safety data sheet styrene monomer 10 - 15 ppm inhib · safety data sheet styrene monomer 10 ... for...
TRANSCRIPT
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 1 / 20 Styrene Monomer 10 - 15 PPM Inhib
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
Product name : Styrene Monomer 10 - 15 PPM Inhib
Manufacturer or supplier's details
Company : Nexeo Solutions LLC
Address 3 Waterway Square Place Suite 1000
Woodlands, Tx. 77380
United States of America
Emergency telephone number:
Health North America: 1-855-NEXEO4U (1-855-639-3648)
Health International: 1-855-NEXEO4U (1-855-639-3648)
Transport North America: CHEMTREC 800.424.9300
Additional Infor-
mation:
: Responsible Party: Product Safety Group
E-Mail: [email protected]
SDS Requests: 1-855-429-2661
SDS Requests Fax: 1-281-500-2370
Website: www.nexeosolutions.com
SECTION 2. HAZARDS IDENTIFICATION
GHS Classification
Flammable liquids
: Category 3
Acute toxicity
(Inhalation)
: Category 4
Skin irritation
: Category 2
Eye irritation
: Category 2A
Carcinogenicity
: Category 2
Specific target organ tox-
icity - single exposure
: Category 3 (Respiratory system)
Specific target organ tox-
icity - repeated exposure
(Inhalation)
: Category 1 (Auditory system)
Aspiration hazard
: Category 1
GHS Label element
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 2 / 20 Styrene Monomer 10 - 15 PPM Inhib
Hazard pictograms
:
Signal word
: Danger
Hazard statements
: H226 Flammable liquid and vapour.
H304 May be fatal if swallowed and enters airways.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
H372 Causes damage to organs (Auditory system)
through prolonged or repeated exposure if inhaled.
Precautionary statements
: Prevention:
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have
been read and understood.
P210 Keep away from heat, hot surfaces, sparks, open
flames and other ignition sources. No smoking.
P233 Keep container tightly closed.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrical/ ventilating/
lighting/ equipment.
P242 Use only non-sparking tools.
P243 Take precautionary measures against static
discharge.
P260 Do not breathe dust/ fume/ gas/ mist/ vapours/
spray.
P264 Wash skin thoroughly after handling.
P270 Do not eat, drink or smoke when using this
product.
P271 Use only outdoors or in a well-ventilated area.
P280 Wear protective gloves/ eye protection/ face
protection.
P281 Use personal protective equipment as required.
Response:
P301 + P310 IF SWALLOWED: Immediately call a
POISON CENTER or doctor/ physician.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/
Take off immediately all contaminated clothing. Rinse
skin with water/ shower.
P304 + P340 + P312 IF INHALED: Remove victim to
fresh air and keep at rest in a position comfortable for
breathing. Call a POISON CENTER or doctor/ physician if
you feel unwell.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 3 / 20 Styrene Monomer 10 - 15 PPM Inhib
water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
P308 + P313 IF exposed or concerned: Get medical
advice/ attention.
P331 Do NOT induce vomiting.
P332 + P313 If skin irritation occurs: Get medical
advice/ attention.
P337 + P313 If eye irritation persists: Get medical
advice/ attention.
P362 Take off contaminated clothing and wash before
reuse.
P370 + P378 In case of fire: Use dry sand, dry chemical
or alcohol-resistant foam for extinction.
Storage:
P403 + P233 Store in a well-ventilated place. Keep
container tightly closed.
P403 + P235 Store in a well-ventilated place. Keep cool.
P405 Store locked up.
Disposal:
P501 Dispose of contents/ container to an approved
waste disposal plant.
Potential Health Effects
Carcinogenicity:
IARC
Group 2B: Possibly carcinogenic to humans
100-42-5
Styrene
ACGIH
No component of this product present at levels greater
than or equal to 0.1% is identified as a carcinogen or
potential carcinogen by ACGIH.
OSHA
No component of this product present at levels greater
than or equal to 0.1% is identified as a carcinogen or
potential carcinogen by OSHA.
NTP
Reasonably anticipated to be a human carcinogen
100-42-5
Styrene
Emergency Overview
CAUTION!
Appearance
liquid
Colour
colourless, yellow
Odour aromatic, sweet
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 4 / 20 Styrene Monomer 10 - 15 PPM Inhib
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance / Mixture
: Substance
Hazardous components
CAS-No. Chemical Name Concentration (%)
100-42-5 Styrene 90 - 100
Molecular formula
: C6H5-CH=CH2
SECTION 4. FIRST AID MEASURES
General advice
: Move out of dangerous area.
Show this safety data sheet to the doctor in attend-
ance.
Do not leave the victim unattended.
If inhaled
: Consult a physician after significant exposure.
If unconscious place in recovery position and seek
medical advice.
In case of skin contact
: If skin irritation persists, call a physician.
If on skin, rinse well with water.
If on clothes, remove clothes.
In case of eye contact
: Immediately flush eye(s) with plenty of water.
Remove contact lenses.
Protect unharmed eye.
Keep eye wide open while rinsing.
If eye irritation persists, consult a specialist.
If swallowed
: Keep respiratory tract clear.
Do not give milk or alcoholic beverages.
Never give anything by mouth to an unconscious per-
son.
If symptoms persist, call a physician.
Most important symp-
toms and effects, both
acute and delayed
: Causes skin and eye irritation.
Risk of serious damage to the lungs (by aspiration).
SECTION 5. FIREFIGHTING MEASURES
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 5 / 20 Styrene Monomer 10 - 15 PPM Inhib
Suitable extinguishing
media
: Alcohol-resistant foam
Carbon dioxide (CO2)
Dry chemical
Unsuitable extinguishing
media
: High volume water jet
Specific hazards during
firefighting
: Do not allow run-off from fire fighting to enter drains
or water courses.
Hazardous combustion
products
:
Carbon oxides
Specific extinguishing
methods
: Use a water spray to cool fully closed containers.
Collect contaminated fire extinguishing water sepa-
rately. This must not be discharged into drains.
Further information : Fire residues and contaminated fire extinguishing wa-
ter must be disposed of in accordance with local regu-
lations.
For safety reasons in case of fire, cans should be
stored separately in closed containments.
Special protective equip-
ment for firefighters
: Wear self-contained breathing apparatus for fire-
fighting if necessary.
NFPA Flammable and Combustible Liquids Classification:
Flammable Liquid Class IC
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions,
protective equipment and
emergency procedures
: Use personal protective equipment.
Ensure adequate ventilation.
Remove all sources of ignition.
Evacuate personnel to safe areas.
Beware of vapours accumulating to form explosive
concentrations. Vapours can accumulate in low areas.
Environmental precau-
tions
: Prevent product from entering drains.
Prevent further leakage or spillage if safe to do so.
If the product contaminates rivers and lakes or drains
inform respective authorities.
Methods and materials
for containment and
cleaning up
: Contain spillage, and then collect with non-
combustible absorbent material, (e.g. sand, earth,
diatomaceous earth, vermiculite) and place in con-
tainer for disposal according to local / national regula-
tions (see section 13).
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 6 / 20 Styrene Monomer 10 - 15 PPM Inhib
SECTION 7. HANDLING AND STORAGE
Advice on safe handling
: Avoid formation of aerosol.
Do not breathe vapours/dust.
Avoid contact with skin and eyes.
For personal protection see section 8.
Smoking, eating and drinking should be prohibited in
the application area.
Take precautionary measures against static discharg-
es.
Provide sufficient air exchange and/or exhaust in work
rooms.
Open drum carefully as content may be under pres-
sure.
Dispose of rinse water in accordance with local and
national regulations.
Conditions for safe stor-
age
: No smoking.
Keep container tightly closed in a dry and well-
ventilated place.
Containers which are opened must be carefully re-
sealed and kept upright to prevent leakage.
Observe label precautions.
Electrical installations / working materials must com-
ply with the technological safety standards.
