messerschmitt hht v1.2 2008eng

5/25/2018 Messerschmitt HHT V1.2 2008eng

1/35

MesserschmittKEY CARD SYSTEMSContactfree Transponder Key Cards

orMagnetic Key Cards

Manual

Messerschmitt Hand Held TerminalHHT 2008 / V1.xx

Messerschmitt Systems GmbHMeiningerstrae 33

98544 Zella-Mehlis, Germany

TechnicalServiceandHot-Line- SupportTel.: 03682/854-0 Fax: 03682/854-22Website: www.messerschmitt.comE-mail: [email protected]

All rights, changes and errors reserved


2/35

HOCAS 2004 - Manual Handheld-Terminal

Version: May 2009 page 2

Directory

page

1. Introduction 3

2. Start of the Handheld Terminal application 4

2.1. The main menu 5

2.2. Changing Settings of the Handheld Terminal software 7

2.3. Reading out and displaying the programming of a reader unit 6

2.4. Loading and displaying the transactions of a reader unit 9

2.5. Initialisation of a reader unit 10

2.5.1. Initialisation of a guest reader 11

2.5.2. Initialisation of a group reader 12

2.5.3. Initialisation of a staff reader 13

2.5.4. Initialisation of special area readers 14

2.5.5. Initialisation of lift readers 15

2.5.6. Initialisation of locker locks 16

2.6. Parameterize reader units 17

2.7. Set the internal Clock of a reader unit 19

2.8 Timeslots of the special area readers and staff readers 20

3. The data interchange between Handheld and PC 21

3.1. The data transfer software hhtdock_v3.exe 21

3.2. The information dialog About Handheld manager 24

3.3. The configuration dialog Change settings of the Handheld 25

3.3.1. The configuration dialog Settings 26

3.3.2. The configuration dialog Power save 27

3.4. The dialog Update database of the Handheld 28

3.5. The dialog Load database from the Handheld 29

4. The menu Service 30

4.1. The menu File transfer 30

4.2. The menuPrepare SD Card 32

5. Installation directions 33

6. General hints 34

7. Optional: Set up the MFT as an Encoder 35


3/35



1. Introduction

The Messerschmitt Handheld TerminalHHT 2008 is used to initialize and to readout transactions of

reader units of the Messerschmitt Door Locking System HOCAS.

The device is scheduled for the contact free transponder card system and the magnetic card system. The

communication with the reader units can be made via serial cable connection or infrared.

The programs and the data base which included in delivery are located in the non volatile memory of the

Handheld Terminal on an external memory card.

Even after voltage breakdown, the data and the applications, which stored on the memory card, stay

there.

The following documentation refers to the handling of the Handheld Terminal as well as the related

PC Software hhtdock_v3.exe.

You can find technical details of the reader units in the corresponding descriptions.

The HHT 2008 disposes of a colour display with a

resolution of 320x240 pixels and an integrated touch

screen.

Included accessory in the delivery:

4 x NiMH AA Akku 2400mAh (already attached)

1 x wall plug transformer 230/ 9VDC-0,5A

1 x USB cabel 2m

1 x SD memory card 1GB (already attached)

The ports for the wall plug transformer and the USB

cable are located at the top of the device. Here you

also can find the infrared interface and the power

switch.

The SD card slot is located at the bottom of the

device.The accumulator panel and the RESET button are

located on the backside of the device.

Pay Attention!

Dont use the Messerschmitt HHT with customary

batteries!

Just use the original power adaptor (dont use power adaptors >9VDC)!


4/35



2. Start of the Handheld Terminal application

With switching on or resetting the Handheld Terminal you get to the login dialog.

Before using the handheld application, the users have to authenticate themselves.

The login data will be established with the HOCAS software on the Messerschmitt PC and will be

transferred during the data interchange with the Handheld Terminal.

Like in the program HOCAS2004, the users have to login with their name and password.

Ill. The login dialog

According to the user rights the menu items of the main menu will be fade in, if the login was successful.


5/35



2.1. The main menu

Over the different buttons, depending to the rights of the logged in user, the user can access to the

different functions of the application.

Ill. the main dialog

Button Transactions

Opens the Transactions dialog to readout and display the transactions of a reader unit.

Button Information

Opens the Information dialog to readout and display the parameters and configuration of a reader unit.

Button Initializing

Opens the Initializing dialog to configure reader units.

Button Parameter

Opens the dialog to readout and to set different parameters of a reader unit.

Button Date/Time

This dialog is for reading out and setting the internal clock of reader units.

Button Timeslots

Opens the dialog to readout and to set diverse timeslots of a reader unit.

Button Setup

Displays a dialog, where settings of the application can be changed.


6/35



Button About

A dialog with information about the software version and the contact addresses of the support.

Button Logout

The software will be terminated after confirmation.


