wcdma ran13 parameter mapping(ericsson w10,nsn ru10, ru20, alu ua5.1)

document.xls 文档密级：

04/17/2023 华为机密，未经许可不得扩散第1页，共66页

1

2

3

Item



Draft was completed.

Description

1、Note:.sheet E/// Whether TMA used or not, PCPICHPower and MaxTxPower use the same function.2、Line 38~39 and 54~55，Mapping with E///, TimeToTrig2D/TimeToTrig2F use Min（timeToTrigger2dEcno,timeToTrigger2dRscp）and Min（timeToTrigger2fEcno,timeToTrigger2fRscp）

1、Line 277~288 HSPA parameters added;2、Line 5: column W/AC HopiIdentifier monified to HopgIdentifier。3、Line 57~Line 68 "WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is 0, use the value -24. " is modified to "WCEL > the RtFmcsIdentifier value > the FMCG value > the GSMcauseCPICHEcNo valueIf the NSN value is 0, use the value -24. "4、Line 84: column Q,W,AC,AI modified to "Use the XXX Value".



V1.00 Huang Xiangrong 2011.07.30

v1.01 Huang Xiangrong 2011.08.12

v1.02

Huang Xiangrong

2011.10.25

Version Author Date Remarks



URFSTG00571 - Huawei WCDMA BSC6900V900R013 Vs Ericsson W10/NSN RU10/NSN RU20/AL UA5.1

1

2

3

For parameters for which this document does not provide mapping analysis, see the Baseline Parameter Values. Using other vendors' parameters values may not optimize Huawei network settings because Huawei algorithms are different from other vendors' algorithms. For values of Compressed Mode Start Threshold for Inter-Frequency, Compressed Mode End Threshold for Inter-Frequency, Compressed Mode Start Threshold for Inter-RAT, Compressed Mode End Threshold for Inter-RAT, and HCS, see the Guide to UMTS Swapping. For values for parameters realted to the multi-carrier policy, see the UMTS R12 Multi-Frequency Band and Multi-Carrier Performance Solution.

Notes about mapping:

Algorithm-related parameters for which this document does not provide mapping analysis, refer to Huawei baseline values.

Some of other vendors' values can be used directly while some values must be multiplied, divided, added, or subtracted before they can be used.

For values for network-related parameters for which this document has provided mapping analysis, refer to the actual values in the live network. For example, for the values for PCPICH Transmit Power and Max Transmit Power of Cell, check whether the (top of cabinet)TOC power or antenna power is used. Huawei uses the TOC power and therefore other vendors' values can be used they also use the TOC power. If other vendors do not use the TOC power, add the feeder loss.

Notes about priority definition:



Principle:1. The parameters related to cell reselction initiated by UEs in idle mode, idle mode-related timers, connected mode-related timers, power control, soft handovers, inter-frequency handovers, inter-RAT handovers, and state transition have a high mapping priority. Therefore, Huawei personnel must focus on these parameters during parameter mapping.2. Compared with the Huawei inter-RAT handover mechanism, the NSN inter-RAT handover mechanism triggers more inter-RAT handovers. For details, see the following description. Therefore, Huawei personnel must inform custoers that the number of inter-RAT handovers may decrease after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the NSN inter-RAT handover mechanism, Huawei personnel can raise the 2D or 2F threshold by 1 to 2 dB.The Ericsson inter-RAT handover mechanism is triggered by events while the Huawei inter-RAT handover mechanism is triggered by periodical measurement results. In this case, the Ericsson inter-RAT handover mechanism triggers less inter-RAT handovers than the Huanwei inter-RAT handover mechanism. This leads to decreased CS traffic in 3G cells and the increased number of inter-RAT handovers after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the Ericsson inter-RAT handover mechanism, Huawei personnel can lower the 2D or 2F threshold by 1 to 2 dB.

To find appropriate values for PCPICH Transmit Power and Max Transmit Power of Cell, first check whether some TMAs are used. To do this, check the value for ulGain. If the value is 0, no TMAs are used. Otherwise, some TMAs may be in useIf some TMAs are used, use the following formula to calculate values for the preceding two parameters:MaxTxPower (HUAWEI) = maximumTransmissionPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson) PCPICHPower (HUAWEI) = primaryCpichPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson)If no TMAs are used, use Ericsson vlaues since Ericsson also uses the TOC power.Notes:The ulGain parameter is a NodeB-level parameter and thefore dump documents can be obtained only on a PLMN basis. After this, all RNC and NodeB parameters can be obtained.The following figure shows a base station where a TMA is used:



Ericsson calculates the maximum transmit power of a radio link in the following way:For the RL Max DL TX power parameter, calculate the value for different sevices based on the following scripts and figure:Radio Connection Type Maximum DL Radio Link Rate MaxPower PS384/HS 3700 0 SRB 13.6 14800 0 AMR 12.2 15900 0 CS64 67700 32 PS64/64 70900 34 MultiRAB (CS64 + PS8/8) 76100 37 PS64/384 406900 48Note that parameter values in the preceding scripts are just examples, and therefore onsite personnel must check which values are used in Ericsson scripts and then calculate the value for RL Max DL TX power for different services.For example, the maximum downlink radio link rate is 67700 for the CS64 service. In addition, InterRate is set to 77600, interPwrMax is set to 38, MinimunRate is set to 15900, and minPwrMax is set to 0. Then, according to the following formula, the RL Max DL TX power parameter for this services must be set to 31.9:RL Max DL TX power = (interPwrMax-minPwrMax)/(InterRate - MinimunRate)x(Maximum DL Radio Link Rate - MinimunRate)

The NSN inter-RAT handover measurement mechanism operates in the following way:During the inter-RAT handover measurement procedure, the RNC determines whether to enable UEs to stop being in compressed mode after event 1E is reported based on the values for ISHOCancellation, ISHOClcauseCPICHEcNo, ISHOClcauseCPICHrscp, and MaxNumISHOClPerAS.For example, the RNC enables a UE to stop being in compressed mode after event 1E is reported when the following three conditions are met:1. MaxNumISHOClPerAS is set to 1 or a smaller value.2. ISHOCancellation is set to Enabled.3. ISHOClcauseCPICHEcNo is set to Enabled or ISHOClcauseCPICHrscp is set to Enabled.However, the Huawei algorithm neables a UE to stop being in compressed mode after event 2F is reported. Compared with the Huawei inter-RAT handover measurement mechanism, the NSN inter-RAT handover measurement mechanism triggers more inter-RAT handovers.



Cancellation of inter-system handover because of event 1EThe RNC stops inter-system measurements when event 1E occurs for at least one cellof the active set. Event 1E can be configured for the following measurements on thePrimary CPICH:• CPICH RSCP: received signal code power (RSCP)• CPICH Ec/No: received energy per chip divided by the power density in the band,that is CPICH RSCP/UTRA Carrier RSSIThe parameters ISHOClcauseCPICHEcNo and/or ISHOClcauseCPICHrscp indicatewhether inter-system measurement cancellation in the UE is enabled or not for situationswhen a primary CPICH (active set cell) increases beyond the absolute threshold(Event 1E).

Inter-System handover cancellation because of measurement event 1E can be performedonly when all of the following conditions are met:• The Inter-System Handover Cancellation feature is enabled by theISHOCancellation parameter.

• The ISHOClcauseCPICHEcNo or ISHOClcauseCPICHrscp parameter has beenset to ‘enabled’ for one or more cells in the active set.

• The number of inter-system cancellations that have been performed for the correspondingUE with the current active set is less than the value specified for theMaxNumISHOClPerAS parameter.

• Inter-System measurements were started in the UE because of event 1F (for CPICHEc/No or CPICH RSCP) triggered measurement report.• Event 1E triggered measurement report was received during inter-system measurementphase.



URFSTG00571 - Huawei WCDMA BSC6900V900R013 Vs Ericsson W10/NSN RU10/NSN RU20/AL UA5.1

For parameters for which this document does not provide mapping analysis, see the Baseline Parameter Values. Using other vendors' parameters values may not optimize Huawei network settings because Huawei algorithms are different from other vendors' algorithms. For values of Compressed Mode Start Threshold for Inter-Frequency, Compressed Mode End Threshold for Inter-Frequency, Compressed Mode Start Threshold for Inter-RAT, Compressed Mode End Threshold for Inter-RAT, and HCS, see the Guide to UMTS Swapping. For values for parameters realted to the multi-

UMTS R12 Multi-Frequency Band and Multi-Carrier Performance Solution.

Algorithm-related parameters for which this document does not provide mapping analysis, refer to

Some of other vendors' values can be used directly while some values must be multiplied, divided, added, or subtracted before they can be used.

For values for network-related parameters for which this document has provided mapping analysis, refer to the actual values in the live network. For example, for the values for PCPICH Transmit Power and Max Transmit Power of Cell, check whether the (top of cabinet)TOC power or antenna power is used. Huawei uses the TOC power and therefore other vendors' values can be used they also use the TOC power. If other vendors do not use the TOC power, add the



1. The parameters related to cell reselction initiated by UEs in idle mode, idle mode-related timers, connected mode-related timers, power control, soft handovers, inter-frequency handovers, inter-RAT handovers, and state transition have a high mapping priority. Therefore, Huawei

2. Compared with the Huawei inter-RAT handover mechanism, the NSN inter-RAT handover mechanism triggers more inter-RAT handovers. For details, see the following description. Therefore, Huawei personnel must inform custoers that the number of inter-RAT handovers may decrease after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the NSN inter-RAT handover mechanism, Huawei personnel can raise the 2D or 2F threshold by 1 to 2 dB.The Ericsson inter-RAT handover mechanism is triggered by events while the Huawei inter-RAT handover mechanism is triggered by periodical measurement results. In this case, the Ericsson inter-RAT handover mechanism triggers less inter-RAT handovers than the Huanwei inter-RAT handover mechanism. This leads to decreased CS traffic in 3G cells and the increased number of inter-RAT handovers after swapping. If customers request that the Huawei inter-RAT handover mechanism opearte in the same way as the Ericsson inter-RAT handover mechanism,

Max Transmit Power of Cell, first check whether some TMAs are used. To do . If the value is 0, no TMAs are used. Otherwise, some TMAs may be in use

If some TMAs are used, use the following formula to calculate values for the preceding two parameters:MaxTxPower (HUAWEI) = maximumTransmissionPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson) PCPICHPower (HUAWEI) = primaryCpichPower + dlAttenuation(ExternalTma) + dlAttenuation(AntFeederCable) (Ericsson)If no TMAs are used, use Ericsson vlaues since Ericsson also uses the TOC power.

The ulGain parameter is a NodeB-level parameter and thefore dump documents can be obtained only on a PLMN basis. After this, all RNC and



Ericsson calculates the maximum transmit power of a radio link in the following way: parameter, calculate the value for different sevices based on the following scripts and figure:

Radio Connection Type Maximum DL Radio Link Rate MaxPower

Note that parameter values in the preceding scripts are just examples, and therefore onsite personnel must check which values are used in for different services.

For example, the maximum downlink radio link rate is 67700 for the CS64 service. In addition, InterRate is set to 77600, interPwrMax is set to . Then, according to the following formula, the RL Max DL TX power parameter

RL Max DL TX power = (interPwrMax-minPwrMax)/(InterRate - MinimunRate)x(Maximum DL Radio Link Rate - MinimunRate)

The NSN inter-RAT handover measurement mechanism operates in the following way:During the inter-RAT handover measurement procedure, the RNC determines whether to enable UEs to stop being in compressed mode after

ISHOClcauseCPICHEcNo, ISHOClcauseCPICHrscp, and

For example, the RNC enables a UE to stop being in compressed mode after event 1E is reported when the following three conditions are met:

is set to Enabled.However, the Huawei algorithm neables a UE to stop being in compressed mode after event 2F is reported. Compared with the Huawei inter-RAT handover measurement mechanism, the NSN inter-RAT handover measurement mechanism triggers more inter-RAT handovers.



The RNC stops inter-system measurements when event 1E occurs for at least one cellof the active set. Event 1E can be configured for the following measurements on the

CPICH Ec/No: received energy per chip divided by the power density in the band,

The parameters ISHOClcauseCPICHEcNo and/or ISHOClcauseCPICHrscp indicatewhether inter-system measurement cancellation in the UE is enabled or not for situationswhen a primary CPICH (active set cell) increases beyond the absolute threshold

Inter-System handover cancellation because of measurement event 1E can be performed

The ISHOClcauseCPICHEcNo or ISHOClcauseCPICHrscp parameter has been

The number of inter-system cancellations that have been performed for the corresponding

Inter-System measurements were started in the UE because of event 1F (for CPICH

Event 1E triggered measurement report was received during inter-system measurement



NE Parameter Type

RNC CELL Inter RNC Cell Update

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL Access Class Restriction

















Cell-Level or RNC-Level

Intra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power ControlPhysical Channel ManagementPhysical Channel ManagementPhysical Channel ManagementIntra Node B Softer HandoverOpen Loop Power Control






RNC CELL

RNC CELL HSDPA Power Control

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

Admission ControlLoad Measurement

Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage

Inter-RAT Handover Based on Coverage



RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL None

RNC CELL None

RNC CELL

RNC CELL

RNC CELL







Inter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage

Inter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover

Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover



RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC RNC 3GPP Specifications

RNC RNC


RNC RNC











RNC CELL

Intra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power Control

Connection with TMA (Tower Mounted Amplifier)

System Information Broadcasting




RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL None

RNC CELL

RNC RNC

RNC RNC





RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

Intra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateInter RNC Soft HandoverDirect Signaling Connection Re-establishment (DSCR)Inter RNC Soft HandoverDirect Signaling Connection Re-establishment (DSCR)Intra Node B Softer Handover

Open Loop Power ControlInner Loop Power ControlPaging UE in Idle, CELL_PCH, URA_PCH State (Type 1)

Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on Coverage



RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC CELL



RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

Inter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell Update

Inter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover



RNC RNC

RNC RNC

RNC RNC

RNC RNC None

RNC RNC None

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL



RNC CELL

Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover

Intra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlOpen Loop Power ControlSystem Information BroadcastingSystem Information BroadcastingSystem Information BroadcastingOpen Loop Power Control

Intra RNC Cell UpdateInter RNC Cell Update



RNC CELL

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC None

RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL None

RNC CELL

RNC CELL




RNC CELL

RNC RNC

RNC RNC

Intra RNC Cell UpdateInter RNC Cell UpdateIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover

Intra Node B Softer HandoverIntra Node B Softer HandoverIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateMulti Frequency Band Networking ManagementIntra RNC Cell UpdateMulti Frequency Band Networking ManagementIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer HandoverIntra Node B Softer Handover

