WIRE ROPE AND CHAINph: 877.STREN-FLEX (877.787.3635)

www.stren-flex.com

~ STREN-FLEX® ~ STRENGTH & FLEXIBILITY IN LIFTING

stren-fl ex.com 2

Stren-Flex® assumes no responsibility for the misuse or misapplication of any of the products contained in this catalog. Products are provided with the express understanding that the purchaser and user are thoroughly familiar with the correct application and proper use of such products in rigging.

Improper use or care of chain can result in loss of load and/or personal injury.

To avoid injury:• Do not exceed the working load limit.• Always inspect chain before use for wear, damage, and elongation. Do not impact load or jerk chain. Apply load slowly.• Protect chain from corrosion and high temperatures.• Use only alloy chain and attachments for overhead lifting.• Do not use twisted, knotted, or kinked chain.• Select the proper grade and size chain for the application.• Select attachments such as hooks to match the grade, size, and working load limit of the chain.• Be aware of the environment where the chain is being used. Extreme temperatures and corrosive media can affect the working load limit of the chain.

To avoid injury:• Do not exceed the working load limit.• Sling capacity decreases as angle from horizontal decreases. Slings should not be used at angles less than 30°.• Do not tip load or use attachments in any manner for which they were not intended.• Do not shock or dynamically load.• Do not apply load to latches. Latches are to retain slack slings and chain only.• Select attachments to match the grade, size, and working load limit of the chain.• Do not use excessively worn or damaged attachments.• Do not use mechanical coupling links to repair alloy chains used for overhead lifting.• When using master rings or master links, do not use oversize crane hooks where the link does not fit in the saddle of the hook.• When using shackles, do not side load. Centerline of the load must coincide with centerline of shackle.• Do not replace pins or bolts with other than original equipment parts.• Use only forged carbon wire rope clips for critical or lifting applications.• Do not use malleable iron wire rope clips for critical or lifting applications.• Use wire rope clips in conjunction with wire rope thimbles.• Do not move unbalanced loads.• When using load binders, do not use a cheater bar or handle extension.• Do not operate a load binder while anyone is on the load.• Release lever type load binders with extreme care. Make sure everyone is clear of the load as handle may whip suddenly.

Improper use of rigging attachments can result in bodily injury or property damage.

WARNING

stren-fl ex.com 3

Stren-Flex®

6295 McDonough DriveNorcross, GA 30093

toll free: 877.STREN-FLEX(877.787.3635)fax: 800.628.3648fax: 770.441.0326

Warning 2Wire Rope Basics 4Wire Rope — 6 x 19 Class 5Wire Rope — 6 x 37 Class 6Wire Rope — Aircraft Cable, Rotation Resistant 7Wire Rope Sling Basics 8Single Leg Wire Rope Slings 9Multiple Leg Wire Rope Bridle Slings & Thimbles 10Rigging Hooks 11Hoist Cable & Winch Lines 12Wire Rope Clips 13Shackles 14Turnbuckles 15Snatch Blocks 16Carbon Chain G43, G70 17Carbon Chain Attachments: G43, G70 18Load Binders 19Alloy Chain: G80, G100 20Alloy Chain Slings 21Alloy Chain Attachments: G80 22Wire Mesh Slings 25OSHA & ASME Reference 26Inspection Reference 27

CAUTIONAll capacities, dimensions, and other information in this catalog are subject to change without notice. Use for preliminary reference only.

SATISFACTION GUARANTEEIf you are not satisfi ed with any normally stocked Stren-Flex® product, you may return it for a full refund or credit at any time within 10 days following shipment. All items must be returned prepaid, and a return goods authorization number must be issued from the factory and included with the return. Returned items must be complete, undamaged, and in new condition. Special order items are not covered by the satisfaction guarantee and are subject to a restocking fee.

stren-fl ex.com 4

General Wire Rope ConstructionWire rope is a machine composed of a number of precise, moving parts, designed and manufactured to bear a very defi nite relation to one another. In fact, some wire ropes contain more moving parts than many complicated mechanisms. For example, a 6-strand rope with 49-wire strands laid around an independent wire rope core contains a total of 343 individual wires. All of these wires must work together and move with respect to one another if the rope is to have the fl exibility necessary for successful operation.

The Modifi ed X-chartThe two factors governing most decisions in selecting wire rope are abrasion resistance and resistance to bending fatigue. A graphic presentation of the balance between these properties has traditionally been given by means of the X-chart. However, new designs of wire rope, such as 6-Pac and Triple-Pac, do not follow the X-chart model as they are designed to provide both abrasion resistance and resistance to bending fatigue.

To read the Modifi ed X-chart, the position of each rope construction must be considered in relation to both the X and Y axes, or Abrasion Resistance and Resistance to Bending Fatigue, respectively. For example, the construction 6 x 41 (6 x 49) is in the lower right quadrant, ranking high on the bending fatigue scale. However, its position in abrasion resistance is very low.

Therefore, it can be said that a 6 x 41 (6 x 49) construction offers excellent resistance to bending fatigue, but poor resistance to abrasion. At the other end of the spectrum is a 6 x 7 construction, located in the upper right quadrant of the chart. A 6 x 7 offers excellent abrasion resistance, but very poor resistance to bending fatigue.

Wire Rope ConstructionWire rope is composed of wires, strands, a core and lubrication. The basic unit of wire rope is wire, which is carefully processed and drawn from selected grades of steel to predetermined physical properties and sizes. A predetermined number of fi nished wires is then helically laid together in a uniform geometric pattern to form a strand. This process must be performed with precision and exactness to form a strand of correct size and characteristics. The required number of suitably fabricated strands are laid symmetrically with a defi nite length of lay around a core, forming the fi nished wire rope.

Wire Rope Construction TerminologyWire rope is identifi ed by its construction, or the number of strands per rope, and number of wires in each strand. For example, the construction 6 x 25 denotes a 6-strand rope, with each strand having 25 wires. Constructions having similar weights and breaking strengths are grouped into wire rope classifi cations, such as the 6 x 19 and 6 x 37 Classes.

Strand

Core

Wire

Wire Rope

WIRE ROPE BASICS

stren-fl ex.com 5

6 x 19 Warrington with Fiber Core

6 x 19 Seale with IWRC 6 x 25 Filler Wire with IWRC

6 x 26 Warrington Seale with IWRC

6 x 19 Class Wire Rope

Strands: 6Wires per Strand: 19 to 26Core: IWRC or fi ber coreStandard Grade: Extra Improved (EIP)Lay: Regular or LangFinish: Bright or Galvanized

The 6 x 19 Classifi cation of wire rope is widely used. 6 x 19 Class wire rope is suited to the specifi c needs of diverse kinds of machinery and equipment due to its wear resistance and fl exibility. 6 x 19 Seale construction, with its large outer wires, provides greater resistance to abrasion and crushing. However, its resistance to fatigue is somewhat less than that offered by a 6 x 25 construction. The 6 x 25 possesses the best combination of fl exibility and wear resistance in the 6 x 19 Class due to the fi ller wires providing support and imparting stability to the strand. The 6 x 26 Warrington Seale construction has a high resistance to crushing. This construction is a good choice where the user needs the wear resistance of a 6 x 19 Class Rope and the fl exibility midway between a 6 x 19 Class and 6 x 37 Class rope.

WIRE ROPE — 6 X 19 CLASS

Rope Diameter

inches mm Fiber Core

Fiber CoreIWRC

IWRC

NominalBreakingStrength

NominalBreakingStrength

NominalBreakingStrength Part #Part #Part #

Approx. Weight (lb/ft)

Nominal Strength* — Tons (bright or drawn galvanized**)

EEIP IWRCEIP

04619EEIPIWRC

05619EEIPIWRC

06619EEIPIWRC

07619EEIPIWRC

08619EEIPIWRC

09619EEIPIWRC

10619EEIPIWRC

12619EEIPIWRC

14619EEIPIWRC

16619EEIPIWRC

18619EEIPIWRC

20619EEIPIWRC

22619EEIPIWRC

24619EEIPIWRC

26619EEIPIWRC

28619EEIPIWRC

30619EEIPIWRC

32619EEIPIWRC

04619EIPIWRC

05619EIPIWRC

06619EIPIWRC

07619EIPIWRC

08619EIPIWRC

09619EIPIWRC

10619EIPIWRC

12619EIPIWRC

14619EIPIWRC

16619EIPIWRC

18619EIPIWRC

20619EIPIWRC

22619EIPIWRC

24619EIPIWRC

26619EIPIWRC

28619EIPIWRC

30619EIPIWRC

32619EIPIWRC

04619EIPFC

05619EIPFC

06619EIPFC

07619EIPFC

08619EIPFC

09619EIPFC

10619EIPFC

12619EIPFC

14619EIPFC

16619EIPFC

18619EIPFC

20619EIPFC

22619EIPFC

24619EIPFC

26619EIPFC

28619EIPFC

30619EIPFC

32619EIPFC

6.5

8.0

9.5

11.0

13.0

14.5

16.0

19.0

22.0

26.0

29.0

32.0

35.0

38.0

42.0

45.0

48.0

52.0

0.105

0.164

0.236

0.32

0.42

0.53

0.60

0.95

1.29

1.68

2.13

2.63

3.18

3.78

4.44

5.15

5.91

6.72

0.116

0.18

0.26

0.35

0.46

0.59

0.72

1.04

1.42

1.85

2.34

2.89

3.50

4.16

4.88

5.67

6.50

7.39

3.74

5.80

8.31

11.20

14.60

18.50

22.70

32.30

43.80

56.90

71.50

87.90

106.00

125.00

146.00

169.00

192.00

217.00

3.02

4.69

6.71

9.09

11.80

14.90

18.30

26.20

35.40

46.00

57.90

71.00

85.40

101.00

118.00

136.00

155.00

176.00

3.40

5.27

7.55

10.20

13.30

16.80

20.60

29.40

39.80

51.70

65.00

79.90

96.00

114.00

132.00

153.00

174.00

198.00

SPECIFICATIONS — 6 x 19 CLASS WIRE ROPE

* Acceptance strength is not less than 2½% below the nominal strengths listed.** Galvanizing: for Class A galvanized wire rope (EIP grade only), deduct 10% from the nominal strength shown.

