osu craft center woodworking studio manual

11
OSU CRAFT CENTER WOODWORKING STUDIO MANUAL Contents I. General A. Woodshop Use B. Procedures C. Safety D. Emergency II. Facilities Woodshop III. Stationary Tool Safety a.) Big Band Saw b.) Edge Sander c.) Combination Sander d.) Spindle Sander e.) Compound Miter Saw F.) Drill Press g.) Jointer h.) Planer i. Table SawSawstop i.i.) Table saw Delta for Dado k.) Router l.) Wood Lathes IV. Hand Tool Safety a. Belt Sander b. Detail Sander c. Drill d. Finishing Sander e. Jig Saw g. Random Orbital Sander Warning: The Woodworking studio has tools and equipment that may cause personal bodily injury, especially if improperly used. Knowledge and understanding of policies, practices and safe operation procedures are each member’s responsibility. The Craft Center reserves all rights to change and/or modify policies or procedures and access at any time as they relate to safety, misuse or related situations. All policies are strictly enforced. General A. Woodshop Use The woodshop is available for fine woodworking projects. It is meant for the hobbyist and not for production enterprises. Craft Center Membership Required. Woodshop Access Privileges may be extended after: Successful completion of a Craft Center basic woodworking class along with manual reading, passing safety test and attending an Orientation either in class or separately.

Upload: others

Post on 22-May-2022

4 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

OSU CRAFT CENTER WOODWORKING STUDIO MANUAL Contents  

 I.  General  

 A.  Woodshop  Use    

 B.  Procedures  

 C.  Safety      

 D.  Emergency  

 II.  Facilities  

Woodshop    

III.  Stationary  Tool  Safety  

 a.)  Big  Band  Saw    

 b.)  Edge  Sander    

c.)  Combination  Sander  

d.)  Spindle  Sander    

e.)  Compound  Miter  Saw    

F.)  Drill  Press  

g.)  Jointer    

h.)  Planer  

i.  Table  Saw-­‐Sawstop  

i.i.)  Table  saw-­‐  Delta  for  Dado  

 k.)  Router      

l.)  Wood  Lathes  

IV.  Hand  Tool  Safety    

a.  Belt  Sander  

b.  Detail  Sander    

c.  Drill  

d.  Finishing  Sander  

e.  Jig  Saw  

g.  Random  Orbital  Sander  

 

 

Warning:  The  Woodworking  studio  has  tools  and  equipment  that  may  cause  personal  bodily  injury,  especially  if  improperly  used.  

 Knowledge  and  understanding  of  policies,  practices  and  safe  operation  procedures  are  each  member’s  responsibility.    The  Craft  Center  reserves  all  rights  to  change  and/or  modify  policies  or  procedures  and  access  at  any  time  as  they  relate  to  safety,  misuse  or  related  situations.    All  policies  are  strictly  enforced.  

 

General    

A.    Woodshop  Use  The  woodshop  is  available  for  fine  woodworking  projects.  It  is  meant  for  the  hobbyist  and  not  for  production  enterprises.  Craft  Center  Membership  Required.    

Woodshop  Access  Privileges  may  be  extended  after:    

Successful  completion  of  a  Craft  Center  basic  woodworking  class  along  with  manual  reading,  passing  safety  test  and  attending  an  Orientation  either  in  class  or  separately.  

Page 2: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  2    

Experienced  woodworker  must  watch  safety  video,  read  safety  manual,  pass  safety  test  &  attend  Studio  Orientation.    The  safety  test  will  be  good  for  1  academic  year.  Studio  orientations  are  required  every  term.  

Equipment  Access¬  Safety  clearance  allows  access  to  any  machine  or  tool  you  are  knowledgeable  in.  If  you  do  not  know  the  correct  way  to  use  a  tool  or  machine  do  not  use  it,  ask  for  help,  and/or  take  a  beginning  wood  class  to  learn.  Misuse  or  abuse  of  a  tool  will  suspend  its  availability.  Only  use  equipment  as  it  was  intended  for  use  by  the  manufacturer.  