Intra Node B Softer HandoverIntra Node B Softer Handover

Inter-RAT Handover Based on CoverageHSDPA State TransitionHSUPA DCCCHSDPA State TransitionHSUPA DCCC



RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

HSDPA State TransitionHSUPA DCCC3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB Assignment3.4/6.8/13.6/27.2 kbit/s RRC Connection and RAB AssignmentUE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)

UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)UE State in Connected Mode (CELL-DCH, CELL-PCH, URA-PCH, CELL-FACH)Open Loop Power ControlAdmission Control

Open Loop Power ControlInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on CoverageInter Frequency Hard Handover Based on Coverage



RNC CELL

RNC CELL

RNC CELL

RNC CELL None

RNC CELL 3GPP Specifications

RNC CELL None

RNC CELL 3GPP Specifications

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC CELL

RNC RNC

RNC RNC

RNC RNC

RNC CELL

RNC CELL

RNC CELL

CELL HSUPA

CELL HSUPA

CELL HSUPA

CELL HSUPA

CELL HSUPA

Physical Channel ManagementPhysical Channel Management3GPP SpecificationsShared Network Support in Connected Mode

Intra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateIntra RNC Cell UpdateInter RNC Cell UpdateInter-RAT Handover Based on CoverageInter-RAT Handover Based on DL QoSInter-RAT Handover Based on CoverageInter-RAT Handover Based on CoverageHSDPA Introduction PackageHSDPA Mobility ManagementHSDPA Mobility ManagementHSDPA Mobility ManagementHSUPA Mobility ManagementInter Frequency Hard Handover Based on Coverage

Inter-RAT Handover Based on CoverageInter-RAT Handover Based on Coverage

RNC

RNC

RNC

RNC

RNC



CELL HSUPA

CELL HSUPA

CELL

HSUPA

CELL HSUPA

CELLHSUPA

CELL HSUPA

CELL HSUPA

RNC

RNC

RNC

RNC

RNC

RNC

RNC



Parameter ID Parameter Name Meaning

Qoffset1sn Qoffset1sn

Qrxlevmin Min RX Level

BCHPower BCH Transmit Power

MaxTxPower

NInsyncInd

NOutsyncInd

TRlFailure

CIO

PCPICHPower

CellReservedForOperatorUse

IsAccessClass0Barred
















Offset between the neighboring GSM cell and WCDMA cell.Minimum RX level of the GSM cell.Offset of the BCH transmit power from the PCPICH transmit power in a cell. For detailed

Max Transmit Power of Cell

Sum of the maximum transmit power of all DL channels in a cell. For detailed information of

Num of Continuous in Sync Ind

This parameter defines the times of successive in-sync indications required for the NodeB to

Num of Continuous Out of Sync Ind

This parameter defines the times of successive in-sync indications required for starting the

Radio Link Failure Timer Length

Radio link failure timer duration. When the radio link set is in the synchronized state, the

Cell Oriented Cell Individual Offset

This parameter works with the offset of neighboring cell-oriented Cell Individual Offset

PCPICH Transmit Power

TX power of the PCPICH in a cell. This parameter should be set based on the actual system

Cell reserved for operator use

Indicating whether the cell is reserved for operators. If the status of cell is NOT_BARRED,

Access class 0 barred indicator

Indicating whether the UE allocated with Access Class 0 can be allowed to initiate access to the

































IdleCellBarred

IdleIntraFreqReselection

IdleTbarred Time barred for SIB3

BackgroundNoise Background noise

HspaPower

PrdReportInterval

HystFor2D 2D Hysteresis

HystFor2F 2F Hysteresis

TimeToTrig2D Event 2D Trigger Delay

TimeToTrig2F Event 2F Trigger Delay

InterFreqCSThd2DEcN0

InterFreqCSThd2FEcN0

InterFreqR99PsThd2DEcN0

InterFreqHThd2DEcN0

InterFreqR99PsThd2FEcN0

InterFreqHThd2FEcN0

InterFreqCSThd2DRSCP

InterFreqCSThd2FRSCP

InterFreqR99PsThd2DRSCP

InterFreqHThd2DRSCP

InterFreqR99PsThd2FRSCP

InterFreqHThd2FRSCP

Hystfor2D 2D Hysteresis

Hystfor2F 2F Hysteresis

TrigTime2D

TrigTime2F

TrigTime3A

InterRATCSThd2DEcN0

Cell barred indicator for SIB3

Indicating whether the UE in idle mode is allowed to access the cell. When the cell status

Intra-freq cell reselection ind for SIB3

Indicating whether the UE in idle mode is allowed to reselect another intra-frequency This parameter is valid when [Cell barred indicator for SIB3] is BARRED. It indicates If [Auto-Adaptive Background Noise Update Switch] is set to OFF, it is used to set

The Offset of HSPA Total Power

This parameter specifies the offset between the total HSPA power and the maximum

Inter-frequency Measure Periodical Measurement Report Period

Interval between periodic reporting for the inter-frequency handover. Hysteresis for triggering event 2D.Hysteresis for triggering event 2F.Interval time between detection of event 2D and sending of the measurement report. Interval time between detection of event 2F and sending of the measurement report.This

Inter-freq CS Measure Start Ec/No THD

Ec/No threshold of triggering the inter-frequency measurement for CS services.

Inter-freq CS Measure Stop Ec/No THD

Ec/No threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS

Measure Start Ec/No THD

Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Start Ec/No THD

Ec/No threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS

Measure Stop Ec/No THD

Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Stop Ec/No THD

Ec/No threshold of stopping the inter-frequency measurement for HSPA services.

Inter-freq CS Measure Start RSCP THD

RSCP threshold of triggering the inter-frequency measurement for CS services.

Inter-freq CS Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS

Measure Start RSCP THD

RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Start RSCP THD

RSCP threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS

Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for HSPA services.

Hysteresis for event 2D. This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the

Hysteresis for event 2F.The value of this parameter is associated with slow fading. If this parameter is set to a

2D Event Trigger Delay Time

Interval time between detection of event 2D and sending of the measurement report.

2F Event Trigger Delay Time

Interval time between detection of event 2F and sending of the measurement report.

3A Event Trigger Delay Time

Interval time between detection of event 3A and sending of the measurement report.

Inter-RAT CS Measure Start Ec/No THD

Threshold of triggering inter-RAT measurement for CS services when measurement quantity is



InterRATCSThd2FEcN0

InterRATR99PsThd2DEcN0

InterRATHThd2DEcN0

InterRATR99PsThd2FEcN0

InterRATHThd2FEcN0

InterRATCSThd2DRSCP

InterRATCSThd2FRSCP

InterRATR99PsThd2DRSCP

InterRATHThd2DRSCP

InterRATR99PsThd2FRSCP

InterRATHThd2FRSCP

TargetRatCsThd

TargetRatR99PsThd

TargetRatHThd

IntraRelThdFor1ACSVP

IntraRelThdFor1ACSNVP

IntraRelThdFor1APS

IntraRelThdFor1BCSVP

IntraRelThdFor1BCSNVP

IntraRelThdFor1BPS

HystFor1A 1A Hysteresis

HystFor1B 1B Hysteresis


TrigTime1A

TrigTime1B

Inter-RAT CS Measure Stop Ec/No THD

Threshold of stopping inter-RAT measurement for CS services when measurement quantity is

Inter-RAT R99 PS Measure Start Ec/No THD

Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the

Inter-RAT HSPA Measure Start Ec/No THD

Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is

Inter-RAT R99 PS Measure Stop Ec/No THD


Inter-RAT HSPA Measure Stop Ec/No THD

Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is

Inter-RAT CS Measure Start RSCP THD


Inter-RAT CS Measure Stop RSCP THD

Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Inter-RAT R99 PS



Inter-RAT HSPA Measure Start RSCP THD

Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Inter-RAT R99 PS


Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA



Inter-RAT CS Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for CS domain

Inter-RAT R99 PS Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for PS domain

Inter-RAT HSPA Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for HSPA

VP Service Event 1A Relative Threshold

Relative threshold for event 1A decision when VP service is performed. If this parameter is set to

CS Non-VP Service Event 1A Relative THD

Relative threshold for event 1A decision when non-VP service is performed in CS domain.

PS Service Event 1A Relative Threshold

Relative threshold for event 1A decision when PS service is performed. If this parameter is set to

VP Service Event 1B Relative Threshold

Relative threshold for event 1B decision when VP service is performed. If this parameter is set to CS Non-VP Service

Event 1B Relative Threshold

Relative threshold for event 1B decision when non-VP service is performed in CS domain.

PS Service Event 1B Relative Threshold

Relative threshold for event 1B decision when PS service is performed. If this parameter is set to This parameter specifies the hysteretic value for event 1A. The value of this parameter is This parameter specifies the hysteretic value for event 1B. The value of this parameter is This parameter specifies the hysteretic value for event 1D. The value of this parameter is

Event 1A Triggering Delay

This parameter specifies the interval time between detection of event 1A and sending of the

Event 1B Triggering Delay

This parameter specifies the interval time between detection of event 1B and sending of the



TrigTime1D

MaxCellInActiveSet

IdleQhyst1s

ConnQhyst1s

IdleQhyst2s

ConnQhyst2s

Treselections Reselection delay time

Qqualmin Min quality level

Qrxlevmin Min Rx level

IdleSintrasearch

IdleSintersearch

SsearchRat

PICHPowerOffset PICH Power Offset

AICHPowerOffset AICH Power Offset

T3212

ATT

NMO

DRXCycleLenCoef

T302 Timer 302

N302 Constant 302

T309 Timer 309

T312 Timer 312

N312 Constant 312

T313 Timer 313

N313 Constant 313

T314 Timer 314

T315 Timer 315

N315 Constant 315

CIO Cell Individual Offset

Event 1D Triggering Delay

This parameter specifies the interval time between detection of event 1D and sending of the

Max Number of Cell in Active Set

Maximum number of cells in an active set. This parameter is used to achieve the balance

Hysteresis 1 for idle mode

The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for

Hysteresis 1 for connect mode

The hysteresis value of the serving FDD cells in connected mode in case the quality measurement

Hysteresis 2 for idle mode

The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for

Hysteresis 2 for connect mode

The hysteresis value of the serving FDD cells in connected mode in case the quality measurement If the signal quality (CPICH Ec/No measured by the UE) of a neighboring cell is better The minimum required quality threshold corresponding to CPICH Ec/No. The UE can camp The minimum required RX threshold corresponding to CPICH RSCP. The UE can camp Intra-freq cell

reselection threshold for idle mode

Threshold for intra-frequency cell reselection in idle mode. When the quality (CPICH Ec/No Inter-freq cell

reselection threshold for idle mode

Threshold for inter-frequency cell reselection in idle mode. When the quality (CPICH Ec/No

Inter-RAT cell reselection threshold

Threshold for inter-RAT cell reselection. When the quality (CPICH Ec/No measured by UE) of the Difference between the transmit power of PICH and that of PCPICH. For details, refer to the 3GPP This parameter specifies the power offset between the transmit power of an AICH and that of P-

Periodical location update timer

Periodical location update is implemented by MS through the location update

Attach/detach allowed indication

Indicating whether attach/detach is allowed. NOT_ALLOWED indicates that MS cannot

Network mode of operation

This parameter should be set according to the actual network situation . If there is the Gs

DRX cycle length coefficient

CN domain specific Discontinuous Reception (DRX) cycle length coefficient broadcast on T302 is started after the UE transmits the CELL UPDATE/URA UPDATE message and stopped Maximum number of retransmissions of CELL UPDATE/URA UPDATE.Protocol default T309 is started after the UE is reselected to a cell belonging to anotherT312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive Maximum number of successive "in sync" indications received from L1.T313 is started after the UE detects consecutive N313 "out of sync" indications from L1. T313 Maximum number of successive "out of sync" indications received from L1. Protocol default value T314 is started when the criteria for radio link failure are fulfilled and only radio bearers (RBs) T315 is started when the criteria for radio link failure are fulfilled, and only the radio bearer Maximum number of successive "in sync" indications received from L1 when T313 is It is set according to the topographic feature.



Qqualmin Min Quality Level

Qrxlevmin Min RX level

CellCapContainerFdd

CellCapContainerFdd

CIO

VPLimitInd VPLimitInd

MaxFachPower

FddTpcDlStepSize

DrxCycleLenCoef

T300 Timer 300

N300 Constant 300

T312 Timer 312

N312 Constant 312

PrdReportInterval


HystFor2F 2F Hysteresis

TimeToTrig2D Event 2D Trigger Delay

TimeToTrig2F Event 2F Trigger Delay

InterFreqCSThd2DEcN0

InterFreqCSThd2FEcN0

InterFreqR99PsThd2DEcN0

InterFreqHThd2DEcN0

InterFreqR99PsThd2FEcN0

InterFreqHThd2FEcN0

InterFreqCSThd2DRSCP

InterFreqCSThd2FRSCP

InterFreqR99PsThd2DRSCP

InterFreqHThd2DRSCP

This parameter defines the CPICH Ec/No access threshold of the cell. The UE can camp on the cell This parameter defines the CPICH RSCP access threshold of the cell.This parameter is the

Cell Capability Container

1)DELAY_ACTIVATION_SUPPORT (delay activation support indicator):when the

Cell Capability Container

1)DELAY_ACTIVATION_SUPPORT (delay activation support indicator):when the

Cell oriented Cell Individual Offset

The CIO value specified in this parameter cooperates with the neighboring cell oriented Indicates whether the videophone (VP) service is limited in a cell. When the indicator is "TRUE", it

Max Transmit Power of FACH

The offset between the FACH transmit power and P-CPICH transmit power in a cell.

FDD DL power control step size

Step of the closed-loop power control performed on DL DPCH in Frequency Division

Paging DRX cycle coefficient

UTRAN-specific Discontinuous Reception (DRX) cycle length coefficient. In connected T300 is started when UE sends the RRC CONNECTION REQUEST message. It is Maximum number of retransmissions of the RRC CONNECTION REQUEST message.T312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive Maximum number of successive "in sync" indications received from L1.

Inter-frequency Measure Periodical Measurement Report Period

Interval between periodic reporting for the inter-frequency handover. Hysteresis for triggering event 2D.Hysteresis for triggering event 2F.Interval time between detection of event 2D and sending of the measurement report. Interval time between detection of event 2F and sending of the measurement report.This

Inter-freq CS Measure Start Ec/No THD

Ec/No threshold of triggering the inter-frequency measurement for CS services.

