stormy stormy cc - clay paky · stormy stormy cc the latest led technology meets the charm of a...

The latest LED technology meets the charm of a classic strobe

INSTRUCTION MANUAL

STORMY C71090STORMY CC C71091

www.claypaky.it

STORMYSTORMY CC

PRELIMINARY

STORMYSTORMY CCThe latest LED technology meets the charm of a classic strobe

PRELIMINARY

Congratulations on choosing a Clay Paky product!We thank you for your choice. Please note that this product and all the others in the rich Clay Paky range, has been designed and manufactured with total quality to ensure excellent performance and best meet your expectations and requirements.

Carefully read this instruction manual and keep in its entirety and keep it safe for future reference. It is essential to know the information supplied in this manual in order to ensure that the fitting is installed, used and serviced correctly and safely.

CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to the other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instructions manual, which must always accompany the fitting.

CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instructions manual at any time and channel list without prior notice.

www.claypaky.it

PRELIMINARY

STORMYSTORMY CCThe latest LED technology meets the charm of a classic strobe

CONTENT

1. Safety Information

2. Unpacking And Preparation

3. Installation And Start-Up

4. Control Panel

5. Menu Setting

5.1 Set Up Menu

5.2 Options Menu

5.3 Information Menu

5.4 Manual Control Menu

5.5 Advanced Menu

6. Maintenance

7. Accessories

8. Technical Data

9. Channels

9.1/A Channel List Stormy

9.2/A Channel Function Stormy

9.1/B Channel List Stormy CC

9.2/B Channel Function Stormy CC

9.3 Duration Channels Details

9.4 Rete Channels Details

10. DURATION time - RATE time (PERIOD) relation

4

5

7

8

10

11

12

13

14

14

15

17

18

19

19

19

20

20

21

22

24

CONTENTS Pag.

PRELIMINARYPRELIMINARY

4

PRELIMINARY

1. SAFETY INFORMATION

SAFETY INFORMATIONSTORMY C71090STORMY CC C71091

• Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare.

• Minimum distance of illuminated objects The projector needs to be positioned so that the objects hit by the beam of light are at least 0.2 metres (8”) from the lens of the projector.

• Minimum distance from flammable materials The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from every point on the surface of the fitting.

• Mounting surfacesIt is permissible to mount the fitting on normally flammable surfaces.

• Maximum ambient temperature Do not use the project if ambient temperature (ta) exceeds 40°C.

• IP20 protection rating The protection rating of the fitting is IP20. The meaning of the protection rating is:

• Protection against electrical shock Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• Connection to the power mains A qualified electrician must perform connection to the power mains. Check that the mains frequency and voltage correspond to the frequency and voltage for which the projector was designed and indicated on the electrical data label. This label also gives the input power. Refer to the latter to evaluate the maximum number of devices to be connected to the mains to avoid overloads.

• External surface temperature The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 100°C (212°F).

• Maintenance Before starting any maintenance work or cleaning the projector, cut off power from the supply mains. After switching off, do not remove any parts of the fitting for at least 10 minutes. The lenses must be mounted and, if visibly damaged, they have to be replaced with genuine spares.

The products to which this manual refers comply with the following European Directives: • 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD) • 2004/108/EC - Electromagnetic Compatibility (EMC) • 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

ta< 40 °C

tc ≤ 100 °C

IP 2 0Not protected against dripping water, rain, splashes or jets of water.

Protected against penetration by solid bodies of over 12mm (0.47”) in diameter.

5

PRELIMINARYSTORMY C71090STORMY CC C71091

2. UNPACKING AND PREPARATION

UNPACKING AND PREPARATION

Fig. 1 - Packing content

1

The latest LED technology meets the charm of a classic strobe

INSTRUCTION MANUAL

STORMY C71090

STORMY CC C71091

www.claypaky.it

STORMY

STORMY CC

PRELIMINARY

6

PRELIMINARY

3. INSTALLATION AND START-UP

INSTALLATION AND START-UP

Fig. 2 - Projector installationThe projector can be installed on the floor, on a truss, on the ceiling or wall. WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request). This must be secured to the projector support structure and then hooked to the fastening point at the centre of the fixture.

