[ 1 ]___[ 11:52:39465 ]
TRANSCRIPT
_____[ 1 ]___[ 11:52:39,465 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity cd 11001101 Cell identity value1: Hex-Wert verwenden3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present 1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 2 ]___[ 11:52:39,684 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1c 00011100 MESSAGE TYPE : SYSTEM INFORMATION TYPE 4
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAI), ID of MSC (hex)04 00000100 Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters 65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select ---00101 Max Tx power level : MS may use 5
08 0------- No Additional cells in SysInfo 7-8 -0------ New establishm.cause: not supported --001000 RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parametersa5 10------ Max. of retransmissions --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestab.in cell: not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access forbidden ------00 Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access forbidden00 00000000 Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access forbidden
: SI4 Rest Octets : SI4 Rest Octets_O : Optional selection parameters 0 Selection Parameters = not present: End Optional selection parameters
: Optional Power offset 0 Power Offset = not present: End Optional Power offset: GPRS Indicator 0 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;: End GPRS Indicator: End SI4 Rest Octets_O : Break Indicator 1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM INFORMATION TYPE 7 and 8: End SI4 Restoctet
_____[ 3 ]___[ 11:52:40,395 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity cd 11001101 Cell identity value1: Hex-Wert verwenden3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present 1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 4 ]___[ 11:52:40,434 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 01 00 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
21 00100001 MESSAGE TYPE : PAGING REQUEST TYPE 1
00 ----00-- spare bits : 0 ------00 Page Mode : Normal paging --00---- Channel Needed : (first) Any Channel 00------ Channel Needed : (second) Any Channel
: Mobile Identity 101 00000001 length of Mob.ident.: 1 00 0000---- Identity Digit 1 : hex value = f, if TMSI/P-TMSI ----0--- No. of ID digits : even -----000 Type of identity : No Identity
_____[ 5 ]___[ 11:52:40,863 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 20 00 00 00 00 00 00 00 10 20 00 20 00 a5 00 00 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
19 00011001 MESSAGE TYPE : SYSTEM INFORMATION TYPE 1
: Cell Channel Description 00 00------ Format Type : Bit Map 0 format --00---- 2 spare bits : 0
20 --1----- Cell Allocation : ARFCN 10210 ---1---- Cell Allocation : ARFCN 3720 --1----- Cell Allocation : ARFCN 3020 --1----- Cell Allocation : ARFCN 14
: RACH Control Parameters a5 10------ Max. of retransmiss : 4 --1001-- slots to spread TX : 12 ------0- The cell is barred : no -------1 Call reestabl.i.cell : not allowed
00 00000--- Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl. -----0-- Emergency Call EC 10 : allowed ------00 Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00 00000000 Acc. contr. cl. 0-7 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position 0 no NCH Position 0101011 spare padding
_____[ 6 ]___[ 11:52:41,207 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 04 10 00 00 00 00 00 c0 a2 9d 00 00 08 a5 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1a 00011010 MESSAGHE TYPE : SYSTEM INFORMATION TYPE 2
00 --0----- Extension Indicator : The IE carries the complete BA ---0---- BCCH alloc. sequ.num: 0
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 39a2 1------- BCCH alloc. RF chan.: 32 --1----- BCCH alloc. RF chan.: 30 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
a5 10------ Max. of retransmiss.: 4 --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- acc ctrl class 11-15: 0/1 access permitted/forbidden ------00 acc ctrl class 8-9 : 0/1 access permitted/forbidden
00 00000000 acc ctrl class 0-7 : 0/1 access permitted/forbidden
_____[ 7 ]___[ 11:52:41,805 ]___[ DOWN ]____[ BCCH ]______________________________
06 00 b0 a0 01 f8 05 85 86 7c a1 08 05 18 03 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
00 00000000 MESSAGE TYPE : SYSTEM INFORMATION TYPE 13
1------- SI 13 Restoctet : present -011---- BCCH_CHANGE_MARK : 3 ----0000 SI_CHANGE_FIELD : Update of unspecified SI messages
1 SI13_CHANGE_MARK = present 01 SI13_CHANGE_MARK : 1
: GPRS Mobile Allocation IE
000000 HSN (hopping sequence number) = 0 0 RFL number list struckt = not present 0 MA_Length and Bitmap = present 000011 BITMAP_LENGTH : 3+1 BITMAP : 1111: End GPRS Mobile Allocation
0 PBCCH not present in Cell 00000001 RAC (Routing Area Code) = 1 0 SPGC_CCCH_SUP : SPLIT_PG_CYCLE not supported on CCCH: Priority access 110 packet access is allowed for priority level 1 to 4;: Network Control Order 00 NETWORK_CONTR. ORDER: MS controlled cell re-selection, no measurement reporting.
: GPRS CELL OPTIONS IE
01 NMO Network Mode of Operation II : No PPCH available, no Gs If
011 T3168 : (3+1)x500 ms 000----- T3192 : 500msec ---011-- DRXTIMER_MAX ------0- ACCESS_BURST_TYPE : Use 8 bit access burst -------0 default format is four access bursts 1111 BS_CV_MAX : Countdown Value = 15 1 PAN description = present 001 PAN_DEC 010 PAN_INC 000 PAN_MAX : Max value for counter N3102= 5
: End GPRS Cell Options: GPRS Power Control Param structure
1000 ALPHA = 8 x 0,1 01000 T_AVG_W = 8 00000 T_AVG_T = 0 1 PC_MEAS_CHAN : Downlink Measurement shall be made on PDCH 0100 N_AVG_I : 2 exp (4/2): End GPRS Power Control Param structure
0110000 spare padding : 0
_____[ 8 ]___[ 11:52:42,438 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity aa 10101010 Cell identity value1: Hex-Wert verwendenb2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present
1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 9 ]___[ 11:52:45,270 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity aa 10101010 Cell identity value1: Hex-Wert verwendenb2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots
------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present 1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 10 ]___[ 11:52:46,094 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 05 f4 64 11 77 9e 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
21 00100001 MESSAGE TYPE : PAGING REQUEST TYPE 1
00 ----00-- spare bits : 0 ------00 Page Mode : Normal paging --00---- Channel Needed : (first) Any Channel 00------ Channel Needed : (second) Any Channel
: Mobile Identity 105 00000101 length of Mob.ident.: 5 f4 1111---- Identity Digit 1 : hex value = f, if TMSI/P-TMSI ----0--- No. of ID digits : even -----100 Type of identity : TMSI/P-TMSI64 01100100 Identity Digit 2,3 : take hex value11 00010001 Identity Digit 4,5 : take hex value 77 01110111 Identity Digit 6,7 : take hex value 9e 10011110 Identity Digit 8,9 : take hex value
_____[ 11 ]___[ 11:52:46,172 ]___[ DOWN ]____[ CCCH ]______________________________
06 21 00 05 f4 64 10 ae e8 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
21 00100001 MESSAGE TYPE : PAGING REQUEST TYPE 1
00 ----00-- spare bits : 0 ------00 Page Mode : Normal paging --00---- Channel Needed : (first) Any Channel 00------ Channel Needed : (second) Any Channel
: Mobile Identity 105 00000101 length of Mob.ident.: 5
f4 1111---- Identity Digit 1 : hex value = f, if TMSI/P-TMSI ----0--- No. of ID digits : even -----100 Type of identity : TMSI/P-TMSI64 01100100 Identity Digit 2,3 : take hex value10 00010000 Identity Digit 4,5 : take hex value ae 10101110 Identity Digit 6,7 : take hex value e8 11101000 Identity Digit 8,9 : take hex value
_____[ 12 ]___[ 11:52:46,273 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1c 00011100 MESSAGE TYPE : SYSTEM INFORMATION TYPE 4
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAI), ID of MSC (hex)04 00000100 Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters 65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select ---00101 Max Tx power level : MS may use 5
08 0------- No Additional cells in SysInfo 7-8 -0------ New establishm.cause: not supported --001000 RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parametersa5 10------ Max. of retransmissions --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestab.in cell: not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access forbidden ------00 Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access forbidden00 00000000 Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access forbidden
: SI4 Rest Octets : SI4 Rest Octets_O : Optional selection parameters 0 Selection Parameters = not present: End Optional selection parameters: Optional Power offset 0 Power Offset = not present: End Optional Power offset: GPRS Indicator 0 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position