Inter-freq CS Measure Stop Ec/No THD

Ec/No threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS


Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Start Ec/No THD

Ec/No threshold of triggering the inter-frequency measurement for HSPA services.Inter-freq R99 PS


Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Stop Ec/No THD

Ec/No threshold of stopping the inter-frequency measurement for HSPA services.

Inter-freq CS Measure Start RSCP THD

RSCP threshold of triggering the inter-frequency measurement for CS services.

Inter-freq CS Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for CS services.Inter-freq R99 PS


RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Start RSCP THD

RSCP threshold of triggering the inter-frequency measurement for HSPA services.



InterFreqR99PsThd2FRSCP

InterFreqHThd2FRSCP

CIOOffset

IdleQoffset1sn IdleQoffset1sn


Qqualmin Min Quality Level

Qrxlevmin Min RX Level

Hystfor2D 2D Hysteresis

Hystfor2F 2F Hysteresis

TrigTime2D

TrigTime2F

InterRATCSThd2DEcN0

InterRATCSThd2FEcN0

InterRATR99PsThd2DEcN0

InterRATHThd2DEcN0

InterRATR99PsThd2FEcN0

InterRATHThd2FEcN0

InterRATCSThd2DRSCP

InterRATCSThd2FRSCP

InterRATR99PsThd2DRSCP

InterRATHThd2DRSCP

InterRATR99PsThd2FRSCP

InterRATHThd2FRSCP

TargetRatCsThd

TargetRatR99PsThd

TargetRatHThd

IntraRelThdFor1ACSVP

IntraRelThdFor1ACSNVP

IntraRelThdFor1APS

Inter-freq R99 PS Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA

Inter-freq H Measure Stop RSCP THD

RSCP threshold of stopping the inter-frequency measurement for HSPA services.

Neighboring Cell Oriented CIO

Neighboring cell oriented CIO.Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Minimum CPICH Ec/No for the neighboring cell on cell reselection. The neighboring cell can be Minimum CPICH RSCP for the neighboring cell on cell reselection. The neighboring cell can be

Hysteresis for event 2D. This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the

Hysteresis for event 2F.The value of this parameter is associated with slow fading. If this parameter is set to a

2D Event Trigger Delay Time

Interval time between detection of event 2D and sending of the measurement report.

2F Event Trigger Delay Time

Interval time between detection of event 2F and sending of the measurement report.

Inter-RAT CS Measure Start Ec/No THD


Inter-RAT CS Measure Stop Ec/No THD



Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA







Inter-RAT CS Measure Start RSCP THD


Inter-RAT CS Measure Stop RSCP THD







Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the Inter-RAT HSPA



Inter-RAT CS Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for CS domain

Inter-RAT R99 PS Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for PS domain

Inter-RAT HSPA Handover Decision THD

Quality requirement for the cell of another RAT during inter-RAT handover for HSPA

VP Service Event 1A Relative Threshold

Relative threshold for event 1A decision when VP service is performed. If this parameter is set to

CS Non-VP Service Event 1A Relative THD

Relative threshold for event 1A decision when non-VP service is performed in CS domain.

PS Service Event 1A Relative Threshold

Relative threshold for event 1A decision when PS service is performed. If this parameter is set to



IntraRelThdFor1BCSVP

IntraRelThdFor1BCSNVP

IntraRelThdFor1BPS

HystFor1A 1A Hysteresis

HystFor1B 1B Hysteresis


Weight Weighted factor

TrigTime1A

TrigTime1B

TrigTime1D

CIOOffset

CellsForbidden1A

CellsForbidden1B



PCHPower PCH Power

PCPICHPower

Constantvalue

PreambleRetransMax

PowerRampStep Power Increase Step

PowerOffsetPpm Power Offset

PSCHPower PSCH Transmit Power

NB01min

NB01max

Mmax Max Preamble Loop

SSCHPower SSCH Transmit Power

RlRstrTmr RL restoration timer

CNProtclVer CN protocol version

ConnQoffset1sn ConnQoffset1sn

VP Service Event 1B Relative Threshold

Relative threshold for event 1B decision when VP service is performed. If this parameter is set to CS Non-VP Service

Event 1B Relative Threshold

Relative threshold for event 1B decision when non-VP service is performed in CS domain.

PS Service Event 1B Relative Threshold

Relative threshold for event 1B decision when PS service is performed. If this parameter is set to This parameter specifies the hysteretic value for event 1A. The value of this parameter is This parameter specifies the hysteretic value for event 1B. The value of this parameter is This parameter specifies the hysteretic value for event 1D. The value of this parameter is Used for calculating the relative threshold of the soft handover based on the measurement report

Event 1A Triggering Delay

This parameter specifies the interval time between detection of event 1A and sending of the

Event 1B Triggering Delay

This parameter specifies the interval time between detection of event 1B and sending of the

Event 1D Triggering Delay

This parameter specifies the interval time between detection of event 1D and sending of the

Neighboring Cell Oriented CIO

Neighboring cell oriented CIO.

Affect 1A Threshold Flag

Determines whether event 1A threshold is affected when the cell is added to the active set.

Affect 1B Threshold Flag

Flag of whether adding a cell into the active set will affect the relative threshold of the event Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Offset of the PCH transmit power from the PCPICH transmit power in a cell. For detailed

PCPICH Transmit Power

TX power of the PCPICH in a cell. This parameter should be set based on the actual system Constant Value for

Calculating Initial TX Power

This parameter specifies a constant used at calculation of the initial transmit power of the first

Max Preamble Retransmission

The maximum number of preambles transmitted in a preamble ramping cycle. For detailed The power ramp step of the random access preambles transmitted before the UE receives The power offset between the last access preamble and the message control part. Offset of the PSCH transmit power from the PCPICH transmit power in a cell.

Random Back-off Lower Limit

Lower limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and

Random Back-off Upper Limit

Upper limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and The parameter specifies the maximum number of preambles to be used in one preamble ramping Offset of the SSCH transmit power from the PCPICH transmit power in a cell.A timer to RNC wait for radio link restoration indication in the radio link procedure.Protocol version supported by the CN.Cell offset used for CPICH RSCP measurement value in cell selection or




FilterCoef

IntraFreqMeasQuantity

PeriodMRReportNumfor1A

ReportIntervalfor1A

PeriodMRReportNumfor1C

ReportIntervalfor1C

HystFor1C 1C Hysteresis

TrigTime1C

MaxCellInActiveSet



ConnSintrasearch

ConnSintersearch

IntraFreqFilterCoef

IntraFreqMeasQuantity

PeriodMRReportNumfor1A

ReportIntervalfor1A

PeriodMRReportNumfor1C

ReportIntervalfor1C

HystFor1C 1C Hysteresis

Weight Weighted factor

TrigTime1C

ConnCellBarred

ConnIntraFreqReselection

ConnTbarred Time barred for SIB4

CIOOffset

DRA_HSDPA_STATE_TRANS_SWITCH

DRA_HSUPA_STATE_TRANS_SWITCH

Cell offset used for CPICH Ec/No measurement value in cell selection or

Intra-frequency L3 Filter Coefficient

This parameter specifies the Layer 3 filter coefficient for the intra-frequency measurement.

Intra-frequency Measurement Quantity

Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies

Event 1A to Periodical Report Number

Maximum number of reporting event 1A after the reporting mode is changed to periodical

Event 1A to Periodical Report Period

Interval at which event 1A is reported after the reporting mode is changed to periodical

Event 1C to Periodical Report Number

Maximum number of reporting event 1C after the reporting mode is changed to periodical

Event 1C to Periodical Report Period

Interval at which event 1A is reported after the reporting mode is changed to periodical This parameter specifies the hysteretic value for event 1C. The value of this parameter is

Event 1C Triggering Delay

This parameter specifies the interval time between detection of event 1C and sending of the

Max Number of Cell in Active Set

Maximum number of cells in an active set. This parameter is used to achieve the balance Cell offset used for CPICH RSCP measurement value in cell selection or Cell offset used for CPICH Ec/No measurement value in cell selection or Intra-freq cell

reselection threshold for connect mode

Threshold for intra-frequency cell reselection in connected mode. When the quality (CPICH Inter-freq cell

reselection threshold for connect mode

Threshold for inter-frequency cell reselection in connected mode. When the quality (CPICH

Intra-frequency L3 Filter Coefficient

This parameter specifies the Layer 3 filter coefficient for the intra-frequency measurement.

Intra-frequency Measurement Quantity

Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies

Event 1A to Periodical Report Number

Maximum number of reporting event 1A after the reporting mode is changed to periodical

Event 1A to Periodical Report Period

Interval at which event 1A is reported after the reporting mode is changed to periodical

Event 1C to Periodical Report Number

Maximum number of reporting event 1C after the reporting mode is changed to periodical

Event 1C to Periodical Report Period

Interval at which event 1A is reported after the reporting mode is changed to periodical This parameter specifies the hysteretic value for event 1C. The value of this parameter is Used for calculating the relative threshold of the soft handover based on the measurement report

Event 1C Triggering Delay

This parameter specifies the interval time between detection of event 1C and sending of the

Cell barred indicator for SIB4

Indicating whether the UE in connected mode is allowed to access the cell. When the cell status

Intra-freq cell reselection ind for SIB4

Indicating whether the UE in idle mode is allowed to reselect another intra-frequency This parameter is valid when [Cell barred indicator for SIB4] is BARRED. It indicates

Neighboring Cell-Oriented CIO

Cell individual offset for the GSM cell.

Dynamic Resource Allocation Switch

Dynamic resource allocation switch group.





DRA_PS_BE_STATE_TRANS_SWITCH

PsInactTmrForCon

PsInactTmrForStr Streaming service T1

PsInactTmrForInt Interactive service T1

PsInactTmrForBac Background service T1

D2FTvmTimeToTrig BE D2F/R 4B Time

F2PTvmTimeToTrig BE F2P 4B Time

BeF2PStateTransTimer

BeF2DTvmThd BE F/R2D 4A Threshold

BeF2DTvmTimeToTrig BE F/R2D 4A Time

CellReSelectTimer Cell Reselection Timer

BeD2FStateTransTimer

BeH2FStateTransTimer

RlMaxDlPwr RL Max DL TX power

RlMinDlPwr RL Min DL TX power

TargetFreqCsThdEcN0

TargetFreqR99PsThdEcN0

TargetFreqHThdEcN0

TargetFreqCsThdRscp

TargetFreqR99PsThdRscp

TargetFreqHThdRscp

TargetFreqCsThdEcN0

TargetFreqHThdEcN0

TargetFreqR99PsThdEcN0

TargetFreqCsThdRscp

TargetFreqHThdRscp

TargetFreqR99PsThdRscp



Conversational service T1

When detecting that the Ps' Conversational User had no data to transfer for a long time which When detecting that the Ps' Streaming User had no data to transfer for a long time which longer When detecting that the Ps' Interactive User had no data to transfer for a long time which longer When detecting that the Ps' Background User had no data to transfer for a long time which longer When the traffic volume is below the 4B threshold and remains so for the period specified by this When the traffic volume is below the 4B threshold and remains so for the period specified by this

BE FACH or E_FACH to PCH Transition Timer

Timer for state transition from FACH or E_FACH to PCH of BE services, used to check whether This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH This parameter specifies the occurrence time of 4A event for triggering the transition of BE Length of the cell reselection frequency timer. This parameter is used together with

BE DCH to FACH Transition Timer

Timer for state transition from DCH to FACH of BE services, used to check whether the UE in the

BE HS-DSCH to FACH Transition Timer

Timer for state transition from HS-DSCH to FACH of BE services, used to check whether the UE in This parameter specifies the maximum DL RL power to be assigned.This parameter specifies the minimum DL RL power to be assigned.Inter-freq CS Target

Frequency Trigger Ec/No THD

Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq R99 PS

Target Frequency Trigger Ec/No THD

Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq HSPA Target


Threshold of the target frequency for triggering inter-frequency measurement based on Inter-freq CS Target

Frequency Trigger RSCP THD


Target Frequency Trigger RSCP THD








Target Frequency Trigger Ec/No THD






Target Frequency Trigger RSCP THD

Threshold of the target frequency for triggering inter-frequency measurement based on



Tcell Time Offset

PScrambCode

LAC Location Area Code

SAC Service Area Code

RAC Routing Area Code

CellId Cell ID

UARFCNDownlink Downlink UARFCN

Qhyst1spch

Qhyst1sfach

Qhyst2spch

Qhyst2sfach

Treselectionspch

Treselectionsfach

InterRATPeriodReportInterval

TimeToTrigForVerify

InterRATPingPongTimer

HsScchCodeNum

HoSwitch HandOver Switch



InterFreqFilterCoef

FilterCoefOf2D2F 2D/2F Filter Coefficient

InterRATFilterCoef

MAXTARGETULLOADFACTOR

MAXHSUPAUSERNUM

10ms Initial SIR Target

2ms Initial SIR Target

10ms Max SIR Target

Difference between the System Frame Number (SFN) and NodeB Frame Number (BFN) of the

DL Primary Scrambling Code

Sequence Number of a DL primary scrambling code in a cell. For detailed information of Identifies a location area code for a Public Land Mobile Network (PLMN) of the GSM-MAP type. It MCC,MNC,LAC and SAC together compose the Service Area ID (SAI). SAI = MCC || MNC || Identifying a routing area in a location area for a Public Land Mobile Network (PLMN)of GSM-ID of a cell. For detailed information about this parameter, see 3GPP TS 25.401.Depending on the value of [Band indication], as shown below:Hysteresis 1 for UE in

CELL_PCH or URA_PCH state

This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement

Hysteresis 1for UE in CELL_FACH state

This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis Hysteresis 2 for UE in

CELL_PCH or URA_PCH state

This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement

Hysteresis 2 for UE in CELL_FACH state

This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis

Reselection delay time for UE in PCH state

This parameter indicates the UE reselection delay in the CELL_PCH or URA_PCH connection Reselection delay time

for UE in CELL_FACH state

This parameter indicates the UE reselection delay in the CELL_FACH connection mode. This

Inter-RAT Period Reporting Interval

Interval that the UE reports inter-RAT measurement results to the RNC.Time to Trigger

Handover to Verified GSM Cell

Time delay for triggering handovers to GSM cells with verified BSIC.

Inter-RAT Ping-Pong Timer

Length of the timer to avoid ping-pong handovers between 2G and 3G networks.

Code Number for HS-SCCH

This parameter decides the maximum number of subscribers that the NodeB can schedule in a

HandOver switch group.1) HO_ALGO_HCS_SPEED_EST_SWITCH: When the switch is on, the RNC



Inter-frequency Measure Filter Coeff

This parameter specifies the Layer 3 filter coefficient for the inter-frequency measurementL3 filtering coefficient for event 2D or event 2F measurement

Inter-RAT Filter Coefficient

This parameter specifies the Layer 3 filter coefficient for the inter-RAT measurement.

