zigbee technology

46
ZigBee Technology Seminar Report ‘09 1. INTRODUCTION 1.1 Evolution of Low-Rate Wireless Personal Area Network (LR-WPAN) Standardization The cellular network was a natural extension of the wired telephony network that became persistent during the mid-20th century. As the need for mobility and the cost of laying new wires increased, the motivation for a personal connection independent of location to that network also increased. Coverage of large area is provided through (1-2km) cells that cooperate with their neighbours to create a seemingly seamless network. Examples of standards are GSM, IS-136, IS-95. Cellular standards basically aimed at facilitating voice communications throughout a metropolitan area. During the mid-1980s, it turned out that an even smaller coverage area is needed for higher user densities and the emergent data traffic. The IEEE 802.11 working group for Wireless Local Area Network (WLAN) is formed, to create a wireless local area network standard. Whereas IEEE 802.11 was concerned with features such as Ethernet matching speed, long range(100m), Department of EEE School of Engineering,CUSAT -1-

Upload: minigun

Post on 15-Nov-2014

27 views

Category:

Documents


3 download

DESCRIPTION

ZigBee is the wireless networking technologybase on the IEEE 802.15.4 standard.this document covers all the portion of the ZigBee technology....hope u like it....

TRANSCRIPT

Page 1: Zigbee technology

ZigBee Technology Seminar Report ‘09

1. INTRODUCTION

1.1 Evolution of Low-Rate

Wireless Personal Area

Network (LR-WPAN)

StandardizationThe cellular network was a natural extension of the wired telephony network that became persistent during the mid-20th century. As the need for mobility and the cost of laying new wires increased, the motivation for a personal connection independent of location to that network also increased. Coverage of large area is provided through (1-2km) cells that cooperate with their neighbours to create a seemingly seamless network. Examples of standards are GSM, IS-136, IS-95. Cellular standards basically aimed at facilitating voice communications throughout a metropolitan area. During the mid-1980s, it turned out that an even smaller coverage area is needed for higher user densities and the emergent data traffic.

The IEEE 802.11 working group for Wireless Local Area Network (WLAN) is formed, to create a wireless local area network standard. Whereas IEEE 802.11 was concerned with features such as Ethernet matching speed, long range(100m), complexity to handle seamless roaming, message forwarding, and data throughput of 2-11Mbps.

Wireless personal area networks (WPANs) are used to convey information over relatively short distances. WPANs are focused on a space around a person or object that typically extends up to 10m in all directions. The focus of WPANs is low-cost, low power, short range and very small size.

The IEEE 802.15 working group is formed to create WPAN standard.This group has currently defined three classes of WPANs that are differentiated by data rate, battery drain and quality of service (QoS).

Department of EEE School of Engineering,CUSAT-1-

Page 2: Zigbee technology

ZigBee Technology Seminar Report ‘09

The high data rate WPAN (IEEE 802.15.3) is suitable for multi-media applications that require very high QoS.

Medium rate WPANs (IEEE 802.15.1/Bluetooth) will handle a variety of tasks ranging from cell phones to PDA communications and have QoS suitable for voice communications.

The low rate WPANs (IEEE 802.15.4/LR-WPAN) is intended to serve a set of industrial, residential and medical applications with very low power consumption, with relaxed needs for data rate and QoS. The low data rate enables the LR-WPAN to consume very little power. This feature allows small, power-efficient, inexpensive solutions to be implemented for a wide range of devices.

1.2 Zigbee and IEEE 802.15.4The IEEE 802.15.4 standard is a simple packet data protocol for lightweight wireless networks and specifies the Physical (PHY) and Medium Access Control (MAC) layers for Multiple Radio Frequency (RF) bands, including 868 MHz, 915 MHz, and 2.4 GHz.

The IEEE 802.15.4 standard is designed to provide reliable data transmission of modest amounts of data up to 100 meters or more while consuming very little power. IEEE 802.15.4 is typically less than 32 kb in size, featuring a 64-bit address space, source and destination addressing, error detection, and advanced power management. ZigBee technology takes full advantage of the IEEE 802.15.4 standard and extends the capabilities of this new radio standard by defining a flexible and secure network layer that supports a variety of architectures to provide highly reliable wireless communications in harsh or dynamic RF environments.

ZigBee technology also offers simplicity and a cost-effective approach to building, construction and remodelling with wireless technology. ZigBee is all set to provide the consumers with ultimate flexibility, mobility, and ease of use by building wireless intelligence and capabilities into every day devices.