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
CAS-No. Components Value type
(Form of
exposure)
Control parame-
ters / Permissi-
ble concentra-
tion
Basis
100-42-5 Styrene TWA 50 ppm
215 mg/m3
NIOSH REL
ST 100 ppm
425 mg/m3
NIOSH REL
TWA 100 ppm OSHA Z-2
CEIL 200 ppm OSHA Z-2
Peak 600 ppm OSHA Z-2
TWA 50 ppm
215 mg/m3
OSHA P0
STEL 100 ppm
425 mg/m3
OSHA P0
TWA 20 ppm ACGIH
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 7 / 20 Styrene Monomer 10 - 15 PPM Inhib
STEL 40 ppm ACGIH
Biological occupational exposure limits
Components CAS-No. Control
parame-
ters
Biological
specimen
Sam-
pling
time
Permissi-
ble con-
centration
Basis
Styrene 100-42-
5
Mandelic
acid plus
phenylgly-
oxylic acid
Urine End of
shift
(As
soon as
possible
after
expo-
sure
ceases)
400 mg/g
Creatinine
ACGIH
BEI
Styrene In ve-
nous
blood
End of
shift
(As
soon as
possible
after
expo-
sure
ceases)
0.2 mg/l ACGIH
BEI
Personal protective equipment
Respiratory protection :
When workers are facing concentrations above the
exposure limit they must use appropriate certified
respirators.
In the case of vapour formation use a respirator with
an approved filter.
Hand protection
Remarks :
The suitability for a specific workplace should be dis-
cussed with the producers of the protective gloves.
Eye protection :
Eye wash bottle with pure water
Tightly fitting safety goggles
Wear face-shield and protective suit for abnormal pro-
cessing problems.
Skin and body protection : impervious clothing
Choose body protection according to the amount and
concentration of the dangerous substance at the work
place.
Hygiene measures : When using do not eat or drink.
When using do not smoke.
Wash hands before breaks and at the end of workday.
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 8 / 20 Styrene Monomer 10 - 15 PPM Inhib
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance
: liquid
Colour
:
colourless, yellow
Odour
:
aromatic, sweet
Odour Threshold
:
0.017 ppm
pH
: 7 @ 20 - 25 °C (68 - 77 °F)
Freezing Point (Freezing
Point)
: -31 °C (-24 °F)
Boiling Point (Boiling
point/boiling range)
: 145 °C (293 °F)
(1,013 hPa)
Flash point
: 31 °C (88 °F)
(1,013 hPa)
Evaporation rate
:
No data available
Flammability (solid, gas)
: No data available
Burning rate
: No data available
Upper explosion limit
: 6.1 %(V)
Lower explosion limit
: 1.1 %(V)
Vapour pressure
: 6.67 hPa @ 20 °C (68 °F)
Relative vapour density
: 3.6 @ 15 - 20 °C (59 - 68 °F)
Relative density
: No data available
Density
: 0.9 g/cm3 @ 20 °C (68 °F)
Bulk density
: No data available
Solubility(ies)
Water solubility
: 320 g/l @ 25 °C (77 °F)
Solubility in other sol-
vents
: soluble
Solvent: Ether
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 9 / 20 Styrene Monomer 10 - 15 PPM Inhib
soluble
Solvent: Acetone
soluble
Solvent: Alcohol
Partition coefficient: n-
octanol/water
: log Pow: 2.96 @ 25 °C (77 °F)
Auto-ignition temperature
: 490 °C1,013 hPa
Thermal decomposition
:
No data available
Viscosity
Viscosity, dynamic
: 0.696 mPa.s @ 25 °C (77 °F)
Viscosity, kinematic
: 0.696 mm2/s @ 25 °C (77 °F)
Oxidizing properties
: The substance or mixture is not classified as oxidizing.
SECTION 10. STABILITY AND REACTIVITY
Reactivity
:
No dangerous reaction known under conditions of
normal use.
Chemical stability
:
Stable under normal conditions.
Possibility of hazardous
reactions
:
Vapours may form explosive mixture with air.
Hazardous polymerization may occur upon depletion
of inhibitor - may cause heat and pressure build-up in
closed containers.
Conditions to avoid
: Keep away from heat, flame, sparks and other ignition
sources.
elevated temperatures
Exposure to light.
Incompatible materials
:
Copper
Oxidizing agents
Strong oxidizing agents
Peroxides
Contamination
polymer catalysts
Alkali metals
aluminum chloride
Strong acids
strong alkalis
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 10 / 20 Styrene Monomer 10 - 15 PPM In-
hib
Copper alloys
metal halogenates
Hazardous decomposition
products
: acrid smoke and fumes
carbon dioxide and carbon monoxide
Hydrocarbons
SECTION 11. TOXICOLOGICAL INFORMATION
Acute toxicity
Product:
Acute oral toxicity
:
Acute toxicity estimate : 2,647 mg/kg
Method: Calculation method
Acute inhalation toxicity
:
Acute toxicity estimate : 12 mg/l
Exposure time: 4 h
Test atmosphere: vapour
Method: Calculation method
Components:
100-42-5:
Acute oral toxicity
:
LD50 (rat): 2,650 mg/kg
Acute inhalation toxicity
:
LC50 (rat): 12 mg/l
Exposure time: 4 h
Assessment: The component/mixture is moderately
toxic after short term inhalation.
Acute dermal toxicity
:
LD50 (rabbit, male and female): > 2,000 mg/kg
Method: OECD Test Guideline 402
GLP: yes
Skin corrosion/irritation
Product:
Remarks: Irritating to skin.
Components:
100-42-5:
Species: rabbit
Result: Irritating to skin.
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 11 / 20 Styrene Monomer 10 - 15 PPM In-
hib
Serious eye damage/eye irritation
Product:
Remarks: Severe eye irritation
Components:
100-42-5:
Species: rabbit
Result: Irritating to eyes.
Respiratory or skin sensitisation
Components:
100-42-5:
Remarks: No data available
Germ cell mutagenicity
Components:
100-42-5:
Genotoxicity in vitro
: Test Type: Chromosome aberration test in vitro
Test species: Human lymphocytes
Metabolic activation: Without metabolic activation
Method: OECD Test Guideline 473
Result: positive
GLP: No data available
: Test Type: Ames test
Test species: Salmonella typhimurium
Metabolic activation: with and without metabolic acti-
vation
Method: OECD Test Guideline 471
Result: Positive results were obtained in some in vitro
tests.
GLP: No data available
: Test Type: Sister chromatid exchange assay in mam-
malian cells
Test species: Human lymphocytes
Metabolic activation: Without metabolic activation
Method: OECD Test Guideline 479
Result: positive
GLP: No data available
Genotoxicity in vivo
:
Test Type: DNA damage and/or repair
Test species: rat (male and female)
Application Route: Inhalation
Exposure time: 2 yr
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 12 / 20 Styrene Monomer 10 - 15 PPM In-
hib
Dose: 0, 0.21, 0.84, 2.1, 4.2 mg/L
Result: Positive results were obtained in some in vivo
tests.
GLP: No data available
Test Type: In vivo micronucleus test
Test species: mouse (male)
Application Route: Inhalation
Method: OECD Test Guideline 474
Result: negative
GLP: yes
Germ cell mutagenicity-
Assessment
:
Animal testing did not show any mutagenic effects.
Carcinogenicity
Components:
100-42-5:
Carcinogenicity - As-
sessment
:
Animal testing did not show any carcinogenic effects.
Reproductive toxicity
Components:
100-42-5:
Effects on foetal devel-
opment
:
Species: rat
Application Route: Inhalation
Dose: 0.519, 1.080, 2.146 mg/l
Duration of Single Treatment: 6 h
Frequency of Treatment: 7 days/week
General Toxicity Maternal: NOAEC: 1.08 mg/L
Developmental Toxicity: NOAEC: 1.08 mg/L
GLP: yes
Reproductive toxicity -
Assessment
:
No evidence of adverse effects on sexual function and
fertility, and on development, based on animal exper-
iments.
