sleeved couplings / jaw & spider couplings slit couplings · sleeved couplings / jaw &...

1
751 -Set Screw- Sleeved Couplings / Jaw & Spider Couplings K C H Sleeve *4-M F B B t L L 2D L · · Casing (Right Diagram) 3d1H8 4d2H8 CPF *Only 1 set screw location when d1 and d2 are 4mm or less. E Operating Temperature: -20°C ~ 60°C E The lateral, angular, and axial misalignment values shown are for each occurring individually. When multiple misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2. E For the selection criteria and alignment procedures, refer to D P.715. Parts M Material S Surface Treatment A Accessory Casing Zinc Alloy (CPF32: Sintered Alloy) Electrodeposited Coating (Black) (Steam Treatment for CPF32) Set Screw Sleeve Polyurethan (Orange) - Part Number 3 d1, 4 d2 Selection (d1≤d2) L B L t F Sleeve Set Screw 1 Type 2 D C K H M Tightening Torque(N·m) CPF 16 3 4 5 6 6.35 8 27 12 8 3 4 11 14 6/6 M3 0.7 20 5 6 6.35 8 10 34 15 10 4 5 14 18 8/8 25 6 6.35 8 10 12 41 18 12 5 6 17 22 10/10 M4 1.7 32 8 10 12 14 48 21 14 6 7 20 29 12/14 When ordering, select Part Number and Values from Selection Steps 1 ~ 4 . Specify the shaft diameter as d1≤d2. Part Number ( 1 Type· 2 No.) - 3 d1 - 4 d2 CPJLW75 - 19 - 20 5 Q Sleeved Set Screw Order Quantity Standard Service Non-Standard Service Regular Quantity Large Quantity Quantity 1~20 21~ Days to ship Standard To be quoted D 16 3~ 8 20 5~10 25 6~12 32 8~14 LDC (Left Shaft) RDC 5 b t d , d 1 2 Shaft Bore Dia. d1·d2 b t Key Nominal Dim. bxh Reference Dia. Tolerance Reference Dia. Tolerance 10 3 ±0.0125 1.4 +0.1 0 3x3 11·12 4 ±0.0150 1.8 4x4 14~17 5 2.3 5x5 18~22 6 2.8 6x6 24~28 8 ±0.0180 3.3 +0.2 0 8x7 E Operating Temperature: -40°C ~ 100°C E The lateral, angular, and axial misalignment values shown are for each occurring individually. When multiple misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2. E For the selection criteria and alignment procedures, refer to D P.715. Q Jaw & Spider Keyway Dimensions M F L D 3d1H7 L L 4d2H7 (No.=75·90·95) M 2D F L L L 3d1H7 4d2H7 CPJLW With Keywayed Bore d1·d2 (No.=50·70) Parts M Material S Surface Treatment A Accessory Main Body Steel Type Sintered Alloy Set Screw Spider - Part Number 3 d1, 4 d2 Selection (d1≤d2)) D L L F Set Screw 1 Type 2 No. M Tightening Torque (N·m) CPJLW 50 10 11 12 14 15 16 27.3 43.4 15.6 8 M6 5 70 11 12 14 15 16 17 18 19 34.4 50.2 19 75 14 15 16 17 18 19 20 22 44.5 54.1 20.7 7 90 18 19 20 22 24 25 53.6 54.6 20.7 11.2 95 18 19 20 22 24 25 28 53.6 63.8 25.3 M8 10 Alteration Code Spec. Shaft Bore Dia. LDC H8 RDC H8 0.1mm Increment <Ordering Code> LDC7.6 X Not applicable to CPJLW Part Number ( 1 Type· 2 D) - 3 d1 (LDC) - 4 d2 (RDC) CPF25 - LDC7.6 - RDC9.1 D 16 3~8 20 5~10 25 6~12 32 8~14 Express A E P.716. E P.716. Q Characteristic Values Part Number Allowable Torque (N·m) Allowable Angular Misalignment (°) Allowable Lateral Misalignment (mm) Static Torsional Spring Constant (N·m/rad) Max. Rotational Speed (r/min) Moment of Inertia (kg·m 2 ) Mass (g) Type D CPF 16 0.5 2 0.2 4.4 39000 9x10 -7 22 20 1 9.5 31000 2.7x10 -6 42 25 1.5 20 25000 8.1x10 -6 81 32 3 52 19000 2.5x10 -5 150 Features (CPF) coupling with a simple structure. and absorbs torsional vibrations. Part Number Allowable Torque (N·m) Allowable Angular Misalignment (°) Allowable Lateral Misalignment ( mm ) Static Torsional Spring Constant (N·m/rad) Max. Rotational Speed (r/min) Moment of Inertia (kg·m 2 ) Allowable Axial Misalignment (mm) Mass (g) Type No. CPJLW 50 2.1 1 0.38 33.4 18000 1.6x10 -5 + 1.0 0 90 70 3.6 77.7 14000 3.3x10 -5 200 75 8.4 241 11000 1.1x10 -4 + 1.1 0 360 90 9.8 317 9000 2.2x10 -4 520 95 13.1 317 9000 2.6x10 -4 570 Features (CPJLW) bodies and 1 spider. installation, removal and maintenance. (Body and spider are detachable.) CAD Data Folder Name: 14_Couplings 752 CAD Data Folder Name: 14_Couplings [Servo Motor Compatible] -Extra Super Duralumin, Set Screw, Clamping- Slit Couplings 4-M 1 4d 2H8 D L L 3d 1 H8 F F L * Set Screw CPSX E When multiple misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2. E For the selection criteria and alignment procedures, refer to D P.715. * d 1, d2Equal Dia.=d1+0.5 d1, d2Different Diameters = Large Shaft Diameter + 0.5 E For more misalignment tolerances and higher torque capacities, refer to Disc Type on W P.919. Q Features: Due to the use of extra super Duralumin, it has high torsional rigidity and is compatible with servo motors. * F F L 4d 2 D 3d 1 L L G G 4-M 2 Clamping CPCX E CPCX is not available for * marked sizes. Type M Material S Surface Treatment A Accessory CPSX Extra Super Duralumin Clear Anodize Set Screw CPCX Hex Socket Head Cap Screw Part Number 3 d1 4 d2 L L F M1 M2 G 1 Type 2 D Set Screw CPSX Clamping CPCX 16 5 5 6 17.4 6 3 M3 M2 4.74 6 6 19 5 5 6 7 8 20 6.8 3.4 M3 M2.5 5.6 6 6 6.35 7 8 6.35 6.35 8 8 8 * 10 * 10 * 10 24 6 6 8 10 25 8.5 4.25 M4 M3 8 6.35 6.35 8 10 7 8 8 8 9.525 10 9.525 10 10 10 * 11 * 12 * 11 * 12 * 12 * 12 29 8 8 10 11 12 30 10.2 5.1 M4 M3 9 10 10 11 12 * 14 11 12 * 14 12 12 * 14 34 10 14 35 12 6 M5 M3 11 11 14 12 12 14 16 14 14 15 16 15 15 16 16 16 Part Number Allowable Torque (N·m) Allowable Angular Misalignment (°) Lateral Misalignment (mm) Static Torsional Spring Constant (N·m/rad) Max. Rotational Speed (r/min) Moment of Inertia (kg·m 2 ) Allowable Axial Misalignment (mm) Screw Tightening Torque (N·m) Compensation Factor Mass (g) Type D CPSX 16 0.5 0.5 0.05 200 39000 2.8x10 -7 ±0.1 0.7 1 7 19 1 270 33000 6.2x10 -7 10 24 1.5 790 26000 2.0x10 -6 1.7 22 29 2 1400 21000 5.2x10 -6 40 34 3 2200 18000 1.1x10 -5 4 64 CPCX 16 0.5 0.5 0.05 200 39000 2.5x10 -7 ±0.1 0.5 7 19 1 270 33000 5.8x10 -7 1 12 24 1.5 790 26000 1.8x10 -6 1.5 23 29 2 1400 21000 4.7x10 -6 41 34 3 2200 18000 1.1x10 -5 62 When ordering, select Part Number and Values from Selection Steps 1 ~ 4 . Specify the shaft diameter as d1≤d2. Part Number ( 1 Type· 2 D) - 3 d1 - 4 d2 CPSX29 - 12 - 14 Order Quantity Standard Service Non-Standard Service Regular Quantity Large Quantity Quantity 1~20 21~ Days to ship Standard To be quoted 5 Q Characteristic Values Express A

