panasonic tc-65ps14 ch gpf12du
DESCRIPTION
service manualTRANSCRIPT
-
Panasonic Corporation 2009.Unauthorized copying and distribution is a violationof law.
ORDER NO.MTNC091064CEB34 Canada: B07
65 inch Class 1080p Plasma HDTVModel No. TC-65PS14GPF12DU Chassis
-
2TABLE OF CONTENTSPAGE PAGE
1 Safety Precautions -----------------------------------------------31.1. General Guidelines ----------------------------------------3
2 Warning --------------------------------------------------------------42.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------42.2. About lead free solder (PbF) ----------------------------5
3 Service Navigation------------------------------------------------63.1. Service Hint--------------------------------------------------63.2. Applicable signals ------------------------------------------7
4 Specifications ------------------------------------------------------85 Service Mode -------------------------------------------------------9
5.1. How to enter into Service Mode ------------------------95.2. Service tool mode---------------------------------------- 115.3. Hotel mode------------------------------------------------- 12
6 Troubleshooting Guide---------------------------------------- 136.1. Check of the IIC bus lines------------------------------ 136.2. Power LED Blinking timing chart --------------------- 146.3. No Power--------------------------------------------------- 156.4. No Picture-------------------------------------------------- 166.5. Local screen failure -------------------------------------- 17
7 Service Fixture & Tools --------------------------------------- 187.1. SC jig -------------------------------------------------------- 18
8 Disassembly and Assembly Instructions --------------- 198.1. Remove the Rear cover -------------------------------- 198.2. Remove the Fan------------------------------------------ 198.3. Remove the P-Board------------------------------------ 198.4. Remove the Side terminal cover and Rear
terminal cover --------------------------------------------- 208.5. Remove the Tuner unit --------------------------------- 208.6. Remove the A-Board------------------------------------ 208.7. Remove the Speakers ---------------------------------- 218.8. Remove the Control button unit ---------------------- 218.9. Remove the GK-Board --------------------------------- 21
8.10. Remove the SU-Board---------------------------------- 218.11. Remove the SD-Board---------------------------------- 228.12. Remove the SC-Board---------------------------------- 228.13. Remove the SS2-Board -------------------------------- 228.14. Remove the SS3-Board -------------------------------- 238.15. Remove the SS-Board---------------------------------- 238.16. Remove the Support metal (C) ----------------------- 238.17. Remove the Support metals (L, R) ------------------ 238.18. Remove the Vertical bar-down assy----------------- 248.19. Remove the C1-Board ---------------------------------- 248.20. Remove the C2-Board ---------------------------------- 248.21. Remove the C3-Board ---------------------------------- 258.22. Remove the Plasma panel section from the
Cabinet assy (glass)------------------------------------- 258.23. Remove the Glass holders ---------------------------- 258.24. Remove the Rear cover fix holders------------------ 268.25. Remove the S-Board------------------------------------ 268.26. Remove the K-Board------------------------------------ 278.27. Replace the plasma panel ----------------------------- 27
9 Measurements and Adjustments -------------------------- 289.1. Adjustment Procedure ---------------------------------- 289.2. Adjustment ------------------------------------------------- 31
10 Block Diagram --------------------------------------------------- 3310.1. Main Block Diagram ------------------------------------- 3310.2. Block (1/4) Diagram ------------------------------------- 34
10.3. Block (2/4) Diagram------------------------------------- 3510.4. Block (3/4) Diagram------------------------------------- 3610.5. Block (4/4) Diagram------------------------------------- 37
11 Wiring Connection Diagram -------------------------------- 3911.1. Caution statement. -------------------------------------- 3911.2. Wiring (1) -------------------------------------------------- 3911.3. Wiring (2) -------------------------------------------------- 4011.4. Wiring (3) -------------------------------------------------- 4111.5. Wiring (4) -------------------------------------------------- 42
12 Schematic Diagram -------------------------------------------- 4312.1. Schematic Diagram Note ------------------------------ 4312.2. P(MULTI)-Board Schematic Diagram--------------- 4412.3. P(SUS)-Board Schematic Diagram ----------------- 4512.4. GK, K and S-Board Schematic Diagram----------- 4612.5. A-Board (1/15) Schematic Diagram----------------- 4712.6. A-Board (2/15) Schematic Diagram----------------- 4812.7. A-Board (3/15) Schematic Diagram----------------- 4912.8. A-Board (4/15) Schematic Diagram----------------- 5012.9. A-Board (5/15) Schematic Diagram----------------- 51
12.10. A-Board (6/15) Schematic Diagram----------------- 5212.11. A-Board (7/15) Schematic Diagram----------------- 5312.12. A-Board (8/15) Schematic Diagram----------------- 5412.13. A-Board (9/15) Schematic Diagram----------------- 5512.14. A-Board (10/15) Schematic Diagram --------------- 5612.15. A-Board (11/15) Schematic Diagram --------------- 5712.16. A-Board (12/15) Schematic Diagram --------------- 5812.17. A-Board (13/15) Schematic Diagram --------------- 5912.18. A-Board (14/15) Schematic Diagram --------------- 6012.19. A-Board (15/15) Schematic Diagram --------------- 6112.20. C1-Board (1/2) Schematic Diagram ---------------- 6212.21. C1-Board (2/2) Schematic Diagram ---------------- 6312.22. C2-Board (1/2) Schematic Diagram ---------------- 6412.23. C2-Board (2/2) Schematic Diagram ---------------- 6512.24. C3-Board (1/2) Schematic Diagram ---------------- 6612.25. C3-Board (2/2) Schematic Diagram ---------------- 6712.26. SC-Board (1/4) Schematic Diagram ---------------- 6812.27. SC-Board (2/4) Schematic Diagram ---------------- 6912.28. SC-Board (3/4) Schematic Diagram ---------------- 7012.29. SC-Board (4/4) Schematic Diagram ---------------- 7112.30. SS-Board (1/2) Schematic Diagram ---------------- 7212.31. SS-Board (2/2), SS2-Board and SS3-Board
Schematic Diagram ------------------------------------- 7313 Printed Circuit Board------------------------------------------ 74
13.1. P(MULTI)-Board------------------------------------------ 7413.2. P(SUS)-Board -------------------------------------------- 7713.3. GK, K and S-Board-------------------------------------- 7913.4. A-Board ---------------------------------------------------- 8013.5. C1-Board--------------------------------------------------- 8213.6. C2-Board--------------------------------------------------- 8313.7. C3-Board--------------------------------------------------- 8413.8. SC-Board -------------------------------------------------- 8513.9. SS-Board -------------------------------------------------- 87
13.10. SS2 and SS3-Board ------------------------------------ 8914 Exploded View and Replacement Parts List----------- 91
14.1. Exploded View and Mechanical ReplacementParts List --------------------------------------------------- 91
14.2. Electrical Replacement Parts List ------------------- 97
-
31 Safety Precautions1.1. General Guidelines
1. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.2. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or some of the
wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the entire wiring unit instead.3. When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug them straight
out.4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or
damaged by the short circuit.5. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly
installed.6. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1. Leakage Current Cold Check1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metal-lic cabinet part on the equipment such as screwheads,connectors, control shafts, etc. When the exposed metal-lic part has a return path to the chassis, the readingshould be between 1Mohm and 5.2Mohm.When the exposed metal does not have a return path to the chassis, the reading must be .
1.1.2. Leakage Current Hot Check (SeeFigure 1.)
1. Plug the AC cord directly into the AC outlet. Do not usean isolation transformer for this check.
2. Connect a 1.5kohm, 10 watts resistor, in parallel with a0.15F capacitors, between each exposed metallic parton the set and a good earth ground such as a water pipe,as shown in Figure 1.
3. Use an AC voltmeter, with 1000 ohms/volt or more sensi-tivity, to measure the potential across the resistor.
4. Check each exposed metallic part, and measure the volt-age at each point.
5. Reverse the AC plug in the AC outlet and repeat each ofthe above measurements.
6. The potential at any point should not exceed 0.75 voltsRMS. A leakage current tester (Simpson Model 229 orequivalent) may be used to make the hot checks, leakagecurrent must not exceed 1/2 milliamp. In case a measure-ment is outside of the limits specified, there is a possibilityof a shock hazard, and the equipment should be repairedand rechecked before it is returned to the customer.
Figure 1
-
42 Warning2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors andsemiconductor [chip] components. The following techniques should be used to help reduce the incidence of component damagecaused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD protected)] can
generate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.Caution
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion such as the brush-
ing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficientto damage an ES device).
-
52.2. About lead free solder (PbF)Note: Lead is listed as (Pb) in the periodic table of elements.In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
This model uses Pb Free solder in its manufacture due to environmental conservation issues. For service and repair work, wedsuggest the use of Pb free solder as well, although Pb solder may be used.
PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.Caution
Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 F (30~40 C) higher. Pleaseuse a high temperature soldering iron and set it to 700 20 F (370 10 C).
Pb free solder will tend to splash when heated too high (about 1100 F or 600 C).If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb sol-der. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.
After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto theopposite side. (see figure below)
Suggested Pb free solderThere are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. How-ever, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.
-
63 Service Navigation3.1. Service Hint
Board Name Function Board Name FunctionP Power Supply SC Scan DriveA DC-DC Converter, Tuner
Speaker out, AV Terminal, AV SwitchDigital Signal Processor, SYSTEM MPU, HDMI SwitchSeine 3LVFormat Converter, Plasma AI, Sub-Field Processor
SS Sustain DriveSS2 Sustain out (Upper)SS3 Sustain out (Lower)SU Scan out (Upper)
Non-serviceable.SU-Board should be exchanged for service.K Remote receiver, Power LED, C.A.T.S sensor
S Power Switch SD Scan out (Lower)Non-serviceable.SD-Board should be exchanged for service.
GK Key SwitchC1 Data Driver (Lower Right)C2 Data Driver (Lower Center)C3 Data Driver (Lower Left)
-
73.2. Applicable signals* Mark: Applicable input signal for Component (Y, PB, PR) and HDMI
Note Signals other than those shown above may not be displayed properly. The above signals are reformatted for optimal viewing on your display.
horizontal frequency (kHz) vertical frequency (Hz) COMPONENT HDMI525 (480) / 60i 15.73 59.94 * *525 (480) /60p 31.47 59.94 * *750 (720) /60p 45.00 59.94 * *1,125 (1,080) /60i 33.75 59.94 * *1,125 (1,080)/60p 67.43 59.94 *1,125 (1,080)/60p 67.50 60.00 *1,125(1,080)/24p 26.97 23.98 *1,125(1,080)/24p 27.00 24.00 *
-
84 Specifications
Power Source AC 120 V, 60 Hz Power Consumption
Maximum 724 W Standby condition 0.3 W
Plasma Display panelDrive method AC type Aspect Ratio 16:9Visible screen size 65 inch class (64.7 inches measured diagonally)(W H Diagonal) 56.4 inch 31.7 inch 64.7 inch (1,434 mm 806 mm 1,645 mm)(No. of pixels) 2,073,600 (1,920 (W) 1,080 (H))[5,760 1,080 dots]
SoundAudio Output 20 W [ 10 W + 10 W ] ( 10 % THD )
Channel Capability (Digital/Analog) VHF/ UHF: 2 - 69, CATV: 1 - 135 Operating Conditions
Temperature: 32 F - 104 F (0 C - 40 C)Humidity: 20 % - 80 % RH (non-condensing)
Connection TerminalsVIDEO IN 1 VIDEO: RCA PIN Type 1 1.0 V [p-p] (75 )
S-VIDEO: Mini DIN 4-pin Y: 1.0 V [p-p] (75 ) C: 0.286 V [p-p] (75 )AUDIO L-R: RCA PIN Type 2 0.5 V [rms]
VIDEO IN 2 VIDEO: RCA PIN Type 1 1.0 V [p-p] (75 )AUDIO L-R: RCA PIN Type 2 0.5 V [rms]
COMPONENT INPUT 1-2 Y: 1.0 V [p-p] (including synchronization)PB, PR: 0.35 V [p-p]AUDIO L-R: RCA PIN Type 2 0.5 V [rms]
HDMI 1-3 TYPE A Connector 3This TV supports [HDAVI Control 4] function.
