rane sixty-four mixer manual - .• serato dj software manual. • this sixty-four mixer manual
Post on 06-Sep-2018
Embed Size (px)
RANE SIXTY-FOUR MIXER MANUAL
Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with a dry cloth.7. Do not block any ventilation openings. Install in accordance with manufacturers instructions.8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including
amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord and plug from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.
11. Only use attachments & accessories specified by Rane.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. The plug on the power cord is the AC mains disconnect device and must remain readily operable. To completely disconnect this apparatus from the AC mains, disconnect the power supply cord plug from the AC receptacle.
16. This apparatus shall be connected to a mains socket outlet with a protective earthing connection.17. When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in
each pole shall be incorporated in the electrical installation of the building.18. If rack-mounting, provide adequate ventilation. Equipment may be located above or below this
apparatus, but some equipment (like large power amplifiers) may cause an unacceptable amount of hum or may generate too much heat and degrade the performance of this apparatus.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
WarningTo reduce the risk of electrical shock, do not open the unit. No user serviceable parts inside. Refer servicing to qualified service personnel. The symbols shown below are internationally accepted symbols that warn of potential hazards with electrical products.
This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
This symbol indicates that a dangerous voltage constituting a risk of electric shock is present within this unit.
These stickers are located on the bottom of the mixer.
RISK OF ELECTRIC SHOCKDO NOT OPEN
FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Rane Corporation could void the users authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada.
Copyright Notices2013 Rane Corporation. All rights reserved. Serato DJ and Scratch Live are trademarks of Serato. Trademarked in the United States and other countries. This software is based in part on the work of the Independent JPEG Group, and uses libpng code, copyright 2000-2002 Glenn Randers-Pehrson. The Serato NoiseMap Control Tone, the audio pressed on Serato Control vinyl and Control CDs, is copyright 2004-2013 Serato. The Control Vinyl and Control CDs are licensed for personal use only. The creation of personal backups of the Control CD is allowed, however duplicating Control CDs for commercial benefit is strictly prohibited. For avoidance of doubt the duplication or creation of Control vinyl for any use is strictly prohibited. Please respect our copyright. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Apple, Mac, Macintosh, iTunes, Safari, QuickTime, GarageBand, and OS X are registered trademarks of Apple Inc., registered in the United States and other countries.
Check ListThese items are included in the box: 1 Sixty-Four Mixer. Serato DJ software and drivers install disc. 4 (four) control CDs. 4 (four) control records. 1 USB cable. IEC C5 line cord. Serato DJ Software Manual. This Sixty-Four Mixer Manual.
Wear PartsThe Sixty-Four Mixer contains no wear parts. The control vinyl records and CDs are wear parts as described in "Limited Warranties" on page 35.
2 Important Safety Instructions
5 Quick Start: Software
6 Quick Start: Hardware
9 Sixty-Four Overview
10 Sixty-Four Connections10 Power Supply10 Mixer Outputs10 Two USB Ports
11 Deck Input Channels
12 Headphone Cueing
13 Software Controls13 Control Assignment13 Library Scroll and Load13 Auto Looping Controls13 Slip13 Sync14 MIDI Triggers 1-814 MIDI Layers
15 Microphone Inputs
15 Main Mix
16 FlexFX Loop
17 Effects Engine17 FILTER Effect17 FLANGER Effect17 PHASER Effect18 ECHO Effect18 ROBOT Effect18 REVERB Effect18 Effects Display and BPM Source19 Effects Synchronization20 Effects Parameter Table
21 USB Audio
23 Shift Options23 Ext. Insert Options Menu23 Filter Effect Options Menu23 Flanger Effect Options Menu23 Echo Effect Options Menu24 Deck 1-4 Input Channel Options Menu24 Main Mix Options Menu24 Mixer Shift Functions24 MIDI Start/Stop24 Nudge24 BPM Adjust
25 DJ Swapping25 Deck Swapping Controls25 The DJ Handover Walkthrough25 Enhancing Back-to-Back Mixing with the USB Insert
26 Driver Control Panel26 ASIO (Windows)26 Core Audio (Macintosh)26 Preferences Screen27 Deck Inputs 1-4 Screen27 Effects Screen28 MIDI Configuration Screen
28 Factory Defaults
28 MIDI Mapping28 Mic Bypass Mode28 Top Panel Map29 Front Panel MIDI Controls30 Rear Panel MIDI30 Control Panel MIDI (Mixer Menu Controls)
32 Technical Specifications
33 Fader Maintenance
34 Declaration of Conformity
35 Limited Warranties
Quick Start: SoftwareBefore using your Sixty-Four, at least read this short section for the basics. Read the complete manual to get the best investment from your new Sixty-Four. This section will help get you started with one computer.
Serato DJ Software Installation for Mac OSXBefore installing, we recommend you check for a newer version of Serato DJ at serato.com/download and install the latest Serato DJ version if it is newer than the version on the CD-ROM that comes with your mixer.
1. Insert the Serato DJ Installer CD-ROM that came with your unit, -or- browse using Finder to the location where the Serato DJ download was saved.2. Double click the Serato DJ 1.5.dmg file.3. The software EULA screen will appear - read the License Agreement, then click Agree. 4. The disk image mounts and opens the actions folder, once this is finished you can unmount the disk
image and launch Serato DJ.5. Drag the Serato DJ application icon to the Applications folder alias.6. You may then need to enter your User Password to authenticate.7. Serato DJ will now copy to the Applications folder, once this is finished you can unmount the disk image
and launch Serato DJ.
Serato DJ Software Installation for WindowsBefore installing, we recommend you download and install the latest Serato DJ version from serato.com if it is newer than the version on the CD-ROM that comes with your mixer.
1. Insert the Serato DJ Installer CD-ROM that came with your unit, -or- browse using Windows Explorer to the location where the Serato DJ download installer was saved.2. Double click the file called SeratoDJ_1.5_installer.exe.3. Accept the Security Warning and click Run.4. The installer introduction screen will appear, click Next.5. Read the License Agreement, then tick I agree to the license terms and conditions, then c