Upload: others

Post on 17-Jul-2020

14 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Sleeved Couplings / Jaw & Spider Couplings Slit Couplings · Sleeved Couplings / Jaw & Spider Couplings K C H Sleeve F *4-M BBt LL 2 D L · · Casing (Right Diagram) 3 d 1 H8 4 d

751

-Set Screw-

Sleeved Couplings / Jaw & Spider Couplings

K

C

H

Sleeve

*4-MFB Bt

L L

2D

L

··

Casing

(Right Diagram)

3d

1H8

4d

2H8

CPF

* Only 1 set screw location when d1 and d2 are 4mm or less.

EOperating Temperature: -20°C ~ 60°C E The lateral, angular, and axial misalignment values shown are

for each occurring individually. When multiple misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2.

EFor the selection criteria and alignment procedures, refer to D P.715.

Parts MMaterial SSurface Treatment AAccessory

Casing Zinc Alloy (CPF32: Sintered Alloy) Electrodeposited Coating (Black) (Steam Treatment for CPF32)Set Screw

Sleeve Polyurethan (Orange) -

Part Number3d1, 4d2 Selection (d1≤d2) L B L t F

Sleeve Set Screw

1Type 2D C K H M Tightening Torque(N·m)

CPF

16 3 4 5 6 6.35 8 27 12 8 3 4 11 14 6/6M3 0.7

20 5 6 6.35 8 10 34 15 10 4 5 14 18 8/825 6 6.35 8 10 12 41 18 12 5 6 17 22 10/10

M4 1.732 8 10 12 14 48 21 14 6 7 20 29 12/14

When ordering, select Part Number and Values from Selection Steps 1~4. Specify the shaft diameter as d1≤d2.

Part Number (1Type·2No.) - 3d1 - 4d2

CPJLW75 - 19 - 20

5

Q Sleeved Set Screw

Order Quantity

Standard Service Non-Standard Service

Regular Quantity Large Quantity

Quantity 1~20 21~Days to ship Standard To be quoted

D16 3~ 820 5~1025 6~1232 8~14

LDC(Left Shaft)

RDC

5

b

t

d , d1 2

Shaft Bore Dia.

d1·d2

b t Key Nominal Dim.

bxhReference Dia. Tolerance Reference Dia. Tolerance

10 3 ±0.0125 1.4+0.1

0

3x311·12 4

±0.01501.8 4x4

14~17 5 2.3 5x518~22 6 2.8 6x624~28 8 ±0.0180 3.3 +0.2

0 8x7

EOperating Temperature: -40°C ~ 100°C E The lateral, angular, and axial misalignment values shown are for each occurring individually. When multiple

misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2.EFor the selection criteria and alignment procedures, refer to D P.715.

QJaw & Spider

Keyway Dimensions

MFL

D

3d

1H7

LL

4d2

H7

(No.=75·90·95)M

2D

FL

LL

3d

1H7

4d2

H7

CPJLW With Keywayed Bore d1·d2

(No.=50·70)

Parts MMaterial SSurface Treatment AAccessory

Main Body Steel Type Sintered AlloySet Screw

Spider -

Part Number3d1, 4d2 Selection (d1≤d2)) D L L F

Set Screw

1Type 2No. M Tightening Torque (N·m)

CPJLW

50 10 11 12 14 15 16 27.3 43.4 15.68

M65

70 11 12 14 15 16 17 18 19 34.4 50.2 1975 14 15 16 17 18 19 20 22 44.5 54.1 20.7

790 18 19 20 22 24 25 53.6 54.6 20.7

11.295 18 19 20 22 24 25 28 53.6 63.8 25.3 M8 10

Alteration Code Spec.

Shaft Bore Dia.

LDC

H8

RDCH

8

0.1mm Increment <Ordering Code> LDC7.6

XNot applicable to CPJLW

Part Number (1Type·2D) - 3d1 (LDC) - 4d2 (RDC)

CPF25 - LDC7.6 - RDC9.1

D16 3~820 5~1025 6~1232 8~14

Express A

E P.716.E P.716.

QCharacteristic Values

Part Number Allowable Torque (N·m)

Allowable

Angular

Misalignment

(°)

Allowable

Lateral

Misalignment

(mm)

Static Torsional

Spring Constant

(N·m/rad)

Max. Rotational

Speed

(r/min)

Moment of Inertia (kg·m2)

Mass (g)Type D

CPF

16 0.5

2 0.2

4.4 39000 9x10-7 2220 1 9.5 31000 2.7x10-6 4225 1.5 20 25000 8.1x10-6 8132 3 52 19000 2.5x10-5 150

Features (CPF)

coupling with a simple structure.

and absorbs torsional vibrations.

