panasonic tc-p50g20 tc-p50g25 chassis gpf13du

5/25/2018 Panasonic Tc-p50g20 Tc-p50g25 Chassis Gpf13du

1/119

Panasonic Corporation 2010.

Unauthorized copying and distribution is a violation

of law.

ORDER NO.MTNC100212CE

B34 Canada: B62

50 inch Class 1080p Plasma HDTVModel No. TC-P50G20

TC-P50G25GPF13DU Chassis


2/119

2

TABLE OF CONTENTSPAGE PAGE

1 Safety Precautions-----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

2 Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatically Sensitive (ES) Devices ----------4

2.2. About lead free solder (PbF) ----------------------------5

3 Service Navigation------------------------------------------------6

3.1. Service Hint--------------------------------------------------6

3.2. Applicable signals------------------------------------------7

4 Specifications ------------------------------------------------------8

5 Service Mode -------------------------------------------------------9

5.1. How to enter into Service Mode ------------------------9

5.2. Option - Mirror--------------------------------------------- 11

5.3. Service tool mode---------------------------------------- 11

5.4. Hotel mode------------------------------------------------- 12

5.5. Data Copy by SD Card ---------------------------------13

6 Troubleshooting Guide---------------------------------------- 16

6.1. Check of the IIC bus lines------------------------------ 16

6.2. Power LED Blinking timing chart --------------------- 17

6.3. No Power--------------------------------------------------- 18

6.4. No Picture -------------------------------------------------- 196.5. Local screen failure -------------------------------------- 20

7 Service Fixture & Tools--------------------------------------- 21

7.1. SC jig --------------------------------------------------------21

8 Disassembly and Assembly Instructions--------------- 22

8.1. Remove the Rear cover -------------------------------- 22

8.2. Remove the AC inlet ------------------------------------22

8.3. Remove the P-Board------------------------------------ 22

8.4. Remove the Side terminal cover and Side

shield metal ------------------------------------------------ 22

8.5. Remove the Tuner unit --------------------------------- 23

8.6. Remove the A-Board------------------------------------ 23

8.7. Remove the Speakers ----------------------------------23

8.8. Remove the SU-Board---------------------------------- 238.9. Remove the SD-Board---------------------------------- 23

8.10. Remove the SC-Board---------------------------------- 24

8.11. Remove the SS2-Board -------------------------------- 24

8.12. Remove the SS-Board---------------------------------- 24

8.13. Remove the Hanger metals and the One leg

bracket ------------------------------------------------------24

8.14. Remove the Cabinet mount metals------------------ 25

8.15. Remove the C1-Board ----------------------------------25



8.18. Remove the Plasma panel section from the

Cabinet assy----------------------------------------------- 26

8.19. Remove the Contact metals--------------------------- 26

8.20. Remove the K-Board------------------------------------ 26

8.21. Replace the plasma panel ----------------------------- 27

9 Measurements and Adjustments-------------------------- 28

9.1. Adjustment ------------------------------------------------- 28

10 Block Diagram--------------------------------------------------- 33

10.1. Main Block Diagram ------------------------------------- 33

10.2. Block (1/4) Diagram -------------------------------------34

10.3. Block (2/4) Diagram -------------------------------------35

10.4. Block (3/4) Diagram -------------------------------------36

10.5. Block (4/4) Diagram -------------------------------------37

11 Wiring Connection Diagram--------------------------------- 39

11.1. Caution statement. -------------------------------------- 39

11.2. Wiring (1) -------------------------------------------------- 39

11.3. Wiring (2) -------------------------------------------------- 40

11.4. Wiring (3) -------------------------------------------------- 41

12 Schematic Diagram-------------------------------------------- 43

12.1. Schematic Diagram Note ------------------------------ 43

12.2. P-Board (1/3) Schematic Diagram ------------------ 44



12.5. A-Board (1/18) Schematic Diagram----------------- 47









12.14. A-Board (10/18) and K-Board Schematic

Diagram ---------------------------------------------------- 56

12.15. A-Board (11/18) Schematic Diagram --------------- 5712.16. A-Board (12/18) Schematic Diagram--------------- 58

12.17. A-Board (13/18) Schematic Diagram--------------- 59






12.23. C1-Board Schematic Diagram ----------------------- 65

12.24. C2-Board (1/2) Schematic Diagram ---------------- 66




12.28. SC-Board (1/4) Schematic Diagram ---------------- 7012.29. SC-Board (2/4) Schematic Diagram ---------------- 71

12.30. SC-Board (3/4) Schematic Diagram ---------------- 72

12.31. SC-Board (4/4) Schematic Diagram ---------------- 73

12.32. SS-Board (1/2) Schematic Diagram ---------------- 74

12.33. SS-Board (2/2) and SS2-Board Schematic

Diagram ---------------------------------------------------- 75

13 Printed Circuit Board------------------------------------------ 76

13.1. P-Board ---------------------------------------------------- 76

13.2. K and SS2-Board ---------------------------------------- 79

13.3. A-Board ---------------------------------------------------- 80

13.4. C1-Board--------------------------------------------------- 82

13.5. C2-Board--------------------------------------------------- 83

13.6. C3-Board--------------------------------------------------- 84

13.7. SC-Board -------------------------------------------------- 85

13.8. SS-Board -------------------------------------------------- 87

14 Exploded View and Replacement Parts List----------- 89

14.1. Exploded View and Mechanical Replacement

Parts List--------------------------------------------------- 89

14.2. Electrical Replacement Parts List ------------------- 95


3/1193

1 Safety Precautions

1.1. General Guidelines1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the

wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.

3. When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug them straight

out.

4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.1.1. Leakage Current Cold Check1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed metal-

lic cabinet part on the equipment such as screwheads,

connectors, control shafts, etc. When the exposed metal-lic part has a return path to the chassis, the reading

should be between 1Mohm and 5.2Mohm.

When the exposed metal does not have a return path to

the chassis, the reading must be .

1.1.2. Leakage Current Hot Check (See

Figure 1.)1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel with a

0.15F capacitors, between each exposed metallic part

on the set and a good earth ground such as a water pipe,as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or more sensi-

tivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.75 volts

RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage

current must not exceed 1/2 milliamp. In case a measure-

ment is outside of the limits specified, there is a possibilityof a shock hazard, and the equipment should be repaired

and rechecked before it is returned to the customer.

Figure 1
http://-/?-http://-/?-http://-/?-http://-/?-


4/1194

2 Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damage

caused by electrostatic discharge (ESD).1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CautionBe sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-

ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient

to damage an ES device).


5/1195

2.2. About lead free solder (PbF)Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in its manufacture due to environmental conservation issues. For service and repair work, wed

suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbFstamped on the back of PCB.

Caution Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 F (30~40 C) higher. Please

use a high temperature soldering iron and set it to 700 20 F (370 10 C).

Pb free solder will tend to splash when heated too high (about 1100 F or 600 C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-

der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the

opposite side. (see figure below)

Suggested Pb free solderThere are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-

ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.


6/1196

3 Service Navigation

3.1. Service Hint

Board Name Function Board Name Function

P Power Supply C1 Data Driver (Lower Right)

C2 Data Driver (Lower Center)

A DC-DC Converter, Tuner

Speaker out, AV Terminal, HDMI in, SD Card

Digital Signal Processor, PEAKS-LDA2

Format Converter, Plasma AI, Sub-Field Processor

Power Switch, Key Switch

C3 Data Driver (Lower Left)

SC Scan Drive

SS Sustain Drive

SS2 Sustain out (Lower)

SU Scan out (Upper)

Non serviceable.

SU-Board should be exchanged for service.

SD Scan out (Lower)

Non serviceable.

SD-Board should be exchanged for service.

K Remote receiver, Power LED, C.A.T.S sensor


7/1197

3.2. Applicable signals* Mark: Applicable input signal for Component (Y, PB, PR), HDMI and PC

Note Signals other than those shown above may not be displayed properly.

The above signals are reformatted for optimal viewing on your display.

horizontal frequency (kHz) vertical frequency (Hz) COMPONENT HDMI PC

525 (480) / 60i 15.73 59.94 * *

525 (480) /60p 31.47 59.94 * *

750 (720) /60p 45.00 59.94 * *

1,125 (1,080) /60i 33.75 59.94 * *

1,125 (1,080) /60p 67.43 59.94 *1,125 (1,080) /60p 67.50 60.00 *

1,125 (1,080) /24p 26.97 23.98 *

1,125 (1,080) /24p 27.00 24.00 *

640 400 @70 31.47 70.08 *

640 480 @60 31.47 59.94 *

Macintosh13 inch (640 480) 35.00 66.67 *

640 480 @75 37.50 75.00 *

852 480 @60 31.44 59.89 *

800 600 @60 37.88 60.32 *

800 600 @75 46.88 75.00 *

800 600 @85 53.67 85.08 *

Macintosh16 inch (832 624) 49.73 74.55 *

1,024 768 @60 48.36 60.00 *

1,024 768 @70 56.48 70.07 *

1,024 768 @75 60.02 75.03 *

1,024 768 @85 68.68 85.00 *

Macintosh 21 inch (1,152 870) 68.68 75.06 *

1,280 768 @60 47.78 59.87 *

1,280 1,024 @60 63.98 60.02 *

1,366 768 @60 48.39 60.04 *


8/1198

4 Specifications

Power Source AC 120 V, 60 Hz

Power Consumption

Maximum 441 W

Standby condition 0.2 W

Plasma Display panel

Drive method AC type

Aspect Ratio 16:9

Visible screen size 50 inch class (49.9 inches measured diagonally)

(W H Diagonal) 43.5 inch 24.4 inch 49.9 inch (1,105 mm 622 mm 1,268 mm)

(No. of pixels) 2,073,600 (1,920 (W) 1,080 (H))[5,760 1,080 dots]

Sound

Audio Output 20 W [ 10 W + 10 W ] ( 10 % THD )

PC signals VGA, SVGA, XGA, WXGA, SXGA

Horizontal scanning frequency 31 - 69 kHz

Vertical scanning frequency 59 - 86 Hz

Channel Capability (Digital/Analog) VHF/ UHF: 2 - 69, CATV: 1 - 135

Operating Conditions

Temperature: 32 F - 104 F (0 C - 40 C)

Humidity: 20 % - 80 % RH (non-condensing)

Connection Terminals

VIDEO IN 1-2 VIDEO: RCA PIN Type 1 1.0 V [p-p] (75 )

AUDIO L-R: RCA PIN Type 2 0.5 V [rms]

COMPONENT IN 1-2 Y: 1.0 V [p-p] (including synchronization)

PB, PR: 0.35 V [p-p]

AUDIO L-R: RCA PIN Type 2 0.5 V [rms]

HDMI 1-3 TYPE A Connector 3

This TV supports [HDAVI Control 5] function.

