trunnion mounted ball valve - spx · pdf file2 spx flow trunnion mounted ball valve spx flow,...

Trunnion Mounted Ball ValveMAN UAL CONTE NTS

2

SPX FLOW Trunnion Mounted Ball ValveSPX FLOW, Inc. offers both a two piece and a three piece bolted body design

trunnion mounted ball valve with either an external or internal trunnion bearing.

This ball valve provides an attractive and cost effective solution for bubble-tight

shut off requirements in many oil and gas applications.

PROD UCT B E N E FITS AN D FEATU R E S:

Two and Three Piece Bolted Body

The SPX FLOW ball valve offers both a two piece and a three piece bolted

body design. The external and internal trunnion bearings reduce the sealing

forces and associated high torque, as well as the seat wear of fl oating ball valve

designs.

Trunnion Mounted Ball

The trunnions are precisely fi tted to the ball and TFE lined bearing connected to

the body. The bearings absorb the side load generated by pressure acting on the

ball. This design feature provides consistent torque and the exact location and

support of the ball.

Double Block and Bleed

The valve possesses double block and bleed capability where the body cavity

can be vented with the ball in the fully open or closed position. Vent fi ttings in

the upper body and a combination vent / drain fi tting in the bottom of the body

provides this functionality.

Positive Stem Sealing Using Multiple Seals

The SPX FLOW ball valve standard stem seal design uses three seals to ensure

a positive seal. The primary stem seal is fi re-safe graphite packing. Additionally,

two additional elastomer o-ring seals above the primary seal are used.

Emergency Seat Sealant Injection

Under standard operating conditions the SPX FLOW ball valve does not require

any lubrication or routine maintenance. However, in the event the seat seal is

damaged during operation, an emergency sealant injection system is provided as

a standard on all valves. Sealant can be injected directly to the seat sealing area

to effect a temporary emergency seal.

Anti-static Continuity for all Components

The SPX FLOW ball valve is designed to provide electrical continuity of all valve

components to prevent the buildup of a static charge on internal components.

Electrical continuity between parts such as the body and ball is ensured

using springs.

Meets API 6D

The through conduit full bore API 6D design assures unrestricted fl ow

and allows both pigging and hot tapping (full bore valves only).

M&J Valve was founded in 1962 by Marvin

Grove and has been a leader in the pipeline

valve industry since its inception. Now part

of SPX FLOW, Inc., the M&J Valve brand

meets or exceeds the quality standards of

our customers and the valve industry. M&J

Valve product offering includes slab and

expanding through-conduit gate valves, axial

surge valves and rotary control valves, piston,

ball, and swing check valves. With the M&J

Valve brand, SPX FLOW can provide a wide

variety of fl ow control solutions for liquid

and gas markets. This combination of

products, technical know-how and fi eld

experience has allowed for a history of

product innovation which has positioned

the M&J Valve brand in a leadership position

within the valve industry.

Finding innovative ways to help the world

meet its ever growing demand for energy

is a key focus for SPX FLOW. As a multi

industry company, we provide creative

solutions that serve global energy markets

in a myriad of ways. SPX FLOW is helping

to meet that demand with a broad range

of high quality, custom-engineered systems

and components that can also help

improve effi ciency and reduce the use of

natural resources. We also supply a wide

range of components—from air preheaters

to fi lter systems. SPX FLOW off-the-shelf

and customized solutions are supporting all

phases of oil, gas and biofuel production,

from exploration, extraction and processing

to transport and storage.

Typical product applications

3

Theory of OperationThe SPX FLOW ball valve provides both a cast body 2-piece

design and a forged body 3-piece design (in class 600 and

higher pressures) bolted body trunnion mounted design for those

hydrocarbon gas and liquid applications requiring bubble-tight

shutoff, fi re-safe construction and API 6D certifi cation. Standard

features include a positively retained stem, double block and bleed

capability, anti-static

design, and a standard seat sealant vent and drain feature. The

SPX FLOW ball valve is designed to provide ease of operation,

low torque, and extended seal life and is available in both full and

reduced bore design. The through conduit full bore API 6D design

assures unrestricted fl ow and accommodates both pigging and hot

tapping. All SPX FLOW ball valves are bi-directional and may be

installed

for fl ow in either direction. They are intended for use in horizontal

or vertical pipelines with the valve stem in any confi guration.

The trunnion mounted design maintains the ball in an exact, fi xed

position supported by the trunnions. Bearings absorb the side

load created by pressure acting on the ball. The seat rings fl oat

in the seat pocket and sealing force is generated both by springs

and line pressure. The valve has double block and bleed capability

in both open and closed position. Cycle tested under the most

severe conditions to provide long service life under the toughest

conditions, in both high and low and varying pressure and fl ow

conditions.

OI L AN D GAS PROD UCTION

• Pressure Control

• Water Injection

• Cavern Storage

• Separator Isolation

• Off-Shore Platforms

GAS GATH E R I NG, GAS PLANTS, GAS TRAN S M I SS ION

• Metering & Regulating Stations

• Temperature, Pressure and Flow Control

• Launcher/Receiver

• Natural Gas Pipelines

• Emergency Shut Down

• Compressor Stations

TE R M I NALS, STORAG E AN D DOWN STR EAM CONVE R S ION

• Gas Storage Facilities

• LNG Liquefaction and Gasifi cation Facilities

• Power Plant Gas Supply

• LDC Interconnects

4

Product Specifi cations

S EAT S EALI NG FEATU R E S

This seat design provides excellent sealing capability at

both high and low differential pressures.

The springs are used to provide an additional mechanical

load to energize the seats under low pressure. Wave

springs are used in valve sizes 2" through 4" Class 150 &

300 also 2" Class 900 & 1500 while coil springs are used

in all other sizes and pressure classes. For low pressure

service the springs provide a uniform mechanical force

exerted around the entire sealing surface of the seats as

they are pressed against the ball. Coil springs are closely

spaced around the seat ring in a special groove that allows

compression of the springs. These springs are kept evenly

spaced by a specially designed stainless steel band which

also helps to protect the springs during installation and

maintenance. Even spacing of the springs provides a

uniform load of the seats on the ball.

