x b jxj series cycloid vertical grease grease oil bath type grease grease 32- 42 53- 117...

Download X B JXJ SERIES CYCLOID Vertical Grease Grease Oil bath type Grease Grease 32- 42 53- 117 Double-stage

Post on 05-Mar-2020

7 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • X B JXJ SERIES CYCLOID REDUCER

  • Characteristics

    1. 1/9-1/87 1/99-1/7569 1/2057-1/537399

    2. 90%

    3.

    4.

    5.

    6.

    7.

    1. Large ratio: the ratio is 1/9-1/87 at single reduce, 1/99-1/7569 at two stage reduce, 1/2057-1/537399 at three stage

    reduce; and also can have combo reduce per requirement.

    2. High efficiency: because of rolling mesh at gearing, the average efficiency is over 90%.

    3. Impact size, light weight: With planetary transmission, the input and output shafts are in in same axel, and unit is

    combined with motor in line.

    4. Less problem, long working life; the main gearing parts were made by bearing steel, the unit has good machanical

    property, by rolling attrition, it's less problem and long working life.

    5. Stable reliable turning, the unit is working by teeth meshing, thus it works stable reliable and low noisy.

    6. Ease disassembly, maintaining: With professional design, the unit is disassembly and maintain easily.

    7. High overloading, attacking and less inertia torque, the unit can be used in case of frequency starting and reversing.

    X B JXJ Series cycloid reducer

    JB/T2982-94

    This produce performs JB/T2982-94 national standards.

    Contrast different frame size

    Single-stage speed reducer contrast different frame size

    Series standard Type

    X X Tianjin B

    B

    B B Shanghai

    JXJ JXJ Jiangmen

    X2

    B0

    B12

    B10A

    JXJ0

    X3

    B1

    B15

    B11A

    JXJ1

    X4

    B2

    B18

    B12

    JXJ2

    X5

    B3

    B22

    B13

    JXJ3

    X6

    B4

    B27

    B14

    JXJ4

    X7

    B14A

    X8

    B5

    B33

    B15

    JXJ5

    X9

    B6

    B39

    B16

    JXJ6

    X10

    B7

    B45

    B17

    JXJ7

    X11

    B8

    B55

    B18

    JXJ8

    Double-stage speed reducer contrast different frame size

    Series standard Type

    X32

    B10

    B1512

    B110A

    JXJE0

    X42

    B21

    B1812

    B120A

    JXJE20

    X53

    B31

    B2215

    B131A

    JXJE31

    X63

    B41

    B2715

    B141A

    JXJE41

    X64

    B42

    B2718

    B142

    JXJE42

    X74

    B142A

    X84

    B52

    B3318

    B152

    JXJE52

    X95

    B63

    B3922

    B163

    JXJE63

    X106

    B74

    B4527

    B174

    JXJE74

    X117

    B85

    B5527

    B184A

    JXJE85

    X85

    B53

    B3322

    B153

    JXJE53

    Examole for type designation

    Table of allowable torque of cycloid speed reducer

    N.m Limited torque data

    N.m

    Type X2

    150

    X3

    250

    X4

    500

    X5

    1000

    X6

    2000

    X7

    2700

    X8

    4500

    X9

    7100

    X10

    12000

    X11

    20000

    L- W- X- Y- D- E- B- T

    N- Z-

    Letter sign:

    L-Upright, W-horizontal, X-micro cycloid, Y-motor flange, D-with motor, B-with explosion proof motor, T-Reduce motor,

    N-Brake motor, Z-DC motor

    X

    X X series micro cycloid reducer

    X W Y 5.5 5 23

    1 23

    E

    8

    9

    Reduction ratio

    1

    5

    5.5Kw

    X X series micro cycloid reducer

    X B L E D 63 289 1.5E

    2

    6# 3# Combination of motors 6# and 3#

    Monoblock type of normal motor

    B B series micro cycloid reducer

    B B series micro cycloid reducer

    B The Ministry of Chemical Industry

    The Ministry of Machinery

    X X Tianjin B

    B

    B B Shanghai

    JXJ JXJ Jiangmen

    B The Ministry of Chemical Industry

    The Ministry of Machinery

    Type designation of X series Illustration 1

    Type designation of B series Illustration 2

    Reduction ratio

    9

    8

    1.5Kw

    1 289

    1 Table 1

    2 Table 2

    3 Table 3

    Ever-Power Transmission Co., Ltd.