6 x 19 Class6 x 19 Seale6 x 19 Warrington6 x 21 Filler Wire Type U6 x 21 Seale6 x 25 Filler Wire Type W6 x 25 Seale6 x 26 Warrington Seale

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1-5/8

1-3/4

1-7/8

2

6 x 31 Warrington Seale with IWRC

6 x 36 Warrington Sealewith IWRC

6 x 49 Filler Wire Sealewith IWRC

stren-fl ex.com 6

04637EIPIWRC

05637EIPIWRC

06637EIPIWRC

07637EIPIWRC

08637EIPIWRC

09637EIPIWRC

10637EIPIWRC

12637EIPIWRC

14637EIPIWRC

16637EIPIWRC

18637EIPIWRC

20637EIPIWRC

22637EIPIWRC

24637EIPIWRC

26637EIPIWRC

28637EIPIWRC

30637EIPIWRC

32637EIPIWRC

WIRE ROPE — 6 X 37 CLASS

6 x 37 Class Wire Rope

Strands: 6Wires per Strand: 27 to 49Core: IWRC or Fiber CoreStandard Grade: Extra Improved (EIP)Lay: Regular or LangFinish: Bright or Galvanized

The 6 x 37 Class of wire rope is characterized by the relatively large number of wires used in each strand. Ropes of this class are among the most fl exible available due to the greater number of wires per strand, however their resistance to abrasion is less than ropes in the 6 x 19 Class.

inches mm Fiber CoreIWRCPart #Part #

04637EEIPIWRC

05637EEIPIWRC

06637EEIPIWRC

07637EEIPIWRC

08637EEIPIWRC

09637EEIPIWRC

10637EEIPIWRC

12637EEIPIWRC

14637EEIPIWRC

16637EEIPIWRC

18637EEIPIWRC

20637EEIPIWRC

22637EEIPIWRC

24637EEIPIWRC

26637EEIPIWRC

28637EEIPIWRC

30637EEIPIWRC

32637EEIPIWRC

04637EIPFC

05637EIPFC

06637EIPFC

07637EIPFC

08637EIPFC

09637EIPFC

10637EIPFC

12637EIPFC

14637EIPFC

16637EIPFC

18637EIPFC

20637EIPFC

22637EIPFC

24637EIPFC

26637EIPFC

28637EIPFC

30637EIPFC

32637EIPFC

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1-5/8

1-3/4

1-7/8

2

6.5

8.0

9.5

11.0

13.0

14.5

16.0

19.0

22.0

26.0

29.0

32.0

35.0

38.0

42.0

45.0

48.0

52.0

0.105

0.164

0.236

0.32

0.42

0.53

0.60

0.95

1.29

1.68

2.13

2.63

3.18

3.78

4.44

5.15

5.91

6.72

0.116

0.18

0.26

0.35

0.46

0.59

0.72

1.04

1.42

1.85

2.34

2.89

3.50

4.16

4.88

5.67

6.50

7.39

3.74

5.80

8.31

11.20

14.60

18.50

22.70

32.30

43.80

56.90

71.50

87.90

106.00

125.00

146.00

169.00

192.00

217.00

3.02

4.69

6.71

9.09

11.80

14.90

18.30

26.20

35.40

46.00

57.90

71.00

85.40

101.00

118.00

136.00

155.00

176.00

3.40

5.27

7.55

10.20

13.30

16.80

20.60

29.40

39.80

51.70

65.00

79.90

96.00

114.00

132.00

153.00

174.00

198.00

SPECIFICATIONS — 6 x 37 CLASS WIRE ROPE

* Acceptance strength is not less than 2½% below the nominal strengths listed.** Galvanizing: for Class A galvanized wire rope (EIP grade only), deduct 10% from the nominal strength shown.

6 x 37 Class6 x 31 Warrington Seale 6 x 33 Warrington Seale6 x 36 Warrington Seale 6 x 41 Warrington Seale 6 x 43 Filler Wire Seale6 x 49 Filler Wire Seale

Rope Diameter

Fiber CoreIWRCNominalBreakingStrength

NominalBreakingStrength

Approx. Weight (lb/ft)

Nominal Strength* — Tons (bright or drawn galvanized**)

EEIP IWRCEIP

Part #

NominalBreakingStrength

stren-fl ex.com 7

7 x 7 7 x 19

WIRE ROPE — AIRCRAFT CABLE, ROTATION RESISTANT

Strands: 19Wires per Strand: 7Core: WSC 19 x 7 is recommended for hoisting unguided loads with a single-part line. The rotation-resistant properties of this rope are secured by two layers of strands. The inner strands are left lay, while the 12 outer strands are right lay, which enables one layer to counteract the other layer’s rotation. The rotation-resistant characteristics of the 19 x 7 wire ropes are superior to those of the 8 x 19 Class wire ropes.

Strands: 8Wires per Strand: 19 to 25Core: IWRC 8 x 19 Classifi cation rotation-resistant ropes are recommended for hoisting unguided loads with a single-part or multi-part line. Outer strands are right lay and inner strands are left lay. 8 x 19 ropes are slightly stronger and signifi cantly more rugged than the 19 x 7 construction. However, the rotation-resistant properties of the 8 x 19 rotation-resistant ropes are much less than those of the 19 x 7 construction. 8 x 19 Seale and 8 x 25 Filler Wire constructions available.

Rope Diameter

Wire Rope Class

Rope Diameter

inches

inches

mm

mm

Part #

Part #

Approx. Weight

Cable Dia.Approx. Weightper 1,000 foot

Approx. Weight

4.8

6.5

8.0

9.5

11.0

13.0

14.5

16.0

19.0

22.0

26.0

29.0

32.0

35.0

38.0

7.51628436217294565

110173243

IMWR0177*ACIMWR01577*ACIMWR0277*ACIMWR02577*ACIMWR0377*ACIMWR015719*ACIMWR02719*ACIMWR025719*ACIMWR03719*ACIMWR04719*ACIMWR05719*ACIMWR06719*AC

13.0

14.5

16.0

19.0

22.0

26.0

29.0

32.0

35.0

38.0

0.064

0.113

0.177

0.250

0.350

0.450

0.580

0.710

1.020

1.390

1.820

2.300

2.840

3.430

4.080

480920

170026003700100020002800420070009800

14400

480920

170026003700

-17602400370064009000

12000

0.47

0.60

0.73

1.06

1.44

1.88

2.39

2.94

3.56

4.24

1.57

2.77

4.30

6.15

8.33

10.80

13.60

16.80

24.00

32.50

42.20

53.10

65.10

78.40

92.80

11.7

14.7

18.1

25.9

35.0

45.5

57.3

70.5

84.9

100.0

SPECIFICATIONS — AIRCRAFT CABLE

SPECIFICATIONS — 19 x 7 CLASS WIRE ROPE

SPECIFICATIONS — 8 x 19 CLASS WIRE ROPE

* Acceptance strength is not less than 2½% below the nominal strengths listed.

* Insert (G) for Galvanized or (SS) for Stainless Steel.

03197EIPWSC

04197EIPWSC

05197EIPWSC

06197EIPWSC

07197EIPWSC

08197EIPWSC

09197EIPWSC

10197EIPWSC

12197EIPWSC

14197EIPWSC

16197EIPWSC

18197EIPWSC

20197EIPWSC

22197EIPWSC

24197EIPWSC

08819EIPIWRC

09819EIPIWRC

10819EIPIWRC

12819EIPIWRC

14819EIPIWRC

16819EIPIWRC

18819EIPIWRC

20819EIPIWRC

22819EIPIWRC

24819EIPIWRC

Nominal Strength*

EIP

Nominal Breaking Strength (lbs) Part #

Nominal Strength*

EIP

tons

tons

3/16

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1/163/32

1/85/323/163/32

1/85/323/16

1/45/16

3/8

7 x

77

x 19

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

lb/ft

GAC SS

lb/ft

Galvanized Aircraft Cable (GAC) and Stainless Steel Aircraft Cable (SSAC).

19 x 7 Class Rotation-Resistant Wire Rope

8 x 19 Class Rotation-Resistant Wire Rope

Standard Grade: Extra Improved (EIP)Lay: Right RegularFinish: Bright

Standard Grade: Extra Improved (EIP)Lay: RegularFinish: Bright

Strands: 7Wires per Strand: 7 or 19

lbin.

stren-fl ex.com 8

Length = pull to pull

FLEMISH EYE WITH MECHANICAL SPLICE.

BASIC SLING HITCHES

Vertical Choker Basket

Stren-Flex® wire rope slings are manufactured to comply with our own strict quality control and testing standards. All Stren-Flex® products are manufactured exclusively in the United States with the highest quality imported and domestic materials and components.

Stren-Flex® manufactures all products with a simple mission — to provide the highest quality, most durable, and safest material handling device available. Further, every Stren-Flex® lifting product undergoes a thorough inspection and rigorous quality control testing. All Stren-Flex® products exceed current OSHA and ANSI standards — making Stren-Flex® lifting products the leader when it comes to “strength and fl exibility” in the rigging industry.

How to order wire rope slings:1. Determine the weight of the load.

2. Determine the type of hitch to be used. One of the basic hitches (top

right) is suitable for most lifts.

3. Determine the type of sling to be used. (Will the sling have eyes, hooks

or thimbles?)

4. Length of the sling measured from pull to pull.

5. Wire rope construction if not standard 6 x 19 or 6 x 37.

6. Double check diameter, length and sling type with the WLL

(Working Load Limit).

WIRE ROPE SLING BASICS

Wire rope slings are strong, effi cient and reliable accessories in the material handling industry. Wire rope functions as an excellent sling material in applications where a combination of strength and abrasion are necessary. Wire rope slings are available in an array of lengths and confi gurations to fi t almost any application. Stren-Flex® features wire rope slings made with high quality domestic wire rope that are tagged with all appropriate ASME information and capacities. Import wire rope slings are also available.

Wire Rope Sling Types

Eye & EyeEE

Thimble & Thimble TT

Eye & HookEH

Thimble & Hook TH

Slip Thru & Slip Thru Thimbles

STST

Sliding ChokerEye & EyeE/E/SCH

Sliding ChokerEye & Thimble

E/T/SCH

Crescent &Crescent Thimbles

CTCT

Eye & Thimble ET

stren-fl ex.com 9

WireRope Class

Rope Dia.(in.) Domestic Part # Import Part #

Min. Sling Length w/ Standard Eyes

WRS04^^**

WRS05^^**

WRS06^^**

WRS07^^**

WRS08^^**

WRS09^^**

WRS10^^**

WRS12^^**

WRS14^^**

WRS16^^**

WRS18^^**

WRS20^^**

WRS22^^**

WRS24^^**

IMWRS04^^**

IMWRS05^^**

IMWRS06^^**

IMWRS07^^**

IMWRS08^^**

IMWRS09^^**

IMWRS10^^**

IMWRS12^^**

IMWRS14^^**

IMWRS16^^**

IMWRS18^^**

IMWRS20^^**

IMWRS22^^**

IMWRS24^^**

1’ 6”

1’ 9”

2’ 0”

2’ 3”

2’ 6”

2’ 9”

3’ 0”

3’ 6”

4’ 0”

4’ 6”

5’ 0”

5’ 6”

6' 0"

7’ 0”

SPECIFICATIONS — SINGLE LEG WIRE ROPE SLINGS

* Call Stren-Flex® for reduced choker capacity when using sliding choker hooks.^^ Insert Length when ordering.** Insert Type when ordering.