Department of EEE School of Engineering,CUSAT-2-

Page 3: Zigbee technology

ZigBee Technology Seminar Report ‘09 ZigBee is expected to provide low cost and low power connectivity for equipment that needs battery life as long as several months to several years but does not require data transfer rates as high as those enabled by Bluetooth. This kind of network eliminates use of physical Ethernet cables. The devices could include telephones, hand-held digital assistants, sensors and controls located within a few meters of each other.

Thus, ZigBee technology is a low data rate, low power consumption, low cost; wireless networking protocol targeted towards automation and remote control applications.

1.2.1 ZigBee Alliance

The ZigBee Alliance is an association of companies working together to enable reliable, cost-effective, low-power, wirelessly networked, monitoring and control products based on an open global standard. The goal of the ZigBee Alliance is to provide the consumer with ultimate flexibility, mobility, and ease of use by building wireless intelligence and capabilities into every day devices. ZigBee technology will be embedded in a wide range of products and applications across consumer, commercial, industrial and government markets worldwide. For the first time, companies will have a standards-based wireless platform optimized for the unique needs of remote monitoring and control applications, including simplicity, reliability, low-cost and low-power.

1.2.2 Why is it called Zigbee?It has been suggested that the name evokes the haphazard paths that bees follow as they harvest pollen, similar to the way packets would move through a mesh network

Using communication system, whereby the bee dances in a zig-zag pattern, worker bee is able to share information such as the location, distance,And direction of a newly discovered food source to her fellow colony members. Instinctively implementing the ZigBee Principle, bees around the

Department of EEE School of Engineering,CUSAT-3-

Page 4: Zigbee technology

ZigBee Technology Seminar Report ‘09world actively sustain productive itchiness and promote future generations of Colony members.

2. IEEE 802.15.4 WPAN

2.1 General descriptionA LR-WPAN is a simple, low-cost communication network that allows wireless connectivity in applications with limited power and relaxed throughput requirements. The main objectives of an LR-WPAN are ease of installation, reliable data transfer, short-range operation, extremely low cost, and a reasonable battery life, while maintaining a simple and flexible protocol.

The three license-free frequencies of the IEEE 802.15.4 standard include sixteen channels at 2.4 GHz, ten channels at 915 MHz, and one channel at 868 MHz, to support global or regional deployment. The maximum data rates for each band are 250 kbps, 40 kbps and 20 kbps, respectively. Theair interface is direct sequence spread spectrum (DSSS) using binary phase shift keying (BPSK) for 868 MHz and 915 MHz and offset-quadrature phase shift keying (OQPSK) for 2.4 GHz.

Other features of the IEEE 802.15.4 PHY include receiver energy detection, link quality indication and clear channel assessment. Both contention-based and contention-free channel access methods are supported. Maximum packet size is 128 bytes, including a variable payload of up to 104 bytes. IEEE 802.15.4 employs 64-bit IEEE and 16-bit short addresses, which supports over 65,000 nodes per network.

The IEEE 802.15.4 MAC also enables network association and disassociation, has an optional super frame structure with beacons for time synchronization, and a guaranteed time slot (GTS) mechanism for high priority communications. The access method is carrier sense multiple access with collision avoidance (CSMA-CA). Network routing schemes are designed to ensure power conservation, and low latency through

Department of EEE School of Engineering,CUSAT-4-

Page 5: Zigbee technology

ZigBee Technology Seminar Report ‘09guaranteed time slots. A unique feature of ZigBee network layer is communication redundancy eliminating “single point of failure” in mesh networks.

IEEE and ZigBee Alliance have been working closely to specify the entire protocol stack. IEEE 802.15.4 focuses on the specification of the lower two layers of the protocol (physical and data link layer). On the other hand,

Department of EEE School of Engineering,CUSAT-5-

Page 6: Zigbee technology

ZigBee Technology Seminar Report ‘09

ZigBee Alliance aims to provide the upper layers of the protocol stack (from network to the application layer) for interoperable data networking, security services and a range of wireless home and building control solutions.

2.2 Zigbee characteristicsThe focus of network applications under the IEEE 802.15.4 / ZigBee standard include the features of low power consumption, needed for only two major modes (Tx/Rx or Sleep), high density of nodes per network, low costs and simple implementation.

These features are enabled by the following characteristics

2.4GHz and 868/915 MHz dual PHY modes. This represents three license-free bands: 2.4-2.4835 GHz, 868-870

MHz and 902-928 MHz The number of channels allotted to each frequency band is fixed at 16 channels in the 2.45 GHz band, 10 channels in the 915 MHz band, and 1 channel in the 868 MHz band

Maximum data rates allowed for each of these frequency bands are fixed as 250 kbps @2.4 GHz, 40 kbps @ 915 MHz, and 20 kbps @868 MHz

Allocated 16 bit short or 64 bit extended addresses. Allocation of guaranteed time slots (GTSs) Carrier sense multiple access with collision avoidance (CSMA-CA)

channel access Yields high throughput and low latency for low duty cycle devices like sensors and controls.

