sinumerik 840d sl / sinumerik 828d - siemens · pdf file2 sinumerik 840d sl/sinumerik 828d xml...
TRANSCRIPT
usa.siemens.com/cnc4you
Step-by-step machine registration guide
Protect your investmentSINUMERIK 840D sl / SINUMERIK 828D
2 SINUMERIK 840D sl / SINUMERIK 828D
XML
XML
NCU, Drive
Servomotor
Machine control panel
Enter data into the CNC
Create the XML registration file
USB stick for the file transfer
E-mail file to complete registration
Step-by-step machine registration guide 3
Registering your Siemens CNC-equipped machine tool is quick and easy — and gives you peace-of-mind knowing that support is only a phone call or an e-mail away.
Your warranty period is validated with a start and end date, and a bill of materials is communicated to Siemens so we can provide the best service and support should you require them.
This guide will take you step-by-step through the process. Just follow these easy steps:
Enter the required information into the CNC
n Manufacturer (machine tool builder)
n Machine tool dealer
n End-user
Create the XML registration file
Save the XML registration file to a USB memory stick
E-mail the XML file from your PC to complete the registration
Your SINUMERIK CNC machine tool is now fully registered.
Machine registration step-by-stepIntroduction
4 SINUMERIK 840D sl / SINUMERIK 828D
Depending upon the SINUMERIK CNC and operator panel you’re using, the location of each hard-key
may vary. The location of each soft-key, however, will remain the same. Pictured in the example on
the right: SINUMERIK 840D sl OP12, 12-inch operator panel
Recall This button allows you to go back to the previous screen.
Machine area This button allows you to go to the main (home) screen of SINUMERIK Operate.
Extend key This button allows you to advance to the next page of settings.
Menu Select / Area switchover This button allows you to view the main soft-keys in SINUMERIK Operate.
Operator panel overviewSINUMERIK 840D sl / SINUMERIK 828D
Step-by-step machine registration guide 5
Recall
Machine area
Extend key
Menu Select / Area switchover
Alpha key group
Numerical key group
Cursor key group
Control key group
USB front interface
6 SINUMERIK 840D sl / SINUMERIK 828D
Next, press the Diagnostics — a soft-key found in the bottom of the screen.
Step 2
To begin the machine registration process, you will need to collect some information.
Press the Menu Select. It is a hard-key located on the SINUMERIK operator panel.
Step 1
Step-by-step machine registration guide 7
In the upper-right corner, you will press the Logbook key.
Step 4
In the lower-right corner, you will press the Version key.
Step 3
8 SINUMERIK 840D sl / SINUMERIK 828D
Step 8
Type in the following information as it relates to your machine tool:
n Machine model name, serial number and machine type
Navigate to empty field with cursor keys.
Step 6
Next, press Change, which is also in the upper-right corner of the screen.
Step 5
Step-by-step machine registration guide 9
Press the Dealer key and continue by entering the following information:
n Machine tool dealer
Navigate to empty field with cursor keys
Continue by entering the following information:
n Manufacturer (machine tool builder)
Navigate to empty field with cursor keys
Step 7
10 SINUMERIK 840D sl / SINUMERIK 828D
At any time, press the corresponding soft-key to go back to the Manufacturer, Dealer or End-user screens.
Otherwise, press OK to acknowledge the data you’ve just entered and continue.
Step 10
Press the End user key and continue by entering the following information:
n End-customer
Navigate to empty field with cursor keys
Step 9
Step-by-step machine registration guide 11
Confirm the Logbook entry by pressing OK.
Step 12
Press the Startup complete key.
Step 11
12 SINUMERIK 840D sl / SINUMERIK 828D
The information appearing on this screen should be correct. Please note that the time / time-zone may vary.
Press OK to acknowledge the information you’ve entered and continue.
Step 14
You’re almost finished.
Press the Machine installed key.
Step 13
Step-by-step machine registration guide 13
Now you should see a series of green check marks indicating that everything is okay.
Press the Save key.
Step 16
Next, press the Back key to return to the previous screen and to save your data.
Step 15
14 SINUMERIK 840D sl / SINUMERIK 828D
Enter the following information, when prompted:
n Filename of this registration (required)
n Comment (optional)
Select .XML and then press OK.
This will save your new registration file to the USB stick.
Step 18
Insert a USB stick into the USB port located on the front of the operator panel.
Using the cursor keys, navigate to USB.
Press the OK key.
Step 17
Step-by-step machine registration guide 15
Lastly, remove the USB stick and insert it into your PC.
To complete your machine registration, e-mail the .XML file to:
Step 20
This is the screen you will see as the .XML file is being saved to your USB stick.
Step 19
The information provided in this brochure contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in the terms of contract.
All product designations may be trademarks or product names of Siemens AG or supplier companies whose use by third parties for their own purposes could violate the rights of the owners.
Siemens Industry, Inc. 390 Kent Avenue Elk Grove Village, IL 60007
1-800-879-8079
Order No. MBBR-MRGXX-0815
Printed in USA © 2015 Siemens Industry, Inc.
usa.siemens.com/cnc