No toxicity to reproduction
STOT - single exposure
Product:
No data available
Components:
100-42-5:
Exposure routes: Inhalation
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 13 / 20 Styrene Monomer 10 - 15 PPM In-
hib
Target Organs: Nose
Assessment: May cause respiratory irritation.
STOT - repeated exposure
Product:
No data available
Components:
100-42-5:
Exposure routes: Inhalation
Target Organs: Auditory system
Assessment: Causes damage to organs through prolonged or repeated exposure.
Repeated dose toxicity
Components:
100-42-5:
Species: rat, male
NOAEL: 3.47 mg/l
Application Route: Inhalation
Exposure time: 4 wk
Number of exposures: 6 h/d, 5d/wk
Dose: 3.47, 4.63 mg/L = 750, 1000ppm
Species: rat, male and female
NOAEL: 1,000 mg/kg
LOAEL: 2,000 mg/kg
Application Route: Oral
Exposure time: 78-103 wk
Number of exposures: 5 d/wk
Dose: 500, 1000 and 2000 mg/kg
Target Organs: Liver
Symptoms: death
Repeated dose toxicity -
Assessment
:
May be harmful if swallowed., Harmful if inhaled.,
Causes serious eye irritation., Causes skin irritation.
Aspiration toxicity
Components:
100-42-5:
May be fatal if swallowed and enters airways.
Further information
Product:
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 14 / 20 Styrene Monomer 10 - 15 PPM In-
hib
Remarks: Solvents may degrease the skin.
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
Components:
100-42-5:
Toxicity to fish
:
LC50 (Pimephales promelas (fathead minnow)): 4.02
mg/l
Exposure time: 96 h
Test Type: flow-through test
Toxicity to daphnia and
other aquatic inverte-
brates
:
EC50 (Daphnia magna (Water flea)): 4.7 mg/l
Exposure time: 48 h
Test Type: flow-through test
Method: OECD Test Guideline 202
GLP: yes
Toxicity to algae
:
EC50 (Pseudokirchneriella subcapitata): 4.9 mg/l
Exposure time: 72 h
Test Type: static test
GLP: yes
Remarks: No data available
Toxicity to bacteria
:
GLP:
Remarks: No data available
Ecotoxicology Assessment
Acute aquatic toxicity
:
Toxic to aquatic life.
Persistence and degradability
Components:
100-42-5:
Biodegradability
:
aerobic
Inoculum: Activated sludge, domestic, non-adapted
Result: Readily biodegradable.
Biodegradation: 70.9 %
Exposure time: 28 d
Bioaccumulative potential
Components:
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 15 / 20 Styrene Monomer 10 - 15 PPM In-
hib
100-42-5:
Partition coefficient: n-
octanol/water
: log Pow: 2.95
Mobility in soil
No data available
Other adverse effects
No data available
Product:
Regulation
40 CFR Protection of Environment; Part 82 Protection
of Stratospheric Ozone - CAA Section 602 Class I Sub-
stances
Remarks
This product neither contains, nor was manufactured
with a Class I or Class II ODS as defined by the U.S.
Clean Air Act Section 602 (40 CFR 82, Subpt. A, App.A
+ B).
Additional ecological in-
formation
:
No data available
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Waste from residues : Dispose of in accordance with all applicable local,
state and federal regulations.
For assistance with your waste management needs -
including disposal, recycling and waste stream reduc-
tion, contact NEXEO's Environmental Services Group
at 800-637-7922.
Contaminated packaging : Empty remaining contents.
Dispose of as unused product.
Do not re-use empty containers.
Do not burn, or use a cutting torch on, the empty
drum.
SECTION 14. TRANSPORT INFORMATION
IATA (International Air Transport Association): UN2055, Styrene monomer, stabi-
lized, 3 , III
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 16 / 20 Styrene Monomer 10 - 15 PPM In-
hib
IMDG (International Maritime Dangerous Goods): UN2055, STYRENE MONOMER,
STABILIZED, 3, III, Flash Point:31 °C(88 °F)
DOT (Department of Transportation): UN2055, Styrene monomer, stabilized, 3, III
SECTION 15. REGULATORY INFORMATION
OSHA Hazards
WHMIS Classification
B2
D2A
D2B
:
:
:
:
Flammable liquid, Carcinogen, Moderate skin irritant,
Moderate eye irritant, Moderate respiratory irritant
Flammable liquid
Very Toxic Material Causing Other Toxic Effects
Toxic Material Causing Other Toxic Effects
EPCRA - Emergency Planning and Community Right-to-Know Act
CERCLA Reportable Quantity
Components CAS-No. Component
RQ (lbs)
Calculated product
RQ (lbs)
Styrene 100-42-5 1000 1000
SARA 304 Extremely Hazardous Substances Reportable Quantity
This material does not contain any components with a section 304 EHS RQ.
SARA 311/312
Hazards
:
Fire Hazard
Chronic Health Hazard
Acute Health Hazard
SARA 302
:
SARA 302: No chemicals in this material are subject
to the reporting requirements of SARA Title III,
Section 302.
SARA 313
:
The following components are subject to reporting
levels established by SARA Title III, Section 313:
100-42-5
Styrene 100 %
Clean Air Act
The following chemical(s) are listed as HAP under the U.S. Clean Air Act, Section 12
(40 CFR 61):
100-42-5 Styrene 100 %
100-41-4 Ethylbenzene 0.09 %
96-09-3 Oxirane, 2-phenyl- 0.09 %
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 17 / 20 Styrene Monomer 10 - 15 PPM In-
hib
This product does not contain any chemicals listed under the U.S. Clean Air Act
Section 112(r) for Accidental Release Prevention (40 CFR 68.130, Subpart F).
The following chemical(s) are listed under the U.S. Clean Air Act Section 111 SOCMI
Intermediate or Final VOC's (40 CFR 60.489):
100-42-5 Styrene 100 %
100-41-4 Ethylbenzene 0.09 %
98-83-9 a-Methylstyrene 0.09 %
Clean Water Act
The following Hazardous Substances are listed under the U.S. CleanWater Act, Sec-
tion 311, Table 116.4A:
100-42-5 Styrene 100 %
100-41-4 Ethylbenzene 0.09 %
The following Hazardous Chemicals are listed under the U.S. CleanWater Act, Section
311, Table 117.3:
100-42-5 Styrene 100 %
100-41-4 Ethylbenzene 0.09 %
This product does not contain any toxic pollutants listed under the U.S. Clean Water
Act Section 307
US State Regulations
Massachusetts Right To Know
100-42-5 Styrene 90 - 100 %
96-09-3 Oxirane, 2-phenyl- 0 - 0.1 %
Pennsylvania Right To Know
100-42-5 Styrene 90 - 100 %
100-41-4 Ethylbenzene 0 - 0.1 %
96-09-3 Oxirane, 2-phenyl- 0 - 0.1 %
New Jersey Right To Know
100-42-5 Styrene 90 - 100 %
California Prop 65 WARNING! This product contains a chemical known to
the State of California to cause cancer.
100-41-4 Ethylbenzene
96-09-3 Oxirane, 2-phenyl-
WARNING: This product contains a chemical known to
the State of California to cause birth defects or other
reproductive harm.
98-83-9 a-Methylstyrene
The components of this product are reported in the following inventories:
1907/2006 (EU)
: n (Negative listing)
(Not in compliance
with the inventory)
Switzerland. New notified substances and declared : y (positive listing)
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 18 / 20 Styrene Monomer 10 - 15 PPM In-
hib
preparations
(The formulation
contains substances
listed on the Swiss
Inventory)
United States TSCA Inventory
: y (positive listing)
(On TSCA Invento-
ry)
Canadian Domestic Substances List (DSL)
: y (positive listing)
(All components of
this product are on
the Canadian DSL.)