USB 1-2 USB 2.0 Type A connector x 2

PC D-SUB 15PIN: R,G,B / 0.7 V [p-p] (75 )

HD, VD / 1.0 - 5.0 V [p-p] (high impedance)

LAN (for VIERA CAST IPTV) RJ45 (10BASE-T/100BASE-TX)

Card slot SD CARD slot 1

DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber Optic

FEATURES 3D Y/C FILTERCLOSED CAPTION V-Chip

IPTV (VIERA CAST) Media player

VIERA IMAGE VIEWER HDAVI Control 5

Dimensions (W H D)

Including pedestal 48.0 inch 31.9 inch 13.2 inch (1,218 mm 808 mm 335 mm)

TV Set only 48.0inch 30.3 inch 3.5 inch (1,218 mm 769 mm 88 mm)

Mass

Including pedestal 64.0 lb. (29.0 kg)

TV Set only 57.4 lb. (26.0 kg)

Note Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.


9/1199

5 Service Mode

5.1. How to enter into Service Mode

While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.

5.1.1. Key command[1] button...Main items Selection in forward direction

[2] button...Main items Selection in reverse direction

[3] button...Sub items Selection in forward direction

[4] button...Sub items Selection in reverse direction

[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )


10/11910

5.1.2. Contents of adjustment mode Value is shown as a hexadecimal number.

Preset value differs depending on models.

After entering the adjustment mode, take note of the value in each item before starting adjustment.

5.1.3. How to exitSwitch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.

Main item Sub item Sample Data Remark

ADJUST CONTRAST 46

COLOR 00

TINT 00SUB-BRT 000

WB-ADJ R-CUT 80

G-CUT 80

B-CUT 80

R-DRV FD

G-DRV FB

B-DRV FF

ALL-CUT 80

ALL-DRV FF

OPTION BOOT ROM Factory Preset

STBY-SET - -

EMERGENCY ON

CLK MODE ON

CLOCK FFF

EDID-CLK HIGH

MIRROR 00 (See next)

VSUS

AGING ALL WHITE Built-in test patterns can be

displayed.AI ALL BLUE + WHITE FLAME

AI ALL GREEN

AI ALL RED

LOW STEP WHITE

LOW STEP BLUE

LOW STEP GREEN

LOW STEP RED

RAMP WHITE

RAMP RED

RAMP GREEN

RAMP BLUE

A-ZONE B-ZONE

1% WINDOW

COLOR BAR

9 POINT BRIGHTNESS

WHITE FLAME

AI ALL BLUE

TWICE FIXATION 1% WINDOW

SCROLL

ON/OFF OR RGBW

R/G/B/W AGING MODE

0.5 TIME FIXATION ALL WHITE

ALL WHITE WITH COUNTSRV-TOOL - See next


11/11911

5.2. Option - MirrorPicture can be reversed left and right or up and down.

00 : Default (Normal picture is displayed)

01 : Picture is reversed left and right.

02 : Picture is reversed up and down.

Hint : If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in

A-board.

5.3. Service tool mode

5.3.1. How to access1. Select [SRV-TOOL] in Service Mode.

2. Press [OK] button on the remote control.

5.3.2. Display of SOS HistorySOS History (Number of LED blinking) indication.

From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.

This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory ship-

ment setting].

5.3.3. POWER ON TIME/COUNTNote : To display TIME/COUNT menu, highlight position, then press MUTE for (3sec).

Time : Cumulative power on time, indicated hour : minute by decimal

Count : Number of ON times by decimal

Note : This indication will not be cleared by either of the self-checks or any other command.

5.3.4. Exit1. Disconnect the AC cord from wall outlet.


12/11912

5.4. Hotel mode1. Purpose

Restrict a function for hotels.

2. Access command to the Hotel mode setup menu

In order to display the Hotel mode setup menu, please

enter the following command (within 2 second).

[TV] : Vol. [Down] + [REMOTE] : INPUT (3 times)

Then, the Hotel mode setup menu is displayed.

3. To exit the Hotel mode setup menu

Disconnect AC power cord from wall outlet.

4. Explain the Hotel mode setup menu

item Function

Mode Select hotel mode ON/OFF

Input Select input signal modes.

Set the input, when each time power is

switched on.

Selection:

---/RF/HDMI1/HDMI2/HDMI3/COMP1/

COMP2/VIDEO1/VIDEO2/PC

OFF: give priority to a last memory.

Channel Select channel when input signal is RF.

Set the channel, each time power is switched

on.

Selection:

Any channel number or [-].

[-] means the channel when turns off.

Volume Adjust the volume when each time power is

switched on.

Range:

0 to 100

Vol. Max Adjust maximum volume.

Range:

0 to 100OSD Ctrl Restrict the OSD.

Selection:

OFF/PATTERN1

OFF: No restriction

PATTERN1: restriction

FP Ctrl Select front key conditions.

Selection:

OFF/PATTERN1/ALL

OFF: altogether valid.

PATTERN1: only input key is valid.

ALL: altogether invalid.

Pow Ctrl Select POWER-ON/OFF condition when AC

power cord is disconnected and then con-

nected.

OFF: The same condition when AC power

cord is disconnected.

ON: Forced power ON condition.


13/11913

5.5. Data Copy by SD Card

5.5.1. Purpose(a) Board replacement (Copy the data when exchanging A-board):

When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.

(b) Hotel (Copy the data when installing a number of units in hotel or any facility):When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other

TVs.

5.5.2. PreparationMake pwd file as startup file for (a) or (b) in a empty SD card.

1. Insert a empty SD card to your PC.

2. Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default

(New Text Document.txt).

3. Right-click the new text document that you just created and select rename, and then change the name and extension of the

file to the following file name for (a) or (b) and press ENTER.

File name:(a) For Board replacement : boardreplace.pwd

(b) For Hotel : hotel.pwd

Note:Please make only one file to prevent the operation error.

No any other file should not be in SD card.


14/11914

5.5.3. Data copy from TV set to SD Card1. Turn on the TV set.

2. Insert SD card with a startup file (pwd file) to SD slot.

On-screen Display will be appeared according to the startup file automatically.

3. Input a following password for (a) or (b) by using remote control.

(a) For Board replacement : 2770

(b) For Hotel : 4850

Data will be copied from TV set to SD card.

It takes around 2 to 6 minutes maximum for copying.4. After the completion of copying to SD card, remove SD card from TV set.

5. Turn off the TV set.

Note:Following new folder will be created in SD card for data from TV set.

(a) For Board replacement : user_setup

(b) For Hotel : hotel


15/11915

5.5.4. Data copy from to SD Card to TV set1. Turn on the TV set.

2. Insert SD card with Data to SD slot.

On-screen Display will be appeared according to the Data folder automatically.

3. Input a following password for (a) or (b) by using remote control.

(a) For Board replacement : 2771

(b) For Hotel : 4851

Data will be copied from SD card to TV set.

4. After the completion of copying to SD card, remove SD card from TV set.(a) For Board replacement : Data will be deleted after copying (Limited one copy).

(b) For Hotel : Data will not be deleted and can be used for other TVs.

5. Turn off the TV set.

Note:1. Depending on the failure of boards, function of Data copy for board replacement does not work.

2. This function can be effective among the same model numbers.


16/11916

6 Troubleshooting GuideUse the self-check function to test the unit.

1. Checking the IIC bus lines

2. Power LED Blinking timing

6.1. Check of the IIC bus lines

6.1.1. How to access

Self-check indication only:

Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control

for more than 3 seconds.

Self-check indication and forced to factory shipment setting:

Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote con-

trol for more than 3 seconds.

6.1.2. Exit

Disconnect the AC cord from wall outlet.

6.1.3. Screen display

6.1.4. Check PointConfirm the following parts if NG was displayed.


17/119

17

6.2. Power LED Blinking timing chart1. Subject

Information of LED Flashing timing chart.

2. Contents

When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the

defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.


18/11918

6.3. No Power First check point

There are following 2 states of No Power indication by power LED.

1. No lit

2. Red is lit then turns red blinking a few seconds later. (See 6.2.)


19/11919

6.4. No Picture


20/11920

6.5. Local screen failurePlasma display may have local area failure on the screen. Fig-1is the possible defect P.C.B. for each local area.

Fig-1
http://-/?-http://-/?-


21/11921

7 Service Fixture & Tools

7.1. SC jigPurpose:

To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.

SC jig:

Jumper connector to connect to SC50 connector on SC board

Part number:

TZSC09187

How to use:

Caution: Remove SC jig from SC board after inspection.1. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.