0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;: End GPRS Indicator: End SI4 Rest Octets_O : Break Indicator 1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM INFORMATION TYPE 7 and 8: End SI4 Restoctet
_____[ 13 ]___[ 11:52:46,484 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 20 00 00 00 00 00 00 00 10 20 00 20 00 a5 00 00 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
19 00011001 MESSAGE TYPE : SYSTEM INFORMATION TYPE 1
: Cell Channel Description 00 00------ Format Type : Bit Map 0 format --00---- 2 spare bits : 0
20 --1----- Cell Allocation : ARFCN 10210 ---1---- Cell Allocation : ARFCN 3720 --1----- Cell Allocation : ARFCN 3020 --1----- Cell Allocation : ARFCN 14
: RACH Control Parameters a5 10------ Max. of retransmiss : 4 --1001-- slots to spread TX : 12 ------0- The cell is barred : no -------1 Call reestabl.i.cell : not allowed
00 00000--- Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl. -----0-- Emergency Call EC 10 : allowed ------00 Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00 00000000 Acc. contr. cl. 0-7 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position 0 no NCH Position 0101011 spare padding
_____[ 14 ]___[ 11:52:46,723 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 04 10 00 00 00 00 00 c0 a2 9d 00 00 08 a5 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1a 00011010 MESSAGHE TYPE : SYSTEM INFORMATION TYPE 2
00 --0----- Extension Indicator : The IE carries the complete BA ---0---- BCCH alloc. sequ.num: 0
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 39a2 1------- BCCH alloc. RF chan.: 32 --1----- BCCH alloc. RF chan.: 30 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21
----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
a5 10------ Max. of retransmiss.: 4 --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- acc ctrl class 11-15: 0/1 access permitted/forbidden ------00 acc ctrl class 8-9 : 0/1 access permitted/forbidden
00 00000000 acc ctrl class 0-7 : 0/1 access permitted/forbidden
_____[ 15 ]___[ 11:52:46,734 ]___[ DOWN ]____[ CCCH ]______________________________
06 39 03 71 90 00 84 3b ab 02 61 80 1e 9c 3d 37 01 01 0d 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
_____[ 16 ]___[ 11:52:46,742 ]___[ UP ]___________________________________________
06 27 01 03 33 19 81 05 f4 64 11 77 9e
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
27 0------- 1 spare bit : 0 -0------ Send sequence number: value --100111 MESSAGE TYPE : PAGING RESPONSE
: Ciphering Key Sequence Number01 ----0--- 1 spare bit : 0 -----001 Ciph. key sequ. num.: 1 (7=no key available) 0000---- 4 spare bits : 0
: Mobile Station Classmark 2 03 00000011 lgth of MS Cl.Mark2 : 3
33 0------- 1 spare : 0 -01----- Revision Level : Used by phase 2 mobile stations ---1---- "Controlled Early Classmark Sending" option is implemented in the MS ----0--- Encryp.Algor. A5_1 : available -----011 RF power capability : Class 4, handheld
19 0------- 1 spare bit : 0 -0------ pseudo-synch.capab. : not present --01---- SS Screening Indic. : phase 2 error handling ----1--- Mobile station supports mobile terminated point to point SMS -----0-- no VoiceBroadcastService (VBS) capability or no notifications wanted ------0- no VoiceGroupCallService (VGCS) capability or no notifications wanted -------1 The MS does support the E-GSM or R-GSM
81 -0------ 1 spare bit : 0 --0----- LocationServiceValueAdded Capability not supported ---0---- 1 spare bit : 0 ----0--- SoLSA Capability : not supported -----0-- Network initiated MO CM connection request not supported. ------0- encryp.algorith.A5/3: not available
-------1 encryp.algorith.A5/2: available
: Mobile Identity
05 00000101 length of Mob. ident: 5 f4 1111---- Identity Digit 1 : 15 ----0--- No. of ID digits : even -----100 Type of identity : TMSI/P-TMSI64 01100100 Identity Digit 2,3 : take hex value11 00010001 Identity Digit 4,5 : take hex value 77 01110111 Identity Digit 6,7 : take hex value 9e 10011110 Identity Digit 8,9 : take hex value
_____[ 17 ]___[ 11:52:46,926 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 18 ]___[ 11:52:47,055 ]___[ UP ]____[ SDCCH ]______________________________
06 16 03 33 19 81 20 02 60 14
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
16 00010110 MESSAGE TYPE : CLASSMARK CHANGE
: Mobile Station Classmark 2 03 00000011 length : 3
33 0------- 1 spare : 0 -01----- Revision Level : Used by phase 2 mobile stations ---1---- "Controlled Early Classmark Sending" option is implemented in the MS
----0--- Encryp.Algor. A5_1 : available -----011 RF power capability : Class 4, handheld
19 0------- 1 spare bit : 0 -0------ pseudo-synch.capab. : not present --01---- SS Screening Indic. : phase 2 error handling ----1--- Mobile station supports mobile terminated point to point SMS -----0-- no VoiceBroadcastService (VBS) capability or no notifications wanted ------0- no VoiceGroupCallService (VGCS) capability or no notifications wanted -------1 The MS does support the E-GSM or R-GSM
81 1------- The MS does support any options that are indicated in CM3 -0------ 1 spare bit : 0 --0----- LocationServiceValueAdded Capability not supported ---0---- 1 spare bit : 0 ----0--- SoLSA Capability : not supported -----0-- Network initiated MO CM connection request not supported. ------0- encryp.algorith.A5/3: not available -------1 encryp.algorith.A5/2: available
20 00100000 INFORMATION ELEMENT : CLASSMARK 3
02 00000010 length : 2
60 0110---- P-GSM, E-GSM or R-GSM supported, DCS 1800 not supported ----0--- encryption algorithm A5/7 not available -----0-- encryption algorithm A5/6 not available ------0- encryption algorithm A5/5 not available -------0 encryption algorithm A5/4 not available
14 0001---- Associated Radio capability 1 = 1 ----0100 Associated Radio capability 2 = 4
_____[ 19 ]___[ 11:52:47,324 ]___[ DOWN ]____[ SDCCH ]______________________________
06 13
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages13 00010011 MESSAGE TYPE : CLASSMARK ENQUIRY
_____[ 20 ]___[ 11:52:47,324 ]___[ UP ]___________________________________________
06 16 03 33 19 81 20 02 60 14
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
16 00010110 MESSAGE TYPE : CLASSMARK CHANGE
: Mobile Station Classmark 2 03 00000011 length : 3
33 0------- 1 spare : 0 -01----- Revision Level : Used by phase 2 mobile stations ---1---- "Controlled Early Classmark Sending" option is implemented in the MS ----0--- Encryp.Algor. A5_1 : available -----011 RF power capability : Class 4, handheld
19 0------- 1 spare bit : 0 -0------ pseudo-synch.capab. : not present --01---- SS Screening Indic. : phase 2 error handling
----1--- Mobile station supports mobile terminated point to point SMS -----0-- no VoiceBroadcastService (VBS) capability or no notifications wanted ------0- no VoiceGroupCallService (VGCS) capability or no notifications wanted -------1 The MS does support the E-GSM or R-GSM
81 1------- The MS does support any options that are indicated in CM3 -0------ 1 spare bit : 0 --0----- LocationServiceValueAdded Capability not supported ---0---- 1 spare bit : 0 ----0--- SoLSA Capability : not supported -----0-- Network initiated MO CM connection request not supported. ------0- encryp.algorith.A5/3: not available -------1 encryp.algorith.A5/2: available
20 00100000 INFORMATION ELEMENT : CLASSMARK 3
02 00000010 length : 2
60 0110---- P-GSM, E-GSM or R-GSM supported, DCS 1800 not supported ----0--- encryption algorithm A5/7 not available -----0-- encryption algorithm A5/6 not available ------0- encryption algorithm A5/5 not available -------0 encryption algorithm A5/4 not available
14 0001---- Associated Radio capability 1 = 1 ----0100 Associated Radio capability 2 = 4
_____[ 21 ]___[ 11:52:47,395 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 22 ]___[ 11:52:47,445 ]___[ UP ]___________________________________________
06 15 94 14 01 54 0b a9 a5 a3 00 e9 47 7c 91 bc 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
94 1------- BA used : yes
-0------ Discontinous Transmission was not used --010100 RXLEV-FULL-SERVING-CELL= (-110 + 20) dB
14 0------- spare : 0 -0------ MEAS-VALID : yes --010100 RXLEV-SUB-SERVING-CELL = (-110 + 20) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 101 Number of neighbouring cell measurements = 5
010100 RXLEV-Neighbour-CELL 1 = (-110 + 20) dB 00001 BCCH-FREQ-NCELL 1 : 1 011101 Base station identity code of the 1'th neighbouring cell = 29
010011 RXLEV-Neighbour-CELL 2 = (-110 + 19) dB 01001 BCCH-FREQ-NCELL 2 : 9 011010 Base station identity code of the 2'th neighbouring cell= 26