Australia Inventory of Chemical Substances (AICS)
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
New Zealand. Inventory of Chemical Substances
: n (Negative listing)
(On the inventory,
or in compliance
with the inventory)
Japan. ENCS - Existing and New Chemical
Substances Inventory
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
Japan. ISHL - Inventory of Chemical Substances
(METI)
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
Korea. Korean Existing Chemicals Inventory (KECI)
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
Philippines Inventory of Chemicals and Chemical
Substances (PICCS)
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
China. Inventory of Existing Chemical Substances in
China (IECSC)
: y (positive listing)
(On the inventory,
or in compliance
with the inventory)
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 19 / 20 Styrene Monomer 10 - 15 PPM In-
hib
SECTION 16. OTHER INFORMATION
Further information
NFPA: HMIS III:
The information accumulated is based on the data of which we are aware and is
believed to be correct as of the date hereof. Since this information may be ap-
plied under conditions beyond our control and with which we may be unfamiliar
and since data made become available subsequently to the date hereof, we do
not assume any responsibility for the results of its use. Recipients are advised to
confirm in advance of need that the information is current, applicable, and suita-
ble to their circumstances. This MSDS has been prepared by NEXEO™ Solutions
EHS Product Safety Department (1-855-429-2661) [email protected].
Legecy MSDS:
R0000009
Material number:
16056670, 16045753, 554032, 55665, 88426, 71292, 166708, 55251, 71935,
22000, 22001, 20013, 20012, 20011, 20010
Key or legend to abbreviations and acronyms used in the safety data sheet
ACGIH American Conference of Gov-
ernment Industrial Hygienists
LD50 Lethal Dose 50%
AICS Australia, Inventory of Chem-
ical Substances
LOAEL Lowest Observed Adverse Effect
Level
DSL Canada, Domestic Substanc-
es List
NFPA National Fire Protection Agency
NDSL Canada, Non-Domestic Sub-
stances List
NIOSH National Institute for Occupational
Safety & Health
CNS Central Nervous System NTP National Toxicology Program
Flammability
Health
Insta
bility
2
3
0
FLAMMABILITY
PHYSICAL HAZARD
HEALTH
3
0
2*
Special hazard. 0 = not significant, 1 =Slight, 2 = Moderate, 3 = High 4 =Extreme, * = Chronic
Safety Data Sheet
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Revision Date: 09/25/2014
MSDS Number: 100000009032 20 / 20 Styrene Monomer 10 - 15 PPM In-
hib
CAS Chemical Abstract Service NZloC New Zealand Inventory of Chemicals
EC50 Effective Concentration NOAEL No Observable Adverse Effect Level
EC50 Effective Concentration 50% NOEC No Observed Effect Concentration
EGEST EOSCA Generic Exposure
Scenario Tool
OSHA Occupational Safety & Health Admin-
istration
EOSCA European Oilfield Specialty
Chemicals Association
PEL Permissible Exposure Limit
EINECS European Inventory of Exist-
ing Chemical Substances
PICCS Philipines Inventory of Commercial
Chemical Substances
MAK Germany Maximum Concen-
tration Values
PRNT Presumed Not Toxic
GHS Globally Harmonized System RCRA Resource Conservation Recovery Act
>= Greater Than or Equal To STEL Short-term Exposure Limit
IC50 Inhibition Concentration 50% SARA Superfund Amendments and Reau-
thorization Act.
IARC International Agency for Re-
search on Cancer
TLV Threshold Limit Value
IECSC Inventory of Existing Chemi-
cal Substances in China
TWA Time Weighted Average
ENCS Japan, Inventory of Existing
and New Chemical Substanc-
es
TSCA Toxic Substance Control Act
KECI Korea, Existing Chemical In-
ventory
UVCB Unknown or Variable Compositon,
Complex Reaction Products, and
Biological Materials
<= Less Than or Equal To WHMIS Workplace Hazardous Materials In-
formation System
LC50 Lethal Concentration 50%
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 1 / 22 Styrene Monomer 10 - 15 PPM Inhib
SECTION 1. IDENTIFICATION DU PRODUIT ET DE LA SOCIETE
Nom du produit : Styrene Monomer 10 - 15 PPM Inhib
Détails concernant le fabricant ou le fournisseur
Société : Nexeo Solutions LLC
Adresse 3 Waterway Square Place Suite 1000
Woodlands, Tx. 77380
USA
Numéro d'appel d'urgence:
Santé Amérique du Nord : 1-855-NEXEO4U (1-855-639-3648)
Santé International : 1-855-NEXEO4U (1-855-639-3648)
Transport Amérique du Nord : CHEMTREC 800.424.9300
Renseignements com-
plémentaires :
: Partie responsable : Groupe de la sécurité des produits
E-Mail: [email protected]
Demandes de FDS : 1-855-429-2661
Demandes de FDS par télécopie : 1-281-500-2370
Website: www.nexeosolutions.com
SECTION 2. IDENTIFICATION DES DANGERS
Classification SGH
Liquides inflammables
: Catégorie 3
Toxicité aiguë
(Inhalation)
: Catégorie 4
Irritation cutanée
: Catégorie 2
Irritation oculaire
: Catégorie 2A
Cancérogénicité
: Catégorie 2
Toxicité spécifique pour
certains organes cibles -
exposition unique
: Catégorie 3 (Système respiratoire)
Toxicité spécifique pour
certains organes cibles -
exposition répétée (Inha-
lation)
: Catégorie 1 (Système acoustique)
Danger par aspiration
: Catégorie 1
Élément étiquette SGH
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 2 / 22 Styrene Monomer 10 - 15 PPM Inhib
Pictogrammes de danger
:
Mention d'avertissement
: Danger
Mentions de danger
: H226 Liquide et vapeurs inflammables.
H304 Peut être mortel en cas d'ingestion et de pénétra-
tion dans les voies respiratoires.
H315 Provoque une irritation cutanée.
H319 Provoque une sévère irritation des yeux.
H332 Nocif par inhalation.
H335 Peut irriter les voies respiratoires.
H351 Susceptible de provoquer le cancer.
H372 Risque avéré d'effets graves pour les organes
(Système acoustique) à la suite d'expositions répétées
ou d'une exposition prolongée en cas d'inhalation.
Conseils de prudence
: Prévention:
P201 Se procurer les instructions avant utilisation.
P202 Ne pas manipuler avant d'avoir lu et compris
toutes les précautions de sécurité.
P210 Tenir à l’écart de la chaleur, des surfaces chaudes,
des étincelles, des flammes nues et de toute autre
source d’inflammation. Ne pas fumer.
P233 Maintenir le récipient fermé de manière étanche.
P240 Mise à la terre/liaison équipotentielle du récipient
et du matériel de réception.
P241 Utiliser du matériel électrique/ de ventilation/
d'éclairage/antidéflagrant.
P242 Ne pas utiliser d'outils produisant des étincelles.
P243 Prendre des mesures de précaution contre les dé-
charges électrostatiques.
P260 Ne pas respirer les poussières/ fumées/ gaz/
brouillards/ vapeurs/ aérosols.
P264 Se laver la peau soigneusement après manipula-
tion.
P270 Ne pas manger, boire ou fumer en manipulant ce
produit.
P271 Utiliser seulement en plein air ou dans un endroit
bien ventilé.
P280 Porter des gants de protection/ un équipement de
protection des yeux/ du visage.
P281 Utiliser l'équipement de protection individuel re-
quis.
Intervention:
P301 + P310 EN CAS D'INGESTION: Appeler immédia-
tement un CENTRE ANTIPOISON ou un médecin.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 3 / 22 Styrene Monomer 10 - 15 PPM Inhib
P303 + P361 + P353 EN CAS DE CONTACT AVEC LA
PEAU (ou les cheveux): enlever immédiatement les vê-
tements contaminés. Rincer la peau à l'eau/ se doucher.
