questionnaire primary flow elements

2
11/2013 Page 1 of 2 Flow measurement Questionnaire Primary flow elements Customer data Company Name Department Address Date Phone Mobile Fax E-mail Purchase order or project Tag no. Application Medium Single-phase Multi-phase Liquid Gas Steam Gas/liquid ratio (in %): Volume Mass Density (at operating conditions): kg/m³ lb/ft³ Viscosity: cP cST MW: Cp/cv: Relative humidity: Compressibility factor: Viscosity: cP cST Superheated Saturated, dry Saturated, wet (water content 0 ... 5 %) % Minimum Normal Maximum Full scale Units Flow rate Pressure barg psig mmH 2 Og Temperature °C °F Nominal size Schedule Nominal pressure rating Material Sealing face: Raised face (RF) Flat face (FF) Ring-type joint (RTJ) Differential pressure at full scale bar psi mmH 2 O Commercial information Medium characteristics Process data Pipeline and piping class Design data Competitors for this project Target price $

Upload: truongkiet

Post on 31-Dec-2016

221 views

Category:

Documents


0 download

TRANSCRIPT

11/2013 Page 1 of 2

Flow measurement

QuestionnairePrimary flow elements

Customer data

CompanyName

DepartmentAddress

DatePhoneMobile

FaxE-mail

Purchase order or projectTag no.

Application

Medium

Single-phase Multi-phase

Liquid

Gas

Steam

Gas/liquid ratio (in %): Volume Mass

Density (at operating conditions): kg/m³ lb/ft³Viscosity: cP cST

MW: Cp/cv: Relative humidity:Compressibility factor: Viscosity: cP cST

Superheated Saturated, dry Saturated, wet (water content 0 ... 5 %) %

Minimum Normal Maximum Full scale UnitsFlow ratePressure barg psig mmH2OgTemperature °C °F

Nominal size Schedule Nominal pressure rating MaterialSealing face: Raised face (RF) Flat face (FF) Ring-type joint (RTJ)

Differential pressure at full scale bar psi mmH2O

Commercial information

Medium characteristics

Process data

Pipeline and piping class

Design data

Competitors for this project

Target price € $

WIKA Alexander Wiegand SE & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyTel. +49 9372 132-0Fax +49 9372 [email protected]

Page 2 of 211/2013

Pressure taps: Flange taps Corner taps Radius taps Amount:

Tappings: ½" NPT ½" SW Other:Material of nuts and studs:

Pressure taps: Corner taps Flange tapsTappings: ½" NPT ½" SW Other:Material: Stainless steel 316/316L Other:End connection: Butt welded Flanged 1)

Design: ISA 1932 Long radiusTappings: ½" NPT ½" SW Other:

Number of pressure taps:

Material: Stainless steel 316/316L Other:Mounting option, ISA 1932: With flanges Without flangesMounting option, Long radius: Butt welded Flanged 1)

Design: From bar Welded sheetMaterial: Stainless steel 316/316L Carbon steel Other:

Exit cone: 7° 15° Other: Truncated

Tappings: ½" NPT ½" SW Other:

Flanged Dimensions:

Number of pressure taps:End connection: Butt welded Flanged 1)

Mounting types: Compression fitting Flanged version Extractable versionVariants (series): 73 75 78

End support: No Yes

Design: Square edge Quarter circle Eccentric Conical entranceMaterial: Stainless steel 316/316L Other:Drain hole, vent hole: None Drain hole Vent hole Hole dimension:

Orifice flange Orifice assembly (orifice plate and orifice flange)

Flow nozzle

Meter run Integral orifice

Pitot tube (FloTec)

Venturi tube

Orifice plate

Model of primary flow element

1) Flange rating and sealing face see “Pipeline and piping class” (page 1)