quick start guide fw-d2016np d4016np - fujitsu quick start guide (japanese, english) … 1 each...

2
SERVIS TM IP-KVM FW-D2016NP / FW-D4016NP Quick Start Guide NC14013-0923RS-02 <Inquiry about our products> FUJITSU COMPONENT LIMITED Marketing Group TEL: 81-3-5449-7006 E-mail: [email protected] URL: http://www.fcl.fujitsu.com/en/ Check that the following items are contained in the packaging. - The device - Power cables 3 pin plug-IEC320 socket (AC100V)…1 IEC320 plug-IEC320 (AC200V)…1 - Serial Cable … 1 - Flanges … 2 - Screws for flange …4 - CD-ROM …1 Installer/User Guide FW-Client Software - Warranty certificate … 1 * This warranty is valid in Japan. - License information … 1 - China RoHS guide …1 - Quick Start Guide (Japanese, English) … 1 each Step2 Connecting the Device Introduction 1. Connect the device as shown below. 2. When you have connected the device, turn on each connected server first, and then the device. 3. The following dialog box appears. Click [Next]. 3. The following Setup window appears. Click [Network]. 4. The following Network window appears. Specify the IP address here. 4. On the following dialog box, if you agree with the statement, select the corresponding option, and click [Next]. - Thank you for purchasing this product. This "Quick Start Guide" describes the items contained in the packaging, and explains the initial setup and procedures for basic operations. Make sure to read this manual when using the device. - Read the "Safety Precautions" in the CD-ROM provided with the device in advance for its correct use. The "Safety Precautions" includes indications to obviate any chance of accident or damage to you and people near you, and your property. - For details on operations, refer to the Installer/User Guide provided with the device. Ethernet Power Source Local Connection Remote User Modem Telephone Network FW-D2016NP / FW-D4016NP Server Server Server Server 5. The contents of the dialog box are shown as below. Select the install destination, and click [Next]. 6. The contents of the dialog box are shown as below. To set an icon on the desktop, select the check box and click [Install]. 6. The following message appears, and the device restarts. If the [Free] tag is shown 1 minute later, the network setup is complete. 5. When you specify a fixed IPv4 address, click the "Static" and the "IPv4" radio button, enter values in the IP address, Netmask and Gateway fields, and click the [OK] button. (For DHCP, select the corresponding Opion.) Step 1 Checking the Components 7. The following dialog box appears. Click [YES]. 8. The following dialog box is shown, and installation starts. Step3 Setting Up the Network For the initial settings of the device, set the IP address by a local operation. 1. The device starts operating about 1 minute after it is turned on, and the [Free] tag appears in the monitor for local connection. 2. Press the [PrintScreen] key on the local keyboard once, then the following Main window appears. Click [Setup]. Step4 Installing FW-Client 9. When the contents of the dialog box are shown as below, the installation is complete. Click [Done]. By using the device, install "FW-Client" – a tool for managing the target device – into the remote client’s PC. The following explains how to install into a Windows computer. 2. The following dialog box appears. Click [OK]. 1. Launch Setup.exe, contained in the CD-ROM provided with the device. (Continued to the reverse side)

Upload: lamlien

Post on 04-Sep-2018

230 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Quick Start Guide FW-D2016NP D4016NP - Fujitsu Quick Start Guide (Japanese, English) … 1 each Introduction Step2 Connecting the Device 1. Connect the device as shown below. When

SERVISTM IP-KVM FW-D2016NP / FW-D4016NP Quick Start Guide

NC14013-0923RS-02 <Inquiry about our products> FUJITSU COMPONENT LIMITED Marketing Group TEL: 81-3-5449-7006 E-mail: [email protected] URL: http://www.fcl.fujitsu.com/en/

Check that the following items are contained in the packaging. - The device - Power cables

3 pin plug-IEC320 socket (AC100V)…1 IEC320 plug-IEC320 (AC200V)…1

- Serial Cable … 1 - Flanges … 2 - Screws for flange …4 - CD-ROM …1

Installer/User Guide FW-Client Software

- Warranty certificate … 1

* This warranty is valid in Japan. - License information … 1 - China RoHS guide …1 - Quick Start Guide

(Japanese, English) … 1 each

Step2 Connecting the Device Introduction 1. Connect the device as shown below.

2. When you have connected the device, turn on each connected server first, and then the device.

3. The following dialog box appears. Click [Next].

3. The following Setup window appears. Click [Network].

4. The following Network window appears. Specify the IP address here.

4. On the following dialog box, if you agree with the statement, select the corresponding option, and click [Next].

- Thank you for purchasing this product. This "Quick Start Guide" describes the items contained in the packaging, and explains the initial setup and procedures for basic operations. Make sure to read this manual when using the device.