B.    Procedures    Safety  Requirements  -­‐  Each  person  must:  

• Watch  the  Woodshop  Safety  Video-­‐  (Available  at  Craft  Center  front  desk  or  on-­‐line)      • Read  &  Comprehend  the  Safety  Manual-­‐  (Available  at  Craft  Center  front  desk  or  on-­‐line)      • Complete  &  Pass  the    Safety  Quiz  -­‐(Available  at  Craft  Center  front  desk  or  on-­‐line)      • Sign  the  User  Safety  Agreement-­‐  (Available  at  Craft  Center  front  desk  only)      

Numbers  1-­‐3  above  will  be  available  at  the  Craft  Center  or  on-­‐line  at  http://mu.oregonstate.edu/craft-­‐center/current-­‐class-­‐schedule/wood-­‐working  

The  SAFETY  QUIZ  must  be  submitted  to  the  Front  Desk  in  order  for  the  quiz  to  be  graded  The  User  Agreement  must  be  signed  by  each  member.  

Once  the  above  is  satisfactorily  completed,  a  member’s  craft  center  membership  card  will  be  stamped  for  use  to  check  out  tools  and  keys  to  access  equipment.  This  transaction  occurs  at  the  craft  center  front  desk.  

A  current  craft  center  membership  is  required  &  member  must  submit  their  membership  card  with  valid  wood  stamp  at  the  time  of  tool  check  out.  

Check  out    

• Any  tool  you  have  checked  out  must  be  returned  to  the  Front  Desk  personnel    

Clean  up    

• Your  work  area  must  be  clean  before  you  leave.    • Most  machines  are  directly  connected  to  a  dust  collection  system.  Make  sure  to  open  the  blast  gate  before  

operation  &  close  when  through;  there  is  a  pole  with  hook  in  the  studio  that  can  be  used  to  reach  the  blast  gate.  • Member  is  responsible  to  sweep  up/  clean  any  wood  debris  not  removed  by  the  dust  collection  system  on  or  

around  the  machine  /work  area.    • Brooms,  dust  brush  &  pans  are  located  in  the  studio.  Dispose  of  wood  chips  &  debris  into  proper  labeled  bin.  

Please  minimize  amount  of  debris  that  goes  into  floor  port,  reserving  that  for  final,  fine  wood  particles.  • Place  newspaper  or  old  catalogs  beneath  items  to  be  glued.  Wipe  up  any  glue  spills.  • Failure  to  properly  clean  your  workspace  may  void  woodshop  privileges.      

Storage  

• Due  to  minimal  storage  space  in  the  woodshop,  projects  should  be  stored  short  term  ONLY.    • Wood  stock  should  be  labeled,  dated  &  properly  stored  in  a  reserved  wood  bin.  • Wood  bins  expire  at  end  of  term  &  items  should  be  removed  or  bin  renewed  along  with  membership.  

 

Page 3: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  3    

C.  Safety    Accidents-­‐  Report  everything!    We  need  to  know  for  your  safety.    Inform  Craft  Center  Staff  as  soon  as  possible.    Minor  incidents  are  important.      Accidents  include  any  personal  harm  or  any  damage  done  to  machines  or  tools.  Danger=  Anything  that  appears  to  be  an  immediate  or  potential  hazard  should  be  dealt  with  immediately.    

• Damaged  equipment  should  be  reported.      • Electrical  Hazards  -­‐  Keep  out  of  any  electrical  control  boxes.      • Moving  Parts  -­‐  Always  keep  your  hands  and  other  extremities  away  from  all  moving  parts.  

   Eye  Protection    

• Imperative  when  working  with  or  around  any  tools  and  machinery,  even  if  you  are  not  using  the  equipment.    

 Eye  protection  must  be  worn  at  ALL  times  when  you  are  in  the  shop.    This  is  the  law;  there  are  no  exceptions!      

   Face  Shields  ¬  Required  when  using  lathe,  but  advised  for  all  machinery.  

 Ear  Protection  -­‐  Available  and  strongly  advised.  

 Dust  Masks  –  Disposable  masks  are  available  for  purchase  from  craft  center  supply  store  or  you  can  provide  your  own.  Whenever  working  with  wood,  dust  is  produced  and  can  be  a  hazard.    Certain  woods  could  contain  harmful  chemicals  and  Western  Red  Cedar  has  been  attributed  to  asthma  and  nasal  cancer.  It  is  advisable  to  wear  a  particulate  mask  when  creating  high  levels  of  saw  dust  and  always  keep  work  area  clean.    OSHA  has  information  &  resources  on-­‐line  with  regard  to  general  respiratory  protection  guidance;  members  are  encouraged  to  be  informed  and  to  decide  what  protection  is  best  for  them.  

No  Food,  Drinks,  tobacco,  alcohol,  or  drugs,  legal  or  otherwise.¬  Do  not  operate  machinery  under  the  influence  of  any  drug  or  alcohol,  of  if  fatigued.  