Fully “hand-shake” acknowledged protocol for transfer reliability. Low power consumption with battery life ranging from months to

years. Energy detection (ED). Link quality indication (LQI). Multiple topologies : star, peer-to-peer, mesh topologies

Department of EEE School of Engineering,CUSAT-6-

Page 7: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.3 Device TypesZigBee devices are required to conform to the IEEE 802.15.4-2003 Low-Rate Wireless Personal Area Network (WPAN) standard.

ZigBee wireless devices are expected to transmit 10-75 meters, depending on the RF environment and the power output consumption required for a given application, and will operate in the unlicensed RF worldwide (2.4GHz global, 915MHz Americas or 868 MHz Europe). The data rate is 250kbps at 2.4GHz, 40kbps at 915MHz and 20kbps at 868MHz.

There are three different ZigBee device types that operate on these layers in any self-organizing application network. These devices have 64-bit IEEE addresses, with option to enable shorter addresses to reduce packet size, and work in either of two addressing modes – star and peer-to-peer.

The ZigBee (PAN) coordinator node: The most capable device, the coordinator forms the root of the network tree and might bridge to other networks. It is able to store information about the network.There is one, and only one, ZigBee coordinator in each network to act as the router to other network. It also acts as the repository for security keys.

The Full Function Device (FFD): The FFD is an intermediary router transmitting data from other devices. It needs lesser memory than the ZigBee coordinator node, and entails lesser manufacturing costs. It can operate in all topologies and can act as a coordinator.

The Reduced Function Device (RFD) : This device is just capable of talking in the network; it cannot relay data from other devices. Requiring even less memory, (no flash, very little ROM and RAM), an RFD will thus be cheaper than an FFD. This device talks only to a network coordinator and can be implemented very simply in star topology.

An FFD can talk to RFDs or other FFDs, while an RFD can talk only to an FFD. An RFD is intended for applications that are extremely simple, such as a light switch or a passive infrared sensor; they do not have the need to send large amounts of data and may only associate with a single FFD at a

Department of EEE School of Engineering,CUSAT-7-

Page 8: Zigbee technology

ZigBee Technology Seminar Report ‘09time. Consequently, the RFD can be implemented using minimal resources and memory capacity.

Department of EEE School of Engineering,CUSAT-8-

Page 9: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.4 Network TopologiesFigure 2.1 shows 3 types of topologies that ZigBee supports: star topology, peer-to-peer topology and cluster tree.

2.4.1 Star TopologyIn the star topology, the communication is established between devices and a single central controller, called the PAN coordinator. The PAN coordinator may be mains powered while the devices will most likely be battery powered. Applications that benefit from this topology include home automation, personal computer (PC) peripherals, toys and games. After an FFD is activated for the first time, it may establish its own network and become the PAN coordinator. Each start network chooses a PAN identifier, which is not currently used by any other network within the radio sphere of influence. This allows each star network to operate independently.

Department of EEE School of Engineering,CUSAT-9-

Page 10: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.4.2 Peer-to-peer TopologyIn peer-to-peer topology, there is also one PAN coordinator. In contrast to star topology, any device can communicate with any other device as long as they are in range of one another. A peer-to-peer network can be ad hoc, self-organizing and self-healing. Applications such as industrial control and monitoring, wireless sensor networks, asset and inventory tracking would benefit from such a topology. It also allows multiple hops to route messages from any device to any other device in the network. It can provide reliability by multipath routing.

Department of EEE School of Engineering,CUSAT-10-

Page 11: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.4.3 Cluster-tree TopologyCluster-tree network is a special case of a peer-to-peer network in which most devices are FFDs and an RFD may connect to a cluster-tree network as a leave node at the end of a branch. Any of the FFD can act as a coordinator and provide synchronization services to other devices and coordinators.Only one of these coordinators however is the PAN coordinator. The PAN coordinator forms the first cluster by establishing itself as the cluster head (CLH) with a cluster identifier (CID) of zero, choosing an unused PAN identifier, and broadcasting beacon frames to neighbouring devices. A candidate device receiving a beacon frame may request to join the network at the CLH. If the PAN coordinator permits the device to join, it will add this new device as a child device in its neighbour list. The newly joined device will add the CLH as its parent in its neighbour list and begin transmitting periodic beacons such that other candidate devices may then join the network at that device. Once application or network requirements are met, the PAN coordinator may instruct a device to become the CLH of a new cluster adjacent to the first one. The advantage of this clustered structure is the increased coverage area at the cost of increased message latency.

