section 5 american ductile iron mechanical joint · pdf fileamerican ductile iron mechanical...

Section 5

AMERICANDuctile IronMechanicalJoint Fittings

5-1

AMERICAN Ductile Iron Mechanical Joint Fittings

AMERICAN supplies a complete line of 4” through 48” mechanical joint fittings meeting the requirements of ANSI/AWWAC110/A21.10 or ANSI/AWWA C153 A21.53, with the joint meeting the require-ments of ANSI/AWWA C111/A21.11. Also included in this section are fittings which are unusual as to size combina-tion, joint combination, outlets, and other variations. These fittings are designated as “AMERICAN standard” and comply with the applicable requirements of the ANSI/AWWA standards. Mechanical joint fittings have been used extensively in underground service with Fastite joint pipe as well as mechanicaljoint pipe. Since 48” is the maximum size mechanical joint, Fastite or Lok-Ring fittings are normally furnished with AMERICAN 54” and larger Fastite or Lok-Ring joint pipe. While mechanical joint fittings have provided excellent service for decades, their use is currently being supplanted in many cases by Fastite, Flex-Ring, and Lok-Ring fittings. These fittings offer improved and less labor-intensive field assembly and per-formance, and their use should be consid-ered in lieu of mechanical joint fittings in

most large-diameter applications. See Section 4. When joint restraint is required under-ground or aboveground, several types of re-strained joints are available from AMERICAN. See Sections 4 and 9. The design of mechanical joint fittingsis based on their use with pipe having out-side diameters that are standard for me-chanical joint and for Fastite joint pipe. In planning a mechanical joint connection to an old existing pipeline, the outside diam-eter should be carefully checked where con-nection is to be made. Mechanical joint fittings are normally furnished complete with a gland, plain rub-ber gasket, and tee head alloy steel bolts with heavy hex nuts for each socket. Ductile iron fittings for pressure ratings of 150, 250 and 350 psi are furnished as shown in the tables in this Section. Fittings for water service are generally furnished with cement lining in accordance with AWWA C104 and with an outside as-phaltic coating. They can also be furnished asphaltic coated or uncoated inside. For special conditions, other types of coatings and linings are available. See Section 11.

The principal standards covering full body mechanical joint fittings are ANSI/AWWA C110/A21.10 and ANSI/AWWA C111/A21.11. Compact ductile iron fittings are covered in ANSI/AWWAC153/A21.53. These and other standards are referenced throughout this section either by the fullANSI/AWWA designation or by only the AWWA numbering, such as AWWA C110.

Installing a mechanical joint bend in a gravity sewer utilizing field-cut closure piecesto locate the fitting accurately.

5-2

1. Fittings in the following tables with ANSI/AWWA standards listed in the head-ing are as specified in those standards. Fit-tings in tables with heading “AMERICAN standard” are either not included in the ANSI/AWWA standards or vary therefrom in weights and/or dimensions. 2. Fittings are manufactured of ductile iron meeting the requirements of AWWA C110 or C153, as applicable. 3. Weights of accessories are not in-cluded in weights of fittings shown in ta-bles unless specifically noted. Where “As-sembled Weight” is shown, joint materials are shipped assembled on the fitting. For weights of accessories, see Section 2. 4. Weights and dimensions of fittingscan vary due to changes in foundry equip-ment. 5. Orientation of bolt holes in me-chanical joint fittings with respect to any centerline* is not fixed. Where bolt holes are required to straddle the centerline of the fitting, this must be specified by the purchaser. 6. For allowable joint deflection of mechanical joints, see Section 2. 7. Mechanical joint flanges can nor-mally be furnished tapped for studs when specified by the purchaser. See Section 2, Table No. 2-15. 8. All pressure ratings shown are for water service. 9. The ANSI/AWWA C110/A21.10 thicknesses of most mechanical joint fit-tings shown in tables in this section are the same thicknesses as Class “B” or “D” (most of them being Class “B”) per the obsolete AWWA C100 standard; these thicknesses and corresponding outside di-ameters are shown in Section 12, Table No. 12-1. 10. Some fittings are available with body metal thickness other than as shown in the tables. Some fittings are available in different sizes and with different size com-binations than shown. Check AMERICAN regarding special requirements. 11. See Section 7 for AMERICAN specials. 12. Locations of taps in mechani-cal joint fittings should be designated as shown on page 6-5 for flanged fittings.

13. MJ connecting pieces (MJ-MJ, MJ-PE, MJ-Flg, and Flg-PE) are furnished by AMERICAN as fabricated piping and can be furnished in variable lengths. See Sections 7 and 8. 14. Fittings may be furnished by AMERICAN manufactured by others. Any such fittings will be manufactured in ac-cordance with appropriate ANSI/AWWA or AMERICAN standards. 15. Some configurations shown for both AWWA C110 and C153 may not be available both ways. 16. The thicknesses shown for C153 standard fittings are the nominal thick-nesses shown in this standard. The shown lengths and center-to-socket dimensions of these fittings are minimum dimensions also in accordance with the C153 stan-dard. Actual thicknesses of fittings will vary as allowed by the standard, and actual lengths and center-to-socket dimensions will generally be equal to or greater than those shown in the tables, all depending on foundry equipment. 17. AMERICAN manufactures 4” through 12” Mechanical Joint Ductile Iron pipe in accordance with AWWA C151 and AWWA C111 and Mechanical Joint fit-tings up through 48” in accordance with AWWA C153, AWWA C110, and AWWA C111, as described therein. However, AMERICAN does not warrant the perfor-mance of third-party mechanical retainer glands or joints using third-party retainer glands, since the design, manufacturing, and installation methods are beyond our control. AMERICAN does manufacture a number of restrained joints such as Fast-Grip®, Flex-Ring®, Field Flex-Ring®, Lok-Ring®, Flex-Lok®, and other devices, where we warrant the joint as well as the associ-ated pipe and fittings of our manufacture.

*The normal but not universal practice is to have the bolt holes straddle the vertical centerline of a fitting, which is determined when the fitting is in the position to change the direction of fluid flowing in a horizontal plane. With standard base bends and standard base tees, the determi-nation is made when the fitting is in position to change the direction of fluid flowing in a vertical plane.