Card slot SD CARD slot 1 DIGITAL AUDIO OUT PCM / Dolby Digital, Fiber Optic
FEATURES 3D Y/C FILTERCLOSED CAPTION V-ChipPhoto Viewer HDAVI Control 4
Dimensions (W H D)Including pedestal 62.0 inch 40.0 inch 16.4 inch (1,574 mm 1,016 mm 415 mm)TV Set only 62.0inch 38.0 inch 2.6 inch (4.1 inch) (1,574 mm 965 mm 66 mm (104 mm))
MassIncluding pedestal 145.6 lb. (66.0 kg) TV Set only 132.3 lb. (60.0 kg)
Note Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
-
95 Service Mode5.1. How to enter into Service Mode
While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
5.1.1. Key command [1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward direction [4] button...Sub items Selection in reverse direction [VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
-
10
5.1.2. Contents of adjustment mode Value is shown as a hexadecimal number. Preset value differs depending on models. After entering the adjustment mode, take note of the value in each item before starting adjustment.
5.1.3. How to exitSwitch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Main item Sub item Sample Data RemarkADJUST CONTRAST 46
COLOR 00TINT 00SUB-BRT 000
WB-ADJ R-CUT 80G-CUT 80B-CUT 80R-DRV FCG-DRV FFB-DRV E8ALL-CUT 80ALL-DRV FC
OPTION BOOT ROM Factory PresetSTBY-SET - -EMERGENCY ONCLK MODE 00HPD reset Enable
AGING RGBWVERTICAL LINECOUNT ALL WHITEALL REDALL GREENALL BLUEON/OFFRAMP WHITERAMP REDRAMP GREENRAMP BLUE1% WINDOWCOLOR BARA-ZONE B-ZONE/4 TRIOSCROLLWHITE FLAMELOW SETUP REDLOW SETUP GREENLOW SETUP BLUE
RM-SET CODE A Fixed
SRV-TOOL - See next
-
11
5.2. Service tool mode5.2.1. How to access
1. Select [SRV-TOOL] in Service Mode.2. Press [OK] button on the remote control.
5.2.2. Display of SOS HistorySOS History (Number of LED blinking) indication.From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory ship-ment setting].
5.2.3. POWER ON TIME/COUNTNote : To display TIME/COUNT menu, highlight position, then press MUTE for (3sec). Time : Cumulative power on time, indicated hour : minute by decimalCount : Number of ON times by decimalNote : This indication will not be cleared by either of the self-checks or any other command.
5.2.4. Exit1. Disconnect the AC cord from wall outlet.
-
12
5.3. Hotel mode1. Purpose
Restrict a function for hotels.2. Access command to the Hotel mode setup menu
In order to display the Hotel mode setup menu, pleaseenter the following command (within 2 second). [TV] : Vol. [Down] + [REMOTE] : INPUT (3 times)
Then, the Hotel mode setup menu is displayed.
3. To exit the Hotel mode setup menu Disconnect AC power cord from wall outlet.
4. Explain the Hotel mode setup menu
item FunctionMode Select hotel mode ON/OFFInput Select input signal modes.
Set the input, when each time power isswitched on.Selection:-/ANTENNA/COMP1/COMP2/HDMI1/HDMI2/HDMI3/VIDEO1/VIDEO2
Off: give priority to a last memory. Channel Select channel when input signal is RF.
Set the channel, each time power is switchedon.Selection: Any channel number or [-]. [-] means the channel when turns off.
Volume Adjust the volume when each time power isswitched on.Range: 0 to 100
Vol. Max Adjust maximum volume.Range: 0 to 100
OSD Ctrl Restrict the OSD.Selection:OFF/PATTERN1
OFF: No restriction PATTERN1: restriction
FP Ctrl Select front key conditions.Selection: Off/All/Pattern1
Off: altogether valid. All: altogether invalid. Pattern: only input key is valid.
Pow Ctrl Select POWER-ON/OFF condition when ACpower cord is disconnected and then con-nected. OFF: The same condition when AC powercord is disconnected. ON: Forced power ON condition.
-
13
6 Troubleshooting GuideUse the self-check function to test the unit.
1. Checking the IIC bus lines2. Power LED Blinking timing
6.1. Check of the IIC bus lines6.1.1. How to accessSelf-check indication only:Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote controlfor more than 3 seconds.Self-check indication and forced to factory shipment setting:Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote con-trol for more than 3 seconds.
6.1.2. ExitDisconnect the AC cord from wall outlet.
6.1.3. Screen display
6.1.4. Check PointConfirm the following parts if NG was displayed.
-
14
6.2. Power LED Blinking timing chart1. Subject
Information of LED Flashing timing chart.2. Contents
When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, thedefective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
-
15
6.3. No PowerFirst check pointThere are following 2 states of No Power indication by power LED.
1. No lit2. Red is lit then turns red blinking a few seconds later. (See 6.2.)
-
16
6.4. No Picture
-
17
6.5. Local screen failurePlasma display may have local area failure on the screen. Fig-1 is the possible defect P.C.B. for each local area.
Fig-1
-
18
7 Service Fixture & Tools7.1. SC jigPurpose:To find the failure board (SC or SU/SD) when the power LED is blinking 7 times.SC jig:Jumper connector to connect to SC50 connector on SC boardPart number:TZSC09187How to use:Caution: Remove SC jig from SC board after inspection.
1. Remove all connector between SC board and SU/SD board to isolate SC board from both SU and SD board electrically.Note: The board will be damaged if all connector is not removed (for example; remove connector only for SU board and stayconnecting with SD board. The board will be damaged.)
2. Connect SC jig to connector SC50 at left bottom side of SC board3. Turn of the TV/Display Unit and confirm the power LED blinking.
LED blinking: Possible cause of failure is in SC boardNo LED blinking (Lighting or no lighting): Possible cause of failure is in SU or SD board
4. After inspection, turn off the TV/Display Unit and wait a few minutes to discharge.5. Remove SC jig from SC board.
Remark: This SC jig can be used for all 2009 Plasma TV and Plasma Display.
-
19
8 Disassembly and Assembly Instructions8.1. Remove the Rear cover
1. See Service Hint (Section 3)
8.2. Remove the Fan1. Unlock the cable clampers to free the cable.2. Remove the screws (3 ).3. Remove the relay connectors and remove the Fan unit.
4. Remove the screws (2 ) on the back side.5. Remove the Fan.
8.3. Remove the P-BoardCaution:
To remove P.C.B. wait 1 minute after power was off for dis-charge from electrolysis capacitors.1. Unlock the cable clampers to free the cable2. Disconnect the connectors (P51-P52, P53-P54 and P55-
P56).3. Disconnect the connectors (P2, P6, P7, P9, P11, P25 and
P35).4. Remove a short-jumper connector P34 and re-use for
new P-Board.5. Remove the screws (6 ) and remove the P(SUS)-
Board.6. Remove the screws (9 ) and remove the P(MULTI)-
Board.
-
20
8.4. Remove the Side terminalcover and Rear terminal cover
1. Remove the claw (1 ).2. Remove the Side terminal cover.
3. Remove the Adjustment cover.4. Remove the screws (4 , 3 ).5. Remove the Rear terminal cover.
8.5. Remove the Tuner unit1. Unlock the cable clampers to free the cable.2. Disconnect the connectors (A1, A6 A11, A12, A25 and
A30).3. Disconnect the flexible cables (A31, A32 and A33).4. Remove the screws (2 , 1 ) and remove the
Tuner unit.
8.6. Remove the A-Board1. Remove the Tuner unit. (See section 8.5.)2. Remove the screws (4 ) and remove the A-Board.
-
21
8.7. Remove the Speakers1. Unlock the cable clampers to free the cable.2. Disconnect the Speaker terminal. 3. Remove the screws (2 ) and remove the Speakers
(L, R).
8.8. Remove the Control button unit1. Disconnect the connector (C14).2. Remove the screws (2 ).3. Remove the Control button unit.
8.9. Remove the GK-Board1. Remove the Control button unit. (See section 8.8.)2. Remove the screws (2 ).3. Remove the GK-Board MTG. metal.
4. Remove the claw (3 ).5. Disconnect the connector (GK1).6. Remove the GK-Board from Control button.
8.10. Remove the SU-Board1. Remove the flexible cables (SU1, SU2, SU3, SU4 and
SU5) connected to the SU-Board.2. Remove the flexible cable (SU11-SD11) and the bridge
connector (SC41-SU41).3. Remove the molding props (3 ).4. Remove the screws (3 , 3 ) and remove the SU-
Board.
-
22
8.11. Remove the SD-Board1. Remove the Control button unit. (See section 8.8.)2. Remove the flexible cables (SD1, SD2, SD3, SD4 and
SD5) connected to the SD-Board.3. Remove the flexible cable (SU11-SD11) and the bridge
connectors (SC42-SD42 and SC46-SD46).4. Remove the molding props (3 ).5. Remove the screws (3 , 3 ) and remove the SD-
Board.
8.12. Remove the SC-Board1. Remove the SU-Board and SD-Board. (See section 8.10.
and 8.11.)2. Unlock the cable clampers to free the cable.3. Disconnect the connector (SC2).4. Disconnect the flexible cable (SC20).5. Remove the screws (9 ) and remove the SC-Board.
8.13. Remove the SS2-Board1. Disconnect the bridge connector (SS02-SS24A) and dis-
connect the flexible cable (SS52).2. Remove the screws (2 ) and remove the SS2-Board.
-
23
8.14. Remove the SS3-Board1. Remove the Tuner unit. (See section 8.5.)2. Disconnect the bridge connector (SS03-SS22) and dis-
connect the flexible cables (SS57 and SS59).3. Remove the screws (4 ) and remove the SS3-Board.
8.15. Remove the SS-Board1. Remove the Tuner unit. (See section 8.5.)2. Unlock the cable clampers to free the cable.3. Disconnect the connectors (SS11 and SS33).4. Disconnect the flexible cables (SS53, SS55 and SS56).5. Disconnect the bridge connectors (SS02-SS24A and
SS03-SS22).6. Remove the screws (6 ) and remove the SS-Board.
8.16. Remove the Support metal (C)1. Remove the screws (4 , 2 ).2. Remove the Support metal (C).
3. Remove the screws (2 ).4. Remove the Shield metals (L, R).
8.17. Remove the Support metals (L,R)
1. Remove the Tuner unit. (See section 8.5.)2. Remove the screws (2 , 1 each).3. Remove the Support metals (L, R).
-
24
8.18. Remove the Vertical bar-downassy
1. Remove the Plasma panel section from the servicingstand and lay on a flat surface such as a table (coveredby a soft cloth) with the Plasma panel surface facingdownward.