7/35



2.2. Changing Settings of the Handheld Terminal software

The basic settings like the used interface will be made during the setup of the Handheld Terminal with the

PC Software. You also can directly change this settings with the Setup dialog in the Handheld

application.

ill. the settings dialog

Listbox Interface

Here, the user can choose the used communication interface. The possibilities are communication via

infrared ("IrDA") and communication via cable ("COM1: cable").

Listbox Card format

The card format has only effects to specific parameters during the initialisation of reader units and to

listed data, which are displayed in the information dialog.

Listbox Time until IDLE Mode

If there are no submissions on the Handheld Terminal during this time, the device switches automatically

in the IDLE mode the maximum time that can be choose are 5 minutes.

Listbox Time until Sleep Mode

If there are no submissions on the Handheld Terminal during this time, the device switches automatically

off the maximum time that can be choose are 10 minutes.

The Setup dialog loads the current settings. After quitting this dialog with the OK button, the set values

are immediately active.


8/35



2.3. Reading out and displaying the programming of a reader unit

The dialog Informationprovides information about the current configuration of the current reader unit. It

will be shown without limitation, the room number, the type of reader, the security numbers, the special

areas and the current date and time of the unit.

ill. Der Leserinformations-Dialog

Button Read

Reads out the configuration of the current reader unit and shows the information in a list.

Button Back

The dialog will be quit immediately.


9/35



2.4. Loading and displaying the transactions of a reader unit

Every card action on a reader unit will be saved in a special memory. This memory can be readout with

the help of the Transactions dialog. The containing entries will be referred to the current room, saved

into a spreadsheet and can be transferred later to the Messerschmitt PC to work on it.

ill. The Transactions dialog

The Transactionsdialog offers next to the reading out of saved transactions the possibility to analyse

happened access failures.

Button "Read"

It will be display the new entries since last reading out. The transactions memory of the reader units can

store a maximum of 400 actions.

If this memory is filled up, the oldest entries will be overwritten by the newest transactions.

Button "Back"



10/35



2.5. Initialisation of a reader unit

Every reader unit has to be initialized and to be configured after the installation. This procedure happens

with the menu item Initializing

In the process the reader gets the room number (e.g. number of the guest room for guest readers) as well

as additional data to limit the access (personal areas / groups and so on).

Furthermore the clock of the reader unit will be synchronized with the clock of the Handheld Terminal.

The data for the reader units have to define on the Messerschmitt PC with the application HOCAS2004

and have to be transferred via data transfer to the Handheld Terminal.

ill. Initializing dialog for guest readers

The initialisation of a reader unit starts with the choice of a room ( Room no.). Depending on the type of

the reader unit, it will be displayed a specified input mask, in which the access data for the chosen room

will be shown. This is used for the initialisation and data can be adjust, however the changed data will not

be written into to the Handheld Terminals data base. Because of that, modifications of the access data

should be done on the Messerschmitt PC. They can be transfer to the Handheld Terminal later.

The input field "log. no." has only relevancy for locker locks and is locked for all other types of devices.

ButtonInit

During the initialisation, the access data will be transferred to the reader unit.

Finally, the Transactionsmemory will be reset.

Button Back



11/35



2.5.1. Initialisation of a guest reader

Guest readers are generally reader units which are installed on guest doors. These doors only accept the

cards, that are encoded for that room and additional staff cards (e.g. Housekeeping), too.

ill. dialog INIT guest reader

The values that have to be set are stored in the database of the Handheld Terminal for each room and

will be set in the input mask of this dialog with the choice of a room number. Here you can change the

values afterwards if it is necessary, but changes will not be written into the database of the handheld!


12/35



2.5.2. Initialisation of a group reader

Group readers can be configured in away, that they accept guest cards from several rooms, which is

suitable to manage suites. The assignment, which guest card will be accepted, have to be done with the

help of the management software HOCAS on the System PC.

ill. Dialog INIT group reader

The values inclusive the guest room relationship, that have to be set are stored in the database of the

Handheld Terminal and will be loaded in an internal puffer with the choice of a room number.


13/35



2.5.3. Initialisation of a staff reader

Staff readers check only the special areas besides the temporary limited permissions of a card.

In distinction from special readers, staff readers dont accept guest cards.

ill. INIT a staff reader





14/35



2.5.4. Initialisation of special area readers

Special area readers check, if a temporal valid access card has the permission to access a special area.

If the area checking is disabled (special area = none), every valid card of the house will be accepted.

Because of that, special area readers are often used on main entrances.

ill. INIT a special area reader





15/35



2.5.5. Initialisation of lift readers

The initialisation of a lift reader always depends on the structural conditions of the current house.

ill. INIT a lift reader




Choice Special area control

Only the floors with the correct permissions to the encoded special areas will be approached

Choice Floor control without tableau activation

The floor will be directly approach without an input on the tableau, if a guest card is used.