001100 RXLEV-Neighbour-CELL 3 = (-110 + 12) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001010 RXLEV-Neighbour-CELL 4 = (-110 + 10) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001001 RXLEV-Neighbour-CELL 5 = (-110 + 9) dB 00011 BCCH-FREQ-NCELL 5 : 3 011110 Base station identity code of the 5'th neighbouring cell = 30
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 23 ]___[ 11:52:47,566 ]___[ DOWN ]____[ SDCCH ]______________________________
06 35 11
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
35 00110101 MESSAGE TYPE : CIPHERING MODE COMMAND
11 ----000- cipher with algorithm A5/1 -------1 Start ciphering 000----- spare : 0 ---1---- Cipher Response : IMEISV shall be included
_____[ 24 ]___[ 11:52:47,566 ]___[ UP ]___________________________________________
06 32 17 09 33 23 81 81 32 07 31 09 f0
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages32 00110010 MESSAGE TYPE : CIPHERING MODE COMPLETE
17 00010111 INFORMATIONS ELEMENT: Mobile Identity
09 00001001 length of Mob.ident.3: 9
33 ----0--- No. of ID digits : even -----011 Type of identity : IMEISV
0011---- Identity Digit 1 : 323 ----0011 Identity Digit 2 : 3 0010---- Identity Digit 3 : 2 81 ----0001 Identity Digit 4 : 1 1000---- Identity Digit 5 : 8 81 ----0001 Identity Digit 6 : 1 1000---- Identity Digit 7 : 8 32 ----0010 Identity Digit 8 : 2 0011---- Identity Digit 9 : 3 07 ----0111 Identity Digit 10 : 7 0000---- Identity Digit 11 : 0 31 ----0001 Identity Digit 12 : 1 0011---- Identity Digit 13 : 3 09 ----1001 Identity Digit 14 : 9 0000---- Identity Digit 15 : 0 f0 ----0000 Identity Digit 16 : 0 1111---- Identity Digit 17 : 15
_____[ 25 ]___[ 11:52:47,863 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 26 ]___[ 11:52:47,914 ]___[ UP ]___________________________________________
06 15 97 17 01 55 4b 49 05 d3 00 e9 47 7c 81 bc 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
97 1------- BA used : yes
-0------ Discontinous Transmission was not used --010111 RXLEV-FULL-SERVING-CELL= (-110 + 23) dB
17 0------- spare : 0 -0------ MEAS-VALID : yes --010111 RXLEV-SUB-SERVING-CELL = (-110 + 23) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 101 Number of neighbouring cell measurements = 5
010101 RXLEV-Neighbour-CELL 1 = (-110 + 21) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010010 RXLEV-Neighbour-CELL 2 = (-110 + 18) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001100 RXLEV-Neighbour-CELL 3 = (-110 + 12) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001010 RXLEV-Neighbour-CELL 4 = (-110 + 10) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001000 RXLEV-Neighbour-CELL 5 = (-110 + 8) dB 00011 BCCH-FREQ-NCELL 5 : 3 011110 Base station identity code of the 5'th neighbouring cell = 30
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 27 ]___[ 11:52:48,258 ]___[ DOWN ]____[ SDCCH ]______________________________
13 05 04 01 a0 5c 09 11 81 94 33 57 12 80 51 f6 7d 02 91 81
13 0------- direction from : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages05 00------ SendSequenceNumber : 0
--000101 MESSAGE TYPE : SETUP
04 00000100 INFORMATION ELEMENT : Bearer capability01 00000001 length : 1a0 1------- Extension : 1 -01----- Radio Channel Req. : full rate support only MS ---0---- Coding Standard : GSM standard coding ----0--- Transfer Mode : Circuit Mode -----000 Info Transfer Cap. : speech
5c 01011100 INFORMATION ELEMENT : Calling party BCD number09 00001001 length : 911 0------- Extension : 0 -001---- Type of number : international number ----0001 Numb. plan id. : ISDN/telephony numb. pl. (Rec. E.164/E.163)81 1------- Extension : 1 -00----- Present.indic. : Presentation allowed ---000-- spare : 0 ------01 Present.indic. : User-provided, verified and passed94..f6 number : 4933752108156
7d 01111101 INFORMATION ELEMENT : High Layer Compatibility02 00000010 length : 291 1------- Extension : 1 -00----- Coding standard : CCITT standardized coding ---100-- Interpret.i.ch. : First high layer char.id. to be used ------01 Present.method : High Layer protocol profile81 10000001 High layer char. : Telephony
_____[ 28 ]___[ 11:52:48,258 ]___[ UP ]___________________________________________
93 08 04 04 60 02 00 81
93 1------- direction to : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages08 00------ SendSequenceNumber : 0
--001000 MESSAGE TYPE : CALL CONFIRMED
04 00000100 INFORMATION ELEMENT : Bearer capability04 00000100 length : 460 0------- Extension : 0
-11----- Radio Channel Req. : dual rate support MS/full rate preferred ---0---- Coding Standard : GSM standard coding ----0--- Transfer Mode : Circuit Mode -----000 Info Transfer Cap. : speech02 0------- Extension : 0 -0------ Coding : octet used for extension of inf. transf. capab. --00---- Spare : 00 ----0010 speech Vers. indic. : GSM full rate speech version 200 0------- Extension : 0 -0------ Coding : octet used for extension of inf. transf. capab. --00---- Spare : 00 ----0000 speech Vers. indic. : GSM full rate speech version 181 1------- Extension : 1 -0------ Coding : octet used for extension of inf. transf. capab. --00---- Spare : 00 ----0001 speech Vers. indic. : GSM half rate speech version 1
_____[ 29 ]___[ 11:52:48,336 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 30 ]___[ 11:52:48,387 ]___[ UP ]___________________________________________
06 15 96 16 01 96 4b 47 85 d3 06 f1 60 74 a3 be 49 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
96 1------- BA used : yes -0------ Discontinous Transmission was not used --010110 RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
16 0------- spare : 0 -0------ MEAS-VALID : yes --010110 RXLEV-SUB-SERVING-CELL = (-110 + 22) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
010110 RXLEV-Neighbour-CELL 1 = (-110 + 22) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001111 RXLEV-Neighbour-CELL 2 = (-110 + 15) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001100 RXLEV-Neighbour-CELL 3 = (-110 + 12) dB 00011 BCCH-FREQ-NCELL 3 : 3 011110 Base station identity code of the 3'th neighbouring cell = 30
001011 RXLEV-Neighbour-CELL 4 = (-110 + 11) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
001010 RXLEV-Neighbour-CELL 5 = (-110 + 10) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
001001 RXLEV-Neighbour-CELL 6 = (-110 + 9) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 31 ]___[ 11:52:48,809 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6
f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 32 ]___[ 11:52:48,855 ]___[ UP ]___________________________________________
06 15 96 16 01 8e 4b 47 0d e3 82 e9 87 7c b2 b8 40 1d
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
96 1------- BA used : yes -0------ Discontinous Transmission was not used --010110 RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
16 0------- spare : 0 -0------ MEAS-VALID : yes --010110 RXLEV-SUB-SERVING-CELL = (-110 + 22) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
001110 RXLEV-Neighbour-CELL 1 = (-110 + 14) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001110 RXLEV-Neighbour-CELL 2 = (-110 + 14) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001110 RXLEV-Neighbour-CELL 3 = (-110 + 14) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001100 RXLEV-Neighbour-CELL 4 = (-110 + 12) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001011 RXLEV-Neighbour-CELL 5 = (-110 + 11) dB 00101 BCCH-FREQ-NCELL 5 : 5 011100 Base station identity code of the 5'th neighbouring cell = 28
001000 RXLEV-Neighbour-CELL 6 = (-110 + 8) dB 00000 BCCH-FREQ-NCELL 6 : 0 011101 Base station identity code of the 6'th neighbouring cellt = = 29
_____[ 33 ]___[ 11:52:49,219 ]___[ DOWN ]____[ SDCCH ]______________________________
06 2e 0d 90 40 05 05 05 8c 07 10 24 70 63 21
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
2e 00101110 MESSAGE TYPE : ASSIGNMENT COMMAND
: Channel Description 20d 00001--- Channel type and TDMA offset = TCH/F + ACCHs -----101 Timslot number : 5
90 100----- Training sequ. code : 4 ---1---- Hopping Channel ----0000 MAIO high part40 01------ MAIO low part --000000 Hopping Sequence Nr.: HSN = 0
: POWER LEVEL05 000----- spare ---00101 Power level : 5
05 00000101 INFORMATION ELEMENT : FREQUENCY LIST05 00000101 length : 58c 10--110- Range 128 format --00---- spare -------0 Orig ARFCN high07 00000111 ORIG-ARFCN (middle part)10 0------- Orig ARFCN low -0010000 W1 high part24 0------- W1 low part -010010- W2 -------0 W3 high part70 01110--- W3 low part -----000 W4 high part
63 01100011 INFORMATION ELEMENT : CHANNEL MODE21 00100001 channel mode : speech full rate or half rate version 2
_____[ 34 ]___[ 11:52:49,219 ]___[ UP ]___________________________________________
06 29 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
29 00101001 MESSAGE TYPE : ASSIGNMENT COMPLETE
00 00000000 RR-Cause (reason of event) = Normal event
_____[ 35 ]___[ 11:52:49,398 ]___[ UP ]____[ FACCH_F ]______________________________
93 01