UL Target Load Factor

The parameter specifies the target value of the uplink load, which is decreased through

HSUPA power control on the NodeB side. For

details about this parameter, refer to 3GPP

TS 25.433

Cell Max HSUPA User Number

defines the admission limit for the number of

EUL users in a cellINITSIRTARGET（10ms）

Defining the initial SIR target value of outer loop power control algorithm

INITSIRTARGET（2ms）

Defining the initial SIR target value of outer loop power control algorithm

MAXSIRTARGET（10ms）

Defining the maximum SIR target value of outer

loop power control algorithm



2ms Max SIR Target

MINSIRTARGET Min SIR Target

ERGCH2INDSTPTHS,ERGCH3INDSTPTHS

CQIFBCK(CQIFBCKFORSHO)

MAXSIRTARGET（2ms）

Defining the maximum SIR target value of outer


Defining the minimum SIR target value of outer


reference-E-TFCIreference-E-TFCI-PO

The EDCH Channel PowerOffset

Defining the EDCH Channel PowerOffset

TwoIndexStepThreshold；

ThreeIndexStepThreshold

TwoIndexStepThreshold；

ThreeIndexStepThreshold

EDCHTARGETLITTLERETRANSNUM（10ms） 10ms Target Small Retransmisson

EDCHTARGETLITTLERETRANSNUM（2ms） 2ms Target Small RetransmissonPeriodic of CQI

Feedback



MML Command Baseline Value Remarks

ADD U2GNCELL -50~50 0

ADD U2GNCELL -58~-13 -50

ADD UBCH -350~150 -20

ADD UCELLSETUP 0~500 430




ADD UCELLSETUP -20~20 0

ADD UCELLQUICKSETUP -100~500 330

ADD UCELLACCESSSTRICT NOT_RESERVED

ADD UCELLACCESSSTRICT NOT_BARRED
















Parameter Value Range

RESERVED, NOT_RESERVEDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARREDBARRED, NOT_BARRED



ADD UCELLACCESSSTRICT None

ADD UCELLACCESSSTRICT ALLOWED

ADD UCELLACCESSSTRICT D320

ADD UCELLCAC 0~621 61

-500~0 0

D500

0~29 4

0~29 4

D320

D1280

-24~0 -14

-24~0 -12

-24~0 -14

-24~0 -14

-24~0 -12

-24~0 -12

-115~-25 -95

-115~-25 -92

-115~-25 -95

-115~-25 -95

-115~-25 -92

-115~-25 -92

0~29 4

0~29 4

D320

D1280

D0

-24~0 -14

BARRED, NOT_BARREDALLOWED, NOT_ALLOWEDD10, D20, D40, D80, D160, D320, D640, D1280

ADD UCELLHSDPA

Huawei suggests 0, it can improve power usage efficency and HSPA

ADD UCELLINTERFREQHOCOV

NON_PERIODIC_REPORT(Non periodical reporting), D250~1




D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,


D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,













ADD UCELLINTERRATHOCOV



D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,


D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,


D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,




-24~0 -12

-24~0 -15

-24~0 -15

-24~0 -13

-24~0 -13

-115~-25 -100

-115~-25 -97

-115~-25 -110

-115~-25 -110

-115~-25 -107

-115~-25 -107

0~63 16

0~63 16

0~63 16

0~29 6

0~29 6

0~29 6

0~29 12

0~29 12

0~29 12

0~15 0

0~15 0

0~15 8

D320

D640















ADD UCELLINTRAFREQHO










D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,


D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,



D640

1~6 3

0~20 2

0~20 2

0~20, 255 1

0~20, 255 1

0~31 1

-24~0 -18

-58~-13 -58

-16~10, 127 5

-16~10, 127 4

-16~10, 127 2

ADD UCHPWROFFSET -10~5 -7

ADD UCHPWROFFSET -22~5 -6

0~255 10

ALLOWED

MODE1, MODE2 MODE2

6~9 6

SET UCONNMODETIMER D2000

SET UCONNMODETIMER 0~7 3




SET UCONNMODETIMER 0~15 3 OK





-50~50 0


D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,


ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCNDOMAIN

ADD UCNDOMAIN NOT_ALLOWED, ALLOWED

ADD UCNDOMAIN

ADD UCNDOMAIN

Huawei suggests 6, because paging delay is big when this parameter is

D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600,

D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000

D1, D2, D4, D10, D20, D50, D100, D200

NOK:50, Avoid call drop,

D0, D2, D4, D6, D8, D12, D16, D20D0, D10, D30, D60, D180, D600, D1200, D1800D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000

ADD UEXT2GCELL



-24~0 -18

-58~-13

None

None

-20~20 0

ADD UCELLSETUP TRUE, FALSE 0

ADD UFACH -350~150 10

SET UFRC STEPSIZE_1DB

SET UFRC 3~9 6

SET UIDLEMODETIMER D2000

SET UIDLEMODETIMER 0~7 3

SET UIDLEMODETIMER 1~15 6

SET UIDLEMODETIMER D1

SET UINTERFREQHOCOV D500

SET UINTERFREQHOCOV 0~29 4

SET UINTERFREQHOCOV 0~29 4



SET UINTERFREQHOCOV -24~0 -14






SET UINTERFREQHOCOV -115~-25 -95




ADD UEXT3GCELL

ADD UEXT3GCELL无

ADD UEXT3GCELL

DELAY_ACTIVATION_SUPPORT(delay activation support indication),

ADD UEXT3GCELL

DELAY_ACTIVATION_SUPPORT(delay activation support indication),

ADD UEXT3GCELL

STEPSIZE_0.5DB, STEPSIZE_1DB, STEPSIZE_1.5DB, STEPSIZE_2DB

We suggest 1dB.HW Power control performance for 1dB step is Huawei suggests 6, because paging delay is big when this parameter is

D100, D200, D400, D600, D800, D1000, D1200, D1400, D1600,

D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800, D1000NON_PERIODIC_REPORT(Non periodical reporting), D250~1

D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,





-20~20 0

-50~50 0

-50~50 0

-24~0 -18

-58~-13

SET UINTERRATHOCOV 0~29 4


SET UINTERRATHOCOV D320

SET UINTERRATHOCOV D1280

SET UINTERRATHOCOV -24~0 -14






SET UINTERRATHOCOV -115~-25 -100









SET UINTRAFREQHO 0~29 6



ADD UINTERFREQNCELL

ADD UINTERFREQNCELL

ADD UINTERFREQNCELL

ADD UINTERFREQNCELL

ADD UINTERFREQNCELL无


6=3dB,use huawei default6=3dB,use huawei default










SET UINTRAFREQHO D320



-20~20 0

AFFECT

AFFECT

-50~50 0

-50~50 0

ADD UPCH -350~150 -20

ADD UPCPICH -100~500 330

ADD UPRACHBASIC -35~-10 -20

ADD UPRACHBASIC 1~64 20

ADD UPRACHBASIC 1~8 2

ADD UPRACHTFC -5~10

ADD UPSCH -350~150 -50

0~50 0

0~50 0

1~32 8

ADD USSCH -350~150 -50

SET USTATETIMER 1~300000 11000

None

-50~50 0


HW suggests D1280 to avoid PingPang handover.

D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,

ADD UINTRAFREQNCELL

ADD UINTRAFREQNCELL AFFECT, NOT_AFFECT

ADD UINTRAFREQNCELL AFFECT, NOT_AFFECT

ADD UINTRAFREQNCELL

ADD UINTRAFREQNCELL

In signaling transmission mode, set PowerOffsetPpm to

ADD URACH

ADD URACH

ADD URACH

ADD UCNNODE(Mandatory) R99, R4, R5, R6, R7, R8

ADD UINTERFREQNCELL



-50~50 0

SET UINTRAFREQHO D3

SET UINTRAFREQHO CPICH_EC/NO


SET UINTRAFREQHO D4000 4s is enough


SET UINTRAFREQHO D4000 4s is enough




-50~50 0

-50~50 0

-16~10, 127 5

-16~10, 127 4

D3

CPICH_EC/NO

D16

D4000

D16

D4000

0~15 8

0~20 0

D640

ADD UCELLACCESSSTRICT None

ADD UCELLACCESSSTRICT NOT_ALLOWED

ADD UCELLACCESSSTRICT D1280

ADD U2GNCELL -50~50 0

SET UCORRMALGOSWITCH


ADD UINTERFREQNCELL D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19CPICH_EC/NO, CPICH_RSCPD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITYNON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5 D1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITYNON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5 D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,

ADD UINTRAFREQNCELL

ADD UINTRAFREQNCELL

ADD UCELLSELRESEL

ADD UCELLSELRESEL


D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17, D19

ADD UCELLINTRAFREQHO CPICH_EC/NO, CPICH_RSCP

ADD UCELLINTRAFREQHOD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITY


NON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5

ADD UCELLINTRAFREQHOD1~0 D2~1 D4~2 D8~3 D16~4 D32~5 D64~6 INFINITY


NON_PERIODIC_REPORT, D250~1 D500~2 D1000~3 D2000~4 D4000~5




D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640, BARRED, NOT_BARREDALLOWED, NOT_ALLOWEDD10(10 seconds), D20(20 seconds), D40(40 seconds), D80(80 seconds), DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O

DRA_AQM_SWITCH:OFF, DRA_BASE_ADM_CE_BE_TTI_L2_O

HW suggests DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:OFF

DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O






SET UPSINACTTIMER 0~14400 20




SET UUESTATETRANS D5000


SET UUESTATETRANSTIMER 1~65535 65535





SET UUESTATETRANSTIMER 1~65535 5 OK,5->20

-350~150 None

-350~150 None







-24~0 -12

-24~0 -12

-24~0 -12

-115~-25 -92

-115~-25 -92

ADD UCELLINTERFREQHOCOV -115~-25 -92

DRA_AQM_SWITCH, DRA_BASE_ADM_CE_BE_TTI_L2_O



D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,

HW suggests a bigger trigger timer to prevent PingPang D2F

D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,

HW suggests a bigger value to prevent PingPong F2P.because there are big delay for data transmission if UE is in PCH status, so

D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k, D6k, D8k, D12k, D16k, D24k, D0, D10, D20, D40, D60, D80, D100, D120, D160, D200, D240, D320, D640,

HW suggests D0 because it can speed up data transmission and

ADD UCELLRLPWR

ADD UCELLRLPWR

Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in



Threshold for InterFrequency HO should be discussed in






Threshold for InterFrequency HO should be discussed in Threshold for InterFrequency HO should be discussed in



ADD UCELLSETUP None

ADD UCELLSETUP 0~511 None

ADD UCELLSETUP 1~65533, 65535 None





0~40, 255 255

0~40, 255 255

0~40, 255 255

0~40, 255 255

0~31, 255 255

0~31, 255 255

D1000

ADD UCELLINTERRATHOCOV 0~64000 0

0~65535 0

ADD UCELLHSDPA 1~15 4




D3

D3

ADD UCELLHSUPA 75 75

ADD UCELLCAC 20 20

ADD UTYPRABHSUPAPC 0-255 162



CHIP0, CHIP256, CHIP512, CHIP768, CHIP1024, CHIP1280,

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL

ADD UCELLSELRESEL


NON_PERIODIC_REPORT(Non periodical reporting), D250~1


HO_ALGO_HCS_SPEED_EST_SWITCH, HO_ALGO_LDR_A

HO_ALGO_HCS_SPEED_EST_SWITCH:OFF, HO_ALGO_LDR_A

We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERL

HO_ALGO_HCS_SPEED_EST_SWITCH, HO_ALGO_LDR_A


We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERLHO_ALGO_HCS_S

PEED_EST_SWITCH, HO_ALGO_LDR_A


We suggest HO_MC_SIGNAL_SWITCH:OFF, HO_ALGO_OVERLADD

UCELLINTERFREQHONCOV


For low speed(5km/h):Range is D4~D6, the recommended





0~100

0~100

8dB：（X-82)/10

8dB：（X-82)/10

11dB：（X-82)/10





ADD UTYPRABHSUPAPC

ADD UTYPRABHSUPAPC

ADD UTYPRABOLPC 1-100 1% 1%

ADD UTYPRABOLPC 10% 10%

ADD UHSDPCCH 2 2ms

14dB：（X-82)/10

-2dB：（X-82)/10REFETFCIIDX1=4,

REFETFCIIDX2=54,

REFETFCIPO1=PO_15/15,

REFETFCIPO2=PO_67/15

ERGCH2INDSTPTHS=12,

ERGCH3INDSTPTHS=9



NSN

RU20

Parameter ID Meaning

AdjgQoffset1 0 dB

AdjgQrxlevMin -115 dBm

PtxPrimaryCCPCH -5dbm

PtxCellMax 43 dBm

PtxPrimaryCPICH 33 dBm

Cell_Reserved Not reserved

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

ACBarredList 0

Parameter Value Range

Recommended Value

This parameter is used in the cell re-selection and ranking between WCDMA and GSM cells. The value of this parameter is subtracted from the measured GSM carrier RSSI of the neighbouring cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.

-50...50 dB, step 1 dB

Determines the minimum required RSSI level which the measurement result of the GSM neighbour cell must exceed before the cell re-selection becomes possible./nThis parameter is part of System Information Block 11&12.

-115...-25 dBm, step 2 dBm

This is the transmission power of the primary CCPCH relative to the CPICH transmission power. The P-CCPCH is a fixed rate (15 ksps, SF = 256) downlink physical channel used to carry the BCH. It is a pure data channel and characterized by a fixed channelisation code (Cch,256,1). The P-CCPCH is broadcast over the entire cell and it is not transmitted during the first 256 chips of each slot, where Primary SCH and Secondary SCH are transmitted. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.

-35...15 dB, step 0.1 dB

This parameter defines the maximum transmission power of the cell. The maximum transmission power is the maximum value for the linear sum of the power of all downlink physical channels that is allowed to be used in a cell. The maximum transmission power of the cell is the minimum of the two parameters: PtxCellMax and MaxDLPowerCapability (the maximum BTS power capability). The RNC signals the BTS the minimum value as the maximum transmission power in Maximum Transmission Power IE (TS 25.433). The RNC uses the minimum value as the maximum transmission power of the cell. If HSDPA static resource allocation is active, the value of the PtxMaxHSDPA parameter added with the value of the PtxTargetHSDPA parameter must not exceed the cell maximum transmission power defined by the minimum of the following parameters: PtxCellMax and MaxDLPowerCapability. Otherwise Rthe NC internally limits the HSDPA power.

