suzuki sdt operator’s manualtraining.suzukiauto.co.za/sasatrainingdocs/ge01 suzuki...

EN05 Engine Auxiliary Systems I Student Guide 1 Charging systems

Suzuki Introduction Course code: GE01

Suzuki SDT operator’s

manual

Preface

Read this document carefully so that you can use this tester correctly and safely. This manual only describes the functions of the SDT diagnosis software.

Preface

- i -

For safe usage

This document uses symbols for warnings, cautions, and prohibitions. These symbols and their meanings are as follows. Pleasemake sure you fully understand the meanings of these symbols before reading the rest of this document.

For safe usage

WARNING This indicates an item for which incorrect handling can result in a major accident involving death or serious injury.

CAUTIONIndicates an item for which incorrect handling can lead to injury or damage to property. Under certain conditions, more serious consequences may result.

PROHIBITIED Indicates a prohibited method of handling.

WARNINGDo not work connect the tester cables etc. while the vehicle is running.Doing so could result in an accident.

- ii -

Table of contents

1 InstallationInstallation of the SDT diagnosis software .................................................................................................... 2

Required Environment .................................................................................................................................... 2Installing the software for your PC.................................................................................................................. 3Installing the SDT diagnosis software to the SUZUKI SDT ............................................................................ 6SUZUKI SDT Update Procedure .................................................................................................................... 8About the Found New Hardware Wizard ...................................................................................................... 11

2 Basic OperationsStarting and Ending........................................................................................................................................ 14

Starting.......................................................................................................................................................... 14Ending........................................................................................................................................................... 16

Screen Configuration ..................................................................................................................................... 17Main Menu Buttons ....................................................................................................................................... 17Title Bar......................................................................................................................................................... 18Menu Bar ...................................................................................................................................................... 19

Basic Operations ............................................................................................................................................ 22Display Operation ......................................................................................................................................... 22Main Unit Operation ...................................................................................................................................... 24

In Case of Error ............................................................................................................................................... 25Communication Errors .................................................................................................................................. 25System Errors ............................................................................................................................................... 26Screen Lock Errors ....................................................................................................................................... 26

3 Diagnostics FunctionsMode Selection................................................................................................................................................ 28System Selection ............................................................................................................................................ 29Bus Check ....................................................................................................................................................... 31

Communication Bus Check........................................................................................................................... 31Communication Malfunction DTC ................................................................................................................. 32

DTC Check....................................................................................................................................................... 33DTC Data Display ......................................................................................................................................... 33DTC Data Storage ........................................................................................................................................ 34DTC Data Clear ............................................................................................................................................ 36Freeze Frame Data Display .......................................................................................................................... 37

Data List........................................................................................................................................................... 38Data List Display ........................................................................................................................................... 38Display Switching.......................................................................................................................................... 40Snapshots ..................................................................................................................................................... 47How to use the optional accessory Trigger Snapshot................................................................................... 50Data List Manager......................................................................................................................................... 54

Active Test....................................................................................................................................................... 56Active Test Item Selection ............................................................................................................................ 56Active Test Execution ................................................................................................................................... 57

Utilities ............................................................................................................................................................. 59Keyless start system (For vehicle not equipped with Immobilizer control system) ....................................... 60VIN Registration (For models on and after 05MY in North American market) .............................................. 62Readiness Test ............................................................................................................................................. 67Retrieving All DTCs....................................................................................................................................... 68Hydraulic control test .................................................................................................................................... 72

Table of contents

- iii -

Table of contents

Sensor Calibration ........................................................................................................................................ 76ESP® Function Setting ................................................................................................................................. 77TPS ID registration........................................................................................................................................ 79Clear Air Bag Information.............................................................................................................................. 80Dead Lock Control Test ................................................................................................................................ 82Clear Lock..................................................................................................................................................... 84Clear Lamp ................................................................................................................................................... 85

Utilities (GST Mode)........................................................................................................................................ 86Readiness Test ............................................................................................................................................. 87VIN (Vehicle Identifications Number) Display ............................................................................................... 87Cal.ID (Calibration Identifications) Display.................................................................................................... 88CVN (Calibration Verification Numbers) Display........................................................................................... 88

4 Diagnostics Functions (for screen type 2)DTC Check....................................................................................................................................................... 90

DTC (Current/History DTC) Display.............................................................................................................. 90DTC Clear ..................................................................................................................................................... 91Freeze Frame Data Display .......................................................................................................................... 92DTC (Pending DTC) Display......................................................................................................................... 93

Data List........................................................................................................................................................... 94Data List Display ........................................................................................................................................... 94Pre-Lock Function......................................................................................................................................... 95Data List Selection ........................................................................................................................................ 96Graph Display ............................................................................................................................................... 98Snapshots ................................................................................................................................................... 100Snapshot Playback ..................................................................................................................................... 106

5 Saved Data Playback FunctionsDTC Playback ................................................................................................................................................ 111Snapshot Playback ....................................................................................................................................... 113

Playback With Snapshot Flag Set............................................................................................................... 115

6 Measurement FunctionsVoltage Measurement Functions................................................................................................................. 118

Measurement Function Selection Menu ..................................................................................................... 118Voltage Display ........................................................................................................................................... 119Waveform Display....................................................................................................................................... 120Calibration................................................................................................................................................... 122Screen Image Save/Playback/Delete ......................................................................................................... 123

Oscilloscope Functions ............................................................................................................................... 127Oscilloscope Measurement Menu............................................................................................................... 127Waveform Display....................................................................................................................................... 128Trigger Menu............................................................................................................................................... 130Screen Image Save/Playback/Delete ......................................................................................................... 134

7 AppendixAbout the use of the installation information clear program (cleaner).................................................... 142

Introduction ................................................................................................................................................. 142Precaution................................................................................................................................................... 142Before use................................................................................................................................................... 142Operating procedure for the cleaners ......................................................................................................... 143

- iv -

1 Installation

1 Installation

1 Installation

Following your purchase of the SUZUKI SDT, the first time you turn the power switch on the SUZUKI SDT to ON, the following Installation screen is displayed.

In order to run the fault diagnosis, you will need to install the SDT diagnosis software to SUZUKI SDT.

Get the installers from the website or the CD provided by your Distributor, and run installation for the software (USB driver, SDT-Viewer, SDT diagnosis software program).

The following environment is required for installation. SUZUKI SDT main unitPC Recommended SpecificationsCPU: Intel Pentium/Celeron or PC with a compatible processor.

(366MHz or higher is recommended)Memory: 128MB or more.OS: Microsoft Windows 98SE, ME, 2000, XP, VistaInterface: USB1.1 or 2.0AC/DC adapterUSB cable or RS-232C cable (optional accessory)

Installation of the SDT diagnosis software

Required Environment

Installation screen

- 2 -

1 Installation

Install the SUZUKI SDT dedicated software onto your PC.

Get the installers from the website or the CD provided by your Distributor, and run installation for the software (USB driver, SDT-Viewer, SDT diagnosis software program).

SUZUKI SDT dedicated USB driverSDT-ViewerSDT diagnosis software program

Close all other applications before running the installers.

1. Install the "SUZUKI SDT dedicated USB driver".This is a USB driver software for SUZUKI SDT. When you execute this one, USB driver is installed on your PC.

Please install this USB driver software on your PC ONCE before you install SDT-Viewer.

Steps:

1) Double click the program "WinRTUSBDriver.exe" and start the installer.

Installing the software for your PC

NOTEPlease install this one before you connect a USB cable between SUZUKI SDT and PC.You have to be ADMINISTRATOR when you install this one on Windows 2000 and Windows XP, Windows Vista.

NOTEIf you execute the installer on a PC on which the USB driver software is already installed, the following message to confirm uninstallation is displayed.[Do you want to completely remove the selected application and all of its components?] In this event, quit the installer.

- 3 -

1 Installation

2) The installer starts and installation of the USB driver software starts. Follow the instructions on your screen.

NOTEIf the "Installation completed screen" is not displayed, re-install the "USB driver".If the "Installation completed screen" is not displayed, even after the re-installation has been performed, use the cleaner for the USB driver. Reference: Page 142

- 4 -

1 Installation

2. Install the "SDT-Viewer".This is a installer of SDT-Viewer and related software. When you execute this one, SDT-Viewer and related software are installed on your PC.

Steps:

1) Double click the program "Setup SDT Viewer.exe" and start the installer.

2) The installer starts and installation of the SDT-Viewer starts. Follow the instructions on your screen.

3) When installation on your PC is complete, a shortcut for SDT-Viewer is created on your PC's desktop.

3. Install the "SDT diagnosis software program".This installer has software data of SDT diagnosis software program. After you install this one, Software Update Wizard can install SDT diagnosis software to SUZUKI SDT.

Steps:

1) Double click the program "SDT_ImageInstaller.exe" and start the installer.

2) The installer starts and installation of SUZUKI SDT's Software Update Wizard (SUW) starts. Follow the instructions on your screen.

NOTEIf you execute the installer on a PC on which the same version of SDT-Viewer is already installed, the following message to confirm uninstallation is displayed.[Do you want to completely remove the selected application and all of its components?] In this event, quit the installer.

NOTEIf the "Installation completed screen" is not displayed, re-install the "SDT-Viewer".If the "Installation completed screen" is not displayed, even after the re-installation has been performed, use the cleaner for the SDT-Viewer. Reference: Page 142

NOTEIf you execute the installer on a PC on which the same version of SUW is already installed, the following message to confirm uninstallation is displayed.[Do you want to completely remove the selected application and all of its components?] In this event, quit the installer.

NOTEIf the "Installation completed screen" is not displayed, re-install the "SDT diagnosis software program".If the "Installation completed screen" is not displayed, even after the re-installation has been performed, use the cleaner for the SDT diagnosis software program. Reference: Page 142

- 5 -

1 Installation

The following environment is required for installation.PCwith the following software installed

USB driverSDT-ViewerSDT diagnosis software program

SUZUKI SDT main unitAC/DC adapterUSB cable or RS-232C cable (optional accessory)

1. Connect the AC/DC adapter to your SUZUKI SDT.

2. Connect your PC and the SUZUKI SDT with a USB cable or RS-232C cable.

Installing the SDT diagnosis software to the SUZUKI SDT

Power switch

AC/DC adapter

USB cable

PC USB port

Note: USB ports may be located in a

different area depending on

your PC.

- 6 -

1 Installation

3. Turn the power switch on the SUZUKI SDT to ON, and bring up the Installation screen or the Onboard/offboard check screen.

4. Double click the "SDT-Viewer" icon that has been created on your desktop, and start up SDT-Viewer.

5. Click the "Software Update Wizard" button on the first screen of the SDT-Viewer, and start up the version upgrade program.Reference: Page 8 SUZUKI SDT Update Procedure (Chapter 1 Installation/Installation of the SDT diagnosis

software)

NOTEWhen the USB cable is connected to the PC forthe first time after the installation of the driver,the Found New Hardware Wizard may bedisplayed.For details on how to use the wizard, refer to"About the Found New Hardware Wizard ".Reference: Page 11 About the Found New

Hardware Wizard

NOTEInstallation should take about 10 minutes.Upgrading the SDT diagnosis software does not cause any data stored in the SUZUKI SDT to be deleted.

Installation screen Onboard/offboard check screen

Found New Hardware Wizard screen

- 7 -

1 Installation

1. Before starting to update the SUZUKI SDT, perform the setup steps. Make sure you perform steps 1) - 3) in the center of the window correctly and then click .