93 1------- direction to : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages01 00------ SendSequenceNumber : 0
--000001 MESSAGE TYPE : ALERTING
_____[ 36 ]___[ 11:52:50,059 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 37 ]___[ 11:52:50,066 ]___[ UP ]___________________________________________
06 15 d3 13 49 97 4b 47 81 d3 82 e9 83 78 c3 be 51 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d3 1------- BA used : yes -1------ Discontinous Transmission was used --010011 RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13 0------- spare : 0 -0------ MEAS-VALID : yes --010011 RXLEV-SUB-SERVING-CELL = (-110 + 19) dB 0------ spare : 0 -100--- RX-QUAL-FULL-SERVING-CELL = ~2,26% error bit ----100 RX-QUAL-SUB -SERVING-CELL = ~2,26% error bit 110 Number of neighbouring cell measurements = 6
010111 RXLEV-Neighbour-CELL 1 = (-110 + 23) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001111 RXLEV-Neighbour-CELL 2 = (-110 + 15) dB 00000 BCCH-FREQ-NCELL 2 : 0 011101 Base station identity code of the 2'th neighbouring cell= 29
001110 RXLEV-Neighbour-CELL 3 = (-110 + 14) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001100 RXLEV-Neighbour-CELL 4 = (-110 + 12) dB 00011 BCCH-FREQ-NCELL 4 : 3 011110 Base station identity code of the 4'th neighbouring cell = 30
001100 RXLEV-Neighbour-CELL 5 = (-110 + 12) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
001010 RXLEV-Neighbour-CELL 6 = (-110 + 10) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 38 ]___[ 11:52:50,551 ]___[ UP ]____[ SACCH ]______________________________
06 15 d5 16 6d 9b 4b 4a 15 c4 c6 f2 61 75 20 3a 79 df
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d5 1------- BA used : yes -1------ Discontinous Transmission was used --010101 RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
16 0------- spare : 0 -0------ MEAS-VALID : yes --010110 RXLEV-SUB-SERVING-CELL = (-110 + 22) dB 0------ spare : 0 -110--- RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit ----110 RX-QUAL-SUB -SERVING-CELL = ~9,05% error bit 110 Number of neighbouring cell measurements = 6
011011 RXLEV-Neighbour-CELL 1 = (-110 + 27) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010100 RXLEV-Neighbour-CELL 2 = (-110 + 20) dB 00101 BCCH-FREQ-NCELL 2 : 5 011100 Base station identity code of the 2'th neighbouring cell= 28
010011 RXLEV-Neighbour-CELL 3 = (-110 + 19) dB 00011 BCCH-FREQ-NCELL 3 : 3 011110 Base station identity code of the 3'th neighbouring cell = 30
010011 RXLEV-Neighbour-CELL 4 = (-110 + 19) dB 00001 BCCH-FREQ-NCELL 4 : 1 011101 Base station identity code of the 4'th neighbouring cell = 29
010010 RXLEV-Neighbour-CELL 5 = (-110 + 18) dB 00000 BCCH-FREQ-NCELL 5 : 0 011101 Base station identity code of the 5'th neighbouring cell = 29
001111 RXLEV-Neighbour-CELL 6 = (-110 + 15) dB 00111 BCCH-FREQ-NCELL 6 : 7 011111 Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 39 ]___[ 11:52:51,031 ]___[ UP ]____[ SACCH ]______________________________
06 15 d8 17 6d 9f 4b 4b 05 d5 00 ea 47 7d 11 bc 81 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d8 1------- BA used : yes -1------ Discontinous Transmission was used --011000 RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
17 0------- spare : 0 -0------ MEAS-VALID : yes --010111 RXLEV-SUB-SERVING-CELL = (-110 + 23) dB 0------ spare : 0 -110--- RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit ----110 RX-QUAL-SUB -SERVING-CELL = ~9,05% error bit 110 Number of neighbouring cell measurements = 6
011111 RXLEV-Neighbour-CELL 1 = (-110 + 31) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010110 RXLEV-Neighbour-CELL 2 = (-110 + 22) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
010100 RXLEV-Neighbour-CELL 3 = (-110 + 20) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
010010 RXLEV-Neighbour-CELL 4 = (-110 + 18) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
010001 RXLEV-Neighbour-CELL 5 = (-110 + 17) dB 00011 BCCH-FREQ-NCELL 5 : 3 011110 Base station identity code of the 5'th neighbouring cell = 30
010000 RXLEV-Neighbour-CELL 6 = (-110 + 16) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 40 ]___[ 11:52:51,488 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 41 ]___[ 11:52:51,512 ]___[ UP ]___________________________________________
06 15 d4 13 69 9c 4b 49 05 d3 80 e9 a7 7c d2 b8 58 de
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d4 1------- BA used : yes -1------ Discontinous Transmission was used --010100 RXLEV-FULL-SERVING-CELL= (-110 + 20) dB
13 0------- spare : 0 -0------ MEAS-VALID : yes --010011 RXLEV-SUB-SERVING-CELL = (-110 + 19) dB 0------ spare : 0 -110--- RX-QUAL-FULL-SERVING-CELL = ~9,05% error bit ----100 RX-QUAL-SUB -SERVING-CELL = ~2,26% error bit 110 Number of neighbouring cell measurements = 6
011100 RXLEV-Neighbour-CELL 1 = (-110 + 28) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010010 RXLEV-Neighbour-CELL 2 = (-110 + 18) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001110 RXLEV-Neighbour-CELL 3 = (-110 + 14) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001101 RXLEV-Neighbour-CELL 4 = (-110 + 13) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001101 RXLEV-Neighbour-CELL 5 = (-110 + 13) dB 00101 BCCH-FREQ-NCELL 5 : 5 011100 Base station identity code of the 5'th neighbouring cell = 28
001011 RXLEV-Neighbour-CELL 6 = (-110 + 11) dB 00011 BCCH-FREQ-NCELL 6 : 3 011110 Base station identity code of the 6'th neighbouring cellt = = 30
_____[ 42 ]___[ 11:52:51,973 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85
c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 43 ]___[ 11:52:51,992 ]___[ UP ]___________________________________________
06 15 d1 10 37 a1 4b 47 0d e3 02 e8 e0 74 73 be 39 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d1 1------- BA used : yes -1------ Discontinous Transmission was used --010001 RXLEV-FULL-SERVING-CELL= (-110 + 17) dB
10 0------- spare : 0 -0------ MEAS-VALID : yes --010000 RXLEV-SUB-SERVING-CELL = (-110 + 16) dB 0------ spare : 0 -011--- RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit ----011 RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit 110 Number of neighbouring cell measurements = 6
100001 RXLEV-Neighbour-CELL 1 = (-110 + 33) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001110 RXLEV-Neighbour-CELL 2 = (-110 + 14) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001100 RXLEV-Neighbour-CELL 3 = (-110 + 12) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 4 = (-110 + 7) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 5 = (-110 + 7) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
000111 RXLEV-Neighbour-CELL 6 = (-110 + 7) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 44 ]___[ 11:52:52,453 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 45 ]___[ 11:52:52,473 ]___[ UP ]___________________________________________
06 15 d5 17 31 a2 4b 49 0d e3 42 e9 05 70 70 3a 39 df
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d5 1------- BA used : yes -1------ Discontinous Transmission was used --010101 RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
17 0------- spare : 0 -0------ MEAS-VALID : yes --010111 RXLEV-SUB-SERVING-CELL = (-110 + 23) dB 0------ spare : 0 -011--- RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100010 RXLEV-Neighbour-CELL 1 = (-110 + 34) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010010 RXLEV-Neighbour-CELL 2 = (-110 + 18) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001101 RXLEV-Neighbour-CELL 3 = (-110 + 13) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001000 RXLEV-Neighbour-CELL 4 = (-110 + 8) dB 00101 BCCH-FREQ-NCELL 4 : 5 011100 Base station identity code of the 4'th neighbouring cell = 28
000111 RXLEV-Neighbour-CELL 5 = (-110 + 7) dB 00000 BCCH-FREQ-NCELL 5 : 0 011101 Base station identity code of the 5'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 6 = (-110 + 7) dB 00111 BCCH-FREQ-NCELL 6 : 7 011111 Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 46 ]___[ 11:52:52,934 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 47 ]___[ 11:52:52,953 ]___[ UP ]___________________________________________
06 15 d3 13 01 a7 4b 49 8d e2 82 e9 00 74 72 b8 21 df
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d3 1------- BA used : yes -1------ Discontinous Transmission was used --010011 RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13 0------- spare : 0 -0------ MEAS-VALID : yes --010011 RXLEV-SUB-SERVING-CELL = (-110 + 19) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100111 RXLEV-Neighbour-CELL 1 = (-110 + 39) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010011 RXLEV-Neighbour-CELL 2 = (-110 + 19) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001010 RXLEV-Neighbour-CELL 3 = (-110 + 10) dB