Note: The board will be damaged if all connector is not removed (for example; remove connector only for SU board and stay

connecting with SD board. The board will be damaged.)

2. Connect SC jig to connector SC50 at left bottom side of SC board

3. Turn of the TV/Display Unit and confirm the power LED blinking.

LED blinking: Possible cause of failure is in SC board

No LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board

4. After inspection, turn off the TV/Display Unit and wait a few minutes to discharge.

5. Remove SC jig from SC board.

Remark: This SC jig can be used for all 2010 Plasma TV and Plasma Display.


22/11922

8 Disassembly and Assembly Instructions

8.1. Remove the Rear cover1. See Service Hint (Section 3)

8.2. Remove the AC inletCaution:

To remove P.C.B. wait 1 minute after power was off for dis-

charge from electrolysis capacitors.

1. Unlock the cable clampers to free the cable.

2. Disconnect the connector (P9).

3. Remove the screw (1 ) and remove the AC inlet.

8.3. Remove the P-BoardCaution:

To remove P.C.B. wait 1 minute after power was off for dis-

charge from electrolysis capacitors.

1. Unlock the cable clampers to free the cable

2. Disconnect the connectors (P2, P6, P7, P9, P11 and

P35).

3. Remove the screws (9 ) and remove the P-Board.

8.4. Remove the Side terminal

cover and Side shield metal

1. Remove the screws (2 , 1 , 1 ).

2. Remove the Side terminal cover.

3. Remove the Side shield metal.


23/11923

8.5. Remove the Tuner unit1. Unlock the cable clampers to free the cable.

2. Disconnect the connectors (A1, A6, A7 and A11).

3. Disconnect the flexible cables (A31, A32 and A33).

4. Remove the screws (2 ) and remove the Tuner unit.

8.6. Remove the A-Board1. Remove the Tuner unit. (See section 8.5.)

2. Remove the screws (2 ) and remove the A-Board.

8.7. Remove the Speakers1. Unlock the cable clampers to free the cable.

2. Disconnect the Speaker terminal.

3. Remove the screws (2 each) and remove the Speak-

ers (L, R).

8.8. Remove the SU-Board1. Remove the flexible cables (SU1, SU2, SU3, SU4 and

SU5) connected to the SU-Board.

2. Remove the flexible cable (SU11-SD11) and the bridge

connector (SC41-SU41).

3. Remove the molding prop (1 ).

4. Remove the screws (2 , 2 ) and remove the SU-

Board.

8.9. Remove the SD-Board1. Remove the flexible cables (SD1, SD2, SD3, SD4 and

SD5) connected to the SD-Board.

2. Remove the flexible cable (SU11-SD11) and the bridge

connectors (SC42-SD42 and SC46-SD46).

3. Remove the molding prop (1 ).

4. Remove the screws (2 , 2 ) and remove the SD-Board.


24/11924

8.10. Remove the SC-Board1. Remove the SU-Board and SD-Board. (See section 8.8.

and 8.9.)


3. Disconnect the connector (SC2).

4. Disconnect the flexible cable (SC20).

5. Remove the screws (6 ) and remove the SC-Board.

8.11. Remove the SS2-Board1. Remove the Tuner unit. (See section 8.5.)

2. Disconnect the bridge connector (SS21-SS24) and dis-

connect the flexible cable (SS58).

3. Remove the screws (2 ) and remove the SS2-Board.

8.12. Remove the SS-Board1. Remove the Tuner unit. (See section 8.5.)


3. Disconnect the connectors (SS11 and SS33).

4. Disconnect the flexible cables (SS53 and SS56).

5. Disconnect the bridge connector (SS21-SS24).

6. Remove the screws (6 ) and remove the SS-Board.

8.13. Remove the Hanger metals and

the One leg bracket1. Remove the Plasma panel section from the servicing

stand and lay on a flat surface such as a table (covered

by a soft cloth) with the Plasma panel surface facing

downward.

2. Remove the One leg bracket fastening screws (4 )

and the One leg bracket.

3. Remove the Hanger metals (L, R) fastening screws (2

each) and remove the Hanger metals (L, R).


25/11925

8.14. Remove the Cabinet mount

metals1. Remove the One leg bracket. (See section 8.13.)

2. Remove the Cabinet mount metals fastening screws (10

, 20 ) and remove the Cabinet mount metal top

and the Cabinet mount metal bottom.

8.15. Remove the C1-Board1. Remove the Cabinet mount metal bottom (See section

8.14.).

2. Remove the flexible cables holder fastening screws (5

).

3. Disconnect the flexible cables (CB1, CB2, CB3 and CB4).

4. Disconnect the flexible cable (C10).

5. Remove the screws (4 ) and remove the C1-Board.

8.16. Remove the C2-Board1. Remove the Hanger metal R and the One leg bracket.

(See section 8.13.)

2. Remove the Cabinet mount metal bottom (See section

8.14.).


).

4. Disconnect the flexible cables (CB5, CB6, CB7 and CB8).

5. Disconnect the flexible cables (C20, C21 and C26).


8.17. Remove the C3-Board1. Remove the Tuner unit. (See section 8.5.)

2. Remove the Hanger metal L and the One leg bracket.

(See section 8.13.)

3. Remove the Cabinet mount metal bottom (See section

8.14.).


).

5. Disconnect the flexible cables (CB9, CB10, CB11, CB12,

CB13, CB14 and CB15).

6. Disconnect the flexible cables (C31 and C36).7. Disconnect the connectors (C33 and C35).



26/11926

8.18. Remove the Plasma panel sec-

tion from the Cabinet assy1. Remove the Cabinet mount metals fastening screws (10

).

2. Remove the cabinet assy and the plasma panel fastening

screws (3 , 8 ).

3. For leaving the plasma panel from the front frame, pull the

bottom of the cabinet assy forward, lift, and remove.

8.19. Remove the Contact metals1. Remove the Cabinet assy. (See section 8.18.)

2. Remove the screws (4 ).

3. Remove the Contact metal top.


5. Remove the Contact metal bottom.


7. Remove the Contact metal side (L, R).

8.20. Remove the K-Board1. Remove the Contact metal bottom. (See section 8.19.)

2. Remove the screw (1 ).

3. Remove the claw (1 ).

4. Disconnect the connector (K1) and Remove the K-Board

from LED Panel.


27/11927

8.21. Replace the plasma panelCaution:

A new plasma panel itself without Hanger metals is

fragile.

To avoid the damage to new plasma panel, carry a new

plasma panel taking hold of the Hanger metals after

assembling the Hanger metals and the One legbracket.

1. Place a carton box packed a new plasma panel on the flatsurface of the work bench.

2. Open a box and without taking a new plasma panel;

Attach the C1-Board, C2-Board and the C3-Board, con-

nect the flexible cables from the plasma panel to the C1-

Board, C2-Board and the C3-Board, and fit the flexible

cable holders.

3. Attach the Hanger metals and the One legbracket to the

new plasma panel.

4. Place the plasma panel on the servicing stand taking hold

of the Hanger metals.

5. Attach the cabinet assy and each P.C.Board and so on, to

the new plasma panel.

*When fitting the cabinet assy, be careful not to allow anydebris, dust or handling residue to remain between thefront glass and plasma panel.


28/11928

9 Measurements and Adjustments

9.1. Adjustment

9.1.1. Vsus selectionCaution:

When Plasma panel or A-board is replaced, Vsus should be set to LOW or HIGH.

Procedure

1. Go into main item [VSUS] in Service Mode. LOW or HIGH will be displayed.2. Press [OK] button to go to TEST stage.

White pattern without On-Screen Display will be displayed during TEST and CONF stage. Press [5] button to display the

On-Screen Display.

3. Press [VOL (-)] button to set to LOW.

4. In LOW setting

a. If no several dead pixel is visible remarkably in white pattern, press [3] button to go to CONF stage.

b. If the several dead pixels are visible remarkably in white pattern, Set to HIGH by press [VOL (+)] button. Press [3] button

to go to CONF stage if the symptom is improved.

5. Press [OK] button in CONF stage to store LOW or HIGH.

6. Exit Service Mode by pressing [Power] button.


29/11929

9.1.2. RF video sub contrast adjustment

Name of measuring instrument Remarks

1. REMOTE TRANSMITTER

2. RF analog signal (Sprit color bar. The pattern for adjustment must contain 100% white part.)

Procedure Remarks

1. Receive the sprit color bar with RF analog signal.

(ASPECT FULL, Picture menu: Vivid)

2. Enter Service mode menu, and select ADJUST -- CONTRAST.

Pushing the remote controller [OK] key for about 3 seconds, GAIN is suited to the adjustment value automatically.


30/11930

9.1.3. White balance adjustment

Name of measuring instrument Remarks

Color analyzer

(Minolta CA-100 or equivalent)

Note:The CA-100 which was calibrated to less than +-0.001 with CS-1000.

Procedure Remarks

Make sure the front panel to be used on the final set is fitted.

Make sure a color signal is not being shown before adjustment. Put the color analyzer where there is little color variation.

1. Set to Service mode, WB-ADJ.

2. Select [VIVID] for picture menu.

3. Select [Cool] for color temperature.

4. Push [5] key of remote controller to display window pattern.

5. Confirm the brightness. The following is the confirmation value.

TC-P50G20/25 215cd/m2

6. Select [Cinema] for picture menu.

7. Select [Warm] for color temperature.

8. Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1.

9. Attach the sensor of color analyzer to the center of window pattern.

10. Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer become the [Color temperature

Low] in table 2.

11. Increase RGB together so the maximum drive value in RGB becomes [FF].

That is, set [ALL DRIVE] to [FF].

Execute adjustment again. When that, the maximum value of R/G/B DRV should be

[FF], and either R/G/B DRV should be [FF].