2. Communication setup between the SUZUKI SDT and the PC takes place. Wait until the window changes.

3. When communication setup is confirmed, the current SUZUKI SDT version and the update version are displayed. To carry out the update, click .

SUZUKI SDT Update Procedure

NOTEIf the SDT diagnosis software is not installed onto the SUZUKI SDT, the Installation screen is displayed.

PC screen ( TOP screen )

Next >

Installation screen

PC screen ( Communication screen )

PC screen ( Version check screen )

Next >

- 8 -

1 Installation

4. The SUZUKI SDT update begins. The window displays the estimated time until update completion.

5. When the update is complete, click to end the update process.

NOTEIf the current SUZUKI SDT version and the update version are the same, the window on the right appears. To forcibly overwrite, click

.

CAUTIONDo not switch off the SUZUKI SDT power during the upgrade. Switching off the power may lead to an incomplete software upgrade.

NOTEIf an error occurs between the SUZUKI SDT and the PC, an error window is displayed. Check the cable connection between the SUZUKI SDT and the PC.If the above checks have been performed, and there are no problems, turn the power button of the SUZUKI SDT off. And run the update procedure from step 1 after turning the SUZUKI SDT on again.If the error screen is displayed, even when the update procedure has been performed again, use the cleaner for the USB driver. Reference: 2

PC screen ( Warning screen )

Next >

PC screen ( Updating screen )

PC screen ( Complete screen )

Finish

PC screen ( Communication error )

- 9 -

1 Installation

6. The upgraded SUZUKI SDT diagnostic software starts up.

7. When the SDT diagnosis software starts up, the Onboard/offboard check screen is displayed. Select [Version Information] from the [system] menu. The version information screen is displayed.

8. Check the SDT diagnosis software version.If the SDT diagnosis software starts up properly and the version information is correct, the upgrade is complete.

CAUTIONIf the upgrade is interrupted or not completed properly, the version upgrade error screen shown on the right appears on the SUZUKI SDT. If this happens, carry out the upgrade again by running the Software Update Wizard function of the SDT-Viewer software on your PC while the version upgrade error screen is still showing.

Opening screen Onboard/offboard check screen

Version information screen[System] menu

Version upgrade error screen

- 10 -

1 Installation

If the Found New Hardware Wizard is displayed when the USB cable is connected to the PC, follow the procedure below.

1. After selecting "No, not this time" on the Found New Hardware Wizard, click the

.The Installation method selection screen is displayed.

2. After selecting "Install the software automatically" on the Installation method selection screen, click the .The installation of the software starts. When the installation is complete, the Installation completed screen is displayed.

3. Click the on the Installation completed screen.The Installation completed screen closes.

About the Found New Hardware Wizard

NOTEConfirm that the message "Denso Corporation Port" is displayed under the "This wizard helps you install software for:".

Found New Hardware Wizard screen

Next >

Installation method selection screen

Next >

Installation completed screen

Finish

- 11 -

1 Installation

4. Check the status of the communication between the SUZUKI SDT and the PC.

4-1. Start up the Software Update Wizard of the SDT-Viewer.4-2. Perform Steps 1 to 3 of the "SUZUKI SDT Update Procedure". (Reference: Page 8)

If the PC screen (Version check screen) is displayed, without any communication errors occurring, the communication status is normal.

- 12 -

2 Basic Operations

2 Basic Operations

2 Basic Operations

1. Connect the SUZUKI SDT and vehicle side datalink connectors (DLC) with the datalink cable.

2. Turn the vehicle ignition switch ON.

3. Press the SUZUKI SDT power switch to turn the power ON.

Starting and Ending

Starting

NOTECommunication with the vehicle computer (ECU) is not possible if the ignition switch is at OFF or ACC. When the SUZUKI SDT is turned ON, always switch the ignition switch ON or start the engine.When the SUZUKI SDT is used as measurement function (voltage measurement, oscilloscope), it will work even if the ignition switch is at OFF or ACC.If the SUZUKI SDT is connected to the vehicle’s diagnostic connector (DLC) by a datalink cable and supplied with power via an AC/DC adapter or DC power cable for a cigarette lighter socket, the SUZUKI SDT can be operated even with its power switch turned off.

CAUTIONDuring startup, never switch the SUZUKI SDT power switch OFF until the onboard/offboard check screen is displayed.

- 14 -

2 Basic Operations

After start-up, the Installation screen or the Opening screen is displayed, followed by the Onboard/offboard check screen.

NOTEIf the SDT diagnosis software is not installed onto the SUZUKI SDT, the Installation screen is displayed.If the SDT diagnosis software has been properly installed from the website or the CD provided by your Distributor, the Onboard/offboard check screen is displayed. For details on how to install the SDT diagnosis software, refer to Chapter 1 Installation in this manual.Reference: Page 2 Installation of the SDT diagnosis software

Installation screen

Opening screen Onboard/offboard check screen

- 15 -

2 Basic Operations

1. Turn the vehicle ignition switch OFF.

2. Press the SUZUKI SDT power switch to turn the power OFF.

3. Disconnect the datalink cable from the vehicle side datalink connector (DLC).

Ending

CAUTIONIf the power to the SUZUKI SDT is switched OFF during an Active Test, the actuator may remain in the drive state. Always end the Active Test before switching the power OFF.

CAUTIONWhen disconnecting the datalink cable from vehicle side datalink connector (DLC), gently pull it straight out of the connector.Pulling the cable at a slant can break the connector pins.When pulling the cable out, hold it by the connector section, and never by the cord section. Pulling on the cord section can break the lines in the cable.

- 16 -

2 Basic Operations

The screen configuration for the SUZUKI SDT is as follows.

The main menu buttons are composed of frequently used functions.These functions can be selected from the menu bars, but the main menu buttons enable these functions to be started at one touch.

ACTIVE KEY

Screen Configuration

NOTEThe SUZUKI SDT display is a touch panel, so use your fingers to operate it.When a menu bar or button item is displayed in gray, this indicates that the item is disabled.

Main Menu Buttons

Starts the DTC check. For ECM, PCM or TCM of some markets, freeze frame data can also be checked with a DTC check.

Starts the data list. Snapshots can also be recorded with the data list.

Switches the data list display format.

Starts an Active Test.

Starts the utility.

Screen Configuration (Screen Type 1)

Menu Bar

Title Bar

Information display area

Function buttons

Main Menu Buttons

Main Menu Buttons

DTC

Data List

View

Active Test

Utility

- 17 -

2 Basic Operations

The title bar displays the ECU name and function names. Icons displaying the power status and communications status are also shown at the right end.

The icon display at the right end of the title bar varies according to the connection between the SUZUKI SDT and the vehicle computer (ECU).

Battery iconThis icon is displayed when the SUZUKI SDT and the vehicle computer (ECU) are not connected, to show that the SUZUKI SDT is running on its internal battery. The battery icon also functions as an indicator showing the charge level (remaining power) for the internal battery.

Connector iconThis icon is displayed when the SUZUKI SDT and the vehicle computer (ECU) are correctly connected, to show that the SUZUKI SDT is running on vehicle power. The connector icon also functions as an indicator by showing the communications status with its color.When communication starts, the connector icon changes color according to the communication speed: low speed (green), medium speed (yellow) and high speed (red). The communication speed is determined by the vehicle computer (ECU).

Title Bar

NOTEThe connector icon is displayed even when the SUZUKI SDT is being charged via an AC/DC adaptor. The icon turns white during charging.

Battery icon Connector icon

- 18 -

2 Basic Operations

Five menu titles are displayed in the menu bar.Touching a menu titles displays the list of its functions.

[Function] menuThe [Function] menu is used to select the program for execution.The functions that can be selected from the [Function] menu are as follows.

Menu Bar

NOTEDepending on the vehicle to be diagnosed, the following menu screen may be displayedIn such cases, neither the [Function] menu nor the [View] menu can be displayed.Most of the time, the screen configuration of screen type 2 is displayed when diesel engine systems are diagnosed.

For details on the operational procedure for each function, please refer to "Chapter 4 Diagnostics Functions (for screen type 2)".Reference: Page 90 Chapter 4 Diagnostics Functions (for screen type 2)

Function Contents Referencepage

System Select Moves to the system select screen. P.29

DTC

Starts the DTC check.For ECM, PCM or TCM of some markets, freeze frame data can also be checked with a DTC check.

P.33

Data ListStarts the data list.Snapshots can also be recorded with the data list.

P.38

Active Test Starts an Active Test. P.56

Utility Starts the utility. P.59

GST (Generic Scan Tool) Mode Starts diagnosis in the GST mode. P.86

Snapshot Record Starts snapshot recording. P.47

Snapshot Configuration Starts snapshot detail setting. P.51

Snapshot Review Displays a saved snapshot data file. P.113

Saved Data Review Displays a saved DTC data file. P.114

Data List Manager Starts the data list manager. P.54

Screen Configuration (Screen Type 2)

[Function] menu

- 19 -

2 Basic Operations

[View] menuThe data list display form can be selected from the [View] menu. However, the [View] menu is only enabled when the [Data List] or [Active Test] function is selected from the [Function] menu. Functions that can be selected from the [View] menu are as follows.

Function Contents Referencepage

Data List Displays the monitor items, values, and units in a list on one line. P.42

MeterDisplays the monitor items, values (enlarged), maximum, and minimum values, and units in a list on one line.

P.43

Line Graph 1

Displays the monitor items, values (broken-line graph), maximum, and minimum values, and units in a list on one line.

P.44

Line Graph 2Displays the monitor items, values, and units in a list on one line together with a broken-line graph of the values.

P.45

Bar GraphDisplays the monitor items, values (bar graph), maximum, and minimum values, and units in a list on one line.

P.46

Graph Setting

Sets the vertical axis for graphing the displayed data. (Meter, Line Graph1, LineGraph2, Bar Graph only)Sets the buzzer to ON/OFF for when the maximum value or minimum value displayed on a graph other than for Data List or Line Graph2 is updated.

-

[View] menu

- 20 -

2 Basic Operations

[System] menuTool option functions (default setting functions) can be selected from the [System] menu.The functions that can be selected from the [System] menu are as follows.

BarThe function button displays are switched ON/OFF by touching the [Bar].

HelpWhen [Help] is touched with [Data List] or [Active Test] selected, an explanation of the item is displayed.When [Help] is touched with [Utility] selected, an explanation of the functions is displayed.

Functions Contents

Set Up Sets the backlight and displaybrightness, and the buzzer.

Unit Conversion Sets the speed, temperature,pressure, and flow units.

Language Select Selects the language used with theSUZUKI SDT.

Date/Time Sets the date and time.

Version Information Displays version information forthe SUZUKI SDT.

Memory Selectt Sets the data storage destination(memory or card).

Screen Configuration Corrects the touch panel touch keys.

Button Configuration Sets the shortcut keys, and switches the screen image save function ON/OFF.

[System] menu

- 21 -

2 Basic Operations

Touch panel operationThe display for the SUZUKI SDT is a touch panel. Operations on the display are all operated using your fingers.

To select an item from a list or press a button, briefly tap the item or button with your finger.

Replacing the screen overlay for the displayWhen removing the screen overlay, grasp the screen overlay with your fingers and remove.Use a soft cloth to wipe the surface of the touch panel clean of any dust etc.When inserting the screen overlay, insert it into the gap between the top section and the bottom section of the display.

Basic Operations

Display Operation

CAUTIONTo protect the display from scratches, always insert the screen overlay.Always operate the touch panel with your fingers. Never use any other object.

