.Remove the paper.
Press the [Printer] key to display these messages: GO: Continues printing. CANCEL: Cancels printing. RESET: Resets the printer board. Only the printer functions will be reset. If using RAM Disk function reduce the size of the RAM disk. If this error occurs frequently, additional memory is recommended.
Press [Printer], select [GO], and press [Enter]. The error will be cleared.
Leave the main power switch On, and follow the appropriate procedure to remove the jammed originals.
Set paper in the MP Tray in the event there is no paper present there. When the MP Tray paper fails to be fed, reset the paper.
Press [Paper Selection] and select the supply cassette, then press [Start]. Paper will be supplied from the cassette selected.
The location of the jam is indicated on the message display, and the machine stops.Leave the main power switch On and folow the appropriate procedure to remove the jammed paper.
The copier will try to make copies of the originals it could not copy before. Return all originals to the originals table and try copying them again.
Remove the paper. Copying will resume.
Remove the paper. Copying will resume.
Replace it with a new waste toner box.
Press the [Printer] key to display these messages: GO: Continues printing. CANCEL: Cancels printing. RESET: Resets the printer board. Only the printer functions will be reset. If this error occurs frequently, additional memory is recommended.
Press [Printer], select [GO], and press [Enter]. The error will be cleared.
Replace the toner container as soon as possible.
Remove the paper. Press [Printer], then ^/v key to select [GO], then [Enter] to resume printing. Select [CANCEL], then [Enter] to cancel printing.
Remove the paper. Press [Printer], then ^/v key to select [GO], then [Enter] to resume printing. Select [CANCEL], then [Enter] to cancel printing.
Remove the paper, press [Start] and resume copying.
Change the orientation of the original. If you press [Start] key without changing the orientation, copying will be performed at 100% (1:1) magnification ratio.
Set the toner container properly.
Contact your service representative.
Replace the toner container.
Contact your service representative.
Remove the originals from the Document Processor. Replace the originals on the original table after exiting the front and back copying, 2-sided copy, 2 in 1, 4 in 1, or Collate Mode and resume copying.
Remove the originals, return them to the original table and try copying them again.
Remove the originals, return them to the original table and try copying them again.
Set the cassette. First pull it out and push it all the way back in.
Clear the print queue. Main power Off, wait more than 5 seconds, then main power On. Attempt printing again.
Copying can be continued for a short while before running out of toner. Replace the toner container with a new one as soon as possible.
Model Error Code Description0xFBxx Undefined.
CS-2540, CS-3040 C0030
C0060 Main PWB Type Mismatch Error.
CS-2540, CS-3040 C0070
CS-2540, CS-3040 C0100
CS-2540, CS-3040 C0110
C0120
C0130
CS-2540, CS-3040 C0140
C0150
C0160
CS-2540, CS-3040 C0170
C0180
CS-2540 (2JB), CS-3040 (2JC), CS-2560
(2HO), CS-3060 (2HZ)
Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.
CS-2540, CS-3040, CS-2560, CS-3060
Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software.
Main PWB Backup Memory Device Problem. Writing or erasing has not completed even after a certain time.
Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS-2540, CS-3040, CS-2560, CS-3060
Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-2540, CS-3040, CS-2560, CS-3060
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
CS-2540, CS-3040, CS-2560, CS-3060
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
CS-2540, CS-3040, CS-2560, CS-3060
Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively.
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
CS-2540, CS-3040, CS-2560, CS-3060
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
CS-2540, CS-3040 C0210
CS-2540, CS-3040 C0240
CS-2540, CS-3040 C0280
C0320
C0420
C0440
C0440
CS-2540, CS-3040 C0610
CS-2540, CS-3040 C0630
CS-2560, CS-3060 C0640
CS-2560, CS-3060 C0700 Optional fax CF backup is not suitable.
CPU Communication Problem. There is no reply after 3 tries at communication.
Printer PWB Printer Communication Problem. The printer PWB does not respond within 120 sec of power On.
Communication Problem between the Fax Control PWB and Main PWB. Fax control PWB does not transmit the key required command within 3 minutes of Main PWB change status signal to On. One time it resets the fax. If the key required command is not transmitted within 1 additional minute an error occurs. When FAX_READY continues to fake for 6 sec, one time it resets the fax. If FAX_READY continues to fake for 6 additional seconds, an error occurs.
CS-2540, CS-3040, CS-2560, CS-3060
Power CPU Communication Problem. Engine PWB and Power CPU are unable to communicate.
CS-2540, CS-3040, CS-2560, CS-3060
PF-670 Communication Problem. Engine PWB and Paper Feeder are unable to communicate with each other.
CS-2540, CS-3040, CS-2560, CS-3060
DF-670 Communication Problem. Finisher and Engine PWB are unable to communicate.
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 Communication Problem. Finisher and Engine PWB are unable to communicate.
Bitmap Problem. The DIMM on the main PWB does not operate correctly.
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
Hard Disk Drive Problem. HDD cannot be accessed
C0800
CS-2540, CS-3040 C0820
CS-2540, CS-3040 C0830
CS-2540, CS-3040 C0860
CS-2540, CS-3040 C0870
CS-2540, CS-3040 C0880
CS-2540, CS-3040 C0890
CS-2540, CS-3040 C0920
C0960
C1010
CS-2540, CS-3040, CS-2560, CS-3060
Image processing problem. JAM05 is detected twice.
Fax Control PWB CG ROM Checksum Error. A checksum error occurred with the CG ROM data of the fax control PWB.
Fax Control PWB Flash Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
Fax Control PWB Software Switch Checksum Error. A checksum error occurred with the software switch value of the fax control PWB.
Fax Control PWB to Main PWB High Capacity Data Transfer Problem. High capacity data transfer between the fax control PWB and the scanner MIP PWB was not performed normally after 10 retries.
Program Archive Problem. At initialization the compressed program in the Flash ROM on the fax control PWB was not successfully decompressed.
Fax Control PWB CG Font Archive Problem. At initialization the compressed CG font in the Flash ROM on the fax control PWB was not successfully decompressed.
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of fax ctrol PWB.
CS-2540, CS-3040, CS-2560, CS-3060
Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-2540, CS-3040, CS-2560, CS-3060
Cassette #1 Lift Motor error. Upper lift limit switch remains low after 12 seconds of operation.
C1020
C1030
C1040
C2000
C2200
C2500
C2600
C3100
C3200
CS-2540, CS-3040, CS-2560, CS-3060
Cassette #2 Lift Motor error. Lower lift limit switch remains low after 12 seconds of operation.
CS-2540, CS-3040, CS-2560, CS-3060
PF-670 optional cassette #3 lift motor error. PF lift limit switch 1 remains low after 12 seconds of operation.
CS-2540, CS-3040, CS-2560, CS-3060
PF-670 optional cassette #4 lift motor error. PF lift limit switch 2 remains low after 12 seconds of operation.
CS-2540, CS-3040, CS-2560, CS-3060
Main Motor Problem. Stable Off is detected exceeding 1 sec after motor stability.
CS-2540, CS-3040, CS-2560, CS-3060
Drum Motor Problem. Stable Off is detected exceeding 1 sec after drum motor stability.
CS-2540, CS-3040, CS-2560, CS-3060
Paper Feed Motor error. Stable Off is detected exceeding 1 sec after paper feed motor stability.
CS-2540, CS-3040, CS-2560, CS-3060
PF-670 Drive Motor error. Lock signal exceeds 500ms.
CS-2540, CS-3040, CS-2560, CS-3060
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
CS-2540, CS-3040, CS-2560, CS-3060
Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading.
CS-2540, CS-3040 C3300
CS-2560, CS-3060 C3300
CS-2560, CS-3060 C3500
C4000
C4010
CS-2540, CS-3040 C4200
CS-2560, CS-3060 C4200
C6000
C6020
C6050
C6120
C6150
C6400
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
Communication Error Between Scanner and SHD.
CS-2540, CS-3040, CS-2560, CS-3060
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
CS-2540, CS-3040, CS-2560, CS-3060
Polygon Motor Steady-State Problem. Stable Off is detected for 5 sec continuously after polygon motor stabilization.
BD Steady-State Problem. ASIC detects a Beam Detect error for 1 sec after polygon motor stabilization.
BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization.
CS-2540, CS-3040, CS-2560, CS-3060
Fuser Heater Break. Thermistor1 detected less than 40C/104F for 10 sec during warmup & ready.
CS-2540, CS-3040, CS-2560, CS-3060
Abnormally High Center Thermistor Temperature. Thermistor 2 is detected 230C/446F for 40ms or more.
CS-2540, CS-3040, CS-2560, CS-3060
Abnormally Low Center Thermistor Temperature. Thermistor 2 is detected 100C/212F or less for 1 sec continuously during copying.
CS-2540, CS-3040, CS-2560, CS-3060
Abnormally High Edge Thermistor Temperature. Thermistor 1 is detected 230C/446F for 40ms or more.
CS-2540, CS-3040, CS-2560, CS-3060
Abnormally Low Edge Thermistor Temperature. Thermistor 1 is detected 100C/212F or less for 1 sec continuously during copying.
CS-2540, CS-3040, CS-2560, CS-3060
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
C6420
C7000
C7200
C7300
C7400
C7410
C7800
C8030
CS-2540, CS-3040 C8140
CS-2560, CS-3060 C8140
C8170
CS-2540, CS-3040, CS-2560, CS-3060
Fuser Unit Fuse Cut Problem. The fuse has been cut 3 sec after the fuse cut signal is turned on.
CS-2540, CS-3040, CS-2560, CS-3060
Toner Motor Problem. An overcurrent signal is detected exceeding 1 sec.
CS-2540, CS-3040, CS-2560, CS-3060
Broken Inner Thermistor Wire. An abnormal value is detected in the input data from the inner thermistor.
CS-2540, CS-3040, CS-2560, CS-3060
Toner Hopper Problem. Toner emptiness is detected for 300 sec, three times during toner replenishment.
CS-2540, CS-3040, CS-2560, CS-3060
Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.
CS-2540, CS-3040, CS-2560, CS-3060
Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
CS-2540, CS-3040, CS-2560, CS-3060
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.
DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 20 sec.
DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec.
CS-2540, CS-3040, CS-2560, CS-3060
DF-670 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8170
C8180
C8190
C8210
C8210
C8440
C8460
C9000
C9060
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation. Adjustment home position sensor is not On at activation.
CS-2540, CS-3040, CS-2560, CS-3060
DF-670 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
CS-2540, CS-3040, CS-2560, CS-3060
DF-670 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
CS-2540, CS-3040, CS-2560, CS-3060
DF-670 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 Stapler Problem. Home position is not detected within a specific time of activation.
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
CS-2540, CS-3040, CS-2560, CS-3060
DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed.
CS-2540, CS-3040, CS-2560, CS-3060
DP-670 Communication Problem. A communication error is detected.
CS-2540, CS-3040, CS-2560, CS-3060
DP-670 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
CF1xx Undefined.
CF2xx Undefined.
CF3xx Undefined.
CF4xx Undefined.
CF5xx Undefined.
CF610 Undefined.
CF620 Unable to Print.
CF6xx Undefined.
CF7xx Undefined.
CFAxx HDD Error.
CFB2C Undefined.
CFB30
CFB31 Corrupt Firmware on Main EEPROM.
CFBxx Undefined.
F000
F010 Main PWB Checksum Error.
F020 Memory Checksum Error.
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
Incompatible Level Of Firmware on Main EEPROM.
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
Operation Panel PWB Communication Error.
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
F030 Main PWB System Error.
F040 Engine PWB Communication Error.
F041 Scanner PWB Communication Error.
F050 Engine ROM Checksum Error.
F060 Engine RAM Error.
F070 Flash ROM Error.
F080 Flash ROM Error (during download).
F090 Fax Control PWB Communication Error.
F14F Power Source PWB Second Side Error.
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
E00000 or U00000
Fax Communication Error: No response or line busy after the set number of redials.
CS-2540, CS-3040, CS-2560, CS-3060
E00100 or U00100
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
CS-2540, CS-3040, CS-2560, CS-3060
E00200 or U00200
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
CS-2540, CS-3040, CS-2560, CS-3060
E00300 or U00300
Fax Communication Error: Recording paper on the destination unit has run out during reception.
CS-2540, CS-3040, CS-2560, CS-3060
E00420 or U00420
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
CS-2540, CS-3040, CS-2560, CS-3060
E00421 or U00421
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
CS-2540, CS-3040, CS-2560, CS-3060
E00430 or U00430
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
CS-2540, CS-3040, CS-2560, CS-3060
E00430 or U00430
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
CS-2540, CS-3040, CS-2560, CS-3060
E00431 or U00431
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00431 or U00431
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00432 or U00432
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
CS-2540, CS-3040, CS-2560, CS-3060
E00432 or U00432
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS-2540, CS-3040, CS-2560, CS-3060
E00433 or U00433
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
CS-2540, CS-3040, CS-2560, CS-3060
E00433 or U00433
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
CS-2540, CS-3040, CS-2560, CS-3060
E00434 or U00434
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
CS-2540, CS-3040, CS-2560, CS-3060
E00435 or U00435
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E00435 or U00435
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E00440 or U00440
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00440 or U00440
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E00441 or U00441
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
CS-2540, CS-3040, CS-2560, CS-3060
E00450 or U00450
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E00460 or U00460
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00460 or U00460
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E00462 or U00462
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E00500 or U00500
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
CS-2540, CS-3040, CS-2560, CS-3060
E00600 or U00600
Fax Communication Error: The document processor cover is open.
CS-2540, CS-3040, CS-2560, CS-3060
E00601 or U00601
Fax Communication Error: Document jam or the document length exceeds the maximum.
CS-2540, CS-3040, CS-2560, CS-3060
E00602 or U00602
Fax Communication Error: Image scanning section problem
CS-2540, CS-3040, CS-2560, CS-3060
E00603 or U00603
Fax Communication Error: No document feed.
CS-2540, CS-3040, CS-2560, CS-3060
E00604 or U00604
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS-2540, CS-3040, CS-2560, CS-3060
E00610 or U00610
Fax Communication Error: Recording section cover open.
CS-2540, CS-3040, CS-2560, CS-3060
E00611 or U00611
Fax Communication Error: Recording paper jam.
CS-2540, CS-3040, CS-2560, CS-3060
E00613 or U00613
Fax Communication Error: Image writing section problem.
CS-2540, CS-3040, CS-2560, CS-3060
E00614 or U00614
Fax Communication Error: Nearly empty of recording paper.
CS-2540, CS-3040, CS-2560, CS-3060
E00615 or U00615
Fax Communication Error: Empty of recording paper.
CS-2540, CS-3040, CS-2560, CS-3060
E00620 or U00620
Fax Communication Error: Copier fixing unit problem.
CS-2540, CS-3040, CS-2560, CS-3060
E00622 or U00622
Fax Communication Error: Copier drive motor problem.
CS-2540, CS-3040, CS-2560, CS-3060
E00655 or U00655
Fax Communication Error: CTS was not activated after RTS due to a modem error.
CS-2540, CS-3040, CS-2560, CS-3060
E00656 or U00656
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
CS-2540, CS-3040, CS-2560, CS-3060
E00670 or U00670
Fax Communication Error: Power was cut off during communication.
Fax Communication Error: System error.
CS-2540, CS-3040, CS-2560, CS-3060
E00677 or U00677
Fax Communication Error: There was no file to transmit in the memory transmission mode.
CS-2540, CS-3040, CS-2560, CS-3060
E00690 or U00690
CS-2540, CS-3040, CS-2560, CS-3060
E00700 or U00700
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E00800 or U00800
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
CS-2540, CS-3040, CS-2560, CS-3060
E00810 or U00810
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
CS-2540, CS-3040, CS-2560, CS-3060
E00900 or U00900
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS-2540, CS-3040, CS-2560, CS-3060
E00910 or U00910
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
CS-2540, CS-3040, CS-2560, CS-3060
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
CS-2540, CS-3040, CS-2560, CS-3060
E01000 or U01000
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
CS-2540, CS-3040, CS-2560, CS-3060
E01001 or U01001
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01010 or U01010
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01011 or U01011
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
CS-2540, CS-3040, CS-2560, CS-3060
E01012 or U01012
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01013 or U01013
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01014 or U01014
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
CS-2540, CS-3040, CS-2560, CS-3060
E01015 or U01015
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
CS-2540, CS-3040, CS-2560, CS-3060
E01016 or U01016
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
CS-2540, CS-3040, CS-2560, CS-3060
E01017 or U01017
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
CS-2540, CS-3040, CS-2560, CS-3060
E01018 or U01018
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
CS-2540, CS-3040, CS-2560, CS-3060
E01019 or U01019
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01020 or U01020
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01021 or U01021
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01022 or U01022
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01023 or U01023
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01024 or U01024
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01025 or U01025
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01026 or U01026
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01027 or U01027
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01028 or U01028
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01040 or U01040
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01041 or U01041
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01042 or U01042
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01043 or U01043
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01044 or U01044
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01045 or U01045
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01046 or U01046
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01047 or U01047
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01048 or U01048
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01049 or U01049
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01050 or U01050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01051 or U01051
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01052 or U01052
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01053 or U01053
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01054 or U01054
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01055 or U01055
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01056 or U01056
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01057 or U01057
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01070 or U01070
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
CS-2540, CS-3040, CS-2560, CS-3060
E01071 or U01071
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E01072 or U01072
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E01073 or U01073
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01080 or U01080
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01091 or U01091
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
CS-2540, CS-3040, CS-2560, CS-3060
E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
CS-2540, CS-3040, CS-2560, CS-3060
E01100 or U01100
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01101 or U01101
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01102 or U01102
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
CS-2540, CS-3040, CS-2560, CS-3060
E01110 or U01110
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01111 or U01111
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01112 or U01112
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01113 or U01113
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01114 or U01114
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01115 or U01115
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01116 or U01116
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01117 or U01117
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01118 or U01118
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01119 or U01119
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
CS-2540, CS-3040, CS-2560, CS-3060
E01120 or U01120
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01121 or U01121
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01122 or U01122
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01123 or U01123
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01124 or U01124
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01125 or U01125
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
CS-2540, CS-3040, CS-2560, CS-3060
E01126 or U01126
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01127 or U01127
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01128 or U01128
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01129 or U01129
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
CS-2540, CS-3040, CS-2560, CS-3060
E01140 or U01140
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01141 or U01141
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01142 or U01142
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01143 or U01143
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01144 or U01144
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01145 or U01145
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
CS-2540, CS-3040, CS-2560, CS-3060
E01146 or U01146
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
CS-2540, CS-3040, CS-2560, CS-3060
E01147 or U01147
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01148 or U01148
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01149 or U01149
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
CS-2540, CS-3040, CS-2560, CS-3060
E01150 or U01150
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01151 or U01151
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01152 or U01152
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01153 or U01153
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01154 or U01154
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
CS-2540, CS-3040, CS-2560, CS-3060
E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
CS-2540, CS-3040, CS-2560, CS-3060
E01160 or U01160
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
CS-2540, CS-3040, CS-2560, CS-3060
E01161 or U01161
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01162 or U01162
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01163 or U01163
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01164 or U01164
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01170 or U01170
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
CS-2540, CS-3040, CS-2560, CS-3060
E01172 or U01172
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E01191 or U01191
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
CS-2540, CS-3040, CS-2560, CS-3060
E01199 or U01199
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
CS-2540, CS-3040, CS-2560, CS-3060
E01400 or U01400
Fax Communication Error: An invalid one-touch key was specified during communication.
CS-2540, CS-3040, CS-2560, CS-3060
E01500 or U01500
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS-2540, CS-3040, CS-2560, CS-3060
E01600 or U01600
Fax Communication Error: A communication error occurred when called in V.8 mode.
CS-2540, CS-3040, CS-2560, CS-3060
E01700 or U01700
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
CS-2540, CS-3040, CS-2560, CS-3060
E01720 or U01720
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-2540, CS-3040, CS-2560, CS-3060
E01721 or U01721
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
CS-2540, CS-3040, CS-2560, CS-3060
E01800 or U01800
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
CS-2540, CS-3040, CS-2560, CS-3060
E01810 or U01810
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
CS-2540, CS-3040, CS-2560, CS-3060
E01820 or U01820
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in he period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-2540, CS-3040, CS-2560, CS-3060
E02000 or U02000
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
CS-2540, CS-3040, CS-2560, CS-3060
E02100 or U02100
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
CS-2540, CS-3040, CS-2560, CS-3060
E02200 or U02200
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
CS-2540, CS-3040, CS-2560, CS-3060
E02200 or U02200
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
CS-2540, CS-3040, CS-2560, CS-3060
E02200 or U02200
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
CS-2540, CS-3040, CS-2560, CS-3060
E02303 or U02303
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
CS-2540, CS-3040, CS-2560, CS-3060
E02304 or U02304
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
CS-2540, CS-3040, CS-2560, CS-3060
E02400 or U02400
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
CS-2540, CS-3040, CS-2560, CS-3060
E03000 or U03000
Fax Communication Error: No document was present in the destination unit when polling reception started.
CS-2540, CS-3040, CS-2560, CS-3060
E03100 or U03100
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS-2540, CS-3040, CS-2560, CS-3060
E03200 or U03200
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E03200 or U03200
Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E03300 or U03300
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-2540, CS-3040, CS-2560, CS-3060
E03300 or U03300
Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-2540, CS-3040, CS-2560, CS-3060
E03400 or U03400
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
CS-2540, CS-3040, CS-2560, CS-3060
E03500 or U03500
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
CS-2540, CS-3040, CS-2560, CS-3060
E03500 or U03500
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E03500 or U03500
Fax Communication Error: The destination was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E03600 or U03600
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS-2540, CS-3040, CS-2560, CS-3060
E03600 or U03600
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
CS-2540, CS-3040, CS-2560, CS-3060
E03700 or U03700
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E03700 or U03700
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E04000 or U04000
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E04000 or U04000
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E04000 or U04000
Fax Communication Error: The destination was being accessed.
CS-2540, CS-3040, CS-2560, CS-3060
E04100 or U04100
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
CS-2540, CS-3040, CS-2560, CS-3060
E04100 or U04100
Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.
CS-2540, CS-3040, CS-2560, CS-3060
E04200 or U04200
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS-2540, CS-3040, CS-2560, CS-3060
E04300 or U04300
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
CS-2540, CS-3040, CS-2560, CS-3060
E04400 or U04400
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS-2540, CS-3040, CS-2560, CS-3060
E04401 or U04401
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
CS-2540, CS-3040, CS-2560, CS-3060
E04500 or U04500
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
CS-2540, CS-3040, CS-2560, CS-3060
E05000 or U05000
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
CS-2540, CS-3040, CS-2560, CS-3060
E05100 or U05100
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
CS-2540, CS-3040, CS-2560, CS-3060
E05200 or U05200
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
CS-2540, CS-3040, CS-2560, CS-3060
E05300 or U05300
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
CS-2540, CS-3040, CS-2560, CS-3060
E09000 or U09000
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS-2540, CS-3040, CS-2560, CS-3060
E12000 or U12000
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
CS-2540, CS-3040, CS-2560, CS-3060
E12000 or U12000
Fax Communication Error: In subaddress-based relay reception memory overflowed.
CS-2540, CS-3040, CS-2560, CS-3060
E12100 or U12100
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
CS-2540, CS-3040, CS-2560, CS-3060
E14000 or U14000
Fax Communication Error: Memory overflowed during confidential reception.
CS-2540, CS-3040, CS-2560, CS-3060
E14000 or U14000
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
CS-2540, CS-3040, CS-2560, CS-3060
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E14100 or U14100
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
CS-2540, CS-3040, CS-2560, CS-3060
E19000 or U19000
Fax Communication Error: Memory overflowed during memory reception.
CS-2540, CS-3040, CS-2560, CS-3060
E19100 or U19100
Fax Communication Error: Memory overflowed in the destination unit during transmission.
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2540, CS-3040, CS-2560, CS-3060
E19200 or U19200
Fax Communication Error: Memory transmission failed because a decoding error occurred.
CS-2540, CS-3040, CS-2560, CS-3060
E19300 or U19300
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
CS-2540, CS-3040, CS-2560, CS-3060
E19400 or U19400
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Host name error.
Send SMB Error 1102
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send SMB Error 1103
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send SMB Error 1103
Error: Pathname or File Name. Assign disable folder path.
Send SMB Error 1105
Error: Not Supported Protocol. SMB protocol is set to OFF.
Send SMB Error 2101
Error: Can Not Connect. Enter the disable host name/IP address.
Send SMB Error 2101
Error: Can Not Connect. Assign the wrong port number.
Send SMB Error 2101
Error: Can Not Connect. Network is not connected.
Send SMB Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
Send SMB Error 2201
Error: Network Transfer. Error occurs on the network.
Send SMB Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send SMB Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send FTP Error 1101
Error: Host Name. Enter the disable host name/IP address.
Send FTP Error 1102
Error: Username/Password. Domain name is not entered.
Send FTP Error 1102
Error: Username/Password. Assign disable user/password.
Send FTP Error 1103
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send FTP Error 1103
Error: Pathname or File Name. Assign disable folder path.
Send FTP Error 1105
Error: Not Supported Protocol. FTP protocol is set to OFF.
Send FTP Error 2101
Error: Can Not Connect. Enter the disable host name/IP address.
Send FTP Error 2101
Error: Can Not Connect. Assign the wrong port number.
Send FTP Error 2101
Error: Can Not Connect. Network is not connected.
Send FTP Error 2102
Error: Cannot Connect With Timeout. The server is unable to communicate.
Send FTP Error 2102
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send FTP Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.
Send FTP Error 2201
Error: Network Transfer. Error occurs on the network.
Send FTP Error 2202
Error: Network Transfer With Timeout. Error occurs on the network.
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
Send FTP Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send FTP Error 3101
Error: Server Response. The server is error status.
Send FTP Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send email Error 1101
Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send email Error 1102
Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send email Error 1104
Error: No Recipient Address. The destination address is not specified.
Send email Error 1105
Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send email Error 1106
Error: No Sender Info. Sender address is not entered.
Send email Error 2101
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send email Error 2101
Error: Can Not Connect. The specified server is not SMTP server.
Send email Error 2101
Error: Can Not Connect. Network is not connected.
Send email Error 2102
Error: Cannot Connect With Timeout. The server is unable to communicate.
Send email Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.
Send email Error 2201
Error: Network Transfer. Error occurs on the network.
Send email Error 2202
Error: Network Transfer With Timeout. Error occurs on the network.
Send email Error 2203
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
CS-2560, CS-3060
Needs User messages.
Send email Error 2204
Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send email Error 3101
Error: Server Response. The server is error status.
Send email Error 3101
Error: Server Response. Server setting is not authenticated normally.
Send email Error 3201
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send email Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
TWAIN Error 2202
Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
TWAIN Error 9181
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Software Error 5101
Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5102
Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5103
Error: Not Yet Opened. Error for storage status in the operation handle.
Software Error 5104
Error: Already Opened. Error for storage status in the operation handle.
Software Error 7101
Error: Memory Allocation. Insufficient memory space.
Software Error 7102
Error: Socket Create. Unable to create a communication socket.
Software Error 720f
Error: Unknown Error. Unable to determine the cause.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
935
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns disable C0060 error. For 2540/3040: 10871087; For 2560/3060: Status > 10871087
Start > MODE1 > Start > power Off/On. Set to MODE0 when problem is resolved. May be done up to (3) times.
Turn power Off/On. If code immediately returns initialize all data: 10871087
Start > Inch > Start > power Off/On.
Turn power Off/On. If code immediately returns initialize backup data for image processing. For 2540/3040: 10871087; For 2560/3060: Status > 10871087
Start > Main+Engine > Inch > Start > power Off/On. (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
24
933
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
Do not power Off/On. Format hard drive: Status > 10871087
Start > Execute > Start (tech only)
Power Off. Reseat BU-10 CF card. Power On. If code immediately returns initialize CF: Status > 10871087
Start > RECOVERY CF > Start > power Off/On >FAX IMAGE > Execute > Start > INITIALIZE CF > Start > power Off/On (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
906 Start > Execute > StartFor 2540/3040: 10871087; For 2560/3060: Status > 10871087
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
163 Start > Execute > Start
163 Start > Execute > Start
163 Start > Execute > Start
163 Start > Execute > Start
163 Start > Execute > Start
163 Start > Execute > Start
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
906 Start > Execute > Start
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
906 Start > Execute > Start
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
For 2540/3040: 10871087; For 2560/3060: Status > 10871087
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Service Checks
1) Repl fax card.
1) Repl main PWB.
1) Repl main PWB.
1) Repl main PWB.
1) Pinout harnass, 2) Repl drum unit.
1) Repl engine PWB, 2) Repl main PWB.
1) Reload firmware, 2) Install compatible fax card (Fax Sys M (B)).
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Run simulation U022, 2) Repl engine PWB.
1) Contact Kyocera Service Administrative Division, 2) Repl engine PWB, 3) Repl main PWB.
1) Replace engine PWB.
1) Reseat BU10 CF, 2) Run sim U933.
1) Reseat connectors on engine PWB & main PWB, 2) Repl engine PWB, 3) Repl main PWB.
1) Reseat interface PWB to printer PWB, 2) Reseat DIMMs or DDRs, 3) Repl printer PWB. 4) Repl engine PWB.
1) Reseat connectors @ fax & main PWB, 2) Repl fax card, 3) Repl main PWB.
1) Reseat YC22 @ engine PWB & connectors to PF-670 main PWB, 2) Repl PF-670 main PWB, 3) Repl engine PWB.
1) Reseat YC4 @ engine PWB & connectors on the finisher, 2) Repl. finisher main PWB, 3) Repl engine PWB.
1) Reseat YC5 @ engine PWB & connectors on the finisher, 2) Repl. finisher main PWB, 3) Repl engine PWB.
1) Repl DIMM on main PWB, 2) Repl main PWB.
1) Reseat DIMM on main PWB, 2) Repl main PWB.
1) Reseat YC8 @ Main PCB & connectors to HDD, 2) Reformat HDD, 3) Repl HDD, 4) Repl main PWB.
1) Repl main PWB.
1) Reinstall fax firmware, 2) Repl fax card.
1) Reinstall fax firmware, 2) Repl fax card.
1) Reinstall fax firmware, 2) Repl fax card.
1) Reinstall fax firmware, 2) Repl fax card.
1) Reinstall fax firmware, 2) Repl fax card.
1) Reseat the fax card, 2) Repl fax card.
1) Pinout harnass, 2) Repl developing unit.
1) Reseat the fax card, 2) Repl fax card, 3) Repl main PWB.
1) Reseat YC23 @ engine PWB & upper lift motor connector, 2) Check for drive problems. 3) Check for open motor coil. Repl lift motor, 4) Check YC23-B9 @ Engine PWB goes low when upper lift switch is OFF. If no, replace upper lift switch, 5) Repl engine PWB.
1) Reseat YC23 @ engine PWB & lower lift motor connector, 2) Check for lift drive problem 3) Check for open motor coil. Repl lift motor, 4) Check YC23-A2 @ Engine PWB goes low when lower lift switch is OFF. If no, replace lower lift switch, 5) Repl engine PWB.
1) Reseat YC22 @ engine PWB and PF main PWB, 2) Pinout harnass, 3) Check for lift drive problem 4) Check for open motor coil. Repl lift motor, 5) Check YC1-5 @ PF Main PWB goes low when lift switch 1 is OFF. If no, replace lift switch 1.
1) Reseat YC22 @ engine PWB and PF main PWB, 2) Pinout harnass, 3) Check for lift drive problem 4) Check for open motor coil. Repl lift motor, 5) Check YC1-7 @ PF Main PWB goes low when lift switch 2 is OFF. If no, replace lift switch 2.
1) Reseat YC10 @ engine PWB & main motor connector, 2) Pinout harnass, 3) Check for drive problems, 4) Repl engine PWB, 5) Repl main motor.
1) Reseat YC10 @ engine PWB & drum motor connector, 2) Pinout harnass, 3) Check for drive problems, 4) Repl drum motor, 5) Repl engine PWB.
1) Reseat YC10 @ engine PWB & paper feed motor connector, 2) Pinout harnass, 3) Check for drive problems, 4) Repl paper feed motor, 5) Repl engine PWB.
1) Reseat YC22 @ engine PWB and PF main PWB, 2) Pinout harnass, 3) Check for drive problems. 4) Repl drive motor, 5) Repl PF main PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC17 @ engine PWB & scanner HPS connector, 3) Repl home position switch, 4) Repl scanner motor, 5) Repl engine PWB.
1) Reseat YC16 @ engine PWB & inverter PWB connectors, 2) Repl lamp & inverter PWB, 3) Adj position of shading plate, 4) Repl scanner HPS, 5) Repl engine PWB.
1) Reseat YC4 @ main PWB & CCD PWB connectors, 2) Repl lamp & inverter PWB, 4) Repl main PWB, 5) Repl CCD PWB.
1) Reseat YC18 @ main PWB & CCD PWB connectors, 2) Repl lamp & inverter PWB, 4) Repl main PWB, 5) Repl CCD PWB.
1) Reseat YC18 @ main PWB & CCD PWB connectors, 2) Repl main PWB, 3) Repl CCD PWB.
1) Reseat YC2 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC2 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC2 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC2 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Check that thermistor1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters 4) Repl PSU, 5) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 2, 3) Repl engine PWB.
1) Check fixing heaters 2) Check that thermistor2 is contacting heat roller & clean, 3) Check thermal switch, 4) Repl PSU, 5) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1, 3) Repl engine PWB.
1) Check that thermistor1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters 4) Repl PSU, 5) Repl engine PWB.
1) Check wall outlet ground to neutral voltage. 2) Repl PSU, 3) Repl ngine PWB.
1) Reinsert drum unit, 2) Repl drum unit.
1) Reseat YC1 @ engine PWB, 2) Reinsert fuser unit.
1) Reseat YC1 @ engine PWB & toner feed motor connector, 2) Check for drive problems, 3) Run sim U135 to test toner motor. If fails repl toner motor, 4) Repl engine PWB.
1) Reseat YC32 @ engine PWB, 2) Repl temperature sensor.
1) Reseat YC1 @ engine PWB, 2) Replace developing unit.
1) Reinsert developing unit, 2) Repl developing unit.
1) Reseat YC1 @ engine PWB, 2) Repl the humidity sensor.
1) Reseat connectors, 2) Pinout harnass, 3) Repl upper limit sensor, paper push sensor, or surface view sensor, 4) Repl finisher main PWB.
1) Reseat connectors or replace tray lower limit sensor, push paper sensor, surface view sensor, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat connectors or replace tray lower limit sensor, push paper sensor, surface view sensor, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat front side registration HPS, 2) Reseat front side registration motor connector, 3) Repl front side registration HPS, 4) Replace front side registration motor, 5) Repl finisher main PWB.
1) Repl finisher main PWB.
1) Reseat sensor connectors, 2) Reseat motor connectors, 3) Pinout harnass, 4) Repl adjustment home position sensor. 5) Repl adjustment motor, 4) Replace finisher main PWB.
1) Reseat rear side registration HPS, 2) Reseat rear side registration motor connector, 3) Repl rear side registration HPS, 4) Replace rear side registration motor, 5) Repl finisher main PWB.
1) Reseat trailing edge registration HPS, 2) Reseat trailing edge registration motor connector, 3) Repl trailing edge registration HPS, 4) Replace trailing edge registration motor, 5) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl front stapler assy, 4) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl stapler assy, 4) Repl finisher main PWB.
1) Reseat paper entry sensor connector, 2) Clean foreign matter from paper entry sensor, 3) Repl paper entry sensor, 4) Repl finisher main PWB.
1) Reseat YC24 & YC31 @ engine PWB & the pigtail to the copier, 2) Repl DP main PWB.
1) Repl DP main PWB, 2) Contact Service Administration Division.
1) Run simulation U989 HDD Scandisk.
1) Repl main EEPROM then flash.
1) Repl main PWB.
1) Bug in firmware v. 3.001 & 03/08A. Upgrade to most current firmware (currently 2.42A 02-02-10), 2) Check print driver/emulation. May occur using PCL5e. Select PCL XL.
1) Occurred after relocating machine. Flash machine.
1) Flash machine, 2) Replace expanded memory.
1) Repl main PWB, 2) Repl operation panel PWB.
1) Repl expansion memory, 2) Repl main PWB.
1) Repl main PWB.
1) Replace engine PWB, 2) Repl main PWB.
1) Repl main PWB.
1) Repl engine PWB.
1) Repl engine PWB.
1) Repl flash ROM, 2) Repl engine PWB.
1) Repl flash ROM, 2) Repl engine PWB.
1) Repl main PWB.
1) Repl power source PWB.
Load paper.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check is the server is operating properly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Scan folder is not shared out to the network properly.
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Set the number of pages to 999 or less.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Specify the destination address.
Select valid POP3 user other than [Other].
Check if the server is operating properly.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Check the network connection (cable, network condition within LAN, etc.).
Model Error Code DescriptionC0030
C0070
C0100
C0110
C0130
C0150
C0160
C0170
C0210
C0240
C0250
C0280
CS-3035 (2FD), CS-4035 (2FF), CS-5035
(2FG)
Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.
CS-3035, CS-4035, CS-5035
Fax PWB Incompatability Detection Problem. Fax software is not compatible with MMI software.
CS-3035, CS-4035, CS-5035
Operation Unit PWB Backup Memory Read/Write Error. Reading from or writing to the backup memory cannot be performed.
CS-3035, CS-4035, CS-5035
Operation Unit PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS-3035, CS-4035, CS-5035
Fax Control PWB Software Switch Checksum Error. A checksum error occurred with the software switch value stored in thr flsh ROM of the fax control PWB.
CS-3035, CS-4035, CS-5035
Main PWB EEPROM Backup Memory Read/Write Error 2. EEPROM backup memory cannot be written or read.
CS-3035, CS-4035, CS-5035
Main PWB EEPROM Backup Memory Data Problem. A checksum error in backup data is detected.
CS-3035, CS-4035, CS-5035
Accounting Count Error. A checksum error in backup data of the accounting counter is detected.
CS-3035, CS-4035, CS-5035
MMI Communication Problem. There is no reply after 20 retries at communication.
CS-3035, CS-4035, CS-5035
Printer Board Communication Problem. There is no reply after 20 retries at communication.
CS-3035, CS-4035, CS-5035
Scanner Network Board Communication Problem. There is no reply after 20 retries at communication.
CS-3035, CS-4035, CS-5035
Communication Problem With Fax Control PWB And Main PWB. There is no reply after 20 retries at communication.
C0320
C0420
C0440
C0450
C0470
C0610
CS-3035, CS-4035, CS-5035
Energy Save Communication Problem. Communication errors from the communication microcomputer on the main PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
CS-3035, CS-4035, CS-5035
PF-70/PF-75 Communication Problem. Communication errors from the communication microcomputer on the main PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
CS-3035, CS-4035, CS-5035
DF-71/DF-73/DF-75 Finisher Communication Problem. Communication errors from the communication microcomputer on the main PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
CS-3035, CS-4035, CS-5035
M-2107 Mailbox Communication Problem. Communication errors from the communication microcomputer on the main PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
CS-3035, CS-4035, CS-5035
Switchback Unit Communication Problem. Communication errors from the communication microcomputer on the main PWB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.
CS-3035, CS-4035, CS-5035
Bitmap Problem. There is a problem with the data or address bus of the bitmap DRAM. The DIMM on the memory PWB does not operate correctly.
C0630
C0640 Hard Disk Drive cannot be accessed.
C0820
C0830
C0860
C0870
C0880
C0890
C0900
CS-3035, CS-4035, CS-5035
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
Fax Control PWB CG ROM Checksum Error. A checksum error occurred with the CG ROM data of the fax control PWB.
CS-3035, CS-4035, CS-5035
Fax Control PWB Flash Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
CS-3035, CS-4035, CS-5035
Fax Control PWB Software Switch Checksum Error. A checksum error occurred with the software switch value of the fax control PWB.
CS-3035, CS-4035, CS-5035
Graphics Data Transfer Problem. High capacity data transfer between the fax control PWB and the main PWB was not normally performed even if the data transfer was retried the specified times.
CS-3035, CS-4035, CS-5035
Fax PWB program archive problem. When power is turned On, the compressed program in the flash ROM on the fax control PWB was not successfully decompressed.
CS-3035, CS-4035, CS-5035
Fax PWB CG Font archive problem. When power is turned On, the compressed CG font in the flash ROM on the fax control PWB was not successfully decompressed.
CS-3035, CS-4035, CS-5035
Fax PWB Incompatability Detection Problem. Fax software is not compatible with MMI software.
C1010
C1020
C1030
CS-3035, CS-4035, CS-5035
Cassette #1 Lift Motor error. At drawer insertion, upper lift limit switch (ULLS) does not turn On within 6 sec of upper lift motor (ULM) turning On, and the ULLS does not turn On in a retry operation after turning Off the ULM for 200ms. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of the drawer the ULLS still does not turn On. This problem occurrs 4 times consecutively. During copying the ULLS does not turn On within 200ms of the ULM turning On. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of drawer the ULLS still does not turn On. This problem occurrs 4 times consecutively.
CS-3035, CS-4035, CS-5035
Cassette #2 Lift Motor error. At drawer insertion, lower lift limit switch (LLLS) does not turn On within 6 sec of lower lift motor (LLM) turning On, and the LLLS does not turn On in a retry operation after turning Off the LLM for 200ms. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of the drawer the LLLS still does not turn On. This problem occurrs 4 times consecutively. During copying the LLLS does not turn On within 200ms of the LLM turning On. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of drawer the LLLS still does not turn On. This problem occurrs 4 times consecutively.
CS-3035, CS-4035, CS-5035
PF-70 optional cassette #3 lift motor error. At drawer insertion, desk upper lift limit switch (DULLS) does not turn On within 10 sec of desk upper lift motor (DULM) turning On. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of the drawer the DULLS still does not turn On. This problem occurrs 4 times consecutively.
C1040
C1100
C1110
C1120
C1130
C2000
C2500
C2600
C2600
CS-3035, CS-4035, CS-5035
PF-70 optional cassette #4 lift motor error. At drawer insertion, desk lower lift limit switch (DLLLS) does not turn On within 10 sec of desk lower lift motor (DLLM) turning On. (Prompt: "Remove and reinstall drawer.") After removal and reinstallation of the drawer the DLLLS still does not turn On. This problem occurrs 4 times consecutively.
CS-3035, CS-4035, CS-5035
PF-75 (Left) Paper Deck Motor 1 error. Exceeds 1 second overcurrent.
CS-3035, CS-4035, CS-5035
PF-75 (Right) Paper Deck Motor 2 error. Exceeds 1 second overcurrent.
CS-3035, CS-4035, CS-5035
PF-75 (Right) Lift Motor 1 position problem. Deck level switch 2 remains off after 30 seconds of paper deck motor 2 operation.
CS-3035, CS-4035, CS-5035
PF-75 (Left) Lift Motor 2 position problem. Deck level switch 1 remains off after 30 seconds of paper deck motor 1 operation.
CS-3035, CS-4035, CS-5035
Drive Motor Problem. LOCK ALM signal remains high for 1 sec, 1 sec after the drive motor has turned On.
CS-3035, CS-4035, CS-5035
Paper Feed Motor error. LOCK ALM signal remains high for 1 sec, 1 sec after the paper feed motor has turned On.
CS-3035, CS-4035, CS-5035
PF-70 Drive Motor error. No pulse is input within 500ms of startup. No pulse is input within 100ms of the previous pulse input.
CS-3035, CS-4035, CS-5035
PF-75 Paper Conveying Motor error. No pulse is input within 500ms of startup. No pulse is input within 100ms of the previous pulse input.
C3100
C3200
C3300
C4000
C4010
C4200
C5300
C6000
CS-3035, CS-4035, CS-5035
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
CS-3035, CS-4035, CS-5035
Exposure Lamp Problem. Non-lighting of the exposure lamp is detected at the beginning of copying.
CS-3035, CS-4035, CS-5035
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
CS-3035, CS-4035, CS-5035
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
CS-3035, CS-4035, CS-5035
Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.
CS-3035, CS-4035, CS-5035
BD Steady-State Problem. VTC detects a Beam Detect error for 600ms after polygon motor stabilization.
CS-3035, CS-4035, CS-5035
Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously.
CS-3035, CS-4035, CS-5035
Broken Fixing Heater Wire. At power On or start of fixing control from sleep mode, the detected temperature at thermistor 2 is below 40C/104F, 10 sec after fixing heater M is turner On. At power On or start of fixing control from sleep mode, the detected temperature at thermistor 21 is below 40C/104F, 7 sec after fixing heater S is turner On. During standby, the detected temperatures of thermistor 1 and 2 become lower than 60C/140F.
C6020
C6050
C6400
C6410
C6420
C7300
C7400
C7410
C7450
C7800
C7810
C8010
CS-3035, CS-4035, CS-5035
Abnormally High Thermistor Temperature. Thermistor 1 detectes 250C/482F. Thermistor 2 detects 210C/410F.
CS-3035, CS-4035, CS-5035
Abnormally Low Thermistor Temperature. Thermistor 2 detects 80C/176F or lower when heater M is On, during copying. Thermistor 1 detects 100C/212F or lower when heater M & S is On, during copying.
CS-3035, CS-4035, CS-5035
Zero-Cross Signal Error. Main PWB does not detect the zero-cross signal (Z CROSS SIG) for 5 sec at power On, and for 5 sec any other time.
CS-3035, CS-4035, CS-5035
Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.
CS-3035, CS-4035, CS-5035
Fuser Unit Fuse Cut Problem. The fixing temperature remains at 0C/32F for 30 sec continuously when the fixing heater is On.
CS-3035, CS-4035, CS-5035
Toner Sensor Problem. While the toner container sensor is On, the toner sensor in the developing unit does not turn On after the toner sensor turns Off and toner is replenished from the toner container.
CS-3035, CS-4035, CS-5035
Image Formation Unit Connector Insertion Problem. Absence of the image formation unit is detected.
CS-3035, CS-4035, CS-5035
Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
CS-3035, CS-4035, CS-5035
Image Formation Unit Fuse Cut Problem. The input voltage is above 4.5v.
CS-3035, CS-4035, CS-5035
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
CS-3035, CS-4035, CS-5035
Short-Circuited External Thermistor. Thermistor input value is 1.0v or less.
CS-3035, CS-4035, CS-5035
DF-71 Paper Conveying Motor Problem. Paper conveying motor lock signal is detected for 500ms or more during activation.
C8030
C8140
C8170
C8180
C8190
CS-3035, CS-4035, CS-5035
DF-71 Paper Conveying Belt Problem. An On-to-Off or Off-to-On state change of the paper conveying belt home position sensor is not detected within 2 sec of the paper conveying belt clutch turning on.
CS-3035, CS-4035, CS-5035
DF-71 Finisher Tray Elevation Motor Problem. The sort tray is not detected in the home position within 30 sec of the start of the tray elevation motor rotation.
CS-3035, CS-4035, CS-5035
DF-71 or DF-78 Front Side Registration Motor Problem. If the front side registration home position sensor is On at initialization, the sensor does not turn Off within 570ms of starting initialization. If the front side registration home position sensor is Off at initialization, the sensor does not turn On within 3180ms of starting initialization.
CS-3035, CS-4035, CS-5035
DF-71 or DF-78 Rear Side Registration Motor Problem. If the rear side registration home position sensor is On at initialization, the sensor does not turn Off within 570ms of starting initialization. If the rear side registration home position sensor is Off at initialization, the sensor does not turn On within 2880ms of starting initialization.
CS-3035, CS-4035, CS-5035
DF-78 Trailing Edge Registration Motor Problem. If the trail edge registration home position sensor is On at initialization, the sensor does not turn Off within 570ms of starting initialization. If the trail edge registration home position sensor is Off at initialization, the sensor does not turn On within 4550ms of starting initialization.
C8210
C8220
C8300
C8310
C8320
C8330
C8340
C8350
C8360
C8370
C8380 DF-75 Booklet Stitcher Folding Problem.
C8390
C8410 DF-75 Punch Motor Problem.
C8420
C8430
C8440
CS-3035, CS-4035, CS-5035
DF-71, DF-73, DF-75, DF-78 Front Stapler Moving Motor Error. Front stapler home position sensor does not change state from non-detection to detection within 200ms of the start of front stapler motor counterclockwise (forward) rotation. During initialization, the front stapler home position sensor does not change state from non-detection to detection within 600ms of the start of front stapler motor clockwise (reverse) rotation.
CS-3035, CS-4035, CS-5035
DF-71 Rear Stapler Moving Motor Error. Rear stapler home position sensor does not change state from non-detection to detection within 200ms of the start of rear stapler motor counterclockwise (forward) rotation. During initialization, the rear stapler home position sensor does not change state from non-detection to detection within 600ms of the start of rear stapler motor clockwise (reverse) rotation.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Paper Ejection Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Elevation Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Rear Jog Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Front Jog Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Staple Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Batch Processing Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Stapler Shift Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Paddle Motor Problem.
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Backup RAM Data Problem.
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Shift Motor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Punch Communication Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Punch Sensor Problem.
C8450
C8460
C8470
C8480
C8500
E001
E010
E011
E012
E020
E021
E022
E023
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Side Punch Sensor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Punch Backup RAM Data Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Punch Dust Sensor Problem.
CS-3035, CS-4035, CS-5035
DF-75 Booklet Stitcher Broken Punch Power Source Wire Problem.