Department of EEE School of Engineering,CUSAT-11-

Page 12: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.5 ArchitectureThe LR-WPAN architecture is defined in terms of a number of blocks in order to simplify the standard. These blocks are called layers. Each layer is responsible for one part of the standard and offers services to the higher layers. The layout of the blocks is based on the open systems interconnection (OSI) seven-layer model. The interfaces between the layers serve to define the logical links between layers. The LR-WPAN architecture can be implemented either as embedded devices or as devices requiring the support of an external device such as a PC.

An LR-WPAN device comprises a PHY, which contains the radio frequency (RF) transceiver along with its low-level control mechanism, and a MAC sub layer that provides access to the physical channel for all types of transfer

Department of EEE School of Engineering,CUSAT-12-

802.15.4 / ZigBee Architecture

802.15.4 MAC

ZigBee Application layer

ZigBee Network layer

802.15.4 PHY 2.4 Ghz

802.15.4 MAC

802.15.4 PHY 868/915 Mhz

IEEE

Page 13: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.5.1 Network and Application Support layer :

The network layer permits growth of network sans high power transmitters. This layer can handle huge numbers of nodes.This level in the ZigBee architecture includes

The ZigBee Device Object (ZDO) User-Defined Application Profile(s) The Application Support (APS) Sub-layer.

The APS sub-layer's responsibilities include maintenance of tables that enable matching between two devices and communication among them, and also discovery, the aspect that identifies other devices that operate in the operating space of any device.

The responsibility of determining the nature of the device (Coordinator / FFD or RFD) in the network, commencing and replying to binding requests and ensuring a secure relationship between devices rests with the ZDO (Zigbee Define Object). The user-defined application refers to the end device that conforms to the ZigBee Standard.

Department of EEE School of Engineering,CUSAT-13-

ZigbeeAlliance

Page 14: Zigbee technology

ZigBee Technology Seminar Report ‘09

2.5.2 Physical (PHY) layer:The PHY service enables the transmission and reception of PHY protocol data units (PPDU) across the physical radio channel.

The features of the IEEE 802.15.4 PHY physical layer are Activation and deactivation of the radio transceiver, energy detection (ED), Link quality indication (LQI), channel selection, clear channel assessment (CCA) and transmitting as well as receiving packets across the physical medium.

2.5.3 Media access control (MAC) layer:

The MAC service enables the transmission and reception of MAC protocol data units (MPDU) across the PHY data service.

The features of MAC sub layer are beacon management, channel access, GTS management, frame validation, acknowledged frame delivery, association and disassociation.

3. IEEE 802.15.4 PHYThe PHY provides an interface between the MAC sub layer and the physical radio channel, via the RF firmware and RF hardware.

The PHY conceptually includes a management entity called the PLME.This entity provides the layer management service interfaces through which layer management functions may be invoked. The PLME is also responsible for maintaining a database of managed objects pertaining to the PHY. This database is referred to as the PHY PAN Information base (PIB).

Figure 3.1 depicts the components and interfaces of the PHY.

Department of EEE School of Engineering,CUSAT-14-

PD_SAP PLME_SAP

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

RF_SAP

PHYLIB

PHY LAYERPLME

Figure 3.1 PHY LAYER REFERENCE MODEL

Page 15: Zigbee technology

ZigBee Technology Seminar Report ‘09

The PHY provides two services, accessed through two SAPs:The PHY data service accessed through the PHY Data SAP (PD-SAP). The PHY data service enables the transmission and reception of PHY protocol data units (PPDUs) across the physical radio channel.

The PHY management service, accessed through the PLME’s SAP (PLMESAP). The features of the PHY are activation and deactivation of the radio transceiver, energy detection(ED), link quality indication (LQI), channel selection, clear channel assessment (CCA) and transmitting as well as receiving packets across the physical medium.

The standard offers two PHY options based on the frequency band. Both are based on direct sequence spread spectrum (DSSS). The data rate is 250kbps at 2.4GHz, 40kbps at 915MHz and 20kbps at 868MHz. The higher data rate at 2.4GHz is attributed to a higher-order modulation scheme. Lower frequency provides longer range due to lower propagation losses. Low rate can be translated into better sensitivity and larger coverage area. Higher rate means higher throughput, lower latency or lower duty cycle. This information is summarized in Figure 3.2.