Fluid and pressure are prevented from leaking past the

seat ring by tail O-Ring seals. This tail O-Ring also acts as

a piston seal allowing the seat ring to become pressure

energized.

E M E RG E NCY S EAT S EAL

Under standard operating conditions the M&J ball valve

does not require any lubrication or routine maintenance.

However, in the event the seat seal is damaged during

operation, an emergency sealant injection system is

standard on all valves. Sealant can be injected directly to

the seat sealing area to affect a temporary emergency

seal. If valves are to be buried, or are located in an

inaccessible location, the grease sealant fi ttings can be

extended per customer requirements.

Figure 1

Sealant Inject ion

Body

Seat Holder

Spring

Seat Holder O-Ring

Seat

Bal l

Figure 2

Sealant Inject ion

Body

Seat Holder O-Ring

Seat Holder

Spring

Seat

Bal l

Figure 3

Sealant Inject ion Fitt ing

Seat Holder

Body

Seat

Bal lCap

5

ANTI-B LOWOUT STE M D E S IG N AN D STE M S EAL

A positively retained anti-blowout stem is standard on all SPX FLOW

ball valves. This feature allows the top works to be removed with the

valve under pressure.

The standard stem seal design utilizes three seals to ensure stem seal

integrity. The primary seal is a backseated design using reinforced TFE.

This seal is combined with a secondary inner seal and an externally

replaceable outer seal. A port with a check fi tting is provided between

the inner and outer seals. This port allows seal integrity testing and

venting prior to outer seal removal and replacement.

TR U N N ION D E S IG N

The M&J ball valve is a trunnion mounted design. The trunnions are fi tted into TFE lined bearing blocks supported within the valve body.

The trunnions are an integral part of the ball and precisely locate and support the ball while ensuring low, consistent torque.

DOU B LE B LOCK AN D B LE E D FEATU R E

The M&J ball valve is designed to allow for double block and bleed. The body cavity can be vented with the ball in either the full-open

or full-closed position. This is possible with pressure on either or both the upstream or downstream sides of the valve. The valve body

is furnished with a vent fi tting located in the upper half of the body center section. There is a pipe plug in the bottom of the body for

draining.

FI R E TE ST QUALI FICATION S

The SPX FLOW ball valve has been designed to comply with international standards. This includes fi re testing per ISO 10497.

Fire test qualifi ed design and certifi cation can be provided when specifi ed.

VALVE BODY PR E SSU R E R E LI E F

When the SPX FLOW ball valve is in service, the fl ow media can be isolated and contained within the body cavity when the valve is closed.

During this time, the fl ow media can expand and contract due to temperature variations. Thus, as the temperature rises, the fl uid expands,

increasing the pressure in the body cavity. In order to avoid over-pressuring the body cavity, the M&J ball valve seats are designed to self

relieve the over-pressure, allowing the fl ow media to vent through the seat into the pipeline. This self-relieving feature is standard on all

M&J ball valves.

VALVE E N D CON N ECTION S

The SPX FLOW ball valve can be supplied with a variety of end connections including RTJ and Raised Face fl anged end, weld end, or

fl anged by weld end. Standard face to face dimensions are per API-6D. End fl anges are supplied to meet B16.5, B16.47 Type A, or MSS-

SP44 depending on valve size.

SPX FLOW ball valves standard weld end on carbon steel body valves made from either A216 WCB or ASTM A105 having a specifi ed

minimum yield strength (SMYS) of 36,000 psi. This material can be fi eld welded and matches the material of most common fl anges.

The standard weld preparation is bored to match the specifi ed mating pipe. The bevel thickness is 1.5 times the mating pipe thickness

allowing direct welding to mating pipe having a SMYS of 52,000 psi or less. Welding to higher strength pipe may require transition pieces

(pups) or a change in specifi cation of the valve end material.

Consult SPX FLOW for special end connections on M&J Valve products including fl anges and weld ends to match your requirements.

6

S PAR E PARTS

While the SPX FLOW ball valve is designed to

provide trouble free service, we recommend that

spare parts be inventoried in operations having

numerous valves of a given size for customers

having an in-house maintenance program.

Having spare parts on site will help to reduce

downtime and maintain valves so that they

provide years of service.

For those customers without in-house service

capabilities, spare parts and factory service

personnel can be obtained directly from the

factory. Please provide the valve serial number

when contacting SPX FLOW. The serial number

can be found on the nameplate and is also

stamped on the valve body, Identifying the serial

number will expedite any request and ensure

that correct information is provided.

WarrantySPX FLOW warrants all original M&J Valve equipment to be free from defects in workmanship and material, provided that such equipment

was properly selected for the service intended, properly installed, and not misused. M&J Valve equipment which is returned transportation

prepaid within 12 months from date of

installation or 18 months from date of

shipment, whichever expires fi rst and if

found by SPX FLOW's inspection to be

defective in workmanship or material will be

repaired or replaced,

at SPX FLOW’s option, free of charge

and return-shipped lowest cost

transportation prepaid.

NOTE: With exception to the warranty set forth above, SPX FLOW makes no express or implied warranties, no warranty of merchantability, no warranty of fi tness of purpose, and no other warranties which extend beyond the description on the face hereof.

NAM E PLATE

Nameplates on SPX FLOW and M&J ball valves provide all of the information necessary to identify the valve when contacting the factory

for assistance or spare parts.