Example of a screen displaying

buttons

Example of screen displaying items

in a list

- 22 -

2 Basic Operations

Scroll bar operationA scroll bar is displayed on a screen displaying a list. The scroll bar can be used to scroll upand down the list.

If you move your finger up/down while touching the scroll bar, the list scrolls up/down.Touching / once scrolls the list up/down one line.Touching and holding / scrolls the list up/down continuously.

Software keyboard operationWhen it is necessary to input characters on the screen, use the software keyboard.

Methods for use are as follows.The keyboard can input English alphanumerics.To delete a character, use the (backspace) key.To switch between uppercase and lowercase English letters, use the key.To input accented characters (such as à and Ä) not displayed on the keyboard, touch the key. The keyboard display switches to accented characters.

Example of screen with scroll bar

displayed

Backspace key

Enter key

Cursor keysSpace bar

Shiftáü

- 23 -

2 Basic Operations

The main unit of the SUZUKI SDT has four hardware keys.All operations of the SUZUKI SDT can be carried out on the display, but four hardware keys are used for frequently-used functions in order to improve operability.

The hardware key functions are as follows.

Main Unit Operation

Hardware key Functions

Scroll up key

This key is enabled when a list (and a scroll bar) is shown on the display. It scrolls the list up.Pressing this key once scrolls the list up one line; holding the key down scrolls the list up continuously.

Scroll down key

This key is enabled when a list (and a scroll bar) is shown on the display. It scrolls the list down.Pressing this key once scrolls the list down one line; holding this key down scrolls the list down continuously.

Left function key Used to return from the screen currently being displayed to the onboard/offboard check screen.

Right function key

Normally used to return to the system select screen.Used to start/stop measurement during voltage measurement and measurement with the oscilloscope function.When screen image saving is set to "ON", pressing this key saves the screen image.

- 24 -

2 Basic Operations

If a communication error occurs while the SUZUKI SDT is in use, the following error message is displayed.

If a communications error occurs, check the error according to the following procedure.

1. Touch [OK] at the top right of the error message window.This closes the window and returns to the head screen of the function in which the communication error occurred.

2. Turn the vehicle ignition switch OFF.

3. Turn the SUZUKI SDT power switch OFF. A connection defect for the datalink cable may be the cause of a communication error. Check the datalink connector (DLC) connection at the SUZUKI SDT and vehicle sides.

4. Restart the SUZUKI SDT.Check if the communication error occurs again.

If so, connect the SUZUKI SDT to another vehicle (of the same model) and check if a communication error occurs with that vehicle.

If no communication error occursThere may be a problem with the vehicle. Inspect and repair the vehicle as necessary, in accordance with the vehicle repair manual.If a communication error occursThere may be a problem with the SUZUKI SDT.

In Case of Error

Communication Errors

- 25 -

2 Basic Operations

If a system error occurs while the SUZUKI SDT is in use, an error message dialog box like the following is displayed.

If a system error occurs, follow the procedure listed below.

1. Touch in the error message dialog box.

2. Turn the SUZUKI SDT power switch OFF.

3. Turn the SUZUKI SDT power switch ON to restart the SUZUKI SDT.If restarting the SUZUKI SDT does not eliminate the system error, write down the error message and ask the service reception staff.

If there is no response when the touch keys are pressed or the screen locks up when using the SUZUKI SDT, follow the procedure listed below.

1. Turn the SUZUKI SDT power switch OFF.

2. Press the reset switch beside the CF card slot.

3. Turn the SUZUKI SDT power switch ON to restart the SUZUKI SDT.If the screen lock is still not released after restarting, enter the necessary information on the Repair Order Sheet included with the main unit and contact your distributor for repairs.

System Errors

Screen Lock Errors

OK

- 26 -

3 Diagnostics Functions


3 Diagnostics FunctionsThe onboard/offboard check screen is displayed after the opening screen is displayed when the SUZUKI SDT starts up. When is touched on the onboard/offboard check screen, the SUZUKI SDT begins communication with the vehicle and check the ECU in the SUZUKI mode. Select “GST (Generic Scan Tool) Mode” from the function menu on the onboard/offboard check screen when starting diagnosis in the GST mode. To execute measurement functions such as the oscilloscope that do not require communication with the vehicle, touch .

Select the diagnosis mode before starting your diagnosis.The diagnosis mode features the SUZUKI mode which makes it possible to diagnose all system using the enhanced diagnosis functions for SUZUKI vehicle, and the GST mode which makes it possible to perform powertrain related diagnosis only using limited functions that make use of telecommunication methods that comply with OBDII legal regulations like North American/ European markets.

<SUZUKI mode>Touch on the onboard/offboard check screen. System select screen is displayed.

<GST mode> Select "GST Mode" from the function menu on the onboard/offboard check screen. System select screen is displayed.

NOTEVehicle's manual selection function is currently not supported.

Mode Selection

NOTEWhen performing failure diagnosis for SUZUKI vehicles, always use SUZUKI mode. In the event that it is not possible to use the SUZUKI mode, please make use of the GST mode.Please be advised that there may be instances wherein it is not possible to use the GST mode due to the vehicle’s specifications.

Onboard/offboard check screen

Auto

Utility

Manual

Auto

- 28 -


It is necessary to select the diagnostics system (the system within the vehicle) when diagnosing the vehicle.The procedure for selecting the system is as follows.

Automatic Vehicle Selection

1. Touch the list box on the system select screen to select the vehicle computer (ECU) type.A list of the vehicle mounted systems being diagnosed is then displayed.

2. Touch the system to undertake diagnosis from the system list.

ACTIVE KEY

System Selection

NOTEAfter the SUZUKI SDT is started, the system select screen is displayed. To reselect a system after having moved to other processing, press the right function key on the main unit or select the menu bar [Function] menu list >> [System Select]. This displays the system select screen.

Starts the CAN bus check.

System select screen

(SUZUKI mode)


(GST Mode)

[Function] Menu list

Bus Check

- 29 -


NOTEAfter the system has been selected, the vehicle selection screen may be displayed.

Select the vehicle to be diagnosed from the vehicle selection screen, and then touch .

Depending on the vehicle to be diagnosed, the following menu screen may be displayed.Most of the time, this screen is displayed when diesel engine systems are diagnosed.

For details on the operational procedure for each function, please refer to "Chapter 4 Diagnostics Functions (for screen type 2)". Reference: Page 90 Chapter 4 Diagnostics Functions (for screen type 2)

NEXT

Vehicle selection screen

Menu screen (Screen Type 2)

- 30 -


You can efficiently diagnose a CAN Bus malfunction (disconnection, short circuit, etc.) using two functions, "Communication Bus Check" and "Communication Malfunction DTC".

A Bus Check cannot be performed on a vehicle in which the CAN bus is not connected to the diagnostic connector (DLC).

The ECU connected to the CAN Bus is checked and the ECU name is displayed.

The procedure for checking the ECU connected to the CAN Bus is as follows.

1. Touch on the system select screen.The function select screen is displayed.

2. Select "Communication Bus Check" on the function select screen and touch .The CAN Bus connection check screen is displayed.

Bus Check

NOTEYou can not use the Bus Check in the GST mode.

Communication Bus Check

NOTEThe ECU name is not displayed if communication is disabled due to a CAN Bus circuit disconnection, ECU defect, etc.

NOTEThe connection with the CAN Bus is regularly checked and the screen is updated at intervals of about two seconds.When the display is updated, the background color changes with an increase or decrease in vehicle computers (ECUs) connected. An increase in ECUs makes the background blue and a decrease makes it grey.

Bus Check

Enter

CAN Bus connection check

screen

*ESP® is a registered trademark of Daimler Chrysler AG.

Function select screenSystem select screen

- 31 -


Only DTCs showing communication malfunctions (DTC U****) from all ECUs connected to the CAN Bus are detected and displayed.

The procedure for checking the communication malfunction DTC is as follows.

1. Touch on the system select screen.The function select screen is displayed.

2. Select "Communication Malfunction DTC" on the function select screen and touch .The communication malfunction DTC check screen is displayed.

3. Select the name of the ECU whose details you want to display and touch .The DTC details check screen is displayed.

Communication Malfunction DTC

NOTEDTCs other than communication malfunction are not displayed.

Bus Check

Enter

Function select screen Communication malfunction DTC

check screenSystem select screen

Details

DTC details check screen

- 32 -


DTC data is data stored in the vehicle computer (ECU) internal memory when a trouble occurs. Checking DTC data can aid in specifying the cause of the trouble.

Displays the DTC data for the system selected on the system select screen.The procedure for displaying the DTC data is as follows.

1. Select the system from the system select screen.

2. Touch the main menu button.Alternatively, touch [DTC] in the system select screen [Function] menu list.The DTC data list is displayed on the DTC data display screen.

ACTIVE KEY

DTC Check

DTC Data Display

NOTEA "number" displayed at the left of DTC data shown in orange means that freeze frame data has been recorded for that data.Reference: Page 37 Freeze Frame Data Display (Chapter 3 Diagnostics Functions/DTC Check)

Displays the current DTC data.When there is DTC data, this button is displayed in blue.

Displays pending DTC data.When there is pending DTC data, this button is displayed in blue.

Displays historical DTC data (past codes).When there is historical DTC data, this button is displayed in blue.

Saves DTC data. Reference: Page 34

Clears the DTC data stored in the vehicle computer (ECU). Reference: Page 36

DTC

[Function] Menu list DTC data display screenSystem select screen

Current

Pending

History

Clear

- 33 -


DTC data can be stored. The factory setting for the data storage destination is the internal memory. The data storage destination can be changed using the data storage setting function.The procedure for saving the DTC data is as follows.

1. From the DTC data display screen function buttons, touch .The DTC data save screen is displayed.

2. The set file name is displayed on the DTC data save screen.

If this file name is correct, touch .To save to a different file, input the name of that file, and then touch .Reference: Page 23 Scroll bar operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)The first time this screen is displayed, "System name _ECU ID_Date_ Serial number" is set automatically as the file name displayed.

ACTIVE KEY

DTC Data Storage

NOTEThe ECU ID is a special ID for use when the SDT diagnosis software communicates with the ECU. This ID is not necessary to run the vehicle diagnosis.

Saves DTC data.

Cancels DTC data saving.

NOTEThe stored DTC data can be played back at any time. The SUZUKI SDT does not need to be connected to the vehicle for playback.Reference: Page 111 DTC Playback (Chapter 5 Saved Data Playback Functions)

SaveSave

DTC data display screen DTC data save screen

Save

Cancel

- 34 -


If the storage memory is full, the DTC data delete verification dialog box is displayed and unnecessary DTC data can be deleted.

ACTIVE KEY

Displays a list of stored data.

Cancels DTC data deletion.

DTC data delete verification dialog box

Delete Files

Cancel

- 35 -


The procedure for clearing the DTC data is as follows.

1. From the DTC data display screen function buttons, touch .The DTC data clear dialog box is displayed.

2. On the DTC data clear dialog box, touch .Delete DTC data by following the operating instructions on the screen.

DTC Data Clear

Clear

Yes

DTC data display screen

DTC data clear dialog box

- 36 -


Displays freeze frame data related to the DTC data.ECU data recorded when the DTC data is generated

The procedure for displaying freeze frame data is as follows.

1. On the DTC data display screen, touch the DTC data displayed in orange with "a number" to the left.

ACTIVE KEY

Freeze Frame Data Display

NOTEYou can check whether there is any freeze frame data with the display on the left of the DTC data.The display may show a number, "H" or "L".Number: There is freeze frame data.H: Indicates a failure that occurs when the ECU detects a voltage at or above a specified value. There is

no freeze frame data.L: Indicates a failure that occurs when the ECU detects a voltage at or below a specified value. There is no

freeze frame data.No display: There is no freeze frame data.