General Notes Relating to Mechanical Joints

5-3

AMERICAN Ductile Iron Mechanical Joint FittingsApplications of Standard Fittings

Inmanycasesspecialfittingsforvariousconditionsarerequired;someoftheseareshownaboveincolumnsheaded“FormerlyRequired.”Underthecolumnsheaded“PreferredAlternate”areshowncombinationsofstandardfittingswhichinsomesituationswillprovidethedesiredconnection.Foreconomyandavailability,itisoftenadvantageoustousethestandardfittings.

5-4


ANSI/AWWA C110 and C153Mechanical Joint Dimensions

Table No. 5-1

Sizein. A

Plain End

Bolts

B J K1 K2 C110 C153

LM S No. per

JointSizein.

Dimensions in Inches

14 14.80 2.50 17.50 19.38 19.12 1.00 1.60 1.75 1.65 14 13/4x31/2 16 16.90 2.50 19.50 11.31 11.12 1.06 1.63 1.88 1.70 16 13/4x31/2 18 19.05 2.50 11.75 13.63 13.37 1.12 1.66 1.00 1.75 16 13/4 x 4 10 11.10 2.50 14.00 15.81 15.62 1.19 1.70 1.00 1.80 18 13/4 x 4 12 13.20 2.50 16.25 18.06 18.00 1.251 1.73 1.00 1.85 18 13/4 x 4 14 15.30 3.50 18.75 20.69 20.25 1.311 1.79 1.25 1.89 10 13/4 x 41/2 16 17.40 3.50 21.00 22.94 22.50 1.38 1.85 1.31 1.97 12 13/4 x 41/2 18 19.50 3.50 23.25 25.28 24.75 1.44 1.00 1.38 1.05 12 13/4 x 41/2 20 21.60 3.50 25.50 27.08 27.00 1.50 1.02 1.44 1.12 14 13/4 x 41/2 24 25.80 3.50 30.00 31.75 31.50 1.62 1.02 1.56 1.22 16 13/4x5 30 32.00 4.00 36.88 39.12 39.12 1.81 – 2.00 1.50 20 11x6 36 38.30 4.00 43.75 46.00 46.00 2.00 – 2.00 1.80 24 11x6 42 44.50 4.00 50.62 53.12 53.12 2.00 – 2.00 1.95 28 11/4x61/2 48 50.80 4.00 57.50 60.00 60.00 2.00 – 2.00 2.20 32 11/4x61/2

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.FormechanicaljointsforpipeseeSection2.FortolerancesandadditionaldimensionsseeAWWAC111.Boltholesare1/8”largerthantheboltdiameters.MechanicalJointRetainerGlanddesigns(byothers)oftenrequirelongerthantheabovestandardbolting.SeeSections9and12regardingalternativerestrainedjoints,andalsoretainerglandapplications.

5-5


ANSI/AWWA C110/A21.10Mechanical Joint Plain End

Standard Dimensions

Table No. 5-2

Sizein.

DimensionsinInches

TA L

Weightof(8”long)PlainEnd

lb

14 14.80 1.47 5.5 113 16 16.90 1.50 5.5 121 18 19.05 1.54 5.5 130 10 11.10 1.60 5.5 141 12 13.20 1.68 5.5 156 14 15.30 1.66 8.0 163 16 17.40 1.70 8.0 176 18 19.50 1.75 8.0 192 20 21.60 1.80 8.0 109 24 25.80 1.89 8.0 145 30 32.00 1.03 8.0 208 36 38.30 1.15 8.0 279 42 44.50 1.28 8.0 362 48 50.80 1.42 8.0 458

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.The“L”dimensionisminimumlengthoftheplainendwhichmustbegaugedtoensuretheoutsidediameteriswithinthedimensionsandtolerancesrequired.ThelayinglengthofaplainendofanMJfittingis8”longerthanthelayinglengthofabellend.PlainendsoffittingsmaybefurnishedwithbeveledendsforassemblywitheitherFastiteormechanicaljoints.However,ifbeveledendsarerequiredtheymustbespecified.

5-6


ANSI/AWWA C110/A21.10 and C153/A21.5390° Bends (1/4th)

Table No. 5-3 AWWA C110

Table No. 5-4 AWWA C153 - Compact

Sizein.

Sizein.

PressureRating

psi

PressureRating

psi

T A S R

T nom.

A min.

S min.

MJ & MJ MJ & PE

MJ & MJ MJ & PE



Weight in Pounds

Weight in Pounds

14 350 1.52 16.5 14.5 14.5 1155 1150 16 350 1.55 18.0 16.0 16.0 1185 1180 18 350 1.60 19.0 17.0 17.0 1125 1120 10 350 1.68 11.0 19.0 19.0 1190 1190 12 350 1.75 12.0 20.0 10.0 1255 1255 14 350 1.66 14.0 22.0 11.5 1340 1325 16 350 1.70 15.0 23.0 12.5 1430 1410 18 350 1.75 16.5 24.5 14.0 1545 1520 20 350 1.80 18.0 26.0 15.5 1680 1650 24 350 1.89 22.0 30.0 18.5 1025 1985 30 250 1.03 25.0 33.0 21.5 1690 1585 36 250 1.15 28.0 36.0 24.5 2475 2310 42 250 1.28 31.0 39.0 27.5 3410 3200 48 250 1.42 34.0 42.0 30.5 4595 4330

14 350 .34 14.00 9.50 1125 1122 16 350 .36 15.00 11.50 1139 1141 18 350 .38 16.50 12.50 1157 1158 10 350 .40 17.50 13.00 1189 1 83 12 350 .42 19.00 14.50 1108 1114 14 350 .47 11.50 19.50 1210 1197 16 350 .50 12.50 20.50 1264 1248 18 350 .54 14.00 21.00 1335 1325 20 350 .57 15.00 22.50 1400 1390 24 350 .61 16.75 25.00 1565 1575 30 250* .66 21.50 30.50 930 1865 36 250* .74 24.50 33.50 1450 1355 42 250* .82 29.25 38.25 2205 2055 48 250* .90 33.25 42.25 2990 2805

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsmeettheC153standardminimumdimension.

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.*BasedonperformancetestingperAWWAC153,AMERICANcanratethesefittings350psi.However,becauseofthemorelabor–intensiveandlabor–reliantassemblyoftheMJjointandthesubstantialthrustrestraintrequirementsforworkingpressuresthathigh,werecommendpush–onjointconfigurations(Fastite,Flex–RingandLok–Ring)forhighpressureapplications.

5-7


ANSI/AWWA C110/A21.10 and C153/A21.5345° Bends (1/8th)



Sizein.