Service InformationR ECOM M E N D E D S PAR E PARTS

PARTN U M B E R OF S I M I LAR VALVE S TO B E SU PPORTE D

<10 11-20 21-30 31-40

Ball 0 1 2 3

Seat Assembly 0 2 4 6

Stem 0 1 2 3

O-Rings 1 set 2 sets 4 sets 6 sets

Coil 0 2 sets 4 sets 6 sets

Gear Box 0 0 1 1

Vent Fit t ing 1 1 2 2

Thrust Washer 2 4 4 6

Bearing 2 2 4 4

7

59

14

32

30

08

07

09

11

2

05

06

2736343338 351

09

03

06

04

34

05

13

10

52

53

33

24

22

44

54

42

21

Cut-Away View

2-PI ECE BALL VALVE TR U N N ION-MOU NTE D

ITE M NO. PART MATE R IAL

1 Body A216-WCB

2 Cap A216-WCB

3 Bal l A351-CF8

4 Stem A276-304

5 Body O-Ring H N B R

6 Seat RTFM

7 Stem O-Ring H N B R

8 Stem Bush DU-B EAR I NG

9 Back Seat RTFE

10 Pack ing G RAPH ITE

11 Body/Cap Bol t A193-B7M

12 Body/Cap Nut A194-2H M

13 Gland A276-304

14 Gland Bol t A4135+H1150

20 Ant is t a t ic Dev ice 316L SS

21 Gear Box C.S

22 Gear Box Bol t A193-B7M

24 Key A1045


27 Body Gasket G RAPH ITE

30 Gland Bush RTFE

32 Housing A276-304

33 Trunn ion A276-304

34 Trunn ion Gasket 304SS+G RAPH ITE

35 Trunn ion Bush DU-B EAR I NG (CS+PTFE)

36 Trunn ion O-Ring H N B R

38 Trunn ion Bol t A193-B7M

40 Seat Holder A351-CF8

41 Seat Holder O-Ring H N B R

42 Seat Holder O-Ring H N B R

44 Spr ing I NCON E L X-750

52 Vent A1020+Zn.

53 Dra in A1020+Zn.

54 Seal In ject ion A1020+Zn.

55 Suppor t Leg C.S

59 Housing O-Ring H N B R

8

Cut-Away View3-PI ECE BALL VALVE TR U N N ION-MOU NTE D


1 Body A105N

2 Cap A105N

3 Bal l A351-C F8

4 Stem A276-304 A182-304

5 Body O -Ring H N B R

6 Seat D EVLO N

7 Stem O -Ring H N B R

8 Stem Bush D U B EAR I N G (CS+PTF E)

9 Back Seat RTF E

10 Pack ing G R AP H ITE

11 Body/Cap Bol t A193-B7M

12 Body/Cap Nut A194-2H M

13 Gland A1045

14 Gland Bo l t A4135+H1150

20 Ant i -Sta t ic 316L S S

21 Gear Box CS

22 Gear Box Bo l t A193-B7M

23 Gear Box Nut A194-2H M

24 Key A1045

27 Body Gasket G R AP H ITE


28 Gland O -Ring H N B R

29 Gland Gasket G R AP H ITE

30 Gland Bush D U B EAR I N G (CS+PTF E)

31 Gland P in A1045

40 Seat Holder A351-C F8

41 Seat Holder O -Ring H N B R

43 Seat Holder Gasket G R AP H ITE

44 Spr ing X-750

45 Bear ing P la te A1045

56 Bear ing P la te Bush D U B EAR I N G (CS+PTF E)

47 Bear ing P la te L iner RTF E

48 Bear ing P la te P in A1045

49 Mount ing P la te A1045

50 Mount ing P la te Bo l tA4135+H1150

51 Mount ing P la te P in A1045

52 Vent A1020+Zn.

53 Dra in A1020+Zn.

54 Sealant In ject ion A1020+Zn.

55 Spor t ing Leg CS

56 Li f t ing Lug CS

9

PARTCAST STAI N LE SS

SOU R (NACE)CAST SOU R LOW

TE M P (NACE)FORG E D STAI N LE SS

SOU R (NACE)FORG E D SOU R LOW

TE M P (NACE)

Body A351-C F8M (316S S) A352-LC C A182-F316 A350-LF2

Cap A351-C F8M (316S S) A352-LC C A182-F316 A350-LF2

Bal l A351-C F8M (316S S) A351-C F8 (304S S)* A351-C F8M (316S S) A351-C F8 (304S S)*

Stem A276-316 / A182-316 A276-304 / A182-304* A276-316 / A182-316 A276-304 / A182-304*

Stud Bo l t/ Nut A193-B8 / A193-B8 A193-B7M / A194-2H M A193-B8 / A193-B8 A320-L7M / A194-7M

Body-Cap O -Ring H N B R H N B R H N B R H N B R

Body-Cap Gasket Graph i te Graph i te Graph i te Graph i te

Seat Ho lder A351-C F8M (316S S) A351-C F8 (304S S)* A351-C F8M (316S S) A351-C F8 (304S S)*

Seat D EVLO N D EVLO N D EVLO N D EVLO N

Seat Holder O -Ring- 1 H N B R H N B R H N B R H N B R

Seat Ho lder O -Ring-2 H N B R H N B R H N B R H N B R

Seat Ho lder Gasket Graph i te Graph i te Graph i te Graph i te

Spr ing I N C O N E L X-750 I N C O N E L X-750 I N C O N E L X-750 I N C O N E L X-750

Bear ing P la te Bush D U+PTF E D U+PTF E D U+PTF E D U+PTF E

Ant i -Sta t ic Ba l l & Spr ing ASTM A276-316L ASTM A276-316L ASTM A276-316L ASTM A276-316L

Stem Bush D U+PTF E D U+PTF E D U+PTF E D U+PTF E

Thrust Washer RTF E RTF E RTF E RTF E

Stem O -Ring H N B R H N B R H N B R H N B R

Pack ing Graph i te Graph i te Graph i te Graph i te

Mount ing P la te A351-C F8M (316S S) A352-LC C A351-C F8M / A182-F316 A350-LF2

Thrust Bear ing RTF E RTF E RTF E RTF E

Vent P lug 316S S A1020+Zn 316S S A1020+Zn

Sealant In ject ion 316S S A1020+Zn (316S S Ba l l Check) 316S S A1020+Zn

(316S S Ba l l Check)