Returns the display to the DTC data display screen.

DTC data display screen Freeze frame data

display screen

Exit

- 37 -


Vehicle computer (ECU) data can also be monitored numerically or in graph form and snapshots can be recorded.

Displays the ECU data for the system selected on the system select screen.The procedure for displaying the ECU data is as follows.

1. Select the system with the system select screen.

2. Touch the main menu button.Alternatively, touch [Data List] in the system select screen [Function] menu list.ECU data is displayed on the data list screen.

Data List

Data List Display

Data List

[Function] menu listSystem select screen Data list screen

- 38 -


Measurement group selectionData required for diagnosing a specific breakdown can be grouped.The ECU data belonging to a measurement group can be displayed by selecting that group.

1. From the data list screen list box, select the measurement group.When you select a measurement group, the ECU data belonging to that group is displayed.

ACTIVE KEY

Starts the data list manager and adds the displayed data. Reference: Page 54

Ends display of the selected data.This is not valid unless data has been selected.

Moves the selected data to the head of the list and holds it there.This is not valid unless data has been selected.

Returns the data held at the head of the list to its original position.When the held data is selected, changes to .

Records a snapshot. Reference: Page 47

Measurement group select screenData list screen

- 39 -


Display formThere are five data list display formats.These display formats are shown below.

Display Switching

Meter Line Graph 1Data list

Line Graph 2 Bar Graph

- 40 -


Display of maximum, minimum and current values If the display forms are Meter, Line Graph 1 and Bar Graph, the maximum, minimum and current values are displayed to the left of the data.They are not displayed if the value is not a number e.g. ON/OFF.

Display format switchingThe following two methods can be used to switch the display format.

Select the display format by touching the main menu .Each time is touched, the display form switches to the next type in the following order: Data List >> Meter >> Line Graph 1 >> Line Graph 2 >> Bar Graph.

Select from the menu bar [View] menu.

Meter

ViewView

Main Menu Buttons

[View] menu

- 41 -


Data ListData List (number display) displays the data numerically.

A measurement group can be selected with the list box.You can switch the function button display on and off by touching [Bar] on the menu bar.

ACTIVE KEY

NOTEOnly 7 characters, including decimal points, can be displayed in the [Value] column of the list. If it is possible that more than 7 characters are being displayed, switch the display form to [Meter] and confirm the value.

Starts the data list manager and adds the displayed data. Reference: Page 54

Stops display of the selected data.This is not valid unless data has been selected.

Moves the selected data to the head of the list and holds it there.This is not valid unless data has been selected.

Returns the data held at the head of the list to its original position.When the held data is selected, changes to .

Records a snapshot. Reference:

Data list With the list box pulled down

- 42 -


MeterMeter (enlarged number display) displays the data as enlarged numbers.

The maximum and minimum values are displayed.The data for display can be selected using the list box. The function button display can be switched on and off by touching [Bar] on the menu bar.

ACTIVE KEY

Sets the vertical axis (value) or numeric axis range. Also turns on or off the buzzer that sounds when the "Max" or "Min" value is updated.

Sets whether to display or hide the "Max" and "Min" values.


NOTEThe range set in the is reflected when data is displayed as a Line Graph 1, Line Graph 2 and Bar Graph.

Meter When the [Bar] menu is touched With the list box

- 43 -


Line Graph 1Line Graph 1 displays the data as a line graph.

The maximum and minimum values are displayed.The current values of the data are displayed.Data can be selected using the list box. The function button display can be switched on and off by touching [Bar] on the menu bar.

ACTIVE KEY

Sets the range of the line graph's vertical axis (value). Also turns on or off the buzzer that sounds when the "Max" or "Min" value is updated.

Sets the scale of the line graph's horizontal axis (time). Also sets whether to display or hide the "Max", "Min" and "Live" values.


Line Graph 1 When the [Bar] menu is touched With the list box

- 44 -


Line Graph 2Line Graph 2 (line graph combined display) displays multiple data sets as a line graph on the same axis.

Data can be selected using the list box.The function button display can be switched on and off by touching [Bar] on the menu bar.

ACTIVE KEY

Sets the range of the line graph's vertical axis (value). Also turns on or off the buzzer that sounds when the "Max" or "Min" value is updated.

Sets the scale of the line graph's horizontal axis (time).

Sets the ground position for the selected data.


Line Graph 2 When the [Bar] menu is touched With the list box

- 45 -


Bar GraphThis function displays the data as a bar graph.

Data can be selected using the list box.The function button display can be switched on and off by touching [Bar] on the menu bar.

ACTIVE KEY

Sets the range of the bar graph's numeric axis. Also turns on or off the buzzer that sounds when the "Max" or "Min" value is updated.

Sets whether to display or hide the "Max", "Min" and "Live" values.

Records a snapshot. Reference: Page 47.

Bar Graph When the [Bar] menu is touched With the list box

- 46 -


Data in the data list can be recorded/saved/played back. In addition, settings can be performed for snapshot operation.

Snapshot recording/savingThe procedure for recording/saving snapshots is as follows.

1. Touch the function button.Alternatively, in the data list screen [Function] menu list, touch [Snapshot Record].The snapshot record/save screen is displayed.

2. Data recording/saving starts automatically.

Snapshots

[Function] menu listData list screen

When recording When saving

- 47 -


3. The set file name is displayed on the data save screen.

If this file name is correct, touch .To save to a different file, input the name of that file, and then touch .Reference: Page 23 Software keyboard operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)

The first time this screen is displayed, "System name_ECU ID_Date_Serial number" is set automatically as the file name displayed.

4. When the data saving ends, the system goes into playback / new recording standby mode.

ACTIVE KEY

NOTEThe ECU ID is a special ID for use when the SDT diagnosis software communicates with the ECU. This ID is not necessary to run the vehicle diagnosis.

Saves snapshot.

Cancels snapshot saving.

SaveSave

Playback / new recording standbyData save screen

Save

Cancel

- 48 -


You can set the snapshot flag by touching [ ] when recording.

ACTIVE KEY

NOTEThe snapshot flag stores the point as a mark for the data time elapsed. During playback, you can move quickly to points using the snapshot flags.Up to five snapshot flags can be set.Reference: Page 115 Playback With Snapshot Flag Set (Chapter 5 Saved Data Playback Functions/Snapshot

Playback)

Sets snapshot operations. Reference: Page 51

Ends the snapshot.

Stops recording/playback and returns to the start of the data.

Recording starts.

Playback starts.

Sets a snapshot flag.

Exit

- 49 -


Using the Trigger Snapshot enables you to start or stop snapshot recording or set a snapshot flag without looking at the screen.

Connecting the Trigger Snapshot

How to use Trigger Snapshot

1. Press the Trigger Snapshot button while the data list is displayed.Data recording begins.

2. Press the Trigger Snapshot button during data recording.A snapshot flag is set.

How to use the optional accessory Trigger Snapshot

CAUTIONWhen connecting the probe to the SUZUKI SDT, gently insert it straight into the connector.Inserting the probe at a slant can break the connector pins.

NOTETrigger Snapshot can be used to set snapshot flags in a maximum of five places.Reference: Page 115 Playback With Snapshot Flag Set (Chapter 5 Saved Data Playback Functions/Snapshot

Playback)Pressing the Trigger Snapshot button after five snapshot flags are set stops data recording.

- 50 -


Snapshot operation settingsSettings can be performed for snapshot operation.

1. Touch on the snapshot screen.Alternatively, in the data list screen [Function] menu list, touch [Snapshot Configuration].The snapshot operation setting screen is displayed.

The setting contents are as follows.Record TimeSets the recording time.Select from 5s/10s/15s/30s/1 min./2 min./5 min./20 min.Trigger PointSets the percentage of the recording time saved as data before the trigger is pressed.TriggerSets the type of trigger. The types of triggers are as follows.

Manual : The trigger is applied manually by touching the data list display section.Parameter : The trigger is applied at the set parameter value.DTC : The trigger is applied when a DTC is detected.Select DTC : The trigger is applied when an arbitrarily set DTC is detected.

Trigger Configuration ButtonSets the parameter triggers. This button is only active if “Parameter” is selected from the trigger items. Reference: Page 52

Snapshot operation setting screen[Function] Menu listSnapshot screen

- 51 -


Parameter trigger settingDetailed settings can be performed related to the parameter triggers.

ACTIVE KEY

Adds only the data selected in the item list to the Trigger list.

Deletes all the data in the Trigger list.

Deletes only the data selected in the Trigger list.

Moves the data selected in the Trigger list up one space.

Moves the data selected in the Trigger list down one space.

Displays the Parameter trigger level setting screen.

Trigger data selection screen

OK

- 52 -


Parameter trigger level settingDetailed settings can be performed related to the level of parameter triggers.

Record Quantity : Sets the number of times snapshot is repeated.

ACTIVE KEY

Applies the trigger when the ECU data is higher than or equal to the set value.

Applies the trigger when the ECU data is lower than or equal to the set value.

Applies the trigger when the ECU data is equal to the set value.

Sets the trigger level.

Applies the trigger when all set conditions are satisfied.

Applies the trigger when some of the set conditions are satisfied.

Returns to the trigger data selection screen. (Trigger data can be added.)

Returns to the Snapshot operation setting screen.

Value setting screen

=

AND

OR

Add

Exit

- 53 -


With the data list manager, you can change display data lists and other data set in measurement groups and create new measurement groups.The procedure for starting the data list manager is as follows.

1. To change the display data, select the related measurement group on the data list screen.

2. In the data list screen [Function] menu, touch [Data List Manager]. Or touch the function button.The data list manager screen is displayed.

3. Change the display data on the data list manager screen.

Data List Manager

Data list screen [Function] Menu list

Function buttons

With the display data selected When the display data is decided

- 54 -


ACTIVE KEY

Help functionWhen [Help] is touched in the menu bar, the help screen is displayed and guidance concerning the data list is shown.To close the help screen, touch [OK] at the top right of the screen.

Adds only the data selected in the item list to the custom list.

Adds all the data in the item list to the custom list.

Deletes all the data in the custom list.

Deletes only the data selected in the custom list.

Moves the data selected in the custom list up one space.

Moves the data selected in the custom list down one space.

Sets the custom list data.

Returns the display to the previous screen.

Save

OK

Help screen

- 55 -


The Active Test is a function to forcibly drive relays, actuators, solenoids, etc.

Selects the Active Test items.

1. From the main menu buttons, touch .Alternatively, from the [Function] menu list, touch [Active Test].The Active Test item select screen is displayed.

2. On the Active Test item select screen, select the test items and then touch .The Active Test starts.

ACTIVE KEY

Active Test

NOTEYou can not use the Active Test in the GST mode.

Active Test Item Selection

NOTEAlthough the Active Test item select screen may sometimes show no test items, this is not a malfunction. Even with the same vehicle computer (ECU), some types of vehicle may have no testable items.

Starts the Active Test for the selected items.This is not valid unless a test item has been selected.

Active Test

Enter

[Function] menu list Active Test item select screen

Main Menu Buttons

Enter

- 56 -


Actuators are driven by the control box.During an Active Test, the data list can be displayed simultaneously and measurement groups selected from the list box.

The signal shown in a pink cell is the one in the Active Test drive condition.