00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001000 RXLEV-Neighbour-CELL 4 = (-110 + 8) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 5 = (-110 + 7) dB 00101 BCCH-FREQ-NCELL 5 : 5 011100 Base station identity code of the 5'th neighbouring cell = 28
000100 RXLEV-Neighbour-CELL 6 = (-110 + 4) dB 00111 BCCH-FREQ-NCELL 6 : 7 011111 Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 48 ]___[ 11:52:53,371 ]___[ UP ]____[ SACCH ]______________________________
93 07
93 1------- direction to : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages07 00------ SendSequenceNumber : 0
--000111 MESSAGE TYPE : CONNECT
_____[ 49 ]___[ 11:52:53,434 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 50 ]___[ 11:52:53,434 ]___[ UP ]___________________________________________
06 15 d3 15 01 a4 4b 4a 8d e2 40 e9 21 74 73 be 39 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d3 1------- BA used : yes -1------ Discontinous Transmission was used --010011 RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
15 0------- spare : 0 -0------ MEAS-VALID : yes --010101 RXLEV-SUB-SERVING-CELL = (-110 + 21) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100100 RXLEV-Neighbour-CELL 1 = (-110 + 36) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010101 RXLEV-Neighbour-CELL 2 = (-110 + 21) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001001 RXLEV-Neighbour-CELL 3 = (-110 + 9) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001001 RXLEV-Neighbour-CELL 4 = (-110 + 9) dB 00001 BCCH-FREQ-NCELL 4 : 1 011101 Base station identity code of the 4'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 5 = (-110 + 7) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
000111 RXLEV-Neighbour-CELL 6 = (-110 + 7) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 51 ]___[ 11:52:53,703 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 0f
13 0------- direction from : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages0f 00------ SendSequenceNumber : 0
--001111 MESSAGE TYPE :CONNECT ACKNOWLEDGE
_____[ 52 ]___[ 11:52:53,895 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format
--0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 53 ]___[ 11:52:53,902 ]___[ UP ]___________________________________________
06 15 98 1a 01 a4 4b 4b 8d e3 82 e9 20 74 82 b8 39 df
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
98 1------- BA used : yes -0------ Discontinous Transmission was not used --011000 RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
1a 0------- spare : 0 -0------ MEAS-VALID : yes --011010 RXLEV-SUB-SERVING-CELL = (-110 + 26) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100100 RXLEV-Neighbour-CELL 1 = (-110 + 36) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010111 RXLEV-Neighbour-CELL 2 = (-110 + 23) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001110 RXLEV-Neighbour-CELL 3 = (-110 + 14) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001001 RXLEV-Neighbour-CELL 4 = (-110 + 9) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
001000 RXLEV-Neighbour-CELL 5 = (-110 + 8) dB 00101 BCCH-FREQ-NCELL 5 : 5 011100 Base station identity code of the 5'th neighbouring cell = 28
000111 RXLEV-Neighbour-CELL 6 = (-110 + 7) dB 00111 BCCH-FREQ-NCELL 6 : 7 011111 Base station identity code of the 6'th neighbouring cellt = = 31
_____[ 54 ]___[ 11:53:00,441 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 55 ]___[ 11:53:00,449 ]___[ UP ]___________________________________________
06 15 96 14 01 a0 4b 47 8d e3 02 e8 e7 7c 72 b8 28 1d
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
96 1------- BA used : yes -0------ Discontinous Transmission was not used --010110 RXLEV-FULL-SERVING-CELL= (-110 + 22) dB
14 0------- spare : 0 -0------ MEAS-VALID : yes --010100 RXLEV-SUB-SERVING-CELL = (-110 + 20) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100000 RXLEV-Neighbour-CELL 1 = (-110 + 32) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001111 RXLEV-Neighbour-CELL 2 = (-110 + 15) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001100 RXLEV-Neighbour-CELL 3 = (-110 + 12) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
000111 RXLEV-Neighbour-CELL 4 = (-110 + 7) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
000111 RXLEV-Neighbour-CELL 5 = (-110 + 7) dB 00101 BCCH-FREQ-NCELL 5 : 5 011100 Base station identity code of the 5'th neighbouring cell = 28
000101 RXLEV-Neighbour-CELL 6 = (-110 + 5) dB 00000 BCCH-FREQ-NCELL 6 : 0 011101 Base station identity code of the 6'th neighbouring cellt = = 29
_____[ 56 ]___[ 11:53:00,922 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 57 ]___[ 11:53:00,941 ]___[ UP ]___________________________________________
06 15 8f 0e 4b a2 4b 46 85 d2 4e f8 e3 78 60 3a 29 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
8f 1------- BA used : yes -0------ Discontinous Transmission was not used --001111 RXLEV-FULL-SERVING-CELL= (-110 + 15) dB
0e 0------- spare : 0 -0------ MEAS-VALID : yes --001110 RXLEV-SUB-SERVING-CELL = (-110 + 14) dB 0------ spare : 0 -100--- RX-QUAL-FULL-SERVING-CELL = ~2,26% error bit ----101 RX-QUAL-SUB -SERVING-CELL = ~4,53% error bit 110 Number of neighbouring cell measurements = 6
100010 RXLEV-Neighbour-CELL 1 = (-110 + 34) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001101 RXLEV-Neighbour-CELL 2 = (-110 + 13) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001001 RXLEV-Neighbour-CELL 3 = (-110 + 9) dB 00111 BCCH-FREQ-NCELL 3 : 7 011111 Base station identity code of the 3'th neighbouring cell = 31
000111 RXLEV-Neighbour-CELL 4 = (-110 + 7) dB 00011 BCCH-FREQ-NCELL 4 : 3 011110 Base station identity code of the 4'th neighbouring cell = 30
000110 RXLEV-Neighbour-CELL 5 = (-110 + 6) dB 00000 BCCH-FREQ-NCELL 5 : 0 011101 Base station identity code of the 5'th neighbouring cell = 29
000101 RXLEV-Neighbour-CELL 6 = (-110 + 5) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 58 ]___[ 11:53:01,402 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 59 ]___[ 11:53:01,410 ]___[ UP ]___________________________________________
06 15 ce 0e 37 9e 4b 48 85 d2 80 e9 27 7c 81 bc 31 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
ce 1------- BA used : yes -1------ Discontinous Transmission was used --001110 RXLEV-FULL-SERVING-CELL= (-110 + 14) dB
0e 0------- spare : 0 -0------ MEAS-VALID : yes --001110 RXLEV-SUB-SERVING-CELL = (-110 + 14) dB 0------ spare : 0 -011--- RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit ----011 RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit 110 Number of neighbouring cell measurements = 6
011110 RXLEV-Neighbour-CELL 1 = (-110 + 30) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010001 RXLEV-Neighbour-CELL 2 = (-110 + 17) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001010 RXLEV-Neighbour-CELL 3 = (-110 + 10) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001001 RXLEV-Neighbour-CELL 4 = (-110 + 9) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001000 RXLEV-Neighbour-CELL 5 = (-110 + 8) dB 00011 BCCH-FREQ-NCELL 5 : 3 011110 Base station identity code of the 5'th neighbouring cell = 30
000110 RXLEV-Neighbour-CELL 6 = (-110 + 6) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 60 ]___[ 11:53:01,883 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 61 ]___[ 11:53:01,891 ]___[ UP ]___________________________________________
06 15 8f 0f 37 9b 4b 47 85 d3 86 f1 40 74 93 be 31 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
8f 1------- BA used : yes -0------ Discontinous Transmission was not used --001111 RXLEV-FULL-SERVING-CELL= (-110 + 15) dB
0f 0------- spare : 0 -0------ MEAS-VALID : yes --001111 RXLEV-SUB-SERVING-CELL = (-110 + 15) dB 0------ spare : 0 -011--- RX-QUAL-FULL-SERVING-CELL = ~1,13% error bit ----011 RX-QUAL-SUB -SERVING-CELL = ~1,13% error bit 110 Number of neighbouring cell measurements = 6
011011 RXLEV-Neighbour-CELL 1 = (-110 + 27) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001111 RXLEV-Neighbour-CELL 2 = (-110 + 15) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001110 RXLEV-Neighbour-CELL 3 = (-110 + 14) dB 00011 BCCH-FREQ-NCELL 3 : 3 011110 Base station identity code of the 3'th neighbouring cell = 30
001010 RXLEV-Neighbour-CELL 4 = (-110 + 10) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
001001 RXLEV-Neighbour-CELL 5 = (-110 + 9) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
000110 RXLEV-Neighbour-CELL 6 = (-110 + 6) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 62 ]___[ 11:53:02,363 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15
10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 63 ]___[ 11:53:02,371 ]___[ UP ]___________________________________________
06 15 91 11 15 9b 4b 47 05 d2 c0 e9 63 78 a3 be 31 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
91 1------- BA used : yes -0------ Discontinous Transmission was not used --010001 RXLEV-FULL-SERVING-CELL= (-110 + 17) dB