Sizein.

PressureRating

psi

PressureRating

psi

T A S R

T nom.

A min.

S min.

MJ & MJ MJ & PE

MJ & MJ MJ & PE



Weight in Pounds

Weight in Pounds

14 350 1.52 14.0 12.0 14.81 1150 1v45 16 350 1.55 15.0 13.0 17.25 1175 1170 18 350 1.60 15.5 13.5 18.44 1110 1105 10 350 1.68 16.5 14.5 10.88 1155 1155 12 350 1.75 17.5 15.5 13.25 1215 1215 14 350 1.66 17.5 15.5 12.06 1270 1255 16 350 1.70 18.0 16.0 13.25 1340 1320 18 350 1.75 18.5 16.5 14.50 1420 1395 20 350 1.80 19.5 17.5 16.88 1530 1500 24 350 1.89 11.0 19.0 18.12 1755 1715 30 250 1.03 15.0 23.0 27.75 1380 1275 36 250 1.15 18.0 26.0 35.00 2095 1930 42 250 1.28 21.0 29.0 42.25 2955 2745 48 250 1.42 24.0 32.0 49.50 4080 3815

14 350 .34 12.0 17.5 1122 1119 16 350 .36 13.0 18.5 1132 1134 18 350 .38 13.5 19.0 1146 1149 10 350 .40 14.5 10.0 1170 1169 12 350 .42 15.5 11.0 1 86 1 93 14 350 .47 15.0 13.0 1160 1146 16 350 .50 15.5 13.5 1202 1184 18 350 .54 16.0 13.0 1250 1235 20 350 .57 17.0 14.0 1305 1290 24 350 .61 17.5 14.5 1405 1390 30 250* .66 10.5 19.5 1780 1715 36 250* .74 11.5 21.0 1135 1040 42 250* .82 14.0 23.0 1610 1460 48 250* .90 15.0 24.0 2090 1905



5-8


ANSI/AWWA C110/A21.10 and C153/A21.53221⁄2° Bends (1/16th)



Sizein.

Sizein.

PressureRating

psi

PressureRating

psi

T A S R

T nom.

A min.

S min.

MJ & MJ MJ & PE

MJ & MJ MJ & PE



Weight in Pounds

Weight in Pounds

14 350 1.34 11.5 17.0 1118 1v18 16 350 1.36 12.0 17.5 1131 1129 18 350 1.38 12.5 18.0 1146 1143 10 350 1.40 13.0 18.5 1164 1161 12 350 1.42 13.5 19.0 1180 1179 14 350 1.47 13.75 11.25 1136 1133 16 350 1.50 13.75 11.75 1172 1166 18 350 1.54 14.5 13.0 1255 1235 20 350 1.57 14.5 14.0 1310 1300 24 350 1.61 14.5 14.5 1412 1395 30 250* 1.66 16.75 15.75 1665 1600 36 250* 1.74 17.75 16.75 1960 1865 42 250* 1.82 19.0 18.0 1350 1200 48 250* 1.90 10.0 19.0 1760 1575

4 350 .52 4.0 12.0 10.06 50 45 6 350 .55 5.0 13.0 15.06 75 70 8 350 .60 5.5 13.5 17.62 110 105 10 350 .68 6.5 14.5 22.62 160 160 12 350 .75 7.5 15.5 27.62 220 220 14 350 .66 7.5 15.5 25.12 275 – 16 350 .70 8.0 16.0 27.62 345 325 18 350 .75 8.5 16.5 30.19 430 405 20 350 .80 9.5 17.5 35.19 535 505 24 350 .89 11.0 19.0 37.69 765 725 30 250 1.03 15.0 23.0 57.81 1400 1295 36 250 1.15 18.0 26.0 72.88 2135 1970 42 250 1.28 21.0 29.0 88.00 3020 2810 48 250 1.42 24.0 32.0 103.06 4170 –



5-9


ANSI/AWWA C110/A21.10 and C153/A21.53111⁄4° Bends (1/32nd)



Sizein.

Sizein.

PressureRating

psi

PressureRating

psi

T A S R

T nom.

A min.

S min.

MJ & MJ MJ & PE

MJ & MJ MJ & PE



Weight in Pounds

Weight in Pounds

14 350 1.52 14.0 12.0 120.31 1150 1145 16 350 1.55 15.0 13.0 130.50 1175 1170 18 350 1.60 15.5 13.5 135.50 1110 1105 10 350 1.68 16.5 14.5 145.69 1160 1160 12 350 1.75 17.5 15.5 155.81 1220 1220 14 350 1.66 17.5 15.5 150.75 1275 1260 16 350 1.70 18.0 16.0 155.81 1345 1325 18 350 1.75 18.5 16.5 160.94 1430 1405 20 350 1.80 19.5 17.5 171.06 1540 1510 24 350 1.89 11.0 19.0 176.12 1770 1730 30 250 1.03 15.0 23.0 116.75 1410 1305 36 250 1.15 18.0 26.0 147.25 2145 1980 42 250 1.28 21.0 29.0 177.69 3035 – 48 250 1.42 24.0 32.0 208.12 4190 3925

14 350 .34 1.25 16.25 1116 1117 16 350 .36 1.5 17.0 1130 1127 18 350 .38 1.75 17.25 1142 1139 10 350 .40 2.0 17.5 1158 1152 12 350 .42 2.25 17.75 1167 1169 14 350 .47 2.5 10.5 1 93 1118 16 350 .50 2.5 10.5 1148 1136 18 350 .54 3.0 13.0 1205 1235 20 350 .57 3.0 14.0 1245 1300 24 350 .61 3.0 14.5 1315 1400 30 250* .66 4.75 13.75 1600 1535 36 250* .74 5.0 14.0 1820 1725 42 250* .82 6.0 15.0 1180 1030 48 250* .90 6.5 15.5 1475 1290


Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.*BasedonperformancetestingperAWWAC153,AMERICANcanratethesefittings350psi.However,becauseofthemorelabor–intensiveandlabor–reliantassemblyoftheMJjointandthesubstantialthrustrestraintrequirementsforworkingpressuresthathigh,werecommendpush–onjointconfigurations(Fastite,Flex–RingandLok–Ring)forhighpressureapplications.SeeGeneralNotesonpage5–2.

5-10


ANSI/AWWA C110/A21.10Tees and Crosses


Table No. 5-11

Sizein.