2. Remove the Support metal (C). (See section 8.16.)3. Remove the screws (2 , 2 each) and remove the
Vertical bar-down assy (L, R).4. Remove the screws (4 each) and remove the V-bar
connecting metal-top (L, R).5. Remove the screws (2 ) and remove the V-bar fixing
metals (L, R).
6. Remove the screws (2 each) and remove V-bar con-necting metal-bottom (L, R) and the Bracket covers (L,R).
8.19. Remove the C1-Board1. Remove the Control button unit. (See section 8.8.)2. Remove the Support metal (C). (See section 8.16.)3. Remove the Support metal (R). (See section 8.17.)4. Remove the Vertical bar-down assy. (See section 8.18.)5. Remove the flexible cables holder fastening screws (10
).6. Disconnect the flexible cables (CB1, CB2, CB3, CB4 and
CB5).7. Disconnect the flexible cable (C10).8. Disconnect the connector (C14).9. Remove the screws (5 ) and remove the C1-Board.
8.20. Remove the C2-Board1. Remove the Support metal (C). (See section 8.16.)2. Remove the flexible cables holder fastening screws (10
).3. Disconnect the flexible cables (CB6, CB7, CB8, CB9 and
CB10).4. Disconnect the flexible cables (C20, C21 and C26).5. Remove the screws (5 ) and remove the C2-Board.
-
25
8.21. Remove the C3-Board1. Remove the Tuner unit. (See section 8.5.)2. Remove the Support metal (C). (See section 8.16.)3. Remove the Support metal (L). (See section 8.17.)4. Remove the Vertical bar-down assy. (See section 8.18.)5. Remove the flexible cables holder fastening screws (10
).6. Disconnect the flexible cables (CB11, CB12, CB13, CB14
and CB15).7. Disconnect the flexible cables (C31 and C36).8. Disconnect the connectors (C33 and C35).9. Remove the screws (5 ) and remove the C3-Board.
8.22. Remove the Plasma panel sec-tion from the Cabinet assy (glass)
1. Remove the cabinet assy and the plasma panel fasteningscrews (12 , 4 ).
2. For leaving the plasma panel from the front frame, pull thebottom of the cabinet assy forward, lift, and remove.
8.23. Remove the Glass holders1. Remove the Cabinet assy. (See section 8.22.)2. Unlock the cable clampers to free the cable.3. Remove the screws (4 , 4 ).4. Remove the Joint metal top (4) and the Joint metal bot-
tom (4).
5. Remove the screws (4 ).6. Remove the Glass holder bottom.7. Remove the screws (2 ).8. Remove the Glass holder top.9. Remove the screws (8 ).
10. Remove the Glass holders (L, R).
-
26
8.24. Remove the Rear cover fixholders
1. Remove the Glass holders. (See section 8.23.)2. Remove the screw (1 each).3. Remove the Rear cover fix holders (L, R).
8.25. Remove the S-Board1. Remove the Glass holder bottom. (See section 8.21.)2. Remove the screws (2 ) and remove the S-Board
unit.
3. Disconnect the connector (S2).4. Remove the Power button.5. Remove the claw (1 ) and remove the S-Board.
-
27
8.26. Remove the K-Board1. Remove the Glass holder bottom. (See section 8.23.)2. Remove the screws (2 ).3. Remove the claw (1 ).4. Disconnect the connector (K1) and remove the K-Board
from LED Panel.
8.27. Replace the plasma panelCaution:
A new plasma panel itself without Hanger metals isfragile.To avoid the damage to new plasma panel, carry a newplasma panel taking hold of the Hanger metals afterassembling the Hanger metals and the Stand brackets.
1. Place a carton box packed a new plasma panel on the flatsurface of the work bench.
2. Open a box and without taking a new plasma panel;Attach the C1-Board, C2-Board and the C3-Board, con-nect the flexible cables from the plasma panel to the C1-Board, C2-Board and the C3-Board, and fit the flexiblecable holders.
3. Attach the Hanger metals and the Stand brackets to thenew plasma panel.
4. Place the plasma panel on the servicing stand taking holdof the Hanger metals.
5. Attach the cabinet assy and each P.C.Board and so on, tothe new plasma panel.
*When fitting the cabinet assy, be careful not to allow any debris, dust or handling residue to remain between the front glass and plasma panel.
-
28
9 Measurements and Adjustments9.1. Adjustment Procedure9.1.1. Driver Set-up9.1.1.1. Item / Preparation
1. Input a white signal to plasma video input.2. Set the picture controls as follows.
Picture menu: VividNormal: SetAspect: Full
Caution1. First perform Vsus adjustment.2. The Vscn voltages are measured from the Vad (Vad_base), but may be measured from the GND (GND_base) in an
unavoidable case.
9.1.1.2. AdjustmentsAdjust driver section voltages referring the panel data on the panel data label.Check or adjust the following voltages with the multimeter.
*See the Panel label.
Name Test Point Voltage Volume RemarksVsus TPVSUS (SS) Vsus 2V VR251 (P) *Ve TPVE (SS) Ve 2.5V Fixed *Vset TPVSET (SC) 290V 9V FixedVad TPVAD (SC) - 155V 2V VR16600 (SC)Vscn TPVSCN (SC) Vad_base : 145V 4V
GND_base : - 10V 6VFixed
-
29
9.1.2. Initialization Pulse Adjust 1. Input the White signal to plasma video input.2. Set the picture controls as follows.
Picture menu : VividNormal : SetAspect : Full
3. Connect Oscilloscope to TPSC1 (SC).Check the voltage (T2) at 100s period on the down slop.
9.1.3. P.C.B. (Printed Circuit Board) exchange9.1.3.1. Caution
1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.
9.1.3.2. Quick adjustment after P.C.B. exchangeAdjust the following voltages with the multimeter.
*See the Panel label.Caution:
Absolutely do not reduce Vsus below Ve not to damage the P.C.B.
Test point Volume LevelT2 TPSC1 (SC) VR16601 (SC) 250 V 10 V
P.C.B. Name Test Point Voltage Volume RemarksP Board Vsus TPVSUS (SS) Vsus 2V VR251 (P) *SC Board Vad TPVAD (SC) - 155V 2V VR16600 (SC)A Board White balance and Sub brightness for NTSC, PAL, HD, PC and 625i signals
-
30
9.1.4. Adjustment Volume Location
9.1.5. Test Point Location
-
31
9.2. Adjustment9.2.1. White balance adjustment
Name of measuring instrument Connection Remarks W/B pattern Color analyzer
(Minolta CA-100 or equivalent) Note: The CA-100 which was calibrated to less than+ - 0.001 with CS-1000.
Component inputor HDMI inputor ATSC 1080i signalPanel surface
Procedure Remarks Make sure the front panel to be used on the final set is fitted. Make sure a color signal is not being shown before adjustment. Put the color analyzer where there is little color variation.
1. Set the Picture menu to [vivid] and output the THX pattern.
2. Check that the color temperature is [Cool].3. Set to serviceman mode, WB-ADJ.4. Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1. 5. Attach the sensor of color analyzer to the center of highlight window.6. Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer
become the [Color temperature High] in table 2.7. Increase RGB together so the maximum drive value in RGB becomes FC. That is,
set [ALL DRIVE] to FC.Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC,and either R/G/B DRV should be FC.
8. Set color temperature to [Normal].9. Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1.
10. Attach the sensor of color analyzer to the center of highlight window.11. Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer
become the [Color temperature Mid] in table 2.12. Increase RGB together so the maximum drive value in RGB becomes FC. That is,
set [ALL DRIVE] to FC.Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC,and either R/G/B DRV should be FC.
13. Set color temperature to [Warm].14. Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1. 15. Attach the sensor of color analyzer to the center of highlight window.16. Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer
become the [Color temperature Low] in table 2.17. Increase RGB together so the maximum drive value in RGB becomes FC. That is,
set [ALL DRIVE] to FC.Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC,and either R/G/B DRV should be FC.
18. Set color temperature to [Cool].
-
32
-
33
10 Block Diagram10.1. Main Block Diagram
(LED:6TIMES)
(LED:7TIMES)
(LED:8TIME)
(LED:4TIME)
HOTCOLD
(LED:7TIMES)
(LED:3TIMES)
(LED:10TIMES)
(LED:5TIMES)
(LED:4TIMES)
(LED:6TIMES)
(LED:2TIMES)
(LED:8TIMES)
(LED:10TIMES)
P2
SUSTAINVOLTAGERECTIFIER
VSUS
C35
SCAN OUT (UPPER)
C20Vda
DATADRIVER
C1
DATADRIVER
DATADRIVER
DATADRIVER
DATADRIVER
SOS7_SC2
Vda
C21
DATADRIVER
SD11
+
3
.
3
V
(
P
)
SS33
DATADRIVER
SS22
+
3
.
3
V
(
P
)
DATA DRIVER (RIGHT)
SS11
SC41
CONTROLPULSE
SCANDRIVER
DATADRIVER
+
5
V
(
P
)
KEYSCAN1
VSET GEN.
STB5V
KEY SWITCH
DATADRIVER
POWERFACTORCONTROL
SOS8_SS
S
O
S
8
_
S
S
BUFFER
Vda
VSUS
F15V
SS03
RELAY
+15V(P)
SCAN DRIVE
RECTIFIER
VIDEO DATA
C21
P51
SD
P56
KEYSCAN1
V
I
D
E
O
D
A
T
A
S
U
S
T
A
I
N
C
O
N
T
R
O
L
MULTI
SC-BOARDFLOATING PARTSOS DETECT
VAD GEN.
C10
SUS
SU
SC2
POWERFACTORCONTROL
SD46
+15V(P)
V
I
D
E
O
D
A
T
A
RELAY
DATADRIVER
VIDEO DATA
P52
SS
SC42
SC
SC-BOARDENERGY RECOVERYSOS DETECT
+5V(P)
VSUS
SD42
VSUSSC46
VSCAN GEN.
DATADRIVER
SS-BOARDSOS DETECT
VSUS GEN.
SU11
+
5
V
(
P
)
DATADRIVER
GK
SUSTAIN CONTROL
SU41
V
d
a
ENERGY RECOVERY
P25
P
Vda
C33
POWER MICOM
DATADRIVER
SUSTAIN DRIVE
POWER SUPPLY
C14
SS02
+15V(P)
C2
+
1
5
V
(
P
)
SS24A
ON/OFF CONTROL
+
1
5
V
(
P
)
C26
SS2
+5V(P)SOS6_SC1
C36
STB5V
CONNECTOR
P11
+
3
.
3
V
(
P
)
GK1
P55
(UPPER)
DATADRIVER
+
5
V
(
P
)
SUSTAIN
MAIN SW2
C31
CONNECTOR
PS SOS4
+
5
V
(
P
)
+3.3V,+5V(P)
(LOWER)
RECTIFIER
V
d
a
SOS8_SS
SUSTAINP34
+
3
.
3
V
(
P
)
SUSTAIN CONTROL
SS3
RECTIFIER
SCANDRIVER
SCAN CONTROL
VIDEO DATA
STANDBYVOLTAGERECTIFIER
VE GEN.