PHY(MHz)

FrequencyBand(MHz)

Spreading Parameters Data Parameters

Chiprate(kchip/s)

ModulationBit rate(kb/s)

Symbol rate(ksymbol/s)

Symbols

868/915

868-868.6 300 BPSK 20 20 Binary

902-928 600 BPSK 40 40 Binary

2450 2400-2483.5 2000 O-QPSK 250 62.5 16-ary

Department of EEE School of Engineering,CUSAT-15-

Figure 3.2 Frequency and Data Rates Bands

Page 16: Zigbee technology

ZigBee Technology Seminar Report ‘09

Orthogonal

There is a single channel between 868 and 868.6MHz, 10 channels between 902.0 and 928.0MHz, and 16 channels between 2.4 and 2.4835GHz as shown in Figure 3.3. Several channels in different frequency bands enables the ability to relocate within spectrum. The standard also allows dynamicChannel selection, a scan function that steps through a list of supported channels in search of beacon, receiver energy detection, link quality indication, channel switching.

Figure 3.3 Operating Frequency Bands

Department of EEE School of Engineering,CUSAT-16-

Page 17: Zigbee technology

ZigBee Technology Seminar Report ‘09

3.1 Receiver Energy Detection

(ED)The receiver energy detection (ED) measurement is intended for use by a network layer as part of channel selection algorithm. It is an estimate of the received signal power within the bandwidth of an IEEE 802.15.4 channel. No attempt is made to identify or decode signals on the channel. The ED time should be equal to 8 symbol periods.

The ED result shall be reported as an 8-bit integer ranging from 0x00 to 0xff. The minimum ED value (0) shall indicate received power less than 10dB above the specified receiver sensitivity. The range of received power spanned by the ED values shall be at least 40dB. Within this range, the mapping from the received power in decibels to ED values shall be linear with an accuracy of + or − 6dB.

3.2 Link Quality Indication (LQI)Upon reception of a packet, the PHY sends the PSDU length, PSDU itself and link quality (LQ) in the PD-DATA. Indication primitive. The LQI measurement is a characterization of the strength and/or quality of a received packet. The measurement may be implemented using receiver ED, a signal-to-noise estimation or a combination of these methods. The use of LQI result is up to the network or application layers.

The LQI result should be reported as an integer ranging from 0x00 to 0xff. The minimum and maximum LQI values should be associated with the lowest and highest quality IEEE 802.15.4 signals detectable by the receiver and LQ values should be uniformly distributed between these two limits.

3.3 Clear Channel Assessment (CCA)The clear channel assessment (CCA) is performed according to at least one of the following three methods:

Energy above threshold. CCA shall report a busy medium upon detecting any energy above the ED threshold.

Department of EEE School of Engineering,CUSAT-17-

Page 18: Zigbee technology

ZigBee Technology Seminar Report ‘09

Carrier sense only. CCA shall report a busy medium only upon the detection of a signal with the modulation and spreading characteristics of IEEE 802.15.4. This signal may be above or below the ED threshold.

Carrier sense with energy above threshold. CCA shall report a busy medium only upon the detection of a signal with the modulation and spreading characteristics of IEEE 802.15.4 with energy above the ED threshold.

3.4 PPDU FormatThe PPDU packet structure is illustrated in Figure 3.4. Each PPDU packet consists of the following basic components:

SHR, which allows a receiving device to synchronize and lock into the bit stream

PHR, which contains frame length information A variable length payload, which carries the MAC sub layer frame.

Department of EEE School of Engineering,CUSAT-18-

Figure 3.4 Format of the PPDU

Page 19: Zigbee technology

ZigBee Technology Seminar Report ‘09

4. IEEE 802.15.4 MAC

Figure 4.1 depicts the components and interfaces of the MAC sub layer.

The MAC sub layer provides an interface between the SSCS and the PHY. The MAC sub layer conceptually includes a management entity called the MLME. This entity provides the service interfaces through which layer management functions may be invoked. The MLME is also responsible for maintaining a database of managed objects pertaining to the MAC sub layer. This database is referred to as the MAC sub layer PIB.

The MAC sub layer provides two services:

Department of EEE School of Engineering,CUSAT-19-

Figure 4.1 MAC SUBLAYER REFERENCE MODEL

MCPS_SAP MLME_SAP

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

802.15.4 PHY2.4 Ghz

PLME_SAP

MACLIB

MAC LAYER

MLME

PD_SAP

Page 20: Zigbee technology

ZigBee Technology Seminar Report ‘09The MAC data service and The MAC management service interfacing to the MAC sub layer management entity (MLME) service access point (SAP) (MLMESAP).

The MAC data service enables the transmission and reception of MAC protocol data units (MPDU) across the PHY data service.

The features of MAC sub layer are beacon management, channel access, GTS management, frame validation, acknowledged frame delivery, association and disassociation.