11 0------- spare : 0 -0------ MEAS-VALID : yes --010001 RXLEV-SUB-SERVING-CELL = (-110 + 17) dB 0------ spare : 0 -001--- RX-QUAL-FULL-SERVING-CELL = ~0,28% error bit ----010 RX-QUAL-SUB -SERVING-CELL = ~0,57% error bit 110 Number of neighbouring cell measurements = 6
011011 RXLEV-Neighbour-CELL 1 = (-110 + 27) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
001110 RXLEV-Neighbour-CELL 2 = (-110 + 14) dB 00001 BCCH-FREQ-NCELL 2 : 1 011101 Base station identity code of the 2'th neighbouring cell= 29
001011 RXLEV-Neighbour-CELL 3 = (-110 + 11) dB 00000 BCCH-FREQ-NCELL 3 : 0 011101 Base station identity code of the 3'th neighbouring cell = 29
001011 RXLEV-Neighbour-CELL 4 = (-110 + 11) dB 00011 BCCH-FREQ-NCELL 4 : 3 011110 Base station identity code of the 4'th neighbouring cell = 30
001010 RXLEV-Neighbour-CELL 5 = (-110 + 10) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
000110 RXLEV-Neighbour-CELL 6 = (-110 + 6) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 64 ]___[ 11:53:02,844 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 04 10 00 00 00 00 00 c0 82 9d 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
04 -----1-- BCCH alloc. RF chan.: 9110 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3982 1------- BCCH alloc. RF chan.: 32 ------1- BCCH alloc. RF chan.: 269d 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 ----1--- BCCH alloc. RF chan.: 20 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 65 ]___[ 11:53:02,855 ]___[ UP ]___________________________________________
06 15 93 13 11 9f 4b 48 8d e3 c2 e9 60 74 b3 be 29 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
93 1------- BA used : yes -0------ Discontinous Transmission was not used --010011 RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13 0------- spare : 0 -0------ MEAS-VALID : yes --010011 RXLEV-SUB-SERVING-CELL = (-110 + 19) dB 0------ spare : 0 -001--- RX-QUAL-FULL-SERVING-CELL = ~0,28% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
011111 RXLEV-Neighbour-CELL 1 = (-110 + 31) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010001 RXLEV-Neighbour-CELL 2 = (-110 + 17) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
001111 RXLEV-Neighbour-CELL 3 = (-110 + 15) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001011 RXLEV-Neighbour-CELL 4 = (-110 + 11) dB 00000 BCCH-FREQ-NCELL 4 : 0 011101 Base station identity code of the 4'th neighbouring cell = 29
001011 RXLEV-Neighbour-CELL 5 = (-110 + 11) dB 00111 BCCH-FREQ-NCELL 5 : 7 011111 Base station identity code of the 5'th neighbouring cell = 31
000101 RXLEV-Neighbour-CELL 6 = (-110 + 5) dB
00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 66 ]___[ 11:53:03,324 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e cd 3a 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity cd 11001101 Cell identity value1, Hex Wert3a 00111010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 67 ]___[ 11:53:03,336 ]___[ UP ]___________________________________________
06 15 d3 13 01 a2 4b 4a 8d e4 42 e9 87 7c a0 3a 21 5c
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
d3 1------- BA used : yes -1------ Discontinous Transmission was used --010011 RXLEV-FULL-SERVING-CELL= (-110 + 19) dB
13 0------- spare : 0 -0------ MEAS-VALID : yes --010011 RXLEV-SUB-SERVING-CELL = (-110 + 19) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 110 Number of neighbouring cell measurements = 6
100010 RXLEV-Neighbour-CELL 1 = (-110 + 34) dB 01001 BCCH-FREQ-NCELL 1 : 9 011010 Base station identity code of the 1'th neighbouring cell = 26
010101 RXLEV-Neighbour-CELL 2 = (-110 + 21) dB 00011 BCCH-FREQ-NCELL 2 : 3 011110 Base station identity code of the 2'th neighbouring cell= 30
010001 RXLEV-Neighbour-CELL 3 = (-110 + 17) dB 00001 BCCH-FREQ-NCELL 3 : 1 011101 Base station identity code of the 3'th neighbouring cell = 29
001100 RXLEV-Neighbour-CELL 4 = (-110 + 12) dB 00111 BCCH-FREQ-NCELL 4 : 7 011111 Base station identity code of the 4'th neighbouring cell = 31
001010 RXLEV-Neighbour-CELL 5 = (-110 + 10) dB 00000 BCCH-FREQ-NCELL 5 : 0 011101 Base station identity code of the 5'th neighbouring cell = 29
000100 RXLEV-Neighbour-CELL 6 = (-110 + 4) dB 00101 BCCH-FREQ-NCELL 6 : 5 011100 Base station identity code of the 6'th neighbouring cellt = = 28
_____[ 68 ]___[ 11:53:03,664 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2b 1a 55 0e 40 62 0e 05
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages2b 00101011 MESSAGE TYPE : HANDOVER COMMAND
: Celldescription1a --011--- PLMN Colour Code NCC: 3 -----010 BS Colour code BCC : 2 00------ BCCH ARFCN high part: 055 01010101 BCCH ARFCN low part : 85
: Channel Description 20e 00001--- Channel type and TDMA offset = TCH/F + ACCHs -----110 Timslot number : 6
40 010----- Training sequ. code : 2 ---000-- Single channel : RF single channel ------00 Sgl RF chan.high prt: 0 62 01100010 abs.RFchan. low part: 98
: Handover Reference0e 00001110 Handover refer. val.: 14
: Power Command and Access Type05 0------- Sending of Handover access is mandatory -00----- spare ---00101 Power Level : 5
_____[ 69 ]___[ 11:53:03,734 ]___[ UP ]____[ FACCH_F ]______________________________
06 2c 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages2c 00101100 MESSAGE TYPE : HANDOVER COMPLETE
: RR Cause00 00000000 Normal event
_____[ 70 ]___[ 11:53:03,773 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2d 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages2d 00101101 MESSAGE TYPE : PHYSICAL INFORMATION
: Timing Advance00 00------ spare --000000 Timing advance value: 0 x 48/13 sec
_____[ 71 ]___[ 11:53:03,844 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 2d 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages2d 00101101 MESSAGE TYPE : PHYSICAL INFORMATION
: Timing Advance00 00------ spare --000000 Timing advance value: 0 x 48/13 sec
_____[ 72 ]___[ 11:53:04,137 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3920 --1----- BCCH alloc. RF chan.: 3095 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 73 ]___[ 11:53:04,145 ]___[ UP ]___________________________________________
06 15 95 19 00 d5 0b a4 15 f1 84 f0 00 00 00 00 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
95 1------- BA used : yes -0------ Discontinous Transmission was not used --010101 RXLEV-FULL-SERVING-CELL= (-110 + 21) dB
19 0------- spare : 0 -0------ MEAS-VALID : yes --011001 RXLEV-SUB-SERVING-CELL = (-110 + 25) dB 0------ spare : 0
-000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 011 Number of neighbouring cell measurements = 3
010101 RXLEV-Neighbour-CELL 1 = (-110 + 21) dB 00001 BCCH-FREQ-NCELL 1 : 1 011101 Base station identity code of the 1'th neighbouring cell = 29
001000 RXLEV-Neighbour-CELL 2 = (-110 + 8) dB 00101 BCCH-FREQ-NCELL 2 : 5 011111 Base station identity code of the 2'th neighbouring cell= 31
000110 RXLEV-Neighbour-CELL 3 = (-110 + 6) dB 00010 BCCH-FREQ-NCELL 3 : 2 011110 Base station identity code of the 3'th neighbouring cell = 30
000000 RXLEV-Neighbour-CELL 4 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 4 : 0 000000 Base station identity code of the 4'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 5 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 5 : 0 000000 Base station identity code of the 5'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 74 ]___[ 11:53:04,617 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3920 --1----- BCCH alloc. RF chan.: 3095 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 75 ]___[ 11:53:04,625 ]___[ UP ]___________________________________________
06 15 de 1f 00 d5 0b a5 89 e2 0a f8 00 00 00 00 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
de 1------- BA used : yes -1------ Discontinous Transmission was used --011110 RXLEV-FULL-SERVING-CELL= (-110 + 30) dB
1f 0------- spare : 0
-0------ MEAS-VALID : yes --011111 RXLEV-SUB-SERVING-CELL = (-110 + 31) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 011 Number of neighbouring cell measurements = 3
010101 RXLEV-Neighbour-CELL 1 = (-110 + 21) dB 00001 BCCH-FREQ-NCELL 1 : 1 011101 Base station identity code of the 1'th neighbouring cell = 29
001011 RXLEV-Neighbour-CELL 2 = (-110 + 11) dB 00010 BCCH-FREQ-NCELL 2 : 2 011110 Base station identity code of the 2'th neighbouring cell= 30
001000 RXLEV-Neighbour-CELL 3 = (-110 + 8) dB 00101 BCCH-FREQ-NCELL 3 : 5 011111 Base station identity code of the 3'th neighbouring cell = 31
000000 RXLEV-Neighbour-CELL 4 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 4 : 0 000000 Base station identity code of the 4'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 5 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 5 : 0 000000 Base station identity code of the 5'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 76 ]___[ 11:53:05,008 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 25 02 e0 90