CS-3035, CS-4035, CS-5035
M-2107 Mailbox Drive Motor Problem. While the mailbox drive motor is driving, Synchronization signals do not synchronize continuously for 464ms (motor lockup).
CS-3035, CS-4035, CS-5035
Transmission in progress was cancelled by operator.
CS-3035, CS-4035, CS-5035
Destination computer could not be found during data transmission. (An error occurred that could not be classified more clearly under any error code after E011.) The scanner could not find the computer that was running the personal Address Book.
CS-3035, CS-4035, CS-5035
Transmission was stopped due to problems with the image data itself.
CS-3035, CS-4035, CS-5035
The scanner attempted to transmit image data, but was unable to access the corresponding information in the personal Address Book due to a connection problem.
CS-3035, CS-4035, CS-5035
An attempt to use the Send E-mail function was made, but the scanner was unable to find the SMTP server.
CS-3035, CS-4035, CS-5035
The destination of the email is listed under the restricted domain names, or is not listed under the permitted domain names.
CS-3035, CS-4035, CS-5035
The mail contained an email address that the SMTP server could not find.
CS-3035, CS-4035, CS-5035
The SMTP server is not operating properly.
E024 SMTP Authentication error.
E030
E031
E032
E033
E034
E035
E036
E039
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
The destination computer cannot be found. Either the Scan File Utility is not running or it is already communicating with another scanner.
CS-3035, CS-4035, CS-5035
The scanner attempted to transmit image data, but the registered password did not match the password in the destination computer.
CS-3035, CS-4035, CS-5035
During the scan-to-PC operation, the hard drive on the destination computer ran out of available space.
CS-3035, CS-4035, CS-5035
The versions of the Scan File Utility do not match.
CS-3035, CS-4035, CS-5035
Transmission was not possible because the Scan File Utility is communicating with another scanner. Send failed.
CS-3035, CS-4035, CS-5035
During group transmission, the number of the save folder registered in the Scan File Utility did not match.
CS-3035, CS-4035, CS-5035
During compression of the scanned image data, the data size went over the maximum limit.
CS-3035, CS-4035, CS-5035
The response received from the destination computer under the Scan-to-PC function was not an appropriate one. Unexpected trouble has occurred in the destination computer.
E059
E061
E080 The FTP server cannot be found.
E081 The FTP server is failed to login.
E082 The storing path is incorrect.
E083 The error occurred in the FTP server.
E101
E00000 or U00000
E00100 or U00100
E00200 or U00200
E00300 or U00300
CS-3035, CS-4035, CS-5035
A command received from the transmitting computer was not an appropriate one. Trouble has occurred in the computer that is running the corresponding personal Address Book.
CS-3035, CS-4035, CS-5035
When selecting the group in the destination computer under either the Send E-mail or Scan to PC functions, some type of trouble has occurred in the information for the registered members of the group.
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
An error has occurred while selecting multiple destinations.
CS-3035, CS-4035, CS-5035
Fax Communication Error: No response or line busy after the set number of redials.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420
E00421 or U00421
E00430 or U00430
E00430 or U00430
E00431 or U00431
E00431 or U00431
E00432 or U00432
E00432 or U00432
E00433 or U00433
E00433 or U00433
CS-3035, CS-4035, CS-5035
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based relay reception was interrupted because of a mismatch in the specified F-code relay box number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A F-code based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A F-code based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based bulletin board transmission request was received but data was not present in the F-code confidential box.
E00434 or U00434
E00435 or U00435
E00435 or U00435
E00440 or U00440
E00440 or U00440
E00440 or U00440
E00441 or U00441
E00450 or U00450
E00460 or U00460
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based bulletin board transmission request was received but interrupted because the specific F-code confidential box was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based confidential reception or F-code based relay reception was interrupted because the specific F-code box was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based confidential reception or F-code based relay command reception was interrupted because the specific F-code box number was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
CS-3035, CS-4035, CS-5035
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460
E00462 or U00462
E00500 or U00500
E00600 or U00600
E00601 or U00601
E00602 or U00602
E00603 or U00603
E00604 or U00604
E00610 or U00610
E00611 or U00611
E00613 or U00613
E00614 or U00614
E00615 or U00615
E00620 or U00620
E00622 or U00622
E00655 or U00655
E00656 or U00656
E00670 or U00670
CS-3035, CS-4035, CS-5035
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
CS-3035, CS-4035, CS-5035
Fax Communication Error: The document processor cover is open.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Document jam or the document length exceeds the maximum.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Image scanning section problem
CS-3035, CS-4035, CS-5035
Fax Communication Error: No document feed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Recording section cover open.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Recording paper jam.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Image writing section problem.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Nearly empty of recording paper.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Empty of recording paper.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Copier fixing unit problem.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Copier drive motor problem.
CS-3035, CS-4035, CS-5035
Fax Communication Error: CTS was not activated after RTS due to a modem error.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Power was cut off during communication.
E00677 or U00677
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700
E00800 or U00800
E00810 or U00810
E00900 or U00900
E00910 or U00910
E01000 or U01000
E01000 or U01000
E01001 or U01001
E01010 or U01010
CS-3035, CS-4035, CS-5035
Fax Communication Error: There was no file to transmit in the memory transmission mode.
CS-3035, CS-4035, CS-5035
CS-3035, CS-4035, CS-5035
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011
E01012 or U01012
E01013 or U01013
E01014 or U01014
E01015 or U01015
E01016 or U01016
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017
E01018 or U01018
E01019 or U01019
E01020 or U01020
E01021 or U01021
E01022 or U01022
E01023 or U01023
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PSS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024
E01025 or U01025
E01026 or U01026
E01027 or U01027
E01028 or U01028
E01040 or U01040
E01041 or U01041
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PSS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042
E01043 or U01043
E01044 or U01044
E01045 or U01045
E01046 or U01046
E01047 or U01047
E01048 or U01048
E01049 or U01049
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050
E01051 or U01051
E01052 or U01052
E01053 or U01053
E01054 or U01054
E01055 or U01055
E01056 or U01056
E01057 or U01057
E01070 or U01070
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071
E01072 or U01072
E01073 or U01073
E01080 or U01080
E01091 or U01091
E01092 or U01092
E01100 or U01100
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
E01102 or U01102
E01110 or U01110
E01111 or U01111
E01112 or U01112
E01113 or U01113
E01114 or U01114
E01115 or U01115
E01116 or U01116
E01117 or U01117
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
E01119 or U01119
E01120 or U01120
E01121 or U01121
E01122 or U01122
E01123 or U01123
E01124 or U01124
E01125 or U01125
E01126 or U01126
E01127 or U01127
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128
E01129 or U01129
E01140 or U01140
E01141 or U01141
E01142 or U01142
E01143 or U01143
E01144 or U01144
E01145 or U01145
E01146 or U01146
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147
E01148 or U01148
E01149 or U01149
E01150 or U01150
E01151 or U01151
E01152 or U01152
E01153 or U01153
E01154 or U01154
E01155 or U01155
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIP signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RNR signal (ECM).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160
E01161 or U01161
E01162 or U01162
E01163 or U01163
E01164 or U01164
E01170 or U01170
E01172 or U01172
E01191 or U01191
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199
E01400 or U01400
E01500 or U01500
E01600 or U01600
E01700 or U01700
E01720 or U01720
E01721 or U01721
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
CS-3035, CS-4035, CS-5035
Fax Communication Error: An invalid one-touch key was specified during communication.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred when called in V.8 mode.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800
E01810 or U01810
E01820 or U01820
E01821 or U01821
E02000 or U02000
E02100 or U02100
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units (including when an impossible combination of communication speed and symbol speed occurs). After MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
CS-3035, CS-4035, CS-5035
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200
E02200 or U02200
E02200 or U02200
E02303 or U02303
E02304 or U02304
E02400 or U02400
E03000 or U03000
E03100 or U03100
E03200 or U03200
E03200 or U03200
CS-3035, CS-4035, CS-5035
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based relay broadcast transmission failed because the data registered in the F-code relay box was deleted.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
CS-3035, CS-4035, CS-5035
Fax Communication Error: An interoffice F-code based relay transmission was interrupted because of a mismatch in the specified relay box number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: No document was present in the destination unit when polling reception started.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In interoffice F-code based bulletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300
E03300 or U03300
E03400 or U03400
E03500 or U03500
E03500 or U03500
E03500 or U03500
E03600 or U03600
E03600 or U03600
E03700 or U03700
E03700 or U03700
CS-3035, CS-4035, CS-5035
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In interoffice F-code based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In interoffice F-code based bulletin board reception, the specified F-code confidential box number was not registered in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: The destination was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS-3035, CS-4035, CS-5035
Fax Communication Error: An interoffice F-code based bulletin board reception was interrupted because of a mismatch in the specified F-code confidential box number.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Interoffice F-code based bulletin board reception failed because the destination unit had no F-code based bulletin board transmission capability, or data was not stored in any F-code confidental box in the destination unit.
E04000 or U04000
E04000 or U04000
E04000 or U04000
E04100 or U04100
E04100 or U04100
E04200 or U04200
E04300 or U04300
E04400 or U04400
E04401 or U04401
E04500 or U04500
E05000 or U05000
CS-3035, CS-4035, CS-5035
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In interoffice F-code based transmission mode, the specified F-code box number was not registered in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: The destination was being accessed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
CS-3035, CS-4035, CS-5035
Fax Communication Error: F-code based transmission failed because the destination unit had no F-code based reception capability.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100
E05200 or U05200
E05300 or U05300
E09000 or U09000
E12000 or U12000
E12000 or U12000
E12100 or U12100
E14000 or U14000
E14000 or U14000
E14100 or U14100
E14100 or U14100
E19000 or U19000
E19100 or U19100
E19200 or U19200
CS-3035, CS-4035, CS-5035
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Password check reception was interrupted because the permit ID numbers did not match.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Password check reception was interrupted because the permitted numbers did not match.
CS-3035, CS-4035, CS-5035
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: In F-code based relay reception memory overflowed.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed during confidential reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed in F-code based confidential reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed in the destination unit during interoffice F-code based transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed during memory reception.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory overflowed in the destination unit during transmission.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
E19400 or U19400
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1103
Send SMB Error 1103
Send SMB Error 1103
Send SMB Error 1105
Send SMB Error 2101
Send SMB Error 2101
Send SMB Error 2101
Send SMB Error 2103
Send SMB Error 2201
CS-3035, CS-4035, CS-5035
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
CS-3035, CS-4035, CS-5035
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Host name error.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. SMB protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Assign the wrong port number.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
Send SMB Error 2203
Send SMB Error 9181
Send FTP Error 1101
Send FTP Error 1102
Send FTP Error 1102
Send FTP Error 1103
Send FTP Error 1103
Send FTP Error 1105
Send FTP Error 2101
Send FTP Error 2101
Send FTP Error 2101
Send FTP Error 2102
Send FTP Error 2102
Send FTP Error 2103
Send FTP Error 2201
Send FTP Error 2202
Send FTP Error 2203
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Host Name. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Username/Password. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Username/Password. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. FTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Assign the wrong port number.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send FTP Error 3101
Send FTP Error 9181
Send email Error 1101
Send email Error 1102
Send email Error 1104
Send email Error 1105
Send email Error 1106
Send email Error 2101
Send email Error 2101
Send email Error 2101
Send email Error 2102
Send email Error 2103
Send email Error 2201
Send email Error 2202
Send email Error 2203
Send email Error 2204
CS-3050, CS-4050, CS-5050
Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Host Name. SMTP server name is not set. Error SMTP server name.
CS-3050, CS-4050, CS-5050
Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
CS-3050, CS-4050, CS-5050
Error: No Recipient Address. The destination address is not specified.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. SMTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: No Sender Info. Sender address is not entered.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. The specified server is not SMTP server.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send email Error 3101
Send email Error 3101
Send email Error 3201
Send email Error 9181
TWAIN Error 2202
TWAIN Error 9181
Software Error 5101
Software Error 5102
Software Error 5103
Software Error 5104
Software Error 7101
Software Error 7102
Software Error 720f
CS-3050, CS-4050, CS-5050
Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Error: Server Response. Server setting is not authenticated normally.
CS-3050, CS-4050, CS-5050
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Not Yet Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Already Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Memory Allocation. Insufficient memory space.
CS-3050, CS-4050, CS-5050
Error: Socket Create. Unable to create a communication socket.
CS-3050, CS-4050, CS-5050
Error: Unknown Error. Unable to determine the cause.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1101
Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1101
Send FTP Error: Host Name. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1104
Send Email Error: No Recipient Address. The destination address is not specified.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1106
Send Email Error: No Sender Info. Sender address is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. The specified server is not SMTP server.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2102
Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2102
Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2103
Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2201
Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2202
Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2202
Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2203
Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Is the acceptable staple count exceeded?
"Add paper in cassette #." Is the indicated cassette out of paper?
"Add paper in MP tray."
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2204
Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3101
Send Email/FTP Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3101
Send Email Error: Server Response. Server setting is not authenticated normally.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3201
Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5101
Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5102
Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5103
Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5104
Send Software Error: Already Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
7102
Send Software Error: Socket Create. Unable to create a communication socket.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
720f
Send Software Error: Unknown Error. Unable to determine the cause.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
"Acceptable staple count exceeded."
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Is the paper of the specified size loaded in the multipurpose tray?
"Add staples."
"Add toner."
"An error has occurred."
"Box Limit Exceeded."
"Cannot execute this job." Job is restricted by Job Accounting.
"Cannot offset this paper."
"Cannot staple this paper."
"Check the cover."
"Check the finisher." Is the document finisher set correctly?"
"Clean the slit glass." Dirt has been identified on the slit glass.
CS-3050, CS-4050, CS-5050
Has the document finisher run out of staples?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
An internal error has occurred.Make a note of the error code number displayed on the panel. See above.
CS-3050, CS-4050, CS-5050
Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
CS-3050, CS-4050, CS-5050
"Cannot connect to Authentication Server."
CS-3050, CS-4050, CS-5050
"Cannot duplex print on this paper."
Did you select a paper size/type that cannot be duplex printed?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
CS-3050, CS-4050, CS-5050
"Cannot punch this paper type."
Did you select a paper size/type that cannot be punched?
CS-3050, CS-4050, CS-5050
Did you select a paper size/type that cannot be stapled?
CS-3035, CS-4035, CS-5035
"Check domain name and host name.
The scanners domain name and host name have not been registered properly.
CS-3050, CS-4050, CS-5050
Are any covers open? Does the message indicate which cover is open?
CS-3050, CS-4050, CS-5050
"Check the document processor."
Is the document processor open? Is the top cover of the document processor open?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
There is a networking problem.
The ScanFile Utility is not running.
The email size exceeds the data capacity.
"Fax box limit exceeded."
CS-3035, CS-4035, CS-5035
"Communication error." when scanning.
CS-3035, CS-4035, CS-5035
"Communication time out has occurred." on PC.
A network cable was disconnected while data was transmitted.
CS-3035, CS-4035, CS-5035
"Destination address is not being registered."
The entered number has not been registered.
CS-3035, CS-4035, CS-5035
"Destination PC's application is out of order."
when scanning.
CS-3035, CS-4035, CS-5035
"Destination PC's is in use. Try again later." when
scanning.
The destination computer and the scanner are currently communicating.
CS-3035, CS-4035, CS-5035
"Destination PC's system error."
There is a problem with the destination PC.
CS-3035, CS-4035, CS-5035
"Destination PC's version is different. Contact
administrator."
The versions of the Addressbook do not match.
CS-3035, CS-4035, CS-5035
"E-mail size exceeds data capacity."
CS-3050, CS-4050, CS-5050
"Empty the punch waste box."
The punch waste box of the 3,000 sheet finisher is full.
CS-3050, CS-4050, CS-5050
"Failed to specify Job Accounting."
Job accounting is not specified in the print driver.
CS-3050, CS-4050, CS-5050
"Failed to store job retention data."
CS-3050, CS-4050, CS-5050
Fax box is full, and no further storage is available.
CS-3035, CS-4035, CS-5035
"Fax connection has been cut." on PC.
Transmission failed because data amount (traffic) on the network was too large.
An error has occurred on the hard disk.
"KPDL error." A PostScript error has occurred.
"Memory card error."
Memory Card Error: Format error.
"Memory is full."
CS-3035, CS-4035, CS-5035
"Fax connection could not be made for the following possible reasons: * The
FAX main unit isn't turned On. * Network FAX
address is wrong. * A fault has occurred at the fax machine." when faxing
from PC.
1) The fax system is not installed. 2) C0280 has occurred. 3) Fax software is not compatible with the NW-FAX functions. 4) Main PWB is not compatible with the NW-FAX functions. 5) NIC is being initialized. 6) Diagnostic code of NIC has occurred. 7) Network cable is disconnected. 8) Main switch is Off. 9) IP address or hostname is not correct.
CS-3035, CS-4035, CS-5035
"FAX memory is full." on PC.
Fax memory became full while transmission was performed.
CS-3050, CS-4050, CS-5050
"Folding tray is full of paper."
Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?"
CS-3050, CS-4050, CS-5050
"Hard Disk error. Job is cancelled. Press [End] ##"
CS-3050, CS-4050, CS-5050
"Incorrect Login User Name or Password."
CS-3050, CS-4050, CS-5050
"Job Accounting restriction exceeded."
The print count exceeded the acceptable count restricted by Job Accounting.
CS-3050, CS-4050, CS-5050
"Job Separator is full of paper."
Is the maximum capacity of the job separator tray exceeded?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
"Mailbox tray is full of paper."
CS-3050, CS-4050, CS-5050
Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted?
CS-3050, CS-4050, CS-5050
"Memory card error. Job is cancelled. Press [End].
Code: 01
CS-3050, CS-4050, CS-5050
"Memory card error. Job is cancelled. Press [End].
Code: 04
Memory Card Error: Insufficient memory card space to complete this operation.
CS-3050, CS-4050, CS-5050
Unable to continue the job, as the memory is used up."
"Memory Is Low" Logic Lockup
The selected destination is not registered.
"Paper Jam. ###"
"Print overrun." Warning. Low printer memory.
"Registration Full." The registration is full.
The waste toner box is full.
"Scanner memory is full."
"Scanner Paused"
CS-3050, CS-4050, CS-5050
CS-3035, CS-4035, CS-5035
"Network error has occurred." on PC.
A connection error of scanner NIC occurred while data was transmitted.
CS-3035, CS-4035, CS-5035
"Network scanner interface error."
A system error has occurred on the scanner.
CS-3035, CS-4035, CS-5035
"No destination address being registered."
CS-3050, CS-4050, CS-5050
Make a note of the jam location number displayed on the panel. Leave the machine On.
CS-3035, CS-4035, CS-5035
"PC of personal address list is in use. Try again
later."
The destination Addressbook and the scanner are currently communicating.
CS-3050, CS-4050, CS-5050
CS-3035, CS-4035, CS-5035
CS-3050, CS-4050, CS-5050
"Removable memory error."
An error has occurred on the USB stick memory or Compact Flash memory.
CS-3050, CS-4050, CS-5050
"Removable memory was removed."
CS-3050, CS-4050, CS-5050
"Replace all originals and press [Continue]."
CS-3050, CS-4050, CS-5050
"Replace the waste toner box."
CS-3050, CS-4050, CS-5050
"Reset all originals in the document processor."
Are there any originals left in the document processor?
CS-3050, CS-4050, CS-5050
Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
CS-3050, CS-4050, CS-5050
DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-3035, CS-4035, CS-5035
"Sender (user) is not registered. Contact
administrator."
User number 001 is not registered in the "Select sender name" list on this scanner.
"Set the folding tray."
"Set the folding unit."
"Set the waste toner box."
"Staple error."
"Staple jam."
"The ID is not registered." The account ID# does not match.
CS-3050, CS-4050, CS-5050
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
CS-3050, CS-4050, CS-5050
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
CS-3050, CS-4050, CS-5050
"Set the punch waste box."
The waste toner box is not installed correctly.
CS-3050, CS-4050, CS-5050
The waste toner box is not installed correctly.
CS-3035, CS-4035, CS-5035
"SMTP Authenticaion error. Contact administrator."
The MFP cannot login to the SMTP server.
CS-3050, CS-4050, CS-5050
The location of the jam will be indicated on the panel. Leave the machine On.
CS-3050, CS-4050, CS-5050
The location of the jam will be indicated on the panel. Leave the machine On.
CS-3035, CS-4035, CS-5035
"The FAX cannot be used" on PC.
1) The main switch is Off and memory reception is set. 2) Fax is being reset.
CS-3035, CS-4035, CS-5035
"The FAX is in use" on PC.
The following functions are current in use: copying, fax printing, fax setting, fax relay, remote diagnosis, printing interrupt occurs during transmission, network scanner in use, maintenance mode in use.
CS-3035, CS-4035, CS-5035
"The file was not saved. Check the destination
PC."
The hard disk capacity is exceeded or the same file name has been sent from more than one scanner at a time.
CS-3035, CS-4035, CS-5035
"The number of FAX transmission reservations has reached maximum."
on PC.
NW-FAX transmission was tried when 50 items of fax transmission was reserved.
CS-3050, CS-4050, CS-5050
CS-3035, CS-4035, CS-5035
"The job has been interrupted at the FAX
operation panel." on PC.
The interrupt key was pressed while transmission was performed.
The specified file is not found.
This name is already in use.
This number is already in use.
"Tray # is full of paper."
There is a problem at your computer.
"Unable to use scanner." Network is not connected.
CS-3050, CS-4050, CS-5050
"The memory card is not formatted."
Is the removable memory formatted by this machine?
CS-3050, CS-4050, CS-5050
"The phone receiver is off the hook."
CS-3050, CS-4050, CS-5050
"The removable memory is not formatted."
Is the removable memory formatted by this machine?
CS-3050, CS-4050, CS-5050
"The source file is not found."
CS-3035, CS-4035, CS-5035
"This name is already in use. Input new name
again."
CS-3035, CS-4035, CS-5035
"This number is already in use. Input new number
again."
CS-3050, CS-4050, CS-5050
"Top tray of the machine is full of paper."
The exit tray at the top of the machine is full.
CS-3050, CS-4050, CS-5050
Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher?
CS-3035, CS-4035, CS-5035
"Unable to find destination PC. Check the PC."
CS-3035, CS-4035, CS-5035
"Unable to find PC of personal address list."
There is a problem at the computer where the addressbook resides.
CS-3035, CS-4035, CS-5035
"Unable to find SMTP server. Contact administrator."
There is a networking problem to your SMTP server.
CS-3035, CS-4035, CS-5035
"Warning low memory."
"Wrong password." Wrong password has been entered.
CS-3050, CS-4050, CS-5050
Further scanning cannot be performed due to insufficient memory.
CS-3035, CS-4035, CS-5035
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
20 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn safety switch Off/On > 10871087
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
24
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
First try U906 partial reset. If code immediately returns format hard drive: 10871087
Start > Execute > Start (tech only)
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Power Off/On.
Turn power Off/On.
Turn power Off/On.
Service Checks1) Repl fax card.
1) Replace Main PWB EEPROM 3 and 4.
1) Repl fax card.
1) Repl main PWB.
1) Update firmware, 2) Install compatible fax card (Fax Sys (F) of Fax Sys (J)).
This code is stored but no displayed. 1) Run simulation U020 (initialize RAM), 2) Repl backup RAM.
1) Reload firmware, 2) Repl main PWB EEPROM 1 and 2. 3) Repl main PWB.
This code is stored but not displayed. 1) Reload firmware, 2) Repl main PWB EEPROMs. 3) Repl main PWB, 4) Contact Service Administrative Division.
1) Reload firmware, 2) Repl main PWB EEPROMs. 3) Repl main PWB, 4) Contact Service Administrative Division.
1) Reseat YC43 @ main PWB, and the connection to the printer PWB, 2) Repl printer PWB, 3) Repl main PWB.
1) Reseat YC46 @ main PWB, and the connection to the memory PWB, 2) Repl scanner PWB, 3) Repl main PWB.
1) Reseat YC44 @ main PWB, and the connection to the memory PWB, 2) Repl fax control PWB, 3) Repl main PWB.
1) Repl main PWB.
1) Reseat CN3 @ main PWB, and the connection to the deck main PWB or desk main PWB, 2) Repl deck main PWB or desk main PWB, 3) Repl main PWB.
1) Reseat YC4 & YC5 @ main PWB, and CN2 @ finisher main PWB, 2) Repl finisher main PWB, 3) Repl main PWB.
1) Reseat YC3 @ main PWB, and CN1 @ mailbox main PWB, 2) Repl mailbox main PWB, 3) Repl main PWB.
1) Reseat YC3 @ main PWB, 2) Repl switchback unit main PWB, 3) Repl main PWB.
1) Reseat the main DIMM, 2) Repl main DIMM, 2) Repl main PWB.
1) Reseat lower connector DP to copier, 2) Repl main PWB.
1) Power Off/On 2) Reseat YC49 @ main PCB, 3) Reformat HDD, 4) Repl main PWB
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Reseat YC44 @ main PWB, and the connection to the memory PWB, 2) Repl fax control PWB, 3) Repl main PWB.
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Update fax firmware to version 2.xx or later, 2) Repl fax control PWB.
1) Check for lift drive problem 2) Reseat YC13 @ main PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC13-B9 @ main PWB goes low when upper lift switch is OFF. If no, replace upper lift switch, 5) Repl main PWB.
1) Check for lift drive problem 2) Reseat YC13 @ main PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC13-B15 @ main PWB goes low when lower lift switch is OFF. If no, replace lower lift switch, 5) Repl main PWB.
1) Check for lift drive problem, 2) Reseat connectors on main PWB and desk main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check CN1-5 @ desk main PWB goes low when lift switch is OFF. If no, replace lift switch.
1) Check for lift drive problem 2) Reseat connectors on main PWB and desk main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check CN1-7 @ desk main PWB goes low when lift switch is OFF. If no, replace lift switch.
1) Check for deck motor drive problem, 2) Reseat paper deck motor 1 connector.
1) Check for deck motor drive problem, 2) Reseat paper deck motor 2 connector.
1) Check for lift drive problems, 2) Reseat connectors on main PWB and deck main PWB, 3) Pinout harnass, 4) Check CN5-4 @ deck main PWB goes low when deck level switch 2 is OFF. If no, repl deck level switch 2. 5) Repl paper deck lift motor 2.
1) Check for lift drive problems, 2) Reseat connectors on main PWB and deck main PWB, 3) Pinout harnass, 4) Check CN5-7 @ deck main PWB goes low when deck level switch 1 is OFF. If no, repl deck level switch 1. 5) Repl paper deck lift motor 1.
1) Check for drive problems, 2) Reseat YC11 @ main PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl main PWB.
1) Check for drive problems, 2) Reseat YC11 @ main PWB, 3) Pinout harnass, 4) Repl paper feed motor, 5) Repl main PWB .
1) Check for drive problems, 2) Reseat connectors on main PWB and desk main PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl desk main PWB, 6) Repl main PWB.
1) Check for drive problems, 2) Reseat connectors on main PWB and deck main PWB, 3) Pinout harnass, 4) Repl paper conveying motor, 5) Repl deck main PWB. 5) Repl main PWB.
1) Repl cleaning lamp, 2) Repl main PWB.
1) Check for drive problems, 2) Reseat YC37 @ main PWB, and YC4 @ scanner PWB, 3) Reseat YC4 (scanner home position switch) @ scanner PWB, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl scanner PWB, 7) Repl main PWB.
1) Reseat YC3 @ scanner PWB, 2) Reseat conn @ inverter PCB, 3) Reseat YC34 @ main PWB, 4) Pinout harnass, 5) Repl lamp & inverter PWB, 6) Repl main PWB.
1) Reseat connectors @ CCD PWB and YC34 @ main PWB, 2) Pinout harnass, 3) Repl lamp & inverter PWB, 4) Repl CCD PWB, 5) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Check YC2-1 @ main PWB for 24vdc. If absent, repl power source PWB. 5) Check YC8-10 @ main PWB for 24vdc. If absent, repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Check YC2-1 @ main PWB for 24vdc. If absent, repl power source PWB. 5) Check YC8-10 @ main PWB for 24vdc. If absent, repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Check that thermistor 1 and 2 are contacting heat roller & clean, and securely connected (check YC10 @ main PWB), 2) Check thermal switch, 3) Check fixing heaters M & S.
1) Reinsert fuser unit, 2) Repl fuser unit.
1) Reinsert drum unit, 2) Repl drum unit.
1) Shorted thermistor 1 or 2. Replace thermistor 1 or 2, 2) Replace power source PWB,
1) Open thermistor. Check that thermistor 1 and 2 are contacting heat roller & clean and not infinite resistance, 2) Reseat YC10 @ main PWB, 3) Check thermal switch, 3) Check fixing heaters.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC1-3 @ main PWB and YC2-6 @ power source PWB. 3) Check for zero-cross signal YC2-6 @ power source PWB. If absent, repl PSU (what waveform is expected?), 3) If present, repl main PWB.
1) Read resistance across thermistors. If infinite resistance replace thermistor, 2) Check YC10 @ main PWB, 3) Pinout harnass.
1) Replace toner container, 2) Reseat toner sensor connector, 3) Repl toner sensor, 4) Repl toner container sensor.
1) Reinsert image formation unit, 2) Repl image formation unit. (developing unit)
1) Reinsert image formation unit, 2) Repl image formation unit. (developing unit)
1) Reseat YC16-B7,B8,B9 @ main PWB (0utput: B8), 2) Pinout harnass, 3) Repl the humidity sensor.
1) Reseat YC16-B7,B8,B9 @ main PWB (0utput: B8), 2) Pinout harnass, 3) Repl the humidity sensor.
1) Check paper conveying motor PWB connectors, 2) Pinout harnass, 3) Repl paper conveying motor, 4) Repl finisher main PWB.
1) Reseat paper conveying belt clutch connector and home position senser, 2) Adjust the paper conveying belt so that it is in phase, 3) Repl paper conveying belt clutch, 4) Repl paper conveying belt home position sensor, 4) Check whether internal tray unit or front cover catches are damaged.
1) Reseat tray elevation motor connector, 2) Pinout harnass, 3) Repl tray elevation motor, 4) Repl finisher main PWB.
1) Reseat front side registration motor & HP sensor connectors, 2) Pinout harnass, 3) Repl front side registration motor, 4) Repl front side registration motor HP sensor, 5) Repl finisher main PWB.
1) Reseat rear side registration motor & HP sensor connectors, 2) Pinout harnass, 3) Repl rear side registration motor, 4) Repl rear side registration motor HP sensor, 5) Repl finisher main PWB.
1) Reseat trailing edge registration HPS connector, 2) Reseat trailing edge registration motor connector, 3) Repl trailing edge registration HPS, 4) Replace trailing edge registration motor, 5) Repl finisher main PWB.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
1) Unjam stapler, 2) Reseat stapler connector, 2) Repl stapler, 3) Repl finisher main PWB.
1) Unjam stapler, 2) Reseat stapler connector, 2) Repl stapler, 3) Repl finisher main PWB.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
See booklet stitcher service manual.
Try to perform the operation again.
1) Run mailbox communication test mode. If there is any communication problem replace mailbox drive motor, or mailbox main PWB.
Check to make sure that the destination computer is operating properly. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check to make sure that the computer that is running the personal Address Book is running properly.
Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly. Check with the network administrator to find out whether the SMTP server is working properly.
Check the restricted and/or permitted domain names, and adjust the settings as necessary. Check to make sure that the destination email address was entered correctly.
Check to make sure that the destination email address was entered correctly.
Check with your network administrator to find out whether the SMTP server is working properly.
Check the versions of the Scan File Utility.
Check the Scan File Utility Settings.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
Check to make sure that the Scan File Utility is running properly in that computer, or whether it is already connected to another scanner. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check the password that is set in the destination computer.
Increase the available space on the destination computer's hard drive, then try the operation again.
Try to perform the operation again after the connection to the other scanner is completed.
Perform any or all of the following procedures in order to lower the amount of data and then try scanning and transmission operation again: 1) lower the resolution of the image data. 2) Change the image quality setting to OCR. 3) Lower the number of documents (pages) that are being scanned at one time.
Check to make sure that the Scan File Utility in the destination computer is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, running in the destination computer. If the trouble is with the destination computer, fix the problem.
Load paper.
Check to make sure that the personal Address Book is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, also running on the computer that is running the personal Address Book. If the trouble is with the computer that is running the personal Address Book, fix that problem.
Check the computer of each group member as necessary and, if there is trouble in any of those computers, fix that problem.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
Check each error and fix the corresponding problems.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check is the server is operating properly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Set the number of pages to 999 or less.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Specify the destination address.
Select valid POP3 user other than [Other].
Check if the server is operating properly.
Check is the server is operating properly.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check is the server is operating properly.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Enter the correct host name or IP address.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Check the network connection (cable, network condition within LAN, etc.).
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct username/password.
Enter correct folder path.
Specify the destination address.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Select valid POP3 user other than [Other].
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Set the number of pages to 999 or less.
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Load paper. If the same type of paper is loaded in another cassette in the same orientation, you can press either one of the paper select keys on the left of the touch panel to switch to the cassette for copying.
Load paper of the size and type indicated in the MP tray.
Replace the toner container.
See above for details.
Close all covers securely.
Close the document processor.
Set the finisher correctly.
Leave the machine On and follow the instructions to replace the staple case. Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Document Box full: Press [End]. Repeat Copy Box full: Press [Continue] to copy without using Repeat Copy. Press [Cancel] to cancel job. See your key Operator/Administrator.
Press [End]. Then check: Registration of Authentication Server, Password & computer address of Authentication Server, Connection to the network. See your key Operator/Administrator.
Select another paper type. Press [Continue] to print without using duplex.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
Select another paper size. Press [Continue] to print without using offset.
Select another paper size/type. Press [Continue] to print without using punch.
Select another available paper size/type. Press [Continue] to print without stapling.
Check the correct domain name and hos name.
Clean the slit glass using the cleaning cloth supplied with the document processor.
Check the correct number and enter it again.
Consult your network administrator.
The job is cancelled. Press [End].
If you are using the Scan to PC function, check the status of the destination computer and then try the operation again. If you are using the Send E-mail function, check to make sure that the SMTP server is running, or consult your network administrator. If you are using the DB Assistant function, check to make sure that the DB Assistant is installed on the computer.
Connect the network cables of the computer and the machine properly.
Check to make sure thaqt the ScanFile Utility is runing at the destination computer.
Wait for a while and then try the operation again.
Check the status of the destination computer and then try the operation again.
Reduce the number of pages being transmitted, or lower the scaning resolution, and try to transmit again.
Follow the instructions on the touch panel to empty the punch waste box.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
The job is cancelled. Press [End]. See your key Operator/Administrator.
Retransmit after a while. Contact network administrator for check.
Remove paper from the folding tray.
Enter the correct user name or password.
Remove paper from the mailbox tray.
Format the memory card again.
1) Install fax system, 2) Check the connection of the flat cable. 3) Upgrade firmware. 4) Repl main PWB. 5) Retransmit after a while. 6) RTC memory is not mounted or poor connection. 7) Connect network cables properly. 8) Turn On main switch. 9) Check the IP address or hostname in the Fax driver and those registered in the scanner NIC.
1) Secure memory area (delecte data in the memory). 2) Add memory. 3) Retransmit originals with lower resolution. 4) Divide originals to be transmitted.
01: Initialization Error. Initialize the HDD. 04: Insufficient space on the HDD to complete this operation. Move or delete data stored on the HDD to increase available space.
Cannot print any more. This job is canceled. Press [End]. See your Key Operator/Administrator.
Remove paper from the job separator tray. Printing resumes.
The job is cancelled. Press [End]. See your Key Operator/Administrator.
When inserting the memory card turn Off the main switch first.
Move or delete data stored on the memory card to increase available space.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
1) Turn power Off/On.
Connect the scanner NIC properly.
Restart the scanner.
Wait a while and then try the operation again.
Press [End].
Register that destination or select another one.
Follow the displayed instructions to remove the jammed paper.
The job is paused. Press [Continue} to resume the job.
Delete any unnecessary items and try the procedure again.
This job is cancelled. Press [End]. Remove or replace the removable memory.
Remove originals from the document processor, put them back in their original order, stack them uniformly and place them again. Press [Continue] to resume printing. Press [Cancel] to cancel the job.
Replace the waste toner box. Two are included in the box with each toner.
Remove originals from the document processor.
Press [Continue] to print, send, or store the scanned pages. The job cannot be processed completely. Press [Cancel] to cancel printing, sending, or storing.
1) Reseat lower connector DP to copier, 1) Repl main PWB.
First register a user under that number (scanner sender defaults to 001) or turn the "Selec. Of senders (users)" setting to Off, then select another user.
Set the punch waste box correctly.
Set the waste toner box correctly.
Retransmit after a while.
Retransmit after a while.
Check the registered Account ID.
Retransmit after interrupt has been cleared.
Install the folding tray correctly to the 3,000 sheet finisher.
Install the folding unit correctly to the 3,000 sheet finisher.
Consult your network administrator to verify that the login account name and password required for SMTP Authentication are correct.
Follow the displayed instructions to remove the jammed staple.
Follow the displayed instructions to remove the jammed staple.
1) Turn On the main switch. 2) Retransmit after a while.
If the amount of data exceeds the maximum hard disk capacity as registered in the ScanFile Utility on the destination computer, increase the available space on your computer's hard disk and then try the operation again. If data with the same file name has been sent from more than one scanner at a time, the data can not be saved. Wait for a while and then try the operation again, or change the file name.
Put down the receiver.
The job is cancelled. Press [End].
Register a different name.
Register a different number.
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
Remove paper from the top exit tray, and press [Continue] to resume the job.
Remove output paper from the tray indicated on the panel. If tray B or C is full of paper press [Continue] to resume printing.
Check to make sure that the ScanFile Utility is running and the computer is able to receive data.
If the Addressbook software is not running on your computer, start it up. If it is already running, make sure that your computer is connected properly to the network and the network cable is connected properly to the scanner interface card.
Check to make sure that the network cable is connected securely and properly. If this message appears immediately after turning the scanner On, wait a while (~2 minutes) while the scanner warms up. In any other case, check to make sure that the SMTP server is running, or consult with your network administrator.
Check to make sure the the network cable is connected securely and properly. If this message appears immediately after turning the scanner On, wait a while (~2 minutes) while the scanner warms up.
Enter the correct password.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Model Error Code Description0xFBxx Undefined.
C0030
C0060 Main PWB Type Mismatch Error.
C0070
C0130
C0140
C0150
C0160
C0170
C0180
C0600 Main PWB DIMM Installed Incorrectly.
C0610 Main PWB DIMM error
C0630
C0640 Hard Disk Drive cannot be accessed
CS-3050 (2GN), CS-4050 (2GP), CS-5050
(2GR)
CS-3050, CS-4050, CS-5050
Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software.
CS-3050, CS-4050, CS-5050
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
CS-3050, CS-4050, CS-5050
Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
CS-3050, CS-4050, CS-5050
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
CS-3050, CS-4050, CS-5050
Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively.
CS-3050, CS-4050, CS-5050
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
CS-3050, CS-4050, CS-5050
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-3050, CS-4050, CS-5050
C0700 Optional CF backup is not suitable.
C0800
C0830
C0870
C0880 Fax PWB program archive problem.
C0920 Fax backup data is not retained.
C1010
C1020
C1030
C1040
C1100
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Image processing problem. JAM05 is detected twice.
CS-3050, CS-4050, CS-5050
Fax Flash ROM program area checksum error
CS-3050, CS-4050, CS-5050
Fax PWB to Main PWB high capacity data transfer problem.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
CS-3050, CS-4050, CS-5050
Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
CS-3050, CS-4050, CS-5050
PF-700 optional cassette #3 lift motor error.
CS-3050, CS-4050, CS-5050
PF-700 optional cassette #4 lift motor error.
CS-3050, CS-4050, CS-5050
PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.
C1110
C1120
C1130
C1800 PF-700/PF-750 Communication Problem.
C1900
C2000
C2250
C2500
C2600
C2600
CS-3050, CS-4050, CS-5050
PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.
CS-3050, CS-4050, CS-5050
PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off after 30 seconds of motor operation.
CS-3050, CS-4050, CS-5050
PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off after 30 seconds of motor operation.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
PF-700 EEPROM error. Write data & Read data are not in agreement three times consecutively.
CS-3050, CS-4050, CS-5050
Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation.
CS-3050, CS-4050, CS-5050
Main Charge Cleaner Motor error. Lock error is detected three times in a row during cleaner motor operation.
CS-3050, CS-4050, CS-5050
Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation.
CS-3050, CS-4050, CS-5050
PF-700 Drive Motor error. Lock signal exceeds 500ms.
CS-3050, CS-4050, CS-5050
PF-750 Paper Conveying Motor error. Lock signal exceeds 450ms.
C3100
C3200
C3210
C3300
C3310
C3500
C3900
C3910
C4000
C4010
C4200
CS-3050, CS-4050, CS-5050
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
CS-3050, CS-4050, CS-5050
Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of commencing reading.
CS-3050, CS-4050, CS-5050
Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading.
CS-3050, CS-4050, CS-5050
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
CS-3050, CS-4050, CS-5050
CIS AGC Problem. After AGC correct input is not obtained at the CIS.
CS-3050, CS-4050, CS-5050
Communication Error Between Scanner and SHD.
CS-3050, CS-4050, CS-5050
Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match.
CS-3050, CS-4050, CS-5050
Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
CS-3050, CS-4050, CS-5050
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
CS-3050, CS-4050, CS-5050
Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.
CS-3050, CS-4050, CS-5050
BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization.
C5300
C6000
C6020
C6030
C6050
C6400
C6410
C6420
C7300
C7400
C7410
C7800
C7810
CS-3050, CS-4050, CS-5050
Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously.
CS-3050, CS-4050, CS-5050
Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at least 1C/1.8F within 5 sec.
CS-3050, CS-4050, CS-5050
Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more.
CS-3050, CS-4050, CS-5050
Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.
CS-3050, CS-4050, CS-5050
Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying.
CS-3050, CS-4050, CS-5050
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
CS-3050, CS-4050, CS-5050
Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.
CS-3050, CS-4050, CS-5050
Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse cut signal is turned on.
CS-3050, CS-4050, CS-5050
Toner Container Problem. Toner level is not detected when toner empty is detected.
CS-3050, CS-4050, CS-5050
Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.
CS-3050, CS-4050, CS-5050
Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
CS-3050, CS-4050, CS-5050
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
CS-3050, CS-4050, CS-5050
Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
C7900
C7910
C8020
C8030
C8050
C8060
C8070
CS-3050, CS-4050, CS-5050
Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-3050, CS-4050, CS-5050
Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-3050, CS-4050, CS-5050
DF-710 Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation.
CS-3050, CS-4050, CS-5050
DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.
CS-3050, CS-4050, CS-5050
DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
CS-3050, CS-4050, CS-5050
DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 2.5 sec.
CS-3050, CS-4050, CS-5050
DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
C8140
C8140
C8170
C8170
C8170
C8180
CS-3050, CS-4050, CS-5050
DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray capacity detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray load detection sensor remain on for 2 sec or more during main tray ascent.
CS-3050, CS-4050, CS-5050
DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec.
CS-3050, CS-4050, CS-5050
DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
CS-3050, CS-4050, CS-5050
DF-720 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
CS-3050, CS-4050, CS-5050
DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation.
CS-3050, CS-4050, CS-5050
DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
C8180
C8190
C8210
C8210
C8210
C8220
C8230
C8300
CS-3050, CS-4050, CS-5050
DF-720 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
CS-3050, CS-4050, CS-5050
DF-720 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
CS-3050, CS-4050, CS-5050
DF-710 Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
CS-3050, CS-4050, CS-5050
DF-720 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.
CS-3050, CS-4050, CS-5050
DF-730 Stapler Problem. Home position is not detected within a specific time of activation.
CS-3050, CS-4050, CS-5050
DF-710 Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
CS-3050, CS-4050, CS-5050
DF-710 Stapler Motor Problem. Jam 82 is indicated.
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
C8310
C8320
C8330
C8340
C8350
C8360
C8440
C8460
C8500
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
CS-3050, CS-4050, CS-5050
BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Staple Motor Problem. Jam 89.
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
CS-3050, CS-4050, CS-5050
BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
CS-3050, CS-4050, CS-5050
DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
CS-3050, CS-4050, CS-5050
DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed.
CS-3050, CS-4050, CS-5050
MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox.
C8510
C8800
C8900
C8910
C8920
C8930
C9000
C9040
C9050
C9060
C9070
CS-3050, CS-4050, CS-5050
MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.
CS-3050, CS-4050, CS-5050
DF-710 Communication Problem. No communication: there is no reply after (5) tries. Abnormal communication: a parity or checksum error is detected (5) times in succession.
CS-3050, CS-4050, CS-5050
DF-710 Backup Memory Data Problem. Read and write data does not match.
CS-3050, CS-4050, CS-5050
PH-5A Backup Memory Data Problem. Read and write data does not match.
CS-3050, CS-4050, CS-5050
MT-710 Backup Memory Data Problem. Read and write data does not match.
CS-3050, CS-4050, CS-5050
BF-710 Backup Memory Data Problem. Read and write data does not match.
CS-3050, CS-4050, CS-5050
DP-700 Communication Problem. A communication error is detected.
CS-3050, CS-4050, CS-5050
DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned On.
CS-3050, CS-4050, CS-5050
DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned On.
CS-3050, CS-4050, CS-5050
DP-700 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
CS-3050, CS-4050, CS-5050
DP-700 Communication Error between the DP and SHD. A communication error is detected.
C9080
CF000
CF010
CF020
CF030 Main PWB System Error.
CF040 Engine PWB Communication Error.
CF041 Scanner PWB Communication Error.
CF050 Engine ROM Checksum Error.
CF060 Engine RAM Error.
CF070
CF080
CF090 Fax System M Communication Error.
CF14F
CF256
CF257
CS-3050, CS-4050, CS-5050
DP-700 Communication Error between the DP and CIS. Reading cannot be performed correctly.
CS-3050, CS-4050, CS-5050
Operation Panel PWB Communication Error/System Error. Unknown error. Communication error between panel and main controller. (If CF620 occurred and is left, CF000 also occurred because of timeout control.
CS-3050, CS-4050, CS-5050
Main PWB Checksum Error/System Error. Communication error between panel and main controller.
CS-3050, CS-4050, CS-5050
Memory Checksum Error/Operation System Error.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Flash ROM Error. Defective flash ROM (which?).
CS-3050, CS-4050, CS-5050
Flash ROM Error (during download). Defective flash ROM (which?).
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
CS-3050, CS-4050, CS-5050
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CS-3050, CS-4050, CS-5050
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF26F
CF3xx Undefined.
CF423
CF423
CF5xx Undefined.
CF610 System Start Error.
CF620
CS-3050, CS-4050, CS-5050
Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CS-3050, CS-4050, CS-5050
Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CS-3050, CS-4050, CS-5050
CF433 CF434 CF437 CF43F CF441 CF444
CF445 CF451
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CS-3050, CS-4050, CS-5050
CF45F CF453 CF454 CF45F CF460 CF463
CF46F CF470
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CS-3050, CS-4050, CS-5050
CF473 CF47F CF484 CF487 CF48F CF490
CF493 CF494
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
System Error. Error acquiring the event data. Panel detects CF000 as same error.
CF620
CF7D7
CFAxx HDD Error.
CFB2C CFB30 CFB31
CFB30
CFB31 Corrupt Firmware on Main EEPROM.
CFB32
CFB33
F000
F010 Main PWB Checksum Error.
F020 Memory Checksum Error.
F030 Main PWB System Error.
F040 Engine PWB Communication Error.
F041 Scanner PWB Communication Error.
F050 Engine ROM Checksum Error.
F060 Engine RAM Error.
CS-3050, CS-4050, CS-5050
System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
CS-3050, CS-4050, CS-5050
Readout Error of SSL (authentication data).
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
CS-3050, CS-4050, CS-5050
Incompatible Level Of Firmware on Main EEPROM.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Panel Error. Timeout request for start up command. Start command hasn't been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CS-3050, CS-4050, CS-5050
Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CS-3050, CS-4050, CS-5050
Operation Panel PWB Communication Error.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
F070 Flash ROM Error.
F080 Flash ROM Error (during download).
F090 Fax Control PWB Communication Error.
F14F Power Source PWB Second Side Error.
E00000 or U00000
E00100 or U00100
E00200 or U00200
E00300 or U00300
E00420 or U00420
E00421 or U00421
E00430 or U00430
E00430 or U00430
E00431 or U00431
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Fax Communication Error: No response or line busy after the set number of redials.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Recording paper on the destination unit has run out during reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00431 or U00431
E00432 or U00432
E00432 or U00432
E00433 or U00433
E00433 or U00433
E00434 or U00434
E00435 or U00435
E00435 or U00435
E00440 or U00440
CS-3050, CS-4050, CS-5050
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
E00440 or U00440
E00440 or U00440
E00441 or U00441
E00450 or U00450
E00460 or U00460
E00460 or U00460
E00462 or U00462
E00500 or U00500
E00600 or U00600
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
CS-3050, CS-4050, CS-5050
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
CS-3050, CS-4050, CS-5050
Fax Communication Error: The document processor cover is open.