AC CORD
VIDEO DATA
PROCESSVOLTAGERECTIFIER
KEY SWITCH
P6
F15V
K
E
Y
S
C
A
N
1
P7
SCAN OUT (LOWER)
+5V(P)
SC20
+15V(P)
DATADRIVER
+15V(P)
DATA DRIVER (CENTER)
MAIN SW1
DATA DRIVER (LEFT)
VSUS
C3
P-BOARDSOS DETECT
P9
SOUND15V
P35
PANEL STB_ON
BT30V
V
Seine3LV
DCDC
PANELMAIN ON
HDMI1
DDR2
(SIDE)
SOUND
C.A.T.S. SENSOR
Y,PB,PR
MEMORY
TUNER SOS
AUDIO
SUB9V
SD CARD DATA
A12
SCAN CONTROL
VIDEO DATA
COMP2
+5V(P)
+
3
.
3
V
(
P
)
+3.3V(P)
A25
OPTICAL AUDIO OUT
V
PANEL MICOM
SD CARD DATA
TUNER
BT30V
SWITCH
FLASH
A11
IIC1
SUB+9V DET
A1 REMOTE RECEIVER
L
COMP1
(SIDE)
+5V(P)
+15V(P)
+1.8V(P)
PANEL SOS
DCDC
F15V
SOS6_SC1
AUDIO SW
SUB5V
SUB3.3V
L,R
POWER SOS
L,R
EEPROM
BT30V
+3.3V(P)
+3.3V(STB)
SUB1.3V
ON
L,RKEYSCAN3
REMOTE RECEIVER
S POWER SWITCH
+15V(P)
SDIN
L
V
D
S
D
A
T
A
+2.5V(P)
VIDEO2
VIDEO1
+1.2V(P)
SUB+5V DET
+15V(P) DET
SUB9V
DISCHARGECONTROL
L,R
SOS7_SC2
SUB9V
TUNER SOS DETCIRCUIT
A/D
+3.3V(P)
DIGITAL SIGNAL PROCESSOR
S
O
U
N
D
1
5
V
SBO2SBI2
SUB5V
VIDEO SW
LED(R)
PLASMA AICPG with SSH/V Sync ControlSub Filed ProcessorPlasma AI
A31
R,G,B
SOS6_SC1
HDMI3
LVDS DATA
SUB3.3V
HDMI SW
+3.3V(P) DET
C.A.T.S. SENSOR
SUB9V
PANEL STATUS
V,Y,C
+2.5V(P)
CONTROLSIGNAL
TUNER SOS
SUSTAINCONTROL
+5V(P)
K
STB3.3V
SUB+3.3V DET +3.3V(S)
HDMI2 HDMI DATA
SPEAKER(R)
SLOT
DCDC
F15V
L,R
VSB_IN
SOS7_SC2
A
DCDC
SD
TMDS DATA
SUB1.8V
R
TMDS DATA
IFD_OUT
A33
C.A.T.S. SENSOR
Y,PB,PR
+3.3V(STB)
DCDC
L,R
S2
OUT
SD
+5V(P) DET
DCDC
KEYSCAN1
RESET
REMOTE IN
POWER LED(R)
SPEAKER(L)
POWER LED
PD3-H
K1
HDMI DATA
+1.2V(P)
KEYSCAN1
SOS8_SS
+5V(S)
POWER
STB3.3V
R,G,B
EEPROM
STB5V
+5V(P)
OPTICAL OUT
+15V(P)
TMDS DATA
AUDIO
SD CARD
DDR
SUB1.8V
DCDC
PANEL STATUS
RESET
+1.8V(P)
PANEL STB_ON
OPTICAL
+15V(P)
AMP
+9V(S)
SUB1.3V
S
T
B
5
V
SD0
PANEL SOS
SYSTEM MPU
F
1
5
V
SUB5V
A6
SUB5V
STB_D3.3V
STB_D3.3VDCDCSTB5V_M
A32
+
5
V
(
P
)
+
3
.
3
V
(
P
)
S
O
S
8
_
S
S
VIDEO DATA
(LED:6TIMES)
(LED:7TIMES)
(LED:8TIME)
(LED:4TIME)
HOTCOLD
(LED:7TIMES)
(LED:3TIMES)
(LED:10TIMES)
(LED:5TIMES)
(LED:4TIMES)
(LED:6TIMES)
(LED:2TIMES)
(LED:8TIMES)
(LED:10TIMES)
-
34
10.2. Block (1/4) Diagram
(LED:10TIMES)
(LED:11TIMES)
BT30V
P
A
5
6
0
1
STB5V
SUB3.3V
STB3.3V
Q5604
HDMI_3.3V
SUB3.3V
D5521
SUB1.8V
D5522
BT30V
SUB9V
SOUND15V
D5613
SUB1.3V
SUB9V
D5692
Q5603
D5614
SUB2.5V
F15V
SUB9V
SUB5V
SUB5V
STB5V
Q5522
L5442L5441 D5484
D5485
SUB5V
D5615
D5750
D5749
TPF0S
STB5V
SBI2
IC5607
D1_Y
SBO2
IIC1_EEP
VIDEO2
IC8003
2
F15V DET
+
5
V
(
H
D
M
I
)
HDMI DATA
0.9V
4
9
ON/OFF
Q
4
5
3
0
SUB9V
6
1
S
O
U
N
D
1
5
V
IC8502
IC4508
SUB5V
VIDEO1
IC5608
Q
4
5
3
1
Q
4
5
2
9
D
E
T
_
3
T
M
D
S
D
A
T
A
C
L
O
C
K
D
E
T
_
2
TV SUB ON
JK4502
COMP2
D5486
EEPROM
DRV
+
5
V
(
H
D
M
I
)
5
1.3V
D
E
T
_
1
IC2107
37
L/R
F15V
F
1
5
V
PC_HS/VSOUT
AUDIOI/F
DROPERROR DET
HS/VS
BT30V
S
T
B
5
V
Y/PB/PR
3
EEPROM
TV
1
A12
SDIN
H
D
M
I
_
C
E
C
A11
+9V
IC8007
RX1
L/R
2.5V
V2
STB_RESET
SUB5V
VIDEO1
SUB3.3V
V2_R
L(+)
L(-)
L/R
VIDEO
V1
R(+)
F
1
5
V
SUB1.3V
P7
DDC_IIC
D1
P6
AUDIO
IIC1_EEP
JK3701
IF_AGC
IIC0
(SIDE)
HDMI_IN
IIC1
SDIN
LVDS_OUT
SYS_IIC0
TV_R
R/G/B_IN
TV_LANT IN
+5V(HDMI)DET 1,2,3
DDR2 #0
+
5
V
(
H
D
M
I
)
D
E
T
1
,
2
,
3
BT30V
IC8002
JK4501
5V2.5V
IFD_OUT2
8
AFT
F15V
V2_L
SUB9V
V2_V
14
VIDEO2
SUB1.8V
COMP2
COMP1
DDR I/F
DIGITAL SIGNAL PROCESSOR
R/G/B
RESET
STB3.3V
IFD_OUT1
AFT
KEYSCAN3
DTV RESET
DDC3_IIC
SUB9V
IC8004
SYS_IIC2_TU
V
D1
TV_V
COMP1
SUB5V
D2
S
O
U
N
D
1
5
V
SD CARD
IC5606
SUB3.3V
SOUND15V
L/R
JK8302
AUDIO
IF_AGC
V1_R
D
D
C
I
I
C
D3005
DTV1
D1_L
OPTICAL
9V
DDC1_IIC
L/R
DTV2
DTV5V
IC4501
D2
+1.3V
D1_R
CPU BUSI/F
+1.8V
D2_Y
VIDEO3
+3.3V
EEPROM
+5V
V1
IC4500
IC8008
SDO
BT30V
MAIN L/R
IC8503
D2_PB
V2
R/G/B
Y/PB/PR
SPEAKER
D2_PR
13
SPDIF
H
D
M
I
_
C
E
C
SOUND A/D
IC2109
IIC_IF
TUNER SOS
OUT
SPEAKER_R
L/R
A6
D2_L L/R
STB
VOLTAGE
D2_R
+
5
V
(
H
D
M
I
)
RESET
H
D
M
I
_
C
E
C
DDC2_IIC
RX3
DTV1
IC5480
T
M
D
S
D
A
T
A
C
L
O
C
K
3.3V
RX2
EEPROM
3.3V
COMP2
HS/VS
VIDEO SW
Y/C/V
HS/VS
STB+3.3V
SYS_IIC0
PC_HS/VS
PC
JK3000VIDEO4
V1_L
VIDEO1
D
D
C
I
I
C
5V
1
Y/C
(SIDE)
V1_C
COMP1
3.3V
A
VIDEO2
1
2
HDMI IN 1
+
5
V
F
1
5
V
VIDEO3
3
RGB_CVBS
+
5
V
S
O
U
N
D
1
5
V
2
HDMI IN 3
+
5
V
T
V
S
U
B
O
N
D1_PR
D
D
C
I
I
C
PC
SUB5V
HDMI IN 2
H
D
M
I
_
C
E
C
VIDEO4
HDMI SW
STB3.3V
V1_V
R/G/B/H/V
Y/PB/PR
L/R
MUTE
AUDIO AMP
SD CARDI/F
TV
IC4503
+15V
D1_PB L/R
L_OUT
V1_Y
R(-)
T
M
D
S
D
A
T
A
C
L
O
C
K
TV
Y/C
LVDS DATA
L/R
T
V
_
V
I
D
E
O
3.3V
AUDIO SW
V
STB_RESET
CLOCK GEN
L/R
1.8V
MAINOUT
ANALOG ASIC
SPEAKER_L
CLOCK
SUBOUT
SPEAKER
RESET
Seine3LV
SUB MONOL+R
JK4500
IC8001
R_OUT
DDC_IIC
TV
IIC0
SD DATA:4bit
SOS DET
+9/7.2V
D5745D5746D5747D5748
FAN D OVERVOLTAGE
3
A30
FAN AFAN STOP
FAN A-D
1
FAN SOS
FAN MAX
PANEL MAIN ON
LVDS DATA
HDMI DATA
CLK BUFFER
IC8009
IC3001
VSB_I/F
VINP_VSB
VINN_VSB
TU8300
TUNER
DDRVREF
IC5401
OPTICAL AUDIO OUT
IC5740
F15VFAN CONT.
NOR FLASH
(LED:10TIMES)
(LED:11TIMES)
-
35
10.3. Block (2/4) Diagram
(LED:6TIMES)
(LED:8TIMES)
(LED:4TIMES)
(LED:5TIMES)
(LED:10TIMES)
(LED:3TIMES)
(LED:7TIMES)
(LED:2TIMES)
(LED:11TIMES)
P15V
STB3.3V
P3.3V
P5V
D2520
P1.2V
Q1105
P1.8V
STB5V_M
P3.3V
STB_D3.3V
P1.8V
STB3.3V
SUB5V
3
IC9808
PANEL SOS
IIC1
PANEL STATUS
+2.5V
PANEL STB_ON
9
KEYSCAN3
4
POWER LED
6
C.A.T.S.