4.1 Superframe StructureLR-WPAN allows the optional use of a super frame structure. The format of the super frame is defined by the coordinator. The super frame is bounded by network beacons and is divided into 16 equally sized slots. The beacon frame is sent in the first slot of each super frame. If a coordinator does not want to use the super frame structure, it may turn off the beacon transmissions. The beacons are used to synchronize the attached devices, to identify the PAN and to describe the structure of super frames.The super frame can have an active and an inactive portion. During the inactive portion, the coordinator shall not interact with its PAN and may enter a low-power mode. The active portion portion consists of contention access period (CAP) and contention free period (CFP). Any device wishing to communicate during the CAP shall compete with other devices using a slotted CSMACA mechanism. On the other hand, the CFP contains guaranteed time slots (GTSs). The GTSs always appear at the end of the active super frame starting at a slot boundary immediately following the CAP. The PAN coordinator may allocate up to seven of these GTSs and a GTS can occupy more than one slot period.

Department of EEE School of Engineering,CUSAT-20-

Page 21: Zigbee technology

ZigBee Technology Seminar Report ‘09

4.2 CSMA-CA AlgorithmIf super frame structure is used in the PAN, then slotted CSMA-CA shall be used. If beacons are not being used in the PAN or a beacon cannot be located in a beacon-enabled network, unslotted CSMA-CA algorithm is used. In both cases, the algorithm is implemented using units of time calledBack off periods, which is equal to a Unit Back off Period symbols.

In slotted CSMA-CA channel access mechanism, the back off period boundaries of every device in the PAN are aligned with the super frame slot boundaries of the PAN coordinator. In slotted CSMA-CA, each time a device wishes to transmit data frames during the CAP, it shall locate the Boundary of the next back off period. In unslotted CSMA-CA, the back off periods of one device do not need to be synchronized to the back off periods of another device.

Department of EEE School of Engineering,CUSAT-21-

Figure 4.2 SUPER FRAME STRUCTURE

Page 22: Zigbee technology

ZigBee Technology Seminar Report ‘09

4.3 Traffic TypesZigBee/IEEE 802.15.4 addresses three typical traffic types. IEEE 802.15.4 MAC can accommodate all the types.

Data is periodic. The application dictates the rate, and the sensor activates checks for data and deactivates.

Data is intermittent. The application, or other stimulus, determines the rate, as in the case of say smoke detectors. The device needs to connect to the network only when communication is necessitated. This type enables optimum saving on energy.

Data is repetitive, and the rate is fixed a priori. Depending on allotted time slots, called GTS (guaranteed time slot), devices operate for fixed durations

ZigBee employs either of two modes, beacon or non-beacon to enable the to-and-fro data traffic. Beacon mode is used when the coordinator runs on batteries and thus offers maximum power savings, whereas the non-beacon mode finds favour when the coordinator is mains-powered.

4.4 Data Transfer modelThree types of data transfer transactions exist: from a coordinator to a device, from a device to a coordinator and between two peer devices. The mechanism for each of these transfers depends on whether the network supports the transmission of beacons.

The non-beacon mode will be included in a system where devices are ‘asleep' nearly always, as in smoke detectors and burglar alarms. The devices wake up and confirm their continued presence in the network at random intervals.

When a device wishes to transfer data in a no beacon-enabled network, it simply transmits its data frame, using the unslotted CSMA-CA, to the coordinator. On detection of activity, the sensors ‘spring to attention', as it were, and transmit to the ever-waiting coordinator's receiver (since it is

Department of EEE School of Engineering,CUSAT-22-

Page 23: Zigbee technology

ZigBee Technology Seminar Report ‘09mains-powered). There is also an optional acknowledgement at the end as shown in Figure 4.3.

In the beacon mode, a device watches out for the coordinator's beacon that gets transmitted at periodically, locks on and looks for messages addressed to it. If message transmission is complete, the coordinator dictates a schedule for the next beacon so that the device ‘goes to sleep'; in fact, the coordinator itself switches to sleep mode.

While using the beacon mode, all the devices in a mesh network know when to communicate with each other. In this mode, necessarily, the timing circuits have to be quite accurate, or wake up sooner to be sure not to miss the beacon. This in turn means an increase in power consumption by the coordinator's receiver, entailing an optimal increase in costs.

When a device wishes to transfer data to a coordinator in a beacon-enabled network, it first listens for the network beacon. When the beacon is found, it synchronizes to the super frame structure. At the right time, it transmits its data frame, using slotted CSMA-CA, to the coordinator. There is an optional acknowledgement at the end as shown in Figure 4.4.