2

Continued


1 2

3 4

5

7

PRELIMINARY

3. INSTALLATION AND START-UP

INSTALLATION AND START-UP

Fig. 3, 4 - Connecting and disconnecting the power cord

3

4


8

PRELIMINARY

4. CONTROL PANEL

CONTROL PANEL

5

6

PowerSupply

DMX 512

DMX 5125 PIN

Fig. 5 - Connection to the power mains

Fig. 6 - Connections to the control signal line (DMX)Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 3-pin male/female connectors. A terminating plug must be inserted on the last projector with a resistance of 120 (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield braid and pin 1 of the connectors.

Continued


9

PRELIMINARY

4. CONTROL PANEL

CONTROL PANEL

Menu settings status

If no button is pressed after a wait period (about 60 seconds) the display automatically returns to idle status.Any modified value that has not yet been confirmed with the E key will be cancelled.

7

Fig. 7 - Switching on the projectorThe projector immediately turns on when the power cord is plugged

Clay Paky STORMYSoftware release xxx Adress xxx

Button functions – Menu SET• If pressed in idle status: Cyclically switches between idle status and menu settings. • If pressed while setting a menu: Moves to an upper level without changing anything (exits the function)

Decreases the value displayed (with auto-repetitions), or passes to the next item on the menu. For quick access to the minimum parameter value, press the UP key while holding down the DOWN key.

Increases the value displayed (with auto-repetitions), or passes to the previous item on the menu. For quick access to the maximum parameter value, press the DOWN key while holding down the UP key.

Confirms the displayed value or activates the displayed function or opens the next menu.

SELECT

DOWN

UP

ENTER

S

E


Display inversion

To active this function press at the same time UP and DOWN keys while the display is in standby. The condition is memorized and saved even for the subsequent switching. To return to the initial state repeat the operation again.

10

PRELIMINARY

5. MENU SETTING


Main Menu

SET UP

OPTION

INFORMATION

MANUALCONTROL

TEST

ADVANCED

Level 1

DMX Address

Channel Mode

Fixture ID

Dimmer Curve

Minimum Ton Value

LED mode

Silent Mode

Display

Settings

System Version

Driver diagnostics

DMX Monitor

Fans Monitor

Reset

Channel

Access Code 1234

Level 2

StandardExtended

Curve 1Curve 2

RowBalanceStandardQuiet

Default preset

User preset 1

User preset 2

User preset 3

Strobe firmwareBoot firmwareDriver firmwareCPU boardCPU SN

LED Temperature

Driver Temperature

LED channelRedGreenBlueWhiteIntensityDurationRateMacroBlinder

Power Supply fan speed

RedGreenBlueWhiteIntensityDurationRateMacroBlinderRed

Firmware uploader

Model SetUp

Level 3

Reset to defaultLoad preset 1Save to preset 1Load preset 2Save to preset 2Load preset 3Save to preset 3

CurrentMaximumMinimumCurrentMaximumMinimum

Undefined modelStormyStromy CC

Choices / Values

001 - 512

001 - 255

000-255

On / OffYes / NoYes / NoYes / NoYes / NoYes / NoYes / NoYes / No

CH1 - CH4(R-G-B-W255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000

Yes / No

255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000255bit / 0–100%–000

Yes / No

11

PRELIMINARY

5.1 SET-UP MENU

SET UP - DMX ADDRESS

It allows to set DMX address to be assigned to the projector, it’s possible to select a DMX address between 1 and 512.

> NOTE: : In case of absence of DMX input signal, the displayed projector address flashes.

SET UP - CHANNEL MODE

It allows to set the operation mode of the projector selecting from the following:• Standard Max 7 DMX channels occupied for Stormy CC / max 3 DMX channels occupied for Stormy

• Extended Max 10 DMX channels occupied for Stormy CC / max 6 DMX channels occupied for Stormy.