E00601 or U00601
E00602 or U00602
E00603 or U00603
E00604 or U00604
E00610 or U00610
E00611 or U00611
E00613 or U00613
E00614 or U00614
E00615 or U00615
E00620 or U00620
E00622 or U00622
E00655 or U00655
E00656 or U00656
E00670 or U00670
E00677 or U00677
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700
E00800 or U00800
CS-3050, CS-4050, CS-5050
Fax Communication Error: Document jam or the document length exceeds the maximum.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Image scanning section problem
CS-3050, CS-4050, CS-5050
Fax Communication Error: No document feed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Recording section cover open.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Recording paper jam.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Image writing section problem.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Nearly empty of recording paper.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Empty of recording paper.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Copier fixing unit problem.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Copier drive motor problem.
CS-3050, CS-4050, CS-5050
Fax Communication Error: CTS was not activated after RTS due to a modem error.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Power was cut off during communication.
CS-3050, CS-4050, CS-5050
Fax Communication Error: There was no file to transmit in the memory transmission mode.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810
E00900 or U00900
E00910 or U00910
E01000 or U01000
E01000 or U01000
E01001 or U01001
E01010 or U01010
E01011 or U01011
CS-3050, CS-4050, CS-5050
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012
E01013 or U01013
E01014 or U01014
E01015 or U01015
E01016 or U01016
E01017 or U01017
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018
E01019 or U01019
E01020 or U01020
E01021 or U01021
E01022 or U01022
E01023 or U01023
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024
E01025 or U01025
E01026 or U01026
E01027 or U01027
E01028 or U01028
E01040 or U01040
E01041 or U01041
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042
E01043 or U01043
E01044 or U01044
E01045 or U01045
E01046 or U01046
E01047 or U01047
E01048 or U01048
E01049 or U01049
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050
E01051 or U01051
E01052 or U01052
E01053 or U01053
E01054 or U01054
E01055 or U01055
E01056 or U01056
E01057 or U01057
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070
E01071 or U01071
E01072 or U01072
E01073 or U01073
E01080 or U01080
E01091 or U01091
E01092 or U01092
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E01100 or U01100
E01101 or U01101
E01102 or U01102
E01110 or U01110
E01111 or U01111
E01112 or U01112
E01113 or U01113
E01114 or U01114
E01115 or U01115
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116
E01117 or U01117
E01118 or U01118
E01119 or U01119
E01120 or U01120
E01121 or U01121
E01122 or U01122
E01123 or U01123
E01124 or U01124
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125
E01126 or U01126
E01127 or U01127
E01128 or U01128
E01129 or U01129
E01140 or U01140
E01141 or U01141
E01142 or U01142
E01143 or U01143
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144
E01145 or U01145
E01146 or U01146
E01147 or U01147
E01148 or U01148
E01149 or U01149
E01150 or U01150
E01151 or U01151
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
E01152 or U01152
E01153 or U01153
E01154 or U01154
E01155 or U01155
E01160 or U01160
E01161 or U01161
E01162 or U01162
E01163 or U01163
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
E01164 or U01164
E01170 or U01170
E01172 or U01172
E01191 or U01191
E01199 or U01199
E01400 or U01400
E01500 or U01500
E01600 or U01600
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
CS-3050, CS-4050, CS-5050
Fax Communication Error: An invalid one-touch key was specified during communication.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700
E01720 or U01720
E01721 or U01721
E01800 or U01800
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810
E01820 or U01820
E02000 or U02000
E02100 or U02100
E02200 or U02200
E02200 or U02200
E02200 or U02200
E02303 or U02303
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
CS-3050, CS-4050, CS-5050
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
E02304 or U02304
E02400 or U02400
E03000 or U03000
E03100 or U03100
E03200 or U03200
E03200 or U03200
E03300 or U03300
E03300 or U03300
E03400 or U03400
E03500 or U03500
CS-3050, CS-4050, CS-5050
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
CS-3050, CS-4050, CS-5050
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: No document was present in the destination unit when polling reception started.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
E03500 or U03500
E03500 or U03500
E03600 or U03600
E03600 or U03600
E03700 or U03700
E03700 or U03700
E04000 or U04000
E04000 or U04000
E04000 or U04000
CS-3050, CS-4050, CS-5050
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: The destination was being accessed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS-3050, CS-4050, CS-5050
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: The destination was being accessed.
E04100 or U04100
E04100 or U04100
E04200 or U04200
E04300 or U04300
E04400 or U04400
E04401 or U04401
E04500 or U04500
E05000 or U05000
E05100 or U05100
CS-3050, CS-4050, CS-5050
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200
E05300 or U05300
E09000 or U09000
E12000 or U12000
E12000 or U12000
E12100 or U12100
E14000 or U14000
E14000 or U14000
E14100 or U14100
E14100 or U14100
E19000 or U19000
CS-3050, CS-4050, CS-5050
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
CS-3050, CS-4050, CS-5050
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: In subaddress-based relay reception memory overflowed.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed during confidential reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100
E19200 or U19200
E19300 or U19300
E19400 or U19400
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1102
Send SMB Error 1103
Send SMB Error 1103
Send SMB Error 1103
Send SMB Error 1105
Send SMB Error 2101
Send SMB Error 2101
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory overflowed in the destination unit during transmission.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Memory transmission failed because a decoding error occurred.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
CS-3050, CS-4050, CS-5050
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
CS-3050, CS-4050, CS-5050
Error: Username/Password or Shared Name/Folder Name. Host name error.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. SMB protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Assign the wrong port number.
Send SMB Error 2101
Send SMB Error 2103
Send SMB Error 2201
Send SMB Error 2203
Send SMB Error 9181
Send FTP Error 1101
Send FTP Error 1102
Send FTP Error 1102
Send FTP Error 1103
Send FTP Error 1103
Send FTP Error 1105
Send FTP Error 2101
Send FTP Error 2101
Send FTP Error 2101
Send FTP Error 2102
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Host Name. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Username/Password. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Error: Username/Password. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. FTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Assign the wrong port number.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. The server is unable to communicate.
Send FTP Error 2102
Send FTP Error 2103
Send FTP Error 2201
Send FTP Error 2202
Send FTP Error 2203
Send FTP Error 3101
Send FTP Error 9181
Send email Error 1101
Send email Error 1102
Send email Error 1104
Send email Error 1105
Send email Error 1106
Send email Error 2101
Send email Error 2101
Send email Error 2101
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Host Name. SMTP server name is not set. Error SMTP server name.
CS-3050, CS-4050, CS-5050
Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
CS-3050, CS-4050, CS-5050
Error: No Recipient Address. The destination address is not specified.
CS-3050, CS-4050, CS-5050
Error: Not Supported Protocol. SMTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Error: No Sender Info. Sender address is not entered.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. The specified server is not SMTP server.
CS-3050, CS-4050, CS-5050
Error: Can Not Connect. Network is not connected.
Send email Error 2102
Send email Error 2103
Send email Error 2201
Send email Error 2202
Send email Error 2203
Send email Error 2204
Send email Error 3101
Send email Error 3101
Send email Error 3201
Send email Error 9181
TWAIN Error 2202
TWAIN Error 9181
Software Error 5101
Software Error 5102
Software Error 5103
CS-3050, CS-4050, CS-5050
Error: Cannot Connect With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Error: Email Size Limit. The size of the email attachment exceeds its limit.
CS-3050, CS-4050, CS-5050
Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Error: Server Response. Server setting is not authenticated normally.
CS-3050, CS-4050, CS-5050
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
CS-3050, CS-4050, CS-5050
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Not Yet Opened. Error for storage status in the operation handle.
Software Error 5104
Software Error 7101
Software Error 7102
Software Error 720f
CS-3050, CS-4050, CS-5050
Error: Already Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Error: Memory Allocation. Insufficient memory space.
CS-3050, CS-4050, CS-5050
Error: Socket Create. Unable to create a communication socket.
CS-3050, CS-4050, CS-5050
Error: Unknown Error. Unable to determine the cause.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1101
Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1101
Send FTP Error: Host Name. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1104
Send Email Error: No Recipient Address. The destination address is not specified.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1105
Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
1106
Send Email Error: No Sender Info. Sender address is not entered.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. The specified server is not SMTP server.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Network is not connected.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2102
Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2102
Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2103
Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2201
Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2202
Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2202
Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2203
Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
2204
Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3101
Send Email/FTP Error: Server Response. The server is error status.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3101
Send Email Error: Server Response. Server setting is not authenticated normally.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
3201
Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5101
Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Is the acceptable staple count exceeded?
"Add paper in cassette #." Is the indicated cassette out of paper?
"Add paper in MP tray."
"Add staples."
"Add toner."
"An error has occurred."
"Box Limit Exceeded."
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5102
Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5103
Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
5104
Send Software Error: Already Opened. Error for storage status in the operation handle.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
7102
Send Software Error: Socket Create. Unable to create a communication socket.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
720f
Send Software Error: Unknown Error. Unable to determine the cause.
CS-3050, CS-4050, CS-5050
Send error. Job is cancelled. Press [End].
9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
CS-3050, CS-4050, CS-5050
"Acceptable staple count exceeded."
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Is the paper of the specified size loaded in the multipurpose tray?
CS-3050, CS-4050, CS-5050
Has the document finisher run out of staples?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
An internal error has occurred.Make a note of the error code number displayed on the panel. See above.
CS-3050, CS-4050, CS-5050
Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
"Cannot execute this job." Job is restricted by Job Accounting.
"Cannot offset this paper."
"Cannot staple this paper."
"Check the cover."
"Check the finisher." Is the document finisher set correctly?"
"Clean the slit glass." Dirt has been identified on the slit glass.
"Fax box limit exceeded."
CS-3050, CS-4050, CS-5050
"Cannot connect to Authentication Server."
CS-3050, CS-4050, CS-5050
"Cannot duplex print on this paper."
Did you select a paper size/type that cannot be duplex printed?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
CS-3050, CS-4050, CS-5050
"Cannot punch this paper type."
Did you select a paper size/type that cannot be punched?
CS-3050, CS-4050, CS-5050
Did you select a paper size/type that cannot be stapled?
CS-3050, CS-4050, CS-5050
Are any covers open? Does the message indicate which cover is open?
CS-3050, CS-4050, CS-5050
"Check the document processor."
Is the document processor open? Is the top cover of the document processor open?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
"Empty the punch waste box."
The punch waste box of the 3,000 sheet finisher is full.
CS-3050, CS-4050, CS-5050
"Failed to specify Job Accounting."
Job accounting is not specified in the print driver.
CS-3050, CS-4050, CS-5050
"Failed to store job retention data."
CS-3050, CS-4050, CS-5050
Fax box is full, and no further storage is available.
CS-3050, CS-4050, CS-5050
"Finisher tray is full of paper."
Is the acceptable storage capacity exceeded for the document finisher tray?"
An error has occurred on the hard disk.
"KPDL error." A PostScript error has occurred.
"Memory card error."
Memory Card Error: Format error.
"Memory is full."
"Memory Is Low" Logic Lockup
"Paper Jam. ###"
"Print overrun." Warning. Low printer memory.
CS-3050, CS-4050, CS-5050
"Folding tray is full of paper."
Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?"
CS-3050, CS-4050, CS-5050
"Hard Disk error. Job is cancelled. Press [End] ##"
CS-3050, CS-4050, CS-5050
"Incorrect Login User Name or Password."
CS-3050, CS-4050, CS-5050
"Job Accounting restriction exceeded."
The print count exceeded the acceptable count restricted by Job Accounting.
CS-3050, CS-4050, CS-5050
"Job Separator is full of paper."
Is the maximum capacity of the job separator tray exceeded?
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
"Mailbox tray is full of paper."
CS-3050, CS-4050, CS-5050
Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted?
CS-3050, CS-4050, CS-5050
"Memory card error. Job is cancelled. Press [End].
Code: 01
CS-3050, CS-4050, CS-5050
"Memory card error. Job is cancelled. Press [End].
Code: 04
Memory Card Error: Insufficient memory card space to complete this operation.
CS-3050, CS-4050, CS-5050
Unable to continue the job, as the memory is used up."
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Make a note of the jam location number displayed on the panel. Leave the machine On.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
"Removable memory error."
An error has occurred on the USB stick memory or Compact Flash memory.
CS-3050, CS-4050, CS-5050
"Removable memory was removed."
The waste toner box is full.
"Scanner memory is full."
"Scanner Paused"
"Set the folding tray."
"Set the folding unit."
"Set the waste toner box."
"Staple error."
"Staple jam."
"The ID is not registered." The account ID# does not match.
CS-3050, CS-4050, CS-5050
"Replace all originals and press [Continue]."
CS-3050, CS-4050, CS-5050
"Replace the waste toner box."
CS-3050, CS-4050, CS-5050
"Reset all originals in the document processor."
Are there any originals left in the document processor?
CS-3050, CS-4050, CS-5050
Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
CS-3050, CS-4050, CS-5050
DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-3050, CS-4050, CS-5050
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
CS-3050, CS-4050, CS-5050
Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
CS-3050, CS-4050, CS-5050
"Set the punch waste box."
The waste toner box is not installed correctly.
CS-3050, CS-4050, CS-5050
The waste toner box is not installed correctly.
CS-3050, CS-4050, CS-5050
The location of the jam will be indicated on the panel. Leave the machine On.
CS-3050, CS-4050, CS-5050
The location of the jam will be indicated on the panel. Leave the machine On.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
"The memory card is not formatted."
Is the removable memory formatted by this machine?
CS-3050, CS-4050, CS-5050
"The phone receiver is off the hook."
CS-3050, CS-4050, CS-5050
"The removable memory is not formatted."
Is the removable memory formatted by this machine?
The specified file is not found.
"Tray # is full of paper."
"Warning low memory."
CS-3050, CS-4050, CS-5050
"The source file is not found."
CS-3050, CS-4050, CS-5050
"Top tray of the machine is full of paper."
The exit tray at the top of the machine is full.
CS-3050, CS-4050, CS-5050
Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher?
CS-3050, CS-4050, CS-5050
Further scanning cannot be performed due to insufficient memory.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
24
Turn power Off/On. If code immediately returns initialize backup data for image processing: Status > 10871087
Start > Main+Engine > Inch > Start > power Off/On. (tech only)
First try turning power Off/On. If code immediately returns format hard drive: Status > 10871087
Start > Execute > Start (tech only)
933
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Power Off. Reseat BU-10 CF card. Power On. If code immediately returns initialize CF: Status > 10871087
Start > RECOVERY CF > Start > power Off/On >FAX IMAGE > Execute > Start > INITIALIZE CF > Start > power Off/On (tech only)
First try turning power Off/On. If code immediately returns reload fax firmware.
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data for scanning: Status > 10871087
Start > SCANNER > Start > power Off/On. > Status > 10871087 > 411 > see service manual pg 107 (tech only)
Turn power Off/On.
Status > 10871087 163 Start > Execute > Start
Status > 10871087 163 Start > Execute > Start
Status > 10871087 163 Start > Execute > Start
Status > 10871087 163 Start > Execute > Start
Status > 10871087 163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Status > 10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Turn power Off/On.
Turn power Off/On.
Service Checks
1) Repl fax card.
1) Repl main PWB.
1) Reinstall main DIMM.
1) Repl main DIMM, 2) Repl main PWB.
1) Install compatible fax card (Fax Sys M (B)).
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Run simulation U022, 2) Repl engine PWB.
1) Run simulation U022, 2) Repl engine PWB, 3) Repl main PWB.
1) Contact Kyocera Service Administrative Division, 2) Repl engine PWB, 3) Repl main PWB.
1) Reseat lower connector DP to copier, 2) Repl main PWB.
1) Power Off/On 2) Reseat YC49 @ main PCB, 3) Reformat HDD, 4) Repl main PWB
1) Reseat BU10 CF, 2) Run sim U933.
1) Repl main PWB.
1) Reload firmware, 2) Repl fax card.
1) Repl fax card.
1) Power Off/On 2) Repl fax card.
1) Reseat YC1 @ Fax, YC4 & YC6 @ interface, YC30 @ main PWB, 2) Repl fax card, 3) Repl main PWB
1) Check for lift drive problem 2) Reseat YC13 @ engine PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC13-B9 @ engine PWB goes low when upper lift switch is OFF. If no, replace upper lift switch, 5) Repl engine PWB.
1) Check for lift drive problem 2) Reseat YC13 @ engine PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC13-B15 @ engine PWB goes low when lower lift switch is OFF. If no, replace lower lift switch, 5) Repl engine PWB.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-5 @ PF main PWB goes low when lift switch 1 is OFF. If no, replace lift switch 1.
1) Check for lift drive problem 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-7 @ PF main PWB goes low when lift switch 2 is OFF. If no, replace lift switch 2.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB.
1) Check for lift drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-7 @ PF Main PWB goes low when lift switch 2 is OFF. If no, repl lift switch 2. 5) Repl lift motor.
1) Check for lift drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-4 @ PF Main PWB goes low when lift switch 1 is OFF. If no, repl lift switch 1. 5) Repl lift motor.
1) Reseat connectors on engine PWB and PF main PWB, 2) Pinout harnass, 3) Repl engine PWB, 4) Repl PF main PWB.
1) Reseat connectors on engine PWB and PF main PWB, 2) Pinout harnass, 3) Repl engine PWB, 4) Repl PF main PWB.
1) Check for drive problems, 2) Reseat YC11 @ engine PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC9 @ engine PWB, 3) Pinout harnass, 4) Repl main charge cleaning motor, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC11 @ engine PWB, 3) Pinout harnass, 4) Repl paper feed motor, 5) Repl engine PWB .
1) Check for drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl PF main PWB, 6) Repl engine PWB.
1) Check for drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl paper conveying motor, 5) Repl PF main PWB. 5) Repl engine PWB.
1) Repl scanner PWB.
1) Check for drive problems, 2) Reseat YC4 @ scanner PWB, 3) Reseat connector on scanner home position switch, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl scanner PWB.
1) Reseat YC6 @ scanner PWB, 2) Reseat conn @ inverter PCB, 3) Pinout harnass, 4) Adj position of shading plate, 5) Repl home position switch, 6) Repl lamp & inverter PWB, 7) Repl scanner PWB, 8) Replace CCD PWB.
1) Reseat conn @ main PWB & DP main PWB, 2) Pinout harnass, 3) Replace inverter PWB, 4) Repl CIS, 5) Repl DP main PWB.
1) Reseat connectors @ SHD PWB & CCD PWB, 2) Pinout harnass, 3) Repl lamp & inverter PWB, 4) Repl SHD PWB, 5) Repl CCD PWB.
1) Repl DP inverter PWB, 2) Repl CIS, 3) Repl DP Main PWB.
1) Reseat YC3 @ scanner PWB & YC4 @ SHD PWB, 2) Pinout harnass, 3) Repl Scanner PWB, 4) Repl SHD PWB.
1) Run simulation U022, 2) Repl scanner PWB.
1) Reseat YC8 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Reseat YC8 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Reseat YC8 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Repl cleaning lamp, 2) Repl engine PWB.
1) Reinsert fuser unit, 2) Repl fuser unit.
1) Reinsert drum unit, 2) Repl drum unit.
1) Check that thermistor1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters, 4) Repl PSU, 5) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1 or 2, 3) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1 or 2, 3) Repl engine PWB.
1) Check that thermistor1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters 4) Repl PSU, 5) Repl engine PWB.
1) Check wall outlet ground to neutral voltage. 2) Repl PSU, 3) Repl engine PWB.
1) Reinsert fuser unit, 2) Check YC10 @ engine PWB, 3) Pinout harnass.
1) Check YC9 @ engine PWB, 2) Pinout harnass, 3) Replace toner container sensor.
1) Reinsert developing unit, 2) Repl developing unit.
1) Reseat YC14 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Reseat YC14 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Pinout harnass, 2) Repl drum unit.
1) Pinout harnass, 2) Repl developing unit.
1) Check punch PWB connectors, 2) Pinout harnass, 3) Repl punch motor, 4) Repl punch PWB, 5) Repl finisher PWB.
1) Reseat connectors, 2) Pinout harnass, 3) Repl upper limit sensor or paper push sensor, 4) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & paper conveying belt motor 1 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS1, 4) Repl paper conveying belt motor 1, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC6 @ internal tray PWB & paper conveying belt motor 2 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS2, 4) Repl paper conveying belt motor 2, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC1 @ internal tray PWB & YC6 @ finisher main PWB, 2) Pinout harnass, 3) Repl internal tray PWB, 4) Repl finisher main PWB.
1) Reseat YC6 @ finisher main PWB & connector for main tray motor, 2) Pinout harnass, 3) Replace main tray upper & lower limit detection switches & main tray load detection sensor, 4) Repl main tray motor, 5) Repl finisher main PWB.
1) Reseat connectors or Replace tray lower limit sensor, push paper sensor, surface view sensor, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & side registration motor 1 connector, 2) Pinout harnass, 3) Repl side registration motor 1, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat front registration HPS, 2) Reseat front registration motor connector, 3) Repl front registration HPS, 4) Replace front registration motor, 5) Repl finisher main PWB.
1) Reseat sensor connectors, 2) Reseat motor connectors, 3) Pinout harnass, 4) Repl adjustment home position sensor. 5) Repl adjustment motor, 6) Replace finisher main PWB.
1) Reseat YC8 @ internal tray PWB & side registration motor 2 connector, 2) Pinout harnass, 3) Repl side registration motor 2, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat rear registration HPS connector, 2) Reseat rear registration motor connector, 3) Repl rear registration HPS, 4) Replace rear registration motor, 5) Repl finisher main PWB.
1) Reseat trailing edge registration HPS connector, 2) Reseat trailing edge registration motor connector, 3) Repl trailing edge registration HPS, 4) Replace trailing edge registration motor, 5) Repl finisher main PWB.
1) Reseat YC9 @ finisher main PWB & stapler moving motor 1 connector, 2) Repl stapler moving motor 1, 3) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl front stapler assy, 4) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl stapler assy, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler moving motor 2 connector, 2) Replace stapler moving motor 2, 3) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler motor connector, 2) Replace stapler motor, 3) Repl finisher main PWB.
1) Reseat YC22 @ finisher main PWB, 2) Replace centerfold unit set switch, 3) Repl finisher main PWB.
1) Repl finisher main PWB.
1) Reseat YC6 @ centerfold main PWB & centerfold side registration motor 1 connector, 2) Repl centerfold side registration motor 1, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC6 & YC7 @ centerfold main PWB & centerfold paper conveying motor belt 1/2 connector, 2) Repl centerfold paper conveying belt motor 1/2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC8 @ centerfold main PWB & blade motor connector, 2) Repl blade motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC9 @ centerfold main PWB & centerfold staple motor connector, 2) Repl centerfold staple motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC7 @ centerfold main PWB & centerfold side registration motor 2 connector, 2) Repl centerfold side registration motor 2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC12 @ centerfold main PWB & centerfold main motor connector, 2) Repl centerfold main motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat paper entry sensor connector, 2) Clean foreign matter from paper entry sensor, 3) Repl paper entry sensor, 4) Repl finisher main PWB.
1) Reseat YC7 @ finisher main PWB & connections to the mailbox, 2) Repl mailbox main PWB, 3) Repl finisher main PWB.
1) Reseat YC2 @ mailbox main PWB & mailbox drive motor connector, 2) Repl mailbox drive motor, 3) Repl mailbox main PWB, 4) Repl finisher main PWB.
1) Reeat all connectors @ engine PWB & finisher main PWB. 2) Repl finisher main PWB, 3) Repl engine PWB.
1) Reseat all connectors @ engine PWB & finisher main PWB. 2) Repl finisher main PWB, 3) Repl engine PWB.
1) Reseat all connectors @ punch PWB & YC4 @ finisher main PWB. 2) Repl punch PWB.
1) Reseat all connectors @ mailbox PWB & YC7 @ finisher main PWB. 2) Repl mailbox main PWB.
1) Reseat all connectors @ centerfold main PWB & YC5 @ finisher main PWB. 2) Repl centerfold main PWB.
1) Reseat YC7 @ scanner PWB & the pigtail to the copier, 2) Repl DP main PWB.
1) Reseat lift upper limit switch connector, 2) Reseat DP lift motor connector 3) Repl DP lift upper limit switch, 4) Repl DP lift motor, 5) Repl DP main PWB.
1) Reseat lift lower limit switch connector, 2) Reseat DP lift motor connector 3) Repl DP lift lower limit switch, 4) Repl DP lift motor, 5) Repl DP main PWB.
1) Repl DP main PWB, 2) Contact Service Administration Division.
1) Reseat all connectors @ SHD PWB, 2) Pinout connectors/harnass, 3) Repl SHD PWB.
1) Repl main PWB.
1) Repl main PWB, 2) Repl engine PWB.
1) Repl main PWB, 2) Repl scanner PWB.
1) Repl engine PWB.
1) Repl engine PWB.
1) Repl flash ROM.
1) Repl flash ROM.
1) Repl main PWB.
1) Reinstall fax sys M, 2) Repl fax sys M.
1) Reinstall fax sys M, 2) Repl fax sys M.
1) Reseat all connectors @ CIS, 2) Pinout connectors/harnass, 3) Repl CIS.
1) Repl main PWB, 2) Repl operation panel PWB.
1) Check harnass connections @ engine PWB, 2) Repl engine PWB, 3) Repl main PWB.
1) Repl expansion memory, 2) Repl main PWB.
1) Turn power Off/On to reset, 2) Repl PSU PWB.
1) Power Off/On.
1) Upgrade firmware above v.2.04A. (at this printing v.2.20C).
1) Reinstall fax sys M, 2) Reload firmware, 3)Repl fax sys M.
1) Reinstall fax sys M, 2) Reload firmware, 3)Repl fax sys M.
1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl HDD.
1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl HDD.
1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl HDD.
1) Power Off/On, 2) Reseat DIMM for operation panel, then reload firmware, 3) Repl DIMM for operation panel, then reload firmware.
1) Run U020, 2) Run U022, 3) Run U024.
1) Flash machine.
1) Repl main EEPROM then flash.
1) Repl main PWB.
1) Repl main PWB.
1) Replace engine PWB, 2) Repl main PWB.
1) Repl scanner PWB, 2) Repl main PWB.
1) Repl engine PWB.
1) Repl engine PWB.
1) Use KM-Net Viewer to update barcode files.
1) Power Off/On, 2) Reload firmware, 3) Repl Panel or main DIMM, 4) Reseat connectors to operation panel and main controller, 5) Repl operation panel PWB, 6) Repl main PWB. 7) May occur after HDD replacement. Power Off/On to reset.
1) Power Off/On, 2) Reseat & clean contacts of main DIMM & expansion memory, 3) Reload firmware, 4) Repl main DIMM or expansion memory, 5) Reseat connectors to operation panel and main controller, 6) Repl operation panel PWB, 7) Reformat or repl HDD.
1) Power Off/On, 2) Reseat & clean contacts of main DIMM, 3) Reload firmware, 4) Repl main DIMM, 5) Reseat connectors to operation panel and main controller, 6) Repl operation panel PWB, 7) Repl main PWB, 8) Reformat or repl HDD.
1) Repl main PWB, 2) Repl operation panel PWB.
1) Repl expansion memory, 2) Repl main PWB.
1) Repl flash ROM, 2) Repl engine PWB.
1) Repl flash ROM, 2) Repl engine PWB.
1) Repl main PWB.
1) Repl power source PWB.
Load paper.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check is the server is operating properly.
Set the number of pages to 999 or less.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct host name or IP address.
Check is the server is operating properly.
Check is the server is operating properly.
Set the number of pages to 999 or less.
Specify the destination address.
Select valid POP3 user other than [Other].
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operating properly.
Check is the server is operating properly.
Check is the server is operating properly.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Power Off/On.
Power Off/On.
Power Off/On.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Check the network connection (cable, network condition within LAN, etc.).
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Enter the correct host name or IP address.
Enter the correct username/password.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter correct folder path.
Specify the destination address.
Select valid POP3 user other than [Other].
Enter the correct host name or IP address.
Enter the correct port number.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check is the server is operating properly.
Power Off/On.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Set the number of pages to 999 or less.
Replace the toner container.
See above for details.
Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Load paper. If the same type of paper is loaded in another cassette in the same orientation, you can press either one of the paper select keys on the left of the touch panel to switch to the cassette for copying.
Load paper of the size and type indicated in the MP tray.
Leave the machine On and follow the instructions to replace the staple case. Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Document Box full: Press [End]. Repeat Copy Box full: Press [Continue] to copy without using Repeat Copy. Press [Cancel] to cancel job. See your key Operator/Administrator.
Close all covers securely.
Close the document processor.
Set the finisher correctly.
The job is cancelled. Press [End].
Press [End]. Then check: Registration of Authentication Server, Password & computer address of Authentication Server, Connection to the network. See your key Operator/Administrator.
Select another paper type. Press [Continue] to print without using duplex.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
Select another paper size. Press [Continue] to print without using offset.
Select another paper size/type. Press [Continue] to print without using punch.
Select another available paper size/type. Press [Continue] to print without stapling.
Clean the slit glass using the cleaning cloth supplied with the document processor.
Follow the instructions on the touch panel to empty the punch waste box.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
The job is cancelled. Press [End]. See your key Operator/Administrator.
Remove paper from the document finisher tray. If printing can be restarted, the touch panel display will prompt you to press Continue. Then press [Continue].
Remove paper from the folding tray.
Enter the correct user name or password.
Remove paper from the mailbox tray.
Format the memory card again.
1) Turn power Off/On.
Press [End].
01: Initialization Error. Initialize the HDD. 04: Insufficient space on the HDD to complete this operation. Move or delete data stored on the HDD to increase available space.
Cannot print any more. This job is canceled. Press [End]. See your Key Operator/Administrator.
Remove paper from the job separator tray. Printing resumes.
The job is cancelled. Press [End]. See your Key Operator/Administrator.
When inserting the memory card turn Off the main switch first.
Move or delete data stored on the memory card to increase available space.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Follow the displayed instructions to remove the jammed paper.
The job is paused. Press [Continue} to resume the job.
This job is cancelled. Press [End]. Remove or replace the removable memory.
Set the punch waste box correctly.
Set the waste toner box correctly.
Check the registered Account ID.
Put down the receiver.
Remove originals from the document processor, put them back in their original order, stack them uniformly and place them again. Press [Continue] to resume printing. Press [Cancel] to cancel the job.
Replace the waste toner box. Two are included in the box with each toner.
Remove originals from the document processor.
Press [Continue] to print, send, or store the scanned pages. The job cannot be processed completely. Press [Cancel] to cancel printing, sending, or storing.
1) Reseat lower connector DP to copier, 1) Repl main PWB.
Install the folding tray correctly to the 3,000 sheet finisher.
Install the folding unit correctly to the 3,000 sheet finisher.
Follow the displayed instructions to remove the jammed staple.
Follow the displayed instructions to remove the jammed staple.
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
The job is cancelled. Press [End].
Remove paper from the top exit tray, and press [Continue] to resume the job.
Remove output paper from the tray indicated on the panel. If tray B or C is full of paper press [Continue] to resume printing.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Model Error Code Description0xFBxx Undefined.
CS-420i, CS-520i C0030
CS-420i, CS-520i C0060 Main PWB Type Mismatch Error.
CS-420i, CS-520i C0070
CS-420i, CS-520i C0100
CS-420i, CS-520i C0120
CS-420i, CS-520i C0150
CS-420i, CS-520i C0160
CS-420i, CS-520i C0170
CS-420i, CS-520i C0180
CS-420i, CS-520i C0620
CS-420i, CS-520i C0630
CS-420i (2KR), CS-520i (2KS)
Fax Control PWB System Problem. Processing with fax software is disabled due to software or hardware issues.
Abnormal Detection Of Fax Control PWB Incompatability. Fax software is not compatible with main PWB software.
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
MAC Address Data Error. For data in which the MAC address is invalid.
Engine PWB EEPROM Backup Memory Device Problem. No response is issued from the device in reading/writing for 5ms or more, repeated five times successively. Mismatch of reading data from two locations occurs eight times successively. Mismatch between writing data and reading data occurs eight times successively.
Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
Fax Image DIMM Problem. DIMM is not installed correctly. DIMM cannot be accessed.
DMA transmission of image data does not complete within a specified period of time.
CS-420i, CS-520i C0640 Hard Disk Drive cannot be accessed.
CS-420i, CS-520i C0650
CS-420i, CS-520i C0800
CS-420i, CS-520i C0830
CS-420i, CS-520i C0840
CS-420i, CS-520i C0870
CS-420i, CS-520i C0920
CS-420i, CS-520i C1010
CS-420i, CS-520i C1020
Fax Image DIMM Check Problem. Improper DIMM or DIMM from another machine is installed.
Image processing problem. JAM05 is detected twice.
Fax Flash ROM program area checksum error. A checksum error occurred with the program of the fax control PWB.
Faults of RTC. The time is judged to go back based on the comparison of the RTC time and the current time, or five years or more have passed.
Fax Control PWB to Main PWB high capacity data transfer problem. High-capacity data transfer between the fax control PWB and the scanner MIP PWB was not normally performed after 10 retries.
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of the fax control PWB.
Cassette #1 Lift Motor error. Lift switch 1 does not turn On within 12 seconds of cassette insertion, detected four times successively.
Cassette #2 Lift Motor error. Lift switch 2 does not turn On within 12 seconds of cassette insertion, detected four times successively.
CS-420i, CS-520i C1030
CS-420i, CS-520i C1040
CS-420i, CS-520i C1100
CS-420i, CS-520i C1110
CS-420i, CS-520i C1120
CS-420i, CS-520i C1130
CS-420i, CS-520i C1800
CS-420i, CS-520i C1900
PF-720(B) optional cassette #3 lift motor error. PF lift switch 1 does not turn On within 12 seconds of cassette insertion, detected two times successively. After 1 second of lift motor drive, the lift overcurrent protective monitor signal is detected for 500ms or more, two times successively.
PF-720(B) optional cassette #4 lift motor error. PF lift switch 2 does not turn On within 12 seconds of cassette insertion, detected two times successively. After 1 second of lift motor drive, the lift overcurrent protective monitor signal is detected for 500ms or more, two times successively.
PF-760(B) (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.
PF-760(B) (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.
PF-760(B) (Left) Lift Motor 1 position problem. Level switch 1 remains off after 30 seconds of PF lift motor 1 operation.
PF-760(B) (Right) Lift Motor 2 position problem. Level switch 2 remains off after 30 seconds of PF lift motor 2 operation.
PF-720(B)/PF-760(B) Communication Problem. A communication error from the optional paper feeder is detected 10 times successively.
PF-720(B) EEPROM error. Write data & Read data are not in agreement three times consecutively.
CS-420i, CS-520i C2000
CS-420i, CS-520i C2250
CS-420i, CS-520i C2500
CS-420i, CS-520i C2600
CS-420i, CS-520i C2600
CS-420i, CS-520i C3100
CS-420i, CS-520i C3200
CS-420i, CS-520i C3210
Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation.
Main Charge Cleaning Motor Error. Lock error is detected three times in a row during a reciprocating cleaning motion.
Paper Feed Motor Error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation.
PF-720(B) Drive Motor Error. Lock signal exceeds 450ms.
PF-760(B) Paper Conveying Motor error. Lock signal exceeds 450ms.
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of illumination.
CIS Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of CIS illumination.
CS-420i, CS-520i C3300
CS-420i, CS-520i C3310
CS-420i, CS-520i C3500
CS-420i, CS-520i C3900
CS-420i, CS-520i C3910
CS-420i, CS-520i C4000
CS-420i, CS-520i C4010
CS-420i, CS-520i C4100
CS-420i, CS-520i C6000
CS-420i, CS-520i C6020
CS-420i, CS-520i C6030
Optical AGC Problem. After AGC correct input is not obtained at the CCD.
CIS AGC Problem. After AGC correct input is not obtained at the CIS.
Communication Error Between Scanner and SHD.
ISC PWB Backup Memory Read/Write Problem. Read & Write data does not match.
ISC PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.
BD Steady-State Problem. ASIC detects a Beam Detect error for 800ms sec after polygon motor stabilization, five times successively.
Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1 or 2 does not rise by at least 1C/1.8F for 5 sec.
Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more.
Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.
CS-420i, CS-520i C6040
CS-420i, CS-520i C6050
CS-420i, CS-520i C6400
CS-420i, CS-520i C6410
CS-420i, CS-520i C7300
CS-420i, CS-520i C7400
CS-420i, CS-520i C7410
CS-420i, CS-520i C7800
CS-420i, CS-520i C7810
CS-420i, CS-520i C7900
CS-420i, CS-520i C7910
CS-420i, CS-520i C8020
CS-420i, CS-520i C8030
Fixing Thermistor 1 Detection Error. Fuser thermistor 1 detected an abnormal value for 1 sec.
Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying.
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.
Toner Container Problem. Toner level is not detected when toner empty is detected.
Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.
Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.
Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.
PH-5A Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation.
DF-780(B) Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.
CS-420i, CS-520i C8040
CS-420i, CS-520i C8050
CS-420i, CS-520i C8060
CS-420i, CS-520i C8070
CS-420i, CS-520i C8140
CS-420i, CS-520i C8140
DF-780(B) Belt Problem. The belt sensor does not turn On/Off within the specified time of the belt solenoid turning On.
DF-760(B) Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
DF-760(B) Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 1.5 sec.
DF-760(B) Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
DF-760(B) Main Tray Problem. Main tray is not detected by main tray top limit detection sensor or main tray paper upper surface detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray paper upper surface detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray paper upper surface detection sensor remain on for 2 sec or more during main tray ascent.
DF-780(B) Tray Elevation Motor Problem. Tray lower limit sensor or paper surface sensor 1/2 cannot be detected within 10 seconds of tray motor activation.
CS-420i, CS-520i C8170
CS-420i, CS-520i C8170
CS-420i, CS-520i C8180
CS-420i, CS-520i C8180
CS-420i, CS-520i C8190
CS-420i, CS-520i C8210
CS-420i, CS-520i C8210
DF-760(B) Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
DF-720(B) Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
DF-760(B) Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
DF-720(B) Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
DF-720(B) Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
DF-760(B) Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
DF-720(B) Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.
CS-420i, CS-520i C8210
CS-420i, CS-520i C8220
CS-420i, CS-520i C8230
CS-420i, CS-520i C8300
CS-420i, CS-520i C8310
CS-420i, CS-520i C8320
CS-420i, CS-520i C8320
CS-420i, CS-520i C8330
CS-420i, CS-520i C8330
DF-780(B) Stapler Problem. Home position is not detected within a specific time of activation. Jam 82
DF-760(B) Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
DF-760(B) Stapler Motor Problem. Jam 82 is indicated.
BF-720 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
BF-720 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
BF-720 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
DF-780(B) Adjustment Motor 2 Problem. Adjustment sensor 2 does not turn On/Off within the specified time of adjustment motor 2 activation.
BF-720 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
DF-780(B) Adjustment Motor 1 Problem. Adjustment sensor 1 does not turn On/Off within the specified time of adjustment motor 1 activation.
CS-420i, CS-520i C8340
CS-420i, CS-520i C8350
CS-420i, CS-520i C8350
CS-420i, CS-520i C8360
CS-420i, CS-520i C8360
CS-420i, CS-520i C8440
CS-420i, CS-520i C8460
CS-420i, CS-520i C8500
CS-420i, CS-520i C8510
CS-420i, CS-520i C8800
CS-420i, CS-520i C8900
BF-720 Centerfold Staple Motor Problem. Jam 89.
BF-720 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
DF-780(B) Roller Motor Problem. Roller sensor does not turn On/Off within the specified time of the roller motor turning On.
BF-720 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
DF-780(B) Slide Motor Problem. The slide sensor does not turn On/Off within the specified time of the slide motor turning On.
DF-780(B) Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
DF-780(B) EEPROM Problem. Reading to or writing from EEPROM cannot be performed.
MT-720(B) Communication Error. The connection is detected, but communication is not possible with the mailbox.
MT-720(B) Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.
DF-760(B) Communication Problem. A communication error from the document finisher is detected (10) times in successively.
DF-760(B) Backup Memory Data Problem. Read and write data does not match three times successively.
CS-420i, CS-520i C8910
CS-420i, CS-520i C8920
CS-420i, CS-520i C8930
CS-420i, CS-520i C9000
CS-420i, CS-520i C9040
CS-420i, CS-520i C9050
CS-420i, CS-520i C9060
CS-420i, CS-520i C9070
CS-420i, CS-520i C9080
CS-420i, CS-520i C9500 no information available
CS-420i, CS-520i C9510 no information available
CS-420i, CS-520i C9520 no information available
CS-420i, CS-520i CF1xx no information availableCS-420i, CS-520i CF2xx no information availableCS-420i, CS-520i CF3xx no information availableCS-420i, CS-520i CF4xx no information availableCS-420i, CS-520i CF5xx no information availableCS-420i, CS-520i CF6xx no information availableCS-420i, CS-520i CF7xx no information availableCS-420i, CS-520i CFAxx no information available
PH-5A Backup Memory Data Problem. Read and write data does not match three times successively.
MT-720(B) Backup Memory Data Problem. Read and write data does not match.
BF-720 Backup Memory Data Problem. Read and write data does not match three times successively.
DP-750(B)/DP-760B Communication Problem. A communication error is detected.
DP-750(B)/DP-760(B) Lift Motor Ascention Error. The tray upper limit switch does not turn On within 2 sec of DP lift motor activation.
DP-750(B)/DP-760(B) Lift Motor Descent Error. The tray lower limit switch does not turn On within 2 sec of DP lift motor activation.
DP-750(B)/DP-760(B) EEPROM Error. Read and write data does not match. Data in the specified ara of the backup memory does not match the specified values.
DP-760(B) Communication Error Between DP & SHD. A communication error is detected.
DP-760(B) Communication Error Between DP & CIS. A communication error is detected.
CS-420i, CS-520i CFBxx no information availableCS-420i, CS-520i F000
CS-420i, CS-520i F040 Engine PWB Communication Error.
CS-420i, CS-520i F041 Scanner PWB Communication Error.
CS-420i, CS-520i F050 Engine ROM Checksum Error.CS-420i, CS-520i F090 Fax Control PWB Communication Error.
CS-420i, CS-520i F278
CS-420i, CS-520i E00000 or U00000
CS-420i, CS-520i E00100 or U00100
CS-420i, CS-520i E00200 or U00200
CS-420i, CS-520i E00300 or U00300
CS-420i, CS-520i E00430 or U00430
CS-420i, CS-520i E00430 or U00430
CS-420i, CS-520i E00431 or U00431
CS-420i, CS-520i E00432 or U00432
Operation Panel PWB Communication Error.
Power Supply In Drive System Error. Main switch was turned Off without using the power key, or a power failure has occurred.
Fax Communication Error: No response or line busy after the set number of redials.
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
Fax Communication Error: Recording paper on the destination unit has run out during reception.
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS-420i, CS-520i E00433 or U00433
CS-420i, CS-520i E00440 or U00440
CS-420i, CS-520i E00450 or U00450
CS-420i, CS-520i E00460 or U00460
CS-420i, CS-520i E00462 or U00462
CS-420i, CS-520i E00601 or U00601
CS-420i, CS-520i E00613 or U00613
CS-420i, CS-520i E00656 or U00656
CS-420i, CS-520i E00690 or U00690 Fax Communication Error: System error.
CS-420i, CS-520i E00700 or U00700
CS-420i, CS-520i E00800 or U00800
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
Fax Communication Error: Document jam or the document length exceeds the maximum.
Fax Communication Error: Image writing section problem.
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
CS-420i, CS-520i E00811 or U00811
CS-420i, CS-520i E00900 or U00900
CS-420i, CS-520i E00910 or U00910
CS-420i, CS-520i E01000 or U01000
CS-420i, CS-520i E01000 or U01000
CS-420i, CS-520i E01001 or U01001
CS-420i, CS-520i E01016 or U01016
CS-420i, CS-520i E01019 or U01019
Fax Communication Error: A page transmission error re-occurred after retry of transmission in ECM mode.
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-420i, CS-520i E01020 or U01020
CS-420i, CS-520i E01021 or U01021
CS-420i, CS-520i E01022 or U01022
CS-420i, CS-520i E01028 or U01028
CS-420i, CS-520i E01052 or U01052
CS-420i, CS-520i E01080 or U01080
CS-420i, CS-520i E01092 or U01092
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
CS-420i, CS-520i E01093 or U01093
CS-420i, CS-520i E01094 or U01094
CS-420i, CS-520i E01095 or U01095
CS-420i, CS-520i E01096 or U01096
CS-420i, CS-520i E01097 or U01097
CS-420i, CS-520i E01100 or U01100
CS-420i, CS-520i E01101 or U01101
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during phase B of transmission.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The preset number of command retransfers for DCS/NSS signals was exceeded during phase B of transmission.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS (Q) signal during phase D of transmission, and the preset number of command transfers was exceeded.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal or invalid command was received during phase D of transmission.
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The preset number of command retransfers was exceeded after transmission of an RR signal or no response.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
CS-420i, CS-520i E01102 or U01102
CS-420i, CS-520i E01110 or U01110
CS-420i, CS-520i E01111 or U01111
CS-420i, CS-520i E01113 or U01113
CS-420i, CS-520i E01125 or U01125
CS-420i, CS-520i E01129 or U01129
CS-420i, CS-520i E01141 or U01141
CS-420i, CS-520i E01143 or U01143
CS-420i, CS-520i E01155 or U01155
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
CS-420i, CS-520i E01160 or U01160
CS-420i, CS-520i E01162 or U01162
CS-420i, CS-520i E01191 or U01191
CS-420i, CS-520i E01193 or U01193
CS-420i, CS-520i E01194 or U01194
CS-420i, CS-520i E01195 or U01195
CS-420i, CS-520i E01196 or U01196
CS-420i, CS-520i E01400 or U01400
CS-420i, CS-520i E01500 or U01500
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. There was no response, or a DCN signal or invalid command was received during phase C/D of reception.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received during phase B of reception.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message was received during phase C of reception.
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Error line control was exceeded and a decoding error occurred for the message being received.
Fax Communication Error: An invalid one-touch key was specified during communication.
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS-420i, CS-520i E01600 or U01600
CS-420i, CS-520i E01700 or U01700
CS-420i, CS-520i E01720 or U01720
CS-420i, CS-520i E01721 or U01721
Fax Communication Error: A communication error occurred when called in V.8 mode.
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
CS-420i, CS-520i E01800 or U01800
CS-420i, CS-520i E01810 or U01810
CS-420i, CS-520i E01820 or U01820
CS-420i, CS-520i E01821 or U01821
CS-420i, CS-520i E03000 or U03000
CS-420i, CS-520i E03200 or U03200
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
Fax Communication Error: Operation was interrupted due to the absence of a common communication speed between units (including when an impossible combination of communication speed and symbol speed occurs), during reception in V.34 mode. After MPh exchange, a DCN signal was transmitted to the destination unit and the line was cut.
Fax Communication Error: No document was present in the destination unit when polling reception started.
Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.
CS-420i, CS-520i E03300 or U03300
CS-420i, CS-520i E03300 or U03300
CS-420i, CS-520i E03400 or U03400
CS-420i, CS-520i E03500 or U03500
CS-420i, CS-520i E03600 or U03600
CS-420i, CS-520i E03700 or U03700
CS-420i, CS-520i E04000 or U04000
CS-420i, CS-520i E04100 or U04100
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.
CS-420i, CS-520i E04200 or U04200
CS-420i, CS-520i E04300 or U04300
CS-420i, CS-520i E04400 or U04400
CS-420i, CS-520i E04500 or U04500
CS-420i, CS-520i E05100 or U05100
CS-420i, CS-520i E05200 or U05200
CS-420i, CS-520i E05300 or U05300
CS-420i, CS-520i E14000 or U14000
CS-420i, CS-520i E14000 or U14000
CS-420i, CS-520i E14100 or U14100
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
Fax Communication Error: Memory overflowed during confidential reception.
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
CS-420i, CS-520i E19000 or U19000
CS-420i, CS-520i E19100 or U19100
CS-420i, CS-520i E19300 or U19300
CS-420i, CS-520i Send SMB Error 1102
CS-420i, CS-520i Send SMB Error 1102
CS-420i, CS-520i Send SMB Error 1102
CS-420i, CS-520i Send SMB Error 1102
CS-420i, CS-520i Send SMB Error 1102
CS-420i, CS-520i Send SMB Error 1103
CS-420i, CS-520i Send SMB Error 1103
CS-420i, CS-520i Send SMB Error 1103
CS-420i, CS-520i Send SMB Error 1105
CS-420i, CS-520i Send SMB Error 2101
CS-420i, CS-520i Send SMB Error 2101
CS-420i, CS-520i Send SMB Error 2101
Fax Communication Error: Memory overflowed during memory reception.
Fax Communication Error: Memory overflowed in the destination unit during transmission.
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Error: Username/Password or Shared Name/Folder Name. Host name error.
Error: Pathname or File Name. Domain name is not entered.
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Error: Pathname or File Name. Assign disable folder path.
Error: Not Supported Protocol. SMB protocol is set to OFF.
Error: Can Not Connect. Enter the disable host name/IP address.
Error: Can Not Connect. Assign the wrong port number.
Error: Can Not Connect. Network is not connected.
