room relative humidity and relative humidity temperature relative humidity and relative humidity ...

Download Room Relative Humidity and Relative Humidity  Temperature   Relative Humidity and Relative Humidity  Temperature Sensor ... (85 mm x 63 mm x 38 mm) ... Room Relative Humidity and Relative Humidity  Temperature Sensor

Post on 12-May-2018

233 views

Category:

Documents

3 download

Embed Size (px)

TRANSCRIPT

  • Technical Specification Sheet

    Rev. 3, December, 2000

    Document No. 149-359P25

    Page 1 of 3

    Room Relative Humidity and Relative Humidity & Temperature Sensor

    Description

    The Room Relative Humidity and Relative Humidity & Temperature Sensors monitor and transmit standard signals for humidity and temperature that can be used with a variety of building control systems including the APOGEE Automation System. These units are especially suited for commercial HVAC control applications. Three models are available plain humidity sensing only, plain humidity and temperature sensing only, and humidity and temperature sensing in a full-featured version. All three models are available in either 5% accuracy, 2% accuracy, or 2% accuracy NIST (National Institute of Standards and Technology) certified versions.

    Both the standard 5% accuracy and 2% accuracy versions are calibrated using a NIST traceable calibration standard. The 2% accuracy NIST certified versions are also calibrated using a NIST traceable standard, however, an additional three-point humidity calibration check and one-point temperature calibration check is performed and documented on a calibration certificate included with the sensor.

    All units incorporate a bulk resistive polymer humidity-sensing element. The combination humidity and temperature units incorporate a 1K Ohm Platinum RTD temperature-sensing element.

    All units have a RJ-11 jack located on the bottom of the sensor where the EasyCal Plus Humidity Calibrator can be connected to check the operation of the humidity sensor and perform a one-point offset adjustment if necessary.

    Full-Featured Model

    The full-featured model offers a wide range of features and functionality that can be used with a variety of building control systems including the APOGEE Automation System. These features include:

    Liquid Crystal Display (LCD): A two-line alphanumeric LCD allows simultaneous display of room temperature and relative humidity in degrees F or C. Relative humidity can also be displayed alone.

    Digital temperature set point adjustment: The sensors keypad allows error-free digital temperature set point adjustments in one-degree increments. Set point values momentarily display as changes are made.

    Override button: The flush mounted override button allows an occupant to change to an occupied control schedule during the unoccupied cycle for a predetermined time period.

    Display of operating mode: Graphic symbols are displayed in the LCD to indicate the controllers operating mode. A sun indicates occupied mode operation and a moon indicates night mode operation.

  • Page 2 of 3 Siemens Building Technologies, Inc.

    Specifications - Humidity Element

    Operating range 0 to 100% RH

    Accuracy at 77F (25C) 5% or 2% RH over 20-95% RH including hysteresis, linearity, and repeatability

    Operating temperature 32 to 122F (0 to 50C)

    Temperature effect Less than 0.06% per degree F (0.11% per degree C)

    Output signal-RH only units 4-20 mA DC, 0-100% linear, proportional

    Output signal-RH/T units 0-10 Vdc, 0-100% linear, proportional

    Calibration requirements Annually (field calibration using the EasyCal Plus)

    Polarity Protection Yes

    Specifications Temperature Element (for combination humidity & temperature units only)

    Operating range 32 to 122F (0 to 50C) RTD Calibration Point 32F (0 C)

    Sensing Element 1K Platinum RTD

    Output Signal 0-10 Vdc, 32 to 122F (0 to 50C) linear, proportional Set point adjustment range 73F 10F (23C 10C) Calibration requirements None required

    General Specifications

    Installation 750 feet (229 m) max. cable length using 18 to 22 AWG twisted pair shielded cable (overall shielded cable for Full-Featured Units), NEC Class 2

    Connections Screw terminals

    Cover dimensions 3-11/32" H x 2-1/2" W x 1-1/2" D (85 mm x 63 mm x 38 mm)

    Color Desert beige or white

    Voltage requirement 18 to 35 Vdc

    Ordering Information

    Description Accuracy % Certification Features Product Part Number

    RH only 5 Plain Sensing 544-808

    RH only 2 Plain Sensing 544-811

    RH only 2 Included Plain Sensing 544-812

    RH/T 5 Plain Sensing 544-814

    RH/T 2 Plain Sensing 544-819

    RH/T 2 Included Plain Sensing 544-820

    RH/T 5 Full-Featured 544-818

    RH/T 2 Full-Featured 544-822

    RH/T 2 Included Full-Featured 544-823

    Add letter suffix to indicate desired color: A=Desert Beige; B=White (e.g., 544-808A for Desert Beige).

  • Information in this document is based on specifications believed correct at the time of publication. The right is reserved to make changes as design improvements are introduced. APOGEE is a trademark of Siemens Building Technologies, Inc. 2000 Siemens Building Technologies, Inc.

    Siemens Building Technologies, Inc. Landis Division 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513

    Printed in the U.S.A. (origin) Page 3 of 3

    Accessories Ordering Information

    Description Product Part Number

    EasyCal Plus Humidity Calibrator 538-897

    Single Adapter Base Kit (Beige) 544-782A

    Double Adapter Base Kit (White) 544-783B

    Double Adapter Base Kit (Beige) 544-783A

    Extender Ring Kit (White) 544-785B

    Extender Ring Kit (Beige) 544-785A

    Non-Conduit Rough-In Kit 544-784

    Sensor Power Supply Module (for MBC/RBC applications using the RH/T units) PTX6.4SPS

    AI Point Termination Module (for MBC/RBC applications using the RH/T units) PTM6.2U10

    AI Point Termination Modules (for MBC/RBC applications using the RH only units) PTM6.2I420

Recommended

View more >