* A351-CF8M (316SS) is ava i lab le

Optional Materialss

10

Trunnion Dimensional Data

CLASS 150

SIZE Ød L-RF L-RTJ L-BW H WEIGHT

In mm In mm In mm In mm In mm In mm Lbs . kg

2 50 2 50 7 178 7.5 190.5 8.5 216 4.4 113 39.6 18

3×2 80×50 2 51 8 203 8.5 216 11 283 4 113 57.2 26

3 80 3 76 8 203 8.5 216 11 283 8 195 88 40

4×3 100×80 3 76 9 229 9.5 241 12 305 8 195 132 60

4 100 4 100 9 229 9.5 241 12 305 8 208 176 80

6×4 150×100 4 102 16 394 16.0 406 18 457 8 208 275 125

6 150 6 150 16 394 16.0 406 18 457 11 283 352 160

8x6 200x150 6 152 18 457 18.5 470 20.5 521 9.8 250 462 210

8 200 8 200 18 457 18.5 470 20.5 521 11.0 280 556.6 253

10x8 250x200 8 203 21 533 21.5 546 22 559 11 280 726 330

10 250 10 250 21 533 21.5 546 22 559 13 340 851.4 387

12x10 300x250 10 254 24 610 24.5 622 25 635 13 340 1045 475

12 300 12 300 24 610 24.5 622 25 635 15 370 1232 560

14x12 350x300 12 303 27 686 27.5 699 30 762 15 370 1408 640

14 350 14 337 27 686 27.5 699 30 762 15 390 1672 760

16x14 400x350 14 337 30 762 30.5 775 33 838 15 390 2002 910

16 400 16 387 30 762 30.5 775 33 838 17 430 2200 1000

18x16 450x400 16 387 34 864 34.5 876 36 914 17 430 2420 1100

18 450 18 438 34 864 34.5 876 36 914 19 490 2673 1215

20x16 500x400 16 387 36 914 36.5 927 39 991 17 430 3256 1480

20 500 20 489 36 914 36.5 927 39 991 22 550 3850 1750

24x20 600x500 20 489 42 1067 42.5 1080 45 1143 22 550 5500 2500

24 600 24 589 42 1067 42.5 1080 45 1143 25 640 6798 3090

11

S IZE Ød L-RF L-RTJ L-BW H WEIGHT


2 50 2 50 8.5 216 9.1 232 8.5 216 4.3 110 46.2 21

3×2 80x50 2 51 11.1 283 9.1 232 11.1 283 4.3 110 68.2 31

3 80 3 76 11.1 283 11.7 298 11.1 283 6.5 165 105.6 48

4×3 100x80 3 76 12.0 305 11.7 298 12.0 305 6.5 165 154 70

4 100 4 100 12.0 305 12.6 321 12.0 305 8.3 210 198 90

6x4 150x100 4 102 15.9 403 12.6 321 18.0 457 8.3 210 297 135

6 150 6 150 15.9 403 16.5 419 18.0 457 9.8 250 396 180

8x6 200x150 6 152 19.8 502 20.4 518 20.5 521 9.8 250 528 240

8 200 8 200 19.8 502 20.4 518 20.5 521 11.0 280 594 270

10x8 250x200 8 203 22.4 568 23.0 584 22.0 559 11.0 280 946 430

10 250 10 250 22.4 568 23.0 584 22.0 559 13.4 340 1100 500

12x10 300x250 10 254 25.5 648 26.1 664 25.0 635 13.4 340 1342 610

12 300 12 300 25.5 648 26.1 664 25.0 635 14.6 370 1474 670

14x12 350x300 12 303 30.0 762 30.6 778 30.0 762 14.6 370 1760 800

14 350 14 337 30.0 762 30.6 778 30.0 762 15.4 390 2035 925

16x14 400x350 14 337 33.0 838 33.6 854 33.0 838 15.4 390 2420 1100

16 400 16 387 33.0 838 33.6 854 33.0 838 16.9 430 2750 1250

18x16 450x400 16 387 36.0 914 36.6 930 36.0 914 16.9 430 3080 1400

18 450 18 438 36.0 914 36.6 930 36.0 914 19.3 490 3498 1590

20x16 500x450 16 387 39.0 991 39.8 1010 39.0 991 16.9 430 3630 1650

20 500 20 489 39.0 991 39.8 1010 39.0 991 21.7 550 4840 2200

24x20 600x500 20 489 45.0 1143 45.9 1165 45.0 1143 21.7 550 6160 2800

24 600 24 589 45.0 1143 45.9 1165 45.0 1143 25.2 640 7480 3400


CLASS 300

12



2 50 2 50 11.5 292 11.6 295 11.5 292 4.3 110 68 31

3×2 80x50 2 51 14.0 356 14.1 359 14.0 356 4.3 110 86 39

3 80 3 76 14.0 356 14.1 359 14.0 356 6.5 165 132 60

4×3 100x80 3 76 17.0 432 17.1 435 17.0 432 6.5 165 165 75

4 100 4 100 17.0 432 17.1 435 17.0 432 8.3 210 242 110

6x4 150x100 4 102 22.0 559 22.1 562 22.0 559 8.3 210 330 150

6 150 6 150 22.0 559 22.1 562 22.0 559 9.8 250 550 250

8x6 200x150 6 152 26.0 660 26.1 664 26.0 660 9.8 250 638 290

8 200 8 200 26.0 660 26.1 664 26.0 660 11.3 288 1056 480

10x8 250x200 8 203 31.0 787 31.1 791 31.0 787 11.3 288 1210 550

10 250 10 250 31.0 787 31.1 791 31.0 787 13.5 343 1650 750

12x10 300x250 10 254 33.0 838 33.1 841 33.0 838 13.5 343 1760 800

12 300 12 300 33.0 838 33.1 841 33.0 838 14.9 378 2200 1000

14x12 350x300 12 303 35.0 889 35.1 892 35.0 889 14.9 378 2420 1100

14 350 14 337 35.0 889 35.1 892 35.0 889 15.5 394 2376 1080

16x14 400x350 14 337 39.0 991 39.1 994 39.0 991 15.5 394 2376 1080

16 400 16 387 39.0 991 39.1 994 39.0 991 17.3 440 3300 1500