0...50 dBm, step 0.1 dBm

This is the transmission power of the primary common pilot channel. The P-CPICH physical channel carries the common pilots of the cell, which is defined in the cell setup. The transmission power of the CPICH physical channel defines the actual cell size, which means that the power is determined by radio network planning. This parameter is used, for example, for neighbour measurements - critical for the network performance. The default value is 5-10% of the maximum transmitting power of WCDMA BTS, which can be, for example, 43 dBm/carrier. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. Note: The cell is blocked if the WCDMA BTS does not support the used value. Typical supported range is (Cell max power - 18dB)..(Cell max power - 3dB). This parameter is part of System Information Block 5.

-10...50 dBm, step 0.1 dBm

Defines whether the cell is reserved for operator use or not. A reserved cell is a cell on which camping is not allowed, except for particular UEs, if so indicated./nWhen cell status is 'not barred' and 'not reserved' for operator use the UE may select//re-select this cell during the cell selection and cell re-selection procedures in Idle mode and in Connected mode./nWhen cell status is 'not barred' and 'reserved' for operator use, the UEs assigned to Access Class 11 or 15 may select//re-select this cell if in the home PLMN. UEs assigned to Access Class in the range 0 to 9 and 12 to 14 shall behave as if cell status 'barred' is indicated./nThis parameter is part of System Information Block 3.

Reserved (0), Not reserved (1)

Access Class Barred list' information defines whether access is barred for each of the 16 Access Classes (AC0...AC15). 'Access Class Barred list' uses a binary notation of 16 bits where - bit 0 indicates whether access is barred for AC0 - bit 1 indicates whether access is barred for AC1 - bit 2 indicates whether access is barred for AC2 ... - bit 15 indicates whether access is barred for AC15 If a bit is set to 1, the corresponding Access Class is 'barred'. If a bit is set to 0, the corresponding Access Class is 'not barred'. If Access Class 10 is indicated as barred in a cell, UEs with Access Class 0 to 9 or without an IMSI are not allowed to initiate emergency calls in this cell. For UEs with Access Classes 11 to 15, emergency calls are not allowed if both Access Class 10 and the relevant Access Class (11 to 15) are barred. Otherwise, emergency calls are allowed for those UEs. Note: This value is used in SIB3 only when AccessClassRegulation is disabled in a cell. If AccessClassRegulation is enabled, only Access Classes 10 to 15 can be barred with this parameter.

Bit 0: Access Class 0, Bit 1: Access Class 1, Bit 2: Access Class 2, Bit 3: Access Class 3, Bit 4: Access Class 4, Bit 5: Access Class 5, Bit 6: Access Class 6, Bit 7: Access Class 7, Bit 8: Access Class 8, Bit 9: Access Class 9, Bit 10: Access Class 10, Bit 11: Access Class 11, Bit 12: Access Class 12, Bit 13: Access Class 13, Bit 14: Access Class 14, Bit 15: Access Class 15

































CellBarred Not barred

Allowed

Tbarred 40 s

PrxNoise -101.9 dBm

PtxMaxHSDPA 38.5 dBm

0.5 s

640 ms

HHoEcNoCancelTime 640 ms

HHoEcNoThreshold -24~0 -12dbm

HHoEcNoCancel -24~0 -9dbm





HHoRscpThreshold -115~-25 -105dbm

HHoRscpCancel -115~-25 -102dbm





640 ms



Defines whether the cell is barred or not./nA barred cell is a cell where a UE is not allowed to camp on. Emergency calls shall be allowed in all cells whose barred status is 'not barred'. When cell status is 'barred', the UE is not permitted to select//re-select the cell, not even for emergency calls./nThis parameter is part of System Information Block 3.

Barred (0), Not barred (1)

IntraFreq_Cell_Reselect_Ind

Defines whether intra-frequency cell re-selection is allowed or not when the cell is barred./nWhen a cell's status is 'barred', the UE is not permitted to select//re-select this cell, except in some cases for an emergency call. If the 'Intra-frequency cell re-selection indicator' is set to value 'allowed', the UE may select another cell on the same frequency if selection//re-selection criteria are fulfilled. If the 'Intra-frequency cell re-selection indicator' is set to 'not allowed' the UE shall not re-select even a different cell on the same frequency as the barred cell. For emergency call, the Intra-frequency cell re-selection indicator IE' shall be ignored. 'Intra-frequency cell re-selection indicator' is part of SIB3//4 in the case the 'cell barred' indicator is true./nThis parameter is part of System Information Block 3.

Allowed (0), Not allowed (1)

When the cell is barred, the UE must check between the time interval ‘Cell barred period’, whether the status of the barred cell has changed./nThis parameter is part of the System Information Block 3.

10 s (0), 20 s (1), 40 s (2), 80 s (3), 160 s (4), 320 s (5), 640 s (6), 1280 s (7)

Defines the noise level in the BTS digital receiver when there is no load (thermal noise + noise figure). This parameter is needed in noise rise calculations.

-130...-50 dBm, step 0.1 dBm

The parameter defines the maximum allowed HSDPA transmission power.

-10...50 dBm, step 0.1 dBm

InterFreqMeasRepInterval

This parameter determines the measurement reporting interval for periodical inter-frequency measurements.

0.5 s (2), 1 s (3), 2 s (4), 3 s (5), 4 s (6)

HHoEcNoTimeHysteresis

If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than the threshold HHoEcNoThreshold. The parameter HHoEcNoTimeHysteresis determines the time period during which the CPICH Ec/No of the active set cell must stay worse than the threshold HHoEcNoThreshold before the UE can trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.

0 ms (0), 10 ms (1), 20 ms (2), 40 ms (3), 60 ms (4), 80 ms (5), 100 ms (6), 120 ms (7), 160 ms (8), 200 ms (9), 240 ms (10), 320 ms (11), 640 ms (12), 1280 ms (13), 2560 ms (14), 5000 ms (15)

If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. The parameter HHoEcNoCancelTime determines the time period during which the CPICH Ec/No of the active set cell must stay better than the threshold HHoEcNoCancel before the UE can trigger the reporting event 1E. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.


If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH Ec/No measurement result of an active set cell becomes worse than or equal to an absolute CPICH Ec/No threshold. The parameter HHoEcNoThreshold determines the absolute CPICH Ec/No threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH Ec/No of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.

If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH Ec/No is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH Ec/No. The RNC cancels the event 1F of an active set cell if the CPICH Ec/No measurement result of the active set cell becomes better than or equal to the threshold HHoEcNoCancel and the UE transmits the corresponding event 1E triggered Measurement Report to the RNC. Note that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH Ec/No, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH Ec/No.





If the inter-frequency or inter-RAT (GSM) handover caused by low measured CPICH RSCP is enabled, the UE transmits an event 1F triggered measurement report to the RNC when the CPICH RSCP measurement result of an active set cell becomes worse than or equal to an absolute CPICH RSCP threshold. The parameter HHoRscpThreshold determines the absolute CPICH RSCP threshold which is used by the UE to trigger the reporting event 1F. When the measured CPICH RSCP of all active set cells has become worse than or equal to the threshold in question, the RNC starts inter-frequency or inter-RAT (GSM) measurements in compressed mode for the purpose of hard handover.

If the inter-frequency or inter-RAT (GSM) handover caused by low measured absolute CPICH RSCP is enabled, the RNC starts the inter-frequency or GSM measurement in compressed mode when all active set cells have triggered the reporting event 1F for CPICH RSCP. The RNC cancels the event 1F of an active set cell, if the CPICH RSCP measurement result of the active set cell becomes better than or equal to the threshold HHoRscpCancel and the UE transmits the corresponding event 1E triggered measurement report to the RNC. Note, that once the RNC has started the inter-frequency or inter-RAT (GSM) measurement for the purpose of hard handover due to low measured absolute CPICH RSCP, the RNC does not break off the ongoing measurement, even if one or more active set cells trigger the reporting event 1E for CPICH RSCP.
























AdjgRxLevMinHO 8

AdjgRxLevMinHO 8

AdjgRxLevMinHO 8

AdditionWindow 4 dB

AdditionWindow 4 dB

AdditionWindow 4 dB

DropWindow 6 dB

DropWindow 6 dB

DropWindow 6 dB

AdditionTime 100 ms

DropTime 640 ms












This parameter determines the minimum required GSM RSSI level which the averaged RSSI value of the GSMneighbour cell must exceed before the coverage (or quality) reason handover to GSM is possible.

-110...-47 dBm, step 1 dBm


-110...-47 dBm, step 1 dBm


-110...-47 dBm, step 1 dBm

Addition Window determines the relative threshold (A_Win) used by the UE to calculate the reporting range of event 1A. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best), or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of a monitored cell (M_new) enters the reporting range, the UE transmits a Measurement Report to the RNC in order to add the monitored cell into the active set: M_new >= W * M_sum + ( 1 - W )* M_best - A_Win This parameter is part of System Information Block 11/12.

0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB

Drop Window determines the relative threshold (D_Win) which is used by the UE to calculate the reporting range of event 1B. The threshold is either relative to the CPICH Ec/No measurement result of the best active set cell (M_best) or to the sum of active set measurement results (M_sum), depending on the value of the parameter Active Set Weighting Coefficient (W). When the CPICH Ec/No measurement result of an active set cell (M_old) leaves the reporting range, the UE transmits a Measurement Report to the RNC in order to remove the cell from the active set: M_old <= W * M_sum + ( 1 - W )* M_best - D_Win This parameter is part of System Information Block 11/12.

0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB

When a monitored cell enters the reporting range (addition window), the cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to add the cell into the active set (event 1A). The length of this period is controlled by the parameter Addition Time. This parameter is part of System Information Block 11/12.


When an active set cell leaves the reporting range (drop window), the cell must continuously stay outside the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to remove the cell from the active set (event 1B). The length of this period is controlled by the parameter Drop Time. This parameter is part of System Information Block 11/12.




MaxActiveSetSize 2...3, step 1 3

Qhyst1 0 dB

Qhyst1 0 dB

Qhyst2 2 dB

Qhyst2 2 dB

Treselection 2 s

QqualMin -18 dB

QrxlevMin -115 dBm

Sintrasearch 10db

Sintersearch 8 dB

Ssearch_RAT 4 dB

PTxPICH -8 dB

PtxAICH -8 dB

CS_T3212 0 decihours

PS_NMO

UTRAN_DRX_length 320 ms

T302 2000 ms

N302 0...7, step 1 7

T309 1...8 s, step 1 s 8

T312conn 6s

N312 4 (2)

T313 3 s

N313 20 (4)

T314 4s

T315 180 s

N315 1

This parameter determines the maximum number of cells which can participate in a soft/softer handover. Reporting deactivation threshold indicates the maximum number of cells allowed in the active set in order for the event 1A to trigger. The RNC calculates the deactivation threshold from the parameter MaxActiveSetSize: Reporting Deactivation Threshold = MaxActiveSetSize - 1 Reporting Deactivation Threshold parameter is part of System Information Block 11/12. Replacement activation threshold information element indicates the minimum number of cells allowed in the active set in order for the event 1C to trigger. The threshold equals to the maximum size of the active set which is controlled with the parameter MaxActiveSetSize. Replacement Activation Threshold parameter is part of System Information Block 11/12.

Qhyst1 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH RSCP./nThis parameter is part of System Information Block 3.

0...40 dB, step 2 dB

Qhyst1 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH RSCP./nThis parameter is part of System Information Block 3.


Qhyst2 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH ECNO./nThis parameter is part of System Information Block 3.


Qhyst2 is used for TDD and GSM cells, and for FDD cells when cell selection and re-selection quality measure is set to CPICH ECNO./nThis parameter is part of System Information Block 3.


The UE triggers the reselection of a new cell if the cell reselection criteria are fulfilled during the time interval Treselection./nThis parameter is part of System Information Block 3.

0...31 s, step 1 sThe minimum required quality

level in the cell (Ec//No)./nThis parameter is part of System Information Block 3.

-24...0 dB, step 1 dB


-115...-25 dBm, step 2 dBm

The threshold for intra-frequency measurements, and for the HCS measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.


The threshold for inter-frequency measurements, and for the HCS measurement rules. /nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.


The RAT-specific threshold for inter-RAT measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.


This is the transmission power of the PICH channel. It carries the paging indicators which tell the UE to read the paging message from the associated secondary CCPCH. The transmission power value is relative to the CPICH transmission power. It may depend on the number of paging indicators (PI) per frame. The following table shows the recommended values for the different cases N. PI per frame (NP), Repetition of PICH bits, Power relative to CPICH (dB): 18, 16, -10 36, 8, -10 72, 4, -8 144, 2, -5 This parameter is part of System Information Block 5.

-10...5 dB, step 1 dB

This is the transmission power of one Aquisition Indicator (AI) compared to CPICH power. If a WCDMA BTS transmits a large number of AIs, then the total power of AICH increases. The AICH consists of a repeated sequence of 15 consecutive Access Slots (AS), each one 5120 chips in length. Each access slot consists of two parts: an Acquisition Indicator (AI) part consisting of 32 real-valued symbols, and a second part, 1024 chips in length, which has no transmission and is not formally part of the AICH. This second part of the slot is reserved for possible use by CSICH, or possible future use by other physical channels. The spreading factor (SF) used for the channelisation of the AICH is 256, and the phase reference for the AICH is the P-CPICH. This parameter is part of System Information Block 5.

-22...5 dB, step 1 dB

The timeout value, in decihours (6 min), for periodic location updating. Given only for CS domain. (Part of CS domain specific NAS System information in SIB1). /nThe value 0 is used for an infinite timeout value, that is, periodic location updating is not used./nThis parameter is part of System Information Block 1.

0...255 decihours, step 1 decihours

CSAttachDetachAllowed

Defines whether IMSI attach and detach are allowed or not. /n0 = MSs shall not apply IMSI attach and detach procedure, /n1 = MSs shall apply IMSI attach and detach procedure. /nParameter is given only for CS domain. (Part of CS domain specific NAS System information in SIB1.)

IMSI attach/detach not allowed (0), IMSI attach/detach allowed (1)

IMSI attach/detach allowed

In Operation Mode I it is possible to have combined CS and PS side paging via SGSN. In Operation Mode II the combined paging procedure is not possible (and neither are combined attach procedures). Used only for the PS domain. NMO is part of PS CN domain specific NAS System information in System Information Block 1.