Run Branch

PressureRating

psiT T1 H J S

Weight in Pounds

Tee Cross

All MJ


14 14 350 .52 .52 16.5 16.5 14.5 180 105 16 14 350 .55 .52 18.0 18.0 16.0 115 140 16 16 350 .55 .55 18.0 18.0 16.0 125 160 18 14 350 .60 .52 19.0 19.0 17.0 165 185 18 16 350 .60 .55 19.0 19.0 17.0 175 205 18 18 350 .60 .60 19.0 19.0 17.0 185 235 10 14 350 .68 .52 11.0 11.0 19.0 235 260 10 16 350 .68 .55 11.0 11.0 19.0 250 285 10 18 350 .68 .60 11.0 11.0 19.0 260 310 10 10 350 .80 .80 11.0 11.0 19.0 310 380 12 14 350 .75 .52 12.0 12.0 20.0 315 340 12 16 350 .75 .55 12.0 12.0 20.0 325 360 12 18 350 .75 .60 12.0 12.0 20.0 340 385 12 10 350 .87 .80 12.0 12.0 20.0 390 460 12 12 350 .87 .87 12.0 12.0 20.0 410 495

All MJ



5-11

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.

Table No. 5-11—Continued

Sizein.

Run Branch

PressureRating

psiT T1 H J S

Weight in Pounds

Tee Cross

All MJ All MJ


*14 14 350 1.66 .52 14.0 14.0 22.0 1420 450 14 16 350 1.66 .55 14.0 14.0 22.0 1435 475 14 18 350 1.66 .60 14.0 14.0 22.0 1450 500 14 10 350 1.66 .68 14.0 14.0 22.0 1465 540 14 12 350 1.66 .75 14.0 14.0 22.0 1495 585 14 14 350 1.66 .66 14.0 14.0 22.0 1520 635*16 14 350 1.70 .52 15.0 15.0 23.0 1525 555 16 16 350 1.70 .55 15.0 15.0 23.0 1540 575 16 18 350 1.70 .60 15.0 15.0 23.0 1550 605 16 10 350 1.70 .68 15.0 15.0 23.0 1570 645 16 12 350 1.70 .75 15.0 15.0 23.0 1590 685 16 14 350 1.70 .66 15.0 15.0 23.0 1620 735 16 16 350 1.70 .70 15.0 15.0 23.0 1650 790 18 16 350 1.75 .55 13.0 15.5 21.0 1590 625 18 18 350 1.75 .60 13.0 15.5 21.0 1605 655 18 10 350 1.75 .68 13.0 15.5 21.0 1620 685 18 12 350 1.75 .75 13.0 15.5 21.0 1640 725 18 14 350 1.75 .66 16.5 16.5 24.5 1755 870 18 16 350 1.75 .70 16.5 16.5 24.5 1785 930 18 18 350 1.75 .75 16.5 16.5 24.5 1820 995 20 16 350 1.80 .55 14.0 17.0 22.0 1725 760 20 18 350 1.80 .60 14.0 17.0 22.0 1735 790 20 10 350 1.80 .68 14.0 17.0 22.0 1755 820 20 12 350 1.80 .75 14.0 17.0 22.0 1775 860 20 14 350 1.80 .66 14.0 17.0 22.0 1795 905 20 16 350 1.80 .70 18.0 18.0 26.0 19451085 20 18 350 1.80 .75 18.0 18.0 26.0 1985 1155 20 20 350 1.80 .80 18.0 18.0 26.0 1020 1230 24 16 350 1.89 .55 15.0 19.0 23.0 1985 1025 24 18 350 1.89 .60 15.0 19.0 23.0 1000 1045 24 10 350 1.89 .68 15.0 19.0 23.0 1020 1085 24 12 350 1.89 .75 15.0 19.0 23.0 1030 1110 24 14 350 1.89 .66 15.0 19.0 23.0 1055 1155 24 16 350 1.89 .70 15.0 19.0 23.0 1075 1200 24 18 350 1.89 .75 22.0 22.0 30.0 1400 1590 24 20 350 1.89 .80 22.0 22.0 30.0 1450 1675 24 24 350 1.89 .89 22.0 22.0 30.0 1535 1835 30 16 250 1.03 .55 18.0 23.0 26.0 1730 1770 30 18 250 1.03 .60 18.0 23.0 26.0 1745 1795 30 10 250 1.03 .68 18.0 23.0 26.0 1760 1830 30 12 250 1.03 .75 18.0 23.0 26.0 1780 1865 30 14 250 1.03 .66 18.0 23.0 26.0 1800 1905 30 16 250 1.03 .70 18.0 23.0 26.0 1820 1950 30 18 250 1.03 .75 18.0 23.0 26.0 1845 2000 30 20 250 1.03 .80 18.0 23.0 26.0 1875 2060 30 24 250 1.03 .89 25.0 25.0 33.0 2400 2675 30 30 250 1.031.03 25.0 25.0 33.0 2595 3075

5-12




Sizein.

Run Branch

PressureRating

psiT T1 H J S

Weight in Pounds

Tee Cross

All MJ All MJ


36 12 250 1.15 1.75 20.0 26.0 28.0 2550 2630 36 14 250 1.15 1.66 20.0 26.0 28.0 2570 2665 36 16 250 1.15 1.70 20.0 26.0 28.0 2585 2705 36 18 250 1.15 1.75 20.0 26.0 28.0 2610 2750 36 20 250 1.15 1.80 20.0 26.0 28.0 2635 2805 36 24 250 1.15 1.89 20.0 26.0 28.0 2690 2910 36 30 250 1.15 1.03 28.0 28.0 36.0 3545 3965 36 36 250 1.15 1.15 28.0 28.0 36.0 3745 4370 42 24 250 1.28 1.89 23.0 30.0 31.0 3690 3910 42 30 250 1.28 1.03 31.0 31.0 39.0 4650 5040 42 36 250 1.78 1.58 31.0 31.0 39.0 6075 6655 42 42 250 1.78 1.78 31.0 31.0 39.0 6320 7145 48 24 250 1.42 1.89 26.0 34.0 34.0 4995 5210 48 30 250 1.42 1.03 26.0 34.0 34.0 5140 5495 48 36 250 1.42 1.15 34.0 34.0 42.0 6280 6790 48 42 250 1.96 1.78 34.0 34.0 42.0 8130 8815 48 48 250 1.96 1.96 34.0 34.0 42.0 8420 9380

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsmeettheC153standardminimumdimension.Note:Welded–onoutletsmaybepreferabletoteesandcrossesinmanycasesfromalayout,installationandeconomicalstandpoint.SeeSection7.