12. The average of the adjusted values in color temperature Cool, Mid, and Warm is shown in Table 4.

The setting value for color temperature Cool will be calculated by multiplying the adjusted value of color tempera-

ture Warm to the ratio of the value of Warm and Cool in each GBR value in Table 4.

Write that values to the data area of color temperature Cool in EEPROM (Table 3).

13. The setting value for color temperature Mid will be calculated by multiplying the adjusted value of color tempera-

ture Mid to the ratio of the value of Warm and Mid in each GBR value in Table 4.

Write that values to the data area of color temperature Mid in EEPROM.

14. Select [VIVID] for picture menu when you check the adjusted data of Cool and Normal.

Note :Adjusted valuemust be written to

both SD data area

and HD data area

of the EEPROM.


31/11931


32/11932


33/119

33

10 Block Diagram

10.1. Main Block Diagram

LED:4TIME

LED:6TIMES

LED:7TIMES

COLD H

:3ME

LED:6TIMES

:1ME

LED:8TIMES

LED:12TIMES

LED:7TIMES

:5ME

RECTIFIE

SCAN OUT (LOWER)

ON/OFF CONTRO

CONTROLPULSE

C21

P2

VIDEODATA

SD11

VSUS

SC41

SC

VSUS

Vda

P6

SCAN OUT (UPPER)

DATDR

VSCAN GEN.

C10

VIDEO DATA

SD42

VIDEO DATA

SU

C26

SUSTAIN CONTROLBUFFER

POWER SUPPLY

POWER MICO

SC20

DATADRIVER

C2

SCAN CONTROL

SD

DATADRIVER

P+5V

SU11

P+15V

DATADRIVER

DATA DRIVER (LEFT

P

SOS6_SC1

C3

SC-BOARDENERGY RECOVERYSOS DETECT

C20

C31

DATADRIVER

Vda

VAD GEN.

F15V

DATADRIVER

SD46

SC2

STB5V

DATA DRIVER (CENTER)

P+3.3

V

P+5V

P+3.3

V

P+5V

P+15V

SU41

C36

SCAN DRIVE

DATADRIVER

SC46

SC42

DATADRIVER

DATA DRIVER (RIGHT)

SC-BOARDFLOATING PARTSOS DETECT

SOUND15V

STB5V

F15V

C1

SOS7_SC2

SOS8_SS

DATADRIVER

P+3.3V,P+5V

PS SOS4

P+3.3V

P7

P+15V

VIDEO

DATA

STANDBYVOLTAGERECTIFIE

SCANDRIVER

DATADRIVER

DATADRIVER

SCANDRIVER

P+5V

SUB1.5V

SUB5V

SUB1.2V_D

CPU BUSI/F

F15V

CPU BUS

A33

EEPROM

LVDS DATA

V

A

VIDEODATA

OPTICAL AUDIO OUT

(SIDE)

C.A.T.S. SENSOR

PLASMA AICPG with SSH/V Sync ControlSub Filed ProcessorPlasma AI

A11

P+3.3

V

REMOTE IN

HDMI I/F

PWM

_L/R

VIDEO1

SUB9V

SOS7_SC2

STB5V

TS_IN

COMP1

SOUND15V

SIF_OUT

AV SW

SUB1.2V_A

HDMI1-3

AV I/O

DCDC

TMDS DATA

SOS6_SC1

L/R

SUB1.2V_A

SUB3.3V

POWER LED(R)

ANALOG-ASIC

L/R

P+5V

R/G/B

VIDEO2

STB5V

L

Y/PB/PR

A31

IFD_OUT

AMP

SOS8_SS

SOS7_SC2

L/R

V

OUT

SUB9V

P+5V

SIF_IN

ETHE

PANELMAINON

V

ETHERPHY

VIDEO DATA

PC_H/V

SOS8

_SS

L/R TV

SOS6_SC1

L/R MONITOR OUT

STB3.3V

USB

P+3.3

VDET

L/R

RECEIVER

KEYSCAN1

L/R

SOUNDSOS

P+15V

SOUND SOS

AUDIO

COMP2

LVDSD

ATA

SCAN CONTROL

PANELSOS

SOUND SOS DETCIRCUIT

P+5VDET

OPTICAL

SD CARD DATA

PEAKS-LDA2

TUNER

FRONT ENDPROCESSOR

OPTICALOUT

CH0DATA

SPEAKER(R)

DDR3

EEPROM

Y/PB/PR

1GbitNAND FLASH

DCDC

SUB1.2V_D

DCDC

CLOCK

SUB5V

AUDIO I/O

PWM_L/R

A6

PANEL MAIN ON

P+15V

P+5V

SUB1.5V

A7

P+3.3

V

SUB3.3V

F15V

DCDCSUB9V

SUB+5V DET

SUB+9V DET

SUB5V

AUDIO

SUB9V

PD4-H

Y/PR/PB

DIGITAL SIGNAL PROCESSOR

PANELSOS

SYSTEM MPU

R

SUB+3.3V DET

A32

SUB3.3V

KEYSCAN3

SUSTAINCONTROL

SPEAKER(L)

PC

(LED:4TIME)

(LED:6TIMES)

(LED:7TIMES)

COLD H

(LED:3TIMES)

(LED:6TIMES)

(LED:12TIMES)

(LED:8TIMES)

(LED:12TIMES)

(LED:7TIMES)

(LED:5TIMES)

LED:4TIMES POWER SOSDCC_SOS

(LED:4TIMES)

LED:9TIMES(LED:9TIMES)


34/119

34

10.2. Block (1/4) Diagram

P

Q5603

F15V

D5602

Q5602

SUB3.3V

VJ5

453

SUB3.3V

P+15V

SUB5V

SUB3.3V

SUB1.5V

SUB9V

STB5V

SOUND15V

P_S1

PEAKS-LDA2

F15V

A7

VSB_

INP

7

8

PANEL_MAIN_ON

SOS4_PS

VSB_

INP

STB5V

3

1

7

R/G/B/H/V

F15V

2

PC

9

SOUND15V

SDDATA:4bit

8

SDCARD

I/F

P7

STB5V_SW_ON

SD

JK

9

L/R

F15V

L/R

L/R

1

V

SOUND15V

Y/PB/PR

P+15V

VIDEO1

COMP1

V

VIDEO2

L/R

COMP2

Y/PB/PR

F15V DET ON/OFF

3

4

5

P_S0

6

P_S1

TV_SUB_ON

PANEL_MAIN_ONECO ON

SOS4_PS

STB5V_SW_ON

TV_SUB_ON

ECO ON

P_S0

DIGITALDEMODULATOR

IC8300

IF_

AGC

IIC_TU

IIC0

FRONT ENDPROCESSOR

Y/PR/PB

L/R

AV SW

PC_G

VIDEO1

D2_PR

PC_B

D1_L

D2_L

PC

V1_R

D2_Y

PC_RJK3001

D1_Y

ANT IN

TV_

V

RF_

AFT

COMP2

IIC_TU

V1_V

D2_PB

TU8300

JK3701

TUNER

IFD_

OUT2

V2_L

V1_L

COMP1

IFD_

OUT1

5VV

IDEO

D1_PR

(SIDE) V2_R

D1_R

AFT

JK3000

PC_H

D1_PB

PC_V

VIDEO2

D2_R

V2_V

V

TV

IF_

AGC

A6P6

+5V

HDMI_CEC

DDC_

2_

IIC

DDC_

2_

IIC

+5V

DDC_

0_

IIC

TMDSDATA

CLOCK

RX1

RX2

DDC_

1_

IIC

HDMI_CEC

RX3

TMDSDATA

CLOCK+

5V

TMDSDATA

CLOCK

DDC_

0_

IIC

DDC_

1_

IIC

HDMI_CEC

JK8702

100BASE-TX

10BASE-T/

ETHER

NET

ETHERNET

IC8703

ETH

ERPHY

ETHERNET IF

CH0DATATS_IN

ETHERPHY

EEPROM

CPUBUS

I/F

DDRI/F

1GbitDDR3

IIC_

IF

USB_1,2

JK8700

USB

US

B

IC8240,41

CLOCK

CLOCK GEN

+1.5V

SUB1.5V

+3.3V

+1.2V

SUB1.2V_DIC5500

+1.2V

SUB3.3VIC5501

SUB1.2V_A

IIC1_EEP

IC8303

1.2V

IC5401

9V

5V9V

SUB5VTUNER

IC5607

5V

SUB1.2V

D

SUB1.2V_

A

3.3V

SUB5V_USBIC5608

+5V

SUB1.5V

VDDSD

AVDDH

ACHIP3.3V

IC8501AVDDH

IC5604

3.3V

IC5603

PC_H/V

MAIN

SIF_

OUT

SIF_IN

H/V

Y/PR/PB

L/R

IIC0

VCC

IC8000

AV I/O

HDMI I/F RECEIVER

DIGITAL SIGNAL PROCESSORA

IC8502

IC8100

IC3001

1G bitNAND FLASH

HDMI IN 3

JK4502

(SIDE)