Part Number Allowable

Torque

(N·m)

Allowable Angular

Misalignment (°)

Allowable Lateral

Misalignment (mm)

Static Torsional

Spring Constant

(N·m/rad)

Max. Rotational

Speed

(r/min)

Moment of Inertia (kg·m2)

Allowable Axial

Misalignment (mm)

Mass (g)Type No.

CPJLW

50 2.1

1 0.38

33.4 18000 1.6x10-5 + 1.0 0

9070 3.6 77.7 14000 3.3x10-5 20075 8.4 241 11000 1.1x10-4

+ 1.1 0

36090 9.8 317 9000 2.2x10-4 52095 13.1 317 9000 2.6x10-4 570

Features (CPJLW)

bodies and 1 spider.

installation, removal and maintenance.(Body and spider are detachable.)

CAD Data Folder Name: 14_Couplings

752

CAD Data Folder Name: 14_Couplings

[Servo Motor Compatible]-Extra Super Duralumin, Set Screw, Clamping-

Slit Couplings

4-M1

4d

2H8

D

L L

3d

1H8

F F

L

*

Set Screw

CPSX

E When multiple misalignments are occurring simultaneously, the allowable maximum value of each will be reduced to 1/2.

EFor the selection criteria and alignment procedures, refer to D P.715. * d 1, d2Equal Dia.=d1+0.5

d1, d2Different Diameters = Large Shaft Diameter + 0.5

EFor more misalignment tolerances and higher torque capacities, refer to Disc Type on W P.919.QFeatures: Due to the use of extra super Duralumin, it has high torsional rigidity and is compatible with servo motors.

*F F

L

4d

2

D

3d

1

L L

G G

4-M2

Clamping

CPCX

ECPCX is not available for * marked sizes.

Type MMaterial SSurface Treatment AAccessory

CPSX Extra Super Duralumin

Clear Anodize

Set ScrewCPCX Hex Socket Head Cap Screw

Part Number3d1 4d2 L L F M1 M2 G

1Type 2D

Set ScrewCPSX

ClampingCPCX

165 5 6

17.4 6 3 M3 M2 4.746 6

19

5 5 6 7 8

20 6.8 3.4 M3 M2.5 5.66 6 6.35 7 8

6.35 6.35 8

8 8 *10

*10 *10

24

6 6 8 10

25 8.5 4.25 M4 M3 8

6.35 6.35 8 10

7 8

8 8 9.525 10

9.525 10

10 10 *11 *12

*11 *12

*12 *12

29

8 8 10 11 12

30 10.2 5.1 M4 M3 910 10 11 12 *14

11 12 *14

12 12 *14

34

10 14

35 12 6 M5 M3 11

11 14

12 12 14 16

14 14 15 16

15 15 16

16 16

Part Number Allowable Torque (N·m)

Allowable Angular Misalignment

(°)

Lateral Misalignment

(mm)

Static Torsional Spring Constant

(N·m/rad)

Max. Rotational Speed (r/min)

Moment of Inertia (kg·m2)

Allowable Axial Misalignment

(mm)

Screw Tightening Torque (N·m)

Compensation Factor

Mass (g)Type D

CPSX

16 0.5

0.5 0.05

200 39000 2.8x10-7

±0.1

0.7

1

719 1 270 33000 6.2x10-7 1024 1.5 790 26000 2.0x10-6

1.722

29 2 1400 21000 5.2x10-6 4034 3 2200 18000 1.1x10-5 4 64

CPCX

16 0.5

0.5 0.05

200 39000 2.5x10-7

±0.1

0.5 719 1 270 33000 5.8x10-7 1 1224 1.5 790 26000 1.8x10-6

1.523

29 2 1400 21000 4.7x10-6 4134 3 2200 18000 1.1x10-5 62

When ordering, select Part Number and Values from Selection Steps 1~4. Specify the shaft diameter as d1≤d2.

Part Number (1Type·2D) - 3d1 - 4d2

CPSX29 - 12 - 14

Order Quantity

Standard Service Non-Standard Service

Regular Quantity Large Quantity

Quantity 1~20 21~Days to ship Standard To be quoted

5

QCharacteristic Values

Express A