Active Test Execution

CAUTIONDuring the Active Test, the signal in the drive condition is monitored and cannot be removed from the selection list.

NOTENo data list can be displayed during an Active Test according to the ECUs selected (ABS,etc.).

Active Test execution screen

Signal select screen Data list manager

- 57 -


Control boxWhen an Active Test is executed, the control box for varying the drive value is displayed under the test item, so it is possible to set the Active Test drive value.There are two types of control box as follows, and the system switches automatically among them according to the test items selected.

Binary typeThe drive value is varied between two values (ON/OFF, etc.).Analog change typeThe drive value is changed in analog.Value selection typeIf the drive value button being displayed is touched, the test is executed with that value.One selection drive typeAfter selecting the drive value, touch to start and to stop.

Help functionWhen [Help] is touched in the menu bar, the help screen is displayed and guidance concerning the Active Test being executed is shown.To close the help screen, touch [OK] at the top right of the screen.

Enable Disable

Analog change type

Binary type

Value selection typeOne selection drive type

Help screen

- 58 -


The SUZUKI SDT has a utility with various functions.The procedure for starting the utility is as follows.

1. From the main menu buttons, touch .Alternatively, touch [Utility] in the [Function] menu list.The utility function select screen is displayed.

2. Touch the function to be executed on the utility function select screen.

The functions that can be selected using the utility function select screen are indicated below. The functions that are supported vary by the vehicle being diagnosed.

*ESP® is a registered trademark of Daimler Chrysler AG.

Utilities

Function Reference page

Keyless start system P.60

VIN Registration P.62

Readiness Test P.67

Retrieving All DTCs P.68

Hydraulic control test P.72

Sensor Calibration P.76

ESP® Function Setting P.77

TPS ID registration P.79

Clear Air Bag Information P.80

Dead Lock Control Test P.82

Clear Lock P.84

Clear Lamp P.85

Oscilloscope P.127

Voltage Meter P.118

Utility

[Function] Menu list

Main Menu Buttons

Utility function select screen

- 59 -


This function is used when registering the steering lock unit ID code in a Keyless start control module. If keyless start control module which was used in another vehicle has been installed, or steering lock unit was replaced, register the ID using this function. For vehicles not equipped with immobilizer control system, ID registration is not necessary.

1. Make sure that the ignition switch is turned to ON position with engine stopped. Then touch

on the utility function select screen.The function select screen is displayed.

2. Select [Keyless start registration] and touch on the function select screen.The registration preparation screen is displayed.

Keyless start system (For vehicle not equipped with Immobilizer control system)

Keyless start system

Next

Utility function select screen Function select screen

- 60 -


3. Check the content on the registration preparation screen and then touch .When registration is complete, the registration completion screen is displayed.

Next

Registration preparation screen Registration completion screen

- 61 -


This function is used for registering VIN into the replaced ECM/PCM.

1. Make sure that the ignition switch is turned to ON position with engine stopped. Then touch

on the utility function select screen.The registration preparation screen is displayed.

Saving the VINThis VIN saving procedure is carried out to store the VIN of the previous ECM/PCM in the SUZUKI SDT. This saved VIN is used in the VIN registration procedure. See page 64. By using this saving procedure, input errors by technicans can be avoided.

VIN Registration (For models on and after 05MY in North American market)

NOTEIf the ECM/PCM to be changed has been damaged, there are cases where the VIN cannot be stored in the SUZUKI SDT. In such cases, stop the VIN storage procedure, and perform the VIN registration procedure shown on page 64.

VIN Registration

Utility function select screen Registration preparation screen

- 62 -


1. Touch on the registration preparation screen.The VIN store screen is displayed and the VIN is stored in the SUZUKI SDT.

2. On the VIN store screen, after touching , follow the Service Manual for each vehicle to replace the ECM/PCM. After the new ECM/PCM has been installed, carry out the VIN registration procedure on the page 64.

ACTIVE KEY

NOTECarry out the procedure before replacing ECM/PCM with new one.

The VIN registered in the currently installed ECM/PCM is stored in the SUZUKI SDT.

Store

VIN store screen

Exit

Store

- 63 -


VIN registrationAfter replacing the ECM/PCM with new one, use the VIN registration procedure indicated below.

1. After checking the content on the registration preparation screen, touch .The VIN registration screen is displayed.

2. Enter the VIN on the VIN registration screen.There are three different ways to enter the VIN.2-1. Reading the VIN stored in the SUZUKI SDT

2-1-1. Touch on the VIN registration screen if you have stored VIN registerd in old ECM/PCM in the SUZUKI SDT referring "Saving VIN" section.The VIN stored in the SUZUKI SDT is displayed on the screen.

2-2. Reading the VIN stored in the replaced ECM/PCM2-2-1. Touch on the VIN registration screen.

The VIN registered in the ECM/PCM is displayed.

NOTEIf the VIN is not stored in the SUZUKI SDT, it is not possible to touch .On the VIN input screen, it is possible to edit the VIN.Reference: 2-3. Entering the VIN using the VIN input panel.

NOTEUsing the VIN input screen, it is possible to edit the VIN.Reference: 2-3. Entering the VIN using the VIN input panel.

Next

VIN registration screen

Upload

Upload

Read

- 64 -


2-3. Entering the VIN using the VIN input panel.2-3-1. Touch on the VIN registration screen.

The VIN input screen is displayed.

2-3-2. On the VIN input screen, after entering the VIN, touch .On the VIN registration screen, the VIN entered is displayed.

NOTEBe sure to enter all 17 of the digits.

The VIN can be cancelled by touching .When an input cell is touched, the curser moves to the location touched.

Input

The VIN input screen

OK

Clear

- 65 -


3. After entering the VIN, in the VIN registration screen, touch .The registration completion screen is displayed.

ACTIVE KEY

CAUTIONIf the VIN entered is not valid, the input error screen or the VIN confirmation screen is displayedIf the input error screen is displayed, re-enter the 17 digit VIN.If the VIN confirmation screen is displayed, after confirming the VIN, re-enter the correct VIN.The VIN registration procedure can be terminated by touching .

The VIN stored in the SUZUKI SDT is displayed on the screen.

The VIN stored in the currently installed ECM/PCM is displayed.

The VIN can be entered using the input panel.

Next

Exit

Registration completion screen

Input error screen

VIN confirmation screen

Upload

Read

Input

- 66 -


This function is used to monitor the various conditions related to the on-board tests carried out by the ECM/PCM.

1. Touch on the utility function select screen.The information display screen is displayed.

Readiness Test

Readiness Test

Utility function select screen Information display screen

- 67 -


This function is used to read the DTCs from all of the vehicle's systems which have readable DTC functions.

1. Touch on the utility function select screen.The verification dialog box is displayed.

2. Touch in the verification dialog box.The search dialog box is displayed, and the DTCs of each system are checked.

When the DTC checks for all of the systems have been completed, the completion dialog box will be displayed.

Retrieving All DTCs

NOTETouching on the search screen will cause the DTC check for the system being searched for at that time to be terminated and a DTC check for the next system to be started.

Retrieving All DTCs

Verification dialog box

Yes

Search dialog box

Skip

Completion dialog box

- 68 -


3. Touch in the completion dialog box.The result display screen is displayed.

When displaying DTC details

4. Touch after selecting the system for which you would like to verify details from the result display screen.The details display screen is displayed.

NOTESystems displayed with gray colored cells indicate unconnected systems.

The DTC numbers for systems in which has been touched will be indicated with a [-] regardless of the existence of DTCs or not.

OK

Result display screen

Skip

Details

Details display screen

- 69 -


To delete all of the DTCs in all the systems at once.

4. Touch on the result display screen.The delete verification dialog box is displayed.

5. Touch in the delete verification dialog box.The deletion in progress dialog box is displayed and DTC items for each system begin to be deleted.

Once all of the DTCs of the systems have been deleted, the deletion completed dialog box will be displayed.

NOTEThere may be occassions where the option select screen is displayed in order to narrow down the number of systems.Select items suited to the vehicle's specifications.The operations required for the details display screen are the same as for the DTC functions.

Touch to return to the result display screen from the details display screen.Exit

Clear All

Delete verification dialog box

Yes

Deletion in progress dialog box

Deletion completed dialog box

- 70 -


6. Touch in the deletion completed dialog box.The recheck verification dialog box is displayed.

NOTETouch to carry out DTC checks for the DTCs in all of the systems again.

Touch to terminate total diagnosis for all of the systems.

OK

Recheck verification dialog box

Yes

No

- 71 -


This function is used to make sure that the brake piping is correctly installed after replacement of the ABS(ESP®) hydraulic unit/control module etc.

1. Touch on the utility function select screen.The vehicle condition confirmation screen is displayed.

Hydraulic control test

NOTECarry out the operation check with a partner.You cannot carry out the operation check when the battery voltage is below 9.5V with the engine stopped.After checking the battery voltage, carry out the operation check.

Hydraulic control test

Vehicle condition confirmation

screen

- 72 -


2. Touch on the vehicle condition confirmation screen.The function select screen is displayed.

3. After selecting a check on the function select screen, touch .The wheel select screen is displayed.

NOTEIf the vehicle does not support "Pressurization check", it is not displayed.

NOTEFor vehicles equipped with a 3CH-controlled ABS, "Rear" is displayed instead of "Right Rear"/"Left Rear".In this case, select "Rear" to carry out the depressurization check on both the right and left rear wheels.

Next

Function select screen

Next

Wheel select screen

- 73 -


4. After selecting a wheel to be checked on the wheel select screen, touch .The check execution screen is displayed.

5. Touch when the check displayed on the check execution screen is being carried out.The checking dialog box is displayed, and the operation check starts.When the operation check is complete, the check completed screen is displayed.

NOTECarry out the check with one operator operating the SUZUKI SDT and the brake pedal from the driver's seat while the other rotates the tire from outside the vehicle.Both operators need to carry out the check while timing the operations by signaling to each other.For full-time 4WD vehicles that have coupling resistance, you can carry out the depressurization check by rotating the tire with more force.

Next

Check execution screen

(Depressurization check)

Check execution screen

(Pressurization check)

Next

Checking dialog box

Check completed screen

- 74 -


6. Touch on the check completed screen.The wheel select screen is displayed.

NOTEIf you intend to carry out the check on another wheel continuously, follow the procedure beginning with step 4 after selecting the wheel.

You can return to the utility function select screen by touching on the check completed screen.

Next

Wheel select screen

Exit

- 75 -


This function is used to calibrate all the sensors used in the ESP® at the same time afterreplacement of the ESP® hydraulic control unit etc.


2. Touch on the vehicle condition confirmation screen.The calibrating dialog box is displayed, and the calibration starts.When the calibration is complete, the calibration completed screen is displayed.

3. Touch on the calibration completed screen.This returns the display to the utility function select screen.

Sensor Calibration

NOTEItems displayed on the screen may differ depending on the vehicle.

Sensor Calibration


screen

Next

Checking dialog box

Calibration completed screen

Exit

- 76 -


This function is used to stop ESP® functions and perform tests on the speedometer etc.

1. Touch on the utility function select screen.The control switching screen is displayed.

2. After selecting the control mode (Activation/Deactivation) on the control switching screen, touch .

When you have selected "OFF (Deactivation)" on the control switching screen:The control status confirmation screen is displayed, and the ESP® function switches to deactivation mode.

ESP® Function Setting

NOTEDeactivation mode remains active until the ignition switch is turned to OFF.

ESP® Function Setting

Control switching screen

Next

Control status confirmation

screen

- 77 -


When you have selected "ON (Activation)" on the control switching screen:The control status confirmation screen is displayed.