JK4501JK4500

HDMI IN 2HDMI IN 1

HDMI_CEC

DDC5V

USB5V

IC8704

L/R

L/R TV

L/R MONITOR OUTL/R

INMONITOR

RF_

AFT

FE_

XRST


35/119

35


LED:3TIMES

LED:5TIMES

LED:6TIMES

LED:7TIMES

LED:8TIMES

LED:4TIMES

LED:12TIMES

P+5V

P+3.3V

SUB3.3V

STB5V

SW25

D5614

STB3.3V

D5615

D5613

SUB9V

SUB5V

SUB9V

STB5V

P+15V

P+15V

X1100

Q5684

P+3.3V

Q5475

D5470

Q5478

SUB3.3V

TEMP SENSOR

+5V

P_S

P_S

IC4800

LVDS DATA

P_S0

P_S1

+1.2V

+3.3V

P+5V DET

P+3.3V DET

IIC0

A DIGITAL SIGNAL PROCESSOR

POWER ON/OFF

TV SUB ON

PANEL SOS

ECO ON

TV SUB ONECO ON

SUB3.3V DET

SUB9V DET

SUB5V DET

STB+3.3V

IC9803

IC9800

IC9801

XRST_SYS

SOS7_SC2

SOS6_SC1

SOS8_SS

KEY SW

KEYSCAN3

POWER

KEYSCAN1

GENXIIC

GENXIIC EEPROM

IC1101

STB_RST

RESET

IC5606

STB_RST

KEYSCAN3

AC_SW_OFF

SOS_DCC

PANEL SOSPANEL SOS

DRVRSTDRVRST

PD4H_DRVRSTPD4H_DRVRST

PANEL SOS

PANEL MAIN ONPANEL MAIN ON

SOS4_PS

D_U

SOS4_PS

SOS_DCC

SOS6_SC1

SOS7_SC2

SOS8_SS

IC5480

ANALOG-ASIC

SYSTEM MPU GenX8

STB3.3V

PD4H_DRVRST

XRST_SYSXRST_SYS

STB_RSTSTB_RST

DRVRSTDRVRST

DTV_RSTDTV_RST

IIC1IIC1

4

5

2

7

3

1

6

LVDS DATA

IC1100

DDC5V_B

HDMI_CEC_IN_OUT

DDC5V_A

DDC5V_C

SOUND SOS

DDC5V_A

DDC5V_B

DDC5V_C

HDMI_CEC_IN_OUT

SOUND SOS

OSD_VINOSD

10MHz

OSCX0

OSCXI

SC_UHZSC_UHZ

D_UHZD_UHZ

D_UHZ

PD4

XRS

RF_AFTRF_AFT

DDC_0_IIC

DDC_1_IIC

DDC_2_IIC

REMOTE IN

C.A.T.S. SENSOR

REMOTE IN

POWER LED(R)

C.A.T.S.(AI)

POWER LED(R)

KEYSCAN1

KEYSCAN3

KEY3/STBY_LED_ON

KEYSCAN1

DDC_1_IIC

DDC_0_IIC

DDC_2_IIC

SBI1/SBO1RXD1/TXD1

STB_RST

SW_OFF_DET

SW_OFF_DET

POWER_DET

STB5V_SW_ON

AC_SW_OFF

SW_OFF_DETSW_OFF_DET

IC

IM

VV

CC

SW3759SW3761SW3762SW3763SW3764SW3765

(LED:3TIMES)

(LED:5TIMES)

(LED:6TIMES)

(LED:7TIMES)

LED:9TIMES(LED:9TIMES)

(LED:8TIMES)

(LED:4TIMES)

(LED:12TIMES)

1.2V

3.3V

FLAADDR/DATA

FLASHMEMORY

IC9304


36/119

36


COLDOT

COLDOT

LED:4TIMES

D403

D402

F601

D551

D351

D504

F201

D705

F501

F602

D401

D552

5A 250V

VR401

Q601,04,06

MAINSW_

ON

BIAS 5V

MAINSW2

IC551

VSET1/VSET2

STB5V_

ON/OFF

MAINSW1

LIVE

Q401

STB+5V

MAIN SW2

10A 250V

5

Q407

MAIN SW1

IC251

A7OPEN

Q702

Q408

PC202

ACDET

PC502

IC403

Q503

Vda_Vo

T201

IC202

K605

L601,L602

IC701

PC504

K602

Q502,05,06

P POWER SUPPLY

Q355

Q557

1 1

VSET1/2

3

Q251,Q252

L603

VdaDET

STB+5V

CONT

12

Q405Q406

Q504

FETDRIVER

14

VDET

1

BIAS

3

Q404

P34

IC352

VdaDET

Q706

L351

RF601

Q701

15V_OUT DET

+5V

15V

D501

VGH VGL

RECTIFIER

PFC

OCP

Vsus

Vda

FB

Q402

NEUTRAL

VC1

BIAS_PFC

Q551F+15V

Q602,Q603

ALLOFF

MAINSW1

IC201

Q201,Q202

MAINSW2

S1

TVSUBON

VdaCONTROL

RESONANCE

BIAS_PFC

BIAS_MAIN

PHOTO COUPLER

P92

BIAS_MAINPHOTO COUPLER

T501

K604

PHOTO COUPLER

MAIN RELAY_ON

S0

S1

COMPARATOR

Q403

2A 250V

RESONANCECONTROL

VR251

IC601

LIVE

ALL OFF

AC CORD

4

FILTER

P7

RECTIFIER

PC501

NEUTRAL

PHOTO COUPLER

PHOTO COUPLER

Vda

Q203

STBERROR DET

IC501

PC201

CONTROL

AC DET

P+15V

STB

POWER MICOM

VsusERROR DET

Vsus_Vo

DET

TV SUB ON

15V_IN

L402

PANEL_MAIN_ON

11

P

10A 250V

D603

S0

SOS4_PS

F_

15V_

ON

L401

Vsus

RECTIFIER

D609

D253D254

COLDHOT

COLDHOT

(LED:4TIMES)


37/119

37


LED:7TIMES

LED:6TIMES

D16583

D16822

TPVSCN

D16490

D16721

D16493

D16901

TPSC1

TPVSUS

TPVAD

D16618

D16820

TPSOS6

TPSOS7

D16920

D16480

D16728

D16475

D16473

D16791

D16476

D16821

CML

Vda

DATA DRIVER (RIGHT)

SS11

PC16685

IC1

C1

OC2

C10 C20

SEL

CLK

C33SS33

IC16563

VSCN-F

ELECTRODES

CML

SOS6_SC1

IC16471

6

Q16608CRC1

CB11

2

SC41

1

SC20

NAND

CB9

SOS7_SC2

COMPARATOR

5

16

20

Q16441

7

8

SD1-SD5

IC1

1

CPH1

CERS

Vda

(SC1)

4

CEL

5V_F

PHOTO COUPLER

Q16621

OC1

F16V GEN.

IC16771

Vfo

CMH

SD42

PHOTO COUPLER

20

PHOTO

IC16490,91

SD46

CSL

SCAN

8

Q16885

Q16661

C26

Q16490

18

DRIVER

6

SU11

VOL

SCAN

CB10

PANEL SCAN

COUPLER

SU

8

SCAN OUT (UPPER)

1

IC14801-03

CEL

Vfo

1

5

CIS

SC42

CEL

VHIZ

ERROR DET

LED(G)

SIU

8

21

4

7

C36

Q16607

IC16792,93

SD

F16V

SCAN OUT (LOWER)

4

1

Vda

CRC1

CSL

5

T16471

DRIVER

CRC2

3

2

SHUNTREG

CSH

SOS8_SS

REG.

SCAN

COMPARATOR

2

Q16818

F16V

SCNR_PRO

IC16521

PHOTO

2

IC16773

SC50

IC16692

COUPLER

1

Q16421Q16422

SEL

SIU

IC16501

CMH

INVERTER

Vsus

CERS

SC

VFG

IC16661

SCAN DRIVE

Q16660

18

ERROR DET

TP59,TP60TP61,TP62

CSH/CMH GATEDRIVE CIRCUIT

D16859

EN

1

20

IC16724

CSL/CML GATEDRIVE CIRCUIT

PC16684

CIS

CPH1

CB2

VHIZ GEN.

7

PC16603

P+5V

BUFFER

7

UHZ

CB4

Vad+5V

SHUNT

IC16691

PANEL DRIVER

A31

UHZ

OC1

DATA DRIVER (CENTER)

SC2

PANEL DRIVER

SU41

C2

IC16920

PLASMA PANEL

P11

CB3

OC2

SUSTAIN CONTROL

C21

D16482

SS

CB6

Q16601

SU1-SU5

1

CB8

DRIVER

Q16876

6

+5V

CB5

SUST

33

LOGIC IC

CLK

IC14604-06

VIDEODATA

DRIVER

CONTROLDATA

IC

CB1

IC17201

6

1

SCAN

3

SUSTAIN

BUFFER

SCAN CONTROL

CB7

VSU

P2

35

SC46

59

BU

VIDEODATA

Vsus

CRC2

IC14601-03

9

DR

PC16480

33

REC

40

A33

1

SCANCONTROL

4

SD11

INVERTER

CONTROL DATA

PLASMA PANEL

CSH

VIDEO DATA

VHIZ

35

32

CIRCUIT

8

SEPA PROTECT

1

IC16561,62

40

37

IC16581

Vda

P+5V

P+3.3V

P+5V

P+3.3V

P+3.3V

P+15V

P+15V

P+3.3V

P+3.3V

P+15V

Q16647

99

15V_F

Q16471CHA

SCNR_PRO

CHA

2SC JIG

Vscn

VFG

D16872

CMHPHOTO

PC16461

(16V_F)

CSH

VRH

D16871

COUPLER

P+15V

MID

VRL

PC16722,23

IC16786,87

SHUNT REGVAD GEN.

IC16784,85

IPD CIRCUIT

IPD CIRCUIT

PC16896,97

SHUNT REGVSCN GEN.

IC14804-06

IC14901,02,04

Q16452Q16622

Q16403

D16462

Q16402

(LED:7TIMES)

(LED:6TIMES)


38/119

38


39/11939

11 Wiring Connection Diagram

11.1. Caution statement.Caution:

Please confirm that all flexible cables are assembled correctly.

Also make sure that they are locked in the connectors.