Clothing  

 1.  Long  hair  must  be  pulled  back  and  secured.  

 2.  No  loose  clothing.    Long  sleeves  should  be  rolled  up  and  shirt  tails  should  be  tucked  in.    

 3.  Must  be  wearing  full-­‐length  pants.    

4.  Shoes  must  be  rubber  soled  and  closed  toed,  No  sandals,  etc.  

5.  No  jewelry  can  be  worn,  including  watches  and  dangling  earrings.    

6.  Backpacks  and  other  belongings  must  be  hung  on  coat  hooks  or  stowed  away  from  work  area.  

7.  Do  not  wear  gloves  when  using  power  equipment.  

 8.  Electronics-­‐  No  headphones  or  cellular  devices  while  operating  equipment.    

 

 

 

Page 4: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  4    

D.  Emergency      Shut  off  equipment  immediately  upon  an  emergency.      

A  fire  extinguisher  is  located  in  the  shop  to  the  left  of  the  sink.  It  is  for  small  localized  fires.  Personal  safety  is  paramount,  if  fire  danger  is  great-­‐  exit  building  &  call  911.    

A  First  Aid  box  is  located  near  the  sink  and  other  locations  throughout  the  craft  center.      

Have  craft  center  staff  assist  you  with  all  injuries.    Complete  accident  report  with  front  desk  staff  when  able.  

Emergency  Assistance  -­‐  Dial  9911  from  on-­‐  campus  phones.      

 

Facilities  1.  Woodshop  houses  all  the  stationary  tools  that  are  connected  to  a  sawdust  vacuum  collection  system.    A  Studio  Orientation  will  familiarize  you  with  procedures,  how  it  operates  and  your  responsibilities  as  they  relate  to  it.  

2.  Two  worktables  are  equipped  with  electrical  outlets  for  hand  tools  and  vises  to  secure  projects.    

3.  Chemical  use  is  not  allowed  in  this  room,  this  is  a  fire  hazard.  No  Solvent  based  products,  epoxies,  etc..  

4.  Membership  card  required  for  key  check-­‐out  for  machine  operation  and  tools  sign-­‐out.  

Respect  your  peers  and  staff  -­‐  Be  considerate  and  helpful  toward  each  other.  

 

Stationary  Tool  Safety    1.  Use  machines  only  as  intended.    If  in  doubt,  ask  for  assistance  and/or  refer  to  USER  MANUAL.      

2.  You  should  be  experienced  and  informed  in  operation  and  safety  procedure.  If  you  are  not  comfortable          with  a  machine,  do  not  use  it;  ask  for  assistance.    

3.  Focus  on  your  work.    Look,  listen,  and  be  in  control  of  what  you  are  doing.    Do  not  be  distracted  by  or  talk  to  others  while  operating  machinery  and  do  not  distract  others.      

4.  Avoid  accidental  starting.  Only  the  person  using  the  machine  should  ever  start  it!  

5.  All  Safety  guards  and  devices  must  be  in  place  when  operating  machines.  

6.  Do  not  overreach.    

7.  Machine  must  be  at  rest  before  removing  byproducts  and  turned  “off”  before  leaving.  

8.  Return  adjustable  parts  to  rest  position.  Machine  should  be  clean  and  clear  before,  during,  and  after  it  is                            used.      

9.  Red  knobs  are  not  for  adjustments.    These  are  for  calibrations  that  should  ONLY  be  done  by  trained  staff.  

10.  Make  all  adjustments  with  the  power  box  switched  off!    .    

11.  All  adjustable  parts  should  be  secure  before  power  is  on.    

Page 5: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  5    

12.  DO  not  use  force.    The  tool  should  do  the  work.    If  it  does  not  perform  as  you  expect,  let  Staff  know;      

There  may            be  a  better  way.    

13.  Stay  within  reach  of  power  switch  at  all  times.  

14.  Check  for  worn  and  damaged  parts.    Let  TRAINED  STAFF  correct  these  problems.  Do  not  attempt  it  yourself.    

15.  Machinery  should  not  be  used  to  cut  bucked  limbs  or  stumps,  used  wood,  wet  wood,  plaster  or  drywall.    Studio  is  for  milled,  dry  wood,  and  furniture-­‐grade  wood.  

Band  Saw  -­‐  Free-­‐hand  tool  designed  for  cutting  circles  and  curves.      Can  also  be  used  to  rip  and  crosscut  relatively  small  pieces  of  wood.  Safety  -­‐  eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Always  keep  hands  and  fingers  3”  away  from  the  cutting  edge.  