POWER SWITCH
A1
5
2
IIC3
1.2V
CONTROL DATA
FLASH I/F
2.5V
DDR2
IC9300
CONTROL DATA
5
C21
+1.2V
1
SUB9V
45
K
SUB5V
A32
+15V(P) DET
ADDR/DATA
+5V(P)
PD3-H
+5V(P)
2
TV SUB ON
SUSTAIN CONTROL
AND
PANEL SOS
SOS7_SC2
60
IC1102
STB+3.3V/RESET
FLASHMEMORY
6
HDMI_CEC
+3.3V(P)
63
SOS6_SC1
PANEL STATUS
68
SC20
1
TUNER SOS
2
AUX_ON/OFF
SOS6_SC1
XRST,XRSTSYS
A31
POWER SWITCH
VIDEO DATA10
SCAN CONTROL
STB RESET
DTV RESET
S
REMOTE IN
K
E
Y
S
C
A
N
3
RESET
STB RESET
+15V(P)
+5V(P)
FORFACTORYUSE
IIC2
2
IIC1
CONTROL DATA
+15V(P)
STB_D3.3V
IIC0
9 STB5V
A
SOS7_SC2
+3.3V(P) DET
DIGITAL SIGNAL PROCESSOR
RESET
15
A17
+5V(P)
+15V(P)
A18
PANEL SOS
12
PANEL STATUS
PANEL SOS
STB+3.3V
KEYSCAN1
HDMI_CEC_OUT
6
IC9807
29
6
IC9001
+3.3V
14
1
3
SUSTAIN CONTROL
*PLASMA AI*CPG with SS*H/V Sync Control*Sub Filed Processor*Plasma AI
2
GenX7
IC9902,03
Config(DONE)
KEYSCAN1
STB3.3V
SUB3.3V
UHZ
IC9004
+15V(P)
SUB9V DET
VIDEO DATA
+3.3V(P)
SOS8_SS
IC9303
SOS8_SS
DISCHARGE CONTROL
5
PANEL MAIN ON
C31
Config(CCLK,DDTATA,PROGB),FPCLK,FPDATA[1:0],FVSEL
IIC2
3
+1.8V
66
SOS4_PS
1
IIC2
IC9806
VIDEO DATA
1
SCAN CONTROL
68
REMOTE IN
1
ON
POWER LED(R)
TUNER SOS
TEMP SENSOR
IC1100
IC4800
TV SUB ON
SUB3.3V DET
A25HDMI_CEC_PU_ON
A33
66
5
+5V(P) DET
VIDEO DATA
3
POWER ON/OFF
1
.
2
V
UHZ
DTV RESET
3.3V
17
REMOTE RECEIVER
P25
IC9003
10
PANEL_MAIN_ON
K1
11
OSD I/F
SW2500
S2
POWER SOS
FORFACTORYUSE
IIC2
PANEL STATUS
PANEL STB_ON
DDR I/F
SUB+5V
KEYSCAN3
1
.
8
V
O
S
D
I
/
F
30
POWER LED
Config(DONE)
+3.3V(P)
PANEL STB_ON
DRVRSTFPGARSTXRST
C.A.T.S. SENSOR
3
.
3
V
AI SENSOR
TV_VIDEO
8 KEYSCAN3
TV_VIDEO
8
IC9805
PANEL MICOM
EEPROM
SUB5V DET
K1
+3.3V
STB3.3V
R_LED_ON
1
LVDS DATA
LVDS DATA
P
A
N
E
L
M
A
I
N
O
N
SYSTEM MPU
IC9500
FAN SOS
FAN MAXFAN SOS
FAN MAX
AFTAFT
IIC0
SYS_IIC0
IIC1_EEP
IIC2SYS_IIC2_TU
IIC1EEPROM
IC1101
SBO2SBI2
REMOTERECEIVER
PC2501
RM2501
C.A.T.S.SENSOR
(LED:6TIMES)
(LED:8TIMES)
(LED:4TIMES)
(LED:5TIMES)
(LED:10TIMES)
(LED:3TIMES)
(LED:7TIMES)
(LED:2TIMES)
(LED:11TIMES)
-
36
10.4. Block (3/4) Diagram
COLD
COLD
(LED:4TIMES)
HOT COLD
HOT
HOT
F501
D352
F802
F301
D551
D402
F801
D505
F201
F602F601
D500
D206
MC501
A6
P9
9
Vsus_OUT
P
BIAS1_ON
A
L
L
_
O
F
F
6
PC201
2
NEUTRAL
Vsus
IC501
P6
LIVE
P2
A25
3
Vsus
Vda
11
POWER SUPPLY
2A 250V
A6
T501
L802
1
Q403
STBERROR DET
IC352
+
1
5
V
(
S
N
D
)
MC701
PHOTO COUPLER
BIAS1_ON
PC301
3
Q351
RF801
1
MULTIPOWERCONTROL
IC301
Vda
RESONANCE
Q301,Q3025A 250V
VR401
Vda
PC302
PHOTO COUPLER
Vsus_ON
V
d
a
_
O
N
M
A
I
N
R
E
L
A
Y
1
_
O
N
15V
POWER SOS
+5V(P)
+5V(P)
+5V
SOS4_PS
Q601-Q604
MC451
PANEL_MAIN_ON
5
V
_
O
N
VsusPOWERCONTROL
+
5
V
(
P
)
Q551
P34
R
U
S
H
R
E
L
A
Y
1
_
O
N
7
L603,L605
TV SUB ON
LIVE
T201
P7
PHOTO COUPLER
PANEL_MAIN_ON
NEUTRAL
CONTROL
6
+15V(P)
AC DET
AC CORD
PHOTO COUPLER
S
T
B
_
O
N
+
1
5
V
(
P
)
IC601
RECTIFIER
SS11
VsusERROR DET
ALL_OFF
MAIN RELAY2
1
PHOTO COUPLER
T
V
S
U
B
O
N
RUSH RELAY1
+5V(STB)
STB
1
5
V
_
O
U
T
D254-D257
1
RECTIFIER
PHOTO COUPLER
53
PC202
D401 MC401
Q401
T301
1
5
V
_
O
N
PHOTOCOUPLER
Q353
Q402
M
U
L
T
I
_
O
N
VdaCONTROL
PC401
+15VERROR DET
BIAS1(+)
S
T
B
_
O
U
T
LIVE
NEUTRAL
K803
2
Q201,Q202
+15V(P)
IC555
+15V(P)
F
S
T
B
+
1
5
V
C35
Q605-Q608
+
1
5
V
(
P
)
+15V(P)
+
5
V
Vsus
VR251
+
5
V
(
S
T
B
)
10A 250V
V
d
a
_
O
U
T
FILTER
12
+5V(P)
+5V(STB)
8
RESONANCE 1
10A 250V
D501
1
1
1 10
Vda
IC251 4IC201
PC501
F
S
T
B
+
1
5
V
9
M
A
I
N
S
W
_
O
N
F
S
T
B
+
1
5
V
P11
Vsus
2
5
D806
P35
A
C
D
E
T
+
1
5
V
(
S
N
D
)
P25
K801
K802
PFC CONTROL
+
1
5
V
(
S
N
D
)
SC2
POWER MICOM
5A 250V
PHOTO COUPLER
PC231
PC502
BIAS2_ON
P55 5 4
5 4P56
1
1
7
7
V
s
u
s
_
O
U
T
Vsus_ON
BIAS2_ON
+15V(P)
P52 6 5
1 2P51
2 1
5 6
PFC CONTROL
Q802,Q803
MC801
L805Q801
Q502
K603
K602
MAIN RELAY2NEUTRAL
RUSH RELAY2
LIVE
RF601
K601
RECTIFIER
D601,602
10A 250V10A 250V
BIAS2(+)
L602FILTER
L601
R
U
S
H
R
E
L
A
Y
2
_
O
N
M
A
I
N
R
E
L
A
Y
2
_
O
N
Q611
2
2
P53
P54
L
I
V
E
L
I
V
E
N
E
U
T
R
A
L
N
E
U
T
R
A
L
MULTI
SUS
NEUTRAL
LIVE
COMPARATOR
IC202
15V_OCL
Q354
+5V(P)
Q203
Q303
COLD
COLD
(LED:4TIMES)
HOT COLD
HOT
HOT
-
37
10.5. Block (4/4) Diagram
(LED:8TIMES)
(LED:6TIMES)
(LED:7TIMES)
TPVSCN
D16253
VR16601
5V
TPSOS6
TPVE
TPSOS7
VF_GND
5V
TPVSUS
D16821
TPSOS8
TPVAD
D16901
D16480
D16725
D16791
D16255
D16493
D16721
D16820
D16473
TPSS1
D16280 TPSC1
VR16600
D16282
TPVSUS
D16583
TPVSET
ERROR DETDROP
30
SEL
CPH2
P35
D16051
SUSTAIN DRIVE
A33
CB4
USH
UEH
KEYSCAN1
4
CRC1
3
VHIZ
ERROR DET
SCANCONTROL
IC17302
Vsus
SHUNT
UML
68
REG.DRIVER
PC16480
55
CML
12
COMPARATOR
9
1
BUFFER
C20
CONNECTOR
SD
1CSL
+5V(P)
59
Vfo
22
CB5
1
CIRCUIT
CB15
SOS6_SC1
1
SCAN OUT (UPPER)
5
DRIVER
+5V(P)
8
CB7
USL
Q16818
SHUNT
DATA DRIVER (LEFT)
IC14955-58
UEH
UHZ
ENERGY
+5V
CEL
52
USL Q16051
VHIZ GEN.
IC16131
CB11
OC1
Vda
CEL
SOS8_SS
(15V_F)
SD46
V
I
D
E
O
D
A
T
A
A32
GK
PLASMA PANEL
KEY SWITCH
MAIN_STOP
Q16608
ERROR DET
BUFFER
CERS
44
Vda
V
I
D
E
O
D
A
T
A
1
IC16691
15V_F
1
VSET23
4
IC16792IC16793
BUFFER
Q16661
UMH
PLASMA PANEL
S
U
S
T
A
I
N
C
O
N
T
R
O
L
NAND GATE
UML
8
ELECTRODE
OC2
GEN.USH
+
3
.
3
V
(
P
)
(SC1)
SS11
CML
SHUNT REG
DATA DRIVER (CENTER)
+
3
.
3
V
(
P
)
CONTROL DATA
IPD CIRCUIT
(LOWER)
4
SEL
SC46
SU
DATA DRIVER (RIGHT) A31
SEPA PROTECT
SOS8_SS
SS33
OC1
4
Q16101
REG.
3
DRIVER
PANEL DRIVER
IC16304
IC16490,91
IC16920
CLK
C1
D16053
VOLTAGE
C33
12
IPD CIRCUIT
(INIT-F)
SC42
IC16561,62
K
E
Y
S
C
A
N
1
2
SUSTAIN CONTROL
IC16724
Q16052
VIDEO DATA
IC17301
IC16725
41
+
5
V
(
P
)
SS3
D16041
+5V(P)
FPC DET
CSH
53
IC14951-54SC20
1
CB14
SU1-SU5
LED(G)
CERSCLK
SU41
BUFFER
1
IC16564IC16801
8
1
D16860
VHIZ
(VAD)
VE GEN.