3. Touch on the control status confirmation screen.This returns the display to the utility function select screen.

Control status confirmation

screen

Exit

- 78 -


This function is used to register the tire pressure sensor (TPS) IDs.

1. Touch on the utility function select screen.The ID registration preparation screen is displayed.

2. After performing the steps displayed on the ID registration preparation screen, touch .The ID registration execution screen is displayed, and the TPS ID registration starts.When the TPS ID registration is complete, the ID registration completion screen is displayed.

3. Touch on the ID registration completion screen.This returns the display to the utility function select screen.

TPS ID registration

NOTEIf TPS ID registration is not complete within 90 seconds, it will be identified as an out of time error and TPS ID registration will be stopped.

TPS ID registration

ID registration preparation

screen

Next

ID registration execution screen ID registration completion screen

Exit

- 79 -


This function is used to clear the air bag information from the BCM.

1. Touch on the Utility function select screen.The Data List confirmation screen is displayed.

2. Touch on the Data List confirmation screen.The Vehicle condition confirmation screen is displayed.

Clear Air Bag Information

Clear air bag information

Data List confirmation screen

Next


screen

- 80 -


3. Touch on the Vehicle condition confirmation screen.An execution dialogue box is displayed and the clearing of the air bag information starts.When the clearing is complete, the Clearing completed screen is displayed.

4. Touch on the Clearing completed screen.This returns the display to the Utility function select screen.

Next

Execution dialogue box

Clearing completed screen

Exit

- 81 -


This function is used to turn ON/OFF all the door locks at the same time.

1. Touch on the Utility function select screen.The Vehicle condition confirmation screen is displayed.

2. Touch on the Vehicle condition confirmation screen.The Test item select screen is displayed.

3. After selecting a test item on the Test item select screen, touch .

Dead Lock Control Test

Dead Lock Control Test


screen

Next

Test item select screen

Next

- 82 -


If "Dead Lock Set Test" is selectedAn execution dialogue box is displayed and all the doors are locked.

If "Dead Lock Clear Test" is selectedAn execution dialogue box is displayed and all the doors are unlocked.

4. Touch on the Testing completed screen.This returns the display to the Test item select screen.

NOTETo end the Dead Lock Control Test function, touch on the Test item select screen.The Dead Lock is released, and the Dead Lock Control Test function ends.


Testing completed screen


Testing completed screen

Next

Cancel

- 83 -


This function is used to release the near-deploy lock.


2. Touch on the vehicle condition confirmation screen.The execution dialogue box is displayed, and the releasing of the near-deploy lock starts.Once the releasing of the near-deploy lock is complete, the completion screen is displayed.

3. Touch on the Completion screen.This returns the display to the Utility function select screen.

Clear Lock

Clear Lock

Vehicle Condition Confirmation

Screen

Next


Completion Screen

Exit

- 84 -


This function is used to turn the warning lamp off.


2. Touch on the vehicle condition confirmation screen.The execution dialogue box is displayed, and the warning lamp goes out.Once the warning lamp goes out, the completion screen is displayed.

3. Touch on the Completion screen.This returns the display to the Utility function select screen.

Clear Lamp

Clear Lamp

Vehicle Condition Confirmation

Screen

Next


Completion Screen

Exit

- 85 -


The procedure for starting the utility is as follows.

1. From the main menu buttons, touch .Alternatively, touch [Utility] in the [Function] menu list.The utility function select screen is displayed.

2. Touch the function to be executed on the utility function select screen.

The functions that can be selected from the utility function select screen that appears after having selected the GST mode are as follows. Be advised that the supported functions may differ depending upon the vehicle targeted for diagnosis.

Utilities (GST Mode)

NOTEThe utility functions that can be used with the GST mode may have different categories and operating methods than the utility functions that can be operated in the SUZUKI mode.

Function Reference page

Readiness Test P.87

VIN (Vehicle Identification Number) Display P.87

Cal.ID (Calibration Identifications) Display P.88

CVN (Calibration Verification Numbers) Display P.88

Utility

[Function] Menu list Utility function select screen

Main Menu Buttons

- 86 -


This function is used to monitor the state of affairs of varied on-board tests carried out with a power train.


This function is used to display the VIN.


Readiness Test

VIN (Vehicle Identifications Number) Display

System readiness test results


Vehicle Identifications Number (VIN)


- 87 -


This function is used to display the vehicle’s Cal.ID.


This function is used to display the vehicle’s CVN.


Cal.ID (Calibration Identifications) Display

NOTEThe Cal.ID (Calibration Identifications) is a code that is used to categorize software items which are installed onto on-board vehicle computers (ECU).

CVN (Calibration Verification Numbers) Display

NOTECVN (Calibration Verification Numbers) is used to verify the compatibility of software items which are installed onto on-board vehicle computers (ECU).

Calibration Identifications (Cal.ID)


Calibration Verification Numbers (CVN)


- 88 -

4 Diagnostics Functions (for screen type 2)


4 Diagnostics Functions (for screen type 2)This section describes the operation to be performed when the following menu screen is displayed after the vehicle has been selected.

DTC is stored in the vehicle computer (ECU) internal memory when a trouble occurs.Checking DTC can aid in specifying the cause of the trouble.

Displays DTC (Current/History DTC) for the vehicle that has been selected from the vehicle selection screen.The procedure for displaying the DTC (Current/History DTC) is as follows.

1. Touch on the menu screen.The DTC menu screen is displayed.

DTC Check

DTC (Current/History DTC) Display

Menu screen (for screen type 2)

Trouble Codes

DTC menu screenMenu screen

- 90 -


2. Touch on the DTC menu screen.The DTC list is displayed on the DTC display screen.

ACTIVE KEY

The procedure for clearing the DTC is as follows.

1. Touch on the DTC display screen.The DTC clear screen is displayed.

2. On the DTC clear screen, touch .The DTC is deleted.

Switches between the "Current DTC" and "History DTC" screens.

Clears the DTC stored in the vehicle computer (ECU). Reference: Page 36

DTC Clear

Current/History DTC

DTC display screen

(History DTC)

DTC display screen

(Current DTC)

<< >>

Clear DTCs

Clear DTCs

ENTER

DTC display screen DTC clear screen

- 91 -


Displays freeze frame data related to the DTC.ECU data recorded when the DTC is generated

The procedure for displaying freeze frame data is as follows.

1. Touch on the DTC menu screen.The freeze frame data display screen is displayed.

Freeze Frame Data Display

Freeze Data

DTC menu screen Freeze frame data display screen

- 92 -


Displays the DTC (Pending DTC) for the vehicle that has been selected from the vehicle selection screen.The procedure for displaying the DTC (Pending DTC) is as follows.

1. Touch on the DTC menu screen.The Pending DTC list is displayed on the DTC display screen.

ACTIVE KEY

DTC (Pending DTC) Display

Clears the DTC stored in the vehicle computer (ECU). Reference: Page 36

Pending DTC

DTC menu screen DTC display screen

(Pending DTC)

Clear DTCs

- 93 -


Vehicle computer (ECU) data can also be monitored numerically or in graph form and snapshots can be recorded.

Displays the ECU data for the system selected on the system select screen.The procedure for displaying the ECU data is as follows.

1. Touch on the menu screen.The data list screen is displayed.

ACTIVE KEY

Data List

Data List Display

NOTEThe number of the items displayed on the menu screen depends on the vehicle.

Changes the unit of the ECU data.

Stops the updating of screen display.

Changes the buttons displayed on the bottom of screen.

Displays the DTC display screen.

Data List

Menu screen Data list screen

CHANGE UNITS

FREEZE FRAME

MORE

READ DTC

- 94 -


This function is used to display the selected ECU data locked on the top of the screen.Even if the screen is scrolled, the locked data is always displayed on the top of the screen.

1. Touch twice the ECU data to be locked on the data list screen.The ECU data touched will move to the top of the screen and the display is locked.

2. After touching on the data list screen (Pre-Lock), touch twice the ECU data to be unlocked.The ECU data touched will be unlocked, and it will return to the original display position.

Pre-Lock Function

NOTEA maximum of 7 ECU data can be moved.

Data list screen Data list screen (Pre-Lock)

Unlock Items

- 95 -


Displays only the selected ECU data.

1. Touch on the menu screen.The data select screen is displayed.

2. Touch twice the ECU data to be displayed on the data select screen."*" is displayed at the left side of the selected ECU data.

Data List Selection

NOTEA maximum of 14 ECU data names can be selected.By touching twice the selected ECU data name, "*" disappears and the selection is cleared.

Data List - Select

Menu screen Data select screen

Data select screen (After selection)

- 96 -


3. Touch on the data select screen (After selection).The data list screen is displayed.

ACTIVE KEY

Clears all the ECU data selections.


ACCEPT

Data list screen

CLEAR ALL

FREEZE FRAME

- 97 -


Displays the selected ECU data in a line graph.

1. Touch on the menu screen.The data select screen is displayed.

2. Touch twice the ECU data to be displayed on the data select screen."*" is displayed at the left side of the selected ECU data.

Graph Display

NOTEA maximum of 4 ECU data names can be selected.By touching twice the selected ECU data name, "*" disappears and the selection is cleared.

Data Graph

Menu screen Data select screen

Data select screen (After selection)

- 98 -


3. Touch on the data select screen (After selection).The graph display screen is displayed.

ACTIVE KEY

Clears all the ECU data selections.

Displays a graph for each selected ECU data.Engine: Abbreviation of ECU data

Stops the updating of graph display. Graph display is restarted by pressing this key again.

ACCEPT

Graph display screen

CLEAR ALL

Engine

ENTER

- 99 -


Records the monitor results of the ECU data.

Trigger by Any DTCRecords the data by triggering when any DTC was detected.

1. Touch on the menu screen.The snap shot function screen is displayed.

2. Touch on the snap shot function screen.1) The data list screen is displayed, and the DTC detection starts.

Snapshots

NOTEA maximum of 6 snap shot data can be recorded.If more than 6 data is stored, the oldest data is overwritten in order.If the snap shot data is locked, that data is not overwritten.Reference: Page 109 Snap shot data lock (Chapter 4 Diagnostics Functions (for screen type 2)/Data List)

Snap Shot

Menu screen Snap shot function screen

Trigger By Any DTC

Data list screen

- 100 -


2) If the DTC is detected, the progress bar is displayed at the bottom of the screen and the recording of the snap shot data is started.

3) When the recoding of the snap shot data is complete, the record check screen is displayed.

Data list screen (progress bar)

Record check screen

- 101 -


3. Touch on the record check screen.The record execution screen is displayed.When the recording is completed, the screen automatically returns to the snap shot function screen.

Trigger by Single DTCRecords the data by triggering when the specified DTC was detected.

1. Touch on the snap shot function screen.The DTC code input screen is displayed.

ENTER

Record execution screen

Trigger By Single DTC

DTC code input screen

- 102 -


2. After inputting the DTC code on the DTC code input screen, touch .Reference: Page 23 Software keyboard operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)1) The data list screen is displayed, and the DTC detection starts.

NOTEIf is touched when the nonexistent DTC code was input or DTC code is not input, the error screen is displayed.

ENTER

Data list screen

ENTER

Error screen

- 103 -


2) If the input DTC is detected, the progress bar is displayed at the bottom of the screen and the recording of the snap shot data is started.For the procedure after this step, refer to steps 2) - 3) and 3 of "Trigger by Any DTC" section.


- 104 -


Manual TriggerRecords the data by triggering when the trigger button was pressed.