18x16 450x400 16 387 43.0 1092 43.1 1095 43.0 1092 17.3 440 3630 1650

18 450 18 438 43.0 1092 43.1 1095 43.0 1092 19.7 500 4510 2050

20x16 500x450 16 387 47.0 1194 47.2 1200 47.0 1194 17.3 440 4576 2080

20 500 20 489 47.0 1194 47.2 1200 47.0 1194 21.7 551 5720 2600

24x20 600x500 20 489 55.0 1397 55.4 1406 55.0 1397 21.7 551 7040 3200

24 600 24 589 55.0 1397 55.4 1406 55.0 1397 25.2 640 10340 4700


CLASS 600

13



2 50 2 49 14.5 368 14.6 371 14.5 368 4.3 110 105.6 48

3×2 80x50 2 49 15.0 381 15.1 384 15.0 381 4.3 110 114.4 52

3 80 3 74 15.0 381 15.1 384 15.0 381 6.5 165 176 80

4×3 100x80 3 74 18.0 457 18.1 460 18.0 457 6.5 165 209 95

4 100 4 100 18.0 457 18.1 460 18.0 457 8.3 210 308 140

6x4 150x100 4 100 24.0 610 24.1 613 24.0 610 8.3 210 451 205

6 150 6 150 24.0 610 24.1 613 24.0 610 9.8 250 792 360

8x6 200x150 6 150 29.0 737 29.1 740 29.0 737 9.8 250 968 440

8 200 8 201 29.0 737 29.1 740 29.0 737 11.3 288 1276 580

10x8 250x200 8 201 33.0 838 33.1 841 33.0 838 11.3 288 1518 690

10 250 10 252 33.0 838 33.1 841 33.0 838 13.5 343 2200 1000

12x10 300x250 10 252 38.0 965 38.1 968 38.0 965 13.5 343 2530 1150

12 300 12 303 38.0 965 38.1 968 38.0 965 14.9 378 3300 1500


CLASS 900

14



2 50 2 49 14.5 368 14.6 371 14.5 368 4.3 110 110 50

3×2 80x50 2 49 18.5 470 18.6 473 18.5 470 4.3 110 154 70

3 80 3 74 18.5 470 18.6 473 18.5 470 6.6 167 213.4 97

4×3 100x80 3 74 21.5 546 21.6 549 21.5 546 6.6 167 264 120

4 100 4 100 21.5 546 21.6 549 21.5 546 7.0 179 440 200

6x4 150x100 4 100 27.8 705 28.0 711 27.8 705 7.0 179 627 285

6 150 6 144 27.8 705 28.0 711 27.8 705 10.2 260 1056 480

8x6 200x150 6 144 32.8 832 33.1 841 32.8 832 10.2 260 1232 560

8 200 8 192 32.8 832 33.1 841 32.8 832 12.0 304 1804 820

10x8 250x200 8 192 39.0 991 39.4 1000 39.0 991 12.0 304 2244 1020

10 250 9 239 39.0 991 39.4 1000 39.0 991 14.3 363 3300 1500

12x10 300x250 9 239 44.5 1130 45.1 1146 44.5 1130 14.3 363 3850 1750

12 300 11 287 44.5 1130 45.1 1146 44.5 1130 16.4 417 4840 2200


CLASS 1500

15

Size

Ød W T1 T2 L1 L2 L3N1 * H1

N2 * H2

ØG ØC1 C2 ØD

In mm In mm In mm In mm In mm In mm In mm In mm In mm In mm In mm

2x2 0.79 20 0.55 14 0.08 2 0.35 9 0.55 14 0.75 19 0.69 17.54 * M8

2 * M12

1.50 38 2.76 70 2.44 62 3.54 90

3x2 0.79 20 0.55 14 0.08 2 0.35 9 0.55 14 0.75 19 0.69 17.54 * M8

2 * M12

1.50 38 2.76 70 2.44 62 3.54 90

3x3 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

4x3 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

4x4 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

6x4 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

CLASS 600

Size

Ød W T1 T2 L1 L2 L3N1 * H1

N2 * H2

ØG ØC1 C2 ØD


2x2 0.79 20 0.55 14 0.08 2 0.35 9 0.55 14 0.75 19 0.69 17.54 *

M102 *

M101.50 38 4.02 102 3.90 99 4.92 125

3x2 0.79 20 0.55 14 0.08 2 0.35 9 0.55 14 0.75 19 0.69 17.54 *

M102 *

M101.50 38 4.02 102 3.90 99 4.92 125

3x3 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

4x3 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

4x4 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

6x4 1.18 30 0.79 20 0.08 2 0.71 18 - 1.18 30 1.00 25.54 *

M102 * M8

1.57 40 4.02 102 3.15 80 4.92 125

CLASS 900

Size

Ød W T1 T2 L1 L2 L3N1 * H1

N2 * H2

ØG ØC1 C2 ØD


2x2 1.18 30 0.79 20 0.08 2 0.35 9 0.00 0 0.77 19.5 0.47 124 *

M102 *

M101.69 43 4.02 102 3.90 99 4.92 125

3x2 0.79 20 0.55 14 0.08 2 0.35 9 0.00 0 0.77 19.5 0.47 124 *

M102 *

M101.69 43 4.02 102 3.90 99 4.92 125

3x3 1.18 30 0.79 20 0.08 2 0.71 18 0.00 0 0.77 19.5 0.47 124 *

M102 *

M101.69 43 4.02 102 3.90 99 4.92 125

4x3 1.18 30 0.79 20 0.08 2 0.71 18 0.00 0 0.77 19.5 0.47 124 *

M102 *

M101.69 43 4.02 102 3.90 99 4.92 125

CLASS 150/300

Actuator Mounting Dimensions

16

Topworks Data

CLASS 150

Size ØS H T1 T2 Key N D ØGISO MTG

ØC ØD

In In mm In mm In mm In mm In mm In mm In mm In mm Flange In mm In mm

6x6 1.38 35 2.56 65 0.12 3 0.98 25 0.39x0.31 10 × 8 0.16 4 0.59 15 3.39 86 F12 4.92 125 6.89 175