15
DRIVERSC41
CB13
25
6
CB8
13
IC16312
D16859
VSCN
55
SUSTAIN
S
O
S
8
_
S
S
4
SC50
SD1-SD5
CB10
C
O
N
T
R
O
L
D
A
T
A
COMPARATOR
CRC1
2
ERROR DET
SCAN CONTROL
V
I
D
E
O
D
A
T
A
Q16042
CB2
SD11
VscnQ16876
C10
SS
PANEL SUSTAIN
SCAN
Vda
DRIVER
Q16280
SS33
C35
Q16041
4
CRC2
IC16784
D16871
66
IC16786,87
SCAN
SCNR_PRO
SUSTAIN CONTROL
+5V(P)
IC14961-65
PANEL DRIVER
SU11
CB1
SOS7_SC2
C31
IC14901-04
DRIVER
PANEL SCAN
OC2
PC16301
13
IPD CIRCUIT
VSUS Gen.
VSET23
P11
3
RECOVERY
V
I
D
E
O
D
A
T
A
CB9
IC16563
CMH
2
IC16692
1
(SC2)
C33
GK1
CB12
CSL
SCNR_PRO
+
3
.
3
V
(
P
)
VSCN GEN.
CIS
PANEL DRIVER
12
55
CPH1
3
CB3
C2
IC14905-08
SUSTAIN CONTROL
LOGIC IC
+5V
35
1
+15V
24
19
KEY SWITCH
VE Gen.
2
KEYSCAN1
21 5
6
Q16490
SS53
PHOTO COUPLER
PLASMA PANEL
15V_F
IC16661
IC16251
1 6
2
IC16151
IC16241
8
F_5V_B
2
Vda
1
9
SIU
F_5V_A
PC16191
1 C21
9
C3
2
SCAN OUT (LOWER)
D16043
INVERTER
CRC2
C
O
N
T
R
O
L
D
A
T
A
SS56 VSCN-F
ELECTRODES
SD42
BUFFER
IC17201
SCAN
UHZ
SCAN
C14
Q16102
SIU
PHOTOCOUPLER
VSET23GEN.
CB6
Vfo
VAD
UMH
FORFACTORYUSE
13
13
SS59
1
2
1
SS57
2
234SS22
9 81SS24A
234SS03
(UPPER)
SS2
CONNECTOR
SUSTAIN1
81SS02
SS52
13
2
9
5
+3.3V(P)
301
26
6VIDEO DATA
Vda
25
C26
Vda
12
C36
19
650
27 4
+5V(P)51 5
+3.3V(P)328
SS55
2
13
1
IPD CIRCUIT
IC16788,89
VSET GEN.SHUNT REG
SC
Q16621
IC16771
6
CPH1
16V-F
CONVERTER
CSH
PC16685
DC/DC
PHOTO
Q16607
CERS
IC16581
VOL
COUPLER
PC16461
PC16603
P2
IC16521
Q16601
Vad+5V
+15V(P)
SCAN DRIVE
CIS
PHOTO COUPLER
PHOTO COUPLER
IC16791
CML
PC16684
CSH/CMH GATEDRIVE CIRCUIT
INVERTER
CMH
SC2
CSL
ERROR DET
1
PHOTO COUPLER
Vsus
IC16464,65
Q16623
CSL/CML GATEDRIVE CIRCUIT
IC16501
VOH
LED(G)
7
+15V(P)
Q16005
Q16025
Q16021
Q16001
IC16773
INVERTER
Q16426
Q16444
Q16454
Q16451
Q16441
Q16421
D16481
Q16401
Q16406
D16461
D16484
D16464
(LED:8TIMES)
(LED:6TIMES)
(LED:7TIMES)
-
38
-
39
11 Wiring Connection Diagram11.1. Caution statement.Caution:
Please confirm that all flexible cables are assembled correctly.Also make sure that they are locked in the connectors.Verify by giving the flexible cables a very slight pull.
11.2. Wiring (1)
-
40
11.3. Wiring (2)
-
41
11.4. Wiring (3)
-
42
11.5. Wiring (4)
-
43
12 Schematic Diagram12.1. Schematic Diagram Note
-
44
12.2. P(MULTI)-Board Schematic Diagram
E
B
4
D
731
C
5
F
2 8 96
A
Vda
Vda
CONTROL
TOA-BOARD(A6)
TOA-BOARD(A6)
TOC3-BOARD(C35)
TOA-BOARD(A25)
AC IN
TOP(SUS)-BOARD(P56)
TOP(SUS)-BOARD(P54)
TOP(SUS)-BOARD(P51)
POWER MICOM
STB CONTROL
AC DET
MULTI
CONTROL
POWER
+5V(P)
+15V ERROR DETPFC
CONTROL
STB
ERROR DET
COLDHOT
COLDHOT
COLD
HOT
COLDHOT
COLDHOT
! P(MULTI)-BOARD ETX2MM774MA
-
45
12.3. P(SUS)-Board Schematic Diagram
E
B
4
D
731
C
5
F
2 8 96
A
TOSC-BOARD(SC2)
TOSS-BOARD(SS11)
TOP(MULTI)-BOARD(P55)
TOP(MULTI)-BOARD(P52)
TOP(MULTI)-BOARD(P53)
COMPARATOR
Vsus
ERROR DET
V
s
u
s
COLDHOT
COLDHOT
Vsus POWER
CONTROL
PFC
CONTROL
! P(SUS)-BOARD ETX2MM774MG
-
46
12.4. GK, K and S-Board Schematic Diagram
VC
C
GN
D
OU
T
P
U
S
H
C2522
0.1u
16V
C25126.3V
10u
D2520
LN1271RALTR
D2512
MAZ80430LL
PC2501B3JB00000046
RM2501
B3RAD0000160
Q25102SD0601A0L
Q25112SD0601A0L
R2524
22kR2517
47
R2542
47k
R2513
5.6k
R2557
5.6k
R2525
820
R2520
220k
R2516
22k
K1 1 2 3 4 5 6 7 8 9
1
0
FL2500
J0MAB0000201
1 2
R37650
S
W
3
7
6
3
A
E
V
Q
2
3
4
0
5
R
R37721.74k
R377121k
S
W
3
7
5
9
A
E
V
Q
2
3
4
0
5
R
R3775
3.16k
R37731.62k
S
W
3
7
6
4
A
E
V
Q
2
3
4
0
5
R
S
W
3
7
6
2
A
E
V
Q
2
3
4
0
5
R
S
W
3
7
6
5
A
E
V
Q
2
3
4
0
5
R
C3752
1000p
50V
GK1 1 2
R37742.32k
S
W
3
7
6
1
A
E
V
Q
2
3
4
0
5
R
SW2500K0F122A00172
S2 1 2
REMOTE RECEIVER
C.A.T.S. SENSOR
POWER LED
G
N
D
S
T
B
3
.
3
V
S
U
B
5
V
R
M
_
I
N
G
N
D
K
E
Y
S
C
A
N
3
(
I
N
)
C
.
A
.
T
.
S
.
_
S
E
N
S
O
R
R
_
L
E
D
_
O
N
S
U
B
5
V
R
_
L
E
D
_
O
N
S
T
B
Y
3
.
3
V
C
.
A
.
T
.
S
.
S
E
N
S
O
R
R
E
M
O
C
O
N
K
E
Y
3
G
N
D
K
E
Y
S
C
A
N
3
(
O
U
T
)
K
E
Y
S
C
A
N
VOL.DN CH.DN CH.UP INPUT/OK MENU VOL.UP
G
N
D
GK-BOARD TNPA4874S!
K-BOARD TNPA4871S!
A
F
5
B
42
D
3 6 81 7
C
E
9
POWER SW
S-BOARD TNPA4873S!
TOC1-BOARD(C14)
TOA-BOARD(A1)
-
47
12.5. A-Board (1/15) Schematic Diagram
+
S
P
P
P
P
P
P
P
P
P
P
0.9V
C808150V
150p
C8116
3p
50V
C8085
50V 1500p
C8086
16V 0.1u
C8083
16V 0.1u
C8084
16V 0.1u
C8091
16V 0.1u
C8092
16V 0.1u
C8093
50V 1500p
C8094
50V5p
C8096
16V 0.1u
C8097
16V 0.1u
C8098
6.3V 1u
C8100
16V 0.1u
C8101
16V 0.1u
C8102
16V 0.1u
C8103
16V 0.1u
C8119
16V 0.1u
C8117
16V 0.1u
C8025
16V
0.1u
C8031
6.3V
1u
C8032
10u10V
C8013
16V
0.1u
C8016
6.3V
1u
C8015
6.3V
1u
C8011
16V0.1u
C8017
10u10V
C8012
16V
0.1u
C811816V0.1u
C8110
10u
10V
C81046.3V1u
C8107
50V1p
C810816V
0.1u
C8106
50V10p
C810516V
0.01u
C810916V0.1u
C8115
3p
50V
C812816V
0.1u
C812716V
0.1u
C812610V1u
C8129
50V
470p
C813010V1u
C813416V
0.1u
C8133
10u10V
C813616V0.1u
C8135
10u10V
C813216V
0.1u
C8131
10u10V
C8139
16V0.1u
C8140
16V0.1u
C8141
16V
0.1u
C8142
16V
0.1u
C8143
16V
0.1u
C8144
16V
0.1u
C814516V
0.1u
C8146
16V0.1u
C8147
16V0.1u
C8148
16V
0.1u
C8153
16V
0.1u
C8120
16V
0.1u
C8155
6.3V
1u
C8152
16V
0.1u
C8151
16V
0.1u
C8154
6.3V
1u
C8156
10u
10V
C8159
16V
0.1u
C8161
6.3V
1u
C8158
16V
0.1u
C8157
16V0.1u
C8160
6.3V
1u
C8162
10u10V
C8163
16V0.1u
C8164
10u10V
C8165
10u10V
C8166
16V
0.1u
C8167
16V
0.1u
C8087
50V 150p
C8180
2.2u6.3V
C8168
16V
0.1u
C8169
16V
0.1u
C8172
16V
0.1u
C8171
16V
0.1u
C8170
16V
0.1u
C8183
4.7u10V C8182
4.7u10V
C8179
16V0.01u
C8178
16V0.01u
C8177
16V0.01u
C8176
16V0.01u
C8175
16V0.01u
C8174
16V0.01u
C8173
16V0.01u
C809516V
0.01u
C8082
16V0.01u
C819150V
1000p
C819250V
1000p
C819350V
1000p
C8089
50V12p
C808850V10p
C8124
50V
10p
C8150
100u2.5V
D8000
MA2J11100L
D
8
0
0
2
B
0
H
C
M
M
0
0
0
0
1
4
IC8001 R2 AVDDP12
IC8001 AC7 EBADD21/NACLE