1. Touch on the snap shot function screen.The data list screen is displayed.

2. Touch on the data list screen.1) The progress bar is displayed at the bottom of the screen and the recording of the snap shot data is started.

For the procedure after this step, refer to steps 2) - 3) and 3 of "Trigger by Any DTC" section.

ACTIVE KEY


Terminates the recording of the snap shot data.


Triggers when the button was pressed.

Manual Trigger

Data list screen

TRIGGER


CHANGE UNITS

STOP

FREEZE FRAME

TRIGGER

- 105 -


Data ReplayReplays the recorded snap shot data.

1. Touch on the menu screen.The snap shot function screen is displayed.

2. Touch on the snap shot function screen.The playback data select screen is displayed.

Snapshot Playback

Snap Shot

Menu screen Snap shot function screen

Replay Data

Playback data select screen

- 106 -


3. After selecting the data to be played back on the play back data select screen, touch .The snapshot data playback screen is displayed.

4. Touch on the snapshot data playback screen.5 button displays are switched.

ENTER

Snapshot data playback screen

MORE

Snapshot data playback screen

- 107 -


ACTIVE KEY

Locks the display of the selected ECU data.Reference: Page 95 Pre-Lock Function (Chapter 4 Diagnostics Functions (for screen type 2)/Data List)

Displays the graph display screen.Reference: Page 98 Graph Display (Chapter 4 Diagnostics Functions (for screen type 2)/Data List)

Moves to the sample time at the trigger point.

Changes the buttons displayed on the screen.


Returns the Sample time.

Advances the Sample time.

Returns the Sample time in 500 msec increments.

Advances the Sample time in 500 msec increments.

Automatically returns the Sample time.

Automatically advances the Sample time.

Moves to the Sample time at the start of recording.

Moves to the Sample time at the end of recording.

ENTER

PLOT

TRIGGER POINT

MORE

CHANGE UNITS

PREV SAMPLE

NEXT SAMPLE

PREV 500ms

NEXT 500ms

AUTO REV

AUTO FORWARD

FIRST SAMPLE

LAST SAMPLE

- 108 -


Snap shot data lockLocks the selected snap shot data to prevent erasing.

1. After selecting the data to be locked on the playback data select screen, touch ."Locked" is displayed at the upper right corner of the selected data, and the data is locked.

Snap shot data erasingErase the selected snap shot data.

1. After selecting the data to be erased on the playback data select screen, touch .The selected data is erased.

NOTEA maximum of 2 data can be locked.

Lock can be cleared by touching after selecting the locked data.

NOTEIf the data is locked, it cannot be erased.

Lock Snapshot

Playback data select screen Playback data select screen (Lock)

Unlock Snapshot

Erase Snapshot

Playback data select screen

- 109 -

5 Saved Data Playback Functions


5 Saved Data Playback FunctionsThe SUZUKI SDT not only has functions for diagnosing breakdowns inreal time, but also has functions that can play back saved data afterwards.The saved data playback functions do not require the SUZUKI SDT andthe vehicle to connect.The onboard/offboard check screen is displayed after the opening screenwhen the SUZUKI SDT is started up.The saved data playback functions are the DTC playback and snapshotplayback functions, and they can be started from the [Function] menu.

Plays back saved DTC data.The procedure for playing back DTC data is as follows.

1. From the [Function] menu list, touch [Saved Data Review].The playback data select screen is displayed and a list of saved DTC data files is displayed.

2. On the playback data select screen, select the DTC data for playback and then touch .When DTC data is selected, file information is displayed in the File Information column.

Touching plays back the selected DTC data.

DTC Playback

NOTE"CID" or "Cal.ID" will be displayed in the File Information column. Their respective meanings are as follows.

CID: After selecting the vehicle in the data stored during the diagnosis in the SUZUKI mode will be displayed.

Cal.ID: The data stored during the diagnosis in the GST mode will be displayed.

Onboard/offboard check screen

Auto

[Function] Menu list Playback data select screen DTC data playback screen

- 111 -


ACTIVE KEY

NOTEThe CID data is shown in the File Information field on the Playback data select screen. CID stands for "Component ID" which is the electronic ID read when the SUZUKI SDT communicates with the ECU. This electronic ID (CID) is used to activate each program in the SDT diagnosis software. Note that it is not the ECU part number.

Opens the selected DTC data and plays it back.

Deletes the selected DTC data.

Displays saved the current DTC data.When there is DTC data, this button is displayed in blue.

Displays saved pending DTC data.When there is pending DTC data, this button is displayed in blue.

Displays saved historical DTC data (past codes).When there is historical DTC data, this button is displayed in blue.

Ends playback data selection. (Playback data select screen)Returns the display to the playback data select screen. (When saved DTC data is played back.)

Current

Pending

History

Exit

- 112 -


Plays back stored snapshot data.The procedure for playing back snapshot data is as follows.

1. From the [Function] menu list, touch [Snapshot Review].The playback data select screen is displayed and a list of saved snapshot data files is displayed.

2. On the playback data select screen, select the snapshot data for playback and then touch the function button.When snapshot data is selected, file information is displayed in the File Information column.

Touching plays back the selected snapshot data.

Snapshot Playback

NOTE"CID" or "Cal.ID" will be displayed in the File Information column. Their respective meanings are as follows.

CID: After selecting the vehicle in the data stored during the diagnosis in the SUZUKI mode will be displayed.

Cal.ID: The data stored during the diagnosis in the GST mode will be displayed.

NOTE"DL" and "AT" may be displayed in the playback data selection screen Function column."DL" means that the snapshot is from the data list, and "AT" means that it was saved while an Active Test was executed.The CID data is shown in the File Information field on the Playback data select screen. CID stands for "Component ID" which is the electronic ID read when the SUZUKI SDT communicates with the ECU. This electronic ID (CID) is used to activate each program in the SDT diagnosis software. Note that it is not the ECU part number.

Auto

[Function] menu list Playback data select screen Snapshot data playback screen

- 113 -


ACTIVE KEY

Displays the playback screen and plays back the data.

Deletes the selected data.

Displays the playback data select screen.

Ends playback data selection. (Playback data select screen)Returns the display to the playback data select screen. (During snapshot data playback.)

Stops playback and returns to the start of the data.

Pauses playback.

Fast forwards the data playback.

Starts the data playback.

Fast rewinds the data playback.

Moves to a point at which the snapshot flag is set and plays back from there.

The playback position can be changed by touching or by moving the scroll bar to the left and right.This bar is only valid during data list playback.

File Open

Exit

- 114 -


When a snapshot flag is set, you can quickly move to the set point during snapshot playback. There are two methods for playback when a snapshot flag has been set.

During normal playback, when a point is reached for which a snapshot flag is set, " " is displayed in red. When the set point is passed, the " " returns to its original color and playback continues." " is touched during playback, the snapshot flag point is displayed. When this point is selected, the " " is displayed in red and snapshot data for the selected point is played back.

The above " " is displayed in red for about 1 second, and the buzzer sounds at this time.

The playback screen when a snapshot flag is set is as follows.

Playback With Snapshot Flag Set

Screen for selecting point

where snapshot flag is set.

Snapshot flag set point

playback screen

- 115 -


ACTIVE KEY

Displays the playback data select screen.

Returns the display to the playback data select screen.

Stops playback and returns to the start of the data.

Pauses playback.

Fast forwards the data playback.

Starts the data playback.

Rewinds the data playback.

Displays the dialog box for selecting the point where a snapshot flag is set.

The playback position can be changed by touching or by moving the scroll bar to be the left and right.This bar is only valid during data list playback.

File Open

Exit

- 116 -

6 Measurement Functions



A voltage meter probe can be connected to the SUZUKI SDT for voltage measurement.

1. From the main menu buttons of the system select screen, touch .The function select screen is displayed.

2. On the function select screen, touch .The voltage display screen is shown and the voltage currently being measured is displayed in real time.

Voltage Measurement Functions

Measurement Function Selection Menu

Utility

Voltage meter

Function select screen Voltage display screenSystem select screen

- 118 -


The voltage display screen is displayed.

ACTIVE KEY

Voltage Display

Displays the waveform display screen. Reference: Page 120

Saves/plays back/deletes screen images. Reference: Page 123

Executes calibration. Reference: Page 122

Ends voltage measurement.

Voltage display screen

Wave Form

Menu

CAL

Exit

- 119 -


The waveform display screen is displayed.

The following operations can be executed on the waveform display screen.The voltage (vertical axis) and time (horizontal axis) range settings can be changed.Waveform updating can be stopped and resumed.Pressing the right function key on the main unit stops waveform updating; pressing it again resumes updating.

Waveform Display

Waveform display screen

- 120 -


ACTIVE KEY

Voltage axis enlargement

The waveform is enlarged vertically each time the button is touched.The current voltage range is displayed at the top of the button.

Voltage axis reduction

The waveform is reduced vertically each time the button is touched.The current voltage range is displayed at the top of the button.

Time axis enlargement

The waveform is enlarged horizontally each time the button is touched.The current time range is displayed at the top of the button.

Time axis reduction

The waveform is reduced horizontally each time the button is touched.The current time range is displayed at the top of the button.

Executes calibration. Reference: Page 122

Returns the display to the voltage display screen.

Saves/plays back/deletes screen images. Reference: Page 123

Ends voltage measurement.

CAL

Meter

Menu

Exit

- 121 -


Calibrates the zero point.

1. Touch on the voltage display screen or the waveform display screen.The calibrating dialog box is displayed.

2. Connect the voltage measurement tester probe to the reference point.

3. On the calibrating dialog box, touch .The calibrating dialog is displayed. When the calibration is complete, the hint dialog box is displayed.Do not remove the probe during calibration.

4. Check the contents of the hint dialog, then touch .When calibration ends, the tip dialog box is displayed automatically.This dialog displays an explanation for stopping/resuming waveform updating using the right function key on the main unit.

Calibration

NOTEThe reference point refers to the point where the black probe of an ordinary voltmeter is connected.EX: When measuring the sensor voltage, connect the black probe to the sensor GND.

When measuring the battery voltage, connect the black probe to the chassis GND.

CAL

Voltage display screen Waveform display screen

OK

Calibrating dialog box Calibrating dialog box

OK

Hint dialog box

- 122 -


Saves/plays back/deletes screen images.

Screen image save

1. Touch on the voltage display screen or the waveform display screen.The file menu screen is displayed.

2. Touch on the file menu screen.The screen image save screen is displayed.

3. The set file name is displayed on the screen image save screen.If this file name is correct, touch .To a different file, input the name of that file and then touch .A comment to be attached to the saved data can be input in the comment column.Reference: Page 23 Software keyboard operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)"File creation date and time_serial number" is set automatically as the file name displayed.

Screen Image Save/Playback/Delete

Menu

Save Screen Copy


File menu screen

SaveSave

Screen image save screen Screen image playback screen

- 123 -


ACTIVE KEY

Executes screen image save processing.

Executes screen image playback/delete processing.


Saves a screen image

Returns the display to the file menu screen.

Save Screen Copy

Open Screen Copy

Exit

Save

Cancel

- 124 -


Screen Image Playback/DeletePlaying back a screen image


2. Touch on the file menu screen.The screen image select screen is displayed.

3. After touching the playback screen image on the screen image select screen, touch .The playback screen for the selected screen image is displayed.

ACTIVE KEY




Plays back the selected screen image.

Deletes the selected screen image.