SET UP – FIXTURE ID

It allows to set a "Fixture ID" to be assigned to the projector, for easier identifcation of the same projector in an installation. It’s possible to select a "Fixture ID" between 1 and 255.


12

PRELIMINARY

5.2 OPTIONS MENUOPTION – DIMMER CURVE

It allows the selection of one of the following two Dimmer curves:• Curve 1• Curve 2

OPTION – MINIMUM TON VALUE

It allows the set the minimum “TON'' duration of strobe flash under which it’s not possible to come down. It’s possible to select a value between 0 and 255.

With the ''Duration'' channel you set the fash duration. At every level of the DMX signal correspondsa duration. The value ''Minimum TON value” represents the level of the DMX channel Duration under whichthe TON value does not change..OPTION – LED MODE

It allows the selection of one of the following two methods of LEDs management

• Row RGBW channels are independent .

• Balance RGBW components are optimized to have a white color with maximum light output

OPTION – SILENT MODE

It allows the selection of one of the following two alternatives:

• Standard Maximum fans’ speed; therefore maximum noise level and maximum light output of the LEDs.• Quiet It reduces the fans’ speed and, as a consequence, the noise; the maximum brightness of the LEDs. It reduces also subject to decrease according to the conditions of use (ambient temperature, used effect type).

OPTIONS - DISPLAY

The enabled DISPLAY option (ON) allows to reduce the display backlight on the machine, after a 30 seconds in standby mode. To restart is enough to press any key. Select OFF to disable this option.

OPTIONS - SETTING

It allows to save in the machine memory 3 different settings of the options menu items and its submenus:• User preset 1• User preset 2• User preset 3- Load preset 1, 2 o 3: It is used to display a previously confguration saved by the user.- Save to preset 1, 2 o 3: It is used to save the current confguration set by the user.

• Default preset It allows to reset to the default values (factory settings) on all the voices of the option menu and of therelated submenus


13

PRELIMINARY

5.3 INFORMATION MENUINFORMATION MENU – SYSTEM VERSION

It allows to display the firmware/hardware versions of installed machine components:Strobo firmware Strobo application firmwareBoot firmware Safety softwareDriver firmware Driver application firmwareCPU board Hardware revision of CPU BoardCPU SN Serial number of CPU Board

INFORMATION MENU – DRIVER DIAGNOSTIC – LED TEMPERATURE

It allows to display some details about the functionality of the card/cards and LEDs:• Current Instantly detected operating temperature• Maximum Maximum detected temperature• Minimum Minimum detected temperature

INFORMATION MENU – DRIVER DIAGNOSTIC – DRIVER TEMPERATURE

It allows to view some details about the functionality of the driver card for LED:• Current Instantly detected operating temperature• Maximum Maximum detected temperature• Minimum Minimum detected temperature

INFORMATION MENU – DRIVER DIAGNOSTIC – LED CHANNEL

It displays the diagnostics from the driver card: for each of the 4 channels a SYSTEM information and a ERROR information is reported (the decoding is specifed in the driver’s specifcations).

INFORMATION MENU – DMX MONITOR

It allows to visualize the DMX input level (in bits or as a percentage) of each channel of the projector (value Between 0 and 255 bit or between 0 and 100%).

INFORMATION MENU – FANS MONITORIt allows to display the rotation speed (RPM Speed) of the fans installed on the machine.PwrSp = Power Supply fans.


14

PRELIMINARY

5.4 MANUAL CONTROL MENU

5.5 ADVANCED MENU

MANUAL CONTROL – RESET

It allows to reset the projector’s CPU in case of anomalies.

MANUAL CONTROL – CHANNEL

It allows to set a value in bit to the channels, from the projector control panel for manual control of each effect without the need of a DMX input signal (values between 0 and 255 bits).

> NOTE: To access to the Advanced menu (only recommended for experienced users), you need to set the access code 1234.

ADVANCED MENU – FIRMWARE UPLOAD

It allows to transfer the firmware from one projector to the others connected to it.

