Nemo Handy 2.50 Display Guide N80

Download Nemo Handy 2.50 Display Guide N80

Post on 12-Nov-2015

217 views

Category:

Documents

1 download

DESCRIPTION

Nemo Handy 2.50 Display Guide N80

TRANSCRIPT

  • Nemo Handy Display Guide

    For Nemo Handy 2.50

    Nokia N80

  • 2008 by Anite Finland Ltd. All rights reserved.

    This manual, as well as the software described in it, is furnished under license and may only be used or copied in accordance with the terms of such license. The information in this manual is intended for informational use only and is subject to change without notice. Anite Finland Ltd assumes no responsibility or liability for any errors or inaccuracies that may appear in this user manual.

    Except as permitted by such license, no part of this publication may be reproduced or transmitted in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Anite Finland Ltd.

    Windows, Windows 2000 and Windows XP, Outlook, and Internet Explorer are registered trademarks of the Microsoft Corporation in the United States and other countries. MapInfo and MapX are registered trademarks of MapInfo Corporation. CDMA 2000 is a registered trademark of the Telecommunications Industry Association (TIA -USA). The license management portion of this Licensed Technology is based on SentinelLM* 1989-2003 Rainbow Technologies, Inc. All rights reserved.

    Revision 2.50.00, Last edited April 2008

  • CONTENTS

    NEMO HANDY VIEWS........................................................................................4 STATUS VIEW ......................................................................................................5 SCRIPT VIEW .......................................................................................................6 INDOOR MAP .......................................................................................................7 GPS VIEW..............................................................................................................8 BROWSER VIEW .................................................................................................9 TESTING VIEW..................................................................................................10

    TIMESLOT TESTING .............................................................................................10 CELL TESTING.....................................................................................................11

    GSM VIEWS ........................................................................................................12 VIEW 1/9 FOR GSM.............................................................................................12 VIEW 2/9 FOR GSM.............................................................................................17 VIEW 3/9 FOR GSM.............................................................................................18 VIEW 4/9 FOR GSM.............................................................................................19 VIEW 5/9 FOR GSM.............................................................................................20 VIEW 6/9 FOR GSM.............................................................................................21 VIEW 7/9 FOR GSM.............................................................................................22 VIEW 8/9 FOR GSM.............................................................................................24 VIEW 9/9 FOR GSM AND UMTS .........................................................................27 WLAN VIEW.......................................................................................................28

    UMTS VIEWS......................................................................................................31 VIEW 1/9 FOR UMTS ..........................................................................................31 VIEW 2/9 FOR UMTS ..........................................................................................34 VIEW 3/9 FOR UMTS ..........................................................................................35 VIEW 4/9 FOR UMTS ..........................................................................................36 VIEW 5/9 FOR UMTS ..........................................................................................37 VIEW 6/9 FOR UMTS ..........................................................................................38 VIEW 7/9 FOR UMTS ..........................................................................................40 VIEW 8/9 FOR UMTS ..........................................................................................41

  • 4 Nemo Handy Display Guide

    NEMO HANDY VIEWS

    Below are presented the various measurement views available in Nemo Handy. You can browse the various views with the left and right arrow buttons. With the up and down arrow buttons you can scroll the views. By pressing the navigation button, you can switch between different parameters within a view. Note that the scales in the bar and line graphs will change according to the selected parameter.

    Nemo Configuration Editor enables you to create your own Nemo Handy views. The views described here are the default views.

  • 5 Nemo Handy Display Guide

    STATUS VIEW

    Logging State tells the current recording status.

    Log File Size displays the size in bytes of the measurement file.

    Free Space displays the available memory card memory space.

    Free Memory displays the current amount of free RAM.

    System Lock, Channel Lock, Scr. Lock, and Cell Barring display status info for the different forcing functions.

    GPS Status displays the status of the GPS receiver.

    Log File Path displays the location where the measurement files are stored on the memory card.

    Log File Name displays the measurement file name.

  • 6 Nemo Handy Display Guide

    SCRIPT VIEW

    Status tells the current status of the script.

    APN displays the access point name.

    File displays the name of the script file.

    Repeats displays how many times the script is repeated and the ordinal number of the current repeat.

    Command displays the number of commands in the current script and a description of the command, e.g., VoiceCallStart.

    State describes the current mobile state.

