motorised drums - .email salesautolinenetn web freephone 0800 37 55 the motorised drums for conveyor

Download Motorised Drums - .Email salesautolinenetn Web Freephone 0800 37 55 The motorised drums for conveyor

Post on 06-Jun-2018

212 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    MotorisedDrums

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    The motorised drums for conveyor systems type RL 072, MT 084 , MT 112 and MT 135 are productsspecially designed for motorising conveyor systems, they are easy to fit andintegrate most conveyors.

    To install and work with motorised drums the following instructions must be complied:

    - Motorised drums should normally be mounted horizontally.- Motorised drums must not be run without a belt or some other form of approved heat transfer system.

    Heat generated by the motorised drums must be dissipated, otherwise irreversible damage mayoccur to the transmission system. The crowned tube insures the belt remains central.

    - When assembled in brackets without rubber you should allow a gap ( 0.3 0.5 mm)between the end-cap faces and the bracket.

    - The belt should be adjusted just sufficiently to pull the belt and load without slip.- Ensure the correct connection in accordance with the electrical wiring schema.- To protect the motor from overheating. You must always connect the thermal protection, in series

    connection with the contactor coil.- We can supply motorised drums with special voltage, in stainless steel, or rubber lagging.

    RL /MT MOTORISED DRUMS

    Motorised drums for conveyor systems and check-outsThe motorised drums for conveyor systems RL 072, MT 084, MT 112 and MT 135 are products specially designed for motorising conveyor systems, they are easy to fit and integrate most conveyors.

    Operation & Maintenance

    To install and work with motorised drums the following instructions must be complied:

    Motoriseddrumsshouldnormallybemountedhorizontally

    Motoriseddrumsmustnotberunwithoutabeltorsomeother form of approved heat transfer system. Heat generated by the motorised drums must be dissipated, otherwise irreversible damage may occur to the transmission system. The crowned tube insures the belt remains central.

    Whenassembledinbracketswithoutrubberyoushouldallowa gap (0.3-0.5mm) between the end-cap faces and the bracket.

    Thebeltshouldbeadjustedjustsufficientlytopullthebeltand load without slip.

    Ensure the correct connection in accordance with the electrical wiring scheme.

    Toprotectthemotorfromoverheating.Youmustalwaysconnect the thermal protection, in series connection with the contactor coil.

    Wecansupplymotoriseddrumswithspecialvoltage,instainless steel or rubber lagging.

    2

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    The following charts show you the formula used to calculate the correct tension required topower conveyor systems. To select the appropriate motorised drum the tension (ortangential power) obtained must be inferior or equal to that indicated in technical tables,.

    Horizontal roller bed conveyor.

    Inclined roller bed conveyor.

    Horizontal slider bed conveyor.

    Inclined slider bed conveyor.

    T = Tension Tangential power ( N ).Pn = Total belt weight .) gK ( Pc = Total load weight .) gK ( Cn =Friction coefficient between belt and slider bed.a = Conveyor inclination angle.

    200.939690.34202

    Calculus Method

    The following charts show you the formula used to calculate the correct tension required to power conveyor systems. To select the appropriate motorised drum the tension (or tangential power) obtained must be inferior or equal to that indicated in technical tables.

    3

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    General features

    Diameter 72 mm. Standard length from 200 mm -

    1000 mm. Three-phase or Single-phase motors. Input power from 60 W - 95 W. Insulation F class. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 304. Lubricated for life with synthetic grease. Special options.

    Speedm/s0.780.670.600.420.300.780.670.600.420.300.20

    0.1750.160.140.130.110.10

    0.0830.0670.048

    L

    ==20

    70.9

    72

    = 20

    70.9

    R16

    21

    20

    33

    General features

    Diameter 72 mm. Standard length from 200 mm -

    1000 mm. Three-phase or Single-phase motors. Input power from 60 W - 95 W. Insulation F class. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 304. Lubricated for life with synthetic grease. Special options.