ADVANCED MENU – MODEL SETUP

It allows to change the projector's model set, selecting among the available:• Undefined• Stormy• Stormy CC


15

PRELIMINARY

6. MAINTENANCE

MAINTENANCE

1

2 Fuses 6.3 x 32 mm 12AT (p/n FUS001)

8

Fig. 8 - Fuses replacing Each product has 2 fuses associated with the main power cord connection.

Continued


16

PRELIMINARY

6. MAINTENANCE

MAINTENANCE

9

Fig. 9 - Periodic cleaning To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humidity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations: • General cleaning of internal parts. • General visual check of internal parts, cabling, mechanical parts, etc. • Electrical, photometric and functional checks; eventual repairs.

IMPORTANT: Cleaning transparent cover Only use neutral soap and water to clean the transparent cover then dry it carefully with a soft, non-abrasive cloth. (WARNING: the use of alcohol or any other detergent could damage the transparent cover.)

Parts requiring frequent cleaning.


17

PRELIMINARY

7. ACCESSORIES

ACCESSORIES

Fig. 10 - Bandoors - C71116


10

18

PRELIMINARY

8. TECHNICAL DATA

TECHNICAL DATASTORMY C71090STORMY CC C71091

462(18.18")

303(11.93")

152(5.98")

305(12.01")

7.2 Kg (15.13 Ibs)

Led color temperature 5700K

Cooling Forced ventilation with axial fans.

User interface - LCD display 3 lines- 4 Membrane buttons

Connection - AC power input/output: Neutrik PowerCon- DMX data in/out: 5-pin locking XLR

External power Full range 100-240V 50-60Hz, PowerCon connector

Input Power 850 VA

Body - Body extruded in black anodized aluminium

Weight 7.2 Kg (15.13 Ibs)

Protection rating IP20

Working position Work in any position

CE Marking CE MarkingComplies with the following European Directives- 2006/95/EC (LVD)- 2004/108/EC (EMC)- 2011/65/EU (RoHS)

19

PRELIMINARY

9. 1/A CHANNEL LIST _ STORMY

9.2/A CHANNEL FUNCTION _ STORMY

STORMY C71090 CHANNELS

CHANNEL CHANNEL MODE

STANDARD EXTENDED

1 INTENSITY INTENSITY2 DURATION DURATION3 RATE RATE4 - MACRO 5 - SPEED6 - OFFSET

Channel ModeStandard Extended

DMXValue

0 - 255

0 - 255

0 - 5

6 - 255

Function

INTENSITYLight output linearly increases from off to maximum brightness

DURATIONLight time (versus dark time) linearly increasesfrom shorter time (2.5msec) to longer time (650msec)See details in a following dedicated table.IMPORTANT:Duration Time must be lower than Rate Time (Period) for flashing.If Duration Time is equal or greater than Rate Time (Period) the light is continuously on.

RATELight OFF

Flashing at linearly variable frequencyfrom low: (~0.3 flashes/sec or 1 flash every period of 3.5sec)to high (25 flashes/sec or 1°flash every period of 40msec)See details in a following dedicated table.

MACRO

SPEED

OFFSET

20

PRELIMINARY

9. 1/B CHANNEL LIST _ STORMY CC

STORMY CC C71091

9.2/B CHANNEL FUNCTION _ STORMY CC

CHANNELS

123456789

1011121314

STANDARD

REDGREENBLUEWHITEINTENSITYDURATIONRATE-------

EXTENDED

REDGREENBLUEWHITEINTENSITYDURATIONRATEMACROSPEEDOFFSET----

INDEPENDENT

REDDURATIONRATEGREENDURATIONRATEBLUEDURATIONRATEWHITEDURATIONRATEINTENSITYMASK

CHANNEL MODECHANNEL

Standard

1

2

3

4

5

6

7

1

2

3

4

5

6

7

ExtendedDMXValue

Channel mode Function

RED

Red colour linearly increases from no-light to maximum intensity

GREEN

Green colour linearly increases from no-light to maximum

intensity

BLUEBlue colour linearly increases from no-light to maximum intensity

WHITE

White colour linearly increases from no-light to maximum intensity

INTENSITYLight output linearly increases from off to maximum brightness

DURATION

Light time (versus dark time) linearly increases

from shorter time (2.5msec) to longer time (650msec)

See details in a following dedicated table.