P304 + P340 + P312 EN CAS D'INHALATION: transpor-
ter la victime à l'extérieur et la maintenir au repos dans
une position où elle peut confortablement respirer. Ap-
peler un CENTRE ANTIPOISON ou un médecin en cas de
malaise.
P305 + P351 + P338 EN CAS DE CONTACT AVEC LES
YEUX: rincer avec précaution à l'eau pendant plusieurs
minutes. Enlever les lentilles de contact si la victime en
porte et si elles peuvent être facilement enlevées. Con-
tinuer à rincer.
P308 + P313 EN CAS d'exposition prouvée ou suspec-
tée: consulter un médecin.
P331 NE PAS faire vomir.
P332 + P313 En cas d'irritation cutanée: consulter un
médecin.
P337 + P313 Si l'irritation oculaire persiste: consulter
un médecin.
P362 Enlever les vêtements contaminés et les laver
avant réutilisation.
P370 + P378 En cas d'incendie: utiliser du sable sec, de
la poudre chimique sèche ou de la mousse résistant à
l'alcool pour l'extinction.
Stockage:
P403 + P233 Stocker dans un endroit bien ventilé.
Maintenir le récipient fermé de manière étanche.
P403 + P235 Stocker dans un endroit bien ventilé. Tenir
au frais.
P405 Garder sous clef.
Elimination:
P501 Éliminer le contenu/récipient dans une installation
d'élimination des déchets agréée.
Effets potentiels sur la santé
Cancérogénicité:
IARC
Group 2B: Cancérigène possible pour l'Homme
100-42-5
Benzene, ethenyl-
ACGIH
Aucun composant de ce produit présent à des concen-
trations plus grandes que ou égales à 0,1% n'a été
identifié comme cancérigène ni comme cancérigène
possible par ACGIH.
OSHA
Aucun composant de ce produit présent à des concen-
trations plus grandes que ou égales à 0,1% n'a été
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 4 / 22 Styrene Monomer 10 - 15 PPM Inhib
identifié comme cancérigène ni comme cancérigène
possible par OSHA.
NTP
Raisonnablement anticipé cancérogène pour l'homme
100-42-5
Benzene, ethenyl-
Aperçu des urgences
ATTENTION!
Aspect
liquide
Couleur
incolore, jaune
Odeur
aromatique, douce
SECTION 3. COMPOSITION/ INFORMATIONS SUR LES COMPOSANTS
Substance/mélange
: Substance
Composants dangereux
No.-CAS Nom Chimique Concentration (%)
100-42-5 Benzene, ethenyl- 90 - 100
Formule moléculaire
: C6H5-CH=CH2
SECTION 4. PREMIERS SECOURS
Conseils généraux
: S'éloigner de la zone dangereuse.
Montrer cette fiche de données de sécurité au méde-
cin traitant.
Ne pas laisser la victime sans surveillance.
En cas d'inhalation
: Consulter un médecin après toute exposition impor-
tante.
En cas d'inconscience, allonger en position latérale
stable et appeler un médecin.
En cas de contact avec la
peau
: Si l'irritation de la peau persiste, appeler un médecin.
En cas de contact avec la peau, bien rincer à l'eau.
Enlever immédiatement tout vêtement souillé.
En cas de contact avec
les yeux
: Rincer immédiatement l'oeil (les yeux) à grande eau.
Enlever les lentilles de contact.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 5 / 22 Styrene Monomer 10 - 15 PPM Inhib
Protéger l'oeil intact.
Maintenir l'oeil bien ouvert pendant le rinçage.
Si l'irritation oculaire persiste, consulter un médecin
spécialiste.
En cas d'ingestion
: Maintenir l'appareil respiratoire dégagé.
Ne pas faire boire de lait ou de boissons alcoolisées.
Ne jamais rien faire avaler à une personne incons-
ciente.
Si les troubles se prolongent, consulter un médecin.
Principaux symptômes et
effets, aigus et différés
: Cause une irritation cutanée et oculaire.
Risque de dommages importants aux poumons (par
aspiration).
SECTION 5. MESURES DE LUTTE CONTRE L'INCENDIE
Moyens d'extinction ap-
propriés
: Mousse résistant à l'alcool
Dioxyde de carbone (CO2)
Poudre chimique sèche
Moyens d'extinction inap-
propriés
: Jet d'eau à grand débit
Dangers spécifiques pen-
dant la lutte contre
l'incendie
: Ne pas laisser pénétrer l'eau d'extinction contaminée
dans les égouts ou les cours d'eau.
Produits de combustion
dangereux
:
Oxydes de carbone
Méthodes spécifiques
d'extinction
: Utiliser de l'eau pulvérisée pour refroidir complète-
ment les conteneurs fermés.
Collecter séparément l'eau d'extinction contaminée,
ne pas la rejeter dans les canalisations.
Information supplémen-
taire
: Les résidus d'incendie et l'eau d'extinction contaminée
doivent être éliminés conformément à la réglementa-
tion locale en vigueur.
Pour de raisons de sécurité en cas d'incendie, les bi-
dons doivent être entreposés séparément, dans des
enceintes fermées.
Équipement de protection
spécial pour les pompiers
: Porter un appareil de protection respiratoire autonome
pour la lutte contre l'incendie, si nécessaire.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 6 / 22 Styrene Monomer 10 - 15 PPM Inhib
Classe d'Inflammabilité pour Liquides Inflammables:
Liquide inflammable de classe IC
SECTION 6. MESURES À PRENDRE EN CAS DE DISPERSION ACCIDENTELLE
Précautions individuelles,
équipement de protection
et procédures d'urgence
: Utiliser un équipement de protection individuelle.
Assurer une ventilation adéquate.
Enlever toute source d'ignition.
Évacuer le personnel vers des endroits sûrs.
Attention aux vapeurs qui s'accumulent en formant
des concentrations explosives. Les vapeurs peuvent
s'accumuler dans les zones basses.
Précautions pour la pro-
tection de l'environne-
ment
: Éviter que le produit arrive dans les égouts.
Éviter tout déversement ou fuite supplémentaire, si
cela est possible en toute sécurité.
En cas de pollution de cours d'eau, lacs ou égouts,
informer les autorités compétentes conformément aux
dispositions locales.
Méthodes et matériel de
confinement et de net-
toyage
: Contenir et collecter le matériel répandu à l'aide d'un
matériau absorbant non combustible, (p.e. sable,
terre, terre de diatomées, vermiculite) et le mettre
dans un conteneur pour l'élimination conformément
aux réglementations locales / nationales (voir chapitre
13).
SECTION 7. MANIPULATION ET STOCKAGE
Conseils pour une mani-
pulation sans danger
: Éviter la formation d'aérosols.
Ne pas inhaler les vapeurs/poussières.
Éviter le contact avec la peau et les yeux.
Équipement de protection individuel, voir section 8.
Ne pas manger, fumer ou boire dans la zone de tra-
vail.
Éviter l'accumulation de charges électrostatiques.
Prévoir un renouvellement d'air et/ou une ventilation
suffisante dans les ateliers.
Ouvrir les fûts avec précaution, le contenu pouvant
être sous pression.
Eliminer l'eau de rinçage en accord avec les réglemen-
tations locales et nationales.
Conditions de stockage
sures
: Défense de fumer.
Tenir le récipient bien fermé dans un endroit sec et
bien aéré.
Refermer soigneusement tout récipient entamé et le
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 7 / 22 Styrene Monomer 10 - 15 PPM Inhib
stocker verticalement afin d'éviter tout écoulement.
Respecter les mises-en-garde de l'étiquette.
Les installations et le matériel électriques doivent être
conformes aux normes techniques de sécurité.