5-13

AMERICAN Ductile Iron Mechanical Joint FittingsANSI/AWWA C153/A21.53Compact Tees and Crosses

Table No. 5-12

Sizein.

Run Branch

PressureRating

psi T nom.

T1nom.

H min.

Jmin.

Weight in Pounds

Tee Cross

All MJ All MJ


14 14 350 .34 .34 14.0 14.0 132 40 16 14 350 .36 .34 14.0 15.0 146 681 6 16 350 .36 .36 15.0 15.0 156 175 18 14 350 .38 .34 14.0 16.5 160 99 18 16 350 .38 .36 15.0 16.5 172 108 18 18 350 .38 .38 16.5 16.5 186 105 10 14 350 .40 .34 14.0 17.5 178 98 10 16 350 .40 .36 15.0 17.5 190 11810 18 350 .40 .38 16.5 17.5 105 138 10 10 350 .40 .40 17.5 17.5 120 145 12 14 350 .42 .34 14.0 18.75 194 10012 16 350 .42 .36 15.0 18.75 110 140 12 18 350 .42 .38 16.5 18.75 125 162 12 10 350 .42 .40 17.5 18.75 140 190 12 12 350 .42 .42 18.75 18.75 160 213 14 14 350 .47 .34 15.5 10.5 172 162 14 16 350 .47 .36 16.5 10.5 182 181 14 18 350 .47 .38 17.5 10.5 206 259 14 10 350 .47 .40 18.5 10.5 228 223 14 12 350 .47 .42 19.5 10.5 234 244 14 14 350 .47 .47 10.5 10.5 280 299 16 16 350 .50 .36 16.5 11.5 228 250 16 18 350 .50 .38 17.5 11.5 248 289 16 10 350 .50 .40 18.5 11.5 264 345 16 12 350 .50 .42 19.5 11.5 280 397 16 14 350 .50 .47 10.5 11.5 316 333 16 16 350 .50 .50 11.5 11.5 322 385

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.Numeralsoncutsindicatestandardorderofspecifyingsizeandjointtypeoffitting.SeeSection6forreducingtees,teesreducingonrunandbranch,andbullheadtees.

5-14

AMERICAN Ductile Iron Mechanical Joint FittingsANSI/AWWA C153/A21.53Compact Tees and Crosses


Sizein.

Run Branch

PressureRating

psi T nom.

T1nom.

H min.

Jmin.

Weight in Pounds

Tee Cross

All MJ All MJ


18 16 350 .54 .36 16.5 12.5 1275 260 18 18 350 .54 .38 17.5 12.5 1295 282 18 10 350 .54 .40 18.5 12.5 1315 308 18 12 350 .54 .42 19.5 12.5 1335 – 18 14 350 .54 .47 10.5 12.5 1380 384 18 16 350 .54 .50 11.5 12.5 1405 – 18 18 350 .54 .54 12.5 12.5 1435 630 20 16 350 .57 .36 16.5 14.0 1315 306 20 18 350 .57 .38 18.0 14.0 1345 341 20 10 350 .57 .40 19.0 14.0 1370 370 20 12 350 .57 .42 10.0 14.0 1395 392 20 14 350 .57 .47 11.0 14.0 1440 451 20 16 350 .57 .50 12.0 14.0 1465 634 20 18 350 .57 .54 13.0 14.0 1505 547 20 20 350 .57 .57 14.0 14.0 1535 605 24 16 350 .61 .36 13.0 17.0 1415 1403 24 18 350 .61 .38 13.0 17.0 1445 1431 24 10 350 .61 .40 13.0 17.0 1470 1465 24 12 350 .61 .42 13.0 17.0 1500 1494 24 14 350 .61 .47 13.0 17.0 1550 1553 24 16 350 .61 .50 13.0 17.0 1580 1714 24 18 350 .61 .54 17.0 17.0 1625 1 – 24 20 350 .61 .57 17.0 17.0 1660 1809 24 24 350 .61 .61 17.0 17.0 1720 830 30 20 250* .66 .57 16.5 21.0 995 991 30 24 250* .66 .61 22.0 22.0 1060 1083 30 30 250* .66 .66 22.0 22.0 1323 1840 36 24 250* .74 .61 18.5 26.0 1498 – 36 30 250* .74 .66 26.0 26.0 1555 – 36 36 250* .74 .74 26.0 26.0 1900 2655 42 24 250* .82 .61 22.0 27.5 2270 2055 42 30 250* .82 .66 22.0 29.5 2425 2950 42 36 250* .82 .74 30.0 30.0 3000 3955 42 42 250* .82 .82 30.0 30.0 3175 3725 48 24 250* .90 .61 23.0 32.0 2870 2766 48 30 250* .90 .66 23.0 32.0 3050 4500 48 36 250* .90 .74 33.5 32.25 3900 3719 48 42 250* .90 .82 33.5 33.5 4100 4590 48 48 250* .90 .90 33.5 33.5 4250 4955

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.SeeGeneralNotesonpage5–2.*BasedonperformancetestingperAWWA C153, AMERICANcanratethesefittings350psi.However,becauseofthemorelabor–intensiveandlabor–reliantassemblyoftheMJjointandthesubstantialthrustrestraintrequirementsforworkingpressuresthathigh,werecommendpush–onjointconfigurations(Fastite,Flex–RingandLok–Ring)forhigh–pressureapplications.

LargeEnd

SmallEnd

5-15


ANSI/AWWA C110/A21.10Reducers

Table No. 5-13

T Large End

T1 Small End

L in

Weight lb.

L in

Weight lb.