13 0------- direction from : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages25 00------ SendSequenceNumber : 0
--100101 MESSAGE TYPE : DISCONNECT
02 00000010 LENGTH OF IE CAUSE : 2e0 1------- Extension Bit : 1 -11----- Coding stand. : Standard defined for the GSM-PLMNS ---0---- spare : 0 ----0000 location : user 90 -0010000 cause : Normal call clearing
_____[ 77 ]___[ 11:53:05,008 ]___[ UP ]___________________________________________
93 2d
93 1------- direction to : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages2d 00------ SendSequenceNumber : 0
--101101 MESSAGE TYPE : RELEASE
_____[ 78 ]___[ 11:53:05,098 ]___[ DOWN ]____[ SACCH ]______________________________
06 1e aa b2 62 f2 10 31 04 55 08 2b 2b 2b 2b 2b 2b 2b 00 00 08 1a
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1e 00011110 MESSAGE TYPE : SYSTEM INFORMATION TYPE 6
: Cell Identity aa 10101010 Cell identity value1, Hex Wertb2 10110010 Cell identity value2, Hex Wert
: Location Area Identification 62 ----0010 MCC digit 1 : 2 0110---- MCC digit 2 : 6 f2 ----0010 MCC digit 3 : 2
1111---- MNC digit 3 : 15 10 ----0000 MNC digit 1 : 0 0001---- MNC digit 2 : 1
31 00110001 Location area code (LAI), Number of MSC04 00000100 Location area code (LAI), Number of BSC
: Cell Options (SACH) 55 0------- 1 spare bit : 0 -1------ Power control indic.: is set --01---- MSs shall use uplink discont.transmission ----0101 Radio Link Timeout : 24
: NCC Permitted08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
_____[ 79 ]___[ 11:53:05,105 ]___[ UP ]___________________________________________
06 15 9f 1f 00 d4 0b a6 15 f2 c4 f0 00 00 00 00 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
9f 1------- BA used : yes -0------ Discontinous Transmission was not used --011111 RXLEV-FULL-SERVING-CELL= (-110 + 31) dB
1f 0------- spare : 0 -0------ MEAS-VALID : yes --011111 RXLEV-SUB-SERVING-CELL = (-110 + 31) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 011 Number of neighbouring cell measurements = 3
010100 RXLEV-Neighbour-CELL 1 = (-110 + 20) dB 00001 BCCH-FREQ-NCELL 1 : 1 011101 Base station identity code of the 1'th neighbouring cell = 29
001100 RXLEV-Neighbour-CELL 2 = (-110 + 12) dB 00101 BCCH-FREQ-NCELL 2 : 5 011111 Base station identity code of the 2'th neighbouring cell= 31
001011 RXLEV-Neighbour-CELL 3 = (-110 + 11) dB 00010 BCCH-FREQ-NCELL 3 : 2 011110 Base station identity code of the 3'th neighbouring cell = 30
000000 RXLEV-Neighbour-CELL 4 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 4 : 0 000000 Base station identity code of the 4'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 5 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 5 : 0 000000 Base station identity code of the 5'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 80 ]___[ 11:53:05,328 ]___[ DOWN ]____[ FACCH_F ]______________________________
13 2a 08 02 e0 90
13 0------- direction from : originating site -001---- TransactionID : 1 ----0011 Protocol Discrim. : Call control and call related SS messages2a 00------ SendSequenceNumber : 0
--101010 MESSAGE TYPE : RELEASE COMPLETE
08 00001000 INFORMATION ELEMENT : Cause02 00000010 LENGTH OF IE CAUSE : 2e0 1------- Extension Bit : 1 -11----- Coding stand. : Standard defined for the GSM-PLMNS ---0---- spare : 0 ----0000 location : user 90 -0010000 cause : Normal call clearing
_____[ 81 ]___[ 11:53:05,477 ]___[ DOWN ]____[ FACCH_F ]______________________________
06 0d 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
0d 00001101 MESSAGE TYPE : CHANNEL RELEASE
00 00000000 RR-Cause (reason of event) = Normal event
_____[ 82 ]___[ 11:53:05,578 ]___[ DOWN ]____[ SACCH ]______________________________
06 1d 10 00 00 00 00 00 00 00 00 00 00 c0 20 95 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1d 00011101 MESSAGE TYPE : SYSTEM INFORMATION TYPE 5
10 00------ Format Type : Bit Map 0 format --0----- Extension Indicator : The IE carries the complete BA ---1---- BCCH allocation sequence number indication 1
c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3920 --1----- BCCH alloc. RF chan.: 3095 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
_____[ 83 ]___[ 11:53:05,738 ]___[ UP ]____[ FACCH_F ]______________________________
06 15 98 15 00 d4 0b a6 09 e2 8a f8 00 00 00 00 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
15 00010101 MESSAGE TYPE : MEASUREMENT REPORT
98 1------- BA used : yes -0------ Discontinous Transmission was not used --011000 RXLEV-FULL-SERVING-CELL= (-110 + 24) dB
15 0------- spare : 0 -0------ MEAS-VALID : yes --010101 RXLEV-SUB-SERVING-CELL = (-110 + 21) dB 0------ spare : 0 -000--- RX-QUAL-FULL-SERVING-CELL = ~0,14% error bit ----000 RX-QUAL-SUB -SERVING-CELL = ~0,14% error bit 011 Number of neighbouring cell measurements = 3
010100 RXLEV-Neighbour-CELL 1 = (-110 + 20) dB 00001 BCCH-FREQ-NCELL 1 : 1 011101 Base station identity code of the 1'th neighbouring cell = 29
001100 RXLEV-Neighbour-CELL 2 = (-110 + 12) dB 00010 BCCH-FREQ-NCELL 2 : 2 011110 Base station identity code of the 2'th neighbouring cell= 30
001010 RXLEV-Neighbour-CELL 3 = (-110 + 10) dB 00101 BCCH-FREQ-NCELL 3 : 5 011111 Base station identity code of the 3'th neighbouring cell = 31
000000 RXLEV-Neighbour-CELL 4 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 4 : 0 000000 Base station identity code of the 4'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 5 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 5 : 0 000000 Base station identity code of the 5'th neighbouring cell = 0
000000 RXLEV-Neighbour-CELL 6 = (-110 + 0) dB 00000 BCCH-FREQ-NCELL 6 : 0 000000 Base station identity code of the 6'th neighbouring cellt = = 0
_____[ 84 ]___[ 11:53:06,398 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity aa 10101010 Cell identity value1: Hex-Wert verwendenb2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present 1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 85 ]___[ 11:53:06,629 ]___[ DOWN ]____[ BCCH ]______________________________
06 1c 62 f2 10 31 04 65 08 a5 00 00 01 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1c 00011100 MESSAGE TYPE : SYSTEM INFORMATION TYPE 4
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAI), ID of MSC (hex)04 00000100 Loc. area code (LAI), ID of BSC (hex)
: Cell Selection Parameters 65 011----- Cell Reselect Hyst. : 6 dB RXLEV hyst. For LA re-select ---00101 Max Tx power level : MS may use 5
08 0------- No Additional cells in SysInfo 7-8 -0------ New establishm.cause: not supported --001000 RXLEV ACCESS MIN permitted = -110+8dB
: RACH Control Parametersa5 10------ Max. of retransmissions --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestab.in cell: not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- Acc. ctrl class11-15: bit pattern,0 = access permitted, 1 = access forbidden ------00 Acc. ctrl class 8-9 : bit pattern,0 = access permitted, 1 = access forbidden00 00000000 Acc. ctrl class 0-7 : bit pattern,0 = access permitted, 1 = access forbidden
: SI4 Rest Octets : SI4 Rest Octets_O : Optional selection parameters 0 Selection Parameters = not present: End Optional selection parameters: Optional Power offset 0 Power Offset = not present: End Optional Power offset: GPRS Indicator 0 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm;: End GPRS Indicator: End SI4 Rest Octets_O : Break Indicator 1 High Additional parameters, "SI4 Rest Octets_S" are sent in SYSTEM INFORMATION TYPE 7 and 8: End SI4 Restoctet
_____[ 86 ]___[ 11:53:07,379 ]___[ DOWN ]____[ PCH ]______________________________
06 21 00 01 00 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
21 00100001 MESSAGE TYPE : PAGING REQUEST TYPE 1
00 ----00-- spare bits : 0 ------00 Page Mode : Normal paging --00---- Channel Needed : (first) Any Channel 00------ Channel Needed : (second) Any Channel
: Mobile Identity 101 00000001 length of Mob.ident.: 1 00 0000---- Identity Digit 1 : hex value = f, if TMSI/P-TMSI ----0--- No. of ID digits : even -----000 Type of identity : No Identity
_____[ 87 ]___[ 11:53:07,801 ]___[ DOWN ]____[ BCCH ]______________________________
06 19 00 00 00 02 00 10 00 00 00 00 00 00 00 00 00 00 a5 00 00 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
19 00011001 MESSAGE TYPE : SYSTEM INFORMATION TYPE 1
: Cell Channel Description 00 00------ Format Type : Bit Map 0 format --00---- 2 spare bits : 0
02 ------1- Cell Allocation : ARFCN 9810 ---1---- Cell Allocation : ARFCN 85
: RACH Control Parameters a5 10------ Max. of retransmiss : 4 --1001-- slots to spread TX : 12 ------0- The cell is barred : no -------1 Call reestabl.i.cell : not allowed
00 00000--- Acc. contr. cl. 11-15: Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl. -----0-- Emergency Call EC 10 : allowed ------00 Acc. contr. cl. 8-9 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
00 00000000 Acc. contr. cl. 0-7 : Bitmuster: 0 Zugr.erl.,1 Zugr.n.erl.