Network Mode of Operation I (0), Network Mode ofOperation II (1)

Network Mode ofOperation II (1)

The DRX cycle length used by UTRAN to count paging occasions for discontinuous reception./n(The duration of the DRX cycle is 2 <power> k frames, where 'k' is the used DRX cycle length coefficient for UTRAN.)

80 ms (3), 160 ms (4), 320 ms (5), 640 ms (6), 1280 ms (7), 2560 ms (8), 5120 ms (9)

The CELL UPDATE/URA UPDATE retransmission timer (MS timer). This parameter is part of System Information Block 1.

1000 ms (5), 1200 ms (6), 1400 ms (7), 1600 ms (8), 1800 ms (9), 2000 ms (10), 3000 ms (11), 4000 ms (12), 6000 ms (13), 8000 ms (14)

CELL UPDATE/URA UPDATE retransmission counter (MS counter). This parameter is part of System Information Block 1.

The timer for supervising successful connection establishment in case of an inter-RAT cell re-selection (MS timer).

The timer for supervising successful establishment of a physical channel (MS timer used in idle mode).

1...15 s, step 1 s

This parameter defines the maximum number of 'in sync' indications received from L1 during the establishment of a physical channel (UE counter used in idle mode)./nThis parameter is part of System Information Block 1.

1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7), 400 (8), 600 (9), 800 (10), 1000 (11)

The radio link failure timer (MS timer). This parameter is part of System Information Block 1.

0...15 s, step 1 s

This parameter defines the maximum number of successive "out of sync" indications received from L1 (MS counter). This parameter is part of System Information Block 1.

1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7)

The RRC connection re-establishment timer usedfor service-types allowing notably shorter re-establishmenttimes than the UE-timer T315. Currentlythis timer is used for CS service bearers only.UEs prior 3GPP REL6 use this timer also for supervisingthe RRC connection re-establishment ofstandalone (NAS) signaling connection towardsboth the CN domains.This parameter is part of System Information Block1.

0s (0), 2s (1), 4s (2), 6s (3), 8s (4), 12s (5), 16s (6),20s (7)

The RRC connection re-establishment timer for AM bearers (UE timer). This parameter is part of System Information Block 1.

0 s (0), 10 s (1), 30 s (2), 60 s (3), 180 s (4), 600 s (5), 1200 s (6), 1800 s (7)

This parameter defines the maximum number of successive "in sync" indications received from L1 while T313 is being activated (UE counter). This parameter is part of System Information Block 1.

1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7)



PtxSCCPCH1 0 dB

UTRAN_DRX_length 320 ms

T300 2000 ms

N300 0...7, step 1 3

T312 6 s

N312 4 (2)

0.5 s

640 ms












This is the transmission power of the S-CCPCH channel, which carries: - a PCH (containing PCCH), a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). Or alternatively (when standalone PCH is mapped to an another S-CCPCH) carries: - a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). In both cases the spreading factor of this S-CCPCH is 64 (60 ksps) and proposed default value is 0 dB. The transmission power value is relative to the CPICH transmission power.

-35...15 dB, step 0.1 dB

DownlinkInnerLoopPCStepSize

The DL inner loop PC step size is used in normal mode by the WCDMA BTS to calculate the power increase/decrease when receiving TPC commands.

0.5 dB (0), 1.0 dB (1), 1.5 dB (2), 2.0 dB (3)

The DRX cycle length used by UTRAN to count paging occasions for discontinuous reception./n(The duration of the DRX cycle is 2 <power> k frames, where 'k' is the used DRX cycle length coefficient for UTRAN.)

80 ms (3), 160 ms (4), 320 ms (5), 640 ms (6), 1280 ms (7), 2560 ms (8), 5120 ms (9)

The RRC CONNECTION REQUEST retransmission timer (MS timer)./nThis parameter is part of System Information Block 1.

100 ms (0), 200 ms (1), 400 ms (2), 600 ms (3), 800 ms (4), 1000 ms (5), 1200 ms (6), 1400 ms (7), 1600 ms (8), 1800 ms (9), 2000 ms (10), 3000 ms (11), 4000 ms (12), 6000 ms (13), 8000 ms (14)

RRC CONNECTION REQUEST retransmission counter (MS counter)./nThis parameter is part of System Information Block 1.

The timer for supervising successful establishment of a physical channel (MS timer used in idle mode).

1...15 s, step 1 s

This parameter defines the maximum number of 'in sync' indications received from L1 during the establishment of a physical channel (UE counter used in idle mode)./nThis parameter is part of System Information Block 1.

1 (0), 2 (1), 4 (2), 10 (3), 20 (4), 50 (5), 100 (6), 200 (7), 400 (8), 600 (9), 800 (10), 1000 (11)

InterFreqMeasRepInterval

This parameter determines the measurement reporting interval for periodical inter-frequency measurements.

0.5 s (2), 1 s (3), 2 s (4), 3 s (5), 4 s (6)




















AdjiQoffset1 0 dB

AdjiQoffset2 0 dB

AdjiQqualMin -18 dB

AdjiQrxlevMin -115 dBm

640 ms








HHoRscpThreshold -24~0 -9dbm

HHoRscpCancel -24~0 -9dbm





AdjgRxLevMinHO 8

AdjgRxLevMinHO 8

AdjgRxLevMinHO 8

AdditionWindow 4 dB

AdditionWindow 4 dB

AdditionWindow 4 dB



This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH RSCP of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.

-50...50 dB, step 1 dB

This parameter is used in the cell re-selection and ranking between WCDMA cells. The value of this parameter is subtracted from the measured CPICH Ec//No of the neighbour cell before the UE compares the quality measure with the cell re-selection//ranking criteria./nThis parameter is part of System Information Block 11&12.

-50...50 dB, step 1 dBThe minimum required quality

level in the cell (Ec//No)./nThis parameter is part of System Information Block 3.

-24...0 dB, step 1 dB


-115...-25 dBm, step 2 dBm



















-110...-47 dBm, step 1 dBm


-110...-47 dBm, step 1 dBm


-110...-47 dBm, step 1 dBm


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB



DropWindow 6 dB

DropWindow 6 dB

DropWindow 6 dB

0...2, step 0.1

AdditionTime 100 ms

DropTime 640 ms

AdjsDERR No (0), Yes (1) No

AdjsDERR No (0), Yes (1) No

AdjsQoffset1 0 dB

AdjsQoffset2 0 dB

PtxSCCPCH1 0 dB

PtxPrimaryCPICH 33 dBm

-25 dB

1...64, step 1 8

2 dB

2 dB

PtxPrimarySCH -3 dB

RACH_Tx_NB01min 0...50, step 1 0

RACH_Tx_NB01max 0...50, step 1 50

RACH_tx_Max 1...32, step 1 8

PtxSecSCH -3 dB

CNDomainVersion -

AdjiQoffset1 0 dB


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB


0...14.5 dB, step 0.5 dB

ActiveSetWeightingCoefficient

Active Set Weighting Coefficient (W) is used to weight either the measurement result of the best active set cell (M_best) or the sum of measurement results of all active set cells (M_sum) when the UE calculates the reporting range for the events 1A (cell addition) and 1B (dropping of cell). The formula is: W * M_sum + ( 1 - W )* M_best This parameter is part of System Information Block 11/12.

managedObject class="WCEL"中包含RtFmcsIdentifier的值对应到managedObject class="FMCS" version="×××" distName="PLMN-PLMN/RNC-××/FMCS-××模版中的ActiveSetWeightingCoefficient值。

When a monitored cell enters the reporting range (addition window), the cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to add the cell into the active set (event 1A). The length of this period is controlled by the parameter Addition Time. This parameter is part of System Information Block 11/12.


When an active set cell leaves the reporting range (drop window), the cell must continuously stay outside the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to remove the cell from the active set (event 1B). The length of this period is controlled by the parameter Drop Time. This parameter is part of System Information Block 11/12.


This parameter indicates whether the neighbouring cell is forbidden to affect the reporting range (addition/drop window) calculation, if it belongs to the active set.

This parameter indicates whether the neighbouring cell is forbidden to affect the reporting range (addition/drop window) calculation, if it belongs to the active set.


-50...50 dB, step 1 dB


-50...50 dB, step 1 dB

This is the transmission power of the S-CCPCH channel, which carries: - a PCH (containing PCCH), a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). Or alternatively (when standalone PCH is mapped to an another S-CCPCH) carries: - a FACH (containing DCCH/BCCH/CCCH) and a FACH (containing DTCH). In both cases the spreading factor of this S-CCPCH is 64 (60 ksps) and proposed default value is 0 dB. The transmission power value is relative to the CPICH transmission power.

-35...15 dB, step 0.1 dB

This is the transmission power of the primary common pilot channel. The P-CPICH physical channel carries the common pilots of the cell, which is defined in the cell setup. The transmission power of the CPICH physical channel defines the actual cell size, which means that the power is determined by radio network planning. This parameter is used, for example, for neighbour measurements - critical for the network performance. The default value is 5-10% of the maximum transmitting power of WCDMA BTS, which can be, for example, 43 dBm/carrier. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. Note: The cell is blocked if the WCDMA BTS does not support the used value. Typical supported range is (Cell max power - 18dB)..(Cell max power - 3dB). This parameter is part of System Information Block 5.

-10...50 dBm, step 0.1 dBm

PRACHRequiredReceivedCI

This UL required received C/I value is used by the UE to calculate the initial output power on PRACH according to the Open loop power control procedure. This parameter defines the value of the IE Constant value, which is part of System Information Block 5. The value of the parameter depends on the propagation channel. Note: If the operator perceives a difference in DL and UL linklosses, for example when MHA is used in BTS, then this parameter can be used to compensate for it in the power of the first transmitted preamble on the PRACH.

-35...-10 dB, step 1 dB

PRACH_preamble_retrans

The maximum number of preambles allowed in one preamble ramping cycle. PRACH Preamble Retrans Max is part of "PRACH power offset" which is part of "PRACH system information list" which is part of System Information Block 5&6.

PowerRampStepPRACHpreamble

The power ramp step on PRACH preamble when no acquisition indicator (AI) is detected by the UE. This parameter is part of System Information Block 5.

1...8 dB, step 1 dB

PowerOffsetLastPreamblePRACHmessage

The power offset between the last transmitted preamble and the control part of the PRACH message (added to the preamble power to receive the power of the message control part). This parameter is part of System Information Block 5.

-5...10 dB, step 1 dB

This is the transmission power of the primary synchronisation channel. The power level is relative to the [FDD-primary CPICH power]. The primary SCH consists of a modulated code 256 chips in length: the Primary Synchronisation Code (PSC) transmitted once every slot. The PSC is the same for every cell in the system, and it enables the downlink slot synchronisation in the cell. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.

-35...15 dB, step 0.1 dB

In case that a negative acknowledgement has been received by UE on AICH a backoff timer TBO1 is started to determine when the next RACH transmission attempt will be started. The backoff timer TBO1 is set to an integer number NBO1 of 10 ms time intervals, randomly drawn within an interval 0 <= NB01min <= NBO1 <= NB01max (with uniform distribution). After TB01 has been expired, the next RACH attempt will be started. NB01min and NB01max may be set equal when a fixed delay is desired, and even to zero when no delay other than the one due to persistency is desired. NB01min is given as an integer between 0 and 50 which gives the Lower bound of the waiting time in 10ms steps. NB01min is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of System Information Block 5&6.

In case that a negative acknowledgement has been received by UE on AICH a backoff timer TBO1 is started to determine when the next RACH transmission attempt will be started. The backoff timer TBO1 is set to an integer number NBO1 of 10 ms time intervals, randomly drawn within an interval 0 <= NB01min <= NBO1 <= NB01max (with uniform distribution). After TB01 has been expired, the next RACH attempt will be started. NB01min and NB01max may be set equal when a fixed delay is desired, and even to zero when no delay other than the one due to persistency is desired. NB01max is given as an integer between 0 and 50 which gives the Upper bound of the waiting time in 10ms steps. NB01max is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of SIB5/6. This parameter is part of System Information Block 5.

Maximum number of RACH preamble cycles defines how many times the PRACH pre-amble ramping procedure can be repeated before UE MAC reports a failure on RACH transmission to higher layers. Maximum number of RACH preamble cycles is part of "RACH transmission parameters" which is part of "PRACH system information list" which is part of SIB5/6. This parameter is part of System Information Block 5.

This is the transmission power of the secondary synchronisation channel related to the Primary CPICH transmission power. The secondary SCH consists of repeatedly transmitting a length 15 sequence of modulated codes 256 chips in length. These are the Secondary Synchronisation Codes (SSC), transmitted in parallel with the primary SCH. This sequence on the secondary SCH enables the downlink frame synchronisation, and indicates, to which code group the cell downlink scrambling code belongs. Each SSC is chosen from a set of 16 different codes 256 chips in length. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.

-35...15 dB, step 0.1 dB

The code that uniquely identifies the Release version of the Core Network connected to the RNC.

R99 (1), Rel4 (2), Rel5 (3), Rel6 (4)


-50...50 dB, step 1 dB



AdjsQoffset2 0 dB

0.5 s

0.5 s

ReplacementWindow 2 dB

ReplacementTime 100 ms

MaxActiveSetSize 2...3, step 1 3

AdjsQoffset1 0 dB

AdjsQoffset2 0 dB

Sintrasearch 10db

Sintersearch 8 dB

0.5 s

0.5 s

ReplacementWindow 2 dB

0...2, step 0.1 0

CellBarred Not barred

Allowed

Tbarred 40 s

ToCellFACHinTest No (0), Yes (1) Yes (1)



-50...50 dB, step 1 dB

AdditionReportingInterval

When a monitored cell enters the reporting range and triggers event 1A (cell addition), the UE transmits a Measurement Report to the RNC. If the RNC is not able to add the monitored cell to the active set, the UE continues reporting after the initial report by reverting to periodical measurement reporting. The parameter Addition Reporting Interval determines the interval between periodical measurement reports when such reporting is triggered by the event 1A. This parameter is part of System Information Block 11/12.

gui ==> internalNo periodical reporting ==> 00.25 s. Not allowed ==> 10.5 s ==> 21 s ==> 32 s ==> 44 s ==> 58 s ==> 616 s ==> 7

ReplacementReportingInterval

When the number of cells in the active set has reached the maximum, and a monitored cell becomes better than an active set cell, the UE transmits a When the number of cells in the active set has reachedthe maximum, and a monitored cell becomes betterthan an active set cell, the UE transmits a MeasurementReport to the RNC in order to replace the active cellwith the monitored cell (event 1C). If the RNC is notable to replace the active cell with the monitored cell,the UE continues reporting after the initial report byreverting to periodical measurement reporting. Theparameter Replacement Reporting Interval determinesthe interval of periodical measurement reports whensuch reporting is triggered by the event 1C.


