piping inspector - training.cutechgroup.comtraining.cutechgroup.com/admin/cutechgroup_upload/pdf/api...

CONTACT US [email protected]

+65 62626614/ 41 +65 97583097

PIPING INSPECTOR FUNDAMENTAL PIPING DESIGN THAT EMPHASIZES THE API SYLLABUS & RELEVANT EXAMINABLE CODE SECTIONS.

CLARIFY BASIC INTENTIONS OF ALL CODE SECTIONS, INTEPRET CODE RULINGS & MAKE COST EFFECTIVE 3R DECISIONS.

FOR ALL INSPECTORS, QA/QC ENGINEERS & PLANT MAINTENANCE PERSONNEL CONCERNED WITH PLANT INTEGRITY,

ENGINEERING CONSULTANTS & CONTRACTORS SUPPORTNG REFINERIES’ SHUT-DOWN INSPECTION, MAINTENANCE,

REPAIRS & UPGRADES WILL ALSO BENEFIT FROM THE API 570.

Singaporeans & SPRs enjoy IMMEDIATE $900 FUNDING SUPPORT

Course Seminar Fee

API 570 2000 SGD + 7% GST

(Course Materials & Standard Codes)

* TOP UP REQUIRED FOR API EXAMINATION

GROW YOUR CAREER WITH US, JOIN NOW

PART TIME & FULL TIME AVAILABLE

www.training.cutechgroup.com Quality Solutions Provider

NTUC members enjoy 50% unfunded course fee support* *capped at $250

LOCATION PIONEER JUNCTION #03-19 3 SOON LEE STREET SINGAPORE(627606)

Fee Details:

Seminar & Exam Fee

Foreigner Locals (Post-Funding)

SGD 2950 + GST

SGD 2200 + GST

All NTUC members can use UTAP to claim $250

Brief: Expect to learn about MAWP, Flange ratings, Retirement thickness for pipes, fittings and valves & choosing appropriate inspection tools & intervals.

Introduction to different ways of evaluations and decision making & familiarization of degradation mechanisms. ‘Know-how’s on repairs, alterations and rerating of piping systems & assessment of future remaining life, life extension methods for piping systems.

Modules:

1 Scope, definitions and organization of API 570 11 Inspection and testing practices of API 570

2 Repairs, alterations & re-rating of piping system 12 Inspection of buried piping

3 Frequency and extent of inspection, data evaluation 13 Detail discussions on material corrosion and degradation (API 571)

4 Various preventive actions against degradation 14 Piping component design, allowable stress values, of ASME B31.3

5 Case studies of wall thickness calculations, blank thickness calculations, test pressure, expansion margins

15 Material selection, impact test requirement and PWHT requirement of ASME B 31.3

6 Understanding and rating calculations of ASME B16.5 16 Case studies of Impact testing results, requirement of pre-heating and PWHT

7 Introduction to ASME Sec IX and its various provisions 17 Welding procedure qualification & welder qualification, Case studies of checking of PQR, WPS

8 Discussions on API RP 577, welding inspection 18 Understanding the difference between Inspection and Examination

9 Various NDE proposed to detect flaws in metals 19 Understanding rules imposed by ASME Sec V for various NDE techniques

10 Discussions on PMI (API RP 578) & API RP 574


Training Duration: 60 hours Examination: 7 hours Open Book 4 hours Closed Book 3 hours




+65 62626614/ 41 +65 97583097

PRESSURE VESSEL INSPECTORFUNDAMENTAL PRESSURE VESSEL DESIGN

FOR ALL PRESSURE VESSEL INSPECTORS, MANAGERS, PLANT OPERATIONS QA/QC,

MAINTENANCE ENGINEERS, MANAGERS & TECHNICIANS


REACH QUALITY RANKS WITH ADVANCED INSPECTIONS

Preparatory Course Seminar Fee

API 510 SGD 2000 + 7% GST


*TOP UP REQUIRED FOR EXAMIINATIONS

LOCATION PIONEER JUNCTION #03-19 3 SOON LEE STREET SINGAPORE (627606)

Fee Details:

Brief: Expect to learn about Basic Pressure Vessel Design engineering i.e. ASME Sec VIII Div.1, In-service inspection techniques (API 510/ 572 / 576 / 577), and In-service degradation mechanisms (API 571).