* Call Stren-Flex® for reduced choker capacity when using sliding choker hooks.** See page 22 for oblong specifi cations & dimensions.

Single Leg Rated Capacity (Tons)

Vertical Choker Basket

0.65

1

1.4

1.9

2.5

3.2

3.9

5.6

7.6

9.8

12

15

18

21

0.48

0.74

1.1

1.4

1.9*

2.4

2.9*

4.1*

5.6

7.2

9.1

11

13

16*

1.3

2

2.8

3.8

5

6.4

7.8

11

15

19.6

24

30

36

42

WireRope Class

Rope Dia.(in.)

Oblong Size**(in.)

.437

.437

.437

.437

.512

.63

.63

.75

.875

1.024

1.024

1.25

1.25

1.5

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

DIMENSIONS — SINGLE LEG WIRE ROPE SLINGS

6 x

196

x 37

Standard Eye Size W x L

(in.)

Thimble Eye Size W x L(in.)

Eye Hook Capacity W x L(tons)

Slip-thru Thimble Eye Size W x L

(in.)

Crescent Thimble Eye Size W x L

(in.)Sliding Choker Hook (in.)

2 x 4

2-1/2 x 5

3 x 6

3-1/2 x 7

4 x 8

4-1/2 x 9

5 x 10

6 x 12

7x 14

8 x 16

9 x 18

10 x 20

11 x 22

12 x 24

7/8 x 1-5/8

1-1/16 x 1-7/8

1-1/8 x 2-1/8

1-1/4 x 2-1/4

1-1/2 x 2-3/4

1-1/2 x 2-3/4

1-3/4 x 3-1/4

2 x 3-3/4

2-1/4 x 4-1/4

2-1/2 x 4-1/2

2-7/8 x 5-1/8

2-7/8 x 5-1/8

3-1/2 x 6-1/4

3-1/2 x 6-1/4

1

1

1-1/2

2

3

4-1/2

4-1/2

7

11

11

15

15

22

22

2-1/8 x 4-1/8

2-1/8 x 4-1/8

2-1/8 x 4-1/8

2-3/8 x 4-3/8

2-3/8 x 4-3/8

2-3/8 x 4-3/8

3-3/8 x 6-5/8

3-3/8 x 6-5/8

3-3/4 x 7-1/8

3-3/4 x 7-1/8

4-3/8 x 8-3/8

4-3/8 x 8-3/8

5 x 9-1/2

5 x 9-1/2

2 x 4

2 x 4

2 x 4

2 x 5

2-1/4 x 6

2-1/4 x 7

2-3/4 x 7

3-1/4 x 8-1/2

4-1/2 x 10

4-1/2 x 11-1/2

4-7/8 x 13

5-1/2 x 14-1/2

6 x 16

6 x 17-1/2

3/8

3/8

3/8

1/2

1/2*

5/8

5/8*

3/4*

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2*

SINGLE LEG WIRE ROPE SLINGS

6 x

196

x 37

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

stren-fl ex.com 10

2-Leg Bridle 3-Leg Bridle 4-Leg Bridle

MULTIPLE LEG WIRE ROPE BRIDLE SLINGS & THIMBLES

MULTIPLE LEG WIRE ROPE BRIDLE SLINGS

* Working Load Limit, based on standard carbon fi ttings unless otherwise noted.** See page 22 for oblong specifi cations & dimensions.

Rope Class

Rope Dia.(in.)

Min. Leg Length (ft)

EIP, IWRCTwo Legs Three Legs Four Legs

60˚ 60˚ 60˚45˚ 45˚ 45˚30˚ 30˚ 30˚

Hook WLL* (tons) Oblong

Size**(in.)

Oblong Size**(in.)

Oblong Size**(in.)

WLL (tons) WLL (tons) WLL (tons)

1.5

2

2

2.5

2.5

3

3

3.5

4

4.5

5.0

5.0

5.5

6

1.1

1.7

2.5

3.5

4.4

5.5

6.8

9.7

13

17

21

26

31

37

1.7

2.6

3.7

5

6.6

8.3

10

15

20

26

31

38

46

55

2.2

3.5

5

6.7

8.8

11

14

19

26

34

42

51

62

73

.91

1.4

2

2.7

3.6

4.5

5.5

7.9

11

14

17

21

25

30

1.4

2.1

3

4.1

5.4

6.8

8.3

12

16

21

26

31

38

45

1.8

2.8

4.1

5.5

7.1

9

11

16

21

28

34

42

50

60

.65

1

1.4

1.9

2.5

3.2

3.9

5.6

7.6

9.8

12

15

18

21

3/4

1

1-1/2

2

3

3

5

5

7-1/2

10

10

15

15

22

.437

.437

.512

.512

.63

.75

.75

1.024

1.024

1.250

1.500

1.500

1.750

2.000

.437

.512

.630

.750

.750

.875

1.024

1.260

1.500

1.500

1.750

2.000

2.000

2.250

.512

.630

.750

.750

1.024

1.024

1.260

1.500

1.500

1.750

2.000

2.250

2.500

2.500

.97

1.5

2.2

2.9

3.8

4.8

5.9

8.4

11

15

18

22

27

32

1.3

2

2.9

3.9

5.1

6.4

7.8

11

15

20

24

30

36

42

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

6 x

196

x 37

Length

A

D

C

E

BD

Rope Diameter Part #

Standard Pack

25

25

25

25

10

10

10

IMTH04

IMTH05

IMTH06

IMTH08

IMTH10

IMTH12

IMTH14

2.19

2.5

2.88

3.63

4.25

5

5.5

1.5

1.81

2.13

2.56

3

3.5

4

1.63

1.88

2.13

2.75

3.25

3.75

4.25

0.88

1.06

1.13

1.5

1.75

2

2.25

0.41

0.5

0.66

0.84

1

1.25

1.38

0.075

0.14

0.25

0.51

0.75

1.47

1.85

1/4

5/16

3/8

1/2

5/8

3/4

7/8

A(in.)

B(in.)

C(in.)

D(in.)

E(in.)

Weight(lb)

HEAVY DUTY WIRE ROPE THIMBLES (HOT GALVANIZED)

C

L R

B

A

K

G

H KD

T

OJ

C

LR

B

A

I

G

H

S

D

T

O

stren-fl ex.com 11

Alloy Carbon

WLL(lb)

Hook Part #

LatchPart #

WLL(lb)

Hook Part #

LatchPart #

A(in.)

B(in.)

C(in.)

D(in.)

G(in.)

H(in.)

I(in.)

L(in.)

R(in.)

S(in.)

T(in.)

O(in.)

Weight(lb)

Dimensions

Rigging Hook• Built-in distortion detectors• Design factor 5:1• Load rating marked on each hook body• Hook and latch assemblies furnished separately• Carbon hooks have a clear protective coating to resist rust and for cleaner handling (use suffi x "C" when ordering carbon clear fi nish, use suffi x "G" when ordering hot dip galvanized).

Alloy Carbon

WLL(lb)

Hook Part #

LatchPart #

WLL(lb)

Hook Part #

LatchPart #

A(in.)

B(in.)

C(in.)

D(in.)

G(in.)

H(in.)

J(in.)

K(in.)

L(in.)

O(in.)

R(in.)

T(in.)

Weight(lb)

2,205

3,308

4,410

6,615

11,025

15,435

24,255

33,075

48,510

1,654

2,205

3,308

4,410

6,615

11,025

16,538

20,500

33,075

1.50

1.75

2.13

2.50

3.06

3.88

4.69

5.34

6.63

0.75

0.88

1.13

1.25

1.56

2.00

2.44

2.84

3.50

0.38

0.44

0.50

0.63

0.75

0.94

1.13

1.25

1.56

3.06

3.33

3.67

4.20

5.11

6.24

7.89

8.37

10.19

0.87

0.94

1.06

1.27

1.44

1.82

2.25

2.59

3.00

1.05

1.11

1.21

1.43

1.63

2.01

2.63

2.94

3.50

0.93

0.97

1.06

1.19

1.50

1.78

2.38

2.50

3.30

0.63

0.71

0.88

0.94

1.31

1.68

1.88

2.19

2.69

4.37

5.04

5.63

6.55

7.97

10.07

12.41

14.05

17.37

0.93

0.97

1.06

1.16

1.41

1.69

2.19

2.30

3.12

3.13

3.66

4.09

4.67

5.78

7.31

9.03

10.21

12.81

0.87

0.97

1.03

1.16

1.53

1.94

2.52

2.54

2.73

0.66

1.12

1.46

2.42

4.10

8.16

15.60

21.58

39.89

M6402A

M6403A

M6404A

M6405A

M6407A

M6409A

M6411A

M6415A

M6422A

M6402C

M6403C

M6404C

M6405C

M6407C

M6409C

M6411C

M6415C

M6422C

4X1302

4X1303

4X1304

4X1305

4X1307

4X1309

4X1311

4X1315

4X1322

4X1302

4X1303

4X1304

4X1305

4X1307

4X1309

4X1311

4X1315

4X1322

Dimensions

Swivel Rigging Hook• Built-in distortion detectors• Design factor 5:1• Hook and latch assemblies furnished separately• Painted orange• Carbon swivel hooks are technically advanced Micro-alloy which requires no secondary heat treat• Alloy swivel hooks are heat-treated quenched and tempered