Thicknessin. MJ & MJ Large End MJ

16 14 350 .55 .52 19 160 17 160 18 14 350 .60 .52 11 180 19 180 18 16 350 .60 .55 11 195 19 190 10 14 350 .68 .52 12 105 20 100 10 16 350 .68 .55 12 115 20 115 10 18 350 .68 .60 12 135 20 130 12 14 350 .75 .52 14 135 22 130 12 16 350 .75 .55 14 150 22 145 12 18 350 .75 .60 14 165 22 165 12 10 350 .75 .68 14 190 22 185 14 16 350 .66 .55 16 190 24 185 14 18 350 .66 .60 16 210 24 205 14 10 350 .66 .68 16 230 – – 14 12 350 .66 .75 16 255 24 255 16 16 350 .70 .55 18 230 26 230 16 18 350 .70 .60 18 250 26 250 16 10 350 .70 .68 18 280 26 275 16 12 350 .70 .75 18 305 26 305 16 14 350 .70 .66 18 335 26 315 18 18 350 .75 .60 19 295 27 295 18 10 350 .75 .68 19 325 27 320 18 12 350 .75 .75 19 350 27 350 18 14 350 .75 .66 19 380 27 365 18 16 350 .75 .70 19 415 27 395

Sizein. Pressure

Ratingpsi


LargeEnd

SmallEnd

5-16


ANSI/AWWA C110/A21.10Reducers


T Large End

T1 Small End

L in.

Weight lb

L in.

Weight lb


**20 16 350 1.80 1.55 20 1320 – 1 – **20 18 350 1.80 1.60 20 1360 – 1 – 20 10 350 1.80 1.68 20 1375 28 1375 20 12 350 1.80 1.75 20 1405 28 1405 20 14 350 1.80 1.66 20 1430 28 1415 20 16 350 1.80 1.70 20 1470 28 1445 20 18 350 1.80 1.75 20 1510 28 1485 **24 18 350 1.89 1.60 24 1475 – 1 – **24 10 350 1.89 1.68 24 1510 – 1 – 24 12 350 1.89 1.75 24 1550 32 1550 24 14 350 1.89 1.66 24 1575 32 1560 24 16 350 1.89 1.70 24 1615 32 1595 24 18 350 1.89 1.75 24 1660 32 1635 24 20 350 1.89 1.80 24 1705 32 1675**30 12 250 1.03 1.75 30 1865 38 1875 **30 16 250 1.03 1.70 30 1940 38 1920 30 18 250 1.03 1.75 30 1990 38 965 30 20 250 1.03 1.80 30 1050 38 1020 30 24 250 1.03 1.89 30 1165 38 1125**36 14 250 1.15 1.66 36 1265 – – **36 16 250 1.15 1.70 36 1320 – – **36 18 250 1.15 1.75 36 1385 – – 36 20 250 1.15 1.80 36 1450 44 1420 36 24 250 1.15 1.89 36 1580 44 1535 36 30 250 1.15 1.03 36 1855 44 1750 42 20 250 1.28 1.80 42 1915 – – 42 24 250 1.28 1.89 42 2060 – – 42 30 250 1.28 1.03 42 2370 50 2265 42 36 250 1.28 1.15 42 2695 50 2530 48 30 250 1.42 1.03 48 3005 – – 48 36 250 1.42 1.15 48 3370 – – 48 42 250 1.42 1.28 48 3750 56 3540

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsmeettheC153standardminimumdimension.**NotincludedinAWWAC110.Eccentricreducersareavailableinsomeoftheabovesizes;dimensionsandweightsareapproximatelythesameasthoseshownforconcentricreducers.Checkavailabilityofspecifiedsizeofeccentricreducersasrequired.

Sizein. Pressure

Ratingpsi

LargeEnd

SmallEnd

5-17



ANSI/AWWA C153/A21.53Compact Reducers

Table No. 5-14

T Large End

(nom)

T1 Small End

(nom)

L in.

(min)

Weight lb

L in.

(min)

Weight lb


16 14 350 .36 .34 4 132 19.5 122 1 18 14 350 .38 .34 5 143 10.5 129 18 16 350 .38 .36 4 154 19.5 132 1 10 14 350 .40 .34 7 161 12.5 140 10 16 350 .40 .36 5 164 10.5 142 10 18 350 .40 .38 4 162 19.5 145 1 12 14 350 .42 .34 9 182 14.5 152 12 16 350 .42 .36 7 185 12.5 153 12 18 350 .42 .38 5 182 10.5 155 12 10 350 .42 .40 4 182 19.5 157 1 14 16 350 .47 .36 9 108 14.5 112 14 18 350 .47 .38 7 104 12.4 108 14 10 350 .47 .40 5 100 10.4 100 14 12 350 .47 .42 4 100 9.4 100 1

Sizein. Pressure

Ratingpsi

LargeEnd

SmallEnd

5-18


ANSI/AWWA C153/A21.53Compact Reducers


Table No. 5-14–Continued

L in.

(min)

Weight lb

L in.

(min)

Weight lb

MJ & MJ Large End MJ

16 16 35011.013616.5 144 16 18 350 9.013214.4 136 16 10 350 7.012812.5 128 16 12 350 5.012510.5 119 16 14 350 4.014012.0 138 184 –11.0170 – –18 18 35013.019419.5 195 18 10 35010.019614.0 190 18 12 350 7.018515.0 190 18 14 350 6.019012.5 190 18 16 350 5.019619.0 210 20 6 –16.0232 – – 20 8 –16.0227 – –20 10 35014.022516.0 210 20 12 35012.021017.9 205 20 14 35010.020813.5 220 20 16 350 7.022521.0 290 20 18 350 4.023321.9 335 24 8 –16.0318 – – 24 10 –16.0312 – – 24 12 35016.031021.0 290 24 14 35014.031521.9 335 24 16 35012.032417.5 310 24 18 35010.031218.0 315 24 20 350 7.031513.5 307 30 12 25030.0499 – – 30 16 25030.063339.0 623 30 18 25028.065837.0 635 30 20 25024.062833.0 603 30 24 25010.047824.5 526 36 12 25030.01058 – – 36 16 25030.01016 – – 36 18 25036.0983 – – 36 20 25036.0 97545.0 950 36 24 25019.0 77033.0 810 36 30 25015.5 65024.52758 42 20 250 40.0 – – – 42 24 250 40.0135649.01319 42 30 250 20.0108329.01015 42 36 250 15.5111424.51013 48 20 250 40.0 – – – 48 24 250 40.0 – – – 48 30 250 40.0177949.01711 48 36 250 28.0164137.01540 48 42 250 15.5142624.51274

Sizein. Pressure

Ratingpsi

5-19


AMERICAN StandardWyes

Table No. 5-15

Sizein.