SECTION 8. CONTRÔLES DE L'EXPOSITION/ PROTECTION INDIVIDUELLE
Composants avec valeurs limites d'exposition professionnelle
No.-CAS Composants Type de
valeur
(Type d'ex-
position)
Paramètres de
contrôle / Con-
centration ad-
missible
Base
100-42-5 Benzene, ethenyl- TWA 50 ppm
215 mg/m3
NIOSH REL
ST 100 ppm
425 mg/m3
NIOSH REL
TWA 100 ppm OSHA Z-2
CEIL 200 ppm OSHA Z-2
Peak 600 ppm OSHA Z-2
TWA 50 ppm
215 mg/m3
OSHA P0
STEL 100 ppm
425 mg/m3
OSHA P0
TWA 20 ppm ACGIH
STEL 40 ppm ACGIH
Valeurs limites biologiques d'exposition au poste de travail
Composants No.-CAS Para-
mètres de
contrôle
Échantil-
lon bio-
logique
Heure
d'échan
tillon-
nage
Concen-
tration
admissible
Base
Benzene, ethenyl- 100-42-
5
Mandelic
acid plus
phenylglyo
xylic acid
Urine End of
shift
(As
soon as
possible
after
expo-
sure
ceases)
400 mg/g
créatinine
ACGIH
BEI
Styrene In ve-
nous
blood
End of
shift
(As
soon as
possible
after
0.2 mg/l ACGIH
BEI
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 8 / 22 Styrene Monomer 10 - 15 PPM Inhib
expo-
sure
ceases)
Équipement de protection individuelle
Protection respiratoire :
Lorsque les travailleurs sont confrontés à des concen-
trations supérieures aux limites d'exposition, ils doi-
vent porter des masques appropriés et agréés.
En cas de formation de vapeurs, utiliser un respirateur
avec un filtre homologué.
Protection des mains
Remarques :
Il convient de discuter au préalable avec le fournisseur
des gants de protection si ceux-ci sont bien adaptés à
un poste de travail spécifique.
Protection des yeux :
Flacon pour le rinçage oculaire avec de l'eau pure
Lunettes de sécurité à protection intégrale
Porter un écran-facial et des vêtements de protection
en cas de problèmes lors de la mise en oeuvre.
Protection de la peau et
du corps
: vêtements étanches
Choisir la protection individuelle suivant la quantité et
la concentration de la substance dangereuse au poste
de travail.
Mesures d'hygiène : Ne pas manger et ne pas boire pendant l'utilisation.
Ne pas fumer pendant l'utilisation.
Se laver les mains avant les pauses et à la fin de la
journée de travail.
SECTION 9. PROPRIÉTÉS PHYSIQUES ET CHIMIQUES
Aspect
: liquide
Couleur
:
incolore, jaune
Odeur
:
aromatique, douce
Seuil olfactif
:
0.017 ppm
pH
: 7 @ 20 - 25 °C (68 - 77 °F)
Freezing Point (Point de
congélation)
: -31 °C (-24 °F)
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 9 / 22 Styrene Monomer 10 - 15 PPM Inhib
Boiling Point
(Point/intervalle d'ébulli-
tion)
: 145 °C (293 °F)
(1,013 hPa)
Point d'éclair
: 31 °C (88 °F)
(1,013 hPa)
Taux d'évaporation
:
Donnée non disponible
Inflammabilité (solide,
gaz)
: Donnée non disponible
Vitesse de combustion
: Donnée non disponible
Limite d'explosivité, supé-
rieure
: 6.1 % (v)
Limite d'explosivité, infé-
rieure
: 1.1 % (v)
Pression de vapeur
: 6.67 hPa @ 20 °C (68 °F)
Densité de vapeur relative
: 3.6 @ 15 - 20 °C (59 - 68 °F)
Densité relative
: Donnée non disponible
Densité
: 0.9 gcm3 @ 20 °C (68 °F)
Masse volumique appa-
rente
: Donnée non disponible
Solubilité(s)
Hydrosolubilité
: 320 g/l @ 25 °C (77 °F)
Solubilité dans d'autres
solvants
: soluble
Solvant: Éther
soluble
Solvant: Acétone
soluble
Solvant: Alcool
Coefficient de partage: n-
octanol/eau
: log Pow: 2.96 @ 25 °C (77 °F)
Température d'auto-
inflammabilité
: 490 °C1,013 hPa
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 10 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Décomposition thermique
:
Donnée non disponible
Viscosité
Viscosité, dynamique
: 0.696 mPa.s @ 25 °C (77 °F)
Viscosité, cinématique
: 0.696 mm2/s @ 25 °C (77 °F)
Propriétés comburantes
: La substance ou le mélange n'est pas classé comme
oxydant.
SECTION 10. STABILITÉ ET RÉACTIVITÉ
Réactivité
:
Pas de réactions dangereuses connues dans les condi-
tions normales d'utilisation.
Stabilité chimique
:
Stable dans des conditions normales.
Possibilité de réactions
dangereuses
:
Des vapeurs peuvent former un mélange explosif avec
l'air.
Une polymérisation dangereuse peut avoir lieu après
l'épuisement de l'agent inhibiteur - peut engendrer
une augmentation de la chaleur et de la pression dans
des récipients fermés.
Conditions à éviter
: Tenir éloigné de la chaleur, des flammes, des étin-
celles et d’autres sources d’inflammation.
températures élevées
Exposition à la lumière.
Matières incompatibles
:
Cuivre
Oxydants
Oxydants forts
Peroxydes
Contamination
catalyseurs polymères
Métaux alcalins
chlorure d’aluminium
Acides forts
alcalis forts
Alliage de cuivre
halogènes métalliques
Produits de décomposition
dangereux
: fumées et vapeurs acres
dioxyde de carbone et monoxyde de carbone
Hydrocarbures
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 11 / 22 Styrene Monomer 10 - 15 PPM In-
hib
SECTION 11. INFORMATIONS TOXICOLOGIQUES
Toxicité aiguë
Produit:
Toxicité aiguë par voie
orale
:
Estimation de la toxicité aiguë : 2,647 mg/kg
Méthode: Méthode de calcul
Toxicité aiguë par inhala-
tion
:
Estimation de la toxicité aiguë : 12 mg/l
Durée d'exposition: 4 h
Atmosphère de test: vapeur
Méthode: Méthode de calcul
Composants:
100-42-5:
Toxicité aiguë par voie
orale
:
DL50 (rat): 2,650 mg/kg
Toxicité aiguë par inhala-
tion
:
CL50 (rat): 12 mg/l
Durée d'exposition: 4 h
Evaluation: Le composant/mélange est modérément
toxique après une inhalation de courte durée.
Toxicité aiguë par voie
cutanée
:
DL50 (lapin, mâle et femelle): > 2,000 mg/kg
Méthode: OCDE ligne directrice 402
BPL: oui
Corrosion cutanée/irritation cutanée
Produit:
Remarques: Irritant pour la peau.
Composants:
100-42-5:
Espèce: lapin
Résultat: Irritant pour la peau.
Lésions oculaires graves/irritation oculaire
Produit:
Remarques: Irritation sévère des yeux
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 12 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Composants:
100-42-5:
Espèce: lapin
Résultat: Irritant pour les yeux.
Sensibilisation respiratoire ou cutanée
Composants:
100-42-5:
Remarques: Donnée non disponible
Mutagénicité sur les cellules germinales
Composants:
100-42-5:
Génotoxicité in vitro
: Type de Test: Test d'aberration chromosomique in
vitro
Espèce utilisée pour le test: Lymphocytes humains
Activation du métabolisme: Sans activation métabo-
lique
Méthode: OCDE ligne directrice 473
Résultat: positif
BPL: Donnée non disponible
: Type de Test: Test de Ames
Espèce utilisée pour le test: Salmonella typhimurium
Activation du métabolisme: avec ou sans activation
métabolique
Méthode: OCDE ligne directrice 471
Résultat: Des résultats positifs ont été obtenus dans
certains tests in vitro.