  • 7 Nemo Handy Display Guide

    INDOOR MAP

    You can view indoor maps in Nemo Handy and plot the measurement route on the map with markers.

    You can move and zoom on the map with the following buttons:

    2 = Up

    4 = Left 5 = Marker 6 = Right

    7 = Zoom out 8 = Down 9 = Zoom in

    To draw the route on the map, place markers along the route. Press button 5 twice to place a marker. If the Draw route setting is on in the Indoor Map Settings, the markers will be connected to form a route.

  • 8 Nemo Handy Display Guide

    GPS VIEW

    The GPS view is available only if a GPS is connected to Nemo Handy and the license supports the GPS.

    Latitude/Longitude displays the latitude/longitude coordinates.

    Height displays the current height in meters.

    Distance displays the distance traveled from the starting point.

    GPS Status displays the current status of the GPS, i.e., if there is a fix.

    Satellites displays the number of satellites currently visible.

    Velocity displays the current velocity of the test unit in kilometers per hour.

  • 9 Nemo Handy Display Guide

    BROWSER VIEW

    The Browser view displays the HTML content when you run a HTML browsing script.

  • 10 Nemo Handy Display Guide

    TESTING VIEW

    TIMESLOT TESTING

    Status displays the status of the testing procedure.

    Repeat displays the number of calls that have been made during the testing session.

    Phone number displays the test number to which the calls are made during the testing session.

    Channel displays the channel number of the tested channel.

  • 11 Nemo Handy Display Guide

    CELL TESTING

    Channel displays the channel number of the tested cell.

    Voice displays whether the tested cell connects voice calls successfully.

    PDP displays whether the tested cell connects PDP connections successfully.

  • 12 Nemo Handy Display Guide

    GSM VIEWS

    VIEW 1/9 FOR GSM

    System displays the current cellular system, e.g., GSM 1800.

    Packet Tech. displays the packet data technology used. Alternatives are GPRS, EGPRS, and UMTS.

    Channel displays the current channel number.

    CI displays the 16-bit cell identification code.

    BCCH displays the broadcast control channel number.

    BSIC displays the base station identity code.

    Channel Type displays the current channel type. Alternatives are FR, HR, EFR, AFR, and AHR.

    RX Level displays the RX level full value when the mobile is in idle mode and the RX level sub value when a call is connected. Values range from -120 to -10 dBm.

    RX Quality displays the RX quality full value when the mobile is in idle mode and the RX quality sub value when a call is connected. Values range from 0 to 7.

    C1 & C2 display the C1 and C2 values.

  • 13 Nemo Handy Display Guide

    N1 Channel displays the channel number for the first neighbor.

    N1 RX Level displays the RX level for the first neighbor.

    LAC displays the location area code.

    MCC displays the mobile country code.

    MNC displays the mobile network code.

    TA displays the timing advance value. Values range from 0 to 63.

    MSP displays the mobile station Tx power. Values range from 0 to 32.

    MSP (dBm) displays the mobile station Tx power in dBm.

    MAIO displays the mobile allocation index offset.

    HSN displays the hopping sequence number.

    RLT displays the radio link timeout.

    Voice TS DL/UL displays the numbers of used timeslots during voice call in uplink (UL) and downlink (DL) directions.

    Packet TS DL/UL displays the numbers of used timeslots during packet data connection in uplink (UL) and downlink (DL) directions.

  • 14 Nemo Handy Display Guide

    Emergency call displays whether emergency calls are supported in the cell (Y/N).

    IMSI attach/detach displays whether attach-detach-procedure is allowed in the cell (Y/N).

    Half rate channels displays whether half rate channels are supported in the cell (Y/N).

    C2 broadcast displays whether C2 values are broadcasted in the cell (Y/N).

    SI 7/8 broadcast displays whether system information 7 and 8 are broadcasted in the cell (Y/N).

    Cell broadcast displays whether cell broadcast is supported (Y/N).

    Call re-establish displays whether re-establishment is supported (Y/N).

    Early class mark send displays in idle mode whether early class mark (ECSC) sending is supported (Y/N). In dedicated mode (conversation) n/a is shown.

    2-ter messages displays in idle mode whether 2-ter messages are supported (Y/N). In dedicated mode (conversation) n/a is shown.

    Multi band reporting displays the multi band reporting decimal value (0,1,2,3) if supported.

    GPRS support displays whether GPRS is supported in the cell (Y/N).