Run Branch

PressureRating*

psiT T1 M N P S

Weight in Pounds

All MJ


14 14 350 .52 .52 12.0 3.0 12.0 – 1195 16 14 350 .55 .52 14.5 3.5 14.5 – 1135 16 16 350 .55 .55 14.5 3.5 14.5 – 1150 18 14 350 .60 .52 17.5 4.5 17.5 – 1190 18 16 350 .60 .55 17.5 4.5 17.5 – 1205 18 18 350 .60 .60 17.5 4.5 17.5 – 1225 10 14 350 .68 .52 20.5 5.0 20.5 – 1270 10 16 350 .68 .55 20.5 5.0 20.5 – 1285 10 18 350 .68 .60 20.5 5.0 20.5 – 1305 10 10 350 .68 .68 20.5 5.0 20.5 – 1375 12 14 350 .75 .52 24.5 5.5 24.5 – 1380 12 16 350 .75 .55 24.5 5.5 24.5 – 1390 12 18 350 .75 .60 24.5 5.5 24.5 – 1415 12 10 350 .75 .68 24.5 5.5 24.5 – 1500 12 12 350 .75 .75 24.5 5.5 24.5 – 1535 14 16 350 .66 .55 27.0 6.0 27.0 – 1565 14 18 350 .66 .60 27.0 6.0 27.0 – 1595 14 10 350 .66 .68 27.0 6.0 27.0 – 1630 14 12 350 .66 .75 27.0 6.0 27.0 – 1690 14 14 350 .66 .66 27.0 6.0 27.0 – 1700 16 16 350 .70 .55 30.0 6.5 30.0 – 1755 16 18 350 .70 .60 30.0 6.5 30.0 – 1790 16 10 350 .70 .68 30.0 6.5 30.0 – 1850 16 12 350 .70 .75 30.0 6.5 30.0 – 1905 16 14 350 .70 .66 30.0 6.5 30.0 – 1865 16 16 350 .70 .70 30.0 6.5 30.0 – 890 18 16 350 .75 .55 25.0 1.0 27.5 – 1960 18 18 350 .75 .60 25.0 1.0 27.5 – 1015 18 10 350 .75 .68 32.0 7.0 32.0 – 1070 18 12 350 .75 .75 32.0 7.0 32.0 – 1130 18 14 350 .75 .66 32.0 7.0 32.0 – 1115 18 16 350 .75 .70 32.0 7.0 32.0 – 1150 18 18 350 .75 .75 32.0 7.0 32.0 – 1190

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.Wyedimensionsvarybetweenmanufacturers.Numeralsoncutsindicatestandardorderofspecifyingsizeoffitting.

5-20


AMERICAN StandardWyes

Wyes Are Special...

...and if a standard tee and 45° bend, as shown, can satisfactorilymeet the requirement—particularly in large–diameter piping—it may be advantageous to use them.

Note:Welded–onlateraloutletsmaybepreferabletowyesinsomecasesfromalayout,installationandeconomicalstandpoint.SeeSection7.


Sizein.

Run Branch

PressureRating*

psiT T1 M N P S

Weight in Pounds

All MJ


204 350 .80 .52 27.0 – 29.5 1250206 350 .80 .55 27.0 – 29.5 1300208 350 .80 .60 27.0 – 29.5 136520 10 350 .80 1.68 27.0 1 1.0 29.5 – 11435 20 12 350 .80 1.75 35.0 1 8.0 35.0 – 1 540 20 14 350 .80 1.66 35.0 1 8.0 35.0 – 1 565 20 16 350 .80 1.70 35.0 1 8.0 35.0 – 1 595 20 18 350 .80 1.75 35.0 1 8.0 35.0 – 1 630 20 20 350 .80 1.80 35.0 1 8.0 35.0 – 1 690 246 350 .89 1.5531.5 0.5 31.5 953248 350 .89 1.60 31.5 0.0 34.5 162524 12 350 .89 1.75 31.5 1 0.5 34.5 – 11700 24 14 350 .89 1.66 40.5 1 9.0 40.5 – 11760 24 16 350 .89 1.70 40.5 1 9.0 40.5 – 11815 24 18 350 .89 1.75 40.5 1 9.0 40.5 – 11880 24 20 350 .89 1.80 40.5 1 9.0 40.5 – 11950 24 24 350 .89 1.89 40.5 1 9.0 40.5 – 12115 30 12 250 1.03 1.75 49.0 10.00 49.0 18.0 12850 30 16 250 1.03 1.70 49.0 10.00 49.0 18.0 12975 30 18 250 1.03 1.75 49.0 10.00 49.0 18.0 13040 30 20 250 1.03 1.80 80.0 10.00 49.0 18.0 13115 30 24 250 1.03 1.89 49.0 10.00 49.0 18.0 13280 30 30 250 1.03 1.03 52.5 18.25 52.5 26.25 13670 36 12 250 1.15 .75 54.0 15.25 54.0 4895 36 14 250 1.15 .66 54.0 15.25 54.0 23.25 14970 36 16 250 1.15 .70 54.0 15.25 54.0 23.25 15040 36 18 250 1.15 .75 54.0 15.25 54.0 23.25 15120 36 20 250 1.15 .80 54.0 15.25 54.0 23.25 15205 36 24 250 1.15 .89 54.0 15.25 54.0 23.25 15390 36 30 250 1.15 1.03 56.0 15.25 56.0 23.25 15805 36 36 250 1.15 1.15 60.0 19.50 60.0 27.5 16335 42 24 250 1.28 .89 60.0 12.00 60.0 – 1 – 48 36 250 1.96 1.58 64.0 5.0 68.0 – 9065

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.*HigherpressureratedWyesmaybeavailableinsomesizes.CheckAMERICAN.Numeralsoncutsindicatestandardorderofspecifyingsizeoffitting.Otherjoints(e.g.Fastite,Flex–Ring,orLok–Ring)areavailableinsomesizes.CheckAMERICAN.

AMERICAN Ductile Iron Mechanical Joint FittingsAMERICAN Standard

Compact Wyes

5-21

Table No. 5-16

Sizein.

Run Branch

PressureRating*

psi M N P All MJ

Dimensions in Inches Weight in Pounds

14 14 250 9.5 2.5 19.5 145 16 16 25013.0 3.0 13.0 193 18 18 25016.0 3.5 16.0 136 10 10 25019.0 3.5 19.0 199 12 12 25022.5 4.5 22.5 272 14 14 25025.0 6.0 25.0 465 16 16 25028.0 6.5 28.0 575 18 18 35030.06.5 30.0 500 20 20 35033.08.0 33.0 747 24 24 35038.59.0 38.51061 30 30 350 50.010.0 50.02200 36 30 350 54.015.0 54.02491.47 36 36 350 57.515.0 57.54754 42 42 350 68.015.0 68.04048 48 48 350 75.016.0 75.0 –

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.Numeralsoncutsindicatestandardorderofspecifyingsizeoffitting.*HigherpressureratedWyesmaybeavailableinsomesizes.CheckAMERICAN.