IMPORTANT:

Duration Time must be lower than Rate Time (Period) for

flashing. If Duration Time is equal or greater than Rate Time

(Period) the light is continuously on.

RATE

Light OFF

Flashing at linearly variable frequency

from low: (~0.3 flashes/sec or 1 flash every period of 3.5sec)

to high (25 flashes/sec or 1°flash every period of 40msec)

See details in a following dedicated table.

0 - 255

0 - 255

0 - 255

0 - 255

0 - 255

0 - 255

0 - 5

6 - 255

21

PRELIMINARY

9. 3 DURATION CHANNEL DETAILS

CHANNELSSTORMY C71090STORMY CC C71091


0123456789

101112131415161718192021222324252627282930313233343536373839404142

129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171

43444546474849505152535455565758596061626364656667686970717273747576777879808182838485

172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214

8687888990919293949596979899

100101102103104105106107108109110111112113114115116117118119120121122123124125126127128

215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255

2.505.007.6010.1012.6015.2017.7020.3022.8025.3027.9030.4033.0035.5038.0040.6043.1045.7048.2050.7053.3055.8058.3060.9063.4066.0068.5071.0073.6076.1078.7081.2083.7086.3088.8091.4093.9096.4099.00101.5104.1106.6109.1

330.0332.6335.1337.6340.2342.7345.3347.8350.3352.9355.4358.0360.5363.0365.6368.1370.7373.2375.7378.3380.8383.3385.9388.4391.0393.5396.0398.6401.1403.7406.2408.7411.3413.8416.4418.9421.4424.0426.5429.1431.6434.1436.7

111.7114.2116.7119.3121.8124.4126.9129.4132.0134.5137.1139.6142.1144.7147.2149.8152.3154.8157.4159.9162.5165.0167.5170.1172.6175.1177.7180.2182.8185.3187.8190.4192.9195.5198.0200.5203.1205.6208.2210.7213.2215.8218.3

439.2441.7444.3446.8449.4451.9454.4457.0459.5462.1464.6467.1469.7472.2474.8477.3479.8482.4484.9487.5490.0492.5495.1497.6500.1502.7505.2507.8510.3512.8515.4517.9520.5523.0525.5528.1530.6533.2535.7538.2540.8543.3545.8

220.8223.4225.9228.5231.0233.5236.1238.6241.2243.7246.2248.8251.3253.9256.4258.9261.5264.0266.6269.1271.6274.2276.7279.2281.8284.3286.9289.4291.9294.5297.0299.6302.1304.6307.2309.7312.3314.8317.3319.9322.4325.0327.5

548.4550.9553.5556.0558.5561.1563.6566.2568.7571.2573.8576.3578.9581.4583.9586.5589.0591.6594.1596.6599.2601.7604.2606.8609.3611.9614.4616.9619.5622.0624.6627.1629.6632.2634.7637.3639.8642.3644.9647.4650.0

DMXlevel

DMXlevel

DMXlevel

DMXlevel

DMXlevel

DMXlevel

Time[msec]

Time[msec]

Time[msec]

Time[msec]

Time[msec]

Time[msec]

22

PRELIMINARY

9. 4 RATE CHANNEL DETAILS

CHANNELS

Continued



0123456789

101112131415161718192021222324252627282930313233343536373839404142

000000

0.290.290.430.430.570.570.710.710.860.861.001.001.141.141.321.351.391.431.561.671.721.751.791.852.002.042.082.172.272.332.382.442.502.562.602.662.78

------350035002320232017601760140014001160116010001000880.0880.0760.0740.0720.0700.0640.0600.0580.0570.0560.0540.0500.0490.0480.0460.0440.0430.0420.0410.0400.0390.0384.0376.0360.0