IC8001 AE6 PIO28/SCL_K
IC8001 AC1 RXN0_B
IC8001 B25 UARXD0
IC8001 R5 AVDDR
IC8001 AF21 DMADONE_N/PIO26
IC8001 C20 CLKX
IC8001 A12 TA1
IC8001 D18 TE2_N
IC8001 AC8 EBADD20
IC8001C21PIO37/PWM74CLKI
IC8001 E6 VDDC
IC8001 G5 VDDC
IC8001 AD6 PIO27/SDA_K
IC8001 AE7 EBADD23/NABSY_N
IC8001 AC2 RXP0_B
IC8001 AD7 EBADD22/NAALE
IC8001 A13 TB1
IC8001 D16 TCLK2_N
IC8001 AB1 RXNC_B
IC8001T1DAOUT1
IC8001 C22 BL0PWM
IC8001 AE5 SCL_DDC_B
IC8001 E10 VDDC
IC8001 V22 VDDDIO
IC8001 R3 BIASDA1
IC8001 AF22 SDCLK/PIO33
IC8001 B5 IRQ0
IC8001 A14 TC1
IC8001 AB2 RXPC_B
IC8001 AE21 DMAACK1/PIO25
IC8001 AF23 SDDAT0/PIO32/TSERROR
IC8001 E11 VDD33
IC8001 M1 VREFP
IC8001 H2 AVDDVSB IC8001 AF25 VDDDC
IC8001 C23 UACTS0_N/PIO8
IC8001 B22 IRBRO
IC8001 AE23 SDDAT1/PIO31/TSSYNC
IC8001 D4 VDDC
IC8001 AE4 SDA_DDC_B
IC8001 J2 P3CKIN
IC8001 F1 VINP_VSB
IC8001 AD4 SDA_DDC_A
IC8001 AB4 VDDC
IC8001 C26 DBGTCK
IC8001 U3 REXT_A
IC8001 T23 VDDDIO
IC8001 F3 IFAGC
IC8001 B24 UATXD0
IC8001 B14 TC1_N
IC8001 AD23 IRQ7/PIO4
IC8001 A17 TD1
IC8001 D5 IRQ2
IC8001 G22 VDD33
IC8001 F5 VDDC
IC8001 AF24 IRQ9/PIO6/TSCLK
IC8001 AD5 SCL_DDC_A
IC8001 U4 P2FIL
IC8001 Y2 RXP1_A
IC8001 B17 TD1_N
IC8001 J23 VDDDIO
IC8001 M3 VREFNEG
IC8001 A18 TE1
IC8001 L4 VREFDA2
IC8001 AD21 SDCD/PIO35
IC8001 Y3 TOUTP_B
IC8001 U1 TOUTP_A
IC8001 AB8 VDDC
IC8001 P22 VDDDIO
IC8001 Y23 DDRVDDA2
IC8001 C24 UARTS0_N/PIO7
IC8001 AE11 EBADD7
IC8001 A16 TCLK1
IC8001 A22 TEST
IC8001 M12 VDDC
IC8001 AC23 VDDDC
IC8001 C12 TA2
IC8001 D24 DBGTDI
IC8001 AD24 VDDDC
IC8001 P2 VREFRIN
IC8001 D17 TD2_N
IC8001 D10 UA2EXCLK/PIO15
IC8001 C5 IRQ1
IC8001 E20 VDD33
IC8001 J25 VDDDIO
IC8001 AF9 EBADD16
IC8001 U24 VDDDIO
IC8001 AD15 EBDAT5
IC8001 AB7 VDDC
IC8001 G2 VREFP_VSB
IC8001 F4 VDDC
IC8001 AC9 EBADD13
IC8001 AF17 EBCLK
IC8001 Y4 AVDD33HDMI
IC8001 B20 COLDRST_N
IC8001 D8 ASDI
IC8001 AD22 SDDAT2/PIO30/TSVALID
IC8001 M2 VREFN
IC8001 P1 VRIN
IC8001 AC22 SDDAT3/PIO29/TS0DATA7
IC8001 E9 VDDC
IC8001 T2 P12CKIN
IC8001 V4 AVDD12HDMI
IC8001 C17 TD2
IC8001 D9 UATXD2
IC8001 N2 VREFBIN
IC8001 AC21 SDWP/PIO36
IC8001 N25 VDDDIO
IC8001 B18 TE1_N
IC8001 AB6 VDDC
IC8001 AB12 VDDC
IC8001 P5 AVDD1
IC8001 M24 VDDDIO
IC8001 A10 LVOPDN
IC8001 G4 AVDDVSB
IC8001 AB11 VDDC
IC8001 K4 P3FIL
IC8001 A21 NC
IC8001 AE19 EBCE0_N
IC8001 D7 ATXO
IC8001 E19 VDDC
IC8001 B16 TCLK1_N
IC8001 AB10 VDD33
IC8001 K2 AVDDP3
IC8001 U2 TOUTN_A
IC8001 AE18 EBCE4_N/NACE_N
IC8001A20XIN27
IC8001 Y22 DDRVDDA1
IC8001 D6 PIO21/HDMI_MUTE
IC8001 AE17 EBACK_N
IC8001 AE25 VDDDC
IC8001 AF18 EBCE3_N/PIO39
IC8001 Y5 AVDD33HDMI
IC8001 M5 AVDDG
IC8001 AF16 EBDAT0
IC8001 F25 VDDDIO
IC8001 F2 PVDDVSB
IC8001 P3 SYNCIN1
IC8001 AD8 EBADD19
IC8001 AE24 IRQ8/PIO5
IC8001 L12 VDDC
IC8001 E3 RFAGC
IC8001 AC14 EBDAT11
IC8001 C6 ASDO
IC8001 C1 I2CCLK0/PIO17
IC8001 AB16 VDDC
IC8001 AF10 EBADD9
IC8001 AD19 EBCE1_N/PIO41
IC8001 V2 RXPC_AIC8001 J4 AHDIN
IC8001 A7 AMCLKI
IC8001 B8 UATXD1
IC8001 E2 ANTCON
IC8001 R15 VDDC
IC8001 AE14 EBDAT9
IC8001 AC13 EBDAT12
IC8001 J3 AVDIN
IC8001 T15 VDDC
IC8001 AB15 VDDC
IC8001 AF13 EBDAT15
IC8001 V1 RXNC_A
IC8001 A6 ALRCKO
IC8001 AC12 EBADD4
IC8001 T12 VDDC
IC8001 W26 VDDDIO
IC8001 L15 VDDC
IC8001 E23 DBGTMS
IC8001 M15 VDDC
IC8001 AB14 VDD33
IC8001 AD20 DMAACK0/PIO23
IC8001 C10 UACTS2_N/PIO14
IC8001 C16 TCLK2
IC8001 A24 XIN42
IC8001 A5 AMCLKO
IC8001 E21 VDDC
IC8001 B7 ALRCKI
IC8001 AC11 EBADD5
IC8001 AF14 EBDAT8
IC8001 AE13 EBDAT14
IC8001 AD18 EBCE5_N/NARE_N
IC8001 AE10 EBADD10
IC8001 R12 VDDC
IC8001 C9 UARXD2
IC8001 C14 TC2
IC8001 A23 XOUT42
IC8001 E18 AVDDTXBGR
IC8001 K3 BIASDA2IC8001 B6 ABCKO
IC8001 C8 UARTS1_N/PIO10
IC8001 A4 IRQ5/PIO2
IC8001 AD16 EBDAT2
IC8001 AC10 EBADD12
IC8001 AE12 EBADD2
IC8001 AF12 EBADD1
IC8001 Y1 RXN1_A
IC8001B21STCPWM
IC8001 AE2 RXP2_B
IC8001 B23 IRBCLK
IC8001 L2 VREFGIN
IC8001 A8 UARXD1
IC8001 J5 VDD33
IC8001 AA1 RXN2_A
IC8001 E15 PVDDSYS
IC8001 U5 AVDDP12
IC8001 L23 VDDDIO
IC8001 AD17 EBOE_N
IC8001 E24 DBGTRST_N
IC8001 B12 TA1_N
IC8001 AF11 EBADD8
IC8001 AB17 VDD33
IC8001 C7 ABCKI
IC8001 AE22 SDCMD/PIO34/TSREQ
IC8001 AC15 EBDAT4
IC8001 C13 TB2
IC8001 A9 UACTS1_N/PIO11
IC8001 AA2 RXP2_A
IC8001 B13 TB1_N
IC8001 K5 AVDDP3
IC8001 AC16 EBDAT3
IC8001 AE20 DMAREQ1/PIO24
IC8001 AD9 EBADD14
IC8001 V25 VDDDIO
IC8001 D22 PIO38/BL1PWM
IC8001 AA3 TOUTN_B
IC8001 AB19 VDDC
IC8001 C4 IRQ3/PIO0
IC8001 AD12 EBADD3
IC8001 AC17 EBWE_N
IC8001 AF6 HPLUG_B
IC8001 A2 XIN25
IC8001 H3 VREFN_VSB
IC8001 D11 IOVDDLVDS
IC8001 N3 VCM
IC8001 AA4 REXT_B
IC8001 AD13 EBDAT13
IC8001 AF7 ACK_DDC_B
IC8001 AE15 EBDAT6
IC8001 B9 UA1EXCLK/PIO12
IC8001 AB20 VDDC
IC8001 W1 RXN0_A
IC8001 AC18 EBCE6_N/NAWE_N
IC8001 H4 VCM_VSB
IC8001 F22 VDDC
IC8001 D12 TA2_N
IC8001 AD14 EBDAT10
IC8001 A3 XOUT25
IC8001 L1 VGIN
IC8001 AA5 VDDC
IC8001 AF8 EBADD17
IC8001 D21 VDDC
IC8001 AE16 EBDAT1
IC8001 N5 AVDDB
IC8001 D13 TB2_N
IC8001 AB21 VDDC
IC8001 D2 I2CDATA1/PIO18
IC8001 D3 I2CDATA2
IC8001 C3 I2CCLK2
IC8001 D1 I2CDATA0/PIO16
IC8001 C2 I2CCLK1/PIO19
IC8001 W2 RXP0_A
IC8001 E14 VDDC
IC8001 B10 UARTS2_N/PIO13
IC8001 AC19 EBCE2_N/PIO40
IC8001 D23 UA0EXCLK/PIO9
IC8001 H22 VDDDIO
IC8001 D14 TC2_N
IC8001 AB22 VDDDC
IC8001 AE8 EBADD18
IC8001 T3 VREFDA1
IC8001 E4 VDDC
IC8001 AC20 DMAREQ0/PIO22
IC8001 AD1 RXN1_B
IC8001 AD11 EBADD6
IC8001 D15 IOVDDLVDS
IC8001 G1 VINN_VSB
IC8001 T4 P1FIL
IC8001 N1 VBIN
IC8001 B3 IRQ6/PIO3
IC8001 E7 VDD33
IC8001 L3 VREFPOS
IC8001 AE9 EBADD15
IC8001 AB23 VDDDIO
IC8001 AF4 HPLUG_A
IC8001 AD10 EBADD11
IC8001 AF5 ACK_DDC_A
IC8001 V5 AVDD12HDMI
IC8001 E13 VDDC
IC8001 AF15 EBDAT7
IC8001 AE1 RXN2_B
IC8001 AC5 DDC5V_A
IC8001 B4 IRQ4/PIO1
IC8001 AD2 RXP1_B
IC8001 C18 TE2
IC8001 AC6 DDC5V_B