2,205

3,308

4,410

6,615

11,025

15,435

24,255

33,060

48,488

1,654

2,205

3,308

4,410

6,615

11,025

15,435

22,040

33,060

2.00

2.50

3.00

3.00

3.50

4.75

5.50

6.00

7.75

1.11

1.38

1.65

1.65

1.77

2.39

2.55

2.47

3.82

1.25

1.50

1.75

1.75

2.00

2.75

3.25

3.50

4.75

3.06

3.33

3.67

4.20

5.11

6.24

7.69

8.37

10.19

0.87

0.94

1.06

1.27

1.44

1.82

2.25

2.59

3.00

1.05

1.11

1.21

1.43

1.63

2.01

2.63

2.94

3.50

0.63

0.71

0.88

0.94

1.31

1.68

1.88

2.19

2.69

5.83

6.83

7.76

8.40

9.76

12.42

14.89

15.79

21.18

4.63

5.44

6.25

6.49

7.53

9.67

12.06

11.95

16.68

0.38

0.50

0.63

0.63

0.75

1.00

1.13

1.25

1.50

0.87

0.97

1.03

1.16

1.53

1.94

2.46

2.62

2.74

0.93

0.97

1.06

1.16

1.41

1.69

2.22

2.23

3.05

1.05

1.56

2.50

3.20

5.36

10.56

19.00

26.75

51.80

M3402A

M3403A

M3404A

M3405A

M3407A

M3409A

M3411A

M3415A

M3422A

M3402C

M3403C

M3404C

M3405C

M3407C

M3409C

M3411C

M3415C

M3422C

4X1302

4X1303

4X1304

4X1305

4X1307

4X1309

4X1311

4X1315

4X1322

4X1302

4X1303

4X1304

4X1305

4X1307

4X1309

4X1311

4X1315

4X1322

RIGGING HOOKS

B

A

stren-fl ex.com 12

AFTER SWAGE DIMENSIONS

WINCH LINE SPECIFICATIONS

HOIST CABLE & WINCH LINES

Rope Dia.(in.) Part # A B

ASC-1060-6

ASC-1426-1.00

ASC-1060-8A

ASC-1060-8

ASC-1184-.75

ASC-1278-1.06

ASC-1060-10A

ASC-1060-10

ASC-FB-10-2

ASC-1255

ASC-1064-1.10

ASC-1092-1.22

ASC-1104-.94

ASC-1094

ASC-1060-12A

ASC-1060-12

ASC-1256-1.75

ASC-1060-14

ASC-4150

ASC-1959

ASC-1060-16A

ASC-1060-16

ASC-1356

ASC-4016

ASC-1060-18

3/16

1/4

5/16

3/8

7/16

9/16

1/2

1/2

3/4

1/2

5/8

3/4

1

5/8

3/4

11/16

7/8

7/8

1

1

3/4

3/4

7/8

7/8

1

1-1/8

7/8

1

1-1/8

1

1-1/8

1-1/4

7/8

1-1/8

1-1/8

1-1/8

1

1-1/4

1-3/8

1-1/2

1

7/8

1-5/16

1-1/2

1-3/16

1-9/16

1-3/4

1-3/4

1-3/4

2

2

2-1/2

2-1/4

2-3/8

2-1/2

2-1/4

2-1/2

Hoist Cable AssembliesStren-Flex® manufactures replacement cables for wire rope hoists. Hoist cable assemblies can be made to custom specifi cations given construction, length, and fi ttings needed. Ferrule sizes other than those shown are available.

Winch LinesWinch lines are typically made with 6 x 19 construction wire rope with an independent wire rope core for improved strength and abrasion resistance. For more fl exibility, wire rope with a fi ber core can be used.

• High quality fl emish eye splice with mechanical swage• Heavy duty thimble eye• Carbon or alloy hooks with latch

Cable Diameter

(in.)

Hook Capacity(ton)Part #

Nominal Breaking Strength (lbs)

Fiber Core IWRC

13,420

18,180

23,600

29,800

36,600

3

4.5

4.5

4.5

7

3/8

7/16

1/2

9/16

5/8

IMWL06X**^^3TSH

IMWL07X**^^4.5TSH

IMWL08X**^^4.5TSH

IMWL09X**^^4.5TSH

IMWL10X**^^7TSH

15,100

20,400

26,600

33,600

41,200

* See page 11 for Hook Specifi cations and Dimensions** Insert Cable Length^^ Insert (FC) for Fiber Core or (SC) for IWRC

B

C

E

FGH

D A

stren-fl ex.com 13

WIRE ROPE CLIPS

Dimensions

Size(in.)

Size(in.)

Part #

Min. Clips Req'd.

Part #

C(in.)

Approx. Weight

(lb)

D(in.)

E(in.)

F(in.)

A(in.)

Amt. Wire Rope to turn back (in.)

B(in.)

Torque(ft/lb)

G(in.)

H(in.)

Min. No. Clips

A B C D E F G

Rope Turnbuckle

Torque(ft/lb)

Weight(lb)

1/8*

3/16*

1/4

5/16

3/8

7/16

1/2

9/16

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1/16*1/8*3/161/45/163/87/161/29/165/83/47/811-1/8

7/16

9/16

1/2

3/4

3/4

1

1

1-1/4

1-1/4

1-7/16

1-5/8

1-13/16

2

2-1/8

2-5/16

2-3/8

.03

.04.063

.13

.15

.21

.37

.37

.59

.59

.841.251.662.43

15/32

19/32

3/4

7/8

1

1-3/16

1-3/16

1-5/16

1-5/16

1-1/2

1-3/4

1-7/8

2

2-5/16

2-3/8

2-19/32

.15

.18

.25

.31

.31

.38

.44

.44

.5

.5

.56

.63

.63

.75

13/32

1/2

31/32

23/32

29/32

1-1/16

1-1/8

1-1/4

1-11/32

1-7/16

1-19/32

1-25/32

1-25/32

2-3/16

2-1/4

2-1/2

.65

.81

.941.191.311.63

22

2.312.312.563.063.44

4

3/8

1/2

9/16

11/16

3/4

7/8

7/8

15/16

15/16

1-1/16

1-1/4

1-1/4

1-1/4

1-7/16

1-7/16

1-7/16

.45.5

.56

.75

.841

1.191.191.381.381.561.81

22.75

13/16

15/16

1-3/16

1-5/16

1-5/8

1-25/32

1-29/32

1-31/32

2

2-11/32

2-7/16

2-5/8

2-13/16

3-1/8

3-1/8

3-1/8

.38.5

.56

.75

.75

.881.061.061.251.251.311.631.88

2

15/16

1-5/32

1-7/16

1-11/16

1-15/16

2-5/16

2-5/16

2-1/2

2-1/2

2-13/16

3-5/32

3-5/32

3-19/32

4-1/8

4-1/4

4-7/16

.38.5

.56

.69

.75

.8411

1.251.251.441.752.062.19

2

2

2

2

2

2

3

3

3

4

4

5

6

7

7

8

.45

.56

.63

.75

.75

.881.061.061.281.281.561.81

22.06

4-1/2

7-1/2

15

30

45

65

65

95

95

130

225

225

225

360

360

360

.69

.941.061.311.441.631.881.882.092.092.382.88

33.38

3-1/4

3-3/4

4-3/4

5-1/4

6-1/2

7

11-1/2

12

12

18

20

26

34

37

44

48

5

9

18

30

42

70

75

100

100

150

240

250

310

460

520

590

M244

M245

M246

M247

M248

M249

M250

M296

M251

M252

M253

M254

M255

M256

M257

M258

33333344445567

IMMC01IMMC02IMMC03IMMC04IMMC05IMMC06IMMC07IMMC08IMMC09IMMC10IMMC12IMMC14IMMC16IMMC18

23/32

31/32

1-1/32

1-3/8

1-1/2

1-7/8

1-7/8

2-3/8

2-3/8

2-3/4

3-1/8

3-1/2

3-7/8

4-1/4

4-5/8

4-15/16

23

4.51515304045507575

130130200

12 - 24

1/4 - 20

5/16 - 18

3/8 - 16

7/16 - 14

1/2 - 13

1/2 - 13

9/16 - 12

9/16 - 12

5/8 - 11

3/4 - 10

3/4 - 10

3/4 - 10

7/8 - 9

7/8 - 9

7/8 - 9

44-3/45-1/277-3/49-1/210-1/415-1/4161622-1/423-1/23139

Malleable Wire Rope ClipsUsed for light duty, non-critical applications only. Typical uses include guard lines and fencing. Do not use malleable wire rope clips for critical or lifting applications. Load may be suddenly released resulting in injury or death.

Dimensions (in.)*

1/16" and 1/8" are not covered by Federal Specifi cation FF-C-450 D. CAUTION: Never use any wire rope clip to directly connect two straight lengths of wire rope.* Dimensions may vary.

Proper use of wire rope clips

1 2 3

DROP FORGED WIRE ROPE CLIPS

G

B

D

F

C

A

E

E

D B

R W

L

P

stren-fl ex.com 14

Round Pin

Chain Shackles

Safety (Bolt & Nut)

Web Shackles

SHACKLES

Working Load Limit (tons)Size(in.)

Size(in.)

CMCarbon

CMAlloy

CM Carbon

Import Carbon

CM Alloy Import Carbon

P*(in.)

E*(in.)

W*(in.)

R*(in.)

L*(in.)

B min.*(in.)

Weight*(lb)

3/16

1/4

5/16

3/8

7/16

1/2

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1-5/8

1-3/4

2

3/16

1/4

5/16

3/8

7/16

1/2

5/8

3/4

7/8

1

1-1/8

1-1/4

1-3/8

1-1/2

1-5/8

1-3/4

2

0.250

0.312

0.375

0.438

0.5

0.625

0.75

0.875

1

1.125

1.25

1.375

1.5

1.625

1.75

2

2.25

0.307

0.401

0.463

0.531

0.593

0.718

0.843

0.968

1.109

1.234

1.375

1.531

1.656

1.781

1.906

2.156

2.406

0.375

0.469

0.531

0.656

0.75

0.813

1.063

1.25

1.438

1.688

1.812

2.031

2.25

2.375

2.625

2.875

3.25

0.625

0.875

1

1.125

1.25

1.375

1.875

2.125

2.375

2.625

2.875

3.25

3.5

3.75

4.125

4.5

5.25

0.875

1.125

1.25

1.437

1.689

1.875

2.375

2.813

3.312

3.75

4.25

4.688

5.25

5.75

6.25

7

7.75

0.562

0.75

0.812

0.937

1.062

1.187

1.5

1.75

2

2.312

2.625

2.875

3.25

3.375

4

4.5

5.25

0.06

0.12

0.2

0.3

0.5

0.75

1.3

2.3

3.5

5

7

9.5

12.5

17.2

23.5

27.7

39

1/2

3/4

1

1-1/2

2

3

4-1/2

6-1/2

8-1/2

10

12

14

17

20

24

30

35

n/a

n/a

n/a

2

2.6

3.3

5

7

9.5

12.5

15

18

21

30

35

40

50

1/3

1/2

3/4

1

1-1/2

2

3-1/4

4-3/4

6-1/2

8-1/2

9-1/2

12

13-1/2

17

24

25

35

n/a

n/a

n/a

M648A*

M649A*

M650A*

M651A*

M652A*

M653A*

M654A*

M655A*

M656A*

M666A*

M657A*

M685A*

M677A*

M658A*

M645*

M646*

M647*

M648*

M649*

M650*

M651*

M652*

M653*

M654*

M655*

M656*

M666*

M657*

M685*

M677*

M658*

IMSPASCG03

IMSPASCG04

IMSPASCG05

IMSPASCG06

IMSPASCG07

IMSPASCG08

IMSPASCG10

IMSPASCG12

IMSPASCG14

IMSPASCG16

IMSPASCG18

IMSPASCG20

IMSPASCG22

IMSPASCG24

IMSPASCG26

IMSPASCG28

IMSPASCG32

SHACKLES

SHACKLE PART NUMBERS

• All CM shackles meet or exceed Federal Specifi cation RRC-271D• Working Load Limit shown as permanent marking on body• Available in painted, galvanized and self-colored fi nishes (CM only). Import models available in galvanized fi nish only.• Alloy pin• Heat treated and tempered

OTHER TYPES AVAILABLE:

* Dimensions & weights are for CM shackles. Import models may vary.