    EDGE support displays whether EDGE is supported in the cell (Y/N).

  • 15 Nemo Handy Display Guide

    DTX displays whether discontinuous transmission is supported (Y/N).

    FER displays the frame error rate percentage.

    LQE displays the link quality estimate. Values range from 0 to 32.

    AMR Init Codec displays the AMR initial codec mode. Alternatives are 4.75, 5.15, 5.9, 6.7, 7.4, 7.95, 10.2, and 12.2.

    AMR ICMI displays the AMR initial codec mode indicator. Alternatives are N.A., Implicit, and Signalling.

    AMR Codecs displays the AMR active codec set. Alternatives are 4.75, 5.15, 5.9, 6.7, 7.4, 7.95, 10.2, and 12.2.

    AMR Codec UL/DL displays the AMR mode in uplink (UL) and downlink (DL) directions. Alternatives are 4.75, 5.15, 5.9, 6.7, 7.4, 7.95, 10.2, and 12.2.

    AMR Hyst 1-3 displays the AMR 1-3 hysteresis values in dB. Values range from 0 to 7.5 dB.

    AMR Thr 1-3 displays the AMR threshold values in dB. Values range from 0 to 31.5 dB.

  • 16 Nemo Handy Display Guide

    CellName displays the name of the serving cell based on BTS file.

    SiteName displays the base station name based on BTS file.

    Distance displays the distance to site based on BTS file.

    BTS CI displays the cell ID of the serving cell based on BTS file.

  • 17 Nemo Handy Display Guide

    VIEW 2/9 FOR GSM

    MSP displays the mobile station power level class. Values range from 0 to 32.

    RX Level displays the RX level full value when the mobile is in idle mode and the RX level sub value when a call is connected. Values range from -120 to -10 dBm.

    RX Quality displays the RX quality full value when the mobile is in idle mode and the RX quality sub value when a call is connected. Values range from 0 to 7.

    C/I displays the C/I value. Values range from -10 to 25.

    Coding DL/UL display the CS data channel coding for downlink/uplink direction. Alternatives are 9.6 and 14.4.

    #TS DL/UL displays the number of downlink/uplink timeslots.

    Tput DL/UL displays the downlink/uplink data transfer rate in kilobits per second.

    8-PSK M_BEP displays the bit error probability mean 8-PSK percentage.

    GMSK M_BEP displays the bit error probability mean GMSK percentage.

  • 18 Nemo Handy Display Guide

    VIEW 3/9 FOR GSM

    The table grid view displays the channel number, CI (cell identity), BSIC, C1, C2, LAC (location area code), and RX level for the serving (first on list) and neighbor channels.

  • 19 Nemo Handy Display Guide

    VIEW 4/9 FOR GSM

    The neighbor bar view for GSM displays the channel number, BSIC, and RX level for the serving and neighbor channels. The serving channel is displayed first on the list (in black).

    The neighbor line view for GSM displays the channel number and RX level for the serving and neighbor channels. The serving channel is displayed first on the list (in black). The RX level line for the serving channel is displayed in bold.

  • 20 Nemo Handy Display Guide

    VIEW 5/9 FOR GSM

    The inter-system bar and line views display for GSM the channel number, BSIC, and RX level for the serving and best neighbors and for UMTS the scrambling code, RSCP, and Ec/N0 for the active set and for best pilots in monitored set. The serving channel and the active set are displayed first on the lists (in black).

    Note that the values are displayed in real-time for the current system only. For the other system only the last values are displayed.

  • 21 Nemo Handy Display Guide

    VIEW 6/9 FOR GSM

    MSP displays the mobile station Tx power. Values range from 0 to 32.

    RX Level displays the RX level full value when the mobile is in idle mode and the RX level sub value when a call is connected. Values range from -120 to -10 dBm.

    RX Quality displays the RX quality full value when the mobile is in idle mode and the RX quality sub value when a call is connected. Values range from 0 to 7.

    LQE displays the link quality estimate. Values range from 0 to 32.

  • 22 Nemo Handy Display Guide

    VIEW 7/9 FOR GSM

    The data throughput line views display the application data throughput in kilobits per second for UL and DL directions. The value is also displayed as a line.

    Note that you need to have a data transfer on to see data in these views.

    #TS DL/UL display the number of downlink/uplink timeslots.

    Coding DL/UL display the CS data channel coding for downlink/upl...