Department of EEE School of Engineering,CUSAT-23-

Page 24: Zigbee technology

ZigBee Technology Seminar Report ‘09

The applications transfers are completely controlled by the devices on a PAN rather than by the coordinator. This provides the energy-conservation feature of the ZigBee network.

When a coordinator wishes to transfer data to a device in a beacon-enabled network, it indicates in the network beacon that the data message is pending. The device periodically listens to the network beacon, and if a message is pending, transmits a MAC command requesting this data, using slotted CSMA-CA. The coordinator optionally acknowledges the successful transmission of this packet. The pending data frame is then sent using slotted CSMA-CA. The device acknowledged the successful reception of the data by transmitting an acknowledgement frame. Upon receiving the acknowledgement, the message is removed from the list of pending messages in the beacon as shown in Figure 4.5.

Department of EEE School of Engineering,CUSAT-24-

Page 25: Zigbee technology

ZigBee Technology Seminar Report ‘09

When a coordinator wishes to transfer data to a device in a nonbeacon-enabled network, it stores the data for the appropriate device to make contact and request data. A device may make contact by transmitting a MAC command requesting the data, using unslotted CSMA-CA, to its coordinator at an application-defined rate. The coordinator acknowledges this packet. If data are pending, the coordinator transmits the data frame using unslotted CSMA-CA. If data are not pending, the coordinator transmits a data frame with a zero-length payload to indicate that no data were pending.

The device acknowledges this packet as shown in Figure 4.6.

Department of EEE School of Engineering,CUSAT-25-

Page 26: Zigbee technology

ZigBee Technology Seminar Report ‘09

In a peer-to-peer network, every device can communicate with any other device in its transmission radius. There are two options for this. In the first case, the node will listen constantly and transmit its data using unslotted CSMA-CA. In the second case, the nodes synchronize with each Other so that they can save power. .

Department of EEE School of Engineering,CUSAT-26-

Page 27: Zigbee technology

ZigBee Technology Seminar Report ‘09

5. ZigBee Routing Layer

5.1 AODV : Ad hoc On Demand

Distance VectorAODV is a pure on-demand route acquisition algorithm: nodes that do not lie on active paths neither maintain any routing information nor participate in any periodic routing table exchanges. Further, a node does not have to discover and maintain a route to another node until the two needs to communicate, unless the former node is offering services as an intermediate forwarding station to maintain connectivity between two other nodes. The primary objectives of the algorithm are to broadcast discovery packets only when necessary, to distinguish between local connectivity management and general topology maintenance and to disseminate information aboutchanges in local connectivity to those neighbouring mobile nodes that are likely to need the information.When a source node needs to communicate with another node for which it has no routing information in its table, the Path Discovery process is initiated. Every node maintains two separate counters: sequence number and broadcast id. The source node initiates path discovery by broadcastinga route request (RREQ) packet to its neighbours, which includes source addr, source sequence number, broadcast id, dest addr, dest sequencenumber, hop cnt. (Source sequence number is for maintaining freshness information about the reverse route whereas the destination sequence number is for maintaining freshness of the route to the destination before it can be accepted by the source.)The pair source addr, broadcast id uniquely identifies a RREQ, where broadcast id is incremented whenever the source issues a new RREQ. When an intermediate node receives a RREQ, if it has already received a RREQ with the same broadcast id and source address, it drops the redundant RREQ and does not rebroadcast it. Otherwise, it rebroadcasts it to its own neighbours after increasing hop cnt. Each node keeps the following information: destination IP address, source IP address, broadcast id, expiration time for reverse path route entry and source node’s sequence number.

Department of EEE School of Engineering,CUSAT-27-

Page 28: Zigbee technology

ZigBee Technology Seminar Report ‘09As the RREQ travels from a source to destinations, it automatically sets up the reverse path from all nodes back to the source. To set up a reverse path, a node records the address of the neighbour from which it received the first copy of RREQ.

These reverse path route entries are maintained for at least enough time for the RREQ to traverse the network and produce a reply to the sender.When the RREQ arrives at a node , possibly the destination itself that possesses a current route to the destination, the receiving node first checks that the RREQ was received over a bi-directional link. If this node is not destination but has route to the destination, it determines whether the routeis current by comparing the destination sequence number in its own route entry to the destination sequence number in the RREQ. If RREQ’s sequence number for the destination is greater than that recorded by the intermediate node, the intermediate node must not use this route to respond to the RREQ, instead rebroadcasts the RREQ.