CS-420i, CS-520i Send SMB Error 2103
CS-420i, CS-520i Send SMB Error 2201
CS-420i, CS-520i Send SMB Error 2203
CS-420i, CS-520i Send SMB Error 9181
CS-420i, CS-520i Send FTP Error 1101
CS-420i, CS-520i Send FTP Error 1102
CS-420i, CS-520i Send FTP Error 1102
CS-420i, CS-520i Send FTP Error 1103
CS-420i, CS-520i Send FTP Error 1103
CS-420i, CS-520i Send FTP Error 1105
CS-420i, CS-520i Send FTP Error 2101
CS-420i, CS-520i Send FTP Error 2101
CS-420i, CS-520i Send FTP Error 2101
CS-420i, CS-520i Send FTP Error 2102
CS-420i, CS-520i Send FTP Error 2102
CS-420i, CS-520i Send FTP Error 2103
Error: Response Wait With Timeout. The server is unable to communicate.
Error: Network Transfer. Error occurs on the network.
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Error: Host Name. Enter the disable host name/IP address.
Error: Username/Password. Domain name is not entered.
Error: Username/Password. Assign disable user/password.
Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Error: Pathname or File Name. Assign disable folder path.
Error: Not Supported Protocol. FTP protocol is set to OFF.
Error: Can Not Connect. Enter the disable host name/IP address.
Error: Can Not Connect. Assign the wrong port number.
Error: Can Not Connect. Network is not connected.
Error: Cannot Connect With Timeout. The server is unable to communicate.
Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Error: Response Wait With Timeout. The server is unable to communicate.
CS-420i, CS-520i Send FTP Error 2201
CS-420i, CS-520i Send FTP Error 2202
CS-420i, CS-520i Send FTP Error 2203
CS-420i, CS-520i Send FTP Error 3101
CS-420i, CS-520i Send FTP Error 9181
CS-420i, CS-520i Send email Error 1101
CS-420i, CS-520i Send email Error 1102
CS-420i, CS-520i Send email Error 1104
CS-420i, CS-520i Send email Error 1105
CS-420i, CS-520i Send email Error 1106
CS-420i, CS-520i Send email Error 2101
CS-420i, CS-520i Send email Error 2101
CS-420i, CS-520i Send email Error 2101
CS-420i, CS-520i Send email Error 2102
CS-420i, CS-520i Send email Error 2103
Error: Network Transfer. Error occurs on the network.
Error: Network Transfer With Timeout. Error occurs on the network.
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Error: Server Response. The server is error status.
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Error: Host Name. SMTP server name is not set. Error SMTP server name.
Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Error: No Recipient Address. The destination address is not specified.
Error: Not Supported Protocol. SMTP protocol is set to OFF.
Error: No Sender Info. Sender address is not entered.
Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Error: Can Not Connect. The specified server is not SMTP server.
Error: Can Not Connect. Network is not connected.
Error: Cannot Connect With Timeout. The server is unable to communicate.
Error: Response Wait With Timeout. The server is unable to communicate.
CS-420i, CS-520i Send email Error 2201
CS-420i, CS-520i Send email Error 2202
CS-420i, CS-520i Send email Error 2203
CS-420i, CS-520i Send email Error 2204
CS-420i, CS-520i Send email Error 3101
CS-420i, CS-520i Send email Error 3101
CS-420i, CS-520i Send email Error 3201
CS-420i, CS-520i Send email Error 9181
CS-420i, CS-520i TWAIN Error 2202
CS-420i, CS-520i TWAIN Error 9181
CS-420i, CS-520i Software Error 5101
CS-420i, CS-520i Software Error 5102
CS-420i, CS-520i Software Error 5103
CS-420i, CS-520i Software Error 5104
CS-420i, CS-520i Software Error 7101
Error: Network Transfer. Error occurs on the network.
Error: Network Transfer With Timeout. Error occurs on the network.
Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Error: Email Size Limit. The size of the email attachment exceeds its limit.
Error: Server Response. The server is error status.
Error: Server Response. Server setting is not authenticated normally.
Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Error: Not Yet Opened. Error for storage status in the operation handle.
Error: Already Opened. Error for storage status in the operation handle.
Error: Memory Allocation. Insufficient memory space.
CS-420i, CS-520i Software Error 7102
CS-420i, CS-520i Software Error 720f
CS-420i, CS-520i Send error. 1101
CS-420i, CS-520i Send error. 1101
CS-420i, CS-520i Send error. 1101
CS-420i, CS-520i Send error. 1102
CS-420i, CS-520i Send error. 1102
CS-420i, CS-520i Send error. 1102
CS-420i, CS-520i Send error. 1102
CS-420i, CS-520i Send error. 1102
CS-420i, CS-520i Send error. 1103
CS-420i, CS-520i Send error. 1103
Error: Socket Create. Unable to create a communication socket.
Error: Unknown Error. Unable to determine the cause.
Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name. Fails to send iFax.
Send FTP Error: Host Name. Enter the disable host name/IP address.
Send SMB Error: Host Name. Enter the disable host name/IP address.
Send Email Error/ Send iFax Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
CS-420i, CS-520i Send error. 1103
CS-420i, CS-520i Send error. 1104
CS-420i, CS-520i Send error. 1105
CS-420i, CS-520i Send error. 1105
CS-420i, CS-520i Send error. 1105
CS-420i, CS-520i Send error. 1106
CS-420i, CS-520i Send error. 1131
CS-420i, CS-520i Send error. 1132
CS-420i, CS-520i Send error. 2101
CS-420i, CS-520i Send error. 2101
CS-420i, CS-520i Send error. 2101
CS-420i, CS-520i Send error. 2101
Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
Send Email Error/ Send iFax Error: No Recipient Address. The destination address is not specified.
Send Email Error/ Send iFax Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
Send Email Error/ Send iFax Error: No Sender Info. Sender address is not entered.
Send FTP Error: Secure protocol settings are OFF in Command Center.
Send FTP Error: Is FTPS available? Is encryption available?
Send Email Error/ Send iFax Error: Can Not Connect. Network is not connected.
Send Email Error/ Send iFax Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send Email Error/ Send iFax Error: Can Not Connect. The specified server is not SMTP server.
Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
CS-420i, CS-520i Send error. 2101
CS-420i, CS-520i Send error. 2101
CS-420i, CS-520i Send error. 2102
CS-420i, CS-520i Send error. 2102
CS-420i, CS-520i Send error. 2103
CS-420i, CS-520i Send error. 2201
CS-420i, CS-520i Send error. 2202
CS-420i, CS-520i Send error. 2202
CS-420i, CS-520i Send error. 2203
CS-420i, CS-520i Send error. 2204
CS-420i, CS-520i Send error. 2231 Send FTP Error: Failed to send via FTP.
CS-420i, CS-520i
Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
Send SMB/FTP Error: Can Not Connect. Network is not connected.
Send Email/ iFax/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send Email/ iFax/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
Send Email/ iFax/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
Send Email/ iFax/ FTP Error: Network Transfer With Timeout. Error occurs on the network.
Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
Send Email/ iFax/ FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send Email/ iFax Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send error. Job is cancelled. Press [End].
3101
Send Email/FTP Error: Server Response. The server is error status.
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i Is the acceptable staple count exceeded?
CS-420i, CS-520i "Add paper in cassette #." Is the indicated cassette out of paper?
CS-420i, CS-520i
CS-420i, CS-520i "Add staples."
CS-420i, CS-520i "Add toner."CS-420i, CS-520i "Box is not found."
CS-420i, CS-520i "Box Limit Exceeded."
CS-420i, CS-520i
CS-420i, CS-520i
Send error. Job is cancelled. Press [End].
3101
Send Email Error: Server Response. Server setting is not authenticated normally.
Send error. Job is cancelled. Press [End].
3201
Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send error. Job is cancelled. Press [End].
9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
"Acceptable staple count exceeded."
"Add paper in Multi Purpose tray."
Is the paper of the specified size loaded in the multipurpose tray?
Has the document finisher run out of staples?
This job is cancelled because the specified box cannot be found.
Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
"Cannot connect to Authentication Server."
"Cannot duplex print on this paper."
Did you select a paper size/type that cannot be duplex printed?
CS-420i, CS-520i "Cannot offset this paper."
CS-420i, CS-520i
CS-420i, CS-520i "Cannot staple this paper."
CS-420i, CS-520i "Check the cover."
CS-420i, CS-520i
CS-420i, CS-520i "Check the finisher." Is the document finisher set correctly?"
CS-420i, CS-520i "Clean the slit glass." Dirt has been identified on the slit glass.
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i "Fax box limit exceeded."
CS-420i, CS-520i
CS-420i, CS-520i An error has occurred on the hard disk.
CS-420i, CS-520i "Incorrect Account ID." The account ID# does not match.
CS-420i, CS-520i "Incorrect box password."
CS-420i, CS-520i
Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
"Cannot staple at the specified position."
Have you selected a poisition that cannot be stapled?
Did you select a paper size/type that cannot be stapled?
Are any covers open? Does the message indicate which cover is open?
"Check the document processor."
Is the document processor open? Is the top cover of the document processor open?
"Confidential document is detected."
The machine detects the documents guard pattern on the original document.
"Failed to specify Job Accounting."
Job accounting is not specified in the print driver.
"Failed to store job retention data."
Fax box is full, and no further storage is available.
"Finisher tray is full of paper."
Is the acceptable storage capacity exceeded for the document finisher tray?"
"Hard Disk error. Job is cancelled. Press [End] ##"
"Incorrect Login User Name or Password."
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i "KPDL error." A PostScript error has occurred.
CS-420i, CS-520i "Machine failure."
CS-420i, CS-520i
CS-420i, CS-520i "Memory is full."
CS-420i, CS-520i "Paper Jam. ###"
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i The waste toner box is full.
CS-420i, CS-520i "Scanner memory is full."
CS-420i, CS-520i "Send Error. ####"
CS-420i, CS-520i "Set the waste toner box."
"Job Accounting restriction exceeded."
The print count exceeded the acceptable count restricted by Job Accounting.
"Job Separator is full of paper."
Is the maximum capacity of the job separator tray exceeded?
An internal error has occurred. Make a note of the error code number displayed on the panel. See above.
"Maximum number of scanned pages."
Is the acceptable scanning count exceeded?
Unable to continue the job, as the memory is used up."
Make a note of the jam location number displayed on the panel. Leave the machine On.
"Removable memory error."
An error has occurred on the USB stick memory or Compact Flash memory.
"Remove all originals in the document processor."
Are there any originals left in the document processor?
"Replace all originals and press [Continue]."
"Replace the waste toner box."
Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
An error has occurred during transmission.
The waste toner box is not installed correctly.
CS-420i, CS-520i "Staple jam."
CS-420i, CS-520i "System Error."
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i The specified file is not found.
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i
CS-420i, CS-520i "Warning low memory."
The location of the jam will be indicated on the panel. Leave the machine On.
A system error has occurred. Confirm that the Attention indicator is lighting.
"The phone receiver is off the hook."
"The removable memory is not formatted."
Is the removable memory formatted by this machine?
"The source file is not found."
"Top tray of the machine is full of paper."
The exit tray at the top of the machine is full.
"Unknown Toner Installed."
Is the toner cartridge taken from another machine of the same model while it was displaying the "Add Toner." message?
"Unknown Toner Installed. PC"
Is a differently named or counterfeit toner product installed?
Further scanning cannot be performed due to insufficient memory.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
10871087 935
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Mode:1 > Start > turn main switch Off/On.
24
Turn power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
First try turning power Off/On. If code immediately returns format hard drive: 10871087
Start > Execute > Start (tech only)
First try turning power Off/On. If code immediately returns reload fax firmware.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
Turn power Off/On.
Turn power Off/On.
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
Start > Execute > Start > power Off/On.
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Turn power Off/On.Turn power Off/On.Turn power Off/On.Turn power Off/On.Turn power Off/On.Turn power Off/On.Turn power Off/On.Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Power Off/On.
Turn power Off/On.
Service Checks
1) Repl fax card.
1) Repl main PWB.
1) Temporarity run simulation 935: 10871087 > 935 > Start > Mode:1 > Start. Repl relay PWB. When replaced reset U935 to Mode:0.
1) Install current fax firmware, 2) Install compatible fax card (Fax Sys S).
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB, 4) Repl main PWB.
1) Contact Kyocera Service Administrative Division, 2) Repl engine PWB, 3) Repl main PWB.
1) Reinstall fax image DIMM, 2) Repl fax image DIMM, 3) Repl main PWB.
1) Reseat connectors DP to copier, 2) Repl main PWB.
1) Repl main PWB.
1) Reload firmware, 2) Repl fax card.
1) Power Off/On 2) Repl fax card.
1) Power Off/On 2) Reseat YC49 @ main PCB, 3) Reformat HDD, 4) Repl main PWB
1) Reinstall fax image DIMM, 2) Run simulation U671 (recovery fax DIMM), 3) Repl fax image DIMM, 4) Repl main PWB.
1) Reconnect battery at main PWB. 2) Replace main PWB.
1) Reseat connectors to fax card, interface PWB, and main PWB, 2) Repl fax card, 3) Repl main PWB.
1) Check for lift drive problem 2) Reseat YC8 @ engine PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC8-B9 @ engine PWB goes low when upper lift switch is OFF. If no, replace upper lift switch, 5) Repl engine PWB.
1) Check for lift drive problem 2) Reseat YC8 @ engine PWB, 3) Check for open motor coil. Repl lift motor, 4) Check YC8-B15 @ engine PWB goes low when lower lift switch is OFF. If no, replace lower lift switch, 5) Repl engine PWB.
1) Check for lift drive problem, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-7 @ PF main PWB goes low when PF lift switch 1 is OFF. If no, replace PF lift switch 1.
1) Check for lift drive problem, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-9 @ PF main PWB goes low when PF lift switch 2 is OFF. If no, replace PF lift switch 2.
1) Check for lift drive problem, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB.
1) Check for lift drive problem, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB.
1) Check for lift drive problems, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Check YC5-4 @ PF Main PWB goes low when level switch 1 is OFF. If no, repl level switch 1. 5) Repl lift motor.
1) Check for lift drive problems, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Check YC5-7 @ PF Main PWB goes low when level switch 2 is OFF. If no, repl level switch 2. 5) Repl lift motor.
1) Reseat connectors on PF main PWB and YC15 @ engine PWB, 2) Pinout harnass, 3) Repl engine PWB, 4) Repl PF main PWB.
1) Reseat connectors on PF main PWB and YC15 @ engine PWB, 2) Pinout harnass, 3) Repl engine PWB, 4) Repl PF main PWB.
1) Check for drive problems, 2) Reseat YC11 @ engine PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ engine PWB, 3) Pinout harnass, 4) Repl main charge cleaning motor, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC11 @ engine PWB, 3) Pinout harnass, 4) Repl paper feed motor, 5) Repl engine PWB .
1) Check for drive problems, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Repl PF drive motor, 5) Repl PF main PWB, 6) Repl engine PWB.
1) Check for drive problems, 2) Reseat connectors on PF main PWB and YC15 @ engine PWB, 3) Pinout harnass, 4) Repl paper conveying motor, 5) Repl PF main PWB. 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7, YC8 @ ISM PWB (scanner PWB), 3) Reseat connector on scanner home position switch & scanner motor, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl ISC PWB (shading PWB), 7) Repl ISM PWB (scanner PWB).
1) Reseat YC5 @ ISM PWB (scanner PWB), 2) Reseat conn @ inverter PWB, 3) Pinout harnass, 4) Adj position of shading plate, 5) Repl home position switch, 6) Repl lamp & inverter PWB, 7) Repl ISM PWB (scanner PWB), 8) Replace ISC PWB (shading PWB), 9) CCD PWB.
1) Reseat conn @ ISM PWB & DP driver PWB, 2) Pinout harnass, 3) Replace DP inverter PWB, 4) Repl CIS, 5) Repl DP driver PWB.
1) Reseat YC5 @ ISM PWB & inverter PWB, 2) Pinout harnass, 3) Repl lamp & inverter PWB, 4) Repl ISM PWB (scanner PWB), 5) Repl ISC PWB (shading PWB), 6) Repl CCD PWB.
1) Repl DP inverter PWB, 2) Repl CIS, 3) Repl DP driver PWB.
1) Reseat YC2 @ CCD PWB & YC2 @ ISC PWB, 2) Pinout harnass, 3) Repl ISC PWB (shading PWB), 4) Repl CCD PWB.
1) Repl ISM PWB (scanner PWB), 2) Repl ISC PWB (shading PWB).
1) Repl ISM PWB (scanner PWB), 2) Repl ISC PWB (shading PWB).
1) Reseat YC3 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Reseat YC3 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Reseat YC3 @ engine PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl engine PWB.
1) Check that thermistor1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters, 4) Repl PSU, 5) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1 or 2, 3) Repl engine PWB.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1 or 2, 3) Repl engine PWB.
1) Reinsert fuser unit, 2) Repl fuser unit.
1) Reinsert drum unit, 2) Repl drum unit.
1) Pinout harnass, 2) Repl drum unit.
1) Pinout harnass, 2) Repl developing unit.
1) Check that thermistors are contacting fuser rollers and clean, 2) Replace thermistor 1, 3) Repl engine PWB.
1) Check that thermistor 1 is contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters 4) Repl PSU, 5) Repl engine PWB.
1) Check wall outlet ground to neutral voltage. 2) Repl PSU, 3) Repl engine PWB.
1) Check YC5 @ engine PWB, 2) Pinout harnass, 3) Replace toner container sensor.
1) Reinsert developing unit, 2) Repl developing unit.
1) Reseat YC10 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Reseat YC14 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Check punch PWB connectors, 2) Pinout harnass, 3) Repl punch motor, 4) Repl punch PWB, 5) Repl finisher PWB.
1) Reseat connectors @ tray upper limit sensor, paper surface sensor 1/2, 2) Pinout harnass, 3) Repl tray upper limit sensor, paper surface sensor 1/2, 4) Repl finisher main PWB.
1) Reseat connectors @ belt sensor, belt solenoid, 2) Pinout harnass, 3) Repl belt sensor, 4) Repl belt solenoid, 5) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & paper conveying belt motor 1 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS1, 4) Repl paper conveying belt motor 1, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC6 @ internal tray PWB & paper conveying belt motor 2 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS2, 4) Repl paper conveying belt motor 2, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC1, YC4 @ internal tray PWB & YC6, YC24 @ finisher main PWB, 2) Pinout harnass, 3) Repl internal tray PWB, 4) Repl finisher main PWB.
1) Reseat YC11 @ finisher main PWB & connector for main tray motor, 2) Pinout harnass, 3) Replace main tray upper & lower limit detection switches & main tray paper upper surface detection sensor, 4) Repl main tray motor, 5) Repl finisher main PWB.
1) Reseat connectors or Replace tray lower limit sensor, paper surface sensor 1/2, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & side registration motor 1 connector, 2) Pinout harnass, 3) Repl side registration motor 1, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat front registration HPS, 2) Reseat front registration motor connector, 3) Repl front registration HPS, 4) Replace front registration motor, 5) Repl finisher main PWB.
1) Reseat YC8 @ internal tray PWB & side registration motor 2 connector, 2) Pinout harnass, 3) Repl side registration motor 2, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat rear registration HPS connector, 2) Reseat rear registration motor connector, 3) Repl rear registration HPS, 4) Replace rear registration motor, 5) Repl finisher main PWB.
1) Reseat trailing edge registration HPS connector, 2) Reseat trailing edge registration motor connector, 3) Repl trailing edge registration HPS, 4) Replace trailing edge registration motor, 5) Repl finisher main PWB.
1) Reseat YC9 @ finisher main PWB & stapler moving motor 1 connector, 2) Repl stapler moving motor 1, 3) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl front stapler assy, 4) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl stapler assy, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler moving motor 2 connector & staple relay PWB, 2) Replace stapler moving motor 2, 3) Repl staple relay PWB, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler motor connector & staple relay PWB, 2) Replace stapler motor, 3) Replace staple relay PWB, 4) Repl finisher main PWB.
1) Reseat YC5, YC20 @ finisher main PWB, 2) Reseat YC1, YC2 @ centerfold main PWB, 2) Replace centerfold unit set switch, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC6 @ centerfold main PWB & centerfold side registration motor 2 connector, 2) Repl centerfold side registration motor 2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC6 & YC7 @ centerfold main PWB & centerfold paper conveying motor belt 1/2 connector, 2) Repl centerfold paper conveying belt motor 1/2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors adjustment sensor 2 & adjustment motor 2, 2) Repl adjustment sensor 2, 3) Repl adjustment motor 2, 4) Repl finisher main PWB.
1) Reseat YC8 @ centerfold main PWB & blade motor connector, 2) Repl blade motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors adjustment sensor 1 & adjustment motor 1, 2) Repl adjustment sensor 1, 3) Repl adjustment motor 1, 4) Repl finisher main PWB.
1) Repl finisher main PWB.
1) Reseat YC9 @ centerfold main PWB & centerfold staple motor connector, 2) Repl centerfold staple motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC7 @ centerfold main PWB & centerfold side registration motor 1 connector, 2) Repl centerfold side registration motor 1, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors roller motor sensor & roller motor, 2) Repl roller motor sensor, 3) Repl roller motor, 4) Repl finisher main PWB.
1) Reseat YC12 @ centerfold main PWB & centerfold main motor connector, 2) Repl centerfold main motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors slide motor sensor & slide motor, 2) Repl slide motor sensor, 3) Repl slide motor, 4) Repl finisher main PWB.
1) Reseat paper entry sensor connector, 2) Clean foreign matter from paper entry sensor, 3) Repl paper entry sensor, 4) Repl finisher main PWB.
1) Reseat YC7 @ finisher main PWB & connections to the mailbox, 2) Repl mailbox main PWB, 3) Repl finisher main PWB.
1) Reseat YC5 @ mailbox main PWB & mailbox drive motor connector, 2) Repl mailbox drive motor, 3) Repl mailbox main PWB, 4) Repl finisher main PWB.
1) Reeat all connectors @ engine PWB & finisher main PWB. 2) Repl finisher main PWB, 3) Repl engine PWB.
1) Reseat all connectors @ engine PWB & finisher main PWB. 2) Reseat EEPROM, 3) Repl finisher main PWB.
1) Reseat connectors @ CIS, 2) Repl CIS.
1) Reseat all connectors @ punch PWB & YC4 @ finisher main PWB. 2) Repl punch PWB.
1) Reseat all connectors @ mailbox PWB & YC7 @ finisher main PWB. 2) Repl mailbox main PWB.
1) Reseat all connectors @ centerfold main PWB & YC5 @ finisher main PWB. 2) Reseat EEPROM, 3) Repl centerfold main PWB.
1) Reseat YC6 @ ISM PWB (scanner PWB) & the pigtail to the copier, 2) Repl DP driver PWB, 3) Repl ISM PWB (scanner PWB).
1) Reseat upper limit switch & lift motor connectors, 2) Repl upper limit switch, 3) Repl lift motor, 4) Repl DP driver PWB.
1) Reseat lower limit switch & lift motor connectors, 2) Repl lower limit switch, 3) Repl lift motor, 4) Repl DP driver PWB.
1) Reseat connectors @ DP driver PWB, 2) Repl DP driver PWB.
1) Reseat connectors @ SHD PWB, 2) Repl SHD PWB.
1) Contact Kyocera Service Administrative Division.
1) Contact Kyocera Service Administrative Division.
1) Contact Kyocera Service Administrative Division.
1) Replace engine PWB, 2) Repl main PWB.
1) Repl engine PWB.1) Repl main PWB.
Load paper.
1) Repl main PWB, 2) Repl operation panel PWB.
1) Repl ISM PWB (scanner PWB), 2) Repl main PWB.
1) To switch Off power: first press the power keyswitch until the main power indicator goes Off, then turn the main power switch Off.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter correct folder path.
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Enter the user name with the form of either [DomainYUser] or [Domain/User].
Enter the correct username/password. Check the access limit of destination folder.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Specify the destination address.
Select valid POP3 user other than [Other].
Check if the server is operating properly.
Check is the server is operating properly.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Set the number of pages to 999 or less.
Set the number of pages to 999 or less.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Check the network connection (cable, network condition within LAN, etc.).
Power Off/On.
Power Off/On.
Enter the correct host name or IP address.
Enter the correct host name or IP address.
Enter the correct username/password.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Enter correct folder path.
Specify the destination address.
Select valid POP3 user other than [Other].
Enter the correct host name or IP address.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Set secure protocol settings to ON in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check is the server is operating properly.
Check is the server is operating properly.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the network connection (cable, network condition within LAN, etc.).
Set the number of pages to 999 or less.
Replace the toner container.Press [End].
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Load paper. If the same type of paper is loaded in another cassette in the same orientation, you can press either one of the paper select keys on the left of the touch panel to switch to the cassette for copying.
Load paper of the size and type indicated in the MP tray.
Leave the machine On and follow the instructions to replace the staple case. Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Document Box full: Press [End]. Repeat Copy Box full: Press [Continue] to copy without using Repeat Copy. Press [Cancel] to cancel job. See your key Operator/Administrator.
Press [End]. Then check: Registration of Authentication Server, Password & computer address of Authentication Server, Connection to the network. See your key Operator/Administrator.
Select another paper type. Press [Continue] to print without using duplex.
Close all covers securely.
Close the document processor.
Set the finisher correctly.
The job is cancelled. Press [End].
Check the registered Account ID.
Enter the correct password.
Enter the correct user name or password.
Select another paper size. Press [Continue] to print without using offset.
Select a position that can be stapled. Press [Continue] to print without stapling.
Select another available paper size/type. Press [Continue] to print without stapling.
Clean the slit glass using the cleaning cloth supplied with the document processor.
The scanned document is printed blank or sending of the document is cancelled.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
The job is cancelled. Press [End]. Delete some data from the specified fax box. See your key Operator/Administrator.
Remove paper from the document finisher tray. If printing can be restarted, the touch panel display will prompt you to press Continue. Then press [Continue].
01: Initialization Error. Initialize the HDD. 04: Insufficient space on the HDD to complete this operation. Move or delete data stored on the HDD to increase available space.
See above for details.
See above for details.
Set the waste toner box correctly.
Cannot print any more. This job is canceled. Press [End]. See your Key Operator/Administrator.
Remove paper from the job separator tray. Printing resumes.
The job is cancelled. Press [End]. See your Key Operator/Administrator.
Only one copy of the scanned pages is available. Press [Continue] to print, send, or store the scanned pages. Press [Cancel] to cancel printing, sending, or storing.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Follow the displayed instructions to remove the jammed paper.
This job is cancelled. Press [End]. Remove or replace the removable memory.
Remove originals from the document processor.
Remove originals from the document processor, put them back in their original order, stack them uniformly and place them again. Press [Continue] to resume printing. Press [Cancel] to cancel the job.
Replace the waste toner box. Two are included in the box with each toner.
Press [Continue] to print, send, or store the scanned pages. The job cannot be processed completely. Press [Cancel] to cancel printing, sending, or storing.
Put down the receiver.
The job is cancelled. Press [End].
Ignore the message and use the toner.
Follow the displayed instructions to remove the jammed staple.
Make note of the error code number. Turn power Off/On.
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
Remove paper from the top exit tray, and press [Continue] to resume the job.
Install our genuine product that is specified for this machine.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Model Error Code DescriptionC0060 Main PWB Type Mismatch Error.
CS-6030, CS-8030 C0100
CS-6030, CS-8030 C0110
CS-6030, CS-8030 C0130
CS-6030, CS-8030 C0140
CS-6030, CS-8030 C0150
CS-6030, CS-8030 C0160
CS-6030, CS-8030 C0170
CS-6030, CS-8030 C0180
CS-6030, CS-8030 C0210
CS-6030, CS-8030 C0220
CS-6030, CS-8030 C0240
CS-6030 (2FC), CS-8030 (2FB)
Backup Memory Read/Write Problem. Read and write data does not match.
Main PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match specified values.
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
Engine PWB EEPROM Backup Memory Data Problem. Data for backup data check is changed at the check after startup.
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
CPU Communication Problem. Synchronization cannot be taken between the main CPU and engine CPU.
CPU Communication Problem. Synchronization cannot be taken between the main CPU and scanner CPU.
Printer Board Communication Problem. Printer board does not respond within 120 sec after power ON.
CS-6030, CS-8030 C0250
CS-6030, CS-8030 C0330 Relay Board Communication Problem.
CS-6030, CS-8030 C0410
CS-6030, CS-8030 C0420
CS-6030, CS-8030 C0440
CS-6030, CS-8030 C0460
CS-6030, CS-8030 C0500
CS-6030, CS-8030 C0510
CS-6030, CS-8030 C0610
CS-6030, CS-8030 C0630
Network Scanner Board Communication Problem. Network scanner board does not respond to the alive command three times within 30 sec. Network scanner board does not respond to the communication command within 75 sec.
DP Communication Problem. There is no reply after 5 tries at communication. A communication error has occurred.
PF-650/PF-660 Communication Error. During initial rotations there is no reply after 40 tries at communication. During normal operation there is no reply after 5 tries at communication.
DF-650 Communication Problem. A communication error from document finisher is detected 10 times in succession.
Duplex Unit Communication Problem. A communication error frum duplex section is detected 10 times in succession.
Paper Feed Unit Communication Error. A communication error is detected 10 times in succession from cassettes 1 & 2.
Paper Feed Unit Communication Error. A communication error is detected 10 times in succession from cassettes 3 & 4.
Bitmap Problem. The DIMM on the scanner Main PWB does not operate correctly.
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-6030, CS-8030 C0640 Hard Disk Drive cannot be accessed.
CS-6030, CS-8030 C0700
CS-6030, CS-8030 C0750
CS-6030, CS-8030 C0960 Developing Unit EEPROM Error.
CS-6030, CS-8030 C0970 Cleaning Unit EEPROM Error.
CS-6030, CS-8030 C1010
CS-6030, CS-8030 C1020
CS-6030, CS-8030 C1030
PF-650/PF-660 EEPROM Error. An error occurs in EEPROM (U4) data read or write for the side feeder main PWB.
DF-650 EEPROM Error. A backup memory error is received in serial communication data from the finisher.
Cassette #1 Lift Motor error. When cassette is inserted lift upper limit switch 1 does not turn ON within 33 sec of lift motor 1 activation. During copying lift upper limit switch 1 does not turn on within 1 sec of lift motor 1 activation.
Cassette #2 Lift Motor error. When cassette is inserted lift upper limit switch 2 does not turn ON within 33 sec of lift motor 2 activation. During copying lift upper limit switch 2 does not turn on within 1 sec of lift motor 2 activation.
Cassette #3 Lift Motor error. When cassette is inserted lift upper limit switch 3 does not turn ON within 33 sec of lift motor 3 activation. During copying lift upper limit switch 3 does not turn on within 1 sec of lift motor 3 activation.
CS-6030, CS-8030 C1040
CS-6030, CS-8030 C1140
CS-6030, CS-8030 C1140
CS-6030, CS-8030 C1150
Cassette #4 Lift Motor error. When cassette is inserted lift upper limit switch 4 does not turn ON within 33 sec of lift motor 4 activation. During copying lift upper limit switch 4 does not turn on within 1 sec of lift motor 4 activation.
PF-650 Lift Motor Ascention Error. During initialization or door open upper limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation. During paper feed upper limit detection switch does not turn OFF within 200ms.
PF-660 Lift Motor Ascention Error. During initialization or door open upper limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation. During paper feed upper limit detection switch does not turn OFF within 200ms.
PF-650 Lift Motor Descent Error. During initialization or door open lower limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation. During paper feed lower limit detection switch does not turn OFF withing 200ms.
CS-6030, CS-8030 C1150
CS-6030, CS-8030 C1200
CS-6030, CS-8030 C2100
CS-6030, CS-8030 C2200
CS-6030, CS-8030 C2300
CS-6030, CS-8030 C2550
CS-6030, CS-8030 C2640 Side Feeder Drive Motor Error.
CS-6030, CS-8030 C3100
PF-660 Lift Motor Descent Error. During initialization or door open lower limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation. During paper feed lower limit detection switch does not turn OFF withing 200ms.
Duplex Side Registration Motor Error. The duplex side registration home position sensor does not detect the home position of the side registration guide.
Developing Motor Error. After developing motor has been activated for 1 sec, lock signal remains high for 1 sec.
Drive Motor Error. After drive motor has been activated for 1 sec, lock signal remains high for 1 sec.
Fuser Motor Error. After fuser motor has been activated for 1 sec, lock signal remains high for 1 sec.
Transfer Motor Error. After transfer motor has been activated for 1 sec, lock signal remains high for 1 sec.
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying using MP tray.
CS-6030, CS-8030 C3200
CS-6030, CS-8030 C3210
CS-6030, CS-8030 C3300
CS-6030, CS-8030 C3310
CS-6030, CS-8030 C3500
CS-6030, CS-8030 C3900
CS-6030, CS-8030 C3910
CS-6030, CS-8030 C4000
CS-6030, CS-8030 C4010
Exposure Lamp Problem. Exposure lamp does not reach the input value threshold 500ms after the lamp is activated and the carriage is moved to the shading position and an additional 100ms later. The exposure lamp does not light after 50 tries.
CIS Lamp Problem. CIS lamp does not exceed the input value threshold within 5 sec of commencing reading.
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
CIS AGC Problem. After AGC correct input is not obtained at the CIS.
Communication Error Between Scanner and SHD.
Scanner PWB Backup Memory Read/Write Error. Read & Write data does not match.
Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
Polygon Motor Steady-State Problem. Stabilization is lost exceeding 5 sec after the polygon motor is stabilized.
CS-6030, CS-8030 C4100
CS-6030, CS-8030 C4110
CS-6030, CS-8030 C4120
CS-6030, CS-8030 C4200
CS-6030, CS-8030 C5100
CS-6030, CS-8030 C5500
CS-6030, CS-8030 C5510
CS-6030, CS-8030 C5600
CS-6030, CS-8030 C5610
BD Initialization (A) Problem. During initialization only laser A is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
BD Initialization (B) Problem. During initialization only laser B is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
BD Initialization (C) Problem. During initialization only laser C is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
BD Steady-State Problem. ASIC of the main PWB detects a Beam Detect error A for 4000ms after polygon motor stabilization.
Main High Voltage Error. While the main high voltage output remote signal is ON, an alarm signal is detected continuously for 400ms.
Drum Surface Potential Sensor Problem 1. The sensor output is 0.5v or less when MC REM signal is turned ON.
Drum Surface Potential Sensor Problem 2. The sensor output is 4.5v or more when MC REM signal is turned ON.
Drum Surface Potential Problem 1. Grid voltage at 4.5v could not determine the potential. Potential adjustment after 30 tries could not raise the potential sensor value to the predetermined value.
Drum Surface Potential Problem 2. Grid voltage at 0.3v could not determine the potential. Potential adjustment after 30 tries could not lower the potential sensor value to the predetermined value.
CS-6030, CS-8030 C6000
CS-6030, CS-8030 C6020
CS-6030, CS-8030 C6030
CS-6030, CS-8030 C6050
CS-6030, CS-8030 C6400
CS-6030, CS-8030 C7200
CS-6030, CS-8030 C7210
CS-6030, CS-8030 C7300
CS-6030, CS-8030 C7800
CS-6030, CS-8030 C7810
Fuser Heater Lamp Break. The fuser temperature does not increase for 40 sec after the fuser heaters have been turned ON. The fuser temperature remains below 50C/122F for 10 sec continuously after the fuser heaters have been turned ON during stabilization.
Fuser Thermistor High Temperature Detection Error. Fuser temperature exceeds 235C/455F for 10 sec. The fuser high temperature signal is detected continuously for 500ms.
Fixing Thermistor Break Error. The fusing thermistor remains lower than 1C/33.8F for 30 sec continuously when the fuser heater is on.
Fuser Thermistor Abnormal Temperature Detection. During copying the temperature at the heat roller is detected lower than 120C/248F continuously for 5 sec.
Zero-Cross Signal Error. The engine PWB does not detect the zreo-crossing signal (Z CROSS SIG) for 5 sec.
Broken Internal Thermistor Wire. The thermistor output value is 4.5v or more.
Short-Circuited Internal Thermistor. Thermistor input value is 0.5v or less.
Toner Hopper Problem. During toner replenishment after toner empty has been detected, toner empty could not be cleared in three times of 360 sec.
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
CS-6030, CS-8030 C8010
CS-6030, CS-8030 C8020
CS-6030, CS-8030 C8030
CS-6030, CS-8030 C8040
DF-650 Document Finisher Paper Conveying Motor Problem. After the first 1 sec of activation, the LOCK signal of the paper conveying motor is detected for more than 500ms while the paper conveying motor is activated.
PH-4A Punch Motor Problem. After the first 1 sec of activation, the LOCK signal of the punch motor is detected for more than 500ms while the punch motor is activated.
DF-650 Upper Paper Conveying Belt Problem. During initialization the intermediate tray upper sliding plate is not detected in the home position within 3 sec after the belt retuns to the home position, resulting in Jam 87. When the intermediate tray upper sliding plate is operated from the home position the upper paper conveying belt HPS does not turn OFF within 1 sec.
DF-650 Lower Paper Conveying Belt Problem. During initialization the intermediate tray lower sliding plate is not detected in the home position within 3 sec after the belt retuns to the home position, resulting in Jam 87. When the intermediate tray lower sliding plate is operated from the home position the lower paper conveying belt HPS does not turn OFF within 1 sec.
CS-6030, CS-8030 C8140
CS-6030, CS-8030 C8150
CS-6030, CS-8030 C8170
CS-6030, CS-8030 C8180
DF-650 Main Tray Problem. The main tray upper limit detection switch or the main tray load detection switch do not detect the main tray within 20 sec from start of ascention. During ascention, the main tray upper limit detection sensor of the main tray load detection switch does not turn OFF within 500ms after it turns ON. During ascention, the main tray upper limit detection sensor of the main tray load detection switch stays ON exceeding 2 sec.
DF-650 Muti-Job Tray Problem. The multi-job tray upper limit detection switch does not detect the multi-job tray within 20 sec from start of ascention. During ascention, the multi-job tray upper limit detection sensor does not turn OFF within 500ms after it turns ON.
DF-650 Front Upper Side Registration Guide Problem. During initialization, the front upper side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the front upper side registration guide is operated from the home position, the front upper side registration home position sensor does not turn OFF within 500ms.
DF-650 Rear Upper Side Registration Guide Problem. During initialization, the rear upper side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the rear upper side registration guide is operated from the home position, the rear upper side registration home position sensor does not turn OFF within 500ms.
CS-6030, CS-8030 C8190
CS-6030, CS-8030 C8210
CS-6030, CS-8030 C8220
CS-6030, CS-8030 C8230
DF-650 Lower Side Registration Guide Problem. During initialization, the front/rear lower side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the lower side registration guide is operated from the home position, the lower side registration home position sensor does not turn OFF within 500ms.
DF-650 Front Stapler Problem. During initial rotations, front stapler home position is not detected within 500ms after the front stapler returns to home postion, resulting in a Jam 90. When the front stapler is operated from the home position, the front staple home position sensor does not turn OFF within 500ms.
DF-650 Front Clincher Problem. During initial rotations, front clincher home position is not detected within 500ms after the front clincher returns to home postion, resulting in a Jam 90. When the front clincher is operated from the home position, the front clincher home position sensor does not turn OFF within 500ms.
DF-650 Rear Stapler Problem. During initial rotations, rear stapler home position is not detected within 500ms after the rear stapler returns to home postion, resulting in a Jam 90. When the rear stapler is operated from the home position, the rear staple home position sensor does not turn OFF within 500ms.
CS-6030, CS-8030 C8240
CS-6030, CS-8030 C8300
CS-6030, CS-8030 C8310
CS-6030, CS-8030 C8320
CS-6030, CS-8030 C8330
CS-6030, CS-8030 C9040
CS-6030, CS-8030 C9050
DF-650 Rear Clincher Problem. During initial rotations, rear clincher home position is not detected within 500ms after the rear clincher returns to home postion, resulting in a Jam 90. When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn OFF within 500ms.
BF-1(A) Centerfold Unit Communiation Problem. Although the connection is detected, communication is not possible with the centerfold unit.
BF-1(A) Centerfold Unit Side Registration Guide Problem. During initial rotations front/rear side registration guides are not detected in home position within 600ms after the guides return to home position. When the side registration guide is operated from the home position, the side registration guide HPS does not turn OFF within 100ms.
BF-1(A) Centerfold Unit Centering Plate Problem. During initialization, the centering plate is not detected in the home position when the centering plate returns to home position.
BF-1(A) Centerfold Blade Problem. During initialization the centerfold blade is not detected in the home position within a specified period of time.
DP Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned ON.
DP Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned ON.
CS-6030, CS-8030 C9060
CS-6030, CS-8030 C9070
CS-6030, CS-8030 C9080
CS-6030, CS-8030 E001
CS-6030, CS-8030 E010
CS-6030, CS-8030 E011
CS-6030, CS-8030 E012
CS-6030, CS-8030 E020
CS-6030, CS-8030 E021
CS-6030, CS-8030 E022
DP EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
DP Communication Problem between the DP and SHD. A communication error is detected.
DP Communication Error between the DP and CIS. Reading cannot be performed correctly.
Scan Sys (G) Transmission in progress was cancelled by operator.
Scan Sys (G) Destination computer could not be found during data transmission. (An error occurred that could not be classified more clearly under any error code after E011.) The scanner could not find the computer that was running the personal Address Book.
Scan Sys (G) Transmission was stopped due to problems with the image data itself.
Scan Sys (G) The scanner attempted to transmit image data, but was unable to access the corresponding information in the personal Address Book due to a connection problem.
Scan Sys (G) An attempt to use the Send E-mail function was made, but the scanner was unable to find the SMTP server.
Scan Sys (G) The destination of the email is listed under the restricted domain names, or is not listed under the permitted domain names.
Scan Sys (G) The mail contained an email address that the SMTP server could not find.
CS-6030, CS-8030 E023
CS-6030, CS-8030 E024 Scan Sys (G) SMTP Authentication error.
CS-6030, CS-8030 E030
CS-6030, CS-8030 E031
CS-6030, CS-8030 E032
CS-6030, CS-8030 E033
CS-6030, CS-8030 E034
CS-6030, CS-8030 E035
CS-6030, CS-8030 E036
Scan Sys (G) The SMTP server is not operating properly.
Scan Sys (G) The destination computer cannot be found. Either the Scan File Utility is not running or it is already communicating with another scanner.
Scan Sys (G) The scanner attempted to transmit image data, but the registered password did not match the password in the destination computer.
Scan Sys (G) During the scan-to-PC operation, the hard drive on the destination computer ran out of available space.
Scan Sys (G) The versions of the Scan File Utility do not match.
Scan Sys (G) Transmission was not possible because the Scan File Utility is communicating with another scanner
Scan Sys (G) During group transmission, the number of the save folder registered in the Scan File Utility did not match.
Scan Sys (G) During compression of the scanned image data, the data size went over the maximum limit.
CS-6030, CS-8030 E039
CS-6030, CS-8030 E059
CS-6030, CS-8030 E061
CS-6030, CS-8030 E080
CS-6030, CS-8030 E081
CS-6030, CS-8030 E082
CS-6030, CS-8030 E083
Scan Sys (G) The response received from the destination computer under the Scan-to-PC function was not an appropriate one. Unexpected trouble has occurred in the destination computer.
Scan Sys (G) A command received from the transmitting computer was not an appropriate one. Trouble has occurred in the computer that is running the corresponding personal Address Book.
Scan Sys (G) When selecting the group in the destination computer under either the Send E-mail or Scan to PC functions, some type of trouble has occurred in the information for the registered members of the group.
Scan Sys (G) The FTP server cannot be found.
Scan Sys (G) The FTP server is failed to login.
Scan Sys (G) The storing path is incorrect.
Scan Sys (G) The error occurred in the FTP server.
CS-6030, CS-8030 E101
CS-6030, CS-8030 message "Check domain name and host name."
CS-6030, CS-8030 message
CS-6030, CS-8030 message "Communication error."
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message "Destination PC is in use. Try again later."
CS-6030, CS-8030 message
CS-6030, CS-8030 message "Destination PC's system error."
Scan Sys (G) An error has occurred while selecting multiple destinations.
"Check the DB Assistant PC. Contact administrator."
"DB Assistant Server error. Contact administrator."
"DB Assistant Server is in use. Try again later."
"DB Assistant Server version is different. Contact administrator."
"Destination address is not being registered."
"Destination PC's application is out of order."
CS-6030, CS-8030 message
CS-6030, CS-8030 message "E-mail size exceeds data capacity."
CS-6030, CS-8030 message
CS-6030, CS-8030 message "Network scanner system error."
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message "Registration full."
CS-6030, CS-8030 message
CS-6030, CS-8030 message
"Destination PC's version is different. Contact administrator."
"Error occurred at FTP Server. Please contact administrator."
"No destination address being registered."
"Overflow of original pages. Scanned documents were sent."
"PC of personal address list is in use. Try again later."
"Sender (user) is not registered. Contact administrator."
"SMTP Authentication error. Contact administrator."
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
CS-6030, CS-8030 message
"The file was not saved. Check the destination PC."
"The path attempted to use for saving does not exist."
"This name is already in use. Input new name again."
"This number is already in use. Input new number again."
"Unable to find destination PC. Check the PC."
"Unable to find FTP server. Contact administrator."
"Unable to find PC of personal address list."
"Unable to find SMTP server. Contact administrator."
CS-6030, CS-8030 message "Unable to Log in to the FTP Server."
CS-6030, CS-8030 message "Unable to use the scanner."
CS-6030, CS-8030 message "Wrong password."
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
21 Start > Execute > Start.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data: 10871087
Turn power Off/On. If code immediately returns initialize backup data for image processing: 10871087
Start > Engine > Execute > Start. (tech only)
10871087 906 Start > Execute > Start
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Start > Execute > Start > Stop/Clear > 24 > Start > Execute > Start.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data for scanning: 10871087
Start > SCANNER+DP > Execute > Start. (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Service Checks
1) Repl main PWB.
1) Run simulation U21, 2) Repl main PWB.
1) Reseat YC26 @ main PWB & relay PWB, 2) Temporarily run sim U935. Status 10871087 > 935 > Start > select mode (60=MODE 1, 80=MODE 2) > Start > Clear > 1 > Start. (default=MODE 0)
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Run simulation U022, 2) Repl engine PWB.
1) Replace EEPROMs, 2) Repl engine PWB, 3) Repl main PWB.
1) Replace EEPROMs, 2) Repl engine PWB, 3) Repl main PWB.
1) Reseat YC1 @ main PWB & YC1 @ engine PWB, 2) Repl main PWB, 3) Repl engine PWB.
1) Reseat YC2 @ engine PWB & YC5 @ scanner PWB, 2) Repl main PWB, 3) Repl scanner PWB.
1) Reseat YC9 @ main PWB & YC5 @ printer PWB, 2) Reseat DIMM, 3) Repl printer PWB, 4) Repl main PWB.
1) Repl DIMM, 2) Repl main PWB.
1) Repl main PWB.
1) Reseat YC3 @ main PWB, 2) Reseat network scanner board, 3) Repl network scanner PWB, 4) Repl main PWB.
1) Reseat YC26 @ main PWB & relay PWB, 2) Temporarily run sim U935. Status 10871087 > 935 > Start > select mode (60=MODE 1, 80=MODE 2) > Start > Clear > 1 > Start. (default=MODE 0)
1) Reseat YC6 @ scanner PWB & YC1 @ DP main PWB, 2) Repl DP main PWB.
Reseat YC15 @ engine PWB & YC3 @ side feeder main PWB, 2) Repl side feeder main PWB, 3) Repl main PWB.
1) Reseat YC14 @ engine PWB & YC4 @ finisher main PWB, 2) Repl finisher main PWB, 3) Repl main PWB.
1) Reseat YC2 @ engine PWB & YC2 @ duplex PWB, 2) Repl duplex PWB, 3) Repl main PWB.
1) Reseat YC3 @ engine PWB & YC2 @ deck PWB, 2) Repl engine PWB.
1) Reseat YC4 @ engine PWB & YC2 @ cassette PWB, 2) Repl engine PWB.
1) Repl side feeder main PWB.
1) Repl finisher main PWB.
1) Reseat YC11 @ engine PWB & HDD connectors, 2) Run U906 (partial reset) & U024 (HDD formatting), 3) Repl HDD harnass, 4) Repl main PWB.
1) Reseat YC5 @ engine PWB & developing unit connector, 2) Reseat developing unit, 3) Repl developing unit, 4) Repl engine PWB.
1) Reseat YC5 @ engine PWB & cleaning unit connector, 2) Reseat cleaning unit, 3) Repl cleaning unit, 4) Repl engine PWB.
1) Reseat lift upper limit switch connector & lift motor 1 connector, 2) Check for lift drive problem 3) Check for open motor coil. Repl Lift Motor 1, 4) Run sim U031 to test lift upper limit switch. (LIM SW1 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl deck PWB.
1) Reseat lift upper limit switch connector & lift motor 2 connector, 2) Check for lift drive problem 3) Check for open motor coil. Repl Lift Motor 2, 4) Run sim U031 to test lift upper limit switch. (LIM SW2 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl deck PWB.
1) Reseat lift upper limit switch connector & lift motor 3 connector, 2) Check for lift drive problem 3) Check for open motor coil. Repl lift motor 3, 4) Run sim U031 to test lift upper limit switch. (LIM SW3 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl cassette PWB.