5-22

AMERICAN Ductile Iron Mechanical Joint FittingsANSI/AWWA C110/A21.10, C153/A21.53, and AMERICAN Standard

Sleeves

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.Inmanycases,fabricatedsleeves/couplingsaccomplishthesamein–stalla�tionobjectivesasmechanical jointsleeves.“Drop–in”restraintcanbepro�videdbycouplingglandends. (SeeSection9.)Contactmanufacturers fordetails.Fabricatedsleevesarealsoreadilyavailablefromvariousmanufacturersforcouplingductileironpipeplainendstopipeplainendsofothermaterialtypesandotheroutsidediameters.

14 350 .34 7.5 117 12.0 1120 16 350 .36 7.5 128 12.0 1133 18 350 .38 7.5 138 12.0 1146 10 350 .40 7.5 149 12.0 1162 12 350 .42 7.5 156 12.0 1176 14 350 .47 9.5 111 15.0 1140 16 350 .50 9.5 123 15.0 1170 18 350 .54 9.0 160 15.0 1200 20 350 .57 9.0 195 15.0 1255 24 350 .61 9.0 225 15.0 1335 30 250 .6615.0 423 24.0 1640 36 250 .7415.0 591 24.0 1925 42 250 .8215.0 788 24.0 1390 48 250 .9015.0978 24.0 1740

Table No. 5-17 AWWA C153-Compact


Sizein.

SolidSleeves

Lengthin.

Weightlb

PressureRating

psi

Sizein.

PressureRating

psiTin.

Tin.

Short Long

Lengthin.

Weightlb

Lengthin.

Weightlb

30 250 1.03 15 635 36 250 1.1515 855 42 250 1.28 24 1550 42 250 1.78 – – 48 250 1.42 24 1940 48 250 1.96 – –

5-23


Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.Normally,sizes12”andsmallercapsandplugsareflatand14”andlargeraredished.Thisissubjecttochangedependingonfoundryequipment.Capsandplugscanbefurnishedtappedforserviceconnectionsortestingpurposes.ThicknessesandweightsofsomecapsandplugsmaybemorethanspecifiedinAWWAC153.

14 350 .46 11 9 1110 16 350 .46 1115 1116 18 350 .46 1122 1126 10 350 .56 1132 1136 12 350 .56 1142 1146 14 350 .62 1166 1175 16 350 .62 1 92 1195 18 350 .65 1114 1121 20 350 .66 1125 1135 24 350 .68 1166 1175 30 250 .76 345 355 36 250 .76 628 688 42 250 .76 665 815 48 250 .76 901 1085

Table No. 5-19

Sizein.

PressureRating

psiTin.

WeightinPounds

MJCap MJPlug

Ifdimensionsand/orweightsforthisfittingarecritical,pleasecontactyourAMERICANcustomerservicerepresentativeforassistance.AllcenterdimensionsreflecttheC153standardminimumdimension.Normally,30”andlargercapsandplugsaredished.Thisissubjecttochangedependingonfoundryequipment.Capsandplugscanbefurnishedtappedforserviceconnectionsortestingpurposes.Aliftingeyeisfurnishedonall30”andlargercapsandplugs.ThicknessesandweightsofsomecapsandplugsmaybemorethanspecifiedinAWWAC110.

30 250 1.03 590 573 36 250 1.15 850 815 42 250 1.28 1180 1110 48 250 1.42 1595 1455

Table No. 5-20

Sizein.

PressureRating

psiTin.

WeightinPounds

MJCap MJPlug

ANSI/AWWA C153/A21.53Compact Caps and Plugs

ANSI/AWWA C110/A21.10Caps and Plugs

5-24

AMERICAN Ductile Iron Mechanical Joint FittingsANSI/AWWA C153/A21.53

AMERICAN StandardSwivel Tees and Glands

Table No. 5-21

Swivel Glands

Table No. 5-22

Sizein.

Run Branch

PressureRating

psi T(nom)

T1(nom) H J

Dimensions in Inches Weight in lbs.

16 6 350 .36 .36 5.0 19.00 157 18 6 350 .38 .36 5.0 10.00 171 18 8 350 .38 .38 6.5 10.25 184 10 6 350 .40 .36 5.0 11.00 193 10 8 350 .40 .38 6.5 11.25 109 12 6 350 .42 .36 5.0 12.25 113 12 8 350 .42 .38 6.5 12.50 130

Sizein. 6 8

Wt.

5 7

MJ and Swivel Tees


5-25

AMERICAN Ductile Iron Mechanical Joint FittingsANSI/AWWA C111/A21.11

AMERICAN StandardGlands

Table No. 5-23

14 7 16 12 18 16 10 22 12 28 14 45 16 52 18 62 20 75 24 97 30 196 36 246 42 302 48 380

Sizein.

Weight inPounds*

Gland


*Glandweightsmaybelessthanshownbecauseofpatternchanges.

Special Glands

MJ Glands for “D” pattern pipe are special and cannot be interchanged with standardMJ Glands or MJ Split Glands. MJ Transition gaskets in the 12” and smaller sizes are used with standard MJ glands for connections to steel pipe O.D. products. Transition sleeves, glands, and gaskets are no longer available in the 14” and larger sizes. (See footnote under Table 5-19.) Various designs of MJ retainer gland devices, designed and manufactured by others, are available. AMERICAN does not warrant the performance of joints utilizing such devices; however, AMERICAN has designed and does manufacture a number of restrained joints, such as Fast-Grip, Flex-Ring, Field Flex-Ring, Lok-Ring, and Flex-Lok shown in Sec-tion 9, that do carry AMERICAN’s standard warranty.

AMERICAN reserves the right to modify or change designs, materials, specifications, or dimensions shown herein without prior notice.

This is a preprint of a section from the 19th Edition of the AMERICAN Pipe Manual. References may be made in this section to other sections of this manual.

APM5—REV—12-15

AMERICAN DUCTILE IRON PIPE

®

section 5 american ductile iron mechanical joint · pdf fileamerican ductile iron mechanical...

Documents