Review main concepts and technical terms of API 510 Inspection Code & understand basic design and rules for correct fabrication, inspection and testing of Pressure Vessels.

Seminar & Exam Fee


SGD 2950 + GST

SGD 2200 + GST

Modules:

1 Concepts related to new Vessels, ASME Sec. VIII. 20 Welding Inspection and Metallurgy (API RP 577)

2 Design of Cylindrical shells, 21 Introduction to API 510 Certification & Guidelines

3 Design of Dished heads - Hemispherical, Ellipsoidal, Tori-spherical

22 Calculation of vessel MAWP Static head calculations

4 Impact testing requirements 23 Calculate MAWP given vessel parts & elevations

5 Writing hydro test Procedure & pneumatic test procedure 24 How to conduct and certify Pressure tests

6 Inspection requirements for Pressure Vessels 25 Key concepts of Nozzle reinforcement

7 Fabrication and Heat treatment requirements 26 NDT of Pressure Vessels

8 Testing practices for In-Service Vessels as per API 510 27 Concepts related to Inspection of in-service Vessels

9 Monitoring degradation mechanisms 28 Typical degradation mechanisms in Pressure vessels

10 Inspection Plans 29 Pressure vessel inspection External & Internal

11 On-stream Inspection 30 Inspection and testing of Pressure relieving devices

12 Corrosion Rate Determination 31 Remaining Life Calculations

13 Frequency and Time of Inspection 32 Evaluation of Locally Thinned Areas

14 Evaluation of Pitted surface 33 Correction of Weld joint

15 Efficiency, Repairs, alterations & rerating of Pressure Vessels

34 Reports and Records & Sample Inspection Record

16 Discussions on Damage Mechanisms (API 571) 35 Introduction to ASME Sec IX & requirements

17 Understanding of PQR and WPS 36 Welding procedure qualification & welder qualification

18 ASME Sec V regulations for various NDE techniques 37 Inspection of pressure relief devices (API RP 576)

19 Safety valves, Relief valves, Safety Relief valves, Balanced Safety Relief valves

38 Inspection & Test Procedures of pressure relief devices

ENHANCE YOUR CAREER WITH US


Training Duration: 60 hours

Examination: 7 hours

Open Book 4 Hours

Closed Book 3 hours


+65 62626614/ 41 +65 97583097

ABOVE GROUND STORAGE TANK INSPECTOR FUNDAMENTAL STORAGE TANK DESIGN ENGINEERING

FOR ALL TANK INSPECTORS, PLANT OPERATIONS &

MAINTENANCE PERSONNEL, CORROSION & DESIGN ENGINEERS

INVOLVED WITH INTEGRITY ASSESSMENT OF IN-SERVICE TANKS.

PERSONS SUPPORTING REPAIRS, REPLACEMENT & PREVENTIVE

MAINTENANCE WILL ALSO BENEFIT FROM THE API 653.



Course Seminar Fee

API 653 2000 SGD + 7% GST


* TOP UP REQUIRED FOR EXAMIINATIONS



LOCATION PIONEER JUNCTION #03-19 3 SOON LEE STREET SINGAPORE (627606)

Fee Details:

Brief:

Expect to learn about Basic Storage tank design engineering (API 650), In-service inspection techniques (API 653/ RP 575/ RP 577), In-service degradation mechanisms (API 571), Cathodic protection (API RP 651) & Lining of tank bottom (API RP 652)

Review main concepts and technical terms of API 510 Inspection Code & understand basic design and rules for correct fabrication, inspection and testing of Pressure Vessels.