2.  Upper  guide  should  be  only  1/8”  above  material  height.    

3.  Hold  wood  firmly  feeding  it  into  blade  at  a  moderate  speed.    

4.  Check  band  for  good  tension.  

 5.  Avoid  backing  wood  out  of  an  incomplete  cut.  

 7.  Blade  inhibits  tight  turns  that  could  twist  and  break  band;  make  multiple  relief  cuts  to  decrease  stress.    

8.  Clicking  while  blade  is  in  motion  indicates  a  hazard.  If                                                                                                                                                                                                                  you  hear  this,  STOP,  Inform  STAFF.  

9.  Bandsaw  brake  must  always  be  applied  after  shutting  off  switch.  

 

Edge  Sander  -­‐  Free-­‐hand  tool  for  sanding  small  pieces  of  wood.  

Safety  -­‐  Eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Sand  only  in  the  direction  of  the  wood  grain    

2.  Do  not  apply  excessive  force.    

3.  Check  sanding  surfaces  for  tears  or  holes.    Worn  surfaces  should  be  replaced.    

4.  Check  belt  traction  while  running  

5.  Gloves  should  not  be  worn,  neither  should  you  hold  object  with  rag.      

Page 6: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  6    

   

Combi-­‐Disc/Belt  Sander  -­‐  Free-­‐hand  and  tool  for  sanding  small  pieces  of  wood.  

Safety  -­‐  Eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Sand  only  in  the  direction  of  the  wood  grain  on  the  downward  stroke  of  the    

         machine.  

2.  Do  not  apply  excessive  force.    

3.  Check  sanding  surfaces  for  tears  or  holes.    Worn  surfaces  should  be  replaced.    

4.  Check  belt  traction  while  running.    

 

Spindle  Sander  -­‐  Used  for  sanding  curved  surfaces.    

Safety  -­‐  Eye  protection  is  required  by  law.  Do  not  be   distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Sanding  spindle  should  be  appropriate  size  for  the   radius  of  the  curve  you  need  to  sand.  

2.  Keep  wood  flat  on  table  while  sanding.  

3.  Do  not  apply  excessive  force.  

4.  Check  sanding  surfaces  for  tears  or  holes.    Worn  surfaces  should  be  replaced.    

 

12”  Compound  Slide  Miter  Saw  -­‐  Used  for  cross  cuts,  miter  and  compound  miter  jointing.      

Safety  -­‐  Eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Blade  should  be  sharp,  run  freely,  and  be  free  of  vibration.    

2.  Let  blade  come  to  full  speed  before  beginning  cut.    

3.  Hold  material  with  hand  away  from  blade  and  keep  your  fingers  and  thumb  together.  

4.  Do  not  cross  your  arms  while  using  the  saw.      

5.  Start  the  saw,  pull  out,  push  down,  and  push  back.  

6.  Allow  blade  to  stop  completely  before  lifting  up.  

7.  Do  not  attempt  to  cut  small  pieces.  

Page 7: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  7    

8.  Do  not  handle  blade  guard.    It  is  designed  to  self-­‐retract.      

   

15”  Variable  Speed  Drill  Press  -­‐  Designed  to  make  vertical  holes  or  create  mortises.      

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.          

1.  Larger  bits  should  be  used  at  slower  speeds.      

2.  Place  scrap  stock  underneath  material  to  be  cut  in  order  to  protect  base.      

3.  Clamp  scrap  stock  to  base.  

 

8”  Long  Bed  Jointer  -­‐  For  squaring  and  shaving  along  the  edge  grai

n.      

Safety  -­‐  Eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Use  a  push  block  whenever  project  goes  over  the  cutting  surface  keeping  fingers  4”  from  the  cutting  knives.  

2.  Wood  should  be  more  than  6”  long.    

3.  Never  adjust  out-­‐feed  table.  

4.  Feed  against  blade  rotation.  Reverse  direction  can  cause  serious  injury.  

 

Planer  -­‐  Designed  to  plane  stock  to  any  thickness  smoothly.  This  machine  cannot  straighten  bows  or  warps.  

Safety  -­‐  eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Use  only  if  trained  specifically  on  this  machine.  