Verify by giving the flexible cables a very slight pull.

11.2. Wiring (1)


40/11940

11.3. Wiring (2)


41/11941

11.4. Wiring (3)


42/11942


43/119

43

12 Schematic Diagram

12.1. Schematic Diagram Note


44/119

44

12.2. P-Board (1/3) Schematic Diagram

E

B

4

D

31

C

5

F

2 6

A

! P-BOARD ETX2MM806ASH (1/3)

HOT

COLDHOT

STB

CONTROL

PFC


45/119

45


RESONANCE

CONTROL

COMPARATOR

Vsus

ERROR DET

Vsus

P+15V

Vda

CONTROL

COLDHOT

COLDHOT


E

B

4

D

31

C

5

F

2 6

A


46/119

46


E

B

4

D

31

C

5

F

2 6

A


POWER MICOM


47/119

47

12.5. A-Board (1/18) Schematic Diagram

S

S

AH

_ED2

AH

_ED6

AH

_ED4

AH

_ED1

AH

_ED0

AH

_ED7

AH

_ED5

AH

_ED3

PD_ED1

PD_ED0

PD_ED7

PD_ED6

PD_ED5

PD_ED4

PD_ED3

PD_ED2

AH_ED3

AH_ED4

AH_ED5

AH_ED6

AH_ED7

AH_ED0

AH_ED1

AH_ED2

SUB3.3V

C890316V0.1u

C890416V

0.1u

C895016V

0.01u

TC-P50G20:TVRR441ABSTC-P50G25:TVRR242ABS

*IC8502

1 NC

2 NC

3 NC

4 VSS 5SDA

6

SCL

7

WC

8VCC

TVRR239S

IC8501

1

NC

2

NC

3

NC

4

NC

5

NC

6

NC

7

R/B#

8

RE#

9

CE#

10

NC

11

NC

12

VCC

13

VSS

14

NC

15

NC

16

CLE

17

ALE

18

WE#

19

WP#

20

NC

21

NC

22

NC

23

NC

24

NC

25

NC

26

NC

27

NC

28

NC

29

I/O0

30

I/O1

31

I/O2

32

I/O3

33

NC

34

NC

35

NC

36

VSS

37

VCC

38

NC

39

NC

40

NC

41

I/O4

42

I/O5

43

I/O6

44

I/O7

45

NC

46

NC

47

NC

48

NC

SUB3.3V

SUB3.3V

R8503

R8504

TP8563

PD_XNFRE

PD_XNFCE

PD_NFALE

PD_XNFWP

PD_XNFWE

PD_NFCLE

PEAKS_SCL1

PD_NFRYBY

PD_ED[0-15]

PD_HSDOUT6

PEAKS_SDA1

R894456

R894756

R894556

R89512.2k

R894856

R85004.7k

R8501

68

R894656

R895056

R895210k

R894956

R8918

EXB2HV680JV

1Gbit NAND_FLASH

PEAKS-LDA2

PORT5[7]EEPROM_WP

IIC1

F

2

E

4

C

6 1

A

B

3 5

D

EEPROM

EEPROM

! LDA2_ROM,SPC

TO 15/18

TO 15/18

TO 2,15/18

TO 15/18

TO 2,7,11/18

TO 15/18

A-BOARD (1/18)TXN/A1MGUUS (TC-P50G20)TXN/A1LPUUS (TC-P50G25)


48/119


49/119

49


+

D.SW

W.P.