  • Procurement guide:

    Working coefficient table

    Table of purposes and load natures of speed reducers

    4 Table 4

    5 Table 5

    1.0

    1.2

    1.35

    Examples of selection

    Installation and usage

    Lubrication

    2- 4 5-x11 32- 42 53- 117

    6 Table 6

    5-x11

    Circulating Pump Circulating Pump

    (1) 1# 2L-2#

    (2) 90# 150#

    150# 220#

    1. 160%

    2.

    3. ( ) K

    4.

    1. It is designed based on a constant torque, therefore, during type selection, actual working torque shall be less than the rated torque,

    and maximum instantaneous load or start load shall be less than 160% of the rated load.

    2. If input spindle rotation speed is variable, it shall be in accordance with actual working conditions, if required power is constant, then the

    power shall satisfy the requirements of the lowest speed; if required torque is constant, then the power shall satisfy the requirements of

    the highest speed.

    3. In addition, consider working coefficients and power loss, therefore, the working torque (or power) shall be multiplied by working

    coefficient K.

    4. In conditions when overload is likely to occur, overload protection devices shall be installed, to avoid damages caused by the great

    transferred force from speed reducers and attached various power sources.

    Power source type

    Motor

    Working conditions

    3 / Of starts per hour 3

    8-10 / 8-10 hours/day

    24 / Continous 24 hours/day work

    Load nature

    ( ) Stable ( )

    0.8

    1.0

    1.2

    1.4

    1.5

    1.6

    ( ) Medium impact ( )

    ( ) Strong impact or inertia impact ( )

    Purposes

    Agitators

    Blower

    Air compressor

    Compressor

    ( ) Conveyer

    (Stable load)

    ( )

    Conveyer (Heavy load, non-uniform material feeding)

    Pure liquid

    Liquid and solid

    ( ) Liquid (variable density)

    Centrifugal type

    Blade type

    Blade type

    Centrifugal type

    Impeller type

    Plate type

    Strap type

    Hopper type

    Chain type

    Screw type

    Cordially,

    Strap type

    Hopper type

    Chain type

    Reciprocating type

    Screw type

    Vibration type

    ( ) Reciprocating type (multi-cylinder)

    ( ) Reciprocating type (single-cylinder)

    Purposes

    Diaphragm

    Rods

    Pipes

    Plastic blowing machine

    Heavy-duty

    Medium-duty

    rolling path

    ( ) Cracking machine (ores)

    Hammer type pulverizing machine

    Concrete blending machine

    * Plastic extruding

    machine

    ( ) Winding machine (winding engine)

    Colloid pressure filtering machine

    Crystal products, condenser

    * *Pulverizing machine

    * *Mixing refinery machine

    * *Refinery machine

    Rubber pressing machine

    Weaving machine

    ( ) Carding machine

    Mangling machine

    Spinning machine

    Washing machine

    24 32r/min 11kw

    1.

    2. 1.35

    11 1.35=14.85 15kw (4 ) 32r/min =43.75 43

    (N.m)= 0.90 1.35=5499.45 5499(N.m)

    i 43 5499(N.m) X9#15kw 5772(N.m)

    XLD15-9-43 X9# 15kw(4 ) 43

    1400 32

    9550 r/min

    A blender, only that liquid and solid materials are input for blending is known, works continuously for 24 hours, rotation speed is 32r/min,

    power is 11kw, how toselect the type of speed reducer and notor?

    1. type after checking load type table.

    2. 1.35 after checking working coefficient table.

    11 1.35=14.85, so power is 15kw, motor is of 4 stages, rotation speed is 32r/min, speed reduction ratio is 31/1400=43.75, therefore,

    speed reduction ratio is 43.

    To calculate maximum torque allowed on speed reducer (N.m) = Input power 9550/output rotation speed r/min efficiency coefficient,

    that is 15 9550/32 0.901.35=5499.45, taken as 5499(N.m).

    According to table of types and parameters, take i: 43, 5499(N.m), that is X9 # 15kw, 5772(N.m), as per requirements.

    Then type shall be XLD 15-9-43, that is X9 # vertical cycloid speed reducer, with motor directly coupled, power is 15kw (4 stages), speed

    reduction ratio is 43.

    15 9550 32

    1. 24

    2.

    3.

    4. (GB1096-79) h6

    5. 15

    6.

    7.

    8.

    1. The machine is available for continuous 24-hour work in a day; forward/reversed rotation is allowed.

    2. To single-stage speed reducer, rotation direction of output spindle and rotation direction of input spindle shall be contrary, and no self

    -locking function on output spindle. In conditions when Reversed rotation is likely to occur, please strictly limit rotation speed and

    torque of low-speed spindle, in order to avoid damages on parts.

    3. When coupling output spindle or input spindle, with other parts, hammering is not allowed. When triangle strap is used in transmission,

    the triangle strap shall no

Recommended

View more >