1) Reseat lift upper limit switch connector & lift motor 4 connector, 2) Check for lift drive problem 3) Check for open motor coil. Repl lift motor 4, 4) Run sim U031 to test lift upper limit switch. (LIM SW4 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl cassette PWB.
1) Reseat upper limit switch & lift motor connector. 2) Measure +/-24vdc YC5-A12 (SFLM+) to YC6-B11 (safety switch loop-) @ side feeder main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl side feeder main PWB. 3) If voltage present check safety switches ULSSW, LLSSW, RCSSW, & SFLM (lift motor).
1) Reseat upper limit switch & lift motor connector. 2) Measure +/-24vdc YC4-1 (-) to YC4-9 (+) @ SF main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl SF main PWB. 3) If DC present measure +/-24vdc YC4-5 (-) to YC4-6 (+) @ SF main PWB while running sim U247 (same as above). If DC absent check safety switches ULSSW, LLSSW, TSSW. If DC present but motor doesn't run repl SFLM (lift motor).
1) Reseat lower limit switch & lift motor connector. 2) Measure +/-24vdc YC5-A12 (SFLM+) to YC6-B11 (safety switch loop-) @ side feeder main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl side feeder main PWB. 3) If voltage present check safety switches ULSSW, LLSSW, RCSSW, & SFLM (lift motor).
1) Reseat lower limit switch & lift motor connector. 2) Measure +/-24vdc YC4-1 (-) to YC4-9 (+) @ SF main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl SF main PWB. 3) If DC present measure +/-24vdc YC4-5 (-) to YC4-6 (+) @ SF main PWB while running sim U247 (same as above). If DC absent check safety switches ULSSW, LLSSW, TSSW. If DC present but motor doesn't run repl SFLM (lift motor).
1) Reseat YC29 @ engine PWB & YC1 @ duplex PWB, 2) Repl duplex side registration motor, 3) Repl duplex PWB.
1) Reseat developing motor connector, 2) Check for drive problems, 3) Repl developing motor, 4) Repl duplex PWB.
1) Reseat YC2 & YC11 on the deck PWB, 2) Check for drive problems, 3) Repl drive motor, 4) Repl deck PWB, 5) Repl engine PWB.
1) Reseat YC2 & YC4 on the duplex PWB, 2) Check for drive problems, 3) Repl fuser motor, 4) Repl duplex PWB, 5) Repl engine PWB.
1) Reseat YC2 & YC3 on the cassette PWB, 2) Check for drive problems, 3) Repl transfer motor, 4) Repl cassette PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Repl side feeder drive motor, 3) Repl side feeder main PWB.
1) Check for drive problems, 2) Reseat YC2, YC5, & YC10 @ scanner PWB, 3) Reseat conn scanner home position switch, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl scanner PWB.
1) Repl scanner PWB.
1) Reseat YC3, YC4, & YC5 @ scanner PWB, 2) Reseat YC5, YC6, & YC8 @ SHD PWB, 3) Reseat YC1, YC2, & YC3 @ CCD PWB, 4) Reseat conn @ inverter PCB, 5) Adjust position of shading plate, 6) Repl scanner HPS 7) Repl exposure lamp & inverter PWB, 8) Repl scanner PWB, 9) Replace CCD PWB.
1) Reseat YC2 @ DP Main PWB, 2) Repl DP inverter PWB, 3) Repl CIS, 4) Repl DP main PWB.
1) Reseat YC5, YC6, & YC8 @ SHD PWB, 2) Reseat YC1, YC2, & YC3 @ CCD PWB, 4) Reseat conn @ inverter PCB, 5) Adjust position of shading plate, 6) Repl scanner HPS 7) Repl exposure lamp & inverter PWB, 8) Repl scanner PWB, 9) Replace CCD PWB.
1) Repl DP inverter PWB, 2) Repl CIS, 3) Repl DP main PWB.
1) Reseat YC3 @ scanner PWB & YC4 @ SHD PWB, 2) Pinout harnass, 3) Repl scanner PWB, 4) Repl SHD PWB.
1) Run simulation U022, 2) Repl scanner PWB.
1) Reseat laser unit connectors, 2) Measure 24vdc on YC17-1 @ engine PWB to frame ground. If present, repl laser unit, 3) If absent, repl engine PWB.
1) Reseat laser unit connectors, 2) Measure 24vdc on YC17-1 @ engine PWB to frame ground. If present, repl laser unit, 3) If absent, repl engine PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC7 @ engine PWB, 2) Repl main charger unit, 3) Repl high voltage PWB.
1) Reseat YC5 @ engine PWB, 2) Repl drum surface potential sensor, 3) Repl high voltage PWB, 4) Repl engine PWB.
1) Reseat YC5 @ engine PWB, 2) Repl drum surface potential sensor, 3) Repl high voltage PWB.
1) Repl main charger wire, 2) Clean grid or main charger shield, 3) Repl drum surface potential sensor, 4) Repl high voltage PWB, 5) Repl engine PWB.
1) Repl drum surface potential sensor, 2) Repl high voltage PWB, 3) Repl drum, 4) Repl engine PWB.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters L, M, & S, 4) Repl AC PS PWB, 5) Repl engine PWB.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Replace thermistor M & S, 3) Repl engine PWB.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Replace thermistor M & S, 3) Repl engine PWB, 4) Repl AC PS PWB
1) Check that thermistor M & S are contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters L, M, & S, 4) Repl AC PS PWB, 5) Repl engine PWB.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC11 @ engine PWB & YC6 @ DC PS PWB, 3) If zero-cross signal is not output from YC6-3 @ DC PS PWB, repl DC PS PWB, 3) If zero-cross signal is detected from YC6-3 @ DC PS PWB (and C6400), repl engine PWB.
1) Reseat YC23 @ engine PWB, 2) Repl humidity sensor, 3) Repl engine PWB.
1) Reseat YC23 @ engine PWB, 2) repl humidity sensor, 3) Repl engine PWB.
1) Reseat YC2 & YC5 @ deck PWB & YC3 @ engine PWB, 2) Pinout harnass, 3) Replace toner level detection sensor.
1) Reseat YC13 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Reseat YC13 @ engine PWB, 2) Pinout harnass, 3) Repl the humidity sensor.
1) Reseat YC14 @ finisher main PWB, 2) Check for drive problems, 3) Repl paper conveying motor, 4) Repl finisher main PWB.
1) Reseat YC13 @ finisher main PWB & YC1 @ punch PWB, 2) Check for drive problems, 3) Repl punch motor, 4) Repl finisher main PWB.
1) Reinsert intermediate tray, 2) Reseat the upper paper conveying belt HPS connector. 3) Repl upper paper conveying belt HPS, 4) Repl upper paper conveying belt motor, 5) Repl finisher main PWB.
1) Reinsert intermediate tray, 2) Reseat the lower paper conveying belt HPS connector. 3) Repl lower paper conveying belt HPS, 4) Repl lower paper conveying belt motor, 5) Repl finisher main PWB.
1) Reseat sensor & main tray elevator motor connectors, 2) Repl tray sensors 3) Repl main tray elevator motor, 4) Repl finisher main PWB.
1) Reseat sensor & multi-job tray elevator motor connectors, 2) Repl tray sensor 3) Repl multi-job tray elevator motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front upper side registration home position sensor, 3) Repl front upper side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear upper side registration home position sensor, 3) Repl rear upper side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl lower side registration home position sensor, 3) Repl lower side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front stapler home position sensor, 3) Repl front stapler motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front clincher home position sensor, 3) Repl front clincher motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear stapler home position sensor, 3) Repl rear stapler motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear clincher home position sensor, 3) Repl rear clincher motor, 4) Repl finisher main PWB.
1) Reseat centerfold set switch connector, 2) Repl centerfold unit set switch, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl side registration guide home position sensor, 3) Repl side registration guide motor, 4) Repl centerfold main PWB.
1) Reseat sensor & motor connectors, 2) Repl centering plate home position sensor, 3) Repl centering plate motor, 4) Repl centerfold main PWB.
1) Reseat sensor & motor connectors, 2) Repl centerfold blade home position sensor, 3) Repl centerfold blade motor, 4) Repl centerfold main PWB.
1) Reseat sensor & motor connectors, 2) Repl DP lift upper limit switch, 3) Repl DP lift motor, 4) Repl DP main PWB.
1) Reseat sensor & motor connectors, 2) Repl DP lift lower limit switch, 3) Repl DP lift motor, 4) Repl DP main PWB.
Try to perform the operation again.
1) Repl DP main PWB, 2) Contact Service Administration Division.
1) Check all connectors @ SHD PWB, 2) Pinout connectors/harnass, 3) Repl SHD PWB, 4) Repl DP main PWB.
1) Check all connectors @ CIS, 2) Pinout connectors/harnass, 3) Repl CIS.
Check to make sure that the destination computer is operating properly. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check to make sure that the computer that is running the personal Address Book is running properly.
Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly. Check with the netowork administrator to find out whether the SMTP server is working properly.
Check the restricted and/or permitted domain names, and adjust the settings as necessary. Check to make sure that the destination email address was entered correctly.
Check to make sure that the destination email address was entered correctly.
Check the versions of the Scan File Utility.
Check the Scan File Utility Settings.
Check with your network administrator to find out whether the SMTP server is working properly.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
Check to make sure that the Scan File Utility is running properly in that computer, or whether it is already connected to another scanner. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check the password that is set in the destination computer.
Increase the available space on the destination computer's hard drive, then try the operation again.
Try to perform the operation again after the connection to the other scanner is completed.
Perform any or all of the following procedures in order to lower the amount of data and then try scanning and transmission operation again: 1) lower the resolution of the image data. 2) Change the image quality setting to OCR. 3) Lower the number of documents (pages) that are being scanned at one time.
Check to make sure that the Scan File Utility in the destination computer is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, running in the destination computer. If the trouble is with the destination computer, fix the problem.
Check to make sure that the personal Address Book is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, also running on the computer that is running the persoal Address Book. If the trouble is with the computer that is running the personal Address Book, fix that problem.
Check the computer of each group member as necessary and, if there is trouble in any of those computers, fix that problem.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
Check each error and fix the corresponding problems.
The scanner's domain name and host name have not been registered properly. Check the correct domain name and host name. (Refer to "(3) Making settings from the touch panel".)
The DB Assistant cannot be found. Make sure that the DB Assistant is running properly on the computer on which it is installed.
If you are using the Scan to PC function, check the status of the destination computer and then try the operation again. If you are using the Send E-mail function, check to make sure that the SMTP server is running, or consult with the network administrator. If you are using the DB Assistant function, check to make sure that the DB Assistant is installed on the computer.
Communication could not be continued because an error occurred with the DB Assistant or with the computer on which it is installed.
DB Assistant is currently communicating with another scanner. Wait for a while and then try the operation again.
The versions of the DB Assistant do not match. Consult the network administrator.
The entered number is not appropriate. Check the correct number and enter it again.
The destination computer and the scanner are currently communicating. Wait for a while and then try the operation again.
Check to make sure that the Scan File Utility is running in the destination computer.
Check the status of the destination computer and then try the operation again.
Restart the scanner.
The versions of the Address Book do not match. Consult your network administrator.
Reduce the number of pages being transmited, or lower the scanning resolution, and try to transmit again.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
The selected destination is not registered. Register that destination or select another one.
The number of scanned documents exceeds 999, the maximum that can be transmitted at one time. Transmit any further pages separately. When transmitting under settings such as "two-sided" or "booklet", there may be a case where only 998 pages can be scanned and transmitted.
The designated AddressBook and the scanner are currently communicating. Wait a while and then try the operation again.
Delete any unnecessary items and try the procedure again.
User Number 001 is not registered in the "Select sender name" List of this scanner. First register a user under that number or turn the "Selection of senders (users)" setting OFF, then select another user.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
Register a different name.
Register a different number.
If the amount of data exceeds the hard disk capacity as registered in the Scan File Utility on the destination computer, increase the available space on your computer's hard disk and then try the operation again. If data with the same file name has been sent from more than one scanner at a time, the data cannot be saved. Wait for a while and then try the operation again, or change the file name.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
There is a problem at your computer. Check to make sure that the Scan File Utility is running and the computer is able to receive data.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
If the Address Book software is not running on your computer, start it up. If it is already running, make sure that your computer is connected properly to the network and the network cable is connected properly to the Scanner NIC card.
Check to make sure the network cable connected securely and properly. If the message appears immediately after turning the scanner ON, wait approximately 2 minutes while the scanner NIC boots up. Check to make sure that the SMTP server is running, or consult with your network administrator.
Enter the correct password.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
Check to make sure that the network cable is connected securely and properly. If the message appears immediately after turning the scanner On, wait approximately 2 minutes while the scanner NIC boots up.
Model Error Code DescriptionC0060 Main PWB Type Mismatch Error.
CS-620, CS-820 C0100
CS-620, CS-820 C0110
CS-620, CS-820 C0130
CS-620, CS-820 C0140
CS-620, CS-820 C0150
CS-620, CS-820 C0160
CS-620, CS-820 C0170
CS-620, CS-820 C0180
CS-620, CS-820 C0210
CS-620, CS-820 C0220
CS-620, CS-820 C0240
CS-620 (2KN), CS-820 (2KP)
Backup Memory Read/Write Problem. Read and write data does not match.
Main PWB Backup Memory Data Problem. Data in the specified area of the backup memory does not match specified values.
Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
Engine PWB EEPROM Backup Memory Data Problem. Data for backup data check is changed at the check after startup.
Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
CPU Communication Problem. Synchronization cannot be taken between the main CPU and engine CPU.
CPU Communication Problem. Synchronization cannot be taken between the main CPU and scanner CPU.
Printer Board Communication Problem. Printer board does not respond within 120 sec after power ON.
CS-620, CS-820 C0250
CS-620, CS-820 C0330 Relay Board Communication Problem.
CS-620, CS-820 C0410
CS-620, CS-820 C0420
CS-620, CS-820 C0440
CS-620, CS-820 C0460
CS-620, CS-820 C0500
CS-620, CS-820 C0510
CS-620, CS-820 C0610
CS-620, CS-820 C0630
CS-620, CS-820 C0640 Hard Disk Drive cannot be accessed.
Network Scanner Board Communication Problem. Network scanner board does not respond to the alive command three times within 30 sec. Network scanner board does not respond to the communication command within 75 sec.
DP Communication Problem. There is no reply after 5 tries at communication. A communication error has occurred.
PF-650(B)/PF-660(B) Communication Error. A communication error is detected 10 times in succession.
DF-650(B) Communication Problem. A communication error from document finisher is detected 10 times in succession.
Duplex Unit Communication Problem. A communication error frum duplex section is detected 10 times in succession.
Paper Feed Unit Communication Error. A communication error is detected 10 times in succession from cassettes 1 & 2.
Paper Feed Unit Communication Error. A communication error is detected 10 times in succession from cassettes 3 & 4.
Bitmap Problem. The DIMM on the scanner Main PWB does not operate correctly.
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-620, CS-820 C0700
CS-620, CS-820 C0750
CS-620, CS-820 C0760
CS-620, CS-820 C0770
CS-620, CS-820 C0800
CS-620, CS-820 C0960
CS-620, CS-820 C0970
CS-620, CS-820 C1010
CS-620, CS-820 C1020
CS-620, CS-820 C1030
PF-650(B)/PF-660(B) EEPROM Error. An error occurs in EEPROM (U4) data read or write for the side feeder main PWB.
DF-650(B) EEPROM Error. A backup memory error is received in serial communication data from the finisher.
PH-4A Punch Unit EEPROM Error. An error occurs in EEPROM data read or write for the punch PWB.
BF-1(B) Centerfold Unit EEPROM Error. An error occurs in EEPROM data read or write for the centerfold unit main PWB.
Image Processing Problem. Secondary feed timeout. JAM05 is detected twice.
Developing Unit EEPROM Error. An error occurs in EEPROM data read or write for the developing unit.
Cleaning Unit EEPROM Error. An error occurs in EEPROM data read or write for the cleaning unit.
Cassette #1 Lift Motor error. When cassette is inserted lift upper limit switch 1 does not turn ON within 33 sec of lift motor 1 activation, 4 times successively. During copying lift upper limit switch 1 does not turn on within 1 sec of lift motor 1 activation 4 times successively.
Cassette #2 Lift Motor error. When cassette is inserted lift upper limit switch 2 does not turn ON within 33 sec of lift motor 2 activation 4 times successively. During copying lift upper limit switch 2 does not turn on within 1 sec of lift motor 2 activation 4 times successively.
Cassette #3 Lift Motor error. When cassette is inserted lift upper limit switch 3 does not turn ON within 33 sec of lift motor 3 activation 4 times successively. During copying lift upper limit switch 3 does not turn on within 1 sec of lift motor 3 activation 4 times successively.
CS-620, CS-820 C1040
CS-620, CS-820 C1140
CS-620, CS-820 C1140
CS-620, CS-820 C1150
Cassette #4 Lift Motor error. When cassette is inserted lift upper limit switch 4 does not turn ON within 33 sec of lift motor 4 activation 4 times successively. During copying lift upper limit switch 4 does not turn on within 1 sec of lift motor 4 activation 4 times successively.
PF-650(B) Lift Motor Ascention Error. During initialization or door open upper limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation 4 times successively. During paper feed upper limit detection switch does not turn OFF within 200ms, four times successively.
PF-660(B) Lift Motor Ascention Error. During initialization or door open upper limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation. During paper feed upper limit detection switch does not turn OFF within 200ms.
PF-650(B) Lift Motor Descent Error. During initialization or door open lower limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation 4 times successively. During paper feed lower limit detection switch does not turn OFF withing 200ms four times successively.
CS-620, CS-820 C1150
CS-620, CS-820 C1200
CS-620, CS-820 C2100
CS-620, CS-820 C2200
CS-620, CS-820 C2250
CS-620, CS-820 C2300
CS-620, CS-820 C2550
CS-620, CS-820 C2640
CS-620, CS-820 C2720
CS-620, CS-820 C3100
PF-660(B) Lift Motor Descent Error. During initialization or door open lower limit detection switch does not turn OFF within 15 sec of the side feeder lift motor activation 4 times successively. During paper feed lower limit detection switch does not turn OFF withing 200ms four times successively.
Duplex Side Registration Motor Error. The duplex side registration home position sensor does not detect the home position of the side registration guide.
Developing Motor Error. After developing motor has been activated for 1 sec, lock signal remains high for 1 sec.
Drive Motor Error. After drive motor has been activated for 1 sec, lock signal remains high for 1 sec.
Cleaning Motor Error. After cleaning motor has been activated for 1 sec, lock signal remains high for 1 sec.
Fuser Motor Error. After fuser motor has been activated for 1 sec, lock signal remains high for 1 sec.
Transfer Motor Error. After transfer motor has been activated for 1 sec, lock signal remains high for 1 sec.
PF-650(B)/PF-660(B) Side Feeder Drive Motor Error.
PTC Cleaning Motor Error. After PTC cleaning motor has been activated for 200ms sec, lock signal remains high for 1 sec. (?)
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying using MP tray.
CS-620, CS-820 C3200
CS-620, CS-820 C3210
CS-620, CS-820 C3300
CS-620, CS-820 C3310
CS-620, CS-820 C3500
CS-620, CS-820 C3900
CS-620, CS-820 C3910
CS-620, CS-820 C4000
CS-620, CS-820 C4010
CS-620, CS-820 C4100
Exposure Lamp Problem. Exposure lamp does not reach the input value threshold 500ms after the lamp is activated and the carriage is moved to the shading position and an additional 100ms later. The exposure lamp does not light after 50 tries.
CIS Lamp Problem. CIS lamp does not exceed the input value threshold within 5 sec of commencing reading.
CCD AGC Problem. After AGC correct input is not obtained at the CCD.
CIS AGC Problem. After AGC correct input is not obtained at the CIS.
Communication Error Between Scanner and SHD.
Scanner PWB Backup Memory Read/Write Error. Read & Write data does not match.
Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
Polygon Motor Steady-State Problem. Stabilization is lost exceeding 5 sec after the polygon motor is stabilized.
BD Initialization (A) Problem. During initialization only laser A is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
CS-620, CS-820 C4110
CS-620, CS-820 C4120
CS-620, CS-820 C4200
CS-620, CS-820 C5100
CS-620, CS-820 C5500
CS-620, CS-820 C5510
CS-620, CS-820 C5600
CS-620, CS-820 C5610
CS-620, CS-820 C6000
CS-620, CS-820 C6020
BD Initialization (B) Problem. During initialization only laser B is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
BD Initialization (C) Problem. During initialization only laser C is output, and ASIC of Main PWB detects a beam detect error for 2000ms.
BD Steady-State Problem. ASIC of the main PWB detects a Beam Detect error A for 4000ms after polygon motor stabilization.
Main High Voltage Error. While the main high voltage output remote signal is ON, an alarm signal is detected continuously for 400ms.
Drum Surface Potential Sensor Problem 1. The sensor output is 0.5v or less when MC REM signal is turned ON.
Drum Surface Potential Sensor Problem 2. The sensor output is 4.5v or more when MC REM signal is turned ON.
Drum Surface Potential Problem 1. Grid voltage at 4.5v could not determine the potential. Potential adjustment after 30 tries could not raise the potential sensor value to the predetermined value.
Drum Surface Potential Problem 2. Sensor output is 0.5v or less. Potential adjustment after 30 tries could not lower the potential sensor value to the predetermined value.
Fuser Heater Lamp Break. The fuser temperature does not increase for 40 sec after the fuser heaters have been turned ON. The fuser temperature remains below 50C/122F for 10 sec continuously after the fuser heaters have been turned ON during stabilization.
Fuser Thermistor High Temperature Detection Error. Fuser temperature exceeds 235C/455F for 10 sec. The fuser high temperature signal is detected continuously for 500ms.
CS-620, CS-820 C6030
CS-620, CS-820 C6050
CS-620, CS-820 C6400
CS-620, CS-820 C7200
CS-620, CS-820 C7210
CS-620, CS-820 C7300
CS-620, CS-820 C7800
CS-620, CS-820 C7810
CS-620, CS-820 C8000
CS-620, CS-820 C8010
CS-620, CS-820 C8020
Fixing Thermistor Break Error. The fusing thermistor remains lower than 0C/32F for 30 sec continuously when the fuser heater is on.
Fuser Thermistor Abnormal Temperature Detection. During copying the temperature at the heat roller is detected lower than 120C/248F continuously for 5 sec.
Zero-Cross Signal Error. The engine PWB does not detect the zreo-crossing signal (Z CROSS SIG) for 5 sec.
Broken Internal Thermistor Wire. The thermistor output value is 4.5v or more.
Short-Circuited Internal Thermistor. Thermistor input value is 0.5v or less.
Toner Hopper Problem. During toner replenishment after toner empty has been detected, toner empty could not be cleared in three times of 360 sec.
Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
Finisher Type Mismatch Problem. Absence of the finisher is detected.
DF-650(B) Document Finisher Paper Conveying Motor Problem. After the first 1 sec of activation, the LOCK signal of the paper conveying motor is detected for more than 500ms while the paper conveying motor is activated.
PH-4A Punch Motor Problem. After the first 1 sec of activation, the LOCK signal of the punch motor is detected for more than 500ms while the punch motor is activated.
CS-620, CS-820 C8030
CS-620, CS-820 C8040
CS-620, CS-820 C8140
CS-620, CS-820 C8150
DF-650(B) Upper Paper Conveying Belt Problem. During initialization the intermediate tray upper sliding plate is not detected in the home position within 3 sec after the belt retuns to the home position, resulting in Jam 87. When the intermediate tray upper sliding plate is operated from the home position the upper paper conveying belt HPS does not turn OFF within 1 sec.
DF-650(B) Lower Paper Conveying Belt Problem. During initialization the intermediate tray lower sliding plate is not detected in the home position within 3 sec after the belt returns to the home position, resulting in Jam 87. When the intermediate tray lower sliding plate is operated from the home position the lower paper conveying belt HPS does not turn OFF within 1 sec.
DF-650(B) Main Tray Problem. The main tray upper limit detection switch or the main tray load detection switch do not detect the main tray within 20 sec from start of ascention. During ascention, the main tray upper limit detection sensor of the main tray load detection switch does not turn OFF within 500ms after it turns ON. During ascention, the main tray upper limit detection sensor of the main tray load detection switch stays ON exceeding 2 sec.
DF-650(B) Muti-Job Tray Problem. The multi-job tray upper limit detection switch does not detect the multi-job tray within 20 sec from start of ascention. During descent, the multi-job tray upper limit detection sensor does not turn OFF within 500ms after it turns ON.
CS-620, CS-820 C8170
CS-620, CS-820 C8180
CS-620, CS-820 C8190
CS-620, CS-820 C8210
DF-650(B) Front Upper Side Registration Guide Problem. During initialization, the front upper side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the front upper side registration guide is operated from the home position, the front upper side registration home position sensor does not turn OFF within 500ms.
DF-650(B) Rear Upper Side Registration Guide Problem. During initialization, the rear upper side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the rear upper side registration guide is operated from the home position, the rear upper side registration home position sensor does not turn OFF within 500ms.
DF-650(B) Lower Side Registration Guide Problem. During initialization, the front/rear lower side registration guide is not detected in home position within 3 sec after the guide returns to home position, resulting in a Jam 87. When the lower side registration guide is operated from the home position, the lower side registration home position sensor does not turn OFF within 500ms.
DF-650(B) Front Stapler Problem. During initial rotations, front stapler home position is not detected within 500ms after the front stapler returns to home postion, resulting in a Jam 90. When the front stapler is operated from the home position, the front staple home position sensor does not turn OFF within 500ms.
CS-620, CS-820 C8220
CS-620, CS-820 C8230
CS-620, CS-820 C8240
CS-620, CS-820 C8300
CS-620, CS-820 C8310
CS-620, CS-820 C8320
DF-650(B) Front Clincher Problem. During initial rotations, front clincher home position is not detected within 500ms after the front clincher returns to home postion, resulting in a Jam 90. When the front clincher is operated from the home position, the front clincher home position sensor does not turn OFF within 500ms.
DF-650(B) Rear Stapler Problem. During initial rotations, rear stapler home position is not detected within 500ms after the rear stapler returns to home postion, resulting in a Jam 90. When the rear stapler is operated from the home position, the rear staple home position sensor does not turn OFF within 500ms.
DF-650(B) Rear Clincher Problem. During initial rotations, rear clincher home position is not detected within 500ms after the rear clincher returns to home postion, resulting in a Jam 90. When the rear clincher is operated from the home position, the rear clincher home position sensor does not turn OFF within 500ms.
BF-1(B) Centerfold Unit Communiation Problem. Although the connection is detected, communication is not possible with the centerfold unit.
BF-1(B) Centerfold Unit Side Registration Guide Problem. During initial rotations front/rear side registration guides are not detected in home position within 600ms after the guides return to home position. When the side registration guide is operated from the home position, the side registration guide HPS does not turn OFF within 100ms.
BF-1(B) Centerfold Unit Centering Plate Problem. During initialization, the centering plate is not detected in the home position when the centering plate returns to home position.
CS-620, CS-820 C8330
CS-620, CS-820 C9040
CS-620, CS-820 C9050
CS-620, CS-820 C9060
CS-620, CS-820 C9070
CS-620, CS-820 C9080
CS-620, CS-820 E001
CS-620, CS-820 E010
CS-620, CS-820 E011
CS-620, CS-820 E012
BF-1(B) Centerfold Blade Problem. During initialization the centerfold blade is not detected in the home position within a specified period of time.
DP Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned ON.
DP Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned ON.
DP EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
DP Communication Problem between the DP and SHD. A communication error is detected.
DP Communication Error between the DP and CIS. Reading cannot be performed correctly.
Scan Sys (H) Transmission in progress was cancelled by operator.
Scan Sys (H) Destination computer could not be found during data transmission. (An error occurred that could not be classified more clearly under any error code after E011.) The scanner could not find the computer that was running the personal Address Book.
Scan Sys (H) Transmission was stopped due to problems with the image data itself.
Scan Sys (H) The scanner attempted to transmit image data, but was unable to access the corresponding information in the personal Address Book due to a connection problem.
CS-620, CS-820 E020
CS-620, CS-820 E021
CS-620, CS-820 E022
CS-620, CS-820 E023
CS-620, CS-820 E024 Scan Sys (H) SMTP Authentication error.
CS-620, CS-820 E030
CS-620, CS-820 E031
CS-620, CS-820 E032
CS-620, CS-820 E033
CS-620, CS-820 E034
CS-620, CS-820 E035
Scan Sys (H) An attempt to use the Send E-mail function was made, but the scanner was unable to find the SMTP server.
Scan Sys (H) The destination of the email is listed under the restricted domain names, or is not listed under the permitted domain names.
Scan Sys (H) The mail contained an email address that the SMTP server could not find.
Scan Sys (H) The SMTP server is not operating properly.
Scan Sys (H) The destination computer cannot be found. Either the Scan File Utility is not running or it is already communicating with another scanner.
Scan Sys (H) The scanner attempted to transmit image data, but the registered password did not match the password in the destination computer.
Scan Sys (H) During the scan-to-PC operation, the hard drive on the destination computer ran out of available space.
Scan Sys (H) The versions of the Scan File Utility do not match.
Scan Sys (H) Transmission was not possible because the Scan File Utility is communicating with another scanner
Scan Sys (H) During group transmission, the number of the save folder registered in the Scan File Utility did not match.
CS-620, CS-820 E036
CS-620, CS-820 E039
CS-620, CS-820 E059
CS-620, CS-820 E061
CS-620, CS-820 E080
CS-620, CS-820 E081
CS-620, CS-820 E082
Scan Sys (H) During compression of the scanned image data, the data size went over the maximum limit.
Scan Sys (H) The response received from the destination computer under the Scan-to-PC function was not an appropriate one. Unexpected trouble has occurred in the destination computer.
Scan Sys (H) A command received from the transmitting computer was not an appropriate one. Trouble has occurred in the computer that is running the corresponding personal Address Book.
Scan Sys (H) When selecting the group in the destination computer under either the Send E-mail or Scan to PC functions, some type of trouble has occurred in the information for the registered members of the group.
Scan Sys (H) The FTP server cannot be found.
Scan Sys (H) The FTP server is failed to login.
Scan Sys (H) The storing path is incorrect.
CS-620, CS-820 E083
CS-620, CS-820 E090 Scan Sys (H) POP3 server not found.
CS-620, CS-820 E091
CS-620, CS-820 E093
CS-620, CS-820 E101
CS-620, CS-820 message "Check domain name and host name."
CS-620, CS-820 message
CS-620, CS-820 message "Communication error."
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
Scan Sys (H) The error occurred in the FTP server.
Scan Sys (H) Unable to login to POP3 server. POP3 server user account or password is incorrect.
Scan Sys (H) An error occurred at the POP3 server.
Scan Sys (H) An error has occurred while selecting multiple destinations.
"Check the DB Assistant PC. Contact administrator."
"DB Assistant Server error. Contact administrator."
"DB Assistant Server is in use. Try again later."
"DB Assistant Server version is different. Contact administrator."
"Destination address is not being registered."
CS-620, CS-820 message "Destination PC is in use. Try again later."
CS-620, CS-820 message
CS-620, CS-820 message "Destination PC's system error."
CS-620, CS-820 message "E-mail size exceeds data capacity."
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message "Network scanner system error."CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
"Destination PC's application is out of order."
"Error occurred at FTP Server. Please contact administrator."
"Error occurred at POP3 Server. Please contact administrator."
"No destination address being registered."
"Overflow of original pages. Scanned documents were sent."
"PC's version of personal address list is different. Contact administrator."
"PC of personal address list is in use. Try again later."
"POP3 server not found. Contact Administrator."
"Registration full. You cannot add any more."
"Sender (user) is not registered. Contact administrator."
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
CS-620, CS-820 message
"SMTP Authentication error. Contact administrator."
"The file was not saved. Check the destination PC."
"The path attempted to use for saving does not exist."
"This name is already in use. Input new name again."
"This number is already in use. Input new number again."
"Unable to find destination PC. Check the PC."
"Unable to find FTP server. Contact administrator."
"Unable to find PC of personal address list. Check the PC"
"Unable to find POP3 server. Contact Administrator."
CS-620, CS-820 message
CS-620, CS-820 message "Unable to Log in to the FTP Server."
CS-620, CS-820 message
CS-620, CS-820 message "Unable to use the scanner."
CS-620, CS-820 message "Wrong password."
"Unable to find SMTP server. Contact administrator."
"Unable to Log in to the POP3 Server. Confirm the login account and password for SMTP TX authen."
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
21 Start > Execute > Start.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data: 10871087
Turn power Off/On. If code immediately returns initialize backup data for image processing: 10871087
Start > Engine > Execute > Start. (tech only)
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start > Stop/Clear > 24 > Start > Execute > Start.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
22
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data for scanning: 10871087
Start > SCANNER+DP > Execute > Start. (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
10871087 163 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
10871087 906 Start > Execute > Start
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Service Checks
1) Repl main PWB.
1) Run simulation U21, 2) Repl main PWB.
1) Reseat YC26 @ main PWB & relay PWB, 2) Temporarily run sim U935. Status 10871087 > 935 > Start > select mode (60=MODE 1, 80=MODE 2) > Start > Clear > 1 > Start. (default=MODE 0)
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl main PWB.
1) Reload firmware, 2) Repl EEPROM. 3) Repl engine PWB.
1) Run simulation U022, 2) Repl engine PWB.
1) Replace EEPROMs, 2) Repl engine PWB, 3) Repl main PWB.
1) Replace EEPROMs, 2) Repl engine PWB, 3) Repl main PWB.
1) Reseat YC1 @ main PWB & YC1 @ engine PWB, 2) Repl main PWB, 3) Repl engine PWB.
1) Reseat YC2 @ engine PWB & YC5 @ scanner PWB, 2) Repl main PWB, 3) Repl scanner PWB.
1) Reseat YC9 @ main PWB & YC5 @ printer PWB, 2) Reseat DIMM, 3) Repl printer PWB, 4) Repl main PWB.
1) Repl DIMM, 2) Repl main PWB.
1) Repl main PWB.
1) Reseat YC3 @ main PWB, 2) Reseat network scanner board, 3) Repl network scanner PWB, 4) Repl main PWB.
1) Reseat YC26 @ main PWB & relay PWB, 2) Temporarily run sim U935. Status 10871087 > 935 > Start > select mode (60=MODE 1, 80=MODE 2) > Start > Clear > 1 > Start. (default=MODE 0)
1) Reseat YC6 @ scanner PWB & YC1 @ DP main PWB, 2) Repl DP main PWB.
Reseat YC15 @ engine PWB & YC3 @ side feeder main PWB, 2) Repl engine PWB, 3) Repl side feeder main PWB.
1) Reseat YC14 @ engine PWB & YC4 @ finisher main PWB, 2) Repl engine PWB, 3) Repl finisher main PWB.
1) Reseat YC2 @ engine PWB & YC2 @ duplex PWB, 2) Repl engine PWB, 3) Repl duplex PWB.
1) Reseat YC3 @ engine PWB & YC2 @ deck PWB, 2) Repl engine PWB.
1) Reseat YC4 @ engine PWB & YC2 @ cassette PWB, 2) Repl engine PWB.
1) Reseat YC11 @ engine PWB & HDD connectors, 2) Run U906 (partial reset) & U024 (HDD formatting), 3) Repl HDD harnass, 4) Repl main PWB.
1) Repl side feeder main PWB.
1) Repl finisher main PWB.
1) Repl punch PWB.
1) Repl centerfold unit main PWB.
1) Repl main PWB.
1) Reseat YC5 @ engine PWB & developing unit connector, 2) Reseat developing unit, 3) Repl developing unit, 4) Repl engine PWB.
1) Reseat YC5 @ engine PWB & cleaning unit connector, 2) Reseat cleaning unit, 3) Repl cleaning unit, 4) Repl engine PWB.
1) Reseat lift upper limit switch connector & lift motor 1 connector, 2) Check for lift drive problem, 3) Check for open motor coil. Repl Lift Motor 1, 4) Run sim U031 to test lift upper limit switch. (LIM SW1 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl deck PWB.
1) Reseat lift upper limit switch connector & lift motor 2 connector, 2) Check for lift drive problem, 3) Check for open motor coil. Repl Lift Motor 2, 4) Run sim U031 to test lift upper limit switch. (LIM SW2 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl deck PWB.
1) Reseat lift upper limit switch connector & lift motor 3 connector, 2) Check for lift drive problem, 3) Check for open motor coil. Repl lift motor 3, 4) Run sim U031 to test lift upper limit switch. (LIM SW3 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl cassette PWB.
1) Reseat lift upper limit switch connector & lift motor 4 connector, 2) Check for lift drive problem, 3) Check for open motor coil. Repl lift motor 4, 4) Run sim U031 to test lift upper limit switch. (LIM SW4 is highlighted when ON). If no, replace lift upper limit switch, 5) Repl cassette PWB.
1) Reseat upper limit switch & lift motor connector. 2) Measure +/-24vdc YC5-A12 (SFLM+) to YC6-B11 (safety switch loop-) @ side feeder main PWB while running sim U247 (SDECK LIFT is highlighted when ON). Make sure LUSSW, UCSSW, LLSSW, & RCSSW are off. If voltage absent repl side feeder main PWB. 3) If voltage present with safety switches off, repl SFLM (lift motor).
1) Reseat upper limit switch & lift motor connector. 2) Measure +/-24vdc YC4-1 (-) to YC4-9 (+) @ SF main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl SF main PWB. 3) If DC present measure +/-24vdc YC4-5 (-) to YC4-6 (+) @ SF main PWB while running sim U247 (same as above). If DC absent check safety switches ULSSW, LLSSW, TSSW. If DC present but motor doesn't run repl SFLM (lift motor).
1) Reseat lower limit switch & lift motor connector. 2) Measure +/-24vdc YC5-A12 (SFLM+) to YC6-B11 (safety switch loop-) @ side feeder main PWB while running sim U247 (SDECK LIFT is highlighted when ON). Make sure LUSSW, UCSSW, LLSSW, & RCSSW are off. If voltage absent repl side feeder main PWB. 3) If voltage present with safety switches off, repl SFLM (lift motor).
1) Reseat lower limit switch & lift motor connector. 2) Measure +/-24vdc YC4-1 (-) to YC4-9 (+) @ SF main PWB while running sim U247 (SDECK LIFT is highlighted when ON). If voltage absent repl SF main PWB. 3) If DC present measure +/-24vdc YC4-5 (-) to YC4-6 (+) @ SF main PWB while running sim U247 (same as above). If DC absent check safety switches ULSSW, LLSSW, TSSW. If DC present but motor doesn't run repl SFLM (lift motor).
1) Reseat YC29 @ engine PWB & YC1 @ duplex PWB, 2) Repl duplex side registration motor, 3) Repl duplex PWB.
1) Reseat developing motor connector, 2) Check for drive problems, 3) Repl developing motor, 4) Repl duplex PWB.
1) Reseat YC2 & YC11 on the deck PWB, 2) Check for drive problems, 3) Repl drive motor, 4) Repl deck PWB, 5) Repl engine PWB.
1) Reseat YC5 on the engine PWB, 2) Check for drive problems, 3) Repl cleaning motor, 4) Repl engine PWB.
1) Reseat YC2 & YC4 on the duplex PWB, 2) Check for drive problems, 3) Repl fuser motor, 4) Repl duplex PWB, 5) Repl engine PWB.
1) Reseat YC2 & YC3 @ cassette PWB, & YC4 @ engine PWB, 2) Check for drive problems, 3) Repl transfer motor, 4) Repl cassette PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Repl side feeder drive motor, 3) Repl side feeder main PWB.
1) Check for drive problems, 2) Reseat YC5 @ engine PWB, 3) Repl PTC cleaning motor, 3) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC2, YC5, & YC10 @ scanner PWB, 3) Reseat conn scanner home position switch, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl scanner PWB.
1) Repl scanner PWB.
1) Run simulation U022, 2) Repl main PWB.
1) Reseat YC3, YC4, & YC5 @ scanner PWB, 2) Reseat YC5, YC6, & YC8 @ SHD PWB, 3) Reseat YC1, YC2, & YC3 @ CCD PWB, 4) Reseat conn @ inverter PCB, 5) Adjust position of shading plate, 6) Repl scanner HPS 7) Repl exposure lamp & inverter PWB, 8) Repl scanner PWB, 9) Replace CCD PWB.
1) Reseat YC2 @ DP main PWB, 2) Repl DP inverter PWB, 3) Repl CIS, 4) Repl DP main PWB.
1) Reseat YC5, YC6, & YC8 @ SHD PWB, 2) Reseat YC1, YC2, & YC3 @ CCD PWB, 4) Reseat conn @ inverter PCB, 5) Adjust position of shading plate, 6) Repl scanner HPS 7) Repl exposure lamp & inverter PWB, 8) Repl scanner PWB, 9) Replace CCD PWB (ISU).
1) Repl DP inverter PWB, 2) Repl CIS, 3) Repl DP main PWB.
1) Reseat YC3 @ scanner PWB & YC4 @ SHD PWB, 2) Pinout harnass, 3) Repl scanner PWB, 4) Repl SHD PWB.
1) Reseat laser unit connectors, 2) Measure 24vdc on YC17-1 @ engine PWB to frame ground. If present, repl laser unit, 3) If absent, repl engine PWB.
1) Reseat laser unit connectors, 2) Measure 24vdc on YC17-1 @ engine PWB to frame ground. If present, repl laser unit, 3) If absent, repl engine PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC8 @ main PWB & @ laser unit, 2) Pinout harnass, 3) Repl laser unit, 4) Repl main PWB.
1) Reseat YC7 @ engine PWB, 2) Repl main charger unit, 3) Repl high voltage PWB.
1) Reseat YC5 @ engine PWB, 2) Repl drum surface potential sensor, 3) Repl high voltage PWB, 4) Repl engine PWB.
1) Reseat YC5 @ engine PWB, 2) Repl drum surface potential sensor, 3) Repl high voltage PWB.
1) Repl main charger wire, 2) Clean grid or main charger shield, 3) Repl drum surface potential sensor, 4) Repl high voltage PWB, 5) Repl engine PWB.
1) Repl drum surface potential sensor, 2) Repl high voltage PWB, 3) Repl drum, 4) Repl engine PWB.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters L, M, & S, 4) Repl AC PS PWB, 5) Repl engine PWB.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Replace thermistor M & S, 3) Repl engine PWB.
1) Install the correct finisher.
1) Check that thermistor M & S are contacting heat roller & clean, 2) Replace thermistor M & S, 3) Repl engine PWB, 4) Repl AC PS PWB
1) Check that thermistor M & S are contacting heat roller & clean, 2) Check thermal switch, 3) Check fixing heaters L, M, & S, 4) Repl AC PS PWB, 5) Repl engine PWB.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC11 @ engine PWB & YC6 @ DC PS PWB, 3) If zero-cross signal is not output from YC6-3 @ DC PS PWB, repl DC PS PWB, 3) If zero-cross signal is detected from YC6-3 @ DC PS PWB (and C6400), repl engine PWB.
1) Reseat YC23 @ engine PWB, 2) Repl developing humidity sensor, 3) Repl engine PWB.
1) Reseat YC23 @ engine PWB, 2) Repl developing humidity sensor, 3) Repl engine PWB.
1) Reseat YC2 & YC5 @ deck PWB & YC3 @ engine PWB, 2) Pinout harnass, 3) Replace toner level detection sensor.
1) Reseat YC13 @ engine PWB, 2) Pinout harnass, 3) Repl developing humidity sensor.
1) Reseat YC13 @ engine PWB, 2) Pinout harnass, 3) Repl developing humidity sensor.
1) Reseat YC14 @ finisher main PWB, 2) Check for drive problems, 3) Repl paper conveying motor, 4) Repl finisher main PWB.
1) Reseat YC13 @ finisher main PWB & YC1 @ punch PWB, 2) Check for drive problems, 3) Repl punch motor, 4) Repl finisher main PWB.
1) Reinsert intermediate tray (check for damaged catches), 2) Correct the phase of the upper paper conveying belt(?), 3) Reseat the upper paper conveying belt HPS connector. 4) Repl upper paper conveying belt HPS, 5) Repl upper paper conveying belt motor, 6) Repl finisher main PWB.
1) Reinsert intermediate tray (check for damaged catches), 2) Correct the phase of the lower paper conveying belt(?), 3) Reseat the lower paper conveying belt HPS connector. 4) Repl lower paper conveying belt HPS, 5) Repl lower paper conveying belt motor, 6) Repl finisher main PWB.
1) Reseat sensor & main tray elevator motor connectors, 2) Repl tray sensors 3) Repl main tray elevator motor, 4) Repl finisher main PWB.
1) Reseat sensor & multi-job tray elevator motor connectors, 2) Repl tray sensor 3) Repl multi-job tray elevator motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front upper side registration home position sensor, 3) Repl front upper side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear upper side registration home position sensor, 3) Repl rear upper side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl lower side registration home position sensor, 3) Repl lower side registration guide motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front stapler home position sensor, 3) Repl front stapler motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl front clincher home position sensor, 3) Repl front clincher motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear stapler home position sensor, 3) Repl rear stapler motor, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl rear clincher home position sensor, 3) Repl rear clincher motor, 4) Repl finisher main PWB.
1) Reseat centerfold set switch connector, 2) Repl centerfold unit set switch, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat sensor & motor connectors, 2) Repl side registration guide home position sensor, 3) Repl side registration guide motor, 4) Repl centerfold main PWB.
1) Reseat sensor & motor connectors, 2) Repl centering plate home position sensor, 3) Repl centering plate motor, 4) Repl centerfold main PWB.
Try to perform the operation again.
1) Reseat sensor & motor connectors, 2) Repl centerfold blade home position sensor, 3) Repl centerfold blade motor, 4) Repl centerfold main PWB.
1) Reseat sensor & motor connectors, 2) Repl DP lift upper limit switch, 3) Repl DP lift motor, 4) Repl DP main PWB.
1) Reseat sensor & motor connectors, 2) Repl DP lift lower limit switch, 3) Repl DP lift motor, 4) Repl DP main PWB.
1) Repl DP main PWB, 2) Contact Service Administration Division.
1) Check all connectors @ SHD PWB, 2) Pinout connectors/harnass, 3) Repl SHD PWB, 4) Repl DP main PWB.
1) Check all connectors @ CIS, 2) Pinout connectors/harnass, 3) Repl CIS.
Check to make sure that the destination computer is operating properly. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check to make sure that the computer that is running the personal Address Book is running properly.
Check the versions of the Scan File Utility.
Check the Scan File Utility Settings.
Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly. Check with the network administrator to find out whether the SMTP server is working properly.
Check the restricted and/or permitted domain names, and adjust the settings as necessary. Check to make sure that the destination email address was entered correctly.
Check to make sure that the destination email address was entered correctly.
Check with your network administrator to find out whether the SMTP server is working properly.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
Check to make sure that the Scan File Utility is running properly in that computer, or whether it is already connected to another scanner. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check the password that is set in the destination computer.
Increase the available space on the destination computer's hard drive, then try the operation again.
Try to perform the operation again after the connection to the other scanner is completed.
Perform any or all of the following procedures in order to lower the amount of data and then try scanning and transmission operation again: 1) lower the resolution of the image data. 2) Change the image quality setting to OCR. 3) Lower the number of documents (pages) that are being scanned at one time.
Check to make sure that the Scan File Utility in the destination computer is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, running in the destination computer. If the trouble is with the destination computer, fix the problem.
Check to make sure that the personal Address Book is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, also running on the computer that is running the persoal Address Book. If the trouble is with the computer that is running the personal Address Book, fix that problem.
Check the computer of each group member as necessary and, if there is trouble in any of those computers, fix that problem.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
Verify POP3 server settings.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
Check that the POP3 server is running properly. Confirm that there is no link fault by checking whether the network cable is properly connected.
Change the POP3 server user account or password.
Check each error and fix the corresponding problems.
The scanner's domain name and host name have not been registered properly. Check the correct domain name and host name. (Refer to "(3) Making settings from the touch panel".)
The DB Assistant cannot be found. Make sure that the DB Assistant is running properly on the computer on which it is installed.
If you are using the Scan to PC function, check the status of the destination computer and then try the operation again. If you are using the Send E-mail function, check to make sure that the SMTP server is running, or consult with the network administrator. If you are using the DB Assistant function, check to make sure that the DB Assistant is installed on the computer.
Communication could not be continued because an error occurred with the DB Assistant or with the computer on which it is installed.
DB Assistant is currently communicating with another scanner. Wait for a while and then try the operation again.
The versions of the DB Assistant do not match. Consult the network administrator.
The entered number is not appropriate. Check the correct number and enter it again.
Verify POP3 server settings.
Restart the scanner.
The destination computer and the scanner are currently communicating. Wait for a while and then try the operation again.
Check to make sure that the Scan File Utility is running in the destination computer.
Check the status of the destination computer and then try the operation again.
Reduce the number of pages being transmited, or lower the scanning resolution, and try to transmit again.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
The selected destination is not registered. Register that destination or select another one.
The number of scanned documents exceeds 999, the maximum that can be transmitted at one time. Transmit any further pages separately. When transmitting under settings such as "two-sided" or "booklet", there may be a case where only 998 pages can be scanned and transmitted.