S

S

PP

P PAP_MDC

AP

_MII_T

XD3

AP

_MII_T

XD2

AP_MII_TXD1PD_MII_CRS

AP_MII_TXD0

PD_MII_COL AP_MII_TXEN

PD_MII_RXER

PD_MII_RXDV

PD_MII_RXD3

PD_MII_RXD2

PD_MII_RXD1

PD_MII_RXD0

PD_MII_RXCLK

AP_MII_TXEN

AP

_MDC

AP

_MDIO

AP_MII_TXD3

AP_MII_TXD2

PD_MII_TXCLK

AP_MII_TXD1

PD

_MII_C

RS

PD

_MII_C

OL

AP_MII_TXD0

PD_MDIO_INTL

PD

_MII

_RXD3

PD

_MII

_RXD2

PD

_MII

_RXD1

PD

_MII

_RXD0

PD_MII_TXCLK

PD_MDIO_INTL

AP

_PHYR

STL

PD_MII_RXER

PD_MII_RXCLK

AP_PHYRSTL

PD_MII_RXDV

AP_MDIO

C8718

16V0.1u

C8712

16V 0.1u

C8720

16V0.1u

C8714

50V

100p

C8722

10u10V

C8719

16V0.1u

C8721

16V 0.1u

C8711

10u10V

C8713

16V 0.1u

C871710u10V

C8602

16V

0.1u

C8601

16V

0.1u

C861016V

0.1u

C8617

16V0.01u

C8570

16V 0.01u

C8565

16V0.01u

C8512

16V0.1u

C8513

16V0.1u

C860916V

47u

IC8703C1CB00003239

1GND

2GND

3GND

4VDDA_1.8

5VDDA_1.8

6V1.8_OUT

7VDDA_3.3

8VDDA_3.3

9RX-

10RX+

11TX-

12TX+

13

GND

14

XO

15

XI

16

REXT

17

GND

18

MDIO

19

MDC

20

RXD3/PHYAD0

21

RXD2/PHYAD1

22

RXD1/PHYAD2

23

RXD0/DUPLEX

24

GND

25VDDIO_3.3

26VDDIO_3.3

27RXDV/CONFIG2

28RXC

29RXER/ISO

30GND

31VDD_1.8

32INTRP

33TXC

34TXEN

35TXD0

36TXD1

37

GND

38

TXD2

39

TXD3

40

COL/CONFIG0

41

CRS/CONFIG1

42

LED0/MWAYEN

43

LED1/SPEED

44

NC

45

NC

46

NC

47

RST#

48

NC

JK8702K2LC1YYA0005

1

2

3

4

5

6

7

8

JK8600K1NA09E00080

1

2

3

4

5

6

7

8

9

10

11

12

L8701

J0JHC0000045

L8706

J0JHC0000045

L8509

J0JHC0000045

L8702

J0JHC0000045

L8705

J0JHC0000045

T8301

G5BYC0000015

1

2

3

4

5

6

9

10

11

12

8

7

SUB3.3V

VDDSD

SUB3.3V

SUB3.3V

SUB3.3V

R8702

R8713

VJ8701VJ8703

VJ8702 VJ8700

TP8604

TP8607

TP8603

TP8605

TP8601

TP8602

TP8606

TP8608

TP8600

PD_MII_TXD3

PD_SDCLK

PD_MII_TXD0

PD_PHYRSTL

PD_MII_TXEN

PD_MDC

PD_MII_TXD1

ETHER_25M

PD_MII_TXD2

PD_SDCMD

PD_MII_RXD0

PD_MII_RXD2

PD_MII_TXCLK

PD_MII_RXDV

PD_MII_RXD3

PD_MII_RXER

PD_MII_RXD1

PD_MII_CRS

PD_MII_RXCLK

PD_MII_COL

PD_SDCD

PD_SDDAT0

PD_SDDAT2

PD_MDIO

PD_MDIO_INTL

PD_SDWP

PD_SDDAT3

PD_SDDAT1

EXB28V560JX

R8728

R8714

D1HG1038A002

R8526

49

.9

R8527

49

.9

R87376.49k

R8711 4.7k

R8724 56

R8710 56

R87 19 2 2

R8381

75

R87 48 2 2

R8752

10k

R8588

0

R87 15 5 6

R8731

56

R8698 56

R8751

10k

R87 43 2 2

R8706 56

R8709 56

R8716 56

R8718 56

R8704 56

R8699 56

R8735

10k

R8707 56

R8717 56

R8703 56

R8733

56

R8722 56

R 87 23 5 6

R8721 56

R8734

0

R8708 56

R 87 01 5 6

R8725 56

R87 20 2 2

R8712 4.7k

R8383

75

R8696 56

R8384

75

R8382

75

R87 55 0

R8705 56

R8779

0

R8524

49

.9

R8525

49

.9

R8697 56

R8700 56

PEAKS-LDA2

PEAKS-LDA2

SDCMD

SDDAT1

SDCD

SDWP

SDDAT2

GND

GND

SDCLK

SDDAT0

3.3V

SDDAT3

TX+

TX-

RX+

RX-

TX+

TX-

RX+

RX

-

19 21 242320 22

LAN

SD

! LDA2_PERIPHERAL

ETHERNET IF

ETHERNET

100BASE-TX

10BASE-T/

SD CARD SLOT

TO 2/18

TO 15/18

TO 15/18



50/119


51/119

51


+

ThermalPad

S

S S

S

S

P

P

P

P

IF_Monitor21

FE_IF_AGC

RF

_VIDEO

_OUT

0V

PD

_CH0DATA

PD

_CH0VAL

RF_V

PD

_CH0PSYNC

PEAKS

_SCL0

PEAKS

_SDA0

PD

_XIRQ2

PD_CH0CLK

FE_IF_AGC

PD_CH0DATA

PD_CH0PSYNC

PD_CH0VAL

PEAKS_SDA0

PD_XIRQ2

FE

_SCL

_TU

PD_CH0CLK

RF_VIDEO_OUT

RF_AFT

RF_AFT

PEAKS_SCL0

XRTS0

XRTS0

FE_SCL_TU

FE_SDA_TU

RF

_V

FE

_SDA

_TU

C8303

50V220p

C8321

50V

120p

C832716V

0.1u

C8329

10u

10V

C8310

16V

0.1u

C8315

1000p

50V

C831216V 0.1u

C8309

50V1000p

C830150V220p

C8302

50V 220p

C8307

50V

1000p

C8316

1000p

50V

C8330

10u

10V

C8328

16V0.1u

C8343

10V

1u

C8326

16V0.01u

C8335

16V0.1u

C8334

16V0.1u

C8340

16V0

.1u

C8333

16V 0.1u

C8339

16V0.1u

C8341

16V0.1u

C833716V0.1u

C8332

16V0.1u

C8331

16V0.1u

C833850V

18p

C8336

50V

15p

C8345

10u

10VC8342

16V

0.1u

C8344

10u

10V

C8324

16V

0.1u

C8323

1000p50V

C8322

1000p

50V

C8325

16V0.1u

C8354

10V10u

C8350

4.7u10V

C8349

4.7u10V

C8313

10u

10V

C8314

10u10V

C8400

6.3V220u

C0DBGYY00612

IC8303

1

ON/OFF

2

VSS

3

NC

5

VOUT

4

VIN

MN88436

IC8300

1

VDDH0

2

XI

3

XO

4

VSS0

5

GPI

6

INT

7

VDDL0

8

SDA

9

SADR1

10

CSEL0

11

SCL

12

CSEL1

13

GPO0

14GPO1

15GPO2

16GPO3

17GPO4

18GPO5

19

GPO6

20NRST

21SADR0

22VDDH1

23SCK

24

VSS1

25

SDO

26

PCK

27

VDDL1

28

DEN

29

GPO7

30

GPO8

31

TEST0

32

MSDA

33

TEST1

34

MSCL

35

TEST2

36

AGCRF

37

VSS2

38VDDH2

39AGCIF

40VDDL2

41TESTA

42

ADIRF43

ADVRH44

ADVRL

45VDDA

46ADINN

47ADINP

48

VSSA

L8312J0JGC0000070

L8310

J0JYC0000068

L8311

J0JHC0000045

L8308J0JHC0000045

L8307J0JHC0000045

L8305

G1CR10JA0020

L8303

G1CR39JA0020

L8304

G1CR39JA0020

SUB3.3V

SUB5V_TUNER

SUB3.3V

SUB3.3V

SUB3.3V

R8337

R8329

R8333

R8305

R8304

R8385

R8386

R8387

R8352

TP8302

TP8305

TP8301

TP8102

TP8310

P

P

P

P

R8301

0

R8323

220

R8334

47

R8319

10k

R8302 47

R8328

100

R8335

47

R8332

47

R8313

0

R8315

220

R83090

R8303 47

R8318

1k

R8324

2.2

k

R8310

0

R8330

47

R8300

0

R83120

R8327

47k

R8338

47k

R8350

47k

R8321

2.2

k

R8326

10k

R8316

470

TU8300ENG36F12KF

NC

1

BB2

RF-AGC_Monitor

3

NC

5BT_Monitor

6

VB10

Video-out11

SCL13

SDA14

AFT-OUT15

IF_AGC16

+B17

IFD-out119

IFD-out220

NC

8SIF-out

9

H0J250500079X8300

25MHz

IF_OUT_P

IF_OUT_N

3.3V

1.2V

38 39 40 41 37 42

! TUNER

FRONT ENDPROCESSOR

TUNER

FE1.2V

!



52/119

52


Th

erm

alPad

PWM_WO_R-

PWM_WO_L+

PWM_WO_L-

PWM_WO_R+

PWM_WO_L+

PWM_WO_L-

PWM_WO_R+

AMP_MUTE

PWM_WO_R-

C230016V0.1u

C2305

25V1u

C234550V

0.022u

C2365

10u

25V

C2333

25V

0.33u

C2377

50V0.022u

C238150V

0.022u

C233950V

0.022u

C239025V1u

C2319

0.1u

50V

C2375

50V0.022u

C2317

0.1u50V

C2321

0.1u

50V

C2337

50V0.022u

C237950V

0.022u

C2364

10u25V

C2347

50V0.022u

C2323

0.1u

50V

C238

50V1000p

C236925V1u

C2367

25V1u

C2341

25V

0.33u

C2335

25V

0.33u

C230116V

0.1u

C2343

25V

0.33u

C1AB00003230

IC2301

1 STBY 44PVD1

2 MUTE

3 SOS

4 NC1

5 NC2

6 NC3

7 NC4

8 PWM_A1

9 PWM_B1

10 NC5

11 NC6

12 NC7

13 GND

14 PWM_B2

15 PWM_A2

16 NC8

17 NC9

18 NC10

19 NC11

20 NC12

21 NC13

22 NC14 23

PVD2

24

PVD2

25OUT_CH2_P

26

OUT_CH2_P

27

BOOT_CH2_P

28VDDA2

29

BOOT_CH2_N

30

OUT_CH2_N

31

OUT_CH2_N

32

PGND2

33PGND2

34

PGND1

35

PGND1

36OUT_CH1_N

37

OUT_CH1_N

38

BOOT_CH1_N

39

VDDA1

40

BOOT_CH1_P

41OUT_CH1_P

42

OUT_CH1_P

43

PVD1

L2001

J0JYC0000070

L2019

J0JHC0000045

L2018

J0JHC0000045

L2016

G1C220MA0416

L2010

G1C220MA0416

L2014

G1C220MA0416

L2012

G1C220MA0416

SUB3.3V

SOUND15V

SUB3.3V

SOUND15VR

TP2008

PD_APWMSRP

AMP_MUTE

PD_APWMSLN

PD_MUTEB

PD_NSHUTDOWN

PD_APWMSRN

PD_APWMSLP

AG_SOUND_SOS

Q2300B1ADCE000022

R2326

EXB28V220JX

R21233.3

R2331220

R2303

2.2k

R2308

1k

R2330

3.9k

R2121

3.3

R2306

47k

10k

R2301

R21273.3

R2307

4.7k

R21253.3

R23022.2k

JS2005

0

RESET

PEAKS-LDA2

PWM_READY

OPERATE

MUTE

SOS

OPERATE

System(Dchip)

GenX8

OPERATE

SOS

47 50 46 49 48 51

AUDIO AMP!

TO 15/18

AUDIO AMP

TO 9/18

TO 7/18

TO 15/18

TO 15/18



53/119


54/119

54


+

Th

erm

alP

ad

P

P

P

P

P

PC5420

1u16V

C5418

1u25V

C5651

4.7u10V

C5652

4.7u

6.3V

C565010V2.2u

C564910V

1u

C2848

1u

25V

C5617

2.2u10V

C5618

0.01u25V

C5767

10u

25V

C5764

22u

6.3V

C5770

0.1u16V

C5773

22u

6.3V

C5769

0.1u

25V

C5765

22u

6.3V

C5771

0.015u16V

C5788

25V

10u

C5789

10u

25V

C910825V

0.01u

C5794

1000p50V

C5255

1u10V

C5256

1u10V

C284725V

47u

D5620

B0JCPG000030

D5605B0HCMM000014

D5619

B0JCCE000008

D5618

B0JCCE000008

D5573

B0BC01100001

D5602

DZ2J056M0L

C0CBCBC00227

IC5251

1

ON/OFF

2

VSS

3

NC

5

VIN

4

VOUT

C0DBFYY00049

IC56031

VIN

2

VSS

3

CE

5

VOUT

4

NC

C0DBAGF00030

IC5604

1

ON/OFF

2

VSS

3

NC

5

VOUT

4

VINC0DBGYY00884

IC5401

VOUT 3

2

VSS

VIN

1

IC5607C0DBAYY00755

1 BOOT

2 VIN

3 SW

4 GND 5

FB

6

COMP

7

EN

8

SS

Thermal_Pad

L2754

J0JHC0000075

L5742

G1C220MA0416

SUB3.3V

F15VSUB3.3V

SUB9V

SUB5V

F15V

SUB3.3V

SUB5V_USB

DCDCIN

SUB5V_TUNER

VDDSD

AVDDH

DCDCIN

SOUND15V

F15V

ACHIP3.3V

SUB5V

SUB_AI_3.3VSUB5V

P15V

SUB5V

F15V

SOUND15VR

VJ3500

VJ5453

R3500

VJ5510

VJ5451

VJ5509

PA5601

K5H5022A0031

TP3522

TP5602

TP3508

TP5

TP5605

TP35

TP5604

TP9196

TP5600

TP5505

TP5601

T P5 50 6 T P5 50 4

TP9200

TP350

TP3521

TP

TP3507

TP8852

TP5292 TP5293

TP3506

PD_SDVOLC

DCDCEN

Q5603DSC2001S0L

Q5602DSC2001S0L

R5640

10k

R5807

2.2

R5800

10k

R561210k

R5799

47k

R5801

6.8k

R3570

0

R5643

10k

R5642

100k

R564110k

R56447.5k

R5600

68

R560722k

R561047k

R560910k

R885647k

R5608

68k

R5805

15

R561347k

R5611

2.2k

R5809

6.2k

LDA2 DC/DC DC/DC SOS

65 68 64 67 66 69

POWER!