* Insert (P) for Painted fi nish; (G) for Galvanized fi nish; blank for self-colored.

stren-fl ex.com 15

TURNBUCKLES

1/4

5/16

3/8

1/2

5/8

3/4

1/4

5/16

3/8

1/2

5/8

3/4

1/4

5/16

3/8

1/2

5/8

3/4

.25

.31

.38

.50

.63

.75

.34

.44

.53

.72

.88

1.00

.63

.88

.88

1.06

1.31

1.50

.41

.44

.53

.69

.84

1.00

.22

.28

.34

.44

.50

.63

.28

.28

.31

.41

.50

.56

.45

.50

.56

.66

.84

.97

.78

.94

1.13

1.44

1.75

2.13

.41

.47

.50

.63

.75

.94

1.66

1.91

2.28

2.84

3.53

4.31

1.78

2.19

2.56

3.22

3.88

4.69

.28

.28

.31

.41

.50

.56

.50

.50

.59

.75

1.03

1.28

1.63

2.00

2.19

2.75

3.50

4.13

.63

.69

.81

1.00

1.31

1.63

A A AB B BC C CD D DE E E F G H

Dimensions (in.) Dimensions (in.) Dimensions (in.)

BODIES/STUB END TURNBUCKLES

Size (in)(Diameter x Take-Up)

Size (in)Diameter (A)

x Take-Up (B)

Approx. Weight (lb)Working Load Limit (lb)

Dimensions (in.)

Hook & HookHook & Eye

C

Jaw & JawJaw & Eye

Approx. Weight

each Body only (lb)

Approx. Weight

each Stub end (lb)

Average Overall Length with Ends in Closed Position

E F*

Eye & EyeJaw & EyeJaw & Eye

D

1/4 x 4

5/16 x 4-1/2

3/8 x 6

1/2 x 6

1/2 x 9

1/2 x 12

5/8 x 6

5/8 x 9

5/8 x 12

3/4 x 6

3/4 x 9

3/4 x 12

IMTB0404**

IMTB0504**

IMTB0606**

IMTB0806**

IMTB0809**

IMTB0812**

IMTB1006**

IMTB1009**

IMTB1012**

IMTB1206**

IMTB1209**

IMTB1209**

3/8 x 6

1/2 x 6

1/2 x 9

1/2 x 12

5/8 x 6

5/8 x 9

5/8 x 12

3/4 x 6

3/4 x 9

3/4 x 12

8.25

9.56

11.88

13.31

16.31

19.31

15.50

18.50

21.50

17

20

23

Eyes and/or Hooks

Part #

Working Load Limit

(lb)

.3

.5

.75

1.5

1.75

2.18

2.63

3

3.25

3.75

4.5

5.75

1,200

2,200

2,200

2,200

3,500

3,500

3,500

5,200

5,200

5,200

.3

.53

.82

1.62

1.82

2.19

2.69

3.01

3.5

4.25

5

5.75

.3

.6

.8

1.0

1.0

1.2

1.4

1.2

1.6

2.1

.4

.58

.93

1.68

1.85

2.2

2.82

3.25

3.75

4.68

5.38

6.12

.7

1.4

1.7

1.8

2.0

2.5

3.1

3.3

4.0

4.8

400

700

1,000

1,500

1,500

1,500

2,250

2,250

2,250

3,000

3,000

3,000

7.13

7.50

10.50

13.50

7.88

10.88

13.88

8.25

11.25

14.25

4.44

4.25

4.25

4.25

4.06

4.06

4.06

4.38

4.38

4.38

.56

.75

.75

.75

.94

.94

.94

1.13

1.13

1.13

16

16

19

22

16

19

22

17

20

23

500

800

1,200

2,200

2,200

2,200

3,500

3,500

3,500

5,200

5,200

5,200

** Specify type: (EE) Eye & Eye; (HH) Hook & Hook; (HE) Hook & Eye; (JJ) Jaw & Jaw; (JE) Jaw & Eye.Hooks not supplied on sizes larger than 1-1/2" diameter. Jaw ends up to 5/8". Fitted with bolt and nut. Jaw ends 3/4" & up: fi tted with pin and cotter.

* Closed position.

EYE & EYE (EE)

HOOK & HOOK (HH)

HOOK & EYE (HE)

JAW & JAW (JJ)

JAW & EYE (JE)

JAWEYEHOOK

B

E EG

DA

A

AA

A

E

E

D D

B B

D

C CF

A

A

F

C BE

ED

H

D

C

B

STUB END

BODY ONLY

stren-fl ex.com 16

SNATCH BLOCKS

Sheave Snatch Block Specifi cationsWorking

Load Limit(tons)

Block w/ Swivel HookWire Rope Size (in.)

Part # SheaveO.D. (in.)

Weight(lb)

5/16 - 3/8

3/8 - 1/2

3/8 - 1/2

3/8 - 1/2

3/8 - 1/2

3/8 - 1/2

3/8 - 1/2

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

1 1/8 - 1 1/4

1 1/8 - 1 1/4

3/8 - 1/2

3/8 - 1/2

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

5/8 - 3/4

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

3/4 - 7/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

1 - 1 1/8

SB02S03BH

SB04S04BH

SB04S06BH

SB04S08BH

SB04S10BH

SB04S12BH

SB04S14BH

SB08S06BH

SB08S08BH

SB08S10BH

SB08S12BH

SB08S14BH

SB12S06BH

SB12S08BH

SB12S10BH

SB12S12BH

SB12S14BH

SB12S16BH

SB22S08BH

SB22S10BH

SB22S12BH

SB22S14BH

SB22S16BH

SB22S18BH

SB30S20BH

SB30S24BH

DB08D04BH

DB08D06BH

DB12D06BH

DB12D08BH

DB12D10BH

DB12D12BH

DB12D14BH

DB15D06BH

DB15D08BH

DB15D10BH

DB15D12BH

DB15D14BH

DB22D08BH

DB22D10BH

DB22D12BH

DB22D14BH

6

15

18

22

34

39

41

29

32

40

46

58

42

53

66

75

92

119

102

125

131

149

178

214

341

461

26

34

50

54

61

81

104

61

82

94

123

150

132

171

173

201

3

4

6

8

10

12

14

6

8

10

12

14

6

8

10

12

14

16

8

10

12

14

16

18

20

24

4

6

6

8

10

12

14

6

8

10

12

14

8

10

12

14

2

4

4

4

4

4

4

8

8

8

8

8

12

12

12

12

12

12

22

22

22

22

22

22

30

30

8

8

12

12

12

12

12

15

15

15

15

15

22

22

22

22

SB02S03BS

SB04S04BS

SB04S06BS

SB04S08BS

SB04S10BS

SB04S12BS

SB04S14BS

SB08S06BS

SB08S08BS

SB08S10BS

SB08S12BS

SB08S14BS

SB12S06BS

SB12S08BS

SB12S10BS

SB12S12BS

SB12S14BS

SB12S16BS

SB22S08BS

SB22S10BS

SB22S12BS

SB22S14BS

SB22S16BS

SB22S18BS

SB30S20BS

SB30S24BS

DB08D04BS

DB08D06BS

DB12D06BS

DB12D08BS

DB12D10BS

DB12D12BS

DB12D14BS

DB15D06BS

DB15D08BS

DB15D10BS

DB15D12BS

DB15D14BS

DB22D08BS

DB22D10BS

DB22D12BS

DB22D14BS

6

15

18

22

34

39

41

29

32

40

46

58

42

53

66

75

92

119

102

125

131

149

178

214

341

461

26

34

50

54

61

81

104

61

82

94

123

150

132

171

173

201

3

4

6

8

10

12

14

6

8

10

12

14

6

8

10

12

14

16

8

10

12

14

16

18

20

24

4

6

6

8

10

12

14

6

8

10

12

14

8

10

12

14

Block w/ Swivel Shackle

SheaveO.D. (in.)

Weight(lb)

Part #

Snatch blocks are one of the most widely used general purpose blocks available. Over 235 models of Johnson single and double sheave snatch blocks are available. Johnson snatch blocks have a convenient side opening feature making it easy to thread the block without removing any fi ttings from the end of the wire rope. Stren-Flex® also offers a full line of mobile crane blocks, overhaul balls, swivels, hooks, and sheaves.

Sing

le S

heav

eTw

o Sh

eave

Single Sheave w/ Hook

Single Sheave w/ Shackle

Two Sheave w/ Hook

Two Sheave w/ Shackle

stren-fl ex.com 17

CARBON CHAIN G43, G70

Grade 43 High Test Chain*A higher strength carbon steel chain, Grade 43 high test chain provides an increased strength to weight ratio in comparison to Grade 30 chain. Grade 43 chain is often used in applications involving logging, construction, load binding and load securement.

Chain Size(in.)

Chain Size(in.)