The versions of the Address Book do not match. Consult your network administrator.
The designated AddressBook and the scanner are currently communicating. Wait a while and then try the operation again.
Confirm that the network cable is properly connected. Start the POP3 server.
Delete any unnecessary items and try the procedure again.
User Number 001 is not registered in the "Select sender name" List of this scanner. First register a user under that number or turn the "Selection of senders (users)" setting OFF, then select another user.
Register a different name.
Register a different number.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
If the amount of data exceeds the hard disk capacity as registered in the Scan File Utility on the destination computer, increase the available space on your computer's hard disk and then try the operation again. If data with the same file name has been sent from more than one scanner at a time, the data cannot be saved. Wait for a while and then try the operation again, or change the file name.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
There is a problem at your computer. Check to make sure that the Scan File Utility is running and the computer is able to receive data.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
If the Address Book software is not running on your computer, start it up. If it is already running, make sure that your computer is connected properly to the network and the network cable is connected properly to the Scanner NIC card.
Verify the POP3 user account and password are correct.
Enter the correct password.
Check to make sure the network cable connected securely and properly. If the message appears immediately after turning the scanner ON, wait approximately 2 minutes while the scanner NIC boots up. Check to make sure that the SMTP server is running, or consult with your network administrator.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
Verify the POP3 user account and password are correct.
Check to make sure that the network cable is connected securely and properly. If the message appears immediately after turning the scanner On, wait approximately 2 minutes while the scanner NIC boots up.
Model Error Code DescriptionC0030
C0070
C0100
C0110
C0150
C0160
C0170
C0180
C0210
C0220
C0240
CS-C2525E (2JL), C3225E (2JJ), C3232E (2JG), C4035E (2JD)
Fax Control PWB Problem. Processing with fax software is disabled due to software or hardware issues.
CS-C2525E, C3225E, C3232E, C4035E
Abnormal Detection of Fax Control PWB Incompatability. In the initial communication with the fax control PWB , any normal communication command is not transmitted.
CS-C2525E, C3225E, C3232E, C4035E
Main PWB Backup Memory Device Problem. Writing or erasing has not completed even after a certain time.
CS-C2525E, C3225E, C3232E, C4035E
Backup Memory Data Problem. Data in the specified area of the backup memory does not match the specified values.
CS-C2525E, C3225E, C3232E, C4035E
Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read. An error occurs in the control area deletion.
CS-C2525E, C3225E, C3232E, C4035E
Engine PWB EEPROM Backup Memory Data Problem. Data for backup data check is changed at the check after startup.
CS-C2525E, C3225E, C3232E, C4035E
Copy Counts Problem. A checksum error is detected in the main and sub backup memories for copy counters.
CS-C2525E, C3225E, C3232E, C4035E
Backup Memory Data Problem. Backup data on the main PWB has broken.
CS-C2525E, C3225E, C3232E, C4035E
CPU Communication Problem. There is no reply after (3) tries at communication.
CS-C2525E, C3225E, C3232E, C4035E
Communication Problem Between The Scanner & Main PWBs. There is no reply after (6) tries at communication.
CS-C2525E, C3225E, C3232E, C4035E
Printer PWB Communication Problem. The printer PWB does not respond 120 sec after the power is turned ON.
C0250
C0280
C0410
C0420
C0440
C0610
C0630
C0640 Hard Disk Drive cannot be accessed.
CS-C2525E, C3225E, C3232E, C4035E
Network Scanner PWB Communication Problem. Network scanner card does not respond to alive command transmitted once every 30 sec (3) consecutive times or more, or does not respond to communication command after 75 sec or more.
CS-C2525E, C3225E, C3232E, C4035E
Communication Problem between Fax Control PWB & Main PWB. Key required command is not received from fax control PWB after Status Change signal @ main PWB remains ON exceeding (1) minute. 1st occurence: fax resets. 2nd occurence: C0280. The FAX_READY signal remains fake exceeding 6 sec. 1st occurence: fax resets. 2nd occurence: C0280.
CS-C2525E, C3225E, C3232E, C4035E
DP Communication Problem. There is no reply after 10 retires at communication or a communication error occurs.
CS-C2525E, C3225E, C3232E, C4035E
Optional Paper Feeder Communication Error. A communication error from the paper feeder is detected 10 times in succession.
CS-C2525E, C3225E, C3232E, C4035E
Document Finisher Communication Problem. A communication error from document finisher is detected 10 times in succession.
CS-C2525E, C3225E, C3232E, C4035E
Bitmap Problem. The main PWB DIMM does not operate correctly.
CS-C2525E, C3225E, C3232E, C4035E
DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
CS-C2525E, C3225E, C3232E, C4035E
C0800
C0820
C0830
C0840
C0860
C0870
C0880
C0890
C0920
CS-C2525E, C3225E, C3232E, C4035E
Image processing problem. JAM05 is detected twice.
CS-C2525E, C3225E, C3232E, C4035E
Fax Control PWB CG ROM Checksum Error. A checksum error occurred with CG ROM data of the fax control PWB.
CS-C2525E, C3225E, C3232E, C4035E
Fax Control PWB Flash Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
CS-C2525E, C3225E, C3232E, C4035E
Faults of RTC. The time is judged to go back based on the comparison of RTC time and the current time, or five years or more have passed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Control PWB Software Switch Checksum Error. A checksom error occurred with the software switch value of the fax control PWB.
CS-C2525E, C3225E, C3232E, C4035E
Fax Control PWB to Main PWB High Capacity Data Transfer Problem. High capacity data transfer between fax control PWB and scanner MIP PWB was not normally performed after 10 retries.
CS-C2525E, C3225E, C3232E, C4035E
Fax PWB Program Archive Problem. At initialization the compressed program in the flash ROM on the fax control PWB was now successfully decompressed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Control PWB CG FONT Archive Problem. At initialization the compressed CG Font in the flash ROM on the fax control PWB was now successfully decompressed.
CS-C2525E, C3225E, C3232E, C4035E
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of the fax control PWB.
C1010
C1020
C1030
C1040
C1100
C1110
C1120
CS-C2525E, C3225E, C3232E, C4035E
Cassette #1 Lift Motor Error. When cassette 1 is inserted, lift limit switch 1 does not turn on within 12 sec of lift motor 1 turning On.
CS-C2525E, C3225E, C3232E, C4035E
Cassette #2 Lift Motor Error. When cassette 2 is inserted, lift limit switch 2 does not turn on within 12 sec of lift motor 2 turning On.
CS-C2525E, C3225E, C3232E, C4035E
PF-710 Optional Cassette #3 Lift Motor Error. When cassette 3 is inserted, lift limit switch 1 does not turn on within 12 sec of lift motor 1 turning On. Lift overcurrent protective monitor signal is detected exceeding 500ms during driving the motor, except during the first 1 second of operation.
CS-C2525E, C3225E, C3232E, C4035E
PF-710 Optional Cassette #4 Lift Motor Error. When cassette 4 is inserted, lift limit switch 2 does not turn on within 12 sec of lift motor 2 turning On. Lift overcurrent protective monitor signal is detected exceeding 500ms during driving the motor, except during the first 1 second of operation.
CS-C2525E, C3225E, C3232E, C4035E
PF-750 (Left) Lift Motor 1 Error. Exceeds 1 second overcurrent.
CS-C2525E, C3225E, C3232E, C4035E
PF-750 (Right) Lift Motor 2 Error. Exceeds 1 second overcurrent.
CS-C2525E, C3225E, C3232E, C4035E
PF-750 (Left) Lift Motor 1 Position Problem. PF switch 1 remains off after 30 seconds of motor operation.
C1130
C1900
C1950
C2101
C2102
C2201
C2202
C2203
CS-C2525E, C3225E, C3232E, C4035E
PF-750 (Right) Lift Motor 2 Position Problem. PF switch 2 remains off after 30 seconds of motor operation.
CS-C2525E, C3225E, C3232E, C4035E
PF-710 EEPROM error. Write data & Read data are not in agreement three times consecutively.
CS-C2525E, C3225E, C3232E, C4035E
Transfer Belt Unit EEPROM Error. Read & Write data does not match.
CS-C2525E, C3225E, C3232E, C4035E
Paper Feed/Developing Motor BK Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Developing Motor CMY Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Drum Motor BK Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Drum Motor C Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Drum Motor M Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
C2204
C2300
C2400
C2500
C2600
C2600
C2810
CS-C2525E, C3225E, C3232E, C4035E
Drum Motor Y Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Fuser Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
Eject Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
MP Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
CS-C2525E, C3225E, C3232E, C4035E
PF-710 Drive Motor Error. Lock signal exceeds 500ms.
CS-C2525E, C3225E, C3232E, C4035E
PF-750 Paper Conveying Motor Error. Lock signal exceeds 450ms.
CS-C2525E, C3225E, C3232E, C4035E
Waste Toner Motor Error. The rated speed achievement signal does not go low within 5 sec of activation. The RSA signals stays high every other 5 sec after the machine is stabilized.
C3100
C3200
C3300
C3500
C3900
C3910
C4000
C4010
C4100
C4200
C5101
CS-C2525E, C3225E, C3232E, C4035E
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
CS-C2525E, C3225E, C3232E, C4035E
Exposure Lamp Problem. Exposure lamp is not turned ON when starting the copy.
CS-C2525E, C3225E, C3232E, C4035E
Optical System (AGC) Problem. After AGC correct input is not obtained at the CCD.
CS-C2525E, C3225E, C3232E, C4035E
Communication Error Between Scanner and SHD.
CS-C2525E, C3225E, C3232E, C4035E
Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match.
CS-C2525E, C3225E, C3232E, C4035E
Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
CS-C2525E, C3225E, C3232E, C4035E
Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
CS-C2525E, C3225E, C3232E, C4035E
Polygon Motor Steady-State Problem. The rated achievement signal turns to high every other 5 sec after polygon motor stabilization.
CS-C2525E, C3225E, C3232E, C4035E
BD Initialization Problem. At initialization, ASIC of the engine PWB detects a beam detect error for 200ms.
CS-C2525E, C3225E, C3232E, C4035E
BD Steady-State Problem. ASIC of the engine PWB detects a beam detect error for 200ms, after polygon motor stabilization.
CS-C2525E, C3225E, C3232E, C4035E
Main High Voltage BK Error. Abnormality of the BK charge roller is detected during Vpp adjustment.
C5102
C5103
C5104
C5301
C5302
C5303
C5304
C6000
C6010
C6020
CS-C2525E, C3225E, C3232E, C4035E
Main High Voltage C Error. Abnormality of the C charge roller is detected during Vpp adjustment.
CS-C2525E, C3225E, C3232E, C4035E
Main High Voltage M Error. Abnormality of the M charge roller is detected during Vpp adjustment.
CS-C2525E, C3225E, C3232E, C4035E
Main High Voltage Y Error. Abnormality of the Y charge roller is detected during Vpp adjustment.
CS-C2525E, C3225E, C3232E, C4035E
Cleaning Lamp BK Break Error. While the cleaning lamp BK signal is On, the break detection signal is detected 5 times for 10ms.
CS-C2525E, C3225E, C3232E, C4035E
Cleaning Lamp C Break Error. While the cleaning lamp C signal is On, the break detection signal is detected 5 times for 10ms.
CS-C2525E, C3225E, C3232E, C4035E
Cleaning Lamp M Break Error. While the cleaning lamp M signal is On, the break detection signal is detected 5 times for 10ms.
CS-C2525E, C3225E, C3232E, C4035E
Cleaning Lamp Y Break Error. While the cleaning lamp Y signal is On, the break detection signal is detected 5 times for 10ms.
CS-C2525E, C3225E, C3232E, C4035E
Fuser Heater 1/2 Break. Thermistor1 detected less than 75C/167F for 30 sec during warmup. Thermistor1 detected 40C/104F for 5 sec during warmup. Thermistor3 detected less than 90C/194F for 30 sec during warmup. Thermistor3 detected less than 160C/320F for 90 sec during warmup. Thermistor3 detected less than 140C/284F for 5 sec during standby.
CS-C2525E, C3225E, C3232E, C4035E
Abnormally High Fuser Thermistor Temperature. The fuser abnormally high signal is detected for 60 sec or more.
CS-C2525E, C3225E, C3232E, C4035E
Abnormally High Fuser Thermistor 1/3 Temperature. The fuser temperature exceeds 240C/464F.
C6030
C6050
C6100
C6120
C6130
C6400
C7000
C7101
C7102
C7103
CS-C2525E, C3225E, C3232E, C4035E
Fixing Thermistor 1/3 Break Error. Thermistor1 detected 40C/104F or less during warmup exceeding 10 sec. Thermistor3 detected 40C/104F or less during warmup.
CS-C2525E, C3225E, C3232E, C4035E
Abnormally Low Fuser Thermistor3 Temperature. Thermistor3 detected less than 100C/212F for 1 sec continuously during copying.
CS-C2525E, C3225E, C3232E, C4035E
Fuser Heater 3 Break. Thermistor2 detected less than 100C/212F for 120 sec during driving. Thermistor2 detected less than 150C/302F for 300 sec during driving. Thermistor2 detected less than 100C/212F for 5 sec during driving.
CS-C2525E, C3225E, C3232E, C4035E
Abnormal High Fuser Thermistor2 Temperature. The fuser temperature exceeds 190C/374F.
CS-C2525E, C3225E, C3232E, C4035E
Fuser Thermistor2 Break Error. Thermistor2 detected less than 40C/104F during driving. Temperature difference between thermistor1 and thermistor3 is 100C/212F or more.
CS-C2525E, C3225E, C3232E, C4035E
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
CS-C2525E, C3225E, C3232E, C4035E
Toner Motor Problem. The rated speed achievement signal does not go low within 5 sec of activation. The RSA signals stays high every other 5 sec after the machine is stabilized.
CS-C2525E, C3225E, C3232E, C4035E
Toner Sensor BK Problem. Toner sensor output values are outside the desired criterion (78 < X < 944) for 3 sec.
CS-C2525E, C3225E, C3232E, C4035E
Toner Sensor C Problem. Toner sensor output values are outside the desired criterion (78 < X < 944) for 3 sec.
CS-C2525E, C3225E, C3232E, C4035E
Toner Sensor M Problem. Toner sensor output values are outside the desired criterion (78 < X < 944) for 3 sec.
C7104
C7200
C7210
C7220
C7230
C7240
C7250
C7401
C7402
C7403
C7404
C7411
C7412
CS-C2525E, C3225E, C3232E, C4035E
Toner Sensor Y Problem. Toner sensor output values are outside the desired criterion (78 < X < 944) for 3 sec.
CS-C2525E, C3225E, C3232E, C4035E
Broken Internal Thermistor Wire. An abnormal value is detected in the input data to inner temperature sensor 1.
CS-C2525E, C3225E, C3232E, C4035E
Short-Circuited Internal Thermistor. An abnormal value is detected in the input data to inner temperature sensor 1.
CS-C2525E, C3225E, C3232E, C4035E
Broken Internal Thermistor2 Wire. An abnormal value is detected in the input data to inner temperature sensor 2.
CS-C2525E, C3225E, C3232E, C4035E
Short-Circuited Internal Thermistor2. An abnormal value is detected in the input data to inner temperature sensor 2.
CS-C2525E, C3225E, C3232E, C4035E
Broken Internal Thermistor3 Wire. An abnormal value is detected in the input data to inner temperature sensor 3.
CS-C2525E, C3225E, C3232E, C4035E
Short-Circuited Internal Thermistor3. An abnormal value is detected in the input data to inner temperature sensor 3.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit BK Type Mismatch Problem. Absence of the developing unit BK is detected.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit C Type Mismatch Problem. Absence of the developing unit C is detected.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit M Type Mismatch Problem. Absence of the developing unit M is detected.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit Y Type Mismatch Problem. Absence of the developing unit Y is detected.
CS-C2525E, C3225E, C3232E, C4035E
Drum Unit BK Type Mismatch Problem. Absence of the drum unit BK is detected.
CS-C2525E, C3225E, C3232E, C4035E
Drum Unit C Type Mismatch Problem. Absence of the drum unit C is detected.
C7413
C7414
C7420
C7800
C7810
C7901
C7902
C7903
C7904
C7911
C7912
C7913
C7914
C8020
CS-C2525E, C3225E, C3232E, C4035E
Drum Unit M Type Mismatch Problem. Absence of the drum unit M is detected.
CS-C2525E, C3225E, C3232E, C4035E
Drum Unit Y Type Mismatch Problem. Absence of the drum unit Y is detected.
CS-C2525E, C3225E, C3232E, C4035E
Transfer Belt Unit Type Mismatch Problem. Absence of the transfer belt unit is detected.
CS-C2525E, C3225E, C3232E, C4035E
Broken External Thermistor Wire. An abnormal value is detected in the input data to outer temperature sensor.
CS-C2525E, C3225E, C3232E, C4035E
Short-Circuited External Thermistor. An abnormal value is detected in the input data to outer temperature sensor.
CS-C2525E, C3225E, C3232E, C4035E
Drum BK EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Drum C EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Drum M EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Drum Y EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit BK EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit C EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit M EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
Developing Unit Y EEPROM Error. Reading or writing to the EEPROM cannot be performed.
CS-C2525E, C3225E, C3232E, C4035E
PH-5A Punch Motor Problem. The lock signal of the punch motor is detected exceeding 500ms during punch motor activation.
C8030
C8050
C8060
C8070
C8140
C8140
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects ON condition.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 1.5 sec.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray upper surface detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray upper surface detection sensor is not detected as Off within 20 sec of main tray decending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray decending. Main tray upper limit detection sensor or main tray upper surface detection sensor remain On for 2 sec or more during main tray ascent.
CS-C2525E, C3225E, C3232E, C4035E
DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec of tray elevation motor activation.
C8170
C8170
C8180
C8210
C8210
C8220
C8230
C8300
C8310
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
CS-C2525E, C3225E, C3232E, C4035E
DF-730 Adjustment Motor Problem. Registration home position can not be detect to be On or Off within 125ms of registration motor activation. Registration home position can not be detected to be On within 710ms of registration motor activation.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Stapler Shift Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
CS-C2525E, C3225E, C3232E, C4035E
DF-730 Stapler Problem. Home position is not detected within 1 sec of activation.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Stapler Shift Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Stapler Motor Problem. Jam 82 is indicated.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
C8320
C8330
C8340
C8350
C8360
C8440
C8460
C8500
C8510
C8900
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Staple Motor Problem. Jam 89.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
CS-C2525E, C3225E, C3232E, C4035E
DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
CS-C2525E, C3225E, C3232E, C4035E
DF-730 EEPROM Problem. Read and write data does not match (3) times in succession.
CS-C2525E, C3225E, C3232E, C4035E
MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox.
CS-C2525E, C3225E, C3232E, C4035E
MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.
CS-C2525E, C3225E, C3232E, C4035E
DF-710 Backup Memory Data Problem. Read and write data does not match (3) times in succession.
C8910
C8920
C8930
C9060
C9500 No information provided
C9510 No information provided
C9520 No information provided
C9530 No information provided
C9540 No information provided
C9550 No information provided
E001
E010
E011
CS-C2525E, C3225E, C3232E, C4035E
PH-5A Backup Memory Data Problem. Read and write data does not match (3) times in succession.
CS-C2525E, C3225E, C3232E, C4035E
MT-710 Backup Memory Data Problem. Read and write data does not match (3) times in succession.
CS-C2525E, C3225E, C3232E, C4035E
BF-710 Backup Memory Data Problem. Read and write data does not match.
CS-C2525E, C3225E, C3232E, C4035E
DP-710 EEPROM Error. Read and write data does not match.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
Transmission in progress was cancelled by operator.
CS-C2525E, C3225E, C3232E, C4035E
Destination computer could not be found during data transmission. (An error occurred that could not be classified more clearly under any error code after E011.) The scanner could not find the computer that was running the personal Address Book.
CS-C2525E, C3225E, C3232E, C4035E
Transmission was stopped due to problems with the image data itself.
E012
E020
E021
E022
E023
E024 SMTP Authentication error.
E030
E031
E032
E033
CS-C2525E, C3225E, C3232E, C4035E
The scanner attempted to transmit image data, but was unable to access the corresponding information in the personal Address Book due to a connection problem.
CS-C2525E, C3225E, C3232E, C4035E
An attempt to use the Send E-mail function was made, but the scanner was unable to find the SMTP server.
CS-C2525E, C3225E, C3232E, C4035E
The destination of the email is listed under the restricted domain names, or is not listed under the permitted domain names.
CS-C2525E, C3225E, C3232E, C4035E
The mail contained an email address that the SMTP server could not find.
CS-C2525E, C3225E, C3232E, C4035E
The SMTP server is not operating properly.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
The destination computer cannot be found. Either the Scan File Utility is not running or it is already communicating with another scanner.
CS-C2525E, C3225E, C3232E, C4035E
The scanner attempted to transmit image data, but the registered password did not match the password in the destination computer.
CS-C2525E, C3225E, C3232E, C4035E
During the scan-to-PC operation, the hard drive on the destination computer ran out of available space.
CS-C2525E, C3225E, C3232E, C4035E
The versions of the Scan File Utility do not match.
E034
E035
E036
E039
E059
E061
E080 The FTP server cannot be found.
CS-C2525E, C3225E, C3232E, C4035E
Transmission was not possible because the Scan File Utility is communicating with another scanner. Send failed.
CS-C2525E, C3225E, C3232E, C4035E
During group transmission, the number of the save folder registered in the Scan File Utility did not match.
CS-C2525E, C3225E, C3232E, C4035E
During compression of the scanned image data, the data size went over the maximum limit.
CS-C2525E, C3225E, C3232E, C4035E
The response received from the destination computer under the Scan-to-PC function was not an appropriate one. Unexpected trouble has occurred in the destination computer.
CS-C2525E, C3225E, C3232E, C4035E
A command received from the transmitting computer was not an appropriate one. Trouble has occurred in the computer that is running the corresponding personal Address Book.
CS-C2525E, C3225E, C3232E, C4035E
When selecting the group in the destination computer under either the Send E-mail or Scan to PC functions, some type of trouble has occurred in the information for the registered members of the group.
CS-C2525E, C3225E, C3232E, C4035E
E081 The FTP server is failed to login.
E082 The storing path is incorrect.
E083 The error occurred in the FTP server.
E090 POP3 server not found.
E091
E092 Error occurred at POP3 server.
E101
E00000 or U00000
E00100 or U00100
E00200 or U00200
E00300 or U00300
E00420 or U00420
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
Unable to login to POP3 server-POP3 server user account or password incorrect.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
An error has occurred while selecting multiple destinations.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: No response or line busy after the set number of redials.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Recording paper on the destination unit has run out during reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421
E00430 or U00430
E00430 or U00430
E00431 or U00431
E00431 or U00431
E00432 or U00432
E00432 or U00432
E00433 or U00433
E00433 or U00433
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434
E00435 or U00435
E00435 or U00435
E00440 or U00440
E00440 or U00440
E00440 or U00440
E00441 or U00441
E00450 or U00450
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460
E00460 or U00460
E00462 or U00462
E00500 or U00500
E00600 or U00600
E00601 or U00601
E00602 or U00602
E00603 or U00603
E00604 or U00604
E00610 or U00610
E00611 or U00611
E00613 or U00613
E00614 or U00614
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: The document processor cover is open.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Document jam or the document length exceeds the maximum.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Image scanning section problem
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: No document feed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Recording section cover open.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Recording paper jam.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Image writing section problem.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615
E00620 or U00620
E00622 or U00622
E00655 or U00655
E00656 or U00656
E00670 or U00670
E00677 or U00677
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700
E00800 or U00800
E00810 or U00810
E00900 or U00900
E00910 or U00910
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Empty of recording paper.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Copier fixing unit problem.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Copier drive motor problem.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: CTS was not activated after RTS due to a modem error.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Power was cut off during communication.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: There was no file to transmit in the memory transmission mode.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
E01000 or U01000
E01000 or U01000
E01001 or U01001
E01010 or U01010
E01011 or U01011
E01012 or U01012
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01013 or U01013
E01014 or U01014
E01015 or U01015
E01016 or U01016
E01017 or U01017
E01018 or U01018
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
E01019 or U01019
E01020 or U01020
E01021 or U01021
E01022 or U01022
E01023 or U01023
E01024 or U01024
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025
E01026 or U01026
E01027 or U01027
E01028 or U01028
E01040 or U01040
E01041 or U01041
E01042 or U01042
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043
E01044 or U01044
E010x45 or U01045
E01046 or U01046
E01047 or U01047
E01048 or U01048
E01049 or U01049
E01050 or U01050
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051
E01052 or U01052
E01053 or U01053
E01054 or U01054
E01055 or U01055
E01056 or U01056
E01057 or U01057
E01070 or U01070
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071
E01072 or U01072
E01073 or U01073
E01080 or U01080
E01091 or U01091
E01092 or U01092
E01100 or U01100
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brak in loop current was detected during transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
E01102 or U01102
E01110 or U01110
E01111 or U01111
E01112 or U01112
E01113 or U01113
E01114 or U01114
E01115 or U01115
E01116 or U01116
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117
E01118 or U01118
E01119 or U01119
E01120 or U01120
E01121 or U01121
E01122 or U01122
E01123 or U01123
E01124 or U01124
E01125 or U01125
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126
E01127 or U01127
E01128 or U01128
E01129 or U01129
E01140 or U01140
E01141 or U01141
E01142 or U01142
E01143 or U01143
E01144 or U01144
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145
E01146 or U01146
E01147 or U01147
E01148 or U01148
E01149 or U01149
E01150 or U01150
E01151 or U01151
E01152 or U01152
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153
E01154 or U01154
E01155 or U01155
E01160 or U01160
E01161 or U01161
E01162 or U01162
E01163 or U01163
E01164 or U01164
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
E01170 or U01170
E01172 or U01172
E01191 or U01191
E01199 or U01199
E01400 or U01400
E01500 or U01500
E01600 or U01600
E01700 or U01700
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: An invalid one-touch key was specified during communication.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred when calling in V.8 mode.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred when called in V.8 mode.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
E01720 or U01720
E01721 or U01721
E01800 or U01800
E01810 or U01810
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820
E02000 or U02000
E02100 or U02100
E02200 or U02200
E02200 or U02200
E02200 or U02200
E02303 or U02303
E02304 or U02304
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in he period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected beofre a correct DNL signal was received.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
E02400 or U02400
E03000 or U03000
E03100 or U03100
E03200 or U03200
E03200 or U03200
E03300 or U03300
E03300 or U03300
E03400 or U03400
E03500 or U03500
E03500 or U03500
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: No document was present in the destination unit when polling reception started.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500
E03600 or U03600
E03600 or U03600
E03700 or U03700
E03700 or U03700
E04000 or U04000
E04000 or U04000
E04000 or U04000
E04100 or U04100
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: The destination was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: The destination was being accessed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100
E04200 or U04200
E04300 or U04300
E04400 or U04400
E04401 or U04401
E04500 or U04500
E05000 or U05000
E05100 or U05100
E05200 or U05200
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300
E09000 or U09000
E12000 or U12000
E12000 or U12000
E12100 or U12100
E14000 or U14000
E14000 or U14000
E14100 or U14100
E14100 or U14100
E19000 or U19000
E19100 or U19100
E19200 or U19200
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: In subaddress-based relay reception memory overflowed.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed during confidential reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed during memory reception.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory overflowed in the destination unit during transmission.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300
E19400 or U19400
"Account ID mismatch."
Is the indicated cassette out of paper?
"Add toner. [C][M][Y][K]" Toner is empty for the indicated color.
"Call service." An error has occurred when printing.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
CS-C2525E, C3225E, C3232E, C4035E
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
CS-C2525E, C3225E, C3232E, C4035E
No matching ID code found when printing. Verify the registered ID code sent in the print driver.
CS-C2525E, C3225E, C3232E, C4035E
"Add paper in cassette #."
CS-C2525E, C3225E, C3232E, C4035E
"Add paper to the multi-purpose tray.
Has all the paper on the MP tray been fed?
CS-C2525E, C3225E, C3232E, C4035E
"Add paper to the multi-purpose tray. ## size."
Is the paper of the specified size loaded in the multipurpose tray?
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Cannot combine these functions."
A specific function or accessory may be disabled due to an error condition that has instituted Partial Operation Control.
CS-C2525E, C3225E, C3232E, C4035E
"Cannot combine these functions."
Can the specified copy functions be used with the selected exposure settings?
CS-C2525E, C3225E, C3232E, C4035E
"Cannot copy this paper type."
Can the specified copy functions be used with the selected paper type?
CS-C2525E, C3225E, C3232E, C4035E
"Cannot offset this paper size."
Is a paper size not supported by offset mode loaded? (11x17, legal, statementR, A3, B4, A5R, B6R, Folio, or 8K).
CS-C2525E, C3225E, C3232E, C4035E
"Cannot punch this paper type."
Did you select a paper type that cannot be punched?
CS-C2525E, C3225E, C3232E, C4035E
"Cannot punch this size."
Is punching available for the size of the loaded paper?
Is poster enabled?
Is poster enabled?
"Check paper size." Is the specified size paper loaded?
"Check the cover."
"Check the duplx unit." The duplex unit is not completely latched.
DB Assistant not found.
The slit glass is dirty.
CS-C2525E, C3225E, C3232E, C4035E
"Cannot staple. ##: maximum capacity
(staple)."
Is the maximum page quantity for stapling exceeded?
CS-C2525E, C3225E, C3232E, C4035E
"Cannot staple this paper type."
Did you select a paper type that cannot be stapled?
CS-C2525E, C3225E, C3232E, C4035E
"Cannot staple this size."
Is stapling available for the size of the loaded paper?
CS-C2525E, C3225E, C3232E, C4035E
"Change original destination. Original size
8 1/2x11"
CS-C2525E, C3225E, C3232E, C4035E
"Change the size of MP tray."
Is the specified size paper loaded in the MP tray?
CS-C2525E, C3225E, C3232E, C4035E
"Check domain name and host name."
Scanner domain name and/or host name is not set.
CS-C2525E, C3225E, C3232E, C4035E
"Check original size. Original size: 11x17, 8
1/2x11"
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Check paper size. Copy paper is not the
same size as the original."
Is the specified paper loaded? Or are the settings incorrect?
CS-C2525E, C3225E, C3232E, C4035E
Are any covers open? Coes the message indicate which cover is open?
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Check the DB Assistant PC. Contact
administrator."
CS-C2525E, C3225E, C3232E, C4035E
"Check the waste punch box."
The waste punch box is absent or not inserted correctly.
CS-C2525E, C3225E, C3232E, C4035E
"Check the waste toner box."
The waste toner box is absent or not inserted correctly.
CS-C2525E, C3225E, C3232E, C4035E
"Clean the slit glass for original fed from DP."
"Close ### cover." Is the indicated cover open?
Is the document processor cover open?
"Communication Error." Scan to PC: Sending computer status.
"Communication Error."
"Communication Error."
Is the DB Assistant version different?
The specified number does not exist.
Destination PC computer status.
The hole punch waste container is full.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Close Document Processor"
Is the document processor open while loading the original?
CS-C2525E, C3225E, C3232E, C4035E
"Close Document Processor Cover."
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
E-mail Send: Is the SMTP server running?
CS-C2525E, C3225E, C3232E, C4035E
Database Connection: Save destination computer status.
CS-C2525E, C3225E, C3232E, C4035E
"DB Assistant Server error. Contact Administrator."
An error has occurred with DB Assistant. Communication cannot comtinue.
CS-C2525E, C3225E, C3232E, C4035E
"DB Assistant Server is in use. Try again later."
DB Assistant is currently connected to another scanner.
CS-C2525E, C3225E, C3232E, C4035E
"DB Assistant Server version is different."
CS-C2525E, C3225E, C3232E, C4035E
"Destination address is not being registered."
CS-C2525E, C3225E, C3232E, C4035E
"Destination PC is in use. Try again later."
A connection currently exists between the destination PC and the scanner.
CS-C2525E, C3225E, C3232E, C4035E
"Destination PC's application is out of
order."
Is the ScanFile Utility running on the computer being used?
CS-C2525E, C3225E, C3232E, C4035E
"Destination PC's system error."
CS-C2525E, C3225E, C3232E, C4035E
"Email size, exceeds data capacity.
Email Size Limit. The size of the email attachment exceeds its limit.
CS-C2525E, C3225E, C3232E, C4035E
"Empty the waste punch box."
A file error has ocurred during printing.
The hard disk requires formatting.
Hard Disk Error: Format error.
CS-C2525E, C3225E, C3232E, C4035E
"Error has occurred. Change to printer
screen and check."
Shown when a printer error has occurred when other modes are being displayed.
CS-C2525E, C3225E, C3232E, C4035E
"Error occurred at FTP Server. Please contact
administrator."
FTP Server returned an unexpected error. Unable to save.
CS-C2525E, C3225E, C3232E, C4035E
"Exceeds pre registered copying quantity."
Is the maximum limit for copying as specified in Job Accounting mode exceeded?
CS-C2525E, C3225E, C3232E, C4035E
"Exceeds print quantity limit."
Is the maximum limit for printing as specified in Job Accounting mode exceeded?
CS-C2525E, C3225E, C3232E, C4035E
"Error occurred at the POP3 Server. Contact
Administrator."
CS-C2525E, C3225E, C3232E, C4035E
"File not found. Press [Go]."
CS-C2525E, C3225E, C3232E, C4035E
"Finisher paper capacity exceeded. (Tray #) Remove paper, and
press [Continue] key.
During printing the maximum capacity of the designated finisher tray is exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"Finisher paper capacity exceeded. (Tray #) Remove paper, and
press [Start] key.
During copying the maximum capacity of the designated finisher tray is exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"Format error Memory card."
The inserted memory card (Compact Flash) requires formatting.
CS-C2525E, C3225E, C3232E, C4035E
"Format error Hard Disk."
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 01"
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 02"
Hard Disk Error: Hard disk connection error.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 03"
Hard Disk Error: A write error has occurred. Write protect is enabled.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 04"
Hard Disk Error: Insufficient space on the hard disk to complete this operation.
Hard Disk Error: File not found.
A hard disk error has occurred.
"Image cycle."
"Insert key counter." Is the key counter inserted correctly?
"Interface occupied." Is the selected interface currently in use?
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 05"
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 06"
Hard Disk Error: Insufficient system memory.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 20"
Hard Disk Error: Hard disk is installed in the wrong slot.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 85"
Hard Disk Error: Invalid virtual mailbox tray name.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 86"
Hard Disk Error: Invalid virtual mailbox password.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 88"
Hard Disk Error: Invalid data in the virtual mailbox. The saved job data is corrupt.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 97"
Hard Disk Error: Maximum number of registered jobs is exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"HARD DISK error. Press [Go]. Code: 98"
Hard Disk Error: Invalid data in the job. The saved job data is corrupt.
CS-C2525E, C3225E, C3232E, C4035E
"HDD error. Cannot activate Job Accounting
mode."
CS-C2525E, C3225E, C3232E, C4035E
Performing internal maintenance. Toner is being added.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Insert the same Memory card."
Memory card (Compact Flash) could not be recognized when reading data from the memory card.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"KPDL error. Press [Go]."
Unable to continue processing the current print job.
"Load Paper." Is the paper source empty when printing?
"Load Paper. ### size"
Memory Card Error: Format error.
Memory Card Error: File not found.
"Memory full."
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
The correct size paper has not been loaded.
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Insert again."
Was the memory card (Compact Flash) removed during printer configuration?
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Press [Go]. Code: 01
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Press [Go]. Code: 02
Memory Card Error: Memory card insertion error.
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Press [Go]. Code: 03
Memory Card Error: A write error has occurred. Write protect is enabled.
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Press [Go]. Code: 04
Memory Card Error: Insufficient memory card space to complete this operation.
CS-C2525E, C3225E, C3232E, C4035E
"Memory card error. Press [Go]. Code: 05
CS-C2525E, C3225E, C3232E, C4035E
The current copy job cannot be processed because there is no more copy free space, or the number of originals exceeded the maximum 999 pages.
CS-C2525E, C3225E, C3232E, C4035E
"Memory full. Delete the registerd data in the
box."
The data box for document management functions has reached the permissible capacity.
CS-C2525E, C3225E, C3232E, C4035E
"Memory overflow. Press [Go]."
The current job cannot be processed due to insufficient free memory. If RAM disk is enabled decrease the RAM disk size. Additional printer memory is recommended if this error frequently occurs. If resume time has been configured for Auto Continue, printing resumes automatically after the set time has elapsed.
Is the specific destination registered?
An option ROM read error has occurred.
Out of staples.
"Paper misfeed."
CS-C2525E, C3225E, C3232E, C4035E
"Network scanner system error."
CS-C2525E, C3225E, C3232E, C4035E
"No destination address being registered."
CS-C2525E, C3225E, C3232E, C4035E
"Open cassette #, check and remove paper from
inside machine."
CS-C2525E, C3225E, C3232E, C4035E
"Option interface error. Code: ##"
Is the installed option interface slot incorrect?
CS-C2525E, C3225E, C3232E, C4035E
"Opt. ROM error. Press [Go]."
CS-C2525E, C3225E, C3232E, C4035E
"Out of staples. Add staples."
CS-C2525E, C3225E, C3232E, C4035E
"Overflow of original pages. Scanned
documents were sent."
Limit of 999 pages that can be sent at one time has been exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"Paper capacity is over the limit, unable to
copy."
The number of copies set for Color/B&W exceeds the maximum limit set in Job Accounting.
CS-C2525E, C3225E, C3232E, C4035E
"Paper cassette is out of order. Select another
paper cassette."
The cassette selected is temporarily unavailable.
CS-C2525E, C3225E, C3232E, C4035E
A paper jam has occurred. Note the location of the paper jam: J##.
CS-C2525E, C3225E, C3232E, C4035E
"PC of personal address list is in use. Try again
later."
A connection currently exists between the destination PC and the scanner.
CS-C2525E, C3225E, C3232E, C4035E
"PC's version of the personal address list is
different."
Is the Address Book for scanner version different?
CS-C2525E, C3225E, C3232E, C4035E
"Place transparency in the multi-purpose tray."
Are any transparencies loaded in the multipurpose tray? Machine will prompt for every transparency.
RAM disk error: Format error.
RAM disk error: File not found.
"Read Fonts: Failed." Unable to read font data while printing.
"Read Macro: Failed." Unable to read macro data while printing.
Remaining toner is low.
CS-C2525E, C3225E, C3232E, C4035E
"Please wait. Now in the fuser temperature
adjustment process."
A specific media type has been selected requiring correction of the fixing temperature before printing or copying.
CS-C2525E, C3225E, C3232E, C4035E
"Please wait. Remote edit."
Job Accounting editing is currently being done from a network connected computer.
CS-C2525E, C3225E, C3232E, C4035E
"Print overrun. Press [Go]."
Overrun has occurred due to insufficient memory. If resume time has been configured for Auto Continue, printing resumes automatically after the set time has elapsed. After displaying this message Page Protect is automatically set to On.
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 01
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 02
RAM disk error: RAM disk mode is set to Off.
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 03
RAM disk error: A write error has occurred. Write protect is enabled.
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 04
RAM disk error: Insufficient RAM disk space to complete this operation.
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 05
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 06
RAM disk error: Insufficient system memory.
CS-C2525E, C3225E, C3232E, C4035E
"RAM disk error. Press [Go]. Code: 98
RAM disk error: Unable to read data during sort operation. The saved job data is corrupt.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"Ready to copy. Add toner. [C][M][Y][K]"
CS-C2525E, C3225E, C3232E, C4035E
"Registration full. You can not add any more."
The waste toner box is full.
"Reposition original."
"Set cassette #." Is the indicated cassette not fully closed?
Set paper Press [Go]."
CS-C2525E, C3225E, C3232E, C4035E
"Remove paper. Finisher tray."
The maximum capacity of the DF-730 document finisher has been exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"Remove paper from inner tray of Finisher."
Paper may be left in the stapling tray of the finisher.
CS-C2525E, C3225E, C3232E, C4035E
"Remove paper from the folding tray of the
Finisher."
Paper may be left in the folding tray of the finisher.
CS-C2525E, C3225E, C3232E, C4035E
"Replace the waste toner box."
CS-C2525E, C3225E, C3232E, C4035E
Is the orientation of the specified paper different from that of the original?
CS-C2525E, C3225E, C3232E, C4035E
"Reposition original or change cassette."
Is the machine installed beneath bright fluorescent light?
CS-C2525E, C3225E, C3232E, C4035E
"Reposition original or change cassette."
Is the orientation of the specified paper different from that of the original?
CS-C2525E, C3225E, C3232E, C4035E
"Reset all originals in processor."
CS-C2525E, C3225E, C3232E, C4035E
"Reset all originals in Document Processor."
Are there any originals left in the document processor?
CS-C2525E, C3225E, C3232E, C4035E
" Reset originals in processor."
CS-C2525E, C3225E, C3232E, C4035E
"Reset feeding unit for paper cassette."
Is the paper feed unit securely pushed into the machine?
CS-C2525E, C3225E, C3232E, C4035E
"Security key is not recognized."
CS-C2525E, C3225E, C3232E, C4035E
"Sender (user) is not registered. Contact
administrator."
Is the sender (user) registered as User #001 in the scanner's sender (user) list?
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
This paper supplies paper one sheet at a time even if multiple sheets have been loaded, when printing.
"Staple jam." A staple jam has occurred.
An error has occurred.
An error has occurred.
CS-C2525E, C3225E, C3232E, C4035E
"SMTP Authentication error. Contact Administrator."
Send Email Error in Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
"System Error. Call service."
CS-C2525E, C3225E, C3232E, C4035E
"System Error. Main Power Switch Off/On."
CS-C2525E, C3225E, C3232E, C4035E
"The Path atempted to use for saving does not
exist."
Save folder does not exist or the path to the save folder is incorrect.
CS-C2525E, C3225E, C3232E, C4035E
"The top tray is full of paper. Remove paper, and press [Start] key."
During copying the maximum capacity of the top output tray is exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"The top tray is full of paper. Remove paper, and press [Continue]
key."
During copying the maximum capacity of the top output tray is exceeded.
CS-C2525E, C3225E, C3232E, C4035E
"The file was not saved. Check the destination
PC."
Has the maximum hard disk usage set by the ScanFile Utility at the destination PC been exceeded?
CS-C2525E, C3225E, C3232E, C4035E
"These functions cannot be combined."
Have you selected functions that cannot be used together?
CS-C2525E, C3225E, C3232E, C4035E
"These functions cannot be combined."
Have you selected functions that cannot be used together?
CS-C2525E, C3225E, C3232E, C4035E
"This name is already in use. Input new name
again."
CS-C2525E, C3225E, C3232E, C4035E
"This number is already in use. Input new number again."
CS-C2525E, C3225E, C3232E, C4035E
"Toner will be empty soon. [C][M][Y][K]"
The toner container will need to be replaced soon.
FTP server login failed.
Is the network cable connected properly.
CS-C2525E, C3225E, C3232E, C4035E
"Unable to copy. (Full-Color) Job Accounting
capacity has limit."
Is full color copying permitted, as specified in the users Job Accounting mode?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to copy. (Full-Color) Exceeded the
limitation of Job Accounting."
Is the maximum limit for copying as specified in Job Accounting mode exceeded?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find destination PC. Check
the PC."
Is the ScanFile Utility running on the computer being used?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find FTP server. Contact administrator."
Is the network cable connected properly? Is the FTP server running?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find PC for personal address list.
Check the PC.
firm the login account and password for SMTP Tx Authentication.
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find PC for personal address list.
Check the PC.
Is the network properly connected to the specified PC?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find PC for personal address list.
Check the PC.
Is the network properly connected to the scanner network interface?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find POP3 Server. Contact Administrator."
Are the POP3 user account or password correct?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to find SMTP server.Contact Administrator."
Can Not Connect. Network is not connected.
CS-C2525E, C3225E, C3232E, C4035E
"Unable to Log in to the FTP Server."
CS-C2525E, C3225E, C3232E, C4035E
"Unable to Log in to the POP3 Server. Contact
Administrator."
Are the POP3 user account or password correct?
CS-C2525E, C3225E, C3232E, C4035E
"Unable to use scanner."
CS-C2525E, C3225E, C3232E, C4035E
"Use alternative? Press [Go]."
Displayed when the paper source is changed.
"Virtual mailbox full." Insufficient virtual mailbox space.
"Warning image adapt."
"Warning Low Memory." Memory is low.
"Wrong password."
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
Printing is not possible at the currently set resolution due to insufficient memory.
CS-C2525E, C3225E, C3232E, C4035E
CS-C2525E, C3225E, C3232E, C4035E
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data: 10871087
Start > Inch > Start > power Off/On. (tech only)
Turn power Off/On. If code immediately returns initialize backup data: 10871087
Start > Inch > Start > power Off/On. (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
24First try turning power Off/On. If code immediately returns format hard drive: 10871087
Start > Execute > Start > power Off/On (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
20
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On. If code immediately returns initialize backup data: 10871087
Start > Inch > Start > power Off/On. (tech only)
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163
10871087 163
10871087 163
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906 Start > Execute > Start > power Off/On.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Scan errors appear on the transmission log.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
10871087 906
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Start > Execute > Start > power Off/On.
10871087 906 Start > Execute > Start > power Off/On.
Send errors are displayed on the panel only, and not recorded.
10871087 906 Start > Execute > Start > power Off/On.
Turn power Off/On.
Send errors are displayed on the panel only, and not recorded.
Service Checks1) Repl fax card.
1) Repl main PWB.
1) Run simulation U020.
1) Reload firmware, 2) Repl engine PWB.
1) Run simulation U020.
1) Reload fax firmware, 2) Install compatible fax card.
1) Replace main EEPROM, 2) Repl main PWB.
1) Contact Kyocera Service Administrative Division.
1) Reseat connectors on the main & engine PWBs, 2) Repl main PWB, 3) Repl engine PWB.
1) Reseat connectors on the main & scanner PWBs, 2) Repl main PWB, 3) Repl scanner PWB.
1) Reseat connector YC21 @ engine PWB and YC7 @ printer PWB, 2) Clean connections, reseat, or replace DIMMs or DDRs, 3) Repl printer PWB 4) Repl engine PWB.
Repl 1) DIMM, 2) main PWB.
Repl 1) DIMM, 2) main PWB.
1) Reseat connector YC4 @ main PWB and YC1 @ network scanner PWB, 2) Repl scanner PWB, 3) Repl main PWB.
1) Reseat connector YC6 @ main PWB and YC1 @ fax control PWB and fax relay PWB, 2) Repl fax control PWB, 3) Repl main PWB.
1) Reseat connector YC17 @ scanner PWB and YC1 @ DP drive PWB, 2) Repl DP drive PWB, 3) Repl scanner PWB.
1) Reseat connector YC33 @ engine PWB and YC1 @ paper feeder main PWB, 2) Repl paper feeder main PWB, 3) Repl engine PWB.
1) Reseat connector YC33 @ engine PWB and the connectors on the finisher main PWB, 2) Repl finisher main PWB, 3) Repl engine PWB.
1) Power Off/On 2) Reseat YC11 @ main PCB and connectors @ HDD, 3) Reformat HDD, 4) Repl HDD, 5) Repl main PWB.
1) Repl main PWB.
1) Repl fax card.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Repl main PWB backup battery, 2) Repl main PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reseat YC6 @ main PWB and fax PWB connectors, 2) Repl fax card, 3) Repl main PWB
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Check for lift drive problem 2) Reseat YC25 @ engine PWB (lift motor), 3) Check for open motor coil. Repl lift motor, 4) Check YC9-12 @ feed PWB goes low when lift limit switch 1 is OFF. If no, replace lift limit switch 1, 5) Repl feed PWB, 6) Repl engine PWB.
1) Check for lift drive problem 2) Reseat YC25 @ engine PWB (lift motor), 3) Check for open motor coil. Repl lift motor, 4) Check YC9-6 @ feed PWB goes low when lift limit switch 2 is OFF. If no, replace lift limit switch 2, 5) Repl feed PWB, 6) Repl engine PWB.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-5 @ PF main PWB goes low when lift switch 1 is OFF. If no, replace lift switch 1.
1) Check for lift drive problem 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-7 @ PF main PWB goes low when lift switch 2 is OFF. If no, replace lift switch 2.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB.
1) Check for lift drive problem, 2) Reseat connectors on engine PWB and PF main PWB.
1) Check for lift drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-4 @ PF Main PWB goes low when lift switch 1 is OFF. If no, repl lift switch 1. 5) Repl lift motor.
1) Check for lift drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-7 @ PF Main PWB goes low when lift switch 2 is OFF. If no, repl lift switch 2. 5) Repl lift motor.
1) Reseat connectors on engine PWB and PF main PWB, 2) Pinout harnass, 3) Repl engine PWB, 4) Repl PF main PWB.
1) Reseat YC28 @ engine PWB, 2) Defective transfer belt speed detection PWB. Repl transfer belt unit.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC8 @ engine PWB and motor connector, 3) Run sim U030. Check YC8-27 @ engine PWB for a low output. If yes, repl drive motor, 4) If no, repl engine PWB.