- Read the "Safety Precautions" in the CD-ROM provided with the device in advance for its correct use. The "Safety Precautions" includes indications to obviate any chance of accident or damage to you and people near you, and your property.

- For details on operations, refer to the Installer/User Guide provided with the device.

Ethernet

Power Source

Local Connection

Remote User

Modem Telephone Network

FW-D2016NP / FW-D4016NP

Server Server

Server Server

5. The contents of the dialog box are shown as below. Select the install destination, and click [Next].

6. The contents of the dialog box are shown as below. To set an icon on the desktop, select the check box and click [Install].

6. The following message appears, and the device restarts. If the [Free] tag is shown 1 minute later, the network setup is complete.

5. When you specify a fixed IPv4 address, click the "Static" and the "IPv4" radio button, enter values in the IP address, Netmask and Gateway fields, and click the [OK] button. (For DHCP, select the corresponding Opion.)

Step 1 Checking the Components

7. The following dialog box appears. Click [YES].

8. The following dialog box is shown, and installation starts.

Step3 Setting Up the Network

For the initial settings of the device, set the IP address by a local operation.

1. The device starts operating about 1 minute after it is turned on, and the [Free] tag appears in the monitor for local connection.

2. Press the [PrintScreen] key on the local keyboard once, then the following Main window appears. Click [Setup].

Step4 Installing FW-Client 9. When the contents of the

dialog box are shown as below, the installation is complete. Click [Done].

By using the device, install "FW-Client" – a tool for managing the target device – into the remote client’s PC. The following explains how to install into a Windows computer.

2. The following dialog box appears. Click [OK].

1. Launch Setup.exe, contained in the CD-ROM provided with the device.

(Continued to the reverse side)

Page 2: Quick Start Guide FW-D2016NP D4016NP - Fujitsu Quick Start Guide (Japanese, English) … 1 each Introduction Step2 Connecting the Device 1. Connect the device as shown below. When

(Continued from the front page)

NC14013-0923RS-02 <Inquiry about our products> FUJITSU COMPONENT LIMITED Marketing Group TEL: 81-3-5449-7006 E-mail: [email protected] URL: http://www.fcl.fujitsu.com/en/

Step5 Setting Up FW-Client

4. The contents of the dialog box are shown as below, and data is retrieved from the device.

3. The following [Video Session Viewer] window appears, and target device operations are enabled.

3. On the following dialog box, select the required check box(es), and click [Next].

8. The contents of the dialog box are shown as below, and the registration of the device is completed.

7. The contents of the dialog box are shown as below. Search for the device from the network.

Set up for operating the device and other target devices from FW-Client.

2. The following window appears. To register the device, click [New Appliance].

1. Select [Start]→[Programs] → [Fujitsu Component Limited FW Client]. Or, double-click the [Fujitsu Component Limited FW Client] icon.

9. The device is added to the appliance list as shown below.

5. The updated information is shown. The dialog box below shows that a new server module has been detected. Click [Next].

6. The contents of the dialog box are shown as below, and the update is completed.

To finish, click [X] on the top right of the Video Session Viewer window.

3. The following [New Appliance Wizard] dialog box appears. Click [Next].

4. Choose the product type. Select [Other], and click [Next].

1. Click the [Servers] tab on the FW-Client window, select and double-click the server module detected and registered at Step6.

2. The following login dialog box appears. Enter the Username and password. By default, "admin" is registered both for the Username and the Password. After entering, click [OK].

You need to install the version after 1.6 of JAVA Runtime Environment (JRE) in the remote client PC to operate the target device. Since JRE is stored in attached CD-ROM, please use it.

Perform an operation on a connected target device.

Step7 Access a Target Device

NOTES

Adjusting the mouse pointer speed on the server

When a remote user accesses a target server to perform an operation, the mouse cursors on the remote user side and target server side may not coincide. When this happens, adjust the mouse pointer setting for the operating system on the target server so that the two mouse cursors coincide.

Setup for Windows XP, Server 2003, Vista

-Click [Control Panel] → [Mouse] to show [Mouse Properties].

-Click the [Pointer Options] tab.

-In the [Select a pointer speed] section, move the slider to the middle. Clear the [Enhance pointer precision] check box.

-In the [Snap To] section, clear the [Automatically move pointer to the default button in a dialog box] check box.

-Click the [OK] button to finish.

Step6 Running an Update

Check the current connection status of a server module by re-synchronizing FW-Client and the device.6. Enter the IP address of the

device. Then click [Next].

5. Confirm the IP address setting. If you have set up an IP address for the device at Step 3, Select [Yes, the Appliance has an IP address], and click [Next].

1. Click the device registered in the appliance list, and click [Resync] shown at the bottom.

2. The [Resync Appliance Wizard] dialog box appears. Click [Next].

For software setup or details on operations, refer to the Installer/User Guide in the CD-ROM provided with the device.