IC8001 D19 IOVDDLVDS
IC8001J1DAOUT2
IC8001 AF19 EBBE1_N/PIO42
IC8001 C25 DBGTDO
IC8001 AE26 VDDDIO
IC8001 AF20 EBBE0_N/PIO20
IC8001 AB25 VDDDIO
C0DBGYY00578
IC8008
1
ON/OFF
2
VSS
3
NC
5
VOUT
4
VIN
IC8003C0DBEFH00002
1GND
2EN
3VTTS
4VREF5
VDDQ
6
VCC
7
VTTIN
8
VTT
C1ZBZ0003992
IC8004
1 X1
2 S0
3 S1
4 VIN
5 VDD1
6 GND1
7 CLK1
8 CLK2 9
REFOUT
10
CLK3
11
CLK4
12
GND2
13
VDD2
14
S2
15
VDD3
16
X2
C0DBFFD00005
IC8007
1VOUT
2NC
3GND
4Cn Cont
5
Sub6
VIN7
L8015J0JHC0000045
L
8
0
2
2
J
0
J
H
C
0
0
0
0
0
4
5
L8018
J0JHC0000045
L8014J0JHC0000045 L
8
0
2
0
J
0
J
H
C
0
0
0
0
0
4
5
L
8
0
1
2
J
0
J
H
C
0
0
0
0
0
4
5
L
8
0
0
3
J
0
J
H
C
0
0
0
0
0
4
5
L8017
J0JHC0000045
L
8
0
0
1
J
0
J
H
C
0
0
0
0
0
4
5
L
8
0
1
6
J
0
J
H
C
0
0
0
0
0
4
5
R8117ELJRF10NJFB
SUB1.8V
SUB3.3V_FIL
SUB3.3V
1.3V_HDMID
2.5V_ADCA
SUB3.3V
SUB1.8V
DDRVREF
DDR_VTT
SUB3.3V_FIL
SUB5V
SUB1.3V
2.5V_PLL3
SUB3.3V
2.5V_DEMO
2.5V_PLL12
3.3V_LVDSIO3.3V_HDMI
SUB2.5V
SUB3.3V
SUB2.5V SUB3.3V
1.3V_LVDSPLL
SUB3.3V
1.3V_DEMO
DDR_VTT
2.5V_PLL12
1.3V_DDRVDA
SUB1.3V
SUB3.3V
2.5V_ADCA
SUB3.3V
2.5V_PLL3
R8171
R8103R8109
R8114
R8110
R8107
R8108
R8111
R8106
R8112
TP9023
TP9032
TP9033
TP9034
TP9030
TP9040
TP9036
TP9020
TP9041
TP9043
TP9042
TP9038
TP9039
TP9044
TP9022
TP8000
TP9027
TP9024
TP9026
TP9028
TP9025
TP9035
TP9037
TP9031
TP9029
TP9021
HDMI2_DET
AD_BCLK
AG_SRQ_SYSMPU
HDMI3_DET
AG_HOST_IRQ
AG_UART_HEAD
HDMI1_DET
AD_SDO
AD_LRCLK
PANEL_STBY/VCC_ON
BCLK
TMDS_SW_S2
TMDS_SW_S1
SDIN
SPDIF
MCLK
GENX_CLK
HDMI_INT2
LRCLK
TMDS_SW_S3
XECS0
SDDAT2
XERE
RC_E-
SDCLK
EBDAT14
EBADD8
TRST
RXP0_B
SE_EEP_WP
EBADD23/NABSY_N
IFAGC
EBADD1
VINP_VSB
EBDAT0
EBADD7
EBDAT6
SDDAT1
EBADD4
SDCD
TMS
EBDAT1
HPLUG_A
RD_E+
EBADD21/NACLE
RCLK_O-
RE_O-
RE_O+
RD_O-
RD_O+
RC_O+
RC_O-
RB_O+
RB_O-
RA_O-
RA_O+
EBADD15
EBADD14
EBADD13
EBADD12
EBADD11
EBADD10
EBDAT11
EBADD9
RCLK_O+
RA_E-
RCLK_E-
RA_E+
EBDAT4
SCL_DDC_B
RXPC_B
EBDAT10
XEWE0
VRIN
EBADD2
AHDIN
AVDIN
VGIN
VBIN
AG_DTV_XRST
EBADD3
RC_E+
SYNCIN1
RB_E-
SDWP
EBDAT3
TDO
EBDAT8
EBADD18
EBADD19
EBADD20
TCK
EBADD22/NAALE
SBO2
EBDAT5
VINN_VSB
EBDAT12
EBDAT2
EBDAT13
EBADD16
EBADD17
EBDAT15
SBI2
SDDAT0
RXP2_B
RXNC_B
RD_E-
RE_E+
EBDAT9
SDCMD
RCLK_E+
RXN1_B
RB_E+
SDA_DDC_B
SE_SDA1_EEP
SE_SDA0_PANEL
SE_SCL0_PANEL
EBDAT7
RXP1_B
SE_SCL1_EEP
RE_E-
RXN0_B
LVOPDN
AMUTE
RXN2_B
HPLUG_B
SDDAT3
TDI
EBADD6
EBADD5
Q8001B1ABCF000231
Q8000B1ABCF000231
R
8
0
9
5
4
7
k
R8118
1.2k
R8113
47
R8147
10kR8125
100k
R8138
0
1MR8137
R
8
1
2
9
1
0
k
R
8
1
2
6
1
0
k
R813147
R8153
10k
R8119
2.2k
R8121
270k
R8122
1.5k
R815422
R816722
R2128 33
R2126 22
R2125 22
R8123
1.2k
R2127 100
R8135
47
R8099
2.2k
R8102
2.2k
R8098
4.7k
R8130
47
R8096 4.7k
R8097 4.7k
R8148
10kR8149
100k
R2139 68
R8120
1k
X8003
H0J270500120
X8002
H0J420500006
X8004
H0J250500094
R4743
2k
L
4
5
2
5
R4742
2k
SUB3.3V
LVDS
HDMI
DAC1
DAC2
SD CARD I/F
42MHz
FLASH
OSC
AUDIO I/F
JTAG I/F
IRQ
UART
E-BASIIC I/F
DMA I/F
2.5V
3.3V
1.3V
3.3V_HDMI
VSB
RESET
DDR2_REG
VCXO
25MHz
33.3MHz
TSCLK
C
A
2 3 6
F
1 85
E
94
B
7
D
ADC
DDR2_REG 0.9V
SUB 2.5V
3.3V_HDMI
CLOCK GEN
! A-BOARD TXN/A1HAUUS (1/15) Seine3LV
TO 3/15
TO 5/15
TO 3/15
TO 5/15
TO 3/15
TO 8/15
TO 7/15
TO 5/15
TO 3/15
TO 3/15
TO 3/15
TO 7/15
TO 7/15
TO7,10/15
TO8/15
TO 8/15
TO 3,7/15
TO 8/15
TO 5/15
TO 8/15
TO 9/15
TO 11/15
TO 7,12/15
TO 12/15
TO 7/15
C1AB00003078
Seine3LV
IC8001
-
48
12.6. A-Board (2/15) Schematic Diagram
+
CH0A10
CH0DQS1
CH0DM0
CH0A5
CH0A0
CH0ODT
CH0A3
CH0A11
CH0BA1
CH0A8
CH0BA0
CH0A6
CH0XCS0
CH0XCAS
CH0A2
CH0XRAS
CH0XCK
CH0A4CH0BA2
CH0DM1
CH0CKE
CH0DQS0
CH0A1
CH0XWE
CH0A9
CH0A12
CH0A7
CH0CK
CH0A0
CH0A1
CH0A2
CH0A3
CH0A4
CH0A5
CH0A6
CH0A7
CH0A8
CH0A9
CH0A10
CH0A11
CH0A12
CH0BA0
CH0BA1
CH0BA2
CH0XWE
CH0XRAS
CH0XCAS
CH0XCS0
0.9V
CH0DM0
CH0DM1
CH0DQS0
CH0DQS1
CH0DQ0
CH0DQ2
CH0DQ4
CH0DQ6
CH0DQ8
CH0DQ10
CH0DQ12
CH0DQ14
CH0DQ1
CH0DQ5
CH0DQ3
CH0DQ13
CH0DQ9
CH0DQ15
CH0DQ7
CH0DQ11
CH0CKE
CH0ODT
CH0DQ15
CH0DQ13
CH0DQ7
CH0DQ8
CH0DQ0
CH0DQ9
CH0DQ4
CH0DQ12
CH0DQ6
CH0DQ14
CH0DQ2
CH0DQ1
CH0DQ11
CH0DQ5
CH0DQ10
CH0DQ3
CH0CK
CH0XCK
C8040
50V1000p
C8048
16V
0.1u
C8043
16V
0.1u
C8036
10u10V
C8047
16V
0.1u
C8046
16V
0.1u
C8138
50V1000p
C8149
50V5p
C8186
2200p50V
C8185
16V
0.1u
C8184
4.7u
10V
C8189
16V
0.1u
C8042
68u4V
IC8001
C1AB00003078
A1 VSS
IC8002
C3ABSY000036
A1 VDD
IC8001 E5 VSS
IC8001U25DDRBA0
IC8001 N12 VSS
IC8001 N13 VSS
IC8001 N14 VSS
IC8001P26DDRAD3
IC8001V24DDRCS0_N
IC8001R24DDRAD6
IC8001N22DDRAD12
IC8001J22DDRD0_VREF
IC8001N24DDRAD7
IC8002 J9 VDD
IC8002 L2 BA0
IC8002 F7 LDQS
IC8002 H8 VSSQ
IC8002 P9 VSS
IC8002 P8 A8
IC8002 C1 VDDQ
IC8002 R2 A12
IC8002 B8 VSSQ
IC8002 N7 A6
IC8002 R7 NC
IC8002 H2 VSSQ
IC8002 K2 CKE
IC8002 L3 BA1
IC8002 F3 LDM
IC8002 C9 VDDQ
IC8001 L16 VSS
IC8002 N8 A4
IC8002 K7 RAS
IC8002 J7 VSSDL
IC8001AA26DDRCLK
IC8002 R8 NC
IC8002 P7 A11
IC8002 N1 VSS
IC8002 A9 VDDQ
IC8002 M8 A0
IC8002 D8 VSSQ
IC8002 E8 LDQS
IC8002 A2 NC
IC8002 M3 A1
IC8002 J1 VDDL
IC8002 N2 A3
IC8002 F2 VSSQ
IC8002 E9 VDDQ
IC8002 M2 A10
IC8002 G9 VDDQ
IC8002 G1 VDDQ
IC8002 A7 VSSQ
IC8002 L7 CAS
IC8002 D2 VSSQ
IC8001T25DDRAD2
IC8002 E1 VDD
IC8002 A3 VSS
IC8002 R1 VDD
IC8002 P3 A9
IC8002 C7 VDDQ
IC8002 K3 WE
IC8002 C3 VDDQ
IC8002 K9 ODT
IC8002 R3 NC
IC8001H26DDRDQS0
IC8002 N3 A5
IC8002 G7 VDDQ
IC8002 B7 UDQS
IC8002 B2 VSSQ
IC8002 A8 UDQS
IC8002 F8 VSSQ
IC8002 J2 VREF
IC8002 E2 NC
IC8002 P2 A7
IC8002 E3 VSS
IC8001AA23DDRCAS_N
IC8002 E7 VSSQ
IC8001 N11 VSS
IC8002 L8 CS
IC8001 M11 VSS
IC8001 L13 VSS
IC8001U23DDRBA1
IC8001 AA25 DDRVSSCLK1
IC8001 R4 AVSSR
IC8001 R1 AVSSP12
IC8001 P4 AGND1
IC8001 T5 AVSSP12
IC8001 Y25 DDRVSSCLK2
IC8001 V3 AVSSHDMI
IC8001 AB3 AVSSHDMI
IC8001 W5 AVSSHDMI
IC8001 W4 AVSSHDMI
IC8001 W3 AVSSHDMI