1) Run sim U030 (color dev motor) to check for drive problems, 2) Reseat YC26 @ engine PWB and motor connector, 3) Run sim U030. Check YC26-13 @ engine PWB for a low output. If yes, repl developing motor, 4) If no, repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC1 @ motor relay PWB and motor connector, 3) Repl drum motor BK, 4) Repl motor relay PWB, 5) Repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC1 @ motor relay PWB and motor connector, 3) Repl drum motor C, 4) Repl motor relay PWB, 5) Repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC1 @ motor relay PWB and motor connector, 3) Repl drum motor M, 4) Repl motor relay PWB, 5) Repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC1 @ motor relay PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor relay PWB, 5) Repl engine PWB.
1) Run sim U030 (fixing motor) to check for drive problems, 2) Reseat YC27 @ engine PWB and motor connector, 3) Run sim U030. Check YC27-A10 @ engine PWB for a low output. If yes, repl fixing motor, 4) If no, repl engine PWB.
1) Run sim U030 [eject motor (normal)/(reverse)] to check for drive problems, 2) Reseat YC27 @ engine PWB and motor connector, 3) Run sim U030. Check YC27-B4 @ engine PWB for a low output. If yes, repl eject motor, 4) If no, repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC26 @ engine PWB and motor connector, 3) Run sim U030. Check YC26-5 @ engine PWB for a low output. If yes, repl MP motor, 4) If no, repl engine PWB.
1) Check for drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl drive motor, 5) Repl PF main PWB, 6) Repl engine PWB.
1) Check for drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl paper conveying motor, 5) Repl PF main PWB. 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC30 @ engine PWB and motor connector, 3) Repl waste toner motor, 4) Repl engine PWB.
1) Repl scanner PWB.
1) Reseat or repl BK charge roller unit.
1) Check for drive problems, 2) Reseat YC4 & YC9 @ scanner PWB, 3) Reseat connector on scanner HPS, 4) Repl home position switch, 5) Repl scanner motor, 6) Repl scanner PWB.
1) Reseat YC6 @ scanner PWB, 2) Reseat conn @ inverter PWB, 3) Pinout harnass, 4) Adj position of shading plate, 5) Repl home position switch, 6) Repl lamp & inverter PWB, 7) Repl scanner PWB, 8) Replace CCD PWB.
1) Reseat YC6 @ scanner PWB & inverter PWB connectors, 2) Repl lamp & inverter PWB, 3) Repl SHD PWB, 4) Repl CCD PWB.
1) Reseat YC3 @ scanner PWB & YC4 @ SHD PWB, 2) Repl SHD PWB, 4) Repl CCD PWB.
1) Run simulation U020, 2) Repl scanner PWB.
1) Reseat YC16 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC16 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC16 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC16 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat or repl C charge roller unit.
1) Reseat or repl M charge roller unit.
1) Reseat or repl Y charge roller unit.
1) Reseat YC18 @ engine PWB & drum unit BK connector, 2) Repl drum unit BK, 2) Repl engine PWB.
1) Reseat YC17 @ engine PWB & drum unit C connector, 2) Repl drum unit C, 2) Repl engine PWB.
1) Reseat YC17 @ engine PWB & drum unit M connector, 2) Repl drum unit M, 2) Repl engine PWB.
1) Reseat YC18 @ engine PWB & drum unit Y connector, 2) Repl drum unit Y, 2) Repl engine PWB.
1) Defective heater 1/2 or thermostat1 or thermistor 1/2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Repl engine PWB, 2) Repl power supply PWB.
1) Defective thermistor 1/3. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater 1/2 or thermistor 1/3. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater 1/2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater3 or thermostat2 or thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater3 or thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Check wall outlet ground to neutral voltage. 2) Repl PSU, 3) Repl engine PWB.
1) Run sim 135 to check for drive problems (avoid overfilling dev units), 2) Reseat YC30 @ engine PWB & toner motor connectors, 3) Run sim 135 to check CMYK toner motor operation. Repl desired toner motor, 4) Repl engine PWB.
1) Repl developing unit BK, 2) Repl engine PWB.
1) Repl developing unit C, 2) Repl engine PWB.
1) Repl developing unit M, 2) Repl engine PWB.
1) Repl developing unit Y, 2) Repl engine PWB.
1) Reseat YC16 @ engine PWB, 2) Repl laser scanner unit, 3) Repl engine PWB.
1) Reseat YC16 @ engine PWB, 2) Repl laser scanner unit, 3) Repl engine PWB.
1) Reseat YC28 @ engine PWB, 2) Repl engine PWB.
1) Reseat YC28 @ engine PWB, 2) Repl engine PWB.
1) Reseat YC8 @ engine PWB, 2) Repl engine PWB.
1) Reseat YC8 @ engine PWB, 2) Repl engine PWB.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of transfer belt unit is installed, 2) Reinsert transfer belt unit, 2) Repl transfer belt unit.
1) Reseat YC13 @ engine PWB, 2) Repl the engine PWB.
1) Reseat YC13 @ engine PWB, 2) Repl the engine PWB.
1) Reseat YC18 @ engine PWB, 2) Repl drum unit BK.
1) Reseat YC17 @ engine PWB, 2) Repl drum unit C.
1) Reseat YC17 @ engine PWB, 2) Repl drum unit M.
1) Reseat YC18 @ engine PWB, 2) Repl drum unit Y.
1) Reseat YC18 @ engine PWB, 2) Repl developing unit BK.
1) Reseat YC17 @ engine PWB, 2) Repl developing unit C.
1) Reseat YC17 @ engine PWB, 2) Repl developing unit M.
1) Reseat YC18 @ engine PWB, 2) Repl developing unit Y.
1) Reseat punch unit connectors, 2) Repl punch motor, 3) Repl punch PWB, 4) Repl finisher main PWB.
1) Reseat connectors, 2) Pinout harnass, 3) Repl upper limit sensor, paper push sensor, or surface view sensor, 4) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & paper conveying belt motor 1 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS1, 4) Repl paper conveying belt motor 1, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC6 @ internal tray PWB & paper conveying belt motor 2 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS2, 4) Repl paper conveying belt motor 2, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC1 @ internal tray PWB & YC6 @ finisher main PWB, 2) Pinout harnass, 3) Repl internal tray PWB, 4) Repl finisher main PWB.
1) Reseat YC6 @ finisher main PWB & connector for main tray motor, 2) Pinout harnass, 3) Replace main tray upper & lower limit detection sensors & main tray upper surface detection sensor, 4) Repl main tray motor, 5) Repl finisher main PWB.
1) Reseat connectors or Replace tray lower limit sensor, push paper sensor, surface view sensor, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & side registration motor 1 connector, 2) Pinout harnass, 3) Repl side registration motor 1, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat adjustment HP sensor connector, 2) Reseat adjustment motor connector, 3) Pinout harnass, 4) Repl adjustment home position sensor. 5) Repl adjustment motor, 6) Replace finisher main PWB.
1) Reseat YC8 @ internal tray PWB & side registration motor 2 connector, 2) Pinout harnass, 3) Repl side registration motor 2, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat YC9 @ finisher main PWB & stapler moving motor 1 connector, 2) Repl stapler shift motor 1, 3) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl stapler assy, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler shift motor 2 connector, 2) Replace stapler moving motor 2, 3) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler motor connector, 2) Replace stapler motor, 3) Repl finisher main PWB.
1) Reseat YC22 @ finisher main PWB, 2) Replace centerfold unit set switch, 3) Repl finisher main PWB.
1) Reseat YC6 @ centerfold main PWB & centerfold side registration motor 1 connector, 2) Repl centerfold side registration motor 1, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Repl finisher main PWB.
1) Reseat YC6 & YC7 @ centerfold main PWB & centerfold paper conveying motor belt 1/2 connector, 2) Repl centerfold paper conveying belt motor 1/2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC8 @ centerfold main PWB & blade motor connector, 2) Repl blade motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC9 @ centerfold main PWB & centerfold staple motor connector, 2) Repl centerfold staple motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC7 @ centerfold main PWB & centerfold side registration motor 2 connector, 2) Repl centerfold side registration motor 2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC12 @ centerfold main PWB & centerfold main motor connector, 2) Repl centerfold main motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat paper entry sensor connector, 2) Clean foreign matter from paper entry sensor, 3) Repl paper entry sensor, 4) Repl finisher main PWB.
1) Reseat YC7 @ finisher main PWB & connections to the mailbox, 2) Repl mailbox main PWB, 3) Repl finisher main PWB.
1) Reseat YC2 @ mailbox main PWB & mailbox drive motor connector, 2) Repl mailbox drive motor, 3) Repl mailbox main PWB, 4) Repl finisher main PWB.
1) Reseat all connectors @ finisher main PWB. 2) Repl finisher main PWB.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Try to perform the operation again.
1) Reseat all connectors @ punch PWB & YC4 @ finisher main PWB. 2) Repl punch PWB.
1) Reseat all connectors @ mailbox PWB & YC7 @ finisher main PWB. 2) Repl mailbox main PWB.
1) Reseat all connectors @ centerfold main PWB & YC5 @ finisher main PWB. 2) Repl centerfold main PWB.
1) Reseat YC7 @scanner PWB, 2) Repl DP drive PWB,
Check to make sure that the destination computer is operating properly. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check the versions of the Scan File Utility.
Check to make sure that the computer that is running the personal Address Book is running properly.
Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly. Check with the netowrk administrator to find out whether the SMTP server is working properly.
Check the restricted and/or permitted domain names, and adjust the settings as necessary. Check to make sure that the destination email address was entered correctly.
Check to make sure that the destination email address was entered correctly.
Check with your network administrator to find out whether the SMTP server is working properly.
Consult with your network administrator to verify that the login Account Name and Password required for SMTP Authentication are correct.
Check to make sure that the Scan File Utility is running properly in that computer, or whether it is already connected to another scanner. Check to make sure that there are no problems with any connections, such as checking that the network cables are connected properly.
Check the password that is set in the destination computer.
Increase the available space on the destination computer's hard drive, then try the operation again.
Check the Scan File Utility Settings.
Try to perform the operation again after the connection to the other scanner is completed.
Perform any or all of the following procedures in order to lower the amount of data and then try scanning and transmission operation again: 1) lower the resolution of the image data. 2) Change the image quality setting to OCR. 3) Lower the number of documents (pages) that are being scanned at one time.
Check to make sure that the Scan File Utility in the destination computer is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, running in the destination computer. If the trouble is with the destination computer, fix the problem.
Check to make sure that the personal Address Book is running properly. Check to make sure that there is no software that utilizes the network, besides Scan File Utility, also running on the computer that is running the persoal Address Book. If the trouble is with the computer that is running the personal Address Book, fix that problem.
Check the computer of each group member as necessary and, if there is trouble in any of those computers, fix that problem.
Confirm that the network cable is properly connected. Verify the host name or the IP address of the FTP server is set correctly. Also contact the network administrator to confirm that the FTP server is properly operating.
Verify POP3 server settings.
Load paper.
Login to the FTP server has failed. Check to see if the username and the password have been properly set.
The storage folder is not found or the path to the storage folder is incorrect. Check to see if the storage folder in the FTP server matches the path setting registered in this machine.
Storage has failed because of an unexpected response from the FTP server. Contact the server administrator to check to see if writing is permitted to the login user account.
Check that the POP3 server is running properly. Confirm that there is no link fault by checking whether the netowrk cable is properly connected.
Change the POP3 server user account or password.
Check each error and fix the corresponding problems.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Select another paper type, or other functions.
Change the paper size.
Check the paper size.
Load paper. If the same type of paper is loaded in another cassette in the same orientation, you can press either one of the paper select keys on the left of the touch panel to switch to the cassette for copying.
Load paper of the size indicated in the MP tray.
Load paper of the size indicated in the MP tray.
No copies or prints can be made. Replace the toner container for the indicated color.
Make note of the error code number displayed. Power Off/On to reset. For details see above.
Print the Event Log in sim U000/Event Log to determine the error condition. Then perform Partial Operation Reset sim U906. For more details reference the error code above.
Color Auto Exposure cannot be combined with single color output. Change to Color Manual Exposure.
Select another paper type, or de-select punch.
Check the paper size.
Reconfigure the size of the MP tray.
Configure domain name and host name.
Load paper of a size that can be used.
Close all covers securely.
Securely fasten the waste punch box.
Securely fasten the waste toner box.
Decrease the number of sheets to be stapled to less than the maximun staple sheet count.
Select another paper type, or de-select stapling.
Poster function is not available for originals oriented 11x8 1/2, or A4. Re-orient originals in the R direction.
Original other than 11x17, 8 1/2x11, A3, or A4R, has been loaded. Poster feature is available for these sizes only.
Load the specified paper. Adjust any settings that are incorrect.
Press at areas marked C to latch the duplex unit. If it still won't clear perform a U906 reset.
Make sure that the DB Assistant is running on the PC which has DB Assistant installed.
Clean the slit glass, to the left of the copyboard glass.
Close all covers securely.
Close the document processor.
Close the document processor cover.
Try re-transmitting.
Check the computer running DB Assistant.
Try connecting again later.
Contact your system administrator.
Check the number and try again.
Try re-transmitting later.
Try re-transmitting.
Empty the waste punch box.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
An unsupported response was received from DB Assistant. Check the computer running DB Assistant.
Launch the ScanFile Utility to enable receive status.
Decrease number pf pages, or select B&W scanning, or decrease resolutiom, or in Command Center change the Data Size to [non-restricted] in [Email Basic Setting].
Verify POP3 server settings.
Press [Go].
Format the memory card.
Format the hard disk.
Format the hard disk again.
Verify the hard disk connections.
Disable write protect.
Press [Printer] to switch to the printer screen and display the specific error message.
Ask your server administrator to verify that the logged in user account has write permissions.
No additional copying is possible. See your Key Operator/Administrator to clear the users copy count, or change the allocation.
No additional printing is possible. See your Key Operator/Administrator to clear the users print count, or change the allocation.
Remove pages from the designated finisher tray and press the [Continue] key. Printing resumes.
Remove pages from the designated finisher tray and press the [Start] key. Copying resumes.
Move or delete data stored on the hard disk to increase available space.
Install more system memory.
Install the hard disk in a compatible slot.
Specify a valid name.
Enter the correct password.
Wait until the process is completed.
Try the operation again later.
Check whether the specified file name exists in the hard disk.
Additional jobs cannot be saved. Increase the maximum number of registered jobs or maximum allowed space usage.
Make note of the error code number displayed. Power Off/On to reset. For details see above.
Insert the key counter securely and completely.
Re-insert the memory card. When inserting the memory card turn Off the main power switch first.
From the printer menu open KPDL Error Print and select [On] to print an error report. Press [Go] to print data up to the point of the error. If resume time has been configured for Auto Continue, printing resumes automatically after the set time has elapsed.
Load more paper.
Format the memory card again.
Re-insert the memory card.
Disable write protect.
Load the specified paper. Adjust any settings that are incorrect. To change the paper source select the paper source from the touch panel and press [Go]. To print on the loaded paper press [Printer] and [Go]. To cancel printing press [Printer] and [Cancel].
When inserting the memory card turn Off the main switch first.
Move or delete data stored on the memory card to increase available space.
Check whether the specified file name exists in the memory card.
Press [Cancel] to cancel the copy job. Press [Continue] to copy up to the last scanned full page.
When assigning new originals to the boxes delete unnecessary data.
Press [Printer] to switch to the printer mode. To resume press [Go]. The remaining pages will be printed up to the final processed data. To cancel the print job press [Cancel].
Turn power Off/On.
Refill staple cartridge.
Try re-transmitting later.
Contact your system administrator.
Place transparency in the MP tray.
Create a new entry, or select another destination.
Completely pull out the indicated cassette and remove any paper inside.
Switch the main power Off, and install the option in the correct slot.
Press [Printer] to switch to the printer mode. To continue press [Go]. The error is cleared.
Send the excess pages separately. Depending on 2-sided or book original settings, the maximum sheets that can be sent may be 998 pages.
Set the count so that the total of Color/B&W does not exceed the maximum limit as specified in Job Accounting. See your Key Operator/Administrator to clear the users copy count, or change the allocation.
Print the Event Log in sim U000/Event Log to determine the error condition. Then perform Partial Operation Reset sim U906. For more details reference the error code above.
Leave the power switched On and follow the instructions on the panel to remove the jammed paper.
Wait until the process is completed.
Cycle the system power.
Set RAM disk mode to On.
Disable write protect.
Install more system memory.
Try the font data read operation again.
Try the macro data read operation again.
Copying is not possible until editing is completed.
Press [Printer] to switch to the printer mode. To continue press [Go]. To cancel the print job press [Cancel].
Move or delete data stored in the RAM disk to increase available space.
Check whether the specified file name exists in the RAM disk.
Only one copy may be made at a time. Replace the toner container for the indicated color.
Delete any unnecessary entries before registering a new entry.
Remove pages from the finisher tray.
Remove any paper left in the finisher.
Replace the waste toner box.
Pull out the cassette and push in securely.
To feed each sheet press [Go].
Remove any paper left in the folding tray of the finisher.
Change the orientation of the original. If you press the Start key without doing so, the original will be copied at the current size.
Reposition copier to avoid fluorescent light misrepresenting paper size.
Change the orientation of the original. If you press the Start key without doing so, the original will be copied at the current size.
Remove originals from the document processor, stack them uniformly and reset them.
Remove all originals in the document processor.
Remove originals from the document processor, stack them uniformly and reset them.
Pull out the paper feed unit and securely push it all the way into the machine.
Make note of the error code number displayed. Power Off/On to reset. Repair or replace security key.
Create a new user number 001 entry or select another user after setting the scanner default for Selec. of senders (users) to [Off].
Remove the jammed staple.
Increase the available space and try again.
Check the settings.
Change the name and re-enter.
Change the number and re-enter.
Enter the correct user ID/password for authentication at [System Setting]-[Sender List]-selected sender (if default then [001]) in Command Center.
Make note of the error code number displayed. Power Off/On to reset. For details see above.
Make note of the error code number displayed. Power Off/On to reset. For details see above.
Verify that the FTP Server save folder and the path registered in the machine are matching.
Remove pages from the top output tray and press the [Start] key. Copying resumes.
Remove pages from the top output tray and press the [Continue] key. Copying resumes.
Check the settings. Also see: "Cannot combine these functions."
Confirm that the replacement toner container for the indicated color is on-hand.
Launch the Addressbook for the scanner.
Press [Go].
No full color copying is possible. See your Key Operator/Administrator to change the full color copying permissions.
No additional copying is possible. See your Key Operator/Administrator to clear the users copy count, or change the allocation.
Launch the ScanFile Utility to enable receive status.
Confirm that the cable is properly connected. Contact system administrator.
Confirm that the PC is properly connected to the network.
Confirm that the network cable is properly connected to the scanner network interface.
Verify that the POP3 user account and password.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Make sure that the username and password have been configured.
Verify that the POP3 user account and password.
Confirm the network cable is properly connected. If the scanner has just been started try again later (~2 minutes).
Print the data stored in the virtual mailbox.
Enter the correct password.
Add memory to the printer or change the print resolution.
Print the status page to confirm the current printer memory capacity. Delete any unnecessary font or macro data.
Model Error Code DescriptionC0030
C0070
C0100
C0110
C0150
C0160
C0170
C0180
C0320
C0620
C0630
TASKalfa CS-250ci (2JZ), 300ci (2JX), 400ci (2H7), 500ci
(2JV)
Fax Control PWB Problem. Processing with fax software is disabled due to software or hardware issues.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormal Detection of Fax Control PWB Incompatability. In the initial communication with the fax control PWB , any normal communication command is not transmitted.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main PWB Backup Memory EEPROM Device Problem. Writing or erasing has not completed even after a certain time.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main PWB Backup Memory Data Problem. Reading data fron the EEPROM is abnormal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Engine PWB Backup Memory EEPROM Device Problem. No response is issued from the device in reading/writing for 5ms or more, five times successively. Mismatch of reading data from (2) locations, eight times successively. Mismatch between writing & reading data, eight times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Engine PWB Backup Memory EEPROM Data Problem. Reading data from EEPROM is abnormal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Copy Counts Problem. A checksum error is detected in the main and sub backup memories for copy counters.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Machine Number Mismatch Error. Machine number of the main PWB & engine PWB does not match. EEPROM damage.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Power CPU communication Problem. A communication error is detected (10) times in sucession.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Image DIMM Problem. DIMM is not correctly installed. DIMM cannot be accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DMA Problem. DMA transmission of image data does not complete within a specified period of time.
C0640 Hard Disk Drive cannot be accessed.
C0650
C0800
C0820
C0830
C0840
C0860
C0870
C0880
C0890
C0920
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Image DIMM Check Problem. Improper DIMM is installed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Image processing problem. JAM05 is detected twice.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Control PWB CG ROM Checksum Error. A checksum error occurred with CG ROM data of the fax control PWB.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Control PWB Flash Program Area Checksum Error. A checksum error occurred with the program of the fax control PWB.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Faults of RTC. The time is judged to go back based on the comparison of RTC time and the current time, or five years or more have passed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Control PWB Software Switch Checksum Error. A checksom error occurred with the software switch value of the fax control PWB.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Control PWB to Main PWB High Capacity Data Transfer Problem. High capacity data transfer between fax control PWB and scanner MIP PWB was not normally performed after 10 retries.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax PWB Program Archive Problem. At initialization the compressed program in the flash ROM on the fax control PWB was now successfully decompressed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Control PWB CG FONT Archive Problem. At initialization the compressed CG Font in the flash ROM on the fax control PWB was now successfully decompressed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax File System Error. The backup data is not retained for file system abnormality of flash memory of the fax control PWB.
C0940 Fax File System Error.
C1010
C1020
C1030
C1040
C1100
C1110
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Cassette #1 Lift Motor Error. When cassette 1 is inserted, lift limit switch 1 does not turn on within 12 sec of lift motor 1 turning On. Error is recorded after (4) successive attempts.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Cassette #2 Lift Motor Error. When cassette 2 is inserted, lift limit switch 2 does not turn on within 12 sec of lift motor 2 turning On. Error is recorded after (4) successive attempts.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-720 Optional Cassette #3 Lift Motor Error. When cassette 3 is inserted, lift limit switch 1 does not turn on within 12 sec of lift motor 1 turning On. Error is detected after two successive repetitions. Lift overcurrent protective monitor signal is detected exceeding 500ms during driving the motor, except during the first 1 second of operation. Error is detected after two successive repetitions.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-720 Optional Cassette #4 Lift Motor Error. When cassette 4 is inserted, lift limit switch 2 does not turn on within 12 sec of lift motor 2 turning On. Error is detected after two successive repetitions. Lift overcurrent protective monitor signal is detected exceeding 500ms during driving the motor, except during the first 1 second of operation. Error is detected after two successive repetitions.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-760 (Left) Lift Motor 1 Error. Exceeds 1 second overcurrent.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-760 (Right) Lift Motor 2 Error. Exceeds 1 second overcurrent.
C1120
C1130
C1400
C1800
C1900
C1950
C2101
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-760 (Left) Lift Motor 1 Position Problem. PF switch 1 remains off after 30 seconds of motor operation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-760 (Right) Lift Motor 2 Position Problem. PF switch 2 remains off after 30 seconds of motor operation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Rotary Guide Motor Error. Rotary guide sensor does not turn on.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-720 & PF-760 Communication Error. A communication error withb the paper feeder is detected (10) consecutive times.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-720 & PF-760 EEPROM error. Write data & Read data are not in agreement three times consecutively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Transfer Belt Unit EEPROM Error. No reponse is issued from the device in reading/writing exceeding 5ms, (5) times successively. Mismatch of reading data from two locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Motor K Error. The rated speed achievement signal does not turn to L (low) within 2 sec of motor activation. The rated speed achievement signal is at the H (high) level for 1 sec continuously after motor speed is stabilized.
C2102
C2201
C2202
C2203
C2204
C2211
C2212
C2213
C2214
C2231
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Motor CMY Error. The motor speed is not stabile for 2 sec or more. The rate speed achievement signal stays high for 1 sec continuously afte developing motor speed is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor K Error. Drum motor K does not keep the steady state speed for 5 sec continuously once the motor is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor C Error. Drum motor C does not keep the steady state speed for 5 sec continuously once the motor is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor M Error. Drum motor M does not keep the steady state speed for 5 sec continuously once the motor is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor Y Error. Drum motor Y does not keep the steady state speed for 5 sec continuously once the motor is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor K Startup Error. Drum motor K does not stablilize speed within 5 sec of activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor C Startup Error. Drum motor C does not stablilize speed within 5 sec of activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor M Startup Error. Drum motor M does not stablilize speed within 5 sec of activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor Y Startup Error. Drum motor Y does not stablilize speed within 5 sec of activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor K Main Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
C2232
C2233
C2234
C2241
C2242
C2243
C2244
C2261
C2262
C2263
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor C Main Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor M Main Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor Y Main Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor K Sub Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor C Sub Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor M Sub Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor Y Sub Sensor Error. No signal is input to the sensor for 1.5 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor K Device Error. The device alarm signal is input.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor C Device Error. The device alarm signal is input.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor M Device Error. The device alarm signal is input.
C2264
C2271
C2272
C2273
C2274
C2300
C2351
C2352
C2400
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Motor Y Device Error. The device alarm signal is input.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Position Sensor K Error. While the drum rotates two turns no signal is input to the sensor.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Position Sensor C Error. While the drum rotates two turns no signal is input to the sensor.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Position Sensor M Error. While the drum rotates two turns no signal is input to the sensor.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Position Sensor Y Error. While the drum rotates two turns no signal is input to the sensor.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Cleaning Motor K Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Cleaning Motor CMY Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Eject Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
C2500
C2550
C2600
C2700
C2810
C2950
C3100
C3200
C3210
TASKalfa CS-250ci, 300ci, 400ci, 500ci
MP Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Paper Conveying Motor Error. The motor speed is not stabile for 2 sec or more. Detection begins 1 sec after motor drive ON signal is output.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PF-720 & PF 760 Paper Conveying Motor Error. Lock signal exceeds 450ms.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Color Release Motor Error. After driving of the color release motor starts, the error signal is not at high for (4) sec continuously. After driving of the color release motor starts, the release signal does not go low within (5) sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Waste Toner Motor Error. After driving of the waste toner motor starts, the error signal is not high for (2) sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Motor Control PWB Communication Error. A communication error from the motor control PWB is detected (10) times in succession.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Exposure Lamp Problem. Input value at the time of exposure lamp illumination does not exceed the threshold value within (5) sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
CIS Lamp Problem. Input value at the time of CIS lamp illumination does not exceed the threshold value within (5) sec.
C3300
C3310
C3500
C3900
C3910
C4000
C4010
C4100
C5101
C5102
C5103
C5104
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Optical System (AGC) Problem. After AGC correct input is not obtained at the CCD.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
CIS (AGC) Problem. After AGC correct input is not obtained at the CIS.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Communication Error Between Scanner and ASIC.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
ISC PWB Backup Memory Read/Write Problem. Read & Write data does not match.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
ISC PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Polygon Motor Synchronization Problem. The rated speed achievement signal doesn't go low withing 48 sec of polygon motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Polygon Motor Steady-State Problem. The rated achievement signal turns to high every other 24 sec after polygon motor stabilization.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BD Initialization Problem. At initialization, ASIC of the engine PWB detects a beam detect error for 1 sec after polygon motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main High Voltage K Error. Abnormality of the K charge roller is detected during Vpp adjustment.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main High Voltage C Error. Abnormality of the C charge roller is detected during Vpp adjustment.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main High Voltage M Error. Abnormality of the M charge roller is detected during Vpp adjustment.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Main High Voltage Y Error. Abnormality of the Y charge roller is detected during Vpp adjustment.
C6000
C6010
C6020
C6030
C6040
C6050
C6100
C6120
C6130
C6200
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Heater 1 Break. Thermistor1 detected less than the Ready indication temperature for 90 sec during warmup. Thermistor1 detected less than 133C/266F for 5 sec during standby. Thermistor1 does not reach 75C/167F for 30 sec during warmup.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormally High Fuser Thermistor Temperature. The fuser abnormally high signal is detected for 60 sec or more.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormally High Fuser Thermistor 1 Temperature. The fuser temperature exceeds 240C/464F for 1 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fixing Thermistor 1 Break Error. Thermistor1 does not detect temperature rise of 1C/1.8F for 10 sec. When the difference between thermistor1 and thermistor2 becomes 100C/212F or more.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fixing Heater Error. Thermistor1 detects temperature change of 20C/36F for 160ms, 100 times or more since the power is turned On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormally Low Fuser Thermistor1 Temperature. During printing the temperature at the heat roller is lower than 100C/212F for 1 sec continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Heater 2 Break. Thermistor2 detected less than 100C/212F for 120 sec during driving. Thermistor2 detected less than 150C/302F for 300 sec during driving. Thermistor2 detected less than 100C/212F for 5 sec during driving.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormal High Fuser Thermistor2 Temperature. The fuser temperature exceeds 190C/374F for 1 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Thermistor2 Break Error. Thermistor2 detected less than 30C/86F for 45 sec during driving.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Heater 1 Edge Break. During warmup thermistor1 does not detect a rise of 1C/1.8F for 10 sec. Thermistor1 does not reach 90C/194F after 30 seconds during warmup.
C6220
C6230
C6400
C6410
C7000
C7100
C7101
C7102
C7103
C7104
C7200
C7210
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Abnormally High Fuser Thermistor1 Edge Temperature. Fuser temperature exceeds 250C/482F for 1 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Thermistor1 Edge Break Error. Fuser thermistor1 detects 40C/104F or lower for 30 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fuser Unit Type Mismatch Problem. Absence of the fuser unit is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Motor Problem. After activation of the toner motor the error signal is not high for 500ms continuously.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Container Motor Error. The rate speed acheivement signal does not go low within 2 sec of toner container motor activation. The rated speed achievement signal does not go high for 1 sec after the toner container motor speed is stabilized.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Sensor K Problem. Toner sensor output values are outside the desired criterion (60 < X < 944) for 3 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Sensor C Problem. Toner sensor output values are outside the desired criterion (60 < X < 944) for 3 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Sensor M Problem. Toner sensor output values are outside the desired criterion (60 < X < 944) for 3 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Toner Sensor Y Problem. Toner sensor output values are outside the desired criterion (60 < X < 944) for 3 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Broken Internal Thermistor Wire. An abnormal value is detected in the input data to inner temperature sensor 1.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Short-Circuited Internal Thermistor. An abnormal value is detected in the input data to inner temperature sensor 1.
C7240
C7250
C7401
C7402
C7403
C7404
C7411
C7412
C7413
C7414
C7420
C7800
C7901
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Broken Internal Thermistor2 Wire. An abnormal value is detected in the input data to inner temperature sensor 2.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Short-Circuited Internal Thermistor2. An abnormal value is detected in the input data to inner temperature sensor 2.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit K Type Mismatch Problem. Absence of the developing unit BK is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit C Type Mismatch Problem. Absence of the developing unit C is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit M Type Mismatch Problem. Absence of the developing unit M is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit Y Type Mismatch Problem. Absence of the developing unit Y is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Unit K Type Mismatch Problem. Absence of the drum unit BK is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Unit C Type Mismatch Problem. Absence of the drum unit C is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Unit M Type Mismatch Problem. Absence of the drum unit M is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Unit Y Type Mismatch Problem. Absence of the drum unit Y is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Transfer Belt Unit Type Mismatch Problem. Absence of the transfer belt unit is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Broken External Thermistor Wire. An abnormal value is detected in the input data to outer temperature sensor.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum K EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
C7902
C7903
C7904
C7911
C7912
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum C EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum M EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Drum Y EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit K EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit C EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
C7913
C7914
C7950
C8020
C8030
C8040
C8050
C8060
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit M EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Developing Unit Y EEPROM Error. No response is issued from the device in reading or writing for 5 sec or more, (5) times successively. Mismatch of reading data from (2) locations occurs (8) times successively. Mismatch between writing data and reading data occurs (8) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
High Voltage Control PWB Error. A communication error from the high voltage control PWB is detected (10) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PH-5A Punch Motor Problem. The lock signal of the punch motor is detected exceeding 500ms during punch motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects ON condition.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Belt Problem. The belt sensor does not turn On/Off within a specified time of the belt solenoid turning On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 1.5 sec.
C8070
C8140
C8140
C8170
C8180
C8210
C8210
C8220
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray upper surface detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray upper surface detection sensor is not detected as Off within 20 sec of main tray decending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray decending. Main tray upper limit detection sensor or main tray upper surface detection sensor remain On for 2 sec or more during main tray ascent.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Tray Elevation Motor Problem. Tray lower limit sensor or paper suface sensor1 or sensor2 cannot be detected as On within 10 sec of tray elevation motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Stapler Shift Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Stapler Problem. Jam 88 indication.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Stapler Shift Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
C8230
C8300
C8310
C8320
C8320
C8330
C8330
C8340
C8350
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Stapler Motor Problem. Jam 82 is indicated.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Adjustment Motor 2 Problem. Adjustment sensor 2 does not turn On/Off within the specified time of adjustment motor 2 activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Adjustment Motor 1 Problem. Adjustment sensor 1 does not turn On/Off within the specified time of adjustment motor 1 activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Staple Motor Problem. Jam 89.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
C8350
C8360
C8360
C8440
C8460
C8500
C8510
C8800
C8900
C8910
C8930
C9000
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Roller Motor Problem. The roller sensor does not turn On/Off within the specified time of roller motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Slide Motor Problem. The slide sensor does not turn On/Off within the specified time of slide motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-780 EEPROM Problem. Reading from or writing to the finisher EEPROM cannot be performed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
MT-720 Communication Error. The connection is detected, but communication is not possible with the mailbox.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
MT-720 Drive Motor Problem. The motor lock signal is detected for more than 500ms during mailbox drive motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Document Finisher Communication Error. A communication error from the document finisher is detected (10) times successively.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DF-760 Backup Memory Data Problem. Read and write data does not match (3) times in succession.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PH-5A Backup Memory Data Problem. Read and write data does not match (3) times in succession.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
BF-720 Backup Memory Data Problem. Read and write data does not match (3) times in succession.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-750/DP-760 Communication Problem. A communication error is detected.
C9040
C9050
C9060
C9070
C9080
C9500 No information provided
C9510 No information provided
C9520 No information provided
C9530 No information provided
C9540 No information provided
C9550 No information provided
CF000 Operation panel PWB comunication error.
CF040 Engine PWB Communication Error.
CF125 Scanner Unit Error
CF145 Fax Unit Error.
CF186
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-750/DP-760 Lift Motor Ascention Error. The tray upper limit switch does not turn On within 2 sec of DP lift motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-750/DP-760 Lift Motor Descent Error. The tray lower limit switch does not turn On within 2 sec of DP lift motor activation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-750/DP-760 EEPROM Error. Read and write data does not match. Data in the specified ara of the backup memory does not match the specified values.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-760 Communication Error Between DP & SHD. A communication error is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
DP-760 Communication Error Between DP & CIS. A communication error is detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error)
CF18A Engine Firmware Incompatible.
CF18C Document BOX error.
CF214
CF215
CF234 Data conversion error.
CF235 Error code when receiving/printing email.
CF245
CF246
CF247
CF248
CF25E Network Manager:
CF26F System State Manager:
CF278 Energy Saving Manager:
CF337 Device Error (scan control):
CF46F
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error).
CF515
CF526 System Error:
CF615
F000
F040 Engine PWB Communication Error.
F041 Scanner PWB Communication Error.
F050 Engine ROM Checksum Error.
F090 Fax Control PWB Communication Error.
E00000 or U00000
E00100 or U00100
E00200 or U00200
E00300 or U00300
E00420 or U00420
E00421 or U00421
E00430 or U00430
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Operation Panel PWB Communication Error.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: No response or line busy after the set number of redials.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Recording paper on the destination unit has run out during reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430
E00431 or U00431
E00431 or U00431
E00432 or U00432
E00432 or U00432
E00433 or U00433
E00433 or U00433
E00434 or U00434
E00435 or U00435
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435
E00440 or U00440
E00440 or U00440
E00440 or U00440
E00441 or U00441
E00450 or U00450
E00460 or U00460
E00460 or U00460
E00462 or U00462
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500
E00600 or U00600
E00601 or U00601
E00602 or U00602
E00603 or U00603
E00604 or U00604
E00610 or U00610
E00611 or U00611
E00613 or U00613
E00614 or U00614
E00615 or U00615
E00620 or U00620
E00622 or U00622
E00655 or U00655
E00656 or U00656
E00670 or U00670
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: The document processor cover is open.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Document jam or the document length exceeds the maximum.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Image scanning section problem
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: No document feed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Recording section cover open.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Recording paper jam.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Image writing section problem.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Nearly empty of recording paper.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Empty of recording paper.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Copier fixing unit problem.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Copier drive motor problem.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: CTS was not activated after RTS due to a modem error.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Power was cut off during communication.
E00677 or U00677
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700
E00800 or U00800
E00810 or U00810
E00900 or U00900
E00910 or U00910
E01000 or U01000
E01000 or U01000
E01001 or U01001
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: There was no file to transmit in the memory transmission mode.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010
E01011 or U01011
E01012 or U01012
E01013 or U01013
E01014 or U01014
E01015 or U01015
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016
E01017 or U01017
E01018 or U01018
E01019 or U01019
E01020 or U01020
E01021 or U01021
E01022 or U01022
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023
E01024 or U01024
E01025 or U01025
E01026 or U01026
E01027 or U01027
E01028 or U01028
E01040 or U01040
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041
E01042 or U01042
E01043 or U01043
E01044 or U01044
E010x45 or U01045
E01046 or U01046
E01047 or U01047
E01048 or U01048
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049
E01050 or U01050
E01051 or U01051
E01052 or U01052
E01053 or U01053
E01054 or U01054
E01055 or U01055
E01056 or U01056
E01057 or U01057
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070
E01071 or U01071
E01072 or U01072
E01073 or U01073
E01080 or U01080
E01091 or U01091
E01092 or U01092
E01100 or U01100
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A brak in loop current was detected during transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101
E01102 or U01102
E01110 or U01110
E01111 or U01111
E01112 or U01112
E01113 or U01113
E01114 or U01114
E01115 or U01115
E01116 or U01116
E01117 or U01117
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118
E01119 or U01119
E01120 or U01120
E01121 or U01121
E01122 or U01122
E01123 or U01123
E01124 or U01124
E01125 or U01125
E01126 or U01126
E01127 or U01127
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128
E01129 or U01129
E01140 or U01140
E01141 or U01141
E01142 or U01142
E01143 or U01143
E01144 or U01144
E01145 or U01145
E01146 or U01146
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147
E01148 or U01148
E01149 or U01149
E01150 or U01150
E01151 or U01151
E01152 or U01152
E01153 or U01153
E01154 or U01154
E01155 or U01155
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160
E01161 or U01161
E01162 or U01162
E01163 or U01163
E01164 or U01164
E01170 or U01170
E01172 or U01172
E01191 or U01191
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199
E01400 or U01400
E01500 or U01500
E01600 or U01600
E01700 or U01700
E01720 or U01720
E01721 or U01721
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: An invalid one-touch key was specified during communication.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred when calling in V.8 mode.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred when called in V.8 mode.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary chanel equvalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800
E01810 or U01810
E01820 or U01820
E02000 or U02000
E02100 or U02100
E02200 or U02200
E02200 or U02200
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in he period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200
E02303 or U02303
E02304 or U02304
E02400 or U02400
E03000 or U03000
E03100 or U03100
E03200 or U03200
E03200 or U03200
E03300 or U03300
E03300 or U03300
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected beofre a correct DNL signal was received.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: No document was present in the destination unit when polling reception started.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In interoffice subaddress-based buletin board reception, data was not stored in the box specified by the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In interoffice subaddress-based buletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400
E03500 or U03500
E03500 or U03500
E03500 or U03500
E03600 or U03600
E03600 or U03600
E03700 or U03700
E03700 or U03700
E04000 or U04000
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In confidential polling reception, the confidential, the specified confidential box number was not registered in the destination.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: The destination was being accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000
E04000 or U04000
E04100 or U04100
E04100 or U04100
E04200 or U04200
E04300 or U04300
E04400 or U04400
E04401 or U04401
E04500 or U04500
E05000 or U05000
E05100 or U05100
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: The destination was being accessed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Subaddress-based transmission faild because the destination unit had no subaddress-based reception capability.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200
E05300 or U05300
E09000 or U09000
E12000 or U12000
E12000 or U12000
E12100 or U12100
E14000 or U14000
E14000 or U14000
E14100 or U14100
E14100 or U14100
E19000 or U19000
E19100 or U19100
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: In subaddress-based relay reception memory overflowed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed during confidential reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed during memory reception.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200
E19300 or U19300
E19400 or U19400
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Memory transmission failed because a decoding error occurred.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1101
Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1101
Send FTP Error: Host Name. Enter the disable host name/IP address.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1102
Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1102
Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1102
Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1103
Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1104
Send Email Error: No Recipient Address. The destination address is not specified.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1105
Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1105
Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1105
Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
1106
Send Email Error: No Sender Info. Sender address is not entered.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Network is not connected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send Email Error: Can Not Connect. The specified server is not SMTP server.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2101
Send SMB/FTP Error: Can Not Connect. Network is not connected.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2102
Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2102
Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2103
Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2201
Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2202
Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2202
Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2203
Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
2204
Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
3101
Send Email/FTP Error: Server Response. The server is error status.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
3101
Send Email Error: Server Response. Server setting is not authenticated normally.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
3201
Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
5101
Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
5102
Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
5103
Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
5104
Send Software Error: Already Opened. Error for storage status in the operation handle.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
7102
Send Software Error: Socket Create. Unable to create a communication socket.
Is the acceptable staple count exceeded?
Is the indicated cassette out of paper?
"Add staples."
"Add toner [C][M][Y][K]"
"Box Limit Exceeded."
Job is restricted by Job Accounting.
"Cannot send fax."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
720f
Send Software Error: Unknown Error. Unable to determine the cause.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Send error. Job is cancelled. Press [End].
9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Acceptable staple count exceeded."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Add paper in cassette #."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Add paper to the multi-purpose tray. ## size."
Is the paper of the specified size loaded in the multipurpose tray?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Has the document finisher run out of staples?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot connect to Authentication Server."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot duplex print on this paper."
Did you select a paper size/type that cannot be duplex printed?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot execute this job."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot offset this paper."
Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Is there a dial tone when the Hook button is pressed?
"Cannot send fax."
"Cannot send fax." Has a communication error occurred?
"Check the cover."
"Check the finisher." Is the document finisher set correctly?"
"Clean the slit glass." Dirt has been identified on the slit glass.
Is the document processor cover open?
An error has occurred on the hard disk.
"Incorrect account ID." The account ID# does not match.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Is Permitted Fax # or Permitted ID # registered correctly?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot staple at the specified position."
Have you selected a position that cannot be stapled?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Cannot staple this paper."
Did you select a paper size/type that cannot be stapled?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Are any covers open? Does the message indicate which cover is open?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Check the document processor."
Is the document processor open? Is the top cover of the document processor open?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Close Document Processor Cover."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Confidential document detected."
The machine identifies the document guard pattern.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Failed to specify job accounting."
Job accounting is not specified in the print driver.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Failed to store job retention data."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Fax box limit exceeded."
Fax box is full, and no further storage is available.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Finisher tray is full of paper."
Is the acceptable storage capacity exceeded for the document finisher tray?"
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Hard Disk error. Job is cancelled. Press [End]
##"
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"KPDL error." A PostScript error has occurred.
"Machine Failure."
"Memory is full."
"Paper Jam. ###"
The waste toner box is full.
"Staple jam."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Incorrect Login User Name or Password."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Job Accounting restriction exceeded."
The print count exceeded the acceptable count restricted by Job Accounting.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Job Separator is full of paper."
Is the maximum capacity of the job separator tray exceeded?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
An internal error has occurred.Make a note of the error code number displayed on the panel. See above.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Unable to continue the job, as the memory is used up."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Make a note of the jam location number displayed on the panel. Leave the machine On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Removable memory error."
An error has occurred on the USB stick memory or Compact Flash memory.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Remove all originals in the document processor."
Are there any originals left in the document processor?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Replace all originals and press [Continue]."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Replace the waste toner box."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Scanner memory is full."
Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Set the waste toner box."
The waste toner box is not installed correctly.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
The location of the jam will be indicated on the panel. Leave the machine On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"System error. Turn the main power switch off
and on."
Make a note of the jam location number displayed on the panel. See above.
The specified file is not found.
"Warning low memory."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"The phone receiver is off the hook."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"The removable memory is not formatted."
Is the removable memory formatted by this machine?
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"The source file is not found."
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Top tray of the machine is full of paper."
The exit tray at the top of the machine is full.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
"Unknown Toner Installed [C][M][Y][K]"
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Further scanning cannot be performed due to insufficient memory.
To enter Service Mode Sim# To ExecuteTurn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
24
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
First try turning power Off/On. If code immediately returns format hard drive: 10871087
Start > Execute > Start > power Off/On (tech only)
Start > Execute > Start > power Off/On.
Turn power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
10871087 163
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
10871087 163
10871087 163
10871087 163
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Start > Execute > Start > when indicated Power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
10871087 906
10871087 906
10871087 906
10871087 906
10871087 906
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Start > Execute > Start > power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Turn power Off/On.
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Exxxxx: V.34 modem, Uxxxxx: all other modems
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Power Off/On. Send errors are displayed on the panel only, and not recorded.
Note the displayed error number. Send errors are displayed on the panel only, and not recorded.
Service Checks1) Repl fax card.
1) Repl main PWB.
1) Repl main PWB.
1) Reload firmware, 2) Repl engine PWB.
1) Reload firmware, 2) Repl engine PWB.
1) Repl engine PWB.
1) Reload fax firmware, 2) Install compatible fax card.
1) Replace main EEPROM, 2) Repl main PWB.
1) Contact Kyocera Service Administrative Division.
1) Re-insert Fax DIMM (FLS DIMM) on the main PWB port YS2, 2) Replace main PWB.
1) Reseat the signal cable to CIS & main PWB, 2) Repl main PWB.
1) Repl main PWB.
1) Repl fax card.
1) Power Off/On 2) Reseat YC1 & YC2 @ main PCB and connectors @ HDD, 3) Reformat HDD, 4) Repl HDD, 5) Repl main PWB.
1) Re-insert Fax DIMM (FLS DIMM) on the main PWB port YS2, 2) Perform sim U671-Recover Fax DIMM, 3) Replace main PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Repl main PWB backup battery, 2) Repl main PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reseat YC6 @ main PWB and fax PWB connectors, 2) Repl fax card, 3) Repl main PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reload fax firmware, 2) Repl fax control PWB.
1) Reseat optional fax card and fax memory DIMM. Upgrade firmware.
1) Check for lift drive problem 2) Reseat YC3 @ feed PWB (lift motor), 3) Check for open motor coil. Repl lift motor, 4) Check YC4-2 @ feed PWB goes low when lift limit switch 1 is OFF. If no, replace lift limit switch 1, 5) Repl feed PWB, 6) Repl engine PWB.
1) Check for lift drive problem 2) Reseat YC3 @ feed PWB (lift motor), 3) Check for open motor coil. Repl lift motor, 4) Check YC4-8 @ feed PWB goes low when lift limit switch 2 is OFF. If no, replace lift limit switch 2, 5) Repl feed PWB, 6) Repl engine PWB.
1) Check for lift drive problem, 2) Reseat connector YC27 @ engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-7 @ PF main PWB goes low when lift switch 1 is OFF. If no, replace lift switch 1.
1) Check for lift drive problem 2) Reseat connector YC27 @ engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl lift motor, 5) Check YC1-9 @ PF main PWB goes low when lift switch 2 is OFF. If no, replace lift switch 2.
1) Check for lift drive problem, 2) Reseat connector YC27 @ engine PWB and PF main PWB.
1) Check for lift drive problem, 2) Reseat connector YC27 @ engine PWB and PF main PWB.
1) Check for lift drive problems, 2) Reseat connector YC27 @ engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-4 @ PF Main PWB goes low when lift switch 1 is OFF. If no, repl lift switch 1. 5) Repl lift motor.
1) Check for lift drive problems, 2) Reseat connector YC27 @ engine PWB and PF main PWB, 3) Pinout harnass, 4) Check YC5-7 @ PF Main PWB goes low when lift switch 2 is OFF. If no, repl lift switch 2. 5) Repl lift motor.
1) Check for gear drive problems, 2) Reseat connector YC2 @ main PWB, 3) Check motor coil. If open, repl rotary guide motor, 3) Check signal state of rotary guide sensor YC2-8 goes low when sensor is off. If not repl rotary guide sensor, 4) Repl main PWB, 5) Repl engine PWB.
1) Reseat connector YC27 @ engine PWB and PF main PWB, 2) Pinout harnass, 3) Repl PF main PWB, 4) Repl engine PWB.
1) Reseat connector YC27 @ engine PWB and PF main PWB, 2) Repl engine PWB, 3) Repl PF Main PWB, 4) Repl PF-720 or PF-760.
1) Reseat YC28 @ engine PWB, 2) Defective transfer belt speed detection PWB. Repl transfer belt unit.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC16 @ engine PWB and motor connector, 3) Check that black developing unit turns/not seized, 4) Run sim U030. Check YC16-B4 @ engine PWB for a low output. If yes, repl drive motor, 5) If no, repl engine PWB.