DMXlevel

Frequency[flash/sec]

Time[msec]

43444546474849505152535455565758596061626364656667686970717273747576777879808182838485

8687888990919293949596979899

100101102103104105106107108109110111112113114115116117118119120121122123124125126127128

2.862.983.033.133.173.233.283.333.453.523.573.643.703.793.924.004.084.174.224.274.334.414.464.554.614.674.744.814.885.005.065.135.195.265.335.415.485.565.625.685.755.815.88

5.956.026.106.176.256.336.416.496.586.626.676.716.766.806.856.906.947.047.147.257.357.467.587.697.817.877.948.008.068.138.208.268.338.408.478.558.628.708.778.858.939.019.09

350.0336.0330.0320.0315.0310.0305.0300.0290.0284.0280.0275.0270.0264.0255.0250.0245.0240.0237.0234.0231.0227.0224.0220.0217.0214.0211.0208.0205.0200.0197.5195.0192.5190.0187.5185.0182.5180.0178.0176.0174.0172.0170.0

168.0166.0164.0162.0160.0158.0156.0154.0152.0151.0150.0149.0148.0147.0146.0145.0144.0142.0140.0138.0136.0134.0132.0130.0128.0127.0126.0125.0124.0123.0122.0121.0120.0119.0118.0117.0116.0115.0114.0113.0112.0111.0110.0

DMXlevel

DMXlevel



Time[msec]

Time[msec]

23

PRELIMINARY

9. 4 RATE CHANNEL DETAILS

CHANNELS

STORMY C71090STORMYCC C71091


129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175

9.179.099.139.179.229.269.309.359.399.439.489.529.579.629.719.809.90

10.0010.1010.2010.3110.4210.5310.6410.7510.8710.9911.1111.1711.2411.3011.3611.4311.4911.5611.6311.7011.7611.8311.9011.9812.0512.1212.2012.2712.3512.42

109.0110.0109.5109108.5108.0107.5107.0106.5106.0105.5105.0104.5104.0103.0102.0101.0100.099.098.097.096.095.094.093.092.091.090.089.589.088.588.087.587.086.586.085.585.084.584.083.583.082.582.081.581.080.5

DMXlevel


Time[msec]

176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222

223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255

12.5012.5612.6312.6912.7612.8212.8912.9513.0213.0913.1613.2313.3013.3713.4413.5113.5913.6613.7413.8113.8913.9714.0414.1214.2014.2914.3714.4514.4914.5614.6214.6814.7514.8114.8814.9515.0215.0815.1515.2215.2915.3615.4315.5015.5815.6515.72

15.8015.8715.9516.0316.1016.1816.2616.3416.4216.5016.5816.6716.9517.2417.5417.8618.1818.5218.8719.2319.6120.0020.4120.8321.2821.7422.2222.7323.2623.8124.3925.0025.00

80.079.679.278.878.478.077.677.276.876.476.075.675.274.874.474.073.673.272.872.472.071.671.270.870.470.069.669.269.068.768.468.167.867.567.266.966.666.366.065.765.465.164.864.564.263.963.6

63.363.062.762.462.161.861.561.260.960.660.360.059.058.057.056.055.054.053.052.051.050.049.048.047.046.045.044.043.042.041.040.040.0

DMXlevel

DMXlevel



Time[msec]

Time[msec]

24

PRELIMINARY

10. DURATION time - RATE time (PERIOD) relation

Duration TimeRate Time (Period) Relation

Duration time < Period : FlashingDuration time >= Period : Light continuously ON

time

Period(Rate time)

Duration

Dar

k

Ligh

t

Dar

k

Ligh

t

DutyCycle

[%]

MAX CURRENT vs DUTY CYCLE

2.0

30 100

1.5

MaxCurrent

[A]

1.0

0.5


[A]*

IST00H/002 Rev. PRELIMINARY (07/2014)

stormy stormy cc - clay paky · stormy stormy cc the latest led technology meets the charm of a...

Documents