If the route has a destination sequence number that is greater than that contained in the RREQ or equal to that contained in the RREQ but a smaller hop count, it can unicasts a route reply packet (RREP) back to its neighbour from which it received the RREQ. A RREP contains the following information: source addr, dest addr, dest sequence number, hop cnt and lifetime. As the RREP travels back to the source, each node along the path sets up a forward pointer to the node from which the RREP came, updates its timeout information for route entries to the source and destination, and records the latest destination sequence number for the requested destination.Nodes that are along the path determined by the RREP will timeout after route request expiration timer and will delete the reverse pointers since they are not on the path from source to destination as shown in Figure 5.1. The value of this timeout time depends on the size of the ad hoc network.

Department of EEE School of Engineering,CUSAT-28-

Page 29: Zigbee technology

ZigBee Technology Seminar Report ‘09

Department of EEE School of Engineering,CUSAT-29-

Page 30: Zigbee technology

ZigBee Technology Seminar Report ‘09

6. SUMMARY

6.1 Technology Comparisons

Department of EEE School of Engineering,CUSAT-30-

Page 31: Zigbee technology

ZigBee Technology Seminar Report ‘09

6.2 ZigBee Applications

The Zigbee Alliance targets applications "across consumer, commercial, industrial and government markets worldwide". Unwired applications are highly sought after in many networks that are characterized by numerous nodes consuming minimum power and enjoying long battery lives.

ZigBee technology is designed to best suit these applications, for the reason that it enables reduced costs of development, very fast market adoption, and rapid ROI.

With ZigBee designed to enable two-way communications, not only will the consumer be able to monitor and keep track of domestic utilities usage, but also feed it to a computer system for data analysis. A recent analyst report issued by West Technology Research Solutions estimates that by the year 2008, "annual shipments for ZigBee chipsets into the home automation segment alone will exceed 339 million units," and will show up in "light switches, fire and smoke detectors, thermostats, appliances in the kitchen, video and audio remote controls, landscaping, and security systems."

Futurists are sure to hold ZigBee up and say, "See, I told you so". The ZigBee Alliance is nearly 300 strong and growing, with more OEM's signing up. This means that more and more products and even later, all devices and their controls will be based on this standard. Since Wireless personal Area Networking applies not only to household devices, but also to individualized office automation applications, ZigBee is here to stay. It is more than likely the basis of future home-networking solutions.

The technology is designed to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10% of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2%. ZigBee is aimed at applications with low data rates and low power consumption.

Department of EEE School of Engineering,CUSAT-31-

Page 32: Zigbee technology

ZigBee Technology Seminar Report ‘09

Applications areas :

Enterprise systems : health care and patient monitoring, environmental , Monitoring and hazard detection.

Industrial systems : remote controlled machines such as in tracking wind turbines.

Military and government systems : asset tracking, personnel monitoring and surveillance.

Transportation systems : audio control and automation, security and access control.

Consumer products : cellular handsets , computer peripherals, remote controls and other portable devices.

Climate control : customize the temperatures of ac machines or thermostats as differently needed.

Home automation : turn on or off ovens, air conditioners, geysers, lights without any hassles only when needed. Also sprinkle water to plants in garden monitoring moisture content in soil.

Private Security : this also acts like a private security to monitor kids or aged even from office and alert in case of medical emergencies.

Department of EEE School of Engineering,CUSAT-32-

Page 33: Zigbee technology

ZigBee Technology Seminar Report ‘09

7. CONCLUSIONThe ZigBee Standard enables the broad-based deployment of reliable wireless networks with low complexity, low cost solutions and provides the ability for a product to run for years on inexpensive primary batteries (for a typical monitoring application). It is also, of course, capable of inexpensively supporting robust mesh networking technologies .ZigBee is all set to provide the consumers with ultimate flexibility, mobility, and ease of use by building wireless intelligence and capabilities into every day devices.

The mission of the ZigBee Working Group is to bring about the existence of a broad range of interoperable consumer devices by establishing open industry specifications for unlicensed, untethered peripheral, control and entertainment devices requiring the lowest cost and lowest power consumption communications between compliant devices anywhere in and around the home

Department of EEE School of Engineering,CUSAT-33-

Page 34: Zigbee technology

ZigBee Technology Seminar Report ‘09

8. References :

1. Understanding ZigBee , July 2009.

2. ZigBee “ wireless sensors and control networks” presented at Wireless

Congress 2008.

3. ZigBee “ the green wireless solution” published by Bob Heile,

Chairman, ZigBee alliance - December 1, 2008.

4. ZigBee Technical Overview , Tokyo Members Meeting Open House,

Tokyo, Japan - February 28, 2008.

Websites :-

1. http://www.technologyreview.com/articles/zigbee

2. http://www.zigbee.org

3. http://www.wisegeek.com

Department of EEE School of Engineering,CUSAT-34-