1) Run sim U030 (color dev motor) to check for drive problems, 2) Reseat YC16 @ engine PWB and motor connector, 3) Run sim U030. Check YC16-A4 @ engine PWB for a low output. If yes, repl developing motor, 4) If no, repl engine PWB.
1) Check for drive problems, 2) Reseat YC8 @ motor control PWB and motor connector, 3) Repl drum motor K, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC6 @ motor control PWB and motor connector, 3) Repl drum motor C, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ motor control PWB and motor connector, 3) Repl drum motor M, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ motor control PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC8 @ motor control PWB and motor connector, 3) Repl drum motor K, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC6 @ motor control PWB and motor connector, 3) Repl drum motor C, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ motor control PWB and motor connector, 3) Repl drum motor M, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ motor control PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC8 @ motor control PWB and motor connector, 3) Repl drum motor K, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC6 @ motor control PWB and motor connector, 3) Repl drum motor C, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ motor control PWB and motor connector, 3) Repl drum motor M, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ motor control PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC8 @ motor control PWB and motor connector, 3) Repl drum motor K, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC6 @ motor control PWB and motor connector, 3) Repl drum motor C, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ motor control PWB and motor connector, 3) Repl drum motor M, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ motor control PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC8 @ motor control PWB and motor connector, 3) Repl drum motor K, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC6 @ motor control PWB and motor connector, 3) Repl drum motor C, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ motor control PWB and motor connector, 3) Repl drum motor M, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ motor control PWB and motor connector, 3) Repl drum motor Y, 4) Repl motor control PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC3 @ main front PWB and drum unit K connector, 3) Repl drum unit K, 4) Repl main front PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC5 @ sub front PWB and drum unit C connector, 3) Repl drum unit C, 4) Repl sub front PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 @ sub front PWB and drum unit M connector, 3) Repl drum unit M, 4) Repl sub front PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC3 @ sub front PWB and drum unit Y connector, 3) Repl drum unit Y, 4) Repl sub front PWB, 5) Repl engine PWB.
1) Run sim U030 (fuser motor) to check for drive problems, 2) Reseat YC25 @ engine PWB and motor connector, 3) Run sim U030. Check YC25-B4 @ engine PWB for a low output. If yes, repl fuser motor, 4) If no, repl engine PWB.
1) Run sim U030 (which mode?) to check for drive problems, 2) Reseat YC16 @ engine PWB and motor connector, 3) Run sim U030. Check YC16-B13 @ engine PWB for a low output. If yes, repl cleaning motor K, 4) If no, repl engine PWB.
1) Run sim U030 (which mode?) to check for drive problems, 2) Reseat YC16 @ engine PWB and motor connector, 3) Run sim U030. Check YC16-A13 @ engine PWB for a low output. If yes, repl cleaning motor CMY, 4) If no, repl engine PWB.
1) Run sim U030 [exit motor (CW)/(CCW)] to check for drive problems, 2) Reseat YC25 @ engine PWB and motor connector, 3) Run sim U030. Check YC25-A5 @ engine PWB for a low output. If yes, repl eject motor, 4) If no, repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC24 @ engine PWB and motor connector, 3) Run sim U030. Check YC24-2 @ engine PWB for a low output. If yes, repl MP motor, 4) If no, repl engine PWB.
1) Run sim U030 (conveying motor) to check for drive problems, 2) Reseat YC24 @ engine PWB and motor connector, 3) Run sim U030. If it doesn't run repl MP motor, 4) Repl feed PWB, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat connectors on engine PWB and PF main PWB, 3) Pinout harnass, 4) Repl PF paper conveying motor, 5) Repl PF main PWB, 6) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC28 @ engine PWB and motor connector, 3) Pinout harnass, 4) Repl color release motor, 5) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC12 @ engine PWB and motor connector, 3) Repl waste toner motor, 4) Repl engine PWB.
1) Reseat YC14 & YC15 @ engine PWB and motor controller connectors, 2) Repl motor control PWB, 4) Repl engine PWB.
1) Check for drive problems, 2) Reseat YC7 & YC8 @ ISM PWB, HPS connector, & scanner motor connector 3) Repl home position switch, 4) Repl scanner motor, 5) Repl ISM PWB, 6) Repl ISC PWB.
1) Reseat YC5 @ ISM PWB, 2) Reseat conn @ inverter PWB, 3) Pinout harnass, 4) Adj position of shading plate, 5) Repl lamp & inverter PWB, 6) Repl ISM PWB, 7) Repl ISC PWB, 8) Replace CCD PWB.
1) Reseat connectors on the ISM PWB & DP drive PWB, 2) Reseat conn @ inverter PWB, 3) Repl DP inverter PWB, 4) Repl CIS, 5) Repl DP driver PWB.
1) Repl ISC PWB, 2) Repl ISM PWB.
1) Repl ISC PWB, 2) Repl ISM PWB.
1) Reseat or repl K charge roller unit.
1) Reseat or repl C charge roller unit.
1) Reseat or repl M charge roller unit.
1) Reseat or repl Y charge roller unit.
1) Reseat YC5 @ ISM PWB & inverter PWB connectors, 2) Repl lamp & inverter PWB, 3) Repl ISM PWB, 4) Repl ISC PWB, 5) Repl CCD PWB.
1) Reseat inverter PWB connectors, 2) Repl inverter PWB, 3) Repl CIS, 4) Repl DP driver PWB.
1) Reseat YC2 @ CCD PWB & YC2 @ ISC PWB, 2) Repl ISC PWB, 4) Repl CCD PWB.
1) Reseat YC13 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC13 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Reseat YC13 @ engine PWB & @ laser unit, 2) Repl laser unit, 3) Repl engine PWB.
1) Defective heater 1 or thermostat1 or thermistor 1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Repl engine PWB, 2) Repl power supply PWB.
1) Defective thermistor 1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater 1 or thermistor 1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater 1 or thermistor 1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater 1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater2 or thermostat2 or thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater2 or thermistor2. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater1 or thermistor1 or thermostat1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective thermistor1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Defective heater1 or thermistor1. Repl fuser unit, 2) Repl engine PWB, 3) Repl power supply PWB.
1) Check wall outlet ground to neutral voltage. 2) Reseat YC4 @ engine PWB & YC10 @ PSU, 3) Repl engine PWB, 3) Repl PSU.
1) Reseat fuser unit. 2) Install the correct type of fuser unit.
1) Run sim 135 to check for drive problems (avoid overfilling dev units), 2) Reseat YC26 @ engine PWB & toner motor connectors, 3) Run sim 135 to check CMYK toner motor operation. Repl desired toner motor, 4) Repl engine PWB.
1) Run sim 135 to check for drive problems (avoid overfilling dev units), 2) Reseat YC26 @ engine PWB & toner container motor connectors, 3) Run sim 030 to check if remote signal YC26-A7 goes low. If yes, repl toner container motor, 4) If no, repl engine PWB.
1) Repl developing unit K, 2) Repl main front PWB, 3) Repl engine PWB.
1) Repl developing unit C, 2) Repl sub front PWB, 3) Repl engine PWB.
1) Repl developing unit M, 2) Repl sub front PWB, 3) Repl engine PWB.
1) Repl developing unit Y, 2) Repl sub front PWB, 3) Repl engine PWB.
1) Reseat YC13 @ engine PWB and laser scanner unit, 2) Repl laser scanner unit, 3) Repl engine PWB.
1) Reseat YC13 @ engine PWB and laser scanner unit, 2) Repl laser scanner unit, 3) Repl engine PWB.
1) Reseat YC8 @ engine PWB, 2) Repl engine PWB.
1) Reseat YC8 @ engine PWB, 2) Repl engine PWB.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type/color developing unit is installed 2) Reinsert developing unit, 3) Repl developing unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of drum unit is installed, 2) Reinsert drum unit, 2) Repl drum unit.
1) Check that correct type of transfer belt unit is installed, 2) Reinsert transfer belt unit, 2) Repl transfer belt unit.
1) Reseat YC1 @ main front PWB, 2) Repl the engine PWB.
1) Reseat YC3 @ main front PWB, 2) Repl drum unit K.
1) Reseat YC5 @ sub front PWB, 2) Repl drum unit C.
1) Reseat YC7 @ sub front PWB, 2) Repl drum unit M.
1) Reseat YC3 @ sub front PWB, 2) Repl drum unit Y.
1) Reseat YC4 @ main front PWB, 2) Repl developing unit K.
1) Reseat YC6 @ sub front PWB, 2) Repl developing unit C.
1) Reseat YC8 @ sub front PWB, 2) Repl developing unit M.
1) Reseat YC4 @ sub front PWB, 2) Repl developing unit Y.
1) Reseat YC30 @ engine PWB and high voltage contol PWB connectors, 2) Repl high voltage control PWB, 3) Repl engine PWB.
1) Reseat punch unit connectors, 2) Repl punch motor, 3) Repl punch PWB, 4) Repl finisher main PWB.
1) Reseat upper limit sensor connector, 2) Repl upper limit sensor, paper surface sensor1 or sensor2, 3) Repl finisher main PWB.
1) Reseat belt sensor & solenoid connectors, 2) Repl belt sensor, 3) Repl belt solenoid, 4) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & paper conveying belt motor 1 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS1, 4) Repl paper conveying belt motor 1, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC6 @ internal tray PWB & paper conveying belt motor 2 connector, 2) Pinout harnass, 3) Repl paper conveying belt HPS2, 4) Repl paper conveying belt motor 2, 5) Repl internal tray PWB, 6) Repl finisher main PWB.
1) Reseat YC1 & YC4 @ internal tray PWB, YC6 & YC24 @ finisher main PWB, 2) Pinout harnass, 3) Repl internal tray PWB, 4) Repl finisher main PWB.
1) Reseat YC11 @ finisher main PWB & connector for main tray motor, 2) Pinout harnass, 3) Replace main tray upper & lower limit detection sensors & main tray upper surface detection sensor, 4) Repl main tray motor, 5) Repl finisher main PWB.
1) Reseat connectors or Replace tray lower limit sensor, paper surface sensor1 or sensor2, 2) Reseat tray elevation motor connector, 3) Pinout harnass, 4) Repl tray elevation motor, 5) Repl finisher main PWB.
1) Reseat YC2 @ internal tray PWB & side registration motor 1 connector, 2) Pinout harnass, 3) Repl side registration motor 1, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat YC8 @ internal tray PWB & side registration motor 2 connector, 2) Pinout harnass, 3) Repl side registration motor 2, 4) Repl internal tray PWB, 5) Repl finisher main PWB.
1) Reseat YC9 @ finisher main PWB & stapler moving motor 1 connector, 2) Repl stapler shift motor 1, 3) Repl finisher main PWB.
1) Reseat stapler connector, 2) Unjam stapler, 3) Repl stapler assy, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler moving motor 2 connector, 2) Replace stapler moving motor 2, 3) Repl staple relay PWB, 4) Repl finisher main PWB.
1) Reseat YC10 @ finisher main PWB & stapler relay PWB connectors & stapler motor connector, 2) Replace stapler motor, 3) Repl stapler relay PWB, 4) Repl finisher main PWB.
1) Reseat YC5 & YC20 @ finisher main PWB, 2) Reseat YC1 & YC2 @ centerfold main PWB, 3) Replace centerfold unit set switch, 4) Repl centerfold main PWB, 5) Repl finisher main PWB.
1) Reseat YC6 @ centerfold main PWB & centerfold side registration motor 2 connector, 2) Repl centerfold side registration motor 2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC6 & YC7 @ centerfold main PWB & centerfold paper conveying motor belt 1/2 connector, 2) Repl centerfold paper conveying belt motor 1/2, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors to adjustment sensor 2 & adjustment motor 2, 2) Repl adjustment sensor 2, 3) Repl adjustment motor 2, 4) Repl finisher main PWB.
1) Reseat YC8 @ centerfold main PWB & blade motor connector, 2) Repl blade motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat connectors to adjustment sensor 1 & adjustment motor 1, 2) Repl adjustment sensor 1, 3) Repl adjustment motor 1, 4) Repl finisher main PWB.
1) Reseat YC9 @ centerfold main PWB & centerfold staple motor connector, 2) Repl centerfold staple motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat YC7 @ centerfold main PWB & centerfold side registration motor 1 connector, 2) Upgrade firmware to v. 3.02 or newer, 3) Repl centerfold side registration motor 1, 4) Repl centerfold main PWB, 5) Repl finisher main PWB.
1) Repl finisher main PWB.
1) Reseat roller sensor & roller motor connectors, 2) Repl roller sensor, 3) Repl roller motor, 4) Repl finisher main PWB.
1) Reseat YC12 @ centerfold main PWB & centerfold main motor connector, 2) Repl centerfold main motor, 3) Repl centerfold main PWB, 4) Repl finisher main PWB.
1) Reseat slide sensor & slide motor connectors, 2) Repl slide sensor, 3) Repl slide motor, 4) Repl finisher main PWB.
1) Reseat paper entry sensor connector, 2) Clean foreign matter from paper entry sensor, 3) Repl paper entry sensor, 4) Repl finisher main PWB.
1) Reseat YC7 @ finisher main PWB & connections to the mailbox, 2) Repl mailbox main PWB, 3) Repl finisher main PWB.
1) Reseat YC5 @ mailbox main PWB & mailbox drive motor connector, 2) Repl mailbox drive motor, 3) Repl mailbox main PWB, 4) Repl finisher main PWB.
1) Reseat all connectors @ engine PWB & finisher main PWB. 2) Upgrade firmware to v. 3.02 or newer, 3) Repl finisher main PWB, 4) Repl engine PWB.
1) Reseat all connectors @ finisher main PWB. 2) Install EEPROM correctly, 3) Repl finisher main PWB.
1) Reseat all connectors @ punch PWB & YC4 @ finisher main PWB. 2) Repl punch PWB.
1) Reseat all connectors @ centerfold main PWB & YC5 @ finisher main PWB. 2) Install EEPROM correctly 3) Repl centerfold main PWB.
1) Reseat YC6 @ ISM PWB & DP connector, 2) Repl DP drive PWB, 3) Repl ISM PWB.
1) Reseat connectors @ CIS, 2) Repl CIS.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
Contact Service Administrative Division.
1) Reseat upper limit switch & lift motor connectors, 2) Repl upper limit switch, 3) Repl lift motor, 4) Repl DP drive PWB.
1) Reseat lower limit switch & lift motor connectors, 2) Repl lower limit switch, 3) Repl lift motor, 4) Repl DP drive PWB.
1) Reseat connectors @ DP drive PWB, 2) Repl DP drive PWB.
1) Reseat connectors @ SHD PWB, 2) Repl SHD PWB.
1) Repl CODE DIMM. Reinstall firmware. Update engine firmware only (wait 35 minutes during update process).
1) Repl engine PWB. Possible wrong style engine PWB (low segment/high segment).
1) Upgrade firmware to the most recent version.
1) Usually occurs when upgrade between v6 and v8. Upgrade firmware to the most recent version. Do not skip ahead. Upgrade all levels.
1) Upgrade firmware to the most recent version (v. 3.02 or newer).
1) Upgrade firmware to the most recent version.
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.00 or newer).
1) Upgrade firmware to the most recent version (v. 4.00 or newer).
1) Power is turned Off at main power without turning off the power at the panel first. 2) Upgrade firmware to the most recent version (v. 3.00 or newer).
1) Upgrade firmware to the most recent version (v. 4.00 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Repl main PWB, 2) Repl ISM PWB.
1) Repl engine PWB.
1) Repl main PWB.
Load paper.
1) Upgrade firmware to the most recent version (v. 3.00 or newer).
1) Upgrade firmware to the most recent version.
1) Upgrade firmware, 2) Repl main firmware DIMM then upgrade firmware, 3) Repl main PWB, 4) Repl main operation panel PWB.
1) Upgrade firmware using USB, only with files pertaining to current model (delete non-applicable files), 2) Repl main PWB, 3) Repl engine PWB.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Check the programming of the appropriate one-touch key.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Poor line conditions. Contact local phone provider.
Enter the correct host name or IP address.
Enter the correct username/password.
Enter correct folder path.
Register [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Enter the correct user ID/password for authentication at [Advance] in Command Center. Enter the password of [Login User Name] of the [POP3] page or the [SMTP] page correctly.
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct shared name. Check if the prohibited letters below are used to share name: @()!&#$%^~[]`
Check if the prohibited letters are used to shared name: "&'()`;<>
Enter the user name with the form of either [DomainYUser], [Domain/User], or [Domain@User].
Enter the correct username/password. Check the access limit of destination folder.
Specify the destination address.
Select valid POP3 user other than [Other].
Enter the correct host name or IP address.
Enter the correct port number.
Check if the server is operating properly.
Enter the correct host name or IP address.
Check ON [SMTP] in [Avanced]-[SMTP]-[General] screen in Command Center.
Check ON in the [Scanner]-[SMB] screen in Command Center.
Check ON in the [Scanner]-[FTP] screen in Command Center.
Enter the correct [Sender Address] in [Advanced]-[SMTP]-[General] screen in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Enter the correct [SMTP Server Name] in [Advanced]-[SMTP]-[General] in Command Center.
Check if the server is operation properly. Check the network connection (cable, network condition within LAN, etc.).
Check is the server is operating properly.
Check is the server is operating properly.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Power Off/On.
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Check the network connection (cable, network condition within LAN, etc.).
Change the [E-mail Size Limit] in [Advanced]-[SMTP]-[General]-[E-mail Setting] in Command Center.
Check the settings for client/server authentication.
Check the settings for client/server authentication.
Power Off/On.
Set the number of pages to 999 or less.
Replace the appropriate toner container.
Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Load paper. If the same type of paper is loaded in another cassette in the same orientation, you can press either one of the paper select keys on the left of the touch panel to switch to the cassette for copying.
Load paper of the size and type indicated in the MP tray.
Leave the machine On and follow the instructions to replace the staple case. Press [Continue] to print without stapling. Press [Cancel] to cancel the job.
Document Box full: Press [End]. Repeat Copy Box full: Press [Continue] to copy without using Repeat Copy. Press [Cancel] to cancel job. See your key Operator/Administrator.
Press [End]. Then check: Registration of Authentication Server, Password & computer address of Authentication Server, Connection to the network. See your key Operator/Administrator.
Select another paper type. Press [Continue] to print without using duplex.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
Select another paper size. Press [Continue] to print without using offset.
If no, check that the modular cord is connected at both ends. Then check for local phone service.
See above for details.
Close all covers securely.
Close the document processor.
Set the finisher correctly.
Close the document processor cover.
The job is cancelled. Press [End].
Register the Permitted Fax # or Permitted ID #. See chapter 6 of the Fax Sys (Q) Operaton Guide.
Select a position that can be stapled. Press [Continue] to print without stapling.
Select another available paper size/type [Continue] to print without stapling.
Clean the slit glass using the cleaning cloth supplied with the document processor.
The scanned document is printed blank and sending of the document is cancelled.
The job is cancelled because it is restricted by job accounting. Press [End]. See your key Operator/Administrator.
The job is cancelled. Press [End]. See your key Operator/Administrator.
Remove paper from the document finisher tray. If printing can be restarted, the touch panel display will prompt you to press Continue. Then press [Continue].
01: Initialization Error. Initialize the HDD. 04: Insufficient space on the HDD to complete this operation. Move or delete data stored on the HDD to increase available space.
Enter the correct account ID#. See you Key Operator/Administrator.
Enter the correct user name or password.
See above for details.
Set the waste toner box correctly.
See above for details.
Cannot print any more This job is canceled. Press [End]. See your Key Operator/Administrator.
Remove paper from the job separator tray. Printing resumes.
The job is cancelled. Press [End]. See your Key Operator/Administrator.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Follow the displayed instructions to remove the jammed paper.
This job is cancelled. Press [End]. Remove or replace the removable memory.
Remove originals from the document processor.
Remove originals from the document processor, put them back in their original order, stack them uniformly and place them again. Press [Continue] to resume printing. Pres [Cancel] to cancel the job.
Replace the waste toner box. One is included in the box with each toner.
Press [Continue] to print, send, or store the scanned pages. The job cannot be processed completely. Press [Cancel] to cancel printing, sending, or storing.
Follow the displayed instructions to remove the jammed staple.
Put down the receiver.
The job is cancelled. Press [End].
Format the removable memory. Note: any data on the memory will be lost. Or use memory formatted by this machine.
Remove paper from the top exit tray, and press [Continue] to resume the job.
If the toner container was taken from a different machine of the same model while it was displaying the "Add toner. [C][M][Y][K]" message, ignore the message and use the toner.
Press [Continue] to print the scanned pages. The print job cannot be processed completely. Press [Cancel] to cancel the job.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore 0xF330 Turn power Off/On.
Wysecore 0xF331 Turn power Off/On.
Wysecore 0xF333 Turn power Off/On.
Wysecore 0xF335 Turn power Off/On.
Wysecore 0xF336 Turn power Off/On.
Wysecore 0xFB30 Turn power Off/On.
Wysecore 0xFB31 Turn power Off/On.
Component: RIP. Category: RIP. Recovery impossible error (CreatePrint and return back value of API is indirect).
Component: RIP. Category: RIP. Fail to initialize.
Component: RIP. Category: RIP. Access failure to ME.
Component: RIP. Category: RIP. Failure to switch TASK.
Component: RIP. Category: RIP. IOBL process failure.
Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore 0xFB32 Turn power Off/On.
Wysecore 0xFB33 Turn power Off/On.
Wysecore 0xFB34 Turn power Off/On.
Wysecore 0xFB35 Turn power Off/On.
Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected - waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore 0xFB36 Turn power Off/On.
Wysecore 0xFB37 Turn power Off/On.
Wysecore 0xFB38 Turn power Off/On.
Wysecore 0xFB39 Turn power Off/On.
Wysecore 0xFB3A Turn power Off/On.
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF000 Turn power Off/On.
CF000 Operation panel PWB comunication error. Turn power Off/On.
CS-1820 CF010 ROM Checksum Error.
CF010 Turn power Off/On.
CS-1820 CF012 ROM Checksum Error.
CF020 Turn power Off/On.
CF030 Main PWB System Error. Turn power Off/On.
CF040 Engine PWB Communication Error. Turn power Off/On.
CF040 Engine PWB Communication Error. Turn power Off/On.
CF041 Scanner PWB Communication Error. Turn power Off/On.
CF050 Engine ROM Checksum Error. Turn power Off/On.
CF060 Engine RAM Error. Turn power Off/On.
CF070 Turn power Off/On.
Component: HDD. Failure to initialize with "dbinit, hostif_stat_chg" comand.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Turn power Off/On.
CS-3050, CS-4050, CS-5050
Main PWB Checksum Error/System Error. Communication error between panel and main controller.
Turn power Off/On.
CS-3050, CS-4050, CS-5050
Memory Checksum Error/Operation System Error.
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
TASKalfa CS-250ci, 300ci, 400ci, 500ci
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
CS-3050, CS-4050, CS-5050
Flash ROM Error. Defective flash ROM (which?).
Model Error Code Description To enter Service Mode Sim# To ExecuteCF080 Turn power Off/On.
CF090 Fax System M Communication Error. Turn power Off/On.
CF125 Scanner Unit Error Turn power Off/On.
Wysecore CF131 Turn power Off/On.
Wysecore CF131 Turn power Off/On.
CF145 Fax Unit Error. Turn power Off/On.
CF14F Turn power Off/On.
Wysecore CF14F Turn power Off/On.
CS-3050, CS-4050, CS-5050
Flash ROM Error (during download). Defective flash ROM (which?).
CS-3050, CS-4050, CS-5050
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Component: PCM. Category: OS. Failure to initialize with "dbinit, hostif_stat_chg" comand.
Component: PCM. Category: OS. Failure to acquire Entity data with "dbinit, hostif_stat_chg" comand.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
CS-3050, CS-4050, CS-5050
Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
Component: OS. Category: OS. Primary supply voltage dropped off temporarily and recovery operation was not stable. If the input power supply voltage is not stable of the Main SW is turned Off/On quickly (about 1 second), this problem occurs.
Model Error Code Description To enter Service Mode Sim# To ExecuteCF186
CF18A Engine Firmware Incompatible.
CF18C Document BOX error.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error)
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Component: ScanSys. Category: ScanSys. When the scanner scanning parameter from the topside is in error.
Component: IPLogical. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: ipl_search_output.cpp, ipl_feeder_spec.cpp, outputcheck.cpp.
Component: Machine Configuration. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: machine_status_engine.cpp.
Component: OutputMission. Category: PrintSystem. Increasing and decreasing "Lib", in case that even if there is no original available, tried to process increasing & decreasing.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
Component: OutputMission. Category: PrintSystem. In case to specify some other value (indirect value) other than single sided/duplex/forced duplex for increasing & decreasing "Lib".
Component: OutputMission. Category: PrintSystem. In case of the address for Job setting value structure is NULL.
Component: OutputMission. Category: PrintSystem. In case of the code for output completion notice is indirect.
Component: OutputMission. Category: PrintSystem. When writing the original information to the storage, in case to get the reply back as [Other Error].
Component: OutputMission. Category: PrintSystem. In case to get the reply as [Finisher out of order Error], [No Feeder available in search] from Paper feed/eject "Lib".
Component: OutputMission. Category: PrintSystem. In case to get the reply as failure from rotation calculation "Lib".
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF1FF Turn power Off/On.
Wysecore CF1FF Turn power Off/On.
CF214 Turn power Off/On.
CF215 Turn power Off/On.
CF234 Data conversion error. Turn power Off/On.
CF235 Error code when receiving/printing email. Turn power Off/On.
CF245 Turn power Off/On.
CF246 Turn power Off/On.
Component: PrintSystem. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: print_startup.cpp.
Component: SVI. Category: LioPanel. Logical Error (In case of given parameter is NULL).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down).
Model Error Code Description To enter Service Mode Sim# To ExecuteCF247 Turn power Off/On.
Wysecore CF247 Turn power Off/On.
Wysecore CF248 Turn power Off/On.
FS-1128MFP CF248 Turn power Off/On.
CF248 Turn power Off/On.
CF256 Turn power Off/On.
Wysecore CF257 Turn power Off/On.
CF257 Turn power Off/On.
CF25E Network Manager: Turn power Off/On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down).
Component: ScanSys. Category: ScanSys. Library Error inside of ScanSys.
Component: UNKNOWN. Category: UNKNOWN.
Component: UNKNOWN. Category: UNKNOWN. Code present on with Kyocera Barfode Font CF card installed.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down).
CS-3050, CS-4050, CS-5050
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CS-3050, CS-4050, CS-5050
Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF25F Turn power Off/On.
Wysecore CF26F Turn power Off/On.
CF26F Turn power Off/On.
CF26F System State Manager: Turn power Off/On.
CF278 Energy Saving Manager: Turn power Off/On.
Wysecore CF320 Turn power Off/On.
Wysecore CF321 Turn power Off/On.
Component: LFM. Category: FaxSys. Instance Check Error, Paramemter Error from topside.
Component: PrintSys. Category: PrintSys. It occurs when the error noticed from VideoDriver. Use by Video_Driver class: Function name, factor can be found by the detail code.
CS-3050, CS-4050, CS-5050
Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Component: LioFax. Category: FaxSys. An Observer Deletion Error occurred during salvage process. Error received from the method on EventManager or message Tx.
Component: LioFax. Category: FaxSys. Segment code for LioFax initialization is different from "03KH".
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF323 Turn power Off/On.
Wysecore CF324 Turn power Off/On.
Wysecore CF325 Turn power Off/On.
Wysecore CF326 Turn power Off/On.
Wysecore CF327 Turn power Off/On.
Wysecore CF32F Turn power Off/On.
CF337 Device Error (scan control): Turn power Off/On.
Wysecore CF3FF Turn power Off/On.
Wysecore CF423 Turn power Off/On.
Component: LioFax. Category: FaxSys. Return address of Page class when doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access error.
Component: LioFax. Category: FaxSys. Entity parameter error.
Component: LioFax. Category: FaxSys. In case that the time when Error came back from LFM.
Component: LioFax. Category: FaxSys. IOBL error.
Component: LioFax. Category: FaxSys. At the time of KUIOLIB error, CodeChange error, FaxLib error (Sender recorde, Entity related error).
Component: LioFax. Category: FaxSys. Instance Check Error. Parameter Error from topside.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Component: RIP. Category: RIP. Other/System Crucial Error.
Component: FaxJOB. Category: FaxSys. As the error came back at IF for DocumentBox, JobInfo, Config Entity.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF423 Turn power Off/On.
CF423 Turn power Off/On.
CF423 Turn power Off/On.
Wysecore CF424 Turn power Off/On.
Wysecore CF424 Turn power Off/On.
Wysecore CF427 Turn power Off/On.
Component: FaxJob. Category: FaxSys. The error came back when accessing (obtaining data, setting data) to below Entity related: job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate), document_box.
CS-3050, CS-4050, CS-5050
Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CS-3050, CS-4050, CS-5050
Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
Component: FaxJob. Category: FaxSys. As the error came back when obtaining IF for system authentication from ACT_Account_Manager.
Component: FaxJob. Category: FaxSys. The date obtained from the below Entity related is unexpected data: job_ent(JobInfo).
Component: FaxJob. Category: FaxSys. The error came back for the IF of LioFax observer addition/deletion.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF42F Turn power Off/On.
Wysecore CF42F Turn power Off/On.
Wysecore CF433 Turn power Off/On.
Wysecore CF434 Turn power Off/On.
Component: FaxJob. Category: FaxSys. As handing over of the NULL pointer in the class occurred. As memory reservation with new in heap domain is failed: Assert for preventing from segment drop off.
Component: FaxJob. Category: FaxSys. When generating the class, fail new at obtaining data domain, soft logic error (software bug).
Component: NetClient. Category: ImageProcess. Entity Error.
Component: NetClient. Category: ImageProcess. Entity Data Invalid.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF437 Turn power Off/On.
Wysecore CF43F Turn power Off/On.
Wysecore CF441 Turn power Off/On.
Wysecore CF444 Turn power Off/On.
Component: NetClient. Category: ImageProcess. Other Library Error (ImageLibrary, PageData, EventManager).
Component: NetClient. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
Component: CreateScan. Category: ImageProcess. Initialize Error.
Component: CreateScan. Category: ImageProcess. Entity Data Invalid.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF445 Turn power Off/On.
Wysecore CF451 Turn power Off/On.
Turn power Off/On.
Wysecore CF453 Turn power Off/On.
Component: CreateScan. Category: ImageProcess. Middleware Error (LioScanner error).
Component: CreatePrint. Category: ImageProcess. Initialization Error.
CS-3050, CS-4050, CS-5050
CF433 CF434 CF437 CF43F CF441 CF444
CF445 CF451
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
Component: CreatePrint. Category: ImageProcess. Entity Error.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF454 Turn power Off/On.
Wysecore CF45F Turn power Off/On.
Wysecore CF460 Turn power Off/On.
Wysecore CF463 Turn power Off/On.
Component: CreatePrint. Category: ImageProcess. Entity Data Mismatch.
Component: CreatePrint. Category: ImageProcess. Other Error.
Component: CreateBox (Memory Tx). Category: ImageProcess. Unrecoverable Error.
Component: CreateBox (Memory Tx). Category: ImageProcess. Entity Error.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF46F Turn power Off/On.
CF46F Turn power Off/On.
Wysecore CF470 Turn power Off/On.
Wysecore CF473 Turn power Off/On.
Component: CreateBox (Memory Tx). Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
TASKalfa CS-250ci, 300ci, 400ci, 500ci
PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error).
Component: CreateFax. Category: ImageProcess. Unrecoverable Error.
Component: CreateFax. Category: ImageProcess. Entity Error.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF47F Turn power Off/On.
Wysecore CF484 Turn power Off/On.
Wysecore CF487 Turn power Off/On.
Wysecore CF48F Turn power Off/On.
Component: CreateFax. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
Component: Edit. Category: ImageProcess. Data Invalid (PageData).
Component: Edit. Category: ImageProcess. Other Library Error (ImageLibrary).
Component: Edit. Category: ImageProcess. Crucial.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF490 Turn power Off/On.
Wysecore CF493 Turn power Off/On.
Wysecore CF494 Turn power Off/On.
Turn power Off/On.
Component: Output(Fax). Category: ImageProcess. Unrecoverable Error.
Component: Output(Fax). Category: ImageProcess. Entity Error.
Component: Output(Fax). Category: ImageProcess. Entity Data Invalid.
CS-3050, CS-4050, CS-5050
CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 CF473 CF47F CF484 CF487 CF48F CF490 CF493
CF494
HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
Model Error Code Description To enter Service Mode Sim# To ExecuteCF515 Turn power Off/On.
CF526 System Error: Turn power Off/On.
Wysecore CF528 Turn power Off/On.
Wysecore CF530 Turn power Off/On.
Wysecore CF530 Turn power Off/On.
Wysecore CF530 Turn power Off/On.
Wysecore CF530 Turn power Off/On.
Wysecore CF530 Turn power Off/On.
TASKalfa CS-250ci, 300ci, 400ci, 500ci
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Component: SVI. Category: LioPanel. Panel data abusion error.
Component: PJL. Category: RIP. Recovery impossible error: Thread Create failed.
Component: ReportEventService. Category: RIP. Recovery impossible error: Thread Create failed.
Component: SVCTL_FaxRx_Event_Control. Category: KI Sc. As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.
Component: SVCTL_Reservation_Event_Control. Category: KI Sc. As failed to notice the event for EM_Rsv_EC_op_Event_FaxJob_Ready.
Component: SVCTL_Job_Start_Command. As JobInfo giving to JSM_JobServiceManager is NULL.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF533 Turn power Off/On.
Wysecore CF533 Turn power Off/On.
Wysecore CF551 Turn power Off/On.
Wysecore CF551 Turn power Off/On.
Wysecore CF551 Turn power Off/On.
Wysecore CF610 Turn power Off/On.
CF610 Undefined. Turn power Off/On.
CF610 System Start Error. Turn power Off/On.
CF615 Turn power Off/On.
Wysecore CF620 Turn power Off/On.
Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
Component: ReportEventService. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
Component: MLPRN. Category: NetAppl. Task generation error.
Component: MLPRT. Category: NetAppl. Task generation error.
Component: EVR_LGS. Category: NetAppl. Task generation error.
Component: SSTUP. Category: OS. Error in the SystemStartUp (Thread generation, Entity data acquisition, DiskManager operation).
CS-2540, CS-3040, CS-2560, CS-3060
CS-3050, CS-4050, CS-5050
TASKalfa CS-250ci, 300ci, 400ci, 500ci
Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error).
Component: EventManager. Category: KM-Entity. Failed to obtain/receive event from framework.
Model Error Code Description To enter Service Mode Sim# To ExecuteCF620 Unable to Print. Turn power Off/On.
CF620 Turn power Off/On.
CF620 Turn power Off/On.
Wysecore CF630 Turn power Off/On.
Wysecore CF710 Turn power Off/On.
Wysecore CF713 Turn power Off/On.
Wysecore CF720 Turn power Off/On.
Wysecore CF723 Turn power Off/On.
Wysecore CF730 Turn power Off/On.
Wysecore CF733 Turn power Off/On.
Wysecore CF743 Turn power Off/On.
CS-2540, CS-3040, CS-2560, CS-3060
CS-3050, CS-4050, CS-5050
System Error. Error acquiring the event data. Panel detects CF000 as same error.
CS-3050, CS-4050, CS-5050
System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
Component: PowerManagement. Category: OS. Failed to mount or unmount during transition of the condition.
Component: IIS. Category: NetApl. Network file written error (inetd).
Component: IIS. Category: NetApl. Entity error (inetd).
Component: IIS. Category: NetApl. Network file written error (services).
Component: IIS. Category: NetApl. Entity error (services).
Component: IIS. Category: NetApl. Network file written error (snmpd).
Component: IIS. Category: NetApl. Entity error (snmpd).
Component: IIS. Category: NetApl. Entity error (hosts allow).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF750 Turn power Off/On.
Wysecore CF753 Turn power Off/On.
Wysecore CF760 Turn power Off/On.
Wysecore CF763 Turn power Off/On.
Wysecore CF770 Turn power Off/On.
Wysecore CF773 Turn power Off/On.
Wysecore CF780 Turn power Off/On.
Wysecore CF783 Turn power Off/On.
Wysecore CF790 Turn power Off/On.
Wysecore CF793 Turn power Off/On.
Wysecore CF7A0 Turn power Off/On.
Wysecore CF7A3 Turn power Off/On.
Wysecore CF7B0 Turn power Off/On.
Component: IIS. Category: NetApl. Network file written error (hostname).
Component: IIS. Category: NetApl. Entity error (hostname).
Component: IIS. Category: NetApl. Network file written error (papd).
Component: IIS. Category: NetApl. Entity error (papd).
Component: IIS. Category: NetApl. Network file written error (cups).
Component: IIS. Category: NetApl. Entity error (cups).
Component: IIS. Category: NetApl. Network file written error (dhcclient).
Component: IIS. Category: NetApl. Entity error (dhcclient).
Component: IIS. Category: NetApl. Network file written error (smb).
Component: IIS. Category: NetApl. Entity error (smb).
Component: IIS. Category: NetApl. Network file written error (netware).
Component: IIS. Category: NetApl. Entity error (netware).
Component: IIS. Category: NetApl. Network file written error (ipfilter).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CF7B3 Turn power Off/On.
Wysecore CF7C0 Turn power Off/On.
Wysecore CF7C3 Turn power Off/On.
Wysecore CF7D0 Turn power Off/On.
Wysecore CF7D3 Turn power Off/On.
CF7D7 Turn power Off/On.
CFAxx HDD Error. Turn power Off/On.
CFAxx HDD Error. Turn power Off/On.
Wysecore CFA10 Turn power Off/On.
Wysecore CFA20 Turn power Off/On.
Wysecore CFA23 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Component: IIS. Category: NetApl. Entity error (ipfilter).
Component: IIS. Category: NetApl. Network file written error (ethermode).
Component: IIS. Category: NetApl. Entity error (ethermode).
Component: IIS. Category: NetApl. Network file written error (other).
Component: IIS. Category: NetApl. Entity error (other).
CS-3050, CS-4050, CS-5050
Readout Error of SSL (authentication data).
CS-2540, CS-3040, CS-2560, CS-3060
CS-3050, CS-4050, CS-5050
Component: OS_TOOLS. Category: OS. Error inside of hot plug detection thread, overwritten thread (failed to issue the event, failed to operate signal handler).
Component: OS_TOOLS. Category: OS. Failed to obtain memory size.
Component: OS_TOOLS. Category: OS. Access error to the Entity at master data stored area component.
Component: OS_TOOLS. Category: OS. CF-DETECT OPEN error <0x07>.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA30 Turn power Off/On.
Wysecore CFA37 Turn power Off/On.
Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL error <0x08>.
Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE error <0x09>.
Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>.
Component: OS_TOOLS. Category: OS. AES conversion IOCTL error <0x0b>.
Component: OS_TOOLS. Category: OS. AES conversion CLOSE error <0x0c>.
Component: OS_TOOLS. Category: OS. AES conversion command return value error <0x0d>.
Component: OS_TOOLS. Category: OS. Message queue creation error <0x15>.
Component: OS_TOOLS. Category: OS. Message queue Tx error <0x16>.
Component: OS_TOOLS. Category: OS. Message queue Rx error <0x17>.
Component: OS_TOOLS. Category: OS. Message queue deletion error <0x18>.
Component: OS_TOOLS. Category: OS. Event Tx error <0x19>.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFA43 Turn power Off/On.
Wysecore CFB00 Turn power Off/On.
Wysecore CFB01 Turn power Off/On.
Wysecore CFB02 Turn power Off/On.
Wysecore CFB03 Turn power Off/On.
Wysecore CFB04 Turn power Off/On.
Wysecore CFB05 Turn power Off/On.
Wysecore CFB06 Turn power Off/On.
Wysecore CFB07 Turn power Off/On.
Wysecore CFB08 Turn power Off/On.
Component: OS_TOOLS. Category: OS. Access error to the Entity at USB activation component.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_E_GENERIC).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_INVAL).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOSERVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_TIMEDOUT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOTFOUND).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_OPEN).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_CONNECT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_READ).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_WRITE).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB09 Turn power Off/On.
Wysecore CFB0A Turn power Off/On.
Wysecore CFB0B Turn power Off/On.
Wysecore CFB0C Turn power Off/On.
Wysecore CFB0D Turn power Off/On.
Wysecore CFB0E Turn power Off/On.
Wysecore CFB0F Turn power Off/On.
Wysecore CFB10 Turn power Off/On.
Wysecore CFB11 Turn power Off/On.
Wysecore CFB12 Turn power Off/On.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_CONNECT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_HANDSHAKE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_READ).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_WRITE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQTIMEDOUT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSPTIMEDOUT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_NONE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_EXPIRE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_UNKNOWN).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_NOHEADER).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB13 Turn power Off/On.
Wysecore CFB14 Turn power Off/On.
Wysecore CFB15 Turn power Off/On.
Wysecore CFB16 Turn power Off/On.
Wysecore CFB17 Turn power Off/On.
Wysecore CFB18 Turn power Off/On.
Wysecore CFB19 Turn power Off/On.
Wysecore CFB1A Turn power Off/On.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_FORMAT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_FORMAT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_CANCELLED).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_HEADER_SIZEOVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_BODY_SIZEOVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSP_HEADER_SIZEOVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_TOOMANYCONTINUE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TLS_INTOLERANT).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB1B Turn power Off/On.
Wysecore CFB1C Turn power Off/On.
Wysecore CFB1D Turn power Off/On.
Wysecore CFB1E Turn power Off/On.
Wysecore CFB1F Turn power Off/On.
Wysecore CFB20 Turn power Off/On.
Wysecore CFB21 Turn power Off/On.
Wysecore CFB22 Turn power Off/On.
Wysecore CFB23 Turn power Off/On.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_OPEN).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_READ).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_SIZEOVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_NO_CONTENT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYREDIRECT).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYAUTH).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB24 Turn power Off/On.
Wysecore CFB25 Turn power Off/On.
Wysecore CFB26 Turn power Off/On.
Wysecore CFB27 Turn power Off/On.
Wysecore CFB28 Turn power Off/On.
Wysecore CFB29 Turn power Off/On.
Wysecore CFB2A Turn power Off/On.
Wysecore CFB2B Turn power Off/On.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADURL).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADMIMETYPE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_MIXEDSECURETYPE).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUT_REQUIRED).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB2C Turn power Off/On.
CFB2C CFB30 CFB31 Turn power Off/On.
Wysecore CFB30 Turn power Off/On.
CFB30 Turn power Off/On.
CFB30 Turn power Off/On.
Wysecore CFB31 Turn power Off/On.
CFB31 Corrupt Firmware on Main EEPROM. Turn power Off/On.
CFB31 Corrupt Firmware on Main EEPROM. Turn power Off/On.
Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SEGFAULT).
CS-3050, CS-4050, CS-5050
Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CS-2540, CS-3040, CS-2560, CS-3060
Incompatible Level Of Firmware on Main EEPROM.
CS-3050, CS-4050, CS-5050
Incompatible Level Of Firmware on Main EEPROM.
Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CS-2540, CS-3040, CS-2560, CS-3060
CS-3050, CS-4050, CS-5050
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB32 Turn power Off/On.
CFB32 Turn power Off/On.
Wysecore CFB33 Turn power Off/On.
CFB33 Turn power Off/On.
Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
CS-3050, CS-4050, CS-5050
Panel Error. Timeout request for start up command. Start command hasn't been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected - waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
CS-3050, CS-4050, CS-5050
Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB34 Turn power Off/On.
Wysecore CFB35 Turn power Off/On.
Wysecore CFB36 Turn power Off/On.
Wysecore CFB37 Turn power Off/On.
Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
Model Error Code Description To enter Service Mode Sim# To ExecuteWysecore CFB38 Turn power Off/On.
Wysecore CFB39 Turn power Off/On.
Wysecore CFB3A Turn power Off/On.
Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).
Service ChecksEditor's Note: There are some interesting spelling errors here that I have not corrected.
There is a possibility of the problem with the Panel PWB or Controller.
There is a possibility of the problem with the Panel PWB or Controller.
Service ChecksThere is a possibility that the controller is not starting up. The reason of this is that suspecting the Main software written failure, CODE DIMM commection failure, System file damage on HDD. There is a possibility that connection failure between panel and communication line of the controller PWB is occurred. There is a possibility of the problem for Panel PWB.Controller PWB got out of control. This occurs if the comunication with controller is cut off, there is a possibility of the problem with controller PWB, Panel PWB, Harness. There is a possibility that System file on HDD is
Service Checks1) Exchange HDD.
1) Repl main PWB.
1) Repl engine PWB.
1) Repl engine PWB.
1) Repl flash ROM.
1) Repl CODE DIMM. Reinstall firmware. Update engine firmware only (wait 35 minutes during update process).
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Check harnass connections @ engine PWB, 2) Repl engine PWB, 3) Repl main PWB.
1) Power Off/On, 2) Replace main PWB. Contact Service Administrative Division.
1) Repl expansion memory, 2) Repl main PWB.
1) Repl main PWB, 2) Repl engine PWB.
1) Repl engine PWB. Possible wrong style engine PWB (low segment/high segment).
1) Repl main PWB, 2) Repl scanner PWB.
Service Checks1) Repl flash ROM.
1) Repl main PWB.
1) Exchange HDD.
1) Turn power Off/On to reset, 2) Repl PSU PWB.
1) Turn power Off/On to reset, 2) Repl PSU PWB.
Service Checks1) Upgrade firmware to the most recent version.
1) Usually occurs when upgrade between v6 and v8. Upgrade firmware to the most recent version. Do not skip ahead. Upgrade all levels.1) Upgrade firmware to the most recent version (v. 3.02 or newer).
Service Checks
1) Upgrade firmware to the most recent version.
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
Service Checks
1) Replace Barcode Font CF.
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Set emulation from PCL XL to KPDL.
1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Reinstall fax sys M, 2) Repl fax sys M.
1) Reinstall fax sys, 2) Repl fax sys.
1) Reinstall fax sys M, 2) Repl fax sys M.
1) Upgrade firmware to the most recent version (v. 3.00 or newer).
Service Checks
1) Upgrade firmware above v.2.04A. (at this printing v.2.20C).
1) Upgrade firmware to the most recent version (v. 4.00 or newer).
1) Power is turned Off at main power without turning off the power at the panel first. 2) Upgrade firmware to the most recent version (v. 3.00 or newer).
Service Checks
1) Upgrade firmware to the most recent version (v. 4.00 or newer).
Service Checks
1) Reinstall fax sys M, 2) Reload firmware, 3)Repl fax sys M.
1) Reinstall fax sys M, 2) Reload firmware, 3)Repl fax sys M.
Service Checks
1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Upgrade firmware to the most recent version (v. 3.06 or newer).
1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl 1) Power Off/On, if re-occurs 2) HDD Initial in system menu (System Menu, Adjustment/Maintenance, System Initialization). Power Off/On, if re-occurs 3) Reformat HDD (Status, 10871087, 024, Start, Execute, Start). Power Off/On, if re-occurs 4) Repl
Service Checks
1) Upgrade firmware to the most recent version (v. 3.00 or newer).
Service Checks
1) Power Off/On.
1) Run simulation U989 HDD Scandisk.
1) Upgrade firmware to the most recent version.
Service Checks1) Bug in firmware v. 3.001 & 03/08A. Upgrade to most current firmware (currently 2.42A 02-02-10), 2) Check print driver/emulation. May occur using PCL5e. Select PCL XL.1) Power Off/On, 2) Reseat DIMM for operation panel, then reload firmware, 3) Repl DIMM for operation panel, then reload firmware.1) Use KM-Net Viewer to update barcode files.
Service Checks
1) Run U020, 2) Run U022, 3) Run U024.
Service Checks
1) Flash machine.
1) Power Off/On, 2) Reload firmware, 3) Repl Panel or main DIMM, 4) Reseat connectors to operation panel and main controller, 5) Repl operation panel PWB, 6) Repl main PWB. 7) May occur after HDD replacement. Power Off/On to There is a possibility of the problem with the Panel PWB or Controller.
1) Flash machine, 2) Replace expanded memory.
There is a possibility of the problem with the Panel PWB or Controller.
1) Repl main EEPROM then flash.
1) Repl main EEPROM then flash.
Service ChecksThere is a possibility that the controller is not starting up. The reason of this is that suspecting the Main software written failure, CODE DIMM commection failure, System file damage on HDD. There is a possibility that connection failure between panel and communication line of the controller PWB is occurred. There is a possibility of the problem for Panel PWB.1) Power Off/On, 2) Reseat & clean contacts of main DIMM & expansion memory, 3) Reload firmware, 4) Repl main DIMM or expansion memory, 5) Reseat connectors to operation panel and main controller, 6) Repl operation panel PWB, 7) Reformat or repl HDD.Controller PWB got out of control. This occurs if the comunication with controller is cut off, there is a possibility of the problem with controller PWB, Panel PWB, Harness. There is a possibility that System file on HDD is 1) Power Off/On, 2) Reseat & clean contacts of main DIMM, 3) Reload firmware, 4) Repl main DIMM, 5) Reseat connectors to operation panel and main controller, 6) Repl operation panel PWB, 7) Repl main PWB, 8) Reformat or repl