Standard per foot (available in chain pails and drums)

Standard per foot (available in chain pails and drums)

Standard Drum(ft)

Standard Drum(ft)

Max. Weightper 100 ft. (lb)

Max. Weightper 100 ft. (lb)

1/4

5/16

3/8

7/16

1/2

5/8

3/4

7/8

1

1/4

5/16

3/8

7/16

1/2

2,600

3,900

5,400

7,200

9,200

13,000

20,200

24,500

34,100

3,150

4,700

6,600

8,750

11,300

Domestic Part #

Domestic Part #

Working Load Limit (lb)

Working Load Limit (lb)

678141FT

678142FT

678143FT

678144FT

678145FT

678146FT

678147FT

678148FT

678149FT

678531FT

678532FT

678533FT

678534FT

678535FT

800

550

400

300

200

150

100

80

60

800

550

400

300

200

60

98

133

204

227

357

606

776

904

71

100

156

204

259

Size(in. x ft.)

Grade 43 Grade 70Part #

(Welded w/ eye grab hooks)

Part # (Welded w/ eye

grab hooks)

Part # (Mechanical w/

clevis hook)

Part # (Mechanical w/

clevis hook)5/16 x 20

3/8 x 20

1/2 x 20

3,900

5,400

9,200

4,700

6,600

11,300

BC052043W

BC062043W

BC082043W

BC052070W

BC062070W

BC082070W

BC052043C

BC062043C

BC082043C

BC052070C

BC062070C

BC082070C

Working Load Limit

(lb)

Working Load Limit

(lb)

Grade 70 Transport or Binding Chain*Load ratings for Grade 70 chain averages 20% higher than Grade 43 chain, so a smaller size chain can be used for many jobs. Advantages include less weight, easier handling and more convenient storage. Higher strength makes Grade 70 ideal for truckers, loggers and highway crews for applications involvingtowing, hauling, lashing and trawling.

GRADE 43 GRADE 70

Grade 43 & Grade 70 Binder Chain AssembliesStren-Flex® Grade 43 & 70 binder assemblies are used by truckers, contractors, farmers and anyone dragging, binding or securing an object or objects. Binder chain assemblies can be made by welded or mechanical connections, in any length desired. Standard sizes are shown below.

* Grade 43 and 70 chain is not to be used for overhead lifting.

stren-fl ex.com 18

CARBON CHAIN ATTACHMENTS: G43, G70

Grade 43 Clevis Grab Hook (Zinc)

Grade 43 Clevis Slip Hook (Zinc)

Size(in.)

Size(in.)

Size(in.)

Working Load Limit (lb)

Working Load Limit (lb)

Working Load Limit (lb)

DomesticPart #

DomesticPart #

DomesticPart #

W

W

W

D

D

D

H

H

H

L

L

L

R

R

R

P

P

P

Weight (lb)

Weight (lb)

Weight (lb)

1/45/163/87/161/2

1/45/163/87/161/2

5/163/8

0.360.420.500.580.66

0.360.420.500.580.61

0.420.50

2.052.412.943.253.70

2.332.720.861.021.12

2.482.95

0.360.440.520.600.67

0.720.770.861.021.12

0.450.51

3.003.564.204.945.20

2.274.134.815.566.31

3.534.10

2,6003,9005,4007,2009,200

2,6003,9005,4007,2009,200

4,7006,600

6119361293613936149361593

6617366273663736647366573

6227362373

Dimensions (in.)

Dimensions (in.)

Dimensions (in.)

1.571.982.232.942.93

2.322.563.043.504.15

1.992.35

0.310.380.440.500.55

0.310.380.440.500.55

0.380.44

0.370.631.101.602.42

0.350.631.021.562.27

0.751.10

Grade 70 Clevis Grab Hook

Size(in.)

Working Load Limit (lb)

DomesticPart # W D H L R P

Weight(lb)

5/163/8

5/163/8

0.380.45

0.380.45

3.253.87

3.253.87

0.941.00

1.061.24

4.625.42

4.625.42

4,7006,600

4,7006,600

6905AWL6906AWL

M6905AM6906A

Dimensions (in.)

2.913.39

2.913.39

0.390.49

0.390.49

0.961.66

0.751.25

Grade 70 Clevis Slip Hook

Without Latch

With Latch

• Heat treated pins• Hooks are heat treated and tempered• Designs' ultimate strength equals 3 times working load limit, matching NACM specifi cations

• Hook embossed with trace code providing traceability through manufacturing and testing process to heat of steel• Not to be used for overhead lifting

• Heat treated pins• Hooks are heat treated and tempered• Designs' ultimate strength equals 3 times working load limit, matching NACM specifi cations

• Hook embossed with trace code providing traceability through manufacturing and testing process to heat of steel• Not to be used for overhead lifting

• Meets ASTM & NACM standards• Designed specifi cally for transport grade 70 chain• 4:1 design factor

• Yellow chromate fi nish• Not recommended for overhead lifting

• Meets ASTM & NACM standards• Designed specifi cally for transport grade 70 chain• 4:1 design factor

• Hook embossed with trace code providing traceability throughout the manufacturing and testing process to heat of steel

P

P

W

W

H

H

D

D

L

L

R

R

P

P

R

W

W

H

H

D

D

L

L

R

stren-fl ex.com 19

LOAD BINDERS

Lever Type Load Binder• All components are forged, no cast parts• Forged binders are lighter and stronger than cast binders• Under equal force a forged handle will yield and bend while a cast handle may break

Part #Working

Load Limit(lb)

Handle Take Up

(in.)Handle Length

(in.)Weight

(lb)G70G43

Size (in.)

1/4

3/8

1/2

3/8

1/4

3/8

1/2

3/8

1/2

-

5/16

3/8

3/8

3/16

5/16

3/8

5/16

3/8

48304

48305

48406

48769

DB-1

DB-2

DB-3

IMLB05-06

IMLB06-08

2,600

5,400

9,200

7,100

2,600

5,400

9,200

5,400

9,200

3.75

4.50

4.75

4.50

3.75

4.50

4.50

3.70

4.30

11.25

16.12

16.62

16.62

11.75

16.00

18.00

15.50

17.25

3.0

8.1

10.6

8.1

4

8.8

13

8.4

12.2

Part #Working

Load Limit (lb)

End Fittings Take Up(in.)

Handle Length (in.)

Weight(lb)G70G43

Size (in.)

3/8

1/2

5/8

3/8

1/2

5/8

3/8

1/2

5/16

3/8

1/2

5/16

3/8

1/2

5/16

3/8

48365

48366

48367

DR-1

DR-2

DR-3

IMRB05-06

IMRB06-08

Hook/Hook

Hook/Hook

Hook/Hook

Hook/Hook

Hook/Hook

Hook/Hook

Hook/Hook

Hook/Hook

5,400

9,200

13,000

6,600

9,200

13,000

5,400

9,200

8.00

8.00

8.00

8.00

8.00

8.00

8.00

8.00

14.00

14.00

14.00

15.50

15.50

15.50

15.00

15.00

12

13

16

12

14

15

10.5

11.7

Ratchet Type Load Binder• Each ratchet component is forged from pure alloy steel• Handle is designed loose using self-locking one-way bolt allowing easy removal of unwanted debris such as mud, snow or ice• Proof tested to 50% of the minimum breaking strength• Gears are permanently welded to the barrel

Removable Handle Load Binder• Removing handle provides greater load security by making it less likely for the load or the load binder to be stolen• Reduces overall weight and cost as only one handle is needed

Part # TypeWorking

Load Limit(lb)

HandleTake Up

(in.)Handle Length

(in.)Weight

(lb)G70G43

Size (in.)

3/8

1/2

-

3/8

1/2

-

5/16

3/8

-

5/16

3/8

-

48565

46566

46565H

DR-1-B

DR-X15-B

DR-RH

Body

Body

Handle

Body

Body

Handle

5,400

9,200

-

6,600

15,000*

-

8.00

8.00

-

8.00

8.00

-

-

-

14

-

-

17.25

7.4

11.7

4.3

8

10

3

CM

CM

CM

Durabilt

Durabilt

Durabilt

Import**

Import**

* Ultimate load is 3.5 times WLL in lieu of 4.** Import models specifi cations and dimensions may vary.

A

B

C

A

B

C

stren-fl ex.com 20

ALLOY CHAIN: G80, G100

Grade 80: CM Herc-Alloy 800 Chain• Meets or exceeds many national and international standards• Certifi cation included in every drum• 100% Proof Tested• Suitable for overhead lifting

Grade 100: CM Herc-Alloy 1000 Chain• Meets or exceeds many national and international standards• 25% higher working load limit when compared to Grade 80• Environmentally friendly gray coating for distinct appearance, ease of identifi cation• Certifi cation included with every drum• 100% Proof Tested• Suitable for overhead lifting

Chain Size(in.)

Chain Size(in.)

Nominal Chain Dimensions (in.)

Nominal Chain Dimensions (in.)

Inside LengthB

Inside LengthB

Material Dia.A

Material Dia.A

Inside WidthC

Inside WidthC

Chain Weight(lb/ft)

Chain Weight(lb/ft)

Approx. No. of Links

(per ft)

Approx. No. of Links

(per ft)

Standard Drum(ft)

Standard Drum(ft)

Drum Weight (lb)

Drum Weight (lb)

7/32

9/32

5/16

3/8

1/2

5/8

3/4

7/8

1

1-1/4

7/32

9/32

3/8

1/2

5/8

3/4

2,100

3,500

4,500

7,100

12,000

18,100

28,300

34,200

47,700

72,300

2,700

4,300

8,800

15,000

22,600

35,300

Part #

Part #

Working Load Limit

(lb)

Working Load Limit

(lb)

607020

607028

607031

607037

607050

607062

607075

607087

607101

607128

607321

607328

607339

607351

607363

607378

0.218

0.281

0.315

0.394

0.512

0.630

0.787

0.875

1.000

1.260

0.218

0.281

0.394

0.512

0.630

0.787

0.676

0.883

1.019

1.247

1.440

1.777

2.234

2.250

3.070

3.250

0.676

0.883

1.247

1.559

1.916

2.397

0.312

0.395

0.455

0.574

0.734

0.855

1.070

1.137

1.490

1.656

0.312

0.395

0.574

0.734

0.855

1.070

0.44

0.73

0.91

1.44

2.55

3.82

5.95

7.76

9.39

15.71

0.44

0.73

1.44

2.46

3.70

5.80

17.8

13.6

11.8

9.6

8.3

6.8

5.4

5.3

3.9

3.7

17.8

13.6

9.6

7.7

6.3

5.0

800

500

n/a

500

300

200

100

100

100

90

800

500

500

300

200

100

354

365

n/a

719

765

765

596

776

939

1,414

354

365

720

738

740

577

90˚60˚ 45˚ 30˚ 60˚ 45˚ 30˚

stren-fl ex.com 21

ALLOY CHAIN SLINGSHow to order chain slings:1. Grade 80 or 100 Chain2. Type of sling3. Chain size (in.)4. Reach (Length from bearing point to bearing point)

PART NUMBERING SYSTEM:

Chain Size(in.)