SUB9V

SUB5V

SUB_AI_303V

AVDDH

ACHIP3.3V

TO 15/18

TO 17/18



55/119

55


+S

P

C5614

16V0.1u

C5612

10V

1u

C5630

16V0.1u

C5611

10V1u

C5629

16V0.1u

C5631

16V0.1u

C5368

1u10V

C5387

1u

10VC5391

1u

10V

C5378

10V1u

C5380

0.1u16V

C5369

1u

10V

C5390

0.1u

16V

C5375

1u10V

C5389

1u

10V

C5367

1u10V

C5381

0.1u

16V

C5377

0.1u

16V

C5376

1u

10V

C537010V1u

C5382

1u10V

C5388

0.1u

16V

C5374

1u10V

C5372

0.1u

16V

C5383

1u

10V

C5385

0.1u

16V

C5386

1u10V

C5373

0.1u16V

C5653

50V

1000p

C5703

16V 0.1u

C5615

100u16V

D2660

B0HCMM000014

D2659

B0ACCJ000048

C1ZBZ0004161

IC5480

1 UHZ

2 P3.3V

3 TEST

4 PANEL_SOS

5 DRVRST_PD4

6 STB1.2V

7 STB5V

8 STB3.3V

9 AMUTE

10 SP_MUTE

11 MUTE_VCC

12 AUDIO_MUTE_IN

13 DTB9V

14 MONITOR_MUTE

15 FB

16 GND 17FC

18

PGND

19

DRV

20DTV5VOUT

21

DTV5VIN

22

EN_DCDC

23

CD

24

STB_RST

25DRVRST

26

STB5V_SW_ON

27

P_SOS4

28SC_SOS6

29

SC_SOS7

30

SS_SOS8

31

D_SOS_RSV

32

SC_OHZ

SUB9V

STB5V

SUB5V

STB3.3V

SUB3.3V

P3.3V

SUB5V

SUB5V

SUB9V

SUB3.3V

STB5V

STB3.3V

R5489

VJ3707

TP5489

TP5493

TP4701

TP5492

MON_MUTE

SOS4_PS

SOS8_SS

SOS7_SC2

SC_UHZ

SP_HP_MUTE

AG_PD4H_DRVRST

SOS6_SC1

AG_KEY3

SOS_DCC

PD4H_DRVRST

KEY3

AG_PANEL_SOS

AMP_MUTE

D_UHZ

Q2266DSC200100L

Q5684B1ADCE000022

R54814.7k

R5457

56

R5651

68k

R564810k

R553420k

R2265

10k

R2264

10k

R5652

100k

R553310k

R5650

47k

R2310

100

R548715

PA_HP_MUTE

GenX8

STB-MPU

MUTE

Peaks

PD4H_SOS-RESERVE

D block

76 75 78 74 77 73

Analog ASIC

POWER!

TO 10/18

TO 8/18

ANALOG ASIC

STB3.3VSTB_RESET

TO 6/18

TO 7/18

TO 12/18

TO 7/18

TO 7/18

TO 15/18



56/119


57/119

57


S

GENX_SDA

PEAKS_SDA0

PEAKS_SCL0

GENX_SDA

PEAKS_SCL1

PEAKS_SDA1

GENX_SCL

PEAKS_SDA0

PEAKS_SCL0

PEAKS_SCL2

PEAKS_SDA2

PEAKS_SCL2

PEAKS_SDA2

GENX_SCL

PEAKS_SCL1

PEAKS_SDA1

A18

1

2

3

4

5

6

7

8

9

10

11

A17

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

STB5V

STB5V

R4151

ZA1001

K4AZ01D00004 ZA1002

K4AZ01D00004

ZA1005

K4CC01000001

ZA1004

K4CC01000001

ZA1003

K4CC01000001

TP8526

TP8537

TP8527

TP8525

TP8529

TP8530

TP8505

TP8503

TP8501

TP8538

TP8528

TP8524

TP8536

TP8522

TP8500

TP8521

TP8535

TP8523

PEAKS_SCL1

PEAKS_SCL0

PEAKS_SCL2

AG_SRQ-GENX

FACT_SDBOOT

GENX_SCL

PD_SBI0

PEAKS_SDA2

PEAKS_SDA1

PD_SBO0

PEAKS_SDA0

GENX_SDA

R4131

EXB28V220JX

R4171

22

R417022

R412622

R412722

R412522

R412822

(INEXCH)

GenX SDA1Panel_RXD

(DeviceControl)

(DeviceControl)

GenXSCL1

Peaks_SDA2

Peaks SCL0

Peaks SDA0

(PANEL LED)

SRQ-GENX

IIC_CONT

Panel_TXD

GND (10/4)

(DeviceControl)

(DeviceControl)

(DeviceControl)

GenX8

(PANEL REM_CON)

STB5V

GND

(DeviceControl)

Peaks_SCL2

STB5V

GenX8

IIC

IIC1

IIC0

IIC2

PEAKS_SBO0

PEAKS_SBI0

PeaksSCL1

PeaksSDA1

(Peaks_SCL2)

(Peaks_SDA2)

SD_BOOT_MODE

GenX8

Peaks_SDA2

Peaks_SCL2

SRQ-GENX

IIC_CONT

93 95 96 92 9491

!

FORFACTORYUSE

FORFACTORYUSE

TO 15/18

TO 7/18

TO 7/18

TO 7/18

TO 2,12/18

TO 1,2,7/18

TO 2,5,10/18

CONNECTOR

JS

TP4000

S

JS

S

T

T



58/119


59/119


60/119


61/119


62/119

62


+

16VC8022

0.1u

C8057

10V

1u

C807516V

0.1u

C8065

16V0.1u

C8036

10V

1u

C803516V

0.1u

C8027

10V

1u

C801816V

0.1u

C807216V

0.1u

16V

0.1u

C8062

C8030

16V

0.1u

C8017

10u

10V

C80836.3V

4.7u

C8048

16V

0.1u

0.1u

16VC8037

C801116V

0.1u

C8042

16V

0.1u

C8068

16V

0.1u

C803816V

0.1u

C8090

16V0.1u

C807916V

0.1u

C8033

16V

0.1u

C804416V

0.1u

C801916V

0.1u

C8074

16V0.1u

C8025

0.1u

16V

C808410V

10u

16VC8046

0.1u

C8043

0.1u

16V

C807016V

0.1u

C8051

10V

1u

C805016V

0.1u

C80586.3V

4.7u

C808916V

0.1u

0.1u

16VC8052

C802316V

0.1u

C805616V

0.1u

0.1u

16VC8049

C806716V

0.1u

C805316V

0.1u

C800416V

0.1u

C8078

16V0.1u

C800010V

10u

C8008

10u10V

C8054

10V

1u

C800510V

10u

C8082

10u

10V

0.1u

16VC8034

C8094

16V0.1u

C807116V

0.1u

0.1u

16VC8010

C8024

16V

0.1u

C80606.3V

4.7u

C8085

10V10u

C8015

10u

10V

C8087

16V0.1u

C8039

16V

0.1u

C8091

16V0.1u

C801316V

0.1u

16VC8016

0.1u

C806316V

0.1u

C808816V

0.1u

C802916V

0.1u

0.1u

16VC8055

C8009

10u

10V

0.1u

16VC8028

C80596.3V

4.7u

C8096

16V0.1u

C800110V

10u

C8006

10u

10VC8077

16V

0.1u

C800310V

10u

C8020

0.1u

16V

0.1u

16VC8040

C801216V

0.1u

C807616V

0.1u

C806916V

0.1u

C802116V

0.1u

16VC8066

0.1u

C8073

16V

0.1u

C8092

16V0.1u

C8061

10V10u

C806410V1u

0.1u

16VC8031

C8045

10V

1u

C8002

68u

4V

L8006

J0JCC0000287

L8009

J0JHC0000045

L8003

J0JHC0000045

L8024

J0JCC0000287

L8008

J0JCC0000287

L8014

J0JCC0000287

L8013

J0JCC0000287

L8007

J0JHC0000045

L8010

J0JCC0000287

L8001

J0JCC0000287

J0JCC0000287

L8004

J0JKC0000021

L8012

J0JCC0000287

L8005

J0JKC0000021

L8000

J0JCC0000287

L8011

J0JHC0000116

SUB3

SUB1.2V_D

SUB1.2V_ASUB3.3V

DDR1.5VSUB1.5V

SUB3.3V

VDDSD

SUB1.2V

SUB3.3V

PD_AVDDPLL1_2

PD_VDDAUSB

PD_VDD12

PD_VDDSD

PD_VDDPUSB

PD_DAAVDD1

PD_VDD33

PD_LVVDD12

PD_AVDDPLL0_3

PD_LVVDD33

PD_VDDUSB

PD_VDDR

PD_VDDIOCK

PD_VDDA

PD_AVDDPWM

R8031

4.7k

PEAKS-LDA2 Dchip PEAKS

140136 137 138 141 139

!

TO 15/18

TO 15/18

TO 15/18

TO 15/18

TO 3,15/18

TO 15/18

TO 15/18

TO 15/18

LOCK_LDA2-POWERA-BOARD (16/18)TXN/A1MGUUS (TC-P50G20)TXN/A1LPUUS (TC-P50G25)


63/119

63


S

S

S

S

S

S

S

S

C5538

22u

6.3V

C552325V

10u

C5503

1u16V

C5532

22u

6.3V

C5529

22u

6.3V

C5531

22u

6.3V

C552225V10u

C5535

22u

6.3V

C5528

22u

6.3V

C5506

1u16V

C5507

0.039u10V

C5521

25V10u

C5537

22u

6.3V

C5500

6800p25V

C5502

4.7u10V

C5530

22u

6.3VC55054.7u10V

C5517

10u

25V

C5519

10u

25V

C5536

22u

6.3V

C5526

25V

10u

C5539

22u6.3V

C5534

22u

6.3V

C5516

10u25V

C5520

25V10u

C5533

22u

6.3V

C5501

0.15u10V

C55046800p25V

C5510

0.1u16V

C5508

0.1u16V

C5509

0.1u16V

C5511

0.1u

16V

D5505

B0JCPD000026

C0DBAYY00715

IC5501

1 DRVH1

2 VBST1

3 EN1

4 VO1

5 VFB1

6 GND

7 SS1

8 VFB2

9 VO2

10 EN2

11 VBST2

panasonic tc-p50g20 tc-p50g25 chassis gpf13du

Documents