    Speedm/s0.780.670.600.420.300.780.670.600.420.300.20

    0.1750.160.140.130.110.10

    0.0830.0670.048

    L

    ==20

    70.9

    72

    = 20

    70.9

    R16

    21

    20

    33

    General Features

    Diameter72mm Standardlengthfrom200mm-1000mm Three-phaseorSingle-phasemotorsInputpowerfrom60W-95W InsulationFclass IP66protection Zinccoatedcrownedsteelshellorstainlesssteel304 LubricatedforlifewithsyntheticgreaseSpecialoptions

    RL 072 Motorised Drum

    4

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    General features Diameter 84 mm. Standard length from 269-1000 mm. Three-phase or Single-phase motors. Input power from 60 W-120 W. Insulation protection. IP 66 protection . Aluminium crowned shell or stainless

    steel 304. Lubricated for life with synthetic oil SAE

    68. Special options.

    Speedm/s0.110.100.080.190.160.150.120.770.590.490.460.390.240.190.160.15

    General Features

    Diameter84mm Standardlengthfrom269mm-1000mm Three-phaseorSingle-phasemotorsInputpowerfrom60W-120W Insulationprotection IP66protection Aluminiumcrownedshellorstainlesssteel304 LubricatedforlifewithsyntheticoilSAE68Specialoptions

    MT 084 Motorised Drum

    5

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    General features Diameter 112 mm. Standard length from 256 mm -

    1100 mm. Three-phase or Single-phase motors. Input power from 120 W -370 W. Insulation protection. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 306L. Lubricated for life with synthetic oil SAE

    68. Special options.

    Speedm/s0.810.690.500.360.310.260.200.150.120.081.050.910.810.690.500.360.310.260.200.150.12

    General features Diameter 112 mm. Standard length from 256 mm -

    1100 mm. Three-phase or Single-phase motors. Input power from 120 W -370 W. Insulation protection. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 306L. Lubricated for life with synthetic oil SAE

    68. Special options.

    Speedm/s0.810.690.500.360.310.260.200.150.120.081.050.910.810.690.500.360.310.260.200.150.12

    General Features

    Diameter112mm Standardlengthfrom256mm-1100mm Three-phaseorSingle-phasemotorsInputpowerfrom120W-370W Insulationprotection IP66protection Zinccoatedcrownedsteelshellorstainlesssteel306L LubricatedforlifewithsyntheticoilSAE68Specialoptions

    MT 112 Motorised Drum

    6

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    Speedm/s1.050.910.810.690.500.360.310.260.201.050.910.810.690.500.360.310.26

    General features Diameter 135 mm. Standard length from 300 mm-

    1100 mm. Three-phase or Single-phase motors. Input power from 120 W until 750 W. Insulation protection. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 306L. Lubricated for life with synthetic oil SAE

    68. Special options.

    Speedm/s1.050.910.810.690.500.360.310.260.201.050.910.810.690.500.360.310.26

    General features Diameter 135 mm. Standard length from 300 mm-

    1100 mm. Three-phase or Single-phase motors. Input power from 120 W until 750 W. Insulation protection. IP 66 protection . Zinc coated crowned steel shell or

    stainless steel 306L. Lubricated for life with synthetic oil SAE

    68. Special options.

    General Features

    Diameter135mm Standardlengthfrom300mm-1100mm Three-phaseorSingle-phasemotorsInputpowerfrom120W-750W Insulationprotection IP66protection Zinccoatedcrownedsteelshellorstainlesssteel306L LubricatedforlifewithsyntheticoilSAE68Specialoptions

    MT 135 Motorised Drum

    7

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    Speedm/s0.180.140.100.310.240.180.140.800.600.410.360.310.240.180.141.251.070.930.800.600.410.360.310.271.251.070.930.800.600.410.311.251.070.930.800.60

    Speedm/s0.180.140.100.310.240.180.140.800.600.410.360.310.240.180.141.251.070.930.800.600.410.360.310.271.251.070.930.800.600.410.311.251.070.930.800.60

    MT 135 Motorised Drum

    RI 50 Idler Drum

    8

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    MT 084 - MT 112 - MT 135

    RL 072

    MT 084 - MT 112 - MT 135

    RL 072

    Wiring Diagram

    Output Cable

    9

  • Email: sales@autoline.net.nz Web: www.autoline.net.nz Freephone: 0800 37 55 66

    Using a RL072FR or RL089 you can quickly and simply power handling systems and transport isolatedloads. It is lubricated with synthetic grease, no maintenance is required.

    To install and work with motorised drums the following instructions must be complied:

    - Motorised pulleys should be mounted a bit higher (between 1 and 2 mm) than idler drums, in thisway the optimal load drag is assured. Adjusting and levelling pulleys in the right form is veryimportant.

    - We suggest to use brackets which allow to adjust the height of the motorised pulleys.- Motorised pulleys must stop at least 2 seconds before turnover.- In base at the load verify the correct drums pitch.- Ensure the correct connection is in accordance with the electrical wiring diagram.- To protect the motor from overheating