rosetta earrings - creative beadcraft · rosetta earrings simple and fast to make earrings from...
TRANSCRIPT
Rosetta earringsSimple and fast to make earrings from Matubo 8/0s, 7/0s and Superduos
Material (for one pair of earrings):
Matubo 7/0 beads (16 pcs)Matubo 8/0 beads (40 pcs)Matubo Superduo beads (16 pcs)Miyuki Delica 11/0 (32 pcs)15/0 seed beads (16 pcs)Beading needle and thread (Nymo, Fireline)
Jump rings, earwiresOptional: 2 dropshaped beads, 2 headpins
Difficulty: for beginners
1 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) For personal use only. www.matubobeads.com
1) String two Superduos and three 8/0s. Repeat four times.
2) Slide all the beads to the end of the thread and tie a square knot to form a circle. Then pass through the upper hole of the nearest Superduo
3) Add one 7/0 and then pass through the upper hole of the next Superduo.
4) Add one 8/0. Skip the next 8/0 and pass through the second 8/0.
5) Add one 8/0 and pass through the upper hole of the next Superduo.
6) Repeat steps 3,4 and 5 ...
7) ... until you reach the end of the row.
8) Pass through the next 7/0 and Superduo.
9) Add one 15/0 and then pass through the next 8/0 bead from the previous row.
10) Add one 7/0 and pass through the next 8/0 bead from the previous row.
2 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) For personal use only. www.matubobeads.com
11) Add one 15/0 and pass through the upper hole of the next Superduo.
12) Repeat steps 8, 9, 10 and 11 ...
13) ... until you reach the end of the row.
14) Weave through beads to get to the first row. The thread should leave one of the 8/0s near the corner.
15) Add one Delica. Skip the two Superduos in the corner and pass through the next 8/0.
16) Add one Delica. Skip the gap between 8/0s and pass through the next 8/0 (as shown on the picture).
17) Repeat steps 15 and 16 ...
18) ... until you reach the end of the row. At the end of the row add one last Delica and then pass through the last 8/0 from the first row and then through the first Delica from this row.
19) Add one Delica and pass through the next Delica from the previous row
20) Repeat step 19 until you reach the end of the row
3 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) For personal use only. www.matubobeads.com
21) Tie a few halfhitch knots and cut off all the remaining thread
22) Make the second earring.Use jump rings to attach earwires.
Tips:• You can use 8/0s instead of 7/0s in step 3 (as
shown on the pink, blue and goldwhite earrings on this page)
• You can use a headpin and a jump ring to attach a dropshaped bead to the bottom of the earring
• You can make a lot of these components and connect them to make a bracelet or a necklace
4 | Design and tutorial by Nela Kábelová (www.gianelle.beadforum.cz) For personal use only. www.matubobeads.com