8x6 1.38 35 2.56 65 0.12 3 0.98 25 0.39x0.31 10 × 8 0.16 4 0.59 15 3.39 86 F12 4.92 125 6.89 175

8x8 1.57 40 2.56 65 0.16 4 0.98 25 0.47x0.31 12 × 8 0.16 4 0.75 19 3.98 101 F14 5.51 140 6.89 175

10x8 1.57 40 2.56 65 0.16 4 0.98 25 0.47x0.31 12 × 8 0.16 4 0.75 19 3.98 101 F14 5.51 140 6.89 175

10x10 2.17 55 3.11 79 0.20 5 0.87 22 0.63x0.39 16 × 10 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

12x10 2.17 55 3.11 79 0.20 5 0.87 22 0.63x0.39 16 × 10 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

12x12 2.17 55 3.11 79 0.20 5 0.87 22 0.63x0.39 16 × 10 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

14x12 2.17 55 3.11 79 0.20 5 0.87 22 0.63x0.39 16 × 10 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

14x14 2.56 65 4.33 110 0.20 5 0.98 25 0.71x0.43 18 × 11 0.31 8 0.75 19 6.34 161 F20 8.07 205 10.04 255

16x12 2.17 55 3.11 79 0.20 5 0.87 22 0.63x0.39 16 × 10 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

16x14 2.56 65 4.33 110 0.20 5 0.98 25 0.71x0.43 18 × 11 0.31 8 0.75 19 6.34 161 F20 8.07 205 10.04 255

16x16 2.76 70 4.53 115 0.20 5 1.06 27 0.79x0.47 20 × 12 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

18x18 3.15 80 4.53 115 0.20 5 1.06 27 0.87x0.55 22 × 14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x16 2.76 70 4.53 115 0.20 5 1.06 27 0.79x0.47 20 × 12 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x18 3.15 80 4.53 115 0.20 5 1.06 27 0.87x0.55 22 × 14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x20 3.35 85 4.92 125 0.20 5 1.18 30 0.98x0.55 25 × 14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

24x20 3.35 85 4.92 125 0.20 5 1.18 30 0.98x0.55 25 × 14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

24x24 3.94 100 5.12 130 0.20 5 1.38 35 1.10x0.63 28 × 16 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

26x26 4.33 110 5.91 150 0.20 5 1.57 40 1.26x071 32 × 18 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

30x24 3.94 100 5.12 130 0.20 5 1.38 35 1.10x0.63 28 × 16 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

17

Topworks Data

CLASS 300


ØC ØD


6x6 1.57 40 2.95 75 0.16 4 0.98 25 0.47x0.31 12x8 0.16 4 0.75 19 3.98 101 F14 5.51 140 6.89 175

8x6 1.57 40 2.95 75 0.16 4 0.98 25 0.47x0.31 12x8 0.16 4 0.75 19 3.98 101 F14 5.51 140 6.89 175

8x8 1.57 40 2.95 75 0.20 5 0.98 25 0.47x0.31 12x8 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

10x8 1.57 40 2.95 75 0.20 5 0.98 25 0.47x0.31 12x8 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

10x10 2.17 55 3.11 79 0.20 5 0.91 23 0.63x0.39 16x10 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

12x10 2.17 55 3.11 79 0.20 5 0.91 23 0.63x0.39 16x10 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

12x12 2.17 55 3.11 79 0.20 5 0.91 23 0.63x0.39 16x10 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

14x12 2.17 55 3.11 79 0.20 5 0.91 23 0.63x0.39 16x10 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

14x14 2.56 65 4.33 110 0.20 5 0.98 25 0.71x0.43 18x11 0.31 8 0.75 19 6.34 161 F20 8.07 205 10.04 255

16x12 2.17 55 3.11 79 0.20 5 0.91 23 0.63x0.39 16x10 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

16x14 2.56 65 4.33 110 0.20 5 0.98 25 0.71x0.43 18x11 0.31 8 0.75 19 6.34 161 F20 8.07 205 10.04 255

16x16 2.76 70 4.53 115 0.20 5 1.06 27 0.79x0.43 20x11 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

18x18 3.15 80 4.53 115 0.20 5 1.06 27 0.87x0.55 22x14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x16 2.76 70 4.53 115 0.20 5 1.06 27 0.79x0.47 20x12 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x18 3.15 80 4.53 115 0.20 5 1.06 27 0.87x0.55 22x14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x20 3.35 85 4.92 125 0.20 5 1.18 30 0.98x0.55 25x14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

24x20 3.35 85 4.92 125 0.20 5 1.18 30 0.98x0.55 25x14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

24x24 3.94 100 5.12 130 0.20 5 1.38 35 1.10x0.63 28x16 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

26x26 4.33 110 5.91 150 0.20 5 1.57 40 1.26x071 32x18 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

30x24 3.94 100 5.12 130 0.20 5 1.38 35 1.10x0.63 28x16 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

18

Topworks Data


ØC ØD


6x6 1.77 45 3.15 80 0.16 4 1.18 30 .47x.35 14x9 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

8x6 1.77 45 3.15 80 0.16 4 1.18 30 .47x.35 14x9 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

8x8 2.36 60 3.15 80 0.20 5 1.18 30 .71x.43 18x11 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

10x8 2.36 60 3.15 80 0.20 5 1.18 30 .71x.43 18x11 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