7/32

9/32

5/16

3/8

1/2

5/8

3/4

7/8

1

1-1/4

7/32

9/32

3/8

1/2

5/8

3/4

90˚ 45˚45˚ 30˚30˚

Working Load Limit for Angles Available (lb)

60˚60˚

2,100

3,500

4,500

7,100

12,000

18,100

28,300

34,200

47,700

72,300

2,700

4,300

8,800

15,000

22,600

35,300

3,600

6,100

7,800

12,300

20,800

31,300

49,000

59,200

82,600

125,200

4,700

7,400

15,200

26,000

39,100

61,100

3,000

4,900

6,400

10,000

17,000

25,600

40,000

48,400

67,400

102,200

3,800

6,100

12,400

21,200

32,000

49,900

2,100

3,500

4,500

7,100

12,000

18,100

28,300

34,200

47,700

72,300

2,700

4,300

8,800

15,000

22,600

35,300

5,500

9,100

11,700

18,400

31,200

47,000

73,500

88,900

123,900

187,800

7,000

11,200

22,900

39,000

58,700

91,700

4,400

7,400

9,500

15,100

25,500

38,400

60,000

72,500

101,200

153,400

5,700

9,100

18,700

31,800

47,900

74,900

3,200

5,200

6,800

10,600

18,000

27,100

42,400

51,300

71,500

108,400

4,000

6,400

13,200

22,500

33,900

53,000

SINGLE (1 LEG) DOUBLE (2 LEGS) TRIPLE (3 LEGS) & QUAD (4 LEGS)*

Gra

de 8

0G

rade

100

* Quad leg slings do not typically sustain the load evenly on each of its four legs. Therefore, the maximum working load limits are set the same as triple leg slings.

Type SOSSling Hook

Type SOGGrab Hook

Type SOFFoundry Hook

Type SOLLodelok Hook

AdjustableStyle A

AdjustableStyle B

D O G A - 10 04Number of LegsS = SingleD = DoubleT = TripleQ = QuadC = Choker

Master LinkO = Oblong

Types of HooksS = Sling HookG = Grab HookF = Foundry HookL = Lodelok Hook

StyleBlank = Standard A = Style A AdjustableB = Style B Adjustable

Reach3' & up

Size35 = 7/32"45 = 9/32"5 = 5/16"6 = 3/8"8 = 1/2"

10 = 5/8"12 = 3/4"14 = 7/8"16 = 1"20 = 1-1/4"

Rea

ch

Rea

ch

Reac

h

Reac

h

A B

C

Flat

HL

R R

P

D

G G

LH

M

M

D

P

O

I

I

B

N

G

K

D

E

P

MO

LH

S

stren-fl ex.com 22

ALLOY CHAIN ATTACHMENTS: G80

Clevlok Sling Hook• Available with and without a latch• Quench and tempered alloy steel• CM's clevlok head design• 100% proof tested• Fatigue rated• Replacement pin and latch kit available

Eye Sling Hook• Available with and without a latch• Quench and tempered alloy steel• 100% proof tested• Fatigue rated• Replacement latch kit available

Size(in.)

Size(in.)

Working Load Limit(lb)

Working Load Limit

(lb)

Latch KitPart #

Latch KitPart #

Weight w/o latch

(lb)

Weight w/o latch

(lb)

Hook Part #

Hook Part #

D

B

G

D

H

E

I

G

P

L

R

M N O P S

L

H

M

I

O

K

9/323/81/25/83/4

7/329/323/81/25/83/47/811-1/4

595523595525595528595529595530

595461595523595525595528595529595530595532595533595535

3.504.345.506.287.83

-1.632.062.633.063.503.884.315.31

5.166.678.009.69

11.69

3.313.504.335.506.347.838.599.59

11.56

0.330.450.590.750.88

1.441.501.882.252.633.003.384.004.66

0.730.951.171.441.69

4.305.256.648.169.66

11.3812.7214.2317.00

1.211.451.752.192.56

0.750.750.941.131.311.501.691.882.31

3.444.535.276.087.34

3.063.754.785.696.507.818.759.88

11.50

1.251.191.441.782.032.502.783.133.88

1.001.201.451.942.382.833.223.554.25

0.861.051.281.662.192.512.843.093.89

1.111.061.311.631.752.192.382.883.41

1.202.304.338.10

12.70

0.661.101.904.307.30

12.5018.1022.6047.00

0.360.510.630.750.91

0.380.440.560.750.881.001.091.221.50

1.191.471.782.032.50

0.780.730.951.171.441.691.942.142.62

0.811.091.281.441.75

1.251.592.192.562.633.443.884.254.64

3,5007,100

12,00018,10028,300

2,1003,5007,100

12,00018,10028,30034,20047,70072,300

658338658339658340658341658342

458544458722458725458728458729458730458732458733458735

Dimensions (in.)

Dimensions (in.)

Master Link with Flats• Designed to accept HA 800 Chain, Wire Rope and Synthetic Webbing• Use with mechanical and welded chain assemblies• Sizes up to 1-1/4" available with fl ats to accomodate Omega link

Nominal Dim. (in.)Size(in.)

Working Load Limit

(lb)Part # Material Dia.

AInside Length

BInside Width

CWeight

(lb)Single

(in.)Double

(in.)

7/161/25/83/47/811-1/41-1/21-3/422-1/42-1/2

0.4370.5120.6250.7500.8751.0001.2501.5001.7502.0002.2502.500

0.500.801.342.363.605.209.60

16.2025.1038.4054.6074.90

7/32 & 9/32-

3/81/2

-5/8

3/4 & 7/81-

1-1/4--

-7/329/32

3/8-

1/25/83/47/8

1-

1-1/4

4,2005,7509,000

14,20017,30026,50037,40053,00072,15094,200

119,200147,150

4.1304.8385.2926.6117.3507.5269.261

11.02512.86314.70016.53818.375

ML040ML050ML063ML075ML087ML100ML125ML150ML175ML200ML225ML250

2.2942.6882.9773.7194.1354.3015.2926.3007.3508.4009.450

10.500

Type & Size of Chain Sling

• 100% proof tested• Extra wide body for Wire Rope applications

B

H

GKE

P

D

M

L

I

H B

L

N R (Spher.)

KE

D (Ref)

O

G (Ref)M

I

T

G

P

K

D

E

L

M

HB

stren-fl ex.com 23

ALLOY CHAIN ATTACHMENTS: G80

Clevlok Cradle Grab Hook• CM's unique cradle grab design• Quench and tempered alloy steel• Fatigue rated• Replacement pin available

Eye Cradle Grab Hook• CM's unique cradle grab design• Quench and tempered alloy steel• 100% proof tested• Fatigue rated

Eye Foundry Hook• Throat opening up to 6"• Quench and tempered alloy steel• Fatigue rated to Grade 80 specifi cations

Size(in.)

Size(in.)

Size(in.)

Part #

Part #

Part #

Working Load Limit

(lb)

Working Load Limit

(lb)

Working Load Limit

(lb)

Weight (lb)

Weight(lb)

Weight(lb)

B

B

B

D

D

D

E

E

E

G

G

G

M

L

L

P T

M

M N O

P

R

H

H

H

K

I

I

L

K

K

9/323/81/25/83/4

7/329/323/81/25/83/47/811-1/4

9/323/81/25/83/47/811-1/4

1.311.812.162.693.09

1.191.381.782.282.753.193.754.315.38

1.562.002.503.003.504.004.505.13

1.782.563.254.084.91

1.751.912.783.634.415.235.697.008.25

4.755.756.757.819.13

10.1411.1312.84

.359

.469

.594

.750

.875

0.360.360.470.590.750.881.001.191.50

2.503.003.504.004.505.005.506.00

3.004.085.276.537.88

2.693.704.816.197.628.999.63

12.4415.56

6.457.889.3810.9712.8114.2315.8418.03

1.632.112.883.564.25

0.630.630.781.031.251.441.751.882.25

0.630.751.001.131.501.752.132.38

0.721.061.281.591.88

1.191.752.132.503.13

1.632.573.284.225.066.256.508.09

10.50

4.755.756.888.069.25

10.3811.5612.88

2.503.003.504.004.505.005.506.00

1.231.501.752.032.562.783.033.81

0.70.761.041.511.801.882.123.123.50

0.250.310.380.440.500.560.620.75

0.441.182.704.60

10.24

0.350.551.062.005.409.00

10.4020.9040.00

2.44.57.1

11.620.026.036.858.4

0.330.450.590.750.88

0.380.380.500.630.750.881.001.221.56

0.470.630.750.881.001.131.251.38

0.981.411.882.382.84

1.191.061.381.812.132.883.003.882.50

1.001.271.501.812.202.252.593.17

0.360.510.630.750.91

0.961.041.491.982.393.503.754.315.50

1.561.882.222.633.003.383.754.25

659222659225659228659229659430

559318559325559337559350559362559575559387559100559124

474498474499474500474501474502474503474504474505

3,5007,100

12,00018,10028,300

2,1003,5007,100

12,00018,10028,30034,20047,70072,300

3,5007,100

12,00018,10028,30034,20047,70072,300

Dimensions (in.)

Dimensions (in.)

Dimensions (in.)

H J

K

M

GR

L

P

D

AG H

JED

F

B

C

stren-fl ex.com 24

ALLOY CHAIN ATTACHMENTS: G80

Clevlok Style Lodelok Hook• High cycling, long life spring• Factory replaceable pins• "I" beam construction for greater strength• 100% proof tested• Fatigue rated to grade 100 specifi cations

Eye Style Lodelok Hook• Large eye design for use with chain, wire rope and synthetic material• Factory replaceable pins• 100% proof tested• Fatigue rated to grade 100 specifi cations• For welded 7/32" Chain Sling use 9/32" Eye Lodelok Hook

Size(in.)

Size(in.)

Working Load Limit

(lb)

Working Load Limit

(lb)

Product Code

Product Code

Replace Latch Kit

Part #

Replace Latch Kit

Part #

D

A

G

B

H

C

J

D

K

E

L

F min

M

G

P

H

R

J

Weight(lb)

Weight(lb)

9/32

3/8

1/2

5/8

9/32

3/8

1/2

5/8

3.89

5.03

6.68

8.04

2.00

2.50

3.44

3.94

6.37

8.20

10.07

11.62

1.31

1.78

2.38

2.62

0.35

0.47

0.59

0.71

5.43

7.41

9.38

10.71

1.00

1.16

1.50

1.74

1.00

1.25

1.75

2.00

4,300

8,800

15,000

22,600

4,300

8,800

15,000

22,600

616005

616010

616015

616020

626005

626010

626015

626020

656005

656010

656015

656020

656005

656010

656015

656020

Dimensions (in.)