When the number of cells in the active set has reached the maximum specified by the parameter MaxActiveSetSize and a monitored cell becomes better than an active set cell, the UE transmits a Measurement Report to the RNC in order to replace the active cell with the monitored cell (event 1C). The parameter Replacement Window determines the margin by which the CPICH Ec/No measurement result of the monitored cell (MNew) must exceed the CPICH Ec/No measurement result of the an active set cell (MInAS) before the UE can send the event 1C triggered Measurement Report to the RNC: MNew >= MInAs + ReplacementWindow / 2 This parameter is part of System Information Block 11/12.

0...7.5 dB, step 0.5 dB

When the number of cells in the active set has reachedthe maximum, and a monitored cell enters the reportingrange (replacement window), the monitored cell mustcontinuously stay within the reporting range for a givenperiod of time before the UE can send a MeasurementReport to the RNC in order to replace an active set cellwith the monitored cell (event 1C). The length of thisperiod is controlled by the parameter ReplacementTime.

gui ==> internal0 ms ==> 010 ms ==> 120 ms ==> 240 ms ==> 360 ms ==> 480 ms ==> 5100 ms ==> 6120 ms ==> 7160 ms ==> 8200 ms ==> 9240 ms ==> 10320 ms ==> 11640 ms ==> 121280 ms ==> 132560 ms ==> 145000 ms ==> 15

This parameter determines the maximum number of cells which can participate in a soft/softer handover. Reporting deactivation threshold indicates the maximum number of cells allowed in the active set in order for the event 1A to trigger. The RNC calculates the deactivation threshold from the parameter MaxActiveSetSize: Reporting Deactivation Threshold = MaxActiveSetSize - 1 Reporting Deactivation Threshold parameter is part of System Information Block 11/12. Replacement activation threshold information element indicates the minimum number of cells allowed in the active set in order for the event 1C to trigger. The threshold equals to the maximum size of the active set which is controlled with the parameter MaxActiveSetSize. Replacement Activation Threshold parameter is part of System Information Block 11/12.


-50...50 dB, step 1 dB


-50...50 dB, step 1 dB

The threshold for intra-frequency measurements, and for the HCS measurement rules./nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.


The threshold for inter-frequency measurements, and for the HCS measurement rules. /nNote: If no threshold is given, MS performs measurements./nThis parameter is part of System Information Block 3.


AdditionReportingInterval

When a monitored cell enters the reporting range and triggers event 1A (cell addition), the UE transmits a Measurement Report to the RNC. If the RNC is not able to add the monitored cell to the active set, the UE continues reporting after the initial report by reverting to periodical measurement reporting. The parameter Addition Reporting Interval determines the interval between periodical measurement reports when such reporting is triggered by the event 1A. This parameter is part of System Information Block 11/12.


ReplacementReportingInterval

When the number of cells in the active set has reached the maximum, and a monitored cell becomes better than an active set cell, the UE transmits a When the number of cells in the active set has reachedthe maximum, and a monitored cell becomes betterthan an active set cell, the UE transmits a MeasurementReport to the RNC in order to replace the active cellwith the monitored cell (event 1C). If the RNC is notable to replace the active cell with the monitored cell,the UE continues reporting after the initial report byreverting to periodical measurement reporting. Theparameter Replacement Reporting Interval determinesthe interval of periodical measurement reports whensuch reporting is triggered by the event 1C.


When the number of cells in the active set has reached the maximum specified by the parameter MaxActiveSetSize and a monitored cell becomes better than an active set cell, the UE transmits a Measurement Report to the RNC in order to replace the active cell with the monitored cell (event 1C). The parameter Replacement Window determines the margin by which the CPICH Ec/No measurement result of the monitored cell (MNew) must exceed the CPICH Ec/No measurement result of the an active set cell (MInAS) before the UE can send the event 1C triggered Measurement Report to the RNC: MNew >= MInAs + ReplacementWindow / 2 This parameter is part of System Information Block 11/12.

0...7.5 dB, step 0.5 dB

ActiveSetWeightingCoefficient

Active Set Weighting Coefficient (W) is used to weight either the measurement result of the best active set cell (M_best) or the sum of measurement results of all active set cells (M_sum) when the UE calculates the reporting range for the events 1A (cell addition) and 1B (dropping of cell). The formula is: W * M_sum + ( 1 - W )* M_best This parameter is part of System Information Block 11/12.

When the number of cells in the active set has reached the maximum, and a monitored cell enters the reporting range (replacement window), the monitored cell must continuously stay within the reporting range for a given period of time before the UE can send a Measurement Report to the RNC in order to replace an active set cell with the monitored cell (event 1C). The length of this period is controlled by the parameter Replacement Time. This parameter is part of System Information Block 11/12.

Defines whether the cell is barred or not./nA barred cell is a cell where a UE is not allowed to camp on. Emergency calls shall be allowed in all cells whose barred status is 'not barred'. When cell status is 'barred', the UE is not permitted to select//re-select the cell, not even for emergency calls./nThis parameter is part of System Information Block 3.

Barred (0), Not barred (1)

IntraFreq_Cell_Reselect_Ind

Defines whether intra-frequency cell re-selection is allowed or not when the cell is barred./nWhen a cell's status is 'barred', the UE is not permitted to select//re-select this cell, except in some cases for an emergency call. If the 'Intra-frequency cell re-selection indicator' is set to value 'allowed', the UE may select another cell on the same frequency if selection//re-selection criteria are fulfilled. If the 'Intra-frequency cell re-selection indicator' is set to 'not allowed' the UE shall not re-select even a different cell on the same frequency as the barred cell. For emergency call, the Intra-frequency cell re-selection indicator IE' shall be ignored. 'Intra-frequency cell re-selection indicator' is part of SIB3//4 in the case the 'cell barred' indicator is true./nThis parameter is part of System Information Block 3.

Allowed (0), Not allowed (1)

When the cell is barred, the UE must check between the time interval ‘Cell barred period’, whether the status of the barred cell has changed./nThis parameter is part of the System Information Block 3.

10 s (0), 20 s (1), 40 s (2), 80 s (3), 160 s (4), 320 s (5), 640 s (6), 1280 s (7)

When the test timer expires, the UE is switched to Cell_FACH state when the value of the parameter ToCellFACHinTest is 'Yes'. If the ToCellFACHinTest parameter value is 'No', an Iu Release procedure is initiated in the Cell_DCH state, and the UE is switched directly to idle mode.0 (No), 1 (Yes)





2000 ms

MSActivitySupervision 29 minutes

0(0ms)

30 min

3s

3s


InactivityTimerDownlinkDCH128InactivityTimerDownlinkDCH16InactivityTimerDownlinkDCH256InactivityTimerDownlinkDCH32InactivityTimerDownlinkDCH320InactivityTimerDownlinkDCH384InactivityTimerDownlinkDCH64InactivityTimerDownlinkDCH8InactivityTimerUplinkDCH128InactivityTimerUplinkDCH16InactivityTimerUplinkDCH256InactivityTimerUplinkDCH32InactivityTimerUplinkDCH320InactivityTimerUplinkDCH384InactivityTimerUplinkDCH64SignallingLinkInactivityTimerCellDCHtestTmrMACdflowthroughputTimetoTriggerEDCHMACdFlowThroughputTimetoTrigger

The time indicating how long the radio and transmission resources are reserved after silence detection on downlink DCH before release procedures. Default values: 8 kbps: 5 s 16 kbps: 5 s 32 kbps: 5 s 64 kbps: 3 s 128 kbps: 2 s 256 kbps: 2 s 320 kbps: 2 s 384 kbps: 2 s

0...20 s, step 1 s

UL_DL_activation_timer

This timer is used on MAC -c to detect idle periods on data transmission (NRT RBs and SRBs) for the UE, which is in Cell_FACH state. Based on this timer the MAC -c shall give the No_Data indication to the RRC, which further can change the state of the RRC from Cell_FACH state to the Cell_PCH state (or URA_PCH state).

50...10000 ms, step 50 ms

This timer is used in RRC states Cell_PCH and URA_PCH for supervising the inactivity of NRT RAB(s).If the parameter value is set to zero, state transition to Cell_PCH / URA_PCH state is not allowed. When inactivity is detected in Cell_FACH state, the UE will be switched to the idle mode. Range and step: 0 ... 1440 min, step 1 min

0...1440 minutes, step 1 minutesTrafVolThresholdULLo

wTrafVolThresholdDLLowNASsignVolThrULNASsignVolThrDL

This parameter defines, in bytes, the threshold of data in the RLC buffers of SRB0, SRB1, SRB2, SRB3, SRB4 and all NRT RBs that triggers the uplink traffic volume measurement report, when the UE is in Cell_FACH state. Otherwise, UE sends data on RACH.This parameter is sent to the UE using an RRC:MEASUREMENT CONTROL message.

gui ==> internal8 bytes ==> 816 bytes ==> 1632 bytes ==> 3264 bytes ==> 64128 bytes ==> 128256 bytes ==> 256512 bytes ==> 5121 KB ==> 1024

TrafVolTimeToTriggerULTrafVolTimeToTriggerDL

This parameter defines, in ms, the period of time between the timing of event detection and the timing ofsending a traffic volume measurement report.This parameter is sent to the UE using an RRC: MEASUREMENT CONTROL message.

gui ==> internal0 ms ==> 010 ms ==> 1020 ms ==> 2040 ms ==> 4060 ms ==> 6080 ms ==> 80100 ms ==> 100120 ms ==> 120160 ms ==> 160200 ms ==> 200240 ms ==> 240320 ms ==> 320640 ms ==> 6401280 ms ==> 12802560 ms ==> 25605000 ms ==> 5000

CellReselectionObservingTime

The timer is set when the first Cell Update message due to 'cell reselection' is received while UE is in CELL_FACH or CELL_PCH state. In expiry of the timer, the counter MaxCellReselections is reset. Below is an example of target RRC state selection when value 3 is used for MaxCellReselections: Velocity Cell radius Cell Update Target RRC state km/h km frequency 50 10 12 minutes CELL_PCH 50 20 24 minutes CELL_PCH 75 10 8 minutes URA_PCH 75 20 16 minutes CELL_PCH 100 10 6 minutes URA_PCH 100 20 12 minutes CELL_PCH

1...60 min, step 1 minEDCHMACdFlowThro

ughputAveWinMACdflowthroughputAveWin

This parameter defines the size of the sliding averaging window for the throughput measurement of the E-DCH NRT MAC-d flow. The throughput measurement measures the number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window.The value 0 of the parameter means that the E-DCH MAC-d flow throughput measurement is not performed.

0.5...10 s, step 0.5 sinternal_value = gui_value * 2

EDCHMACdFlowThroughputAveWinMACdflowthroughputAveWin

This parameter defines the size of the sliding averaging window for the throughput measurement of the E-DCH NRT MAC-d flow. The throughput measurement measures the number of bits transmitted by the E-DCH MAC-d flow during the sliding measurement window.The value 0 of the parameter means that the E-DCH MAC-d flow throughput measurement is not performed.

0.5...10 s, step 0.5 sinternal_value = gui_value * 2



Tcell -

PriScrCode 0...511, step 1 -

LAC -

SAC - -

RAC 0...255, step 1 -

Cid -

UARFCN -

Qhyst1PCH 0...40,step 1 -

Qhyst1FACH 0...40,step 1 -

Qhyst2PCH 0...40,step 1 -

Qhyst2FACH 0...40,step 1 -

TreselectionFACH 0...6.2,step 0.2 -

TreselectionPCH 0...31,step 1 -

GsmMeasRepInterval 0.5 s (2), 1 s (3), -

GsmMeasAveWindow 1...32 -

GsmMinHoInterval 1..60 -

MaxNbrOfHSSCCHCod 1...3 -

GsmHandoverAMR

GsmHandoverNrtPS No (0), Yes (1)

PrxMaxTargetBTS 0...30 6 dB

MaxNumberEDCHCell 1...20 72

[-8.2..+17.3] 4dB

[-8.2..+17.3] 6dB

[-8.2..+17.3] 13dB

Each cell in a BTS uses a System Frame Number (SFN) counter, which is the BTS Frame Number (BFN) counter delayed by a number of chips defined by the value of Tcell. Tcell is used for defining the start of SCH, CPICH, Primary CCPCH and DL Scrambling Code(s) in a cell relative to BFN. The main purpose is to avoid having overlapping SCHs in different cells belonging to the same BTS. An SCH burst is 256 chips long. The values can be chosen as follows: 0 chips for the 1st cell of the BTS, 256 chips for the 2nd cell of the BTS, 512 chips for the 3rd cell of the BTS, etc. Note: Changing the parameter value will start the cell shutdown procedure in the BTS.

0 chips (0), 256 chips (1), 512 chips (2), 768 chips (3), 1024 chips (4), 1280 chips (5), 1536 chips (6), 1792 chips (7), 2048 chips (8), 2304 chips (9)

Identifies the downlink scrambling code of the Primary CPICH (Common Pilot Channel) of the Cell. Note: Changing the parameter value will start the cell shutdown procedure in the BTS. This parameter is part of System Information Block 11.

This parameter contains the Location area code (LAC) of a WCDMA cell. The coding of the Location area code (two octets) is the responsibility of administration. LAI (Location Area Identification) consists of PLMNid and LAC. If LAI has to be deleted, LAC is set as 0xFFFE. This parameter is also part of System Information Block 1 and known as IE: GSM-MAP NAS system information.

1...65535, step 1

The Service Area Identifier (SAI) identifies an area consisting of one or more cells which belong to the same Location Area (LAI). The Service Area Identifier is composed of the PLMN Identifier, the Location Area Code (LAC) and the Service Area Code (SAC).

The routing area code determines the Routing area within the location area to which the cell belongs to. It is used only for PS services (part of PS domain specific NAS system information in SIB1). Routing area identification (RAI) consists of LAI and RAC, LAI consists of PLMNid and LAC. This parameter is part of System Information Block 1.

The parameter identifies the cell within a RNC. This parameter is part of System Information Block 3.