BPL: Donnée non disponible
: Type de Test: Essai d’échange de chromatides sœurs
dans des cellules de mammifères
Espèce utilisée pour le test: Lymphocytes humains
Activation du métabolisme: Sans activation métabo-
lique
Méthode: OCDE ligne directrice 479
Résultat: positif
BPL: Donnée non disponible
Génotoxicité in vivo
:
Type de Test: Dommage à l’ADN et/ou réparation de
l’ADN
Espèce utilisée pour le test: rat (mâle et femelle)
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 13 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Voie d'application: Inhalation
Durée d'exposition: 2 yr
Dose: 0, 0.21, 0.84, 2.1, 4.2 mg/L
Résultat: Des résultats positifs ont été obtenus dans
certains tests in vivo.
BPL: Donnée non disponible
Type de Test: Test du micronucleus in vivo
Espèce utilisée pour le test: souris (mâle)
Voie d'application: Inhalation
Méthode: OCDE ligne directrice 474
Résultat: négatif
BPL: oui
Mutagénicité sur les cel-
lules germinales- Evalua-
tion
:
Les tests sur les animaux n'ont montré aucun effet
mutagène.
Cancérogénicité
Composants:
100-42-5:
Cancérogénicité - Evalua-
tion
:
Les tests sur les animaux n'ont montré aucun effet
cancérigène.
Toxicité pour la reproduction
Composants:
100-42-5:
Incidences sur le déve-
loppement du fœtus
:
Espèce: rat
Voie d'application: Inhalation
Dose: 0.519, 1.080, 2.146 mg/l
Durée d’un traitement unique: 6 h
Fréquence du traitement: 7 jours / semaine
Toxicité maternelle générale: NOAEC: 1.08 mg/L
Toxicité pour le développement: NOAEC: 1.08 mg/L
BPL: oui
Toxicité pour la reproduc-
tion - Evaluation
:
Aucune preuve d'effets nocifs sur la reproduction et la
fertilité ni la croissance, sur la base d'expériences sur
des animaux.
Pas toxique pour la reproduction
Toxicité spécifique pour certains organes cibles - exposition unique
Produit:
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 14 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Donnée non disponible
Composants:
100-42-5:
Voies d'exposition: Inhalation
Organes cibles: Nez
Evaluation: Peut irriter les voies respiratoires.
Toxicité spécifique pour certains organes cibles - exposition répétée
Produit:
Donnée non disponible
Composants:
100-42-5:
Voies d'exposition: Inhalation
Organes cibles: Système acoustique
Evaluation: Risque avéré d'effets graves pour les organes à la suite d'expositions
répétées ou d'une exposition prolongée.
Toxicité à dose répétée
Composants:
100-42-5:
Espèce: rat, mâle
NOAEL: 3.47 mg/l
Voie d'application: Inhalation
Durée d'exposition: 4 wk
Nombre d'expositions: 6 h/d, 5d/wk
Dose: 3.47, 4.63 mg/L = 750, 1000ppm
Espèce: rat, mâle et femelle
NOAEL: 1,000 mg/kg
LOAEL: 2,000 mg/kg
Voie d'application: Oral(e)
Durée d'exposition: 78-103 wk
Nombre d'expositions: 5 d/wk
Dose: 500, 1000 and 2000 mg/kg
Organes cibles: Foie
Symptômes: décès
Toxicité à dose répétée -
Evaluation
:
Peut être nocif par ingestion., Nocif par inhalation.,
Provoque une sévère irritation des yeux., Provoque
une irritation cutanée.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 15 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Toxicité par aspiration
Composants:
100-42-5:
Peut être mortel en cas d'ingestion et de pénétration dans les voies respiratoires.
Information supplémentaire
Produit:
Remarques: Les solvants risquent de dessécher la peau.
SECTION 12. INFORMATIONS ÉCOLOGIQUES
Écotoxicité
Composants:
100-42-5:
Toxicité pour les poissons
:
CL50 (Pimephales promelas (Vairon à grosse tête)):
4.02 mg/l
Durée d'exposition: 96 h
Type de Test: Essai en dynamique
Toxicité pour la daphnie
et les autres invertébrés
aquatiques
:
CE50 (Daphnia magna (Grande daphnie )): 4.7 mg/l
Durée d'exposition: 48 h
Type de Test: Essai en dynamique
Méthode: OCDE Ligne directrice 202
BPL: oui
Toxicité pour les algues
:
CE50 (Pseudokirchneriella subcapitata): 4.9 mg/l
Durée d'exposition: 72 h
Type de Test: Essai en statique
BPL: oui
Remarques: Donnée non disponible
Toxicité pour les bacté-
ries
:
BPL:
Remarques: Donnée non disponible
Évaluation Ecotoxicologique
Toxicité aiguë pour le
milieu aquatique
:
Toxique pour les organismes aquatiques.
Persistance et dégradabilité
Composants:
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 16 / 22 Styrene Monomer 10 - 15 PPM In-
hib
100-42-5:
Biodégradabilité
:
aérobique
Inoculum: Boues activées, domestiques, non adap-
téees
Résultat: Facilement biodégradable.
Biodégradation: 70.9 %
Durée d'exposition: 28 jr
Potentiel de bioaccumulation
Composants:
100-42-5:
Coefficient de partage: n-
octanol/eau
: log Pow: 2.95
Mobilité dans le sol
Donnée non disponible
Autres effets néfastes
Donnée non disponible
Produit:
Réglementation
Remarques
Ce produit ni ne contient, ni n'a été fabriqué avec ODS
de Classe I ou de Classe II au sens défini par "U.S.
Clean Air Act Section 602 (40 CFR 82, Subpt. A, App.A
+ B").
Information écologique
supplémentaire
:
Donnée non disponible
SECTION 13. CONSIDÉRATIONS RELATIVES À L'ÉLIMINATION
Méthodes d'élimination
Déchets de résidus : Éliminer les substances conformément aux réglemen-
tations locales, nationales et fédérales en vigueur.
Pour obtenir de l'assistance relativement à vos be-
soins en matière de gestion des déchets, notamment
l'élimination, le recyclage et la réduction du flux des
déchets, communiquez avec le Groupe des services
environnementaux d'NEXEO, au 800-637-7922.
Emballages contaminés : Vider les restes.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 17 / 22 Styrene Monomer 10 - 15 PPM In-
hib
Eliminer comme produit non utilisé.
Ne pas réutiliser des récipients vides.
Ne pas brûler les fûts vides ni les exposer au chalu-
meau.
SECTION 14. INFORMATIONS RELATIVES AU TRANSPORT
IATA (International Air Transport Association): UN2055, STYRENE MONOMER,
STABILIZED, 3 , III
IMDG (International Maritime Dangerous Goods): UN2055, STYRENE MONOMER,
STABILIZED, 3, III, Flash Point:31 °C(88 °F)
DOT (Department of Transportation): UN2055, STYRENE MONOMER, STABILIZED, 3,
III
SECTION 15. INFORMATIONS RÉGLEMENTAIRES
Risques selon l'OSHA
Classification de
SIMDUT
B2
D2A
D2B
:
:
:
:
Liquide inflammable, Produit cancérogène, Produit
irritant modéré de la peau, Produit irritant modéré
pour les yeux, Irritant modéré pour le système respi-
ratoire
Liquide inflammable
Matière très toxique qui provoque d'autres effets
toxiques
Matière toxique qui provoque d'autres effets toxiques
EPCRA - Plan d'Urgence et Droit de Savoir des Collectivités [Emergency
Planning Community Rght-to-Know]
CERCLA Quantité à reporter
Composants No.-CAS Component
RQ (lbs)
Calculated product
RQ (lbs)
Benzene, ethenyl- 100-42-5 1000 1000
SARA 304 Substances Extrêmement Dangereuses Quantité à reporter
Cette matière ne contient aucun composant avec une RQ en section 304 de EHS.
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 18 / 22 Styrene Monomer 10 - 15 PPM In-
hib
SARA 311/312 Dan-
gers
:
Risque d'incendie
Danger chronique pour la santé
Danger aigu pour la santé
SARA 302
:
SARA 302: Aucun composé chimique dans cette ma-
tière n'est soumis aux exigences de déclaration selon
SARA Titre III, Section 302.