: NCH Position 0 no NCH Position 0101011 spare padding
_____[ 88 ]___[ 11:53:08,152 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 00 10 00 00 00 00 00 c0 20 95 00 00 08 a5 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1a 00011010 MESSAGHE TYPE : SYSTEM INFORMATION TYPE 2
00 --0----- Extension Indicator : The IE carries the complete BA ---0---- BCCH alloc. sequ.num: 0
10 ---1---- BCCH alloc. RF chan.: 85
c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3920 --1----- BCCH alloc. RF chan.: 3095 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
a5 10------ Max. of retransmiss.: 4 --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- acc ctrl class 11-15: 0/1 access permitted/forbidden ------00 acc ctrl class 8-9 : 0/1 access permitted/forbidden
00 00000000 acc ctrl class 0-7 : 0/1 access permitted/forbidden
_____[ 89 ]___[ 11:53:08,754 ]___[ DOWN ]____[ BCCH ]______________________________
06 00 f0 00 58 58 67 ca 10 80 51 80 ab 2b 2b 2b 2b 2b 2b 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
00 00000000 MESSAGE TYPE : SYSTEM INFORMATION TYPE 13
1------- SI 13 Restoctet : present -111---- BCCH_CHANGE_MARK : 7 ----0000 SI_CHANGE_FIELD : Update of unspecified SI messages
0 switch SI13_CHANGE_MARK and GPRS Mobile Allocation = not present
0 PBCCH not present in Cell 00000001 RAC (Routing Area Code) = 1 0 SPGC_CCCH_SUP : SPLIT_PG_CYCLE not supported on CCCH: Priority access 110 packet access is allowed for priority level 1 to 4;: Network Control Order 00 NETWORK_CONTR. ORDER: MS controlled cell re-selection, no measurement reporting.
: GPRS CELL OPTIONS IE
01 NMO Network Mode of Operation II : No PPCH available, no Gs If
011 T3168 : (3+1)x500 ms 000----- T3192 : 500msec ---011-- DRXTIMER_MAX ------0- ACCESS_BURST_TYPE : Use 8 bit access burst -------0 default format is four access bursts 1111 BS_CV_MAX : Countdown Value = 15 1 PAN description = present 001 PAN_DEC 010 PAN_INC 000 PAN_MAX : Max value for counter N3102= 5
: End GPRS Cell Options: GPRS Power Control Param structure
1000 ALPHA = 8 x 0,1
01000 T_AVG_W = 8 00000 T_AVG_T = 0 1 PC_MEAS_CHAN : Downlink Measurement shall be made on PDCH 0100 N_AVG_I : 2 exp (4/2): End GPRS Power Control Param structure
0110000 spare padding : 0
_____[ 90 ]___[ 11:53:08,953 ]___[ DOWN ]____[ BCCH ]______________________________
06 1a 00 00 00 00 00 10 00 00 00 00 00 c0 20 95 00 00 08 a5 00 00
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1a 00011010 MESSAGHE TYPE : SYSTEM INFORMATION TYPE 2
00 --0----- Extension Indicator : The IE carries the complete BA ---0---- BCCH alloc. sequ.num: 0
10 ---1---- BCCH alloc. RF chan.: 85c0 1------- BCCH alloc. RF chan.: 40 -1------ BCCH alloc. RF chan.: 3920 --1----- BCCH alloc. RF chan.: 3095 1------- BCCH alloc. RF chan.: 24 ---1---- BCCH alloc. RF chan.: 21 -----1-- BCCH alloc. RF chan.: 19 -------1 BCCH alloc. RF chan.: 17
08 ----1--- BCCH carrier with NCC = 3 is permitted for monitoring;
a5 10------ Max. of retransmiss.: 4 --1001-- 12 slots used to spread TX ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC 10: allowed 00000--- acc ctrl class 11-15: 0/1 access permitted/forbidden ------00 acc ctrl class 8-9 : 0/1 access permitted/forbidden
00 00000000 acc ctrl class 0-7 : 0/1 access permitted/forbidden
_____[ 91 ]___[ 11:53:09,215 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b aa b2 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity aa 10101010 Cell identity value1: Hex-Wert verwendenb2 10110010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present 1 High: GPRS indicator = present: RA COLOUR 000 Routing Area colour = 0: SI13 Position 0 SYSTEM INFORMATION TYPE 13 message is sent on BCCH Norm; 10101100 spare bits: End SI 3 Restoktett
_____[ 92 ]___[ 11:53:10,945 ]___[ DOWN ]____[ BCCH ]______________________________
06 1b cd 3a 62 f2 10 31 04 40 04 3c 55 65 08 a5 00 00 3c 2b 2b 2b
06 0------- direction from : originating site -000---- TransactionID : 0 ----0110 Protocol Discrim. : radio resource management messages
1b 00011011 MESSAGE TYPE : SYSTEM INFORMATION TYPE 3
: Cell Identity cd 11001101 Cell identity value1: Hex-Wert verwenden3a 00111010 Cell identity value2: Hex-Wert verwenden
: Location Area Identification 62 ----0010 Mobile CC digit 1 : 2 0110---- Mobile CC digit 2 : 6 f2 ----0010 Mobile CC digit 3 : 2
1111---- Mobile NC digit 3 : 15 10 ----0000 Mobile NC digit 1 : 0 0001---- Mobile NC digit 2 : 1
31 00110001 Loc. area code (LAC) = ID of MSC (hex) 04 00000100 Loc. area code (LAC) = ID of BSC (hex)
: Control Channel Description 40 0------- 1 spare bit : 0 -1------ MSs in the cell shall apply IMSI attach and detach procedure --000--- Number of blocks : 0 reserved for access grant -----000 1 basic physical channel used for CCCH not combined with SDCCHs
04 00000--- spare bits : 5 -----100 6 multi frames period for transmission PAGING REQUEST messages to the same paging subgroup
3c 00111100 T3212 TimeOut value : 60 deci hours
: Cell Options BCCH, 55 0------- 1 spare bit : 0 -1------ PWRC Power control indicator is set --01---- MSs shall use uplink discontinous transmission ----0101 Radio Link Timeout : 24
: Cell Selection Parameters; 65 011----- Cell Resel. Hyster. : 6 dB RXLEV hysteresis for level average (LA) re-selection ---00101 Max Tx power level : Mobile may use 5
08 0------- Addition. Reselect Param ind: in SI4 rest octets, i.p., and SI7 and SI8 rest octets, ... -0------ New establishment cause is not supported --001000 RXLEV ACCESS MIN : -110 +8 db permitted
: RACH Control Parameters a5 10------ Max. of retransm. : 4 --1001-- used to spread TX : 12 slots ------0- The cell is barred : no -------1 Call reestablishment in cell is not allowed
00 -----0-- Emergency Call EC10 : allowed 00000--- Acc.contr.cl. 11-15 : 0/1 access permitted/forbidden ------00 Acc.contr.cl. 8-9 : 0/1 access permitted/forbidden
00 00000000 Acc.contr.cl. 0-7 : 0/1 access permitted/forbidden
: SI 3 Restoktett 0 Selection Parameters not present 0 Power Offset not present 1 System Information 2ter Indicator not present 1 Early Classmark Sending Control present 1 Scheduling if and where not present