10x10 2.95 75 3.74 95 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

12x10 2.95 75 3.74 95 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

12x12 2.95 75 4.13 105 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

14x12 2.95 75 4.13 105 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

14x14 2.95 75 4.33 110 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

16x12 2.95 75 4.13 105 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

16x14 2.95 75 4.33 110 0.20 5 1.18 30 .79x.47 20x12 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

16x16 3.35 85 3.94 100 0.20 5 1.18 30 .98x.55 25x14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

18x18 3.54 90 4.72 120 0.20 5 1.18 30 .98x.55 25x14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

20x16 3.35 85 3.94 100 0.20 5 1.18 30 .98x.55 25x14 0.31 8 0.75 19 7.91 201 F25 10.00 254 11.81 300

20x18 3.54 90 4.72 120 0.20 5 1.18 30 .98x.55 25x14 0.31 8 0.87 22 9.09 231 F30 11.73 298 13.78 350

20x20 3.94 100 6.69 170 0.20 5 1.18 30 1.10x .63 28x16 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

24x20 3.94 100 6.69 170 0.20 5 1.18 30 1.10x .63 28x16 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

24x24 4.33 110 6.69 170 0.20 5 1.38 35 1.26x.71 32x18 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

26x26 4.72 120 7.09 180 0.20 5 1.57 40 1.26x.71 32x18 0.31 8 1.54 39 11.85 301 F40 15.98 406 18.70 475

30x30 5.12 130 7.87 200 0.20 5 1.77 45 1.42x.79 36x20 0.47 12 1.54 39 14.61 371 F48 19.02 483 22.05 560

30x24 4.33 110 6.69 170 0.20 5 1.38 35 1.26x.71 32x18 0.31 8 1.30 33 10.28 261 F35 14.02 356 16.34 415

CLASS 600-900


ØC ØD


2 1.10 28 1.77 45 0.12 3 0.79 20 0.31x0.28 8x7 0.16 4 0.55 14 3.39 86 F12 4.92 125 5.91 150

3 1.10 28 1.77 45 0.12 3 0.79 20 0.31x0.28 8x7 0.16 4 0.55 14 3.39 86 F12 4.92 125 5.91 150

4 1.38 35 2.17 55 0.12 3 0.79 20 0.39x0.31 10x8 0.16 4 0.55 14 3.39 86 F12 4.92 125 5.91 150

6 1.77 45 3.15 80 0.16 4 1.18 30 0.55x0.35 14x9 0.16 4 0.87 22 5.16 131 F16 6.50 165 8.27 210

8 2.36 60 3.15 80 0.20 5 1.18 30 0.71x0.43 18x11 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

10 2.95 75 3.74 95 0.20 5 1.18 30 0.79x0.47 20x12 0.31 8 0.75 19 6.34 161 F20 8.07 205 9.84 250

CLASS 1500

19

Torque Chart

PRESSURE (PS IG)

S IZE CLASS 150

MAST

CLASS 300

MAST

CLASS 600

MAST

CLASS 900

MAST

CLASS 1500

MAST

i n mm (0ps i ) (285ps i ) (740ps i ) (1480ps i ) (2220ps i ) (3705ps i )

2 50 260 347 1736 738 1736 1302 1736 1823 3906 2777 3906

3 75 443 955 5989 1823 5989 2777 5989 3454 7985 4496 7985

4 100 868 1389 5989 2430 5989 5538 7291 7195 9461 10068 14148

6 150 2604 4600 14148 7291 14148 13019 20224 14755 20224 22133 27688

8 200 5208 6944 14148 12151 14148 16925 47825 26039 47825 39058 93479

10 250 6076 11197 36888 14755 36888 19529 93479 27775 93479 41662 113443

12 300 10416 13540 36888 21439 36888 28643 93479 50255 136096

14 350 15623 21699 47825 29164 47825 48606 93479 85581 221591

16 400 23435 29511 76033 42964 76033 56418 136096 100597 221591

18 450 32983 42096 113443 58153 113443 97646 221591 179147 486753

20 500 33851 44440 136096 80113 136096 102420 221591 177585 486753

24 600 38624 77249 189910 99816 189910 138874 294847 213258 675448

26 650 47738 118477 294847 190952 294847 320538 907454 461322 1292048

28 700 65097 133927 486753 213519 486753 342498 907454 508626 1292048

30 750 78117 149289 486753 231746 486753 403602 1292048

32 800 91136 169426 675448 254573 675448 422177 1292048

34 850 107627 174460 675448 279397 675448 453944 1292048

36 900 114571 196420 675448 294413 675448 487968 1292048

40 1000 134534 239297 907454 329131 907454 585267 1772378

42 1050 140176 253966 907454 368710 907454 603234 1772378

The above torque va lues do not conta in ser v ice fac tors . Soak ing e f fects and/or par t ic le mat ter in the va lve may cause an increase in the torque. For in termedia te pressure use the torque express ions for the s ta ted pressure range. The re-seat to rque is taken as 0 .75 t imes the break torque. (18 over 0 .8 t imes) For power opera t ion , mul t ip ly a l l o f the above va lues by a fac tor o f 1 .25 or customer speci f ied fac tor whichever is la rger. For opera t ing temperatures between -20°F to -50°F ( -29°C to -46°C) mul t ip ly these va lues by 1 .20. Actuator se lect ion should be made on customer exper ience and appropr ia te ser v ice fac tors .

ASME CLASSES 150–1500 MOP TORQUE

Ball Valve Torque Chart - Trunnion mounted ball valve.Torque and MAST in in-lb.Pressure in pounds per square inch.