 2.  Plane  off  only  1/16”  each  pass.      

3.  Keep  others  out  of  line  of  in-­‐feed  and  out-­‐feed  of  table.  

4.  Plane  only  clean  clear  wood.  Any  imperfections  in  the  wood  should  be  checked  first.  

 

5.  Only  one  piece  of  wood  at  a  time.  Do  not  start  a  second  until  first  is  clear  and  do  not  stack.  

6.  If  board  stops  moving,  turn  power  off  immediately,  lower  deck,  and  get  trained  personnel.  

Page 8: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  8    

7.  Clear  dust  and  woodchips  with  brush  not  hand.  

8.  Feed  against  blade  rotation.  Reverse  direction  can  cause  serious  injury.  

 

Table  Saw  -­‐  SAWSTOP  Ripping  and  Crosscutting  stock.  

Safety  -­‐  eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

1.  Use  a  push  block  whenever  project  goes  over  the  cutting  surface.  Keep  hands  at  least  4”  from  blade.  

2.  Stand  to  side  of  wood  being  ripped.    

3.  Stay  within  reach  of  power  switch.  

4.  Only  use  one  fence  or  miter  gauge.  

5.  Be  sure  adjustment  wrenches  or  any  other  objects  have  been  removed  from  table  before  use.  

6.  Hold  wood  firmly  feeding  it  into  blade  at  a  moderate  speed.    Push  wood  with  a  push  stick  until  it  clears  cutting  blade.      

7.  This  in  not  a  free-­‐hand  machine.    Always  use  a  fence  or  miter  gauge.  

8.  Feed  against  rotation.    Wrong  way  will  accelerate  wood  and  cause  damage.      

9.  No  dead-­‐cuts.    Continue  ripping  all  the  way  through  your  board  without  stopping.      

10.  Only  use  wood  that  has  flat  surfaces  and  is  dry,  No  wet  wood.      

11.  Only  one  piece  of  wood  at  a  time.    Do  not  start  a  second  until  first  is  clear.      

 

Table  Saw  -­‐  DELTA  used  for  Dado  cuts  

Safety  -­‐  eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.  

Delta  saw  does  NOT  have  a  safety  brake  system.  

 

Follow  steps  1-­‐11  above.  

When  changing  out  blades-­‐  tightly  secure,  but  do  not  over  tighten.  

 

Page 9: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  9    

Routers  -­‐  Used  for  milling  and  shaping  wood  edges  and  free  forms.    

Safety  -­‐  eye  protection  is  required  by  law.  Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.  

1.  Hold  with  both  hands.    This  tool  is  easy  to  lose  control  of.    

2.  Bits  can  be  extremely  hot  after  use.      

3.  Keep  base  on  flat  surface  for  smooth  cuts.      

4.  Make  progressive  cuts  to  desired  depth.      

5.  Speed  should  be  reduced  for  larger  bits.      

6.  Do  not  “Climb-­‐cut.”    Cut  outside  edges  counter-­‐clockwise  and  inside  edges  clockwise.    

 

Wood  Lathe  -­‐  Milling  original,  symmetrical  wood  profiles.    

Requires  separate  class/  training,  and  is  for  very  experienced  woodworkers  only.  

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  machinery.          

 

Hand  Tool  Safety  1.  Use  tools  only  as  intended.    If  in  doubt,  ask  for  assistance  and/or  refer  to  a  user  manual.        

2.  You  should  be  informed  in  operation  and  safety  procedure.  If  you  are  not  comfortable  with  a  machine,  do  not  use  it;  ask  for  assistance.  

3.  Focus  on  your  work.  Look,  listen,  and  be  in  control  of  what  you  are  doing.  Do  not  be  distracted  by  or  talk  to  others  and  do  not  distract  others.  

4.  All  safety  guards  and  devices  must  be  in  place  when  operating  tools.  

5.  Avoid  accidental  starting.  

6.  Tool  should  be  at  rest  before  removing  byproduct  and  laying  it  down.  Unplug  a  tool  that  is  not  being  used.      

7.  Unplug  tool  before  changing  parts  and  making  adjustments.  Be  sure  bits  and  blades  are  secure  before  usage.  Turn  switch  to  “OFF”  before  plugging  into  socket.      

8.  Return  adjustable  parts  to  rest  position.  Machine  should  be  clean  and  clear  before,  during,  and  after  it  is  used.  

9.  Do  not  use  force.  The  tool  should  do  the  work.  If  it  does  not  perform  as  you  expect,  let  trained  personnel  know.  There  may  be  a  better  way.  

10.  Do  not  overreach.  

11.  Extension  cords  must  be  3-­‐prong  grounded  or  polarized.  If  a  2-­‐prong  cord  will  not  fit,  flip  it  over.  