1...65535, step 1

The carrier frequency is designated by the parameter UTRA Absolute Radio Frequency Channel Number (UARFCN). This parameter defines the downlink channel number. The uplink channel number is calculated by the RNC based on a duplex distance used in the RF band. The relation between UARFCN (Nd) and the corresponding carrier frequency (Fdownlink [MHz]) in RF bands I, II and V is defined with the following equations: Fdownlink = 0.2 * Nd MHz Nd = 5 * Fdownlink The relation between the UARFCN (Nd) additional channel and the corresponding carrier frequency (Fdownlink [MHz]) in RF band II is defined with the following equations: Fdownlink = (1850.1 + 0.2 * Nd) MHz Nd = 5 * (Fdownlink - 1850.1 MHz) The relation between the UARFCN (Nd) additional channel and the corresponding carrier frequency (Fdownlink [MHz]) in RF band V is defined with the following equations: Fdownlink = (670.1 + 0.2 * Nd) MHz Nd = 5 * (Fdownlink - 670.1 MHz) Downlink RF band I is 2110 - 2170 MHz. Downlink RF band II is 1930 - 1990 MHz. Downlink RF band V is 869 - 894 MHz. Allowed channel numbers (Nd) in RF band I are: 10562 - 10838. Allowed channel numbers (Nd) in RF band II are: 9663 - 9712, 9763 - 9812, 9888 - 9937. Allowed additional channel numbers (Nd) in RF band II are: 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687. Allowed channel numbers (Nd) in RF band V are: 4357 - 4458. Allowed additional channel numbers (Nd) in RF band V are: 1007, 1012, 1032, 1037, 1062, 1087. The duplex distance is 190 MHz in RF band I, 80 MHz in RF band II and 45 MHz in RF band V. This parameter is part of System Information Block 5.

0...16383, step 1

The parameter is used for cell selection and reselectionin Cell_PCH/URA_PCH.Qhyst1PCH is used for TDD and GSM cells, and forFDD cells when cell selection and re-selectionquality measure is set to CPICH RSCP.This is hysteresis between WCDMA and GSMcells. Hysteresis is not needed because negativeoffset is used.

The parameter is used for cell selection and reselectionin Cell_FACH.The parameter is used for TDD and GSM cells, andfor FDD cells when cell selection and re-selectionquality measure is set to CPICH RSCP.This is hysteresis between WCDMA and GSMcells. Hysteresis is not needed because negativeoffset is used.

The parameter is used for cell selection and reselectionin Cell_PCH/URA_PCH.The parameter is used for FDD cells when cellselection and re-selection quality measure is set toCPICH Ec/No.2dB hysteresis between WCDMA cells can be usedin urban environment to avoid ping-pong.0dB hysteresis can be used in areas of high mobilitylike highways.

The parameter is used for FDD cells when cellselection and re-selection The parameter is usedfor cell selection and re-selection in Cell_FACH.The parameter is used for FDD cells when cellselection and re-selection quality measure is set toCPICH Ec/No.2dB hysteresis between WCDMA cells can be usedin urban environment to avoid ping-pong. 0dB hysteresiscan be used in areas of high mobility likehighways.

This parameter is used for cell selection and reselectionin Cell_FACH.The UE triggers the reselection of a new cell if thecell reselection criteria are fulfilled during the timeinterval TreselectionFACH.The reselection time of 2s may avoid too many cellreselections between cells and hence LA/RAupdates when crossing the LA/RA border. Thus,there are less signalling and less call failures at theLA/RA border due to the LA/RA update. The reselectiontime of 0s can be used in areas of highmobility, such as highways.

selectionin Cell_PCH/URA_PCH.The UE triggers the reselection of a new cell if thecell reselection criteria are fulfilled during the timeinterval TreselectionPCH.The reselection time of 2s may avoid too many cellreselections between cells and hence LA/RAupdates when crossing the LA/RA border. Thus,there are less signalling and less call failures at theLA/RA border due to the LA/RA update. The reselectiontime of 0s can be used in areas of highmobility, such as highways.

This parameter determines the measurementreporting interval for periodical inter-RAT (GSM)measurements.

This parameter determines the maximum numberof periodical inter-RAT (GSM) measurementreports (maximum size of the sliding averagingwindow) from which the RNC calculates theaveraged GSM RSSI values for the handoverdecision algorithm.

This parameter determines the minimum intervalbetween a successful inter-RAT handover fromGSM to UTRAN and the following inter-RAThandover attempt back to GSM related to the sameRRC connection.

This parameter defines the maximum number ofHS-SCCH codes (SF 128) that can be reserved inone cell.More than one HS-SCCH code can be used if theHSDPA code multiplexing functionality is in use.The actual number of reserved codes depends onfor example HSDPA capabilities and HSDPA codemultiplexing support (RNC and BTS).

This parameter indicates whether an inter-RAThandover to GSM is allowed for circuit switched(CS) voice services. The alternative values of theparameter are the following:- No; handover to GSM is not allowed for CS voiceservices. The handover is also prohibited if a CSvoice service is a part of multiservice.- Yes; handover to GSM is allowed for CS voice services.In case of multiservice, a handover to GSMmust be allowed for all CS and PS services whichparticipate in the multiservice before the handoveris possible.- Priority; handover to GSM is allowed for CS voiceservices. The handover is also allowed if a CS voiceservice is a part of multiservice.

No (0), Yes (1), Priority (2)

This parameter indicates whether an inter-RAThandover (cell change) to GSM/GPRS is allowedfor non-real time packet switched (PS) dataservices in CELL_DCH state of connected mode.The alternative values of the parameter are the following:- No; cell change to GSM/GPRS is not allowed fornon-real time PS data services. The handover/cellchange to GSM/GPRS is also prohibited if a nonrealtime PS data service is a part of multiservice.- Yes; cell change to GSM/GPRS is allowed fornon-real time PS data services. In case of multiservice,a handover/cell change to GSM/GPRS mustbe allowed for all CS and PS services which participatein the multiservice before the handover/cellchange is possible.The parameters GsmHandoverAMR and/orGsmHandoverCS for CS data/voice services canoverrule the value of the parameter GsmHandoverNrtPSin case of multiservice. If either CSvoice and/or data services are prioritized, the RNCshall execute the handover to GSM even if the cellchange to GSM/GPRS is not allowed for non-realtime PS data services.

HHoRscpFilterCoefficient

In the CELL_DCH state the UE physical layer measurementperiod for intra-frequency CPICH RSCPmeasurements is 200 ms. The Filter Coefficientparameter controls the higher layer filtering ofphysical layer CPICH RSCP measurements beforethe event evaluation and measurement reporting isperformed by the UE. The CPICH RSCP measurementreports can be used to trigger off inter-frequencyor inter-RAT (GSM) measurements for thepurpose of hard handover.The higher layer filtering is described in 3GPP TS25.331 RRC Protocol Specification, section FilterCoefficient.

Filtering period of 200 ms (0), Filtering periodapproximates 300 ms (1), Filtering period approximates400 ms (2), Filtering period approximates600 ms (3), Filtering period approximates 800 ms(4), Filtering period approximates 1100 ms (5), Filteringperiod approximates 1600 ms (6)

The maximum target for received total wide band

power in the cell for BTS packet schedulingThis parameter determines the

maximum numberof E-DCH allocations in the cell.INITSIRTARGET(2-

antenna and MinSF=2SF4)

initial Uplink SIR Target for RABs

NITSIRTARGET(2-antenna and

MinSF<2SF4)

initial Uplink SIR Target for RABs

MAXSIRTARGET(2-antenna and

MinSF=2SF4)

Max Uplink SIR Target for RABs



[-8.2..+17.3] 15dB

MINSIRTARGET Min Uplink SIR Target for RABs [-8.2..+17.3] 0

low to 16% 1%

low to 16% 1%

CQI Feedback Cycle 4ms

MAXSIRTARGET(2-antenna and

MinSF<2SF4)

Max Uplink SIR Target for RABs

BLER targets for E-DCH 10ms

BLER targets for E-DCH 2ms

is determining the CQI report transmissions on the HS-

DPCCH



NSN

RU20

Mapping Rule Remark

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the Huawei baseline value.




Use the NSN value.

Locate the NSN value in the following order:WCEL > the last ADJG > the HopgIdentifier value > the HOPG value > the AdjgQrxlevMin value

NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.

Huawei NSN RESERVED reserved NOT_RESERVED Not reserved Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1 Huawei NSN NOT_BARRED 0 BARRED 1





Huawei NSN NOT_BARRED Not barred BARRED barred Huawei NSN ALLOWED Allowed NOT_ALLOWED Not allowed Huawei NSN DN Ns

Huawei NSNMaxTxPower+HspaPower<==>PtxMaxHSDPA

Locate the NSN value in the following order:WCEL > the RtFmciIdentifier value > the FMCI value > the InterFreqMeasRepInterval value Huawei NSN D500 0.5 s D1000 1 s ……………………….. D(N*1000) N s

Use the value 0.

Use the value 0.

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoTimeHysteresis value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancelTime valueIf the NSN value is larger than the Huawei value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshol value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshol value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel valueUse the value 0.

Use the value 0.

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoTimeHysteresis value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancelTime valueIf the NSN value is larger than the Huawei value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms

NSN does not have such a parameter.

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value






Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -24. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHEcNo valueIf the NSN value is Disabled, use the value -22. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoEcNoCancel value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -115. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpThreshold value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the GSMcauseCPICHrscp valueIf the NSN value is Disabled, use the value -113. Otherwise, locate another NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the HHoRscpCancel value

Locate the NSN value in the following order:WCEL > the last ADJG > the RtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value

Locate the NSN value in the following order:WCEL > the last ADJG > the NRtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value

Locate the NSN value in the following order:WCEL > the last ADJG > the NRtHopgIdentifier value > the HOPG value > the AdjgRxLevMinHO value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionWindow value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionWindow value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the AdditionWindow value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropWindow value

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropWindow value

Locate the NSN value in the following order:WCEL > the NrtFmcsIdentifier value > the FMCS value > the DropWindow value NSN does not have

such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the AdditionTime value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms

Locate the NSN value in the following order:WCEL > the RtFmcsIdentifier value > the FMCS value > the DropTime value Huawei NSN D0 0 ms D10 10 ms ……………………… D(N) N ms




Use the NSN value.

Use the NSN value.


Use the NSN value.


Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.


NSN does not have such a parameter.The NSN value is 3 as well.

Huawei NSN ALLOWED IMSI attach/detach allowed NOT_ALLOWED IMSI attach/detach not allowed

HUAWEI NSNMODE1 Network Mode of Operation I MODE2 Network Mode of Operation II

Huawei NSN 3 80 ms 4 160 ms 5 320 ms 6 640 ms 7 1280 ms 8 2560 ms 9 5120 ms

Huawei NSN D1000 1000 ms D1200 1200 ms…………………………….. D(N) N ms

If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.

Huawei NSN D1 0 D2 1 D4 2 D10 3 D20 4 D50 5 D100 6 D200 7 D400 8 D600 9 D800 10 D1000 11

If the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.

Huawei NSN D50 N<=5 D100 6 D200 7 The value D12 is recommended.The value D30 is recommended.











Use the NSN value.
















NSN does not have such a parameter.If the NSN value is larger than

the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value. Huawei NSN 3 80 ms 4 160 ms 5 320 ms 6 640 ms 7 1280 ms 8 2560 ms 9 5120 ms

Huawei NSN DN 100ms<=N<=2000ms D2000 N>2000msIf the NSN value is larger than the Huawei baseline value, use the NSN value. Otherwise, use the Huawei baseline value.


Use the value 0.

Use the value 0.



























Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQoffset1 value

Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQoffset2 value

Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQqualMin value

Locate the NSN value in the following order:WCEL > ADJI > the RtHopgIdentifier value > the HOPI value > the AdjiQrxlevMin valueUse the value 0.

Use the value 0.














Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.


Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.




NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.

NSN does not have such a parameter.NSN does not have such a parameter.

Huawei NSNNOT_AFFECT NO AFFECT YES Huawei NSNNOT_AFFECT NO AFFECT YES

Locate the NSN value in the following order:WCEL > ADJS > the RtHopsIdentifier value > the HOPS value > the AdjsQoffset1 value

Locate the NSN value in the following order:WCEL > ADJS > the RtHopsIdentifier value > the HOPS value > the AdjsQoffset2 value


For connected-state-related parameters, Huawei baseline values are recommended but the multi-carrier policy must be considered as well when Huawei baseline values are used.































NSN does not have such a parameter.NSN does not have such a parameter.NSN does not have such a parameter.

Because the NSN value is smaller than the Huawei value, triggering event 1A or 1C is relatively difficult for Huawei. For event 1A or 1C, the Huawei buffering mechanism is different from the NSN buffering mechanism. If the NSN value is used, the number of times event 1A or 1C is reported will increase, leading to the increased call drop rate.





The NSN value is 3 as well.





NSN does not have such a parameter.Use the Huawei baseline

value.Use the Huawei baseline value.






NSN value is 0 as well.





For state transition, the NSN mechanism is different from the Huawei mechanism. The NSN mechanism imposes restrictions on the user plane and control plane. However, the Huawei baseline value is recommended.

























InterFreqCSThd2DEcN0 + 3

InterFreqCSThd2DRSCP + 3















InterFreqR99PsThd2DEcN0 + 3


InterFreqR99PsThd2DEcN0 + 3


InterFreqR99PsThd2DRSCP + 3


InterFreqR99PsThd2DRSCP + 3




Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.

Use the NSN value.







Huawei NSNCHIP0 0chipsCHIP256 256chipsCHIP512 512chipsCHIP768 768chipsCHIP1024 1024 chipsCHIP1280 1280chipsCHIP1536 1536chipsCHIP1792 1792chipsCHIP2048 2048chipsCHIP2304 2304chips

Before using the NSN value, turn on the SIB4 switch by running the following command:MOD UCELLSIBSWITCH: CellId=***, SibCfgBitMap=SIB4-1;






HUAWEI NSN D500 0.5SD1000 1SD2000 2SD3000 3SD4000 4SHUAWEI<==>GsmMeasAveWindow*GsmMeasRepInterval

HUAWEI NSN HO_INTER_RAT_CS_OUT_SWITCH-0 NOHUAWEI NSN HO_INTER_RAT_PS_OUT_SWITCH-0 NO

HUAWEI NSN0 Filtering period approximates 200 ms

Use Huawei suggestion：122（4dB）

May be further Optimized to

103（2.1dB）. Need validation

in several networks.

Use Huawei suggestion：182（10dB）







Use the NSN value.

Use Huawei suggestion（4dB）REFETFCIIDX1=4, REFETFCIIDX2=54, REFETFCIPO1=PO_24/15,

REFETFCIPO2=PO_106/15,Use Huawei suggestion: ERGCH2INDSTPTHS=16, ERGCH3INDSTPTHS=13

wcdma ran13 parameter mapping(ericsson w10,nsn ru10, ru20, alu ua5.1)

Documents