Modules:

1 Fundamentals of Storage Tank Design & construction (API 650)

15 Allowable stress values

2 Shell design, roof design, bottom Design 16 Material selection

3 Impact test requirement of API 650 & impact test results 17 Shell thickness calculations: bottom plate thickness, roof plates, nozzle openings

4 API 650 Requirements for Tank fabrication, erection, NDT and Leak testing

18 Scope, Definitions and organisation of API 653 Inspection Intervals

5 Data evaluation and corrosion assessment of Roof, Shell & bottom

19 Estimation of corrosion rate, Inspection and testing practices of API 653

6 Evaluation for brittle failure 20 Various preventive actions against degradation

7 Frequency and extent of inspection, data evaluation 21 Repairs, alterations, reconstruction, relocation & re-erection of storage tanks

8 Replacement of tank bottom 22 Hot tapping on tank shell

9 Detail discussions on material corrosion and degradation (API 571)

23 NDT of tank repairs, leak testing. Evaluation of bottom settlement

10 Storage tank Inspection (study of other codes and standards)

24 Discussions on cathodic protection methods against soil corrosion (API RP 651)

11 Recommended practices for inspection of storage tanks (API RP 575)

25 Discussions on Lining of bottoms of storage tanks (API RP 652)

12 Introduction to ASME Sec IX and its various provisions 26 Welding procedure qualification & welder qualification

13 Case studies of checking of PQR & WPS 27 Discussions on Corrosion Protection & Quality of Welding & API RP 577 Welding Inspection

14 Discussions on Lining of bottoms of storage tanks (API RP 652)

28 Various NDE methods to detect flaws in metals

15 Understanding rules imposed by ASME Sec V for various NDE techniques

Seminar & Exam Fee


SGD 2950 + GST

SGD 2200 + GST





Open Book 4 Hours

Closed Book 3 hours


62626614/ 41 97583097


REFRACTORY PERSONNEL FUNDAMENTAL REFRACTORY INSTALLATION & QUALITY CONTROL METHODS

REFRACTORY PERSONNEL IN PETROCLEUM, PETROCHEMICAL & CHEMICAL

INDUSTRIES CONCERNED WITH INSTALLATION, INSOECTION, TESTING AND

REPAIR OF REFRACTORY SYSTEMS.


Course Seminar & Exam Fee

API 936 2400 SGD + 7% GST



LOCATION PIONEER JUNCTION #03-19 3 SOON LEE STREET S(627606)

LOCATION PIONEER JUNCTION #03-19 3 SOON LEE STREET S(627606)

Brief:

Candidates can expect to learn about Refractory materials & their properties, Laboratory Testing Procedures,

Installation, Quality Control, Post-installation Inspection and Acceptance of the Refractory Lining as per usage in

Refineries, Power generation stations, Petrochemical facilities and chemical industries & referenced standards like ACI

and ASTM.

Design, installation, inspection, and repair of refractory systems in Pressure vessels, Exchangers, Piping, Boilers, and

Fired equipment will also be covered.

Modules:

1 What are Refractories, Various refractory materials 13 Technical terms and definitions, API 936 Overview

2 Desirable properties of refractory materials 14 Laboratory Testing Procedures, Material Qualification

3 Test methods and related calculations 15 Testing equipment, sample preparation techniques, test specimens

4 Refractory Installation methods (e.g. gunning, casting, ramming, and hand packing)

16 Sampling and sample preparation procedures

5 Procedures for determining optimal water content and mixing

17 Environmental factors (minimum and maximum temperatures)

6 Surface preparation and cleanliness requirements 18 Anchor: welding, layouts, patterns, materials

7 Frequency and methods of production sampling: gunning, casting, hand packing

19 Water addition: quantity and temperature, mixing procedures

8 Gunite procedures and equipment 20 Casting procedures and equipment (e.g. air vibrator, vibrator frequency, vibrator sizing, forming, setup)

9 Ramming/Hand packed procedures and equipment 21 Visual and non-destructive test methods and qualification testing methods

10 Application/limitation for various inspection techniques 22 Curing and dry out procedures

11 Placement of temperature sensing probes 23 Recommended heat up and cool down schedules

12 Lining integrity inspection techniques




Closed Book

www.training.cutechgroup.com Quality Solutions Provider www.training.cutechgroup.com Quality Solutions Provider

piping inspector - training.cutechgroup.comtraining.cutechgroup.com/admin/cutechgroup_upload/pdf/api...

Documents