Page 10: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  10    

12.  Pull  plug  out  from  sockets  by  the  grip  not  the  cord.      

13.  Use  clamps  and  vises  to  hold  down  wood  or  metal.  Keep  your  hands  free  to  control  the  hand  tool.  

14.  Cords  can  be  electrocution  hazards.  Be  sure  they  run  behind  you,  out  of  the  tools  direction.  

15.  Hold  by  insulated  gripping  for  greater  shock  protection.      

16.Check  for  worn  and  damaged  parts.    Let  trained  personnel  correct  these  problems.    Do  not  attempt  it    yourself.      

17.  Wood  should  be  flat  and  clear  of  all  foreign  objects.    

 

Belt  Sander  -­‐  This  tool  is  designed  to  smooth  larger  items  like  rough  boards.      

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.          

1.  Hold  with  both  hands.    This  tool  is  easy  to  lose  control  of.      

2.  Belt  must  be  tracked  properly  before  use.  

3.  The  weight  of  the  sander  is  sufficient.    Leaning  on  the  tool  is  bad  for  the  motor  and  is  less  effective.  

 

 Finishing  Sander  -­‐  Half  and  quarter  sheet  sanders  for  finishing  flat  surfaces.      

Safety-­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.          

1.  The  weight  of  the  sander  is  sufficient.  Excess  pressure  on  the  tool  is  bad  for  the  motor  and  is  less  effective.  Abrasive  paper  should  be  secure  before  use.      

 

Random  Orbital  Sander  -­‐  This  palm-­‐sized  sander  removes  material  more  rapidly  than  a  finish  sander.  

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.          

1.  A  moderate  grip  on  the  sander  is  sufficient.  Excessive  force  is  bad  for  the  motor  and  is  less  efficient.  

2.  Abrasive  paper  should  be  secure  before  use.      

3.  This  tool  is  capable  of  abrasions  unlike  finishing  sanders.      

 

Drill  -­‐  This  tool  is  designed  to  drill  various  sized  straight  holes  into  wood  or  metal.      

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.          

1.  Drill  straight  in  and  pull  straight  out.  Twisting  or  wobbling  bit  in  a  hole  will  damage  the  bit  and  cause  bodily  harm.  

2.  Bits  can  be  extremely  hot  after  use.      

3.  Be  sure  to  drill  with  motor  in  forward  direction.    Reverse  direction  will  burn  or  can  ignite  wood.      

Page 11: OSU CRAFT CENTER WOODWORKING STUDIO MANUAL

Page  |  11    

4.  Pull  bit  out  of  deep  holes  to  remove  debris.    Excess  chips  can  cause  overheating.      

 

Jig  Saw  -­‐  This  tool  is  generally  used  for  pattern  cutting  into  materials  with  the  maximum  thickness  of  4  1/4”  for  wood.    

Safety  -­‐  Eye  protection  is  required  by  law.    Do  not  be  distracted  by  or  talk  to  others  when  operating  tools.          

1.  Find  a  clear  area  to  work  with  this  tool  and  secure  the  material.      

2.  Keep  base  on  flat  surface  when  in  use.      

3.  Do  not  use  a  bent  blade.    

 

Clamps  

• There  are  several  styles  &  sizes  of  clamps  located  in  the  studio.  • If  gluing,  use  newspaper  under  work.  Clean  up  any  glue  spills  before  they  set.  • Limit  the  time  work  is  clamped  and  occupying  a  table  space;  return  day  after  gluing  to  unclamp,  properly  stow  

work  and  put  clamps  back  where  they  belong.      • Label  clamped  work  with  full  name  and  date.  

 

Golden  Rules  of  the  Woodshop  SAFETY    MUST    ALWAYS    BE    FIRST.    

Don’t  operate  a  machine  or  tool  if  you  are  not  trained  and  familiar  with  it!  

If  you’re  tired….  take  a  break  

If  you  open  it  .  .  .  Close  it  

If  you  turn  it  on  .  .  .  Turn  it  off  

If  you  unlock  it  .  .  .  Lock  it  

If  you  checked  it  out  .  .  .  You  must  check  it  back  in  

If  you  use  it  .  .  .  Take  care  of  it  

If  you  break  it  .  .  .  Report  it  

If  you  glued  it  .  .  .  Tag  it  with  date  and  time  

If  you  make  a  mess  .  .  .  Clean  it  up  

If  it  is  in  the  way  .  .  .  Move  it      If  you  moved  it  .  .  .  Put  it  back  

If  you  are  confused  .  .  .  Ask  for  help  

If  you  are  unable  to  operate  it  .  .  .  Leave  it  alone!