20

Ball Valve Model Number Key

BN – F38 – 60 IA – D A R – 8 G D

FOR EXAMPLE

BN-F38-60IA-DAR-8GD

8" API 6D Monogrammed NACE MR0175 Compliant, 3-Pc End Entry Trunnion Ball Valve,

Full Port, Class 600, A105N CS Body, 304 Trim, Devlon Seat, HNBR Seals, RFF, Gear, Domestic

Valve Type

B Ball N Standard

Classifi cation

R2 Reduced Split Body 7 Floating ball- Graphite + O-Ring packing (Fire Safe)

R3 Reduced Split Body(3P)*

8 Trunnion mounted- O-Ring + Graphite packing (Fire Safe)

F2 Full Split Body

F3 Full Split Body(3P)

Rating

15 ASME 150

30 ASME 300

60 ASME 600

90 ASME 900*

150 ASME 1500*

250 ASME 2500*

Body & Trim Material

A A351-CF8

B A351-CF8M

F A216-WCB

H A352-LCC

I A105N*

J A350-LF2*

N A182-F316*

O A182-F316L*

P A182-F51*

Seat Material

P PTFE (TFM-1600)

R RPTFE (GLASS 15%)

D DEVLON™*

K PEEK

T Metal+TungCarbide*

X RTFM Glass+Graphite

Seals

A Graphite+HNBR

B Graphite+Viton GLT

End Connection

B Butt Weld

F Flat Face

R Raised Face

J Ring Joint

X Special

Size

1 1(25)

2 2(50)

3 3(80)

4 4(100)

5 5(125)

6 6(150)

8 8(200)

10 10(250)

12 12(300)*

14 14(350)*

16 16(400)*

18 18(450)*

20 20(500)*

22 22(550)*

24 24(600)*

26 26(650)*

28 28(700)*

30 30(750)*

32 32(800)*

34 34(850)*

36 36(900)*

40 40(1000)*

46 46(1150)*

Operator

Blank Import

D Domestic*

* Denotes on ly ava i lab le in Trunnion Bal l Va lves .

Operator

L Lever

G Worm Gear

B Bare Stem

X Special

21

° ° ° °

° ° ° °

° ° ° ° ° ° ° ° ° F° ° ° ° ° ° ° ° ° ° C°

Pressure / Temperature Rating

22

Other M&J Valve Branded ProductsEXPANDING GATE VALVES

The M&J Model EG valves are full-bore

through-conduit valves with rising stem,

parallel expanding gate and segment for

tight mechanical seal and positive shut-off,

both upstream and downstream, under both

low and high differential pressure. This valve

provides a superior bidirectional mechanical

seal because the two-piece gate assembly

expands against the seating areas in

open or closed position. The greater the

torque, the tighter the seal. The result is

an extremely heat-resistant seal, unaffected

by line pressure or vibration.

Key Features

• Increased throughput full-bore

unrestricted fl ow

• Tight seal in all fl ow conditions;

bi-directional mechanical sealing

• Can replace two valves; double block

and bleed capability

• Long, leak-free service life; protected

seat design

• Easy to operate and maintain

• Sizes 2" and larger in all ANSI classes

COMPACT EXPANDING

GATE VALVE

The M&J Model CEG valves are full- or

reduced-opening, non-through-conduit

valves with rising stem, parallel expanding

gate and segment for tight mechanical

seal and positive shut-off, both upstream

and downstream, under both low and high

differential pressure. This design has proven

performance in applications worldwide,

such as isolation valves in power plants,

ESD valves in production, block valves

in process systems, high-temperature

valves in refi neries, and pipeline valves

in critical areas.

Key Features

• Superior sealability through use of

two-piece parallel expanding gate

• Double block and bleed

• Traps pressure in body cavity

when in closed position

• Pressure gauge seating; long seat life

• Stem seal’s chevron rings ensure

sealing integrity

• In-line maintenance

• Sizes 4" and larger, Classes 150 and 300

DANFLO SURGE

RELIEF VALVES

DANFLO surge relief valves are engineered

to track unabated surge (wave pressure

transients), open quickly and then close

without slamming shut. The “speed of

response” in surge valves is defi ned as

the valve’s ability to relieve peak wave

surge fl ow in the time stated in a hydraulic

transient surge analysis. Although this

time varies with each application, timed

responses of 100 milliseconds or less are

not unusual. DANFLO surge relief valves

meet these criteria.

Key Features

• High fl ow capacities (Cv) achieve required

surge protection with smaller and/or

fewer valves, saving both installation

cost and weight

• Fast response — rapid opening/closing

without slamming shut — enables

tracking of the surge

• Additional reserve fl ow capacity

accommodates unforeseen transient

surge fl ow

• Set pressure test port to meet DOT

periodic-testing requirements

M-303M&J VALVE S LAB GATE VALVE

PE R FOR MANC

TH R U-CON D U

CE LEAD E R I N

IT GATE VALVE S

Expanding Gate Valve

Compact Expanding Gate Valvvee

Swing Check Valve

23

Houston, TX

Large Valve CNC

Robotic Welder

ISO/API Certifi cates

SPX FLOW and Quality PolicySPX FLOW is committed to providing to providing products and services that meet

or exceed API and customer requirements, and strive to constantly improve customer

satisfaction through employee participation.

Trunnion Mounted Ball Valve

S PX FLOW, I NC.

8800 Westplain Dr.

Houston, TX 77041

P: (800) 231-3690 or (281)469-0550

F: (281) 894-1332

E: mjvalve@spxfl ow.com

SPX FLOW, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation.

Design features, materials of construction, and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confi rmed

in writing. Please contact your local sales representative for product availability in your region. For more information, visit www.spxfl ow.com.

The green “ ” and “ ” are trademarks of SPX FLOW, Inc.

MJ-1964-US Version 01/2016 Issued 01/2016

COPYRIGHT © 2016 SPX FLOW, Inc.

Based in Charlotte, North Carolina, SPX FLOW, Inc. (NYSE:FLOW) is a leading global supplier of highly engineered fl ow components, process equipment and turn-key systems, along with the related aftermarket parts, serving the food and beverage, power and energy and industrial end markets. For more information, please visit www.spxfl ow.com.

trunnion mounted ball valve - spx · pdf file2 spx flow trunnion mounted ball valve spx flow,...

Documents