PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE

Code: BBD004

Simple Bunk Bed

Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you dol please take a few minutes to read these instructionsl we suggest you carefully unpack everything, lay it out on a clean, flat floor and

identify everything on the parts list in these instructions. Do not throw away any packaging until you are sure you have all the parts.

If you have any problems assembling the product please call our customer services on 01985 300588 and we will try and help. If for any reason you wish to return the product, you must disassemble the product and pack in the original packaging.

Taking care of your product Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is not painted then a superior wood polish can be used - but never use polishes containing silicone. If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then dried with a lint-free cloth. Never clean with abrasives or chemical cleaners. Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture. We know furniture can be heavy but try not to drag furniture across the floor as this can damage it.

Thank you for buying a

PRODUCT SAFETY

piece of furniture

If you have any problems please do contact us for help on e mail customerservices@littlefolksfurniture.co.uk or phone our

CUSTOMER SERVICES 01985 300588

This product is designed to conform to BSEN747:1 2012The MAXIMUM thickness of the UPPER BUNK mattress is 14cm.The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)Periodically check that all assembly fixings are tightened properly, care should be taken to ensure that no fittings are loose.The furniture must be set up on an even and stable surface.Keep away from direct sources of heat, such as electric, gas or coal fires.Do not allow children to climb on the furniture. Using this furniture other than for its intended purpose could cause damage to the structure or serious injury to your child.The Bunk should not be used if any structural part is broken or missing.The upper Bunk is not suitable for children under six years old due to the risk of falls.Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the risk of strangulation.WARNING: Children can become trapped between the bed and the wall. To avoid the risk of serious injury the distance between the top safety barrier and the wall must not exceed 75mm or be more than 230mm.

Fittings

Tools Req

Screwdriver

2 x Allen Key

Parts

22 x Barrel Nuts

8 x Bolts 2.5cm

16 x Bolts 3cm

22 x Large Bolts

6 x sleeve nuts

4 x Double Dowels

68 x Screws 3cm

1 x Screws 1.5cm

8 x Screws 2.5cm

4 x covers

2 x ladder hooks

4 x supports

2 x lower rails

2 x upper rails

ladder

2 x upper ends 2 x lower ends

front safety panel

rear safety panel

2 x mattress base

6 x sleeve nuts

2 x Expanding bolts

Making the bed frames.16 x long Bolts, 16 x Barrel Nuts, an Allen key Push one barrel nut into each mattress rail holes, aligning the slot head to the end hole.Slide each bolt through the bed end holes and into the holes in the end of each mattress rail. Twist the bolts to tighten the bed together.

Align

Tighten

2 x upper ends

2 x lower ends

The holes on the top of the bed legs MUST be on the inside of the bed

The holes on the base of the bed legs MUST be on the inside of the bed

x 2

x 2

Fixing the supportsYou need: 8 x 3cm bolts and an allen keyOrientate the supports with the step sitting on the mattress rails and on the inside of the bed. Now connect each support to the bed using the bolts.

Connecting the rear safety panelYou need: 4 x 3cm bolts, 4 x sleeve nuts, 4 x long bolts and 4 x barrel nutsPlease use two people to complete this assemblyLift the rear safety panel into place, resting in up against the support rails fitted in the prevoius step. Now insert 4 long bolts into the panel end through the bed legs and connecting to 4 x barrel nuts. Now insert the 4 x 3cm bolts through the 4 x holes in the panel with the sleeve nut fitted to the support rail. Tighten both bolt and sleeve nut using two allen keys.Note = you can assemble the safety panel with the barrel nuts facing either inside

or outside of the bed.

x 2

x 2

2 x

2 x

2 x

2 x

Fit the mattress base (upper bed)34 wood screws 3cmNote: Please use TWO people to prevent scratching your bed.Spread the mattress base out to full length on the floor, gently lift the bed base up & over the upper bed frame, lowering down and around the internal vertical support rails. There should be four mattress laths at each end of the bed (between bed end and internal support rails).Screw all the bed laths down EXCEPT the four bed laths positioned at the bed entrance. (we will return to these once the ladder is fitted)Note: Please ensure that the bed lath fitted nearest to the bed end is positioned tight upto the bed end.

Fix the front safety panel4 x 3cm bolts, 2 x sleeve nuts, 2 x long bolts and 2 x barrel nutsChoose the bed entrance (lEFT OR RIGHT)Lift the front safety panel onto the bed with the barrel nut holes (inside of bed) up against the bed leg opposite to the ladder entrance end. Now fit 2 x long bolts through the bed leg and into the barrel nut holes and at the same time connect the panel to the bed entrance support rail using 2 x 3cm and sleeve nuts (sleeve nuts fitted onto the outside face)The remaining support rail (mid positioned) is connected to the safety panel using 2 x 3cm bolts into metal inserts that are fitted to the inside face of the panel.Now tighten all the fittings (front panel and rear panel) as this will strengthen up the bed frame

x 34

Make the bunkYou need: 4 x Double metal dowel and 8 x 2.5cm boltsTWO people to lift upper bed onto the lower bed.Fit 4 x double metal dowels into the top of the lower bed and connect 4 x 2.5cm bolts into the lower metal dowel hole and leave loose.lower the upper bed down onto the 4 metal dowels projecting out of the lower bed. Once both beds are together insert the remaining 4 x bolts into the top metal dowel holes. Some slight wiggling of the lower bolt can sometimes help the top bolt to engage.Once all 8 bolts are connected tighten using the allen key supplied.

Fit the mattress base (Lower bed)34 wood screws (3cm)Note: Please use TWO people to prevent scratching your bed.Spread the mattress base out to full length on the mattress rails and screw every bed lath to the bed supports.Note: Please ensure that the bed lath fitted nearest to the bed end is positioned tight upto the bed end.

x 34

Fix the ladder hooks to the ladderYou need: 4 x 2.5cm wood screws, 2 x ladder hooks and 2 x expanding bolts.Fit both ladder hooks to the ladder by screwing the hooks to the ladder using the pilot holes provided. Note orientation of the hook as shownInsert 2 x expanding bolts into the un-used leg holes at the bed entrance, tigthening both parts to ensure a secure fit.

Fix the ladder to the bed You need: 1 x Small wood screw 1.5cmPlace the ladder into the bed entrance (note that the upper bed laths are not fixed down)The ladder hook should be connected to the mattress side rail using the small wood screw only on the ladder string furthest away from the bed end.You might need to lift the fourth mattress bed lath up in order to fix this ladder screw. Pushing the mattress laths backwards in order to allow the ladder brackets into the gap (It is meant to be a snug fit)Once the ladder is secure screw down the four remaining mattress laths making sure that the last bed lath is tight to the bed ends.

x 2

Conversion

Make two single beds (Convert the bunk)Two people required. Carefully remove the ladder, split the beds, remove the mattress bases and safety panels. Now switch one upper end with a lower end and tighten the bolts. Now fit the mattress bases to the beds.The upper ends can be rotated to hide the double dowel holes, hiding the side holes on the legs from the inside of the bed.Cover the lower bed leg holes that are on the top surface by inserting 4 x covers and fixing them into place using the 4 x 2.5cm screws.