Dimensions (in.)

1.19

1.25

1.63

1.88

3.89

5.03

6.68

8.04

0.36

0.51

0.63

0.75

1.563

2.250

2.813

3.125

1.56

2.25

2.81

3.19

1.47

2.00

2.59

2.92

1.00

1.25

1.75

2.00

0.63

0.75

1.00

1.25

4.68

6.11

7.25

8.36

1.19

1.25

1.63

1.88

2.62

4.93

9.32

14.70

2.64

4.86

10.46

16.52

Other Attachments Available:

Swivel Style Lode-lok Hook

Sorting Hook Sorting Hookw/ Handle

"S" HookPlate Hook Specialty Hooks

B

FF

G G

EE

DHA

Sling Width

Fabric Length

Usable Length for Choker Hitch

Overall Sling Length

Usable Length for Basket Hitch

stren-fl ex.com 25

WIRE MESH SLINGS

Wire Mesh Sling Inspection CriteriaMetal mesh slings shall be immediately removed from service if any of the following conditions are present:• Twist or stretch of either handle.• A 15% reduction of the original cross sectional area of metal at any point around the handle eye.• Lack of fl exibility caused by damage to the mesh fabric.• 25% reduction in mesh wire diameter due to abrasion and 15% reduction in mesh wire diameter due to corrosion.• Broken welds or joints on the body or edge of the sling.• Any broken wires.

Note: All Stren-Flex® wire mesh slings —whether new or repaired— are tested and certifi ed before delivery to the customer.

A Width (Nom.)

Sling Width (in.)

Hook Size (ton)

Approx. Weight of

3' SlingB C

Vertical

D E

Choker

F HG-35

10 GaugeG-43

12 GaugeG-59

14 GaugeG

Vertical Basket

DD

2

3

4

6

8

10

12

14

16

18

20

2

3

4

6

8

10

12

14

16

18

20

1/2

3/4

3/4

1

1-1/4

1

1

1-1/4

1-1/4

2

2

1,600

3,000

4,400

6,600

8,800

11,000

13,200

15,400

17,600

19,800

22,000

2-3/4

3-1/2

3-1/2

4

5-1/2

5

5

5

5

5

5

1-3/4

2-1/2

2-1/2

2-3/4

4

3-1/2

3-1/2

3-1/2

3-1/2

4

4

3,200

6,000

8,800

13,200

17,600

22,000

26,400

30,800

35,200

39,600

44,000

4

5-1/4

6-1/4

8-1/2

11-1/4

12-3/4

14-3/4

17

19

21-1/4

23-1/4

3-3/4

5

5

6

8-1/2

7-1/2

7-1/2

7-3/4

7-3/4

11

11-1/4

5

10

10

15

25

25

30

30

30

30

30

5

8

10

15

20

26

33

37

44

51

58

1.25

1.88

2.50

3.88

5.13

3.38

7.63

8.88

10.13

11.38

12.75

1.13

1.75

2.25

3.38

4.50

5.63

6.75

7.88

9

10.13

11.25

.75

1.13

1.50

2.25

3.0

3.75

4.50

5.25

6

6.75

7.50

4

5-1/4

5-1/2

6-1/2

8-3/4

7-3/4

8

8-1/4

8-1/4

8-1/2

8-1/2

2

3

4

6

8

10-1/4

12-1/4

14-1/4

16-1/4

18

20

6

7-1/2

7-3/4

9

12

10-3/4

11-1/4

12

12-1/2

13-1/4

14

1,600

3,000

4,400

6,600

8,800

11,000

13,200

15,400

17,600

19,800

22,000

Length (in.)

Capacity

Fabric lbs/ft of Length

NOTE: Accommodates most hooks to listed size. Standard tolerance + or - 1/2”.Type 1 pictured above.Type 2 is fabricated with a male fi tting each end and is used exclusively in a basket hitch.

Wire Mesh Slings combine the fl exibility, choking capabilities and stability of a synthetic sling with the abrasion and heat resistant characteristics of a chain sling. Wire Mesh Slings are available in three gauges of wire thickness and widths ranging from 20” through 2”. Whether new or repaired, every sling is stamped with serial number and working capacity and is proof tested and certifi ed. Stren-Flex® fabricates and repairs all sizes of chain mesh slings.

Ordering Specifi cations for Wire Mesh Slings:• Gage of wire mesh• Type of sling — end fi ttings• Width of sling — width of wire mesh• Length of sling

HEAVY DUTY MESH (10 GAGE)The most popular size of mesh. Tough against abrasion and sharp edges. Grade 35 - 1/2” Thick

stren-fl ex.com 26

OSHA & ASME REFERENCE

Wire Rope SlingsOSHA 29 CFR 1910.1841) Do not exceed working load limit (WLL).2) Min. of 10 dia. between sleeves/splices.3) Consult manufacturer for use of fi ber core slings in excess of 200°F or steel core slings below -60°F or above 400°F.4) Welded attachments must be proof tested by manufacturer prior to initial use.5) Remove if any of the following is present: • Broken wires ≥ 10/lay, 5 in 1 strand/lay • 1/3 wear of outside wires • Kinks, crushing, birdcaging, corrosion, distortion of wire rope structure or damaged end fi ttings • Evidence of heat damage • Hooks with 15% spread or 10° twist

ASME B30.91) Eye shall not be formed using knots.2) Use wire rope clips only in temporary situation where prefabrication is not possible.3) Each sling shall be visually inspected by handler before each use.4) Remove if any of the following is present: • Broken wires for multi-part slings: Less than 8-part and Cable Laid ≥ 20/lay, 20/braid/lay, 1 strand/sling 8-part or more ≥ 40/lay, 40/braid/lay, 1 strand/sling • Core damage, severe abrasion

Alloy Chain SlingsOSHA 29 CFR 1910.1841) Do not exceed working load limit. (WLL)2) Slings shall be permanently marked with size, grade, rated capacity and reach.3) Chain slings shall not be used in excess of the rated capacity of the weakest component.4) Slings shall be thoroughly inspected at intervals no greater than once every 12 months. Records of such inspections must be kept on fi le.5) Makeshift links or fasteners made from bolts, rods or other materials shall not be used.6) Worn or damaged slings or attachments shall not be used until repaired.7) Mechanical coupling or low carbon steel repair links shall not be used to repair broken lengths of chain.8) Remove if any of the following is present: • Heated above 1000°F • Cracked or deformed master links, couplings, hooks or other components • Hooks are cracked and have been opened more than 15% or twisted more than 10° from plane of unbent hook • Chain wear beyond tolerance

ASME B30.91) These regulations apply only to slings made from Grade 80 or higher alloy chain manufactured and tested in accordance with National Association of Chain Mfrs.2) Prior to use, welded components of new slings shall be proof tested to (2xWLL).3) Repaired slings shall be permanently marked with name of repairing agency.4) Latches on hooks should seat properly, rotate freely, and show no permanent distortion.5) Slings should be long enough so that the working load limit is adequate when the angle of the legs is taken into consideration.6) Check chain and attachments for wear, nicks, cracks, breaks, gouges, stretch, bends, weld splatter, discoloration from excessive temperature, and stretched throat openings on hooks.

NOTES: Legal standard pertaining to slings, wire ropes, and below the hook devices are specifi cally and literally enforced by OSHA when the standard has a penalty attached. On most occasions the law uses the word “shall” in the reference. Sometimes the word “should” is used in the place of “shall”. The word “shall” requires compliance with the action or inaction required. The word “should” only recommends compliance. The difference is that absent some gross negligence or other aggravating circumstance, someone would not be punished under the law for failing to do some action suggested by the word “should”. Failure to perform an action directed by the word “shall” does give rise to the defi nite possibility of a legal penalty, and is a violation of the law.

Quick Reference Guide(OSHA 29 CFR 1910.184 & ASME B30.9)

stren-fl ex.com 27

INSPECTION REFERENCE

Wire Rope Sling Removal CriteriaWire rope, and wire rope slings should be removed from service upon observation of any of the following conditions: 1) Ten randomly distributed broken wires in one rope lay, or fi ve broken wires in one strand of one rope lay. 2) Kinking, crushing, birdcaging, core damage or any other damage resulting in distortion of the wire rope structure. 3) Evidence of heat damage. 4) Cracked, deformed, or worn end attachments. 5) Hooks that have been opened more than 15% of the normal throat opening measured at the narrowest point or twisted more than 10° from the plane of an unbent hook. 6) Missing or illegible sling identifi cation. 7) Corrosion of rope or end attachments. 8) Eye/Eye slings: Min. of 10 times the rope diameter between sleeves. 9) Grommet slings: Min. of 96 times the rope diameter.10) Extensive wear (greater than 1/3 of outside wires).

Alloy Chain Slings Removal Criteria 1) Missing or illegible sling identifi cation. 2) Bent, twisted, cracked, stretched or otherwise deformed components. 3) Components with severe wear, nicks or gouges. 4) Severe corrosion or pitting. 5) Improperly functioning mechanical components. 6) Stretched or bent links. 7) Broken or non-functional latches (if present.) 8) Hook spread or twist. 9) Makeshift links or fasteners.10) Broken chain repaired with low carbon links.11) Heat damage, weld spatter (See table)

Temperature(°F)

Reduction in WLL During Exposure

Permanent Reduction in WLL after Exposure

-40 - 400

400 - 500

500 - 600

600 - 700

700 - 800

800 - 900

900 - 1000

>1000

None

5%

10%

20%

25%

35%

40%

None

None

None

None

10%

25%

30%

Remove from service

10. Low carbon link in sling body

1. Missing identifi cation

2. Bent links 4. Severe corrosion 6. Stretched links 8. Hook spread or twist

3. Severe wear

1. Broken wires

2. Crushing, core damage

3. Heat damage

8. Insuffi cient space between sleeves

6. Missing identifi cation

9. Length less than 96 times diameter

10. Extensive outer wire wear

4. Deformed end fi ttings

5. Stretched and twisted hooks

7. Corrosion, rust

EFFECT OF HEAT ON CHAIN

STREN-FLEX®

ph: 877.STREN-FLEX (877.787.3635)© 2009 Stren-Flex | printed in USA