Menu

Open Screen Copy


File menu screen

Open

Screen image select screen

Screen image playback screen

Save Screen Copy

Open Screen Copy

Exit

Open

Delete

Cancel

- 125 -


Deleting a screen image



3. After touching the screen image for deletion on the screen image select screen, touch .The selected screen image is deleted.

ACTIVE KEY







Menu

Open Screen Copy


File menu screen

Delete


Save Screen Copy

Open Screen Copy

Exit

Open

Delete

Cancel

- 126 -


To use the oscilloscope function, it is necessary to connect the optional oscilloscope cartridge.The oscilloscope probes can be connected to the SUZUKI SDT to observe the voltage waveform for the signals input to the channels.Do not connect the AC/DC adapter to the SUZUKI SDT, when using the oscilloscope function.

1. From the main menu buttons of the system select screen, touch .The function select screen is displayed.

2. On the function select screen, touch .The oscilloscope measurement screen is displayed.

ACTIVE KEY

Oscilloscope Functions

Oscilloscope Measurement Menu

Saves/plays back/deletes screen images and measurement condition setting data. Reference: Page 134

Ends the oscilloscope function.

Displays the trigger menu screen. Reference: Page 130

Utility

Oscilloscope

Function select screen Oscilloscope measurement

menu screen


Menu

Exit

Trigger

- 127 -


The following operations can be executed on the waveform display screen.The voltage (vertical axis) and time (horizontal axis) range settings can be changed.The ground level (0V position) can be set for the selected channel.

Waveform updating can be stopped and resumed.Pressing the right function key on the main unit stops waveform updating; pressing it again resumes updating.

Waveform Display

NOTEThe voltage (vertical axis) range and ground level (0V position) are set for the selected channel.

Waveform display screen

- 128 -


ACTIVE KEY

The channel for the voltage (vertical axis) range and ground level (0V position) is set to "Ch1". When this is selected, the button is displayed in blue.

The channel for the voltage (vertical axis) range and ground level (0V position) is set to "Ch2". When this is selected, the button is displayed in blue.

Saves/plays back/deletes screen images and measurement condition setting data.Reference:

Ends the oscilloscope function.

Displays the trigger menu screen. Reference: Page 130

Voltage axis enlargement

Vertically enlarges the waveform for the selected channel.The current voltage range is displayed to the right of the selected channel.

Voltage axis reduction

Vertically reduces the waveform for the selected channel.The current voltage range is displayed to the right of the selected channel.

Time axis enlargement

The waveform is enlarged horizontally each time the button is touched.The current voltage time range is displayed at the top of the button.

Time axis reduction

The waveform is reduced horizontally each time the button is touched.The current voltage time range is displayed at the top of the button.

Raises the ground level (0V position) for the selected channel.

Lowers the ground level (0V position) for the selected channel.

Ch1

Ch2

Menu

Exit

Trigger

- 129 -


Detailed settings can be performed for a parameter trigger.Trigger channel settingTrigger mode settingTrigger level settingTrigger slope switchingTrigger point setting

1. On the oscilloscope measurement menu screen, touch .The trigger menu screen is displayed.

ACTIVE KEY

Message dialog boxWhen the trigger menu is exited, the message dialog box on the right is displayed automatically.This dialog box displays an explanation of stopping/resuming waveform updating using the right function key on the main unit.

Trigger Menu

Exits the trigger menu and displays the message dialog.

Trigger

Oscilloscope measurement menu screen

Trigger menu screen

Exit

- 130 -


Trigger channel settingSwitches the trigger channel.The selected button is displayed in blue.

ACTIVE KEY

Trigger mode settingSets the trigger mode.The selected button is displayed in blue.The meanings of the trigger modes are as follows.

AutoThe waveform is displayed regardless of the trigger specification.NormThe waveform is only displayed when the specified trigger is detected. (The waveform is updated when the next trigger is detected.) SingleThe waveform from when the specified trigger is first detected is held (the display is fixed).

ACTIVE KEY

Trigger level settingSets the trigger level.The set trigger level is displayed to the left side of the button.

ACTIVE KEY

Sets the trigger channel to "Ch1".

Sets the trigger channel to "Ch2".

Sets the trigger mode to [Auto].

Sets the trigger mode to [Norm].

Sets the trigger mode to [Single].

Raises the trigger level.

Lowers the trigger level.

Ch1

Ch2

Auto

Norm

Single

- 131 -


Trigger slope switchingSwitches the trigger slope.The selected button is displayed in blue.

ACTIVE KEY

Trigger point settingSets the trigger point.The selected button is displayed in blue.

ACTIVE KEY

Trigger pointsThis section uses the following two examples to explain trigger points.

To observe the waveform from the set trigger point onward, select a trigger point of 10%.

Sets the trigger to the rising edge.

Sets the trigger to the falling edge.

Sets the trigger point to 10%.



10%

50%

90%

- 132 -


To observe the waveform up to the set trigger point, select a trigger point of 90%.

- 133 -


Saves/plays back/deletes screen images and measurement condition setting data.

Screen image save

1. On the oscilloscope measurement menu screen, touch .The file menu screen is displayed.

2. Touch on the file menu screen.The screen image save screen is displayed.

3. The set file name is displayed on the screen image save screen.

If this file name is correct, touch .To save to a different file, input the name of that file and then touch .A comment to be attached to the saved data can be input in the comment column.Reference: Page 23 Software keyboard operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)"File creation date and time_serial number" is set automatically as the file name displayed.

Screen Image Save/Playback/Delete

Menu

Save Screen Copy


File menu screen

SaveSave

Screen image save screen

- 134 -


ACTIVE KEY



Executes save processing of the measurement condition setting data.

Executes the measurement condition setting data playback/delete processing.

Returns the display to the oscilloscope measurement menu.

Saves a screen image


Save Screen Copy

Open Screen Copy

Save Setup Data

Open Setup Data

Exit

Save

Cancel

- 135 -


Screen Image Playback/DeletePlaying back a screen image



3. After touching the playback screen image on the screen image select screen, touch .The playback screen for the selected screen image is displayed."File creation date and time_serial number" is set automatically as the file name displayed.

ACTIVE KEYFor details on , , and see Page 135





Menu

Open Screen Copy


File menu screen

Open

Screen image select screen Screen image playback screen

Save Screen Copy Open Screen Copy Save Setup Data Open Setup Data

Exit

Open

Delete

Cancel

- 136 -


Deleting a screen image



3. After touching the screen image for deletion on the screen image select screen, touch .The selected screen image is deleted.






Menu

Open Screen Copy


File menu screen

Delete



Exit

Open

Delete

Cancel

- 137 -


Saves the measurement condition setting data.


2. Touch on the file menu screen.The measurement condition setting data save screen is displayed.

3. The set file name is displayed on the measurement condition setting data save screen.

If this file name is correct, touch .To save to a different file, input the name of that file, and then touch .A comment to be attached to the saved data can be input in the comment column.Reference: Page 23 Software keyboard operation (Chapter 2 Basic Operations/Basic Operations/Display Operation)"File creation date and time_serial number" is set automatically as the file name displayed.



Saves the measurement condition setting data.


Menu

Save Setup Data


File menu screen

SaveSave

Measurement condition setting

data save screen


Exit

Save

Cancel

- 138 -


Plays back/deletes measurement condition setting data.Playing back measurement condition setting data

1. On the oscilloscope measurement menu screen, touch .The file menu screen is displayed

2. Touch on the file menu screen.The measurement condition setting data select screen is displayed.

3. After touching the playback screen image on the measurement condition setting data select screen,

touch .The playback screen for the measurement condition setting data is displayed."File creation date and time_serial number" is set automatically as the file name displayed.



Plays back the selected measurement condition setting data.

Deletes the selected measurement condition setting data.


Menu

Open Setup Data


File menu screen

Open

Measurement condition setting data

select screen


Exit

Open

Delete

Cancel

- 139 -


Deleting measurement condition setting data


2. Touch on the file menu screen.The measurement condition setting data select screen is displayed.

3. After touching the screen image for deletion on the measurement condition setting data select screen,

touch .The selected measurement condition setting data is deleted.



Plays back the selected measurement condition setting data.

Deletes the selected measurement condition setting data.


Menu

Open Setup Data


File menu screen

Delete

Measurement condition setting data

select screen


Exit

Open

Delete

Cancel

- 140 -

7 Appendix

7 Appendix

7 Appendix

A cleaner is a piece of utility software that clears a variety of installation information, which is stored when PC software (USB driver, SDT-Viewer, and SDT diagnosis software program) is installed onto the PC.Installation problems can be solved by re-installing the PC software after the installation information has been cleared.

If this cleaner is used when installation problems have not occurred, software (PC software) which has been installed correctly will be uninstalled. Be very careful with its use.After the cleaner has been used, be sure to re-install the relevant software (the software for which the installation information has been cleared).

Types of cleanersCleaner for USB driver (WinRTUSB_Cleaner.exe)Clear the installation information for the USB driver that has been installed, by executing "WinRTUSBDriver.exe". This cleaner is used when the following problems occur.

The "Installation completed screen" is not displayed after the execution of the installer program for the USB driver "WinRTUSBDriver.exe". Reference: Page 3PC screen (Communication error) is displayed. Reference: Page 9

Cleaner for SDT-Viewer (SDT_ViewerInstaller_Cleaner.exe)Clear the installation information for the SDT-Viewer that has been installed, by executing "SetupSDTViewer.exe". This cleaner is used when the following problems occur.

The "Installation completed screen" is not displayed after the execution of the installer program for the SDT-Viewer "SetupSDTViewer.exe". Reference: Page 5

Cleaner for SDT diagnosis software program (SDT_ImageInstaller_Cleaner.exe)Clear the installation information for the SDT diagnosis software program that has been installed, by executing "SDT _ImageInstaller.exe". This cleaner is used when the following problems occur.

The "Installation completed screen" is not displayed after the execution of the installer program for the SDT diagnosis software program"SDT_ImageInstaller.exe". Reference: Page 5

About the use of the installation information clear program (cleaner)

Introduction

Precaution

NOTEThe software for which the installation information is to be cleared is different for each cleaner (three types in total).

Before use

- 142 -

7 Appendix

1. Close all applications running on the PC.

2. Double click the execution file for the cleaner.The program is executed and the installation information is cleared automatically.

3. Re-install the software for which the installation information has been cleared by the cleaner.

Operating procedure for the cleaners

CAUTIONThe cleaner to be used will differ, depending on the nature of the problem. Be careful not to make a mistake with the file name.Do not use the PC during the execution of the program."Execution window (command prompt)" is displayed briefly when the program is executed.The screen is closed automatically when the installation information has been cleared.

NOTERefer to the section on installation procedures in this manual for information regarding the installation of each type of software.Reference: Page 3 Installing the software for your PC (Chapter 1 Installation/Installation of the SDT diagnosis

software)The software to be installed will differ, depending on the cleaner used.

When the cleaner for the USB driver has been used:Re-install "WinRTUSBDriver.exe" onto the PC.

When the cleaner for the SDT-Viewer has been used:Re-install "SetupSDTViewer.exe" onto the PC.

When the cleaner for the SDT diagnosis software program has been used:Re-install "SDT_ImageInstaller.exe" onto the PC.

Execution window (command prompt)

- 143 -

1st Ed. April, 20069th Ed. June, 2008

Prepared by

© 2008 All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means,electronic or mechanical, for any purpose, without the express written permission ofSuzuki Motor Corporation.

suzuki sdt operator’s manualtraining.suzukiauto.co.za/sasatrainingdocs/ge01 suzuki...

Documents