SARA 313
:
SARA Titre III, Section 313 établit des concentrations
auxquelles les composés suivants sont soumis à dé-
claration:
100-42-5
Benzene, ethenyl- 100 %
Loi sur l'Air Propre [Clean Air Act - USA]
Le(s) produit(s) chimique(s) suivant(s) est(sont) listé(s) comme HAP dans "U.S.
Clean Air Act, Section 12 (40 CFR 61)":
100-42-5 Benzene, ethenyl- 100 %
100-41-4 Ethylbenzene 0.09 %
96-09-3 Oxirane, 2-phenyl- 0.09 %
Ce produit ne contient aucune substance chimique listée dans le U.S. Clean Air Act
Section 112(r) for Accidental Release Prevention (40 CFR 68.130, Subpart F).
Le(s) produit(s) chimique(s) suivant est/sont listé(s) dans le U.S. Clean Air Act Sec-
tion 111 SOCMI Intermediate or Final VOCs (40 CFR 60.489):
100-42-5 Benzene, ethenyl- 100 %
100-41-4 Ethylbenzene 0.09 %
98-83-9 a-Methylstyrene 0.09 %
Clean Water Act [Loi US sur les Eaux]
Les Produits Chimiques Dangereux suivants sont listés dans la U.S. CleanWater Act,
Section 311, Table 116.4A:
100-42-5 Benzene, ethenyl- 100 %
100-41-4 Ethylbenzene 0.09 %
Les Produits Chimiques Dangereux suivants sont listés dans la U.S. CleanWater Act,
Section 311, Table 117.3:
100-42-5 Benzene, ethenyl- 100 %
100-41-4 Ethylbenzene 0.09 %
Ce produit ne contient pas les polluants toxiques suivants, énumérés selon la Section
307 de l'US Clean Water Act
US State Regulations
Massachusetts Right To Know
100-42-5 Benzene, ethenyl- 90 - 100 %
96-09-3 Oxirane, 2-phenyl- 0 - 0.1 %
Pennsylvania Right To Know
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 19 / 22 Styrene Monomer 10 - 15 PPM In-
hib
100-42-5 Benzene, ethenyl- 90 - 100 %
100-41-4 Ethylbenzene 0 - 0.1 %
96-09-3 Oxirane, 2-phenyl- 0 - 0.1 %
New Jersey Right To Know
100-42-5 Benzene, ethenyl- 90 - 100 %
California Prop 65 ATTENTION! Selon l'Etat de Californie ce produit con-
tient une substance chimique qui provoque du cancer.
100-41-4 Ethylbenzene
96-09-3 Oxirane, 2-phenyl-
ATTENTION: Selon l'Etat de Californie ce produit con-
tient une substance chimique qui provoque des mal-
formations congénitales ou d'autres dommages re-
productives.
98-83-9 a-Methylstyrene
Les composants de ce produit figurent dans les inventaires suivants:
1907/2006 (UE)
: n (liste négative)
(N'est pas en con-
formité avec l'inven-
taire)
La Suisse. Substances nouvelles notifiées et com-
muniquées
: y (liste positive) (La
formulation contient
des substances lis-
tées dans l'Inven-
taire Suisse)
Inventaire du TSCA des États-Unis
: y (liste positive)
(Dans l'inventaire
TSCA)
Liste canadienne intérieure des substances (LIS)
: y (liste positive)
(Tous les compo-
sants de ce produit
sont sur la liste ca-
nadienne LIS.)
Inventaire australien des substances chimiques
(Australia Inventory of Chemical Substances, AICS)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Nouvelle-Zélande. Inventaire des substances chi-
miques
: n (liste négative)
(Listé ou en confor-
mité avec l'inven-
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 20 / 22 Styrene Monomer 10 - 15 PPM In-
hib
taire)
Japon. Inventaire des substances chimiques exis-
tantes et nouvelles (Existing and New Chemical
Substances Inventory, ENCS)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Japon. ISHL - Inventaire des substances chimiques
(METI)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Corée. Inventaire coréen des produits chimiques
existants (Korean Existing Chemicals Inventory,
KECI)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Inventaire philippin des substances et produits chi-
miques (Philippines Inventory of Chemicals and
Chemical Substances, PICCS)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Chine. Inventaire chinois des substances chimiques
existantes (Inventory of Existing Chemical Subs-
tances in China, IECSC)
: y (liste positive)
(Listé ou en confor-
mité avec l'inven-
taire)
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 21 / 22 Styrene Monomer 10 - 15 PPM In-
hib
SECTION 16. AUTRES INFORMATIONS
Information supplémentaire
NFPA: HMIS III:
Les renseignements fournis dans ce document sont réputés précis mais rien ne
garantit quils proviennent de la société ou non. Il est recommandé aux destina-
taires de vérifier à lavance si les renseignements sont actuels, valides et adéquats
pour leur situation personnelle. La présente fiche technique a été élaborée par le
service de la sécurité et de la santé NEXEO™ Solutions EHS Product Safety De-
partment (1-855-429-2661) [email protected].
Ancienne FDS :
R0000009
Numéro de la matière:
16056670, 16045753, 554032, 55665, 88426, 71292, 166708, 55251, 71935,
22000, 22001, 20013, 20012, 20011, 20010
Key or legend to abbreviations and acronyms used in the safety data sheet
ACGIH American Conference of Gov-
ernment Industrial Hygienists
LD50 Lethal Dose 50%
AICS Australia, Inventory of Chem-
ical Substances
LOAEL Lowest Observed Adverse Effect
Level
DSL Canada, Domestic Substanc-
es List
NFPA National Fire Protection Agency
NDSL Canada, Non-Domestic Sub-
stances List
NIOSH National Institute for Occupational
Safety & Health
CNS Central Nervous System NTP National Toxicology Program
CAS Chemical Abstract Service NZloC New Zealand Inventory of Chemicals
EC50 Effective Concentration NOAEL No Observable Adverse Effect Level
EC50 Effective Concentration 50% NOEC No Observed Effect Concentration
Inflammabilité
Santé
Insta
bilité
2
3
0
INFLAMMABILITE
DANGER PHYSIQUE
SANTE
3 0
2*
Danger particulier. 0 = insignifiante, 1 =Léger, 2 = Modéré, 3 = Elevé 4 =Extrême, * = Chronique
Fiche de Données de Sécurité / Fiche Si-gnalétique
Styrene Monomer 10 - 15 PPM Inhib
Version 0.0 Date de révision: 09/25/2014
Numéro de la FDS: 100000009032 22 / 22 Styrene Monomer 10 - 15 PPM In-
hib
EGEST EOSCA Generic Exposure
Scenario Tool
OSHA Occupational Safety & Health Admin-
istration
EOSCA European Oilfield Specialty
Chemicals Association
PEL Permissible Exposure Limit
EINECS European Inventory of Exist-
ing Chemical Substances
PICCS Philipines Inventory of Commercial
Chemical Substances
MAK Germany Maximum Concen-
tration Values
PRNT Presumed Not Toxic
GHS Globally Harmonized System RCRA Resource Conservation Recovery Act
>= Greater Than or Equal To STEL Short-term Exposure Limit
IC50 Inhibition Concentration 50% SARA Superfund Amendments and Reau-
thorization Act.
IARC International Agency for Re-
search on Cancer
TLV Threshold Limit Value
IECSC Inventory of Existing Chemi-
cal Substances in China
TWA Time Weighted Average
ENCS Japan, Inventory of Existing
and New Chemical Substanc-
es
TSCA Toxic Substance Control Act
KECI Korea, Existing Chemical In-
ventory
UVCB Unknown or Variable Compositon,
Complex Reaction Products, and
Biological Materials
<= Less Than or Equal To WHMIS Workplace Hazardous Materials In-
formation System
LC50 Lethal Concentration 50%