Here the tableau is disabled. The relevant floor will be detected by the room number of a guest card. If

staff cards are used, the tableau is enabled.

Choice Floor control with tableau activation

The floor will be directly approach without an input on the tableau, if a guest card is used. Additional the

tableau is enabled for entries, too. The relevant floor will be detected by the room number of a guest card.

If staff cards are used, the tableau is enabled.

The time of the activation of the tableau will be display in the field Time of activation. (stated in seconds)


16/35



2.5.6. Initialisation of locker locks



values afterwards if it is necessary, but these will not be taking over in the database of the handheld!

ill. INIT a locker lock

Guest locker choose mode

Configures the mode of a guest locker.

variable (every valid guest card)

If the locker is opened, he accepts any guest card.

static (only assigned guest card)

Only guest cards, where the locker number is set, can open the locker

Staff locker

The locker can be used with a staffcard. The staffmember has to be assigned manually by choosing from

the drop-down list.


17/35



2.6. Parameterize reader units

Additional to the data for the initialisation, the reader unit needs information about the type of opening the

door (e.g. how and how long should be open). These values are pre-defined and can be configured in the

menu Parameter.

ill. the Parameter dialog

Button "Read all parameter"

Displays the current values of the reader unit and puts them in the input mask.

Button "Set all parameter"

All displayed values in the input mask will be transferred back to the reader unit.

The changes will be active immediately.

Pay Attention: Before the values can be written, the current values of the reader unit have to be loaded

(Button "Read all parameter").

Button "Back"

The dialog will be quit immediately. Changes of the parameters of a reader unit will not be made.

Duration door open

Duration in milliseconds in which the door or the door contact will be switched on and the green or blue

LED will be light up.


18/35



Opening mode

This choice gives information about the kind of installation of the Key Card unit. That means, if the unit is

placed on the door or placed on the wall (for special doors). For wall installations, a potential-free contact

will be switched during the green LED is lighted up.

Daylight saving

These 2 values give information about the intercalary months from the standard to the daylight time and

from the daylight to the standard time.

The values are needed for the automatic correction of the internal reader clock. If there is no value set,

the automatic time correction is disabled.

Alternate opening

This value defines weather the reader opens and closes the door alternate. That means, the door will be

stayed open till a valid card is used to close the door.

Group reader: check area

Only for card format 4: The reader unit checks the staff areas, too.

DND: staff card opens the door

Contrary to the standard, the staff can opens a door, when the Do not disturb is set.

DND: Guest can not open door

For special doors (e.g. conference rooms) it is maybe necessary, that guest cards can not open the door,

when the Do not disturb is set.

HHT: wakeup by IrDA

This parameter activates the automatic wakeup, when data is detected via the IrDA interface.


19/35



2.7. Set the internal Clock of a reader unit

Every reader unit has got an internal clock. After a battery change, that means when the power supply of

a reader unit was interrupted, the clock has to be corrected.

It can be made with this Date/Time dialog or with the help of a Date/Time card

ill. the Date/ Time dialog

Button Read

This option reads out and displays the internal clock of the current reader unit.

Button Set

This option corrects the internal clock of the current reader unit with the given values for date and time.

Button Back


Pay Attention: The internal reader unit has to be corrected, if the power supply was interrupted (e.g.

battery change). The clock will automatically be set with the initialisation of reader units via Handheld

Terminal.


20/35



2.8. Timeslots of the special area readers and staff readers

The reader units save the timeslots in form of a spreadsheet with 32 entries. The entries 0 to 29 are used

for the staff entrance.

Entry 30 describes the time period for the automatic door opening and the entry 31are used for the guest

entrance on special area readers. These values can be set here.

Pay Attention:There will be encoded the number of the timeslot on the staff cards, not the times.

Because of that, the timeslots on the System PC have to be the same like the timeslots in the reader units

and the timeslots, which are set in the Handheld Terminal. Potential changes have to be changed first on

the System PC. Values, that are changed via Handheld Terminal will not be stored in the handheld

terminal and so, they can not transferred to the System PC

Examples: Entrance for the whole day: 00:00 - 24:00

No automatic Locking : 24:00 - 24:00 (Timeslot 30)

Automatic Locking at 18:00,but no automatic opening: 24:00 - 18:00 (Timeslot 30)

ill. The timeslot dialog

Button Read

The dialog reads out the timeslot of the current reader unit and displays it on the screen.

Button Set

This option transfers the displaying timeslots of the list to the reader unit.

Button Back



21/35



3. The data interchange between Handheld and PC

The data interchange between the Handheld Terminal HHT 2008 and the Messerschmitt System PC

happens via USB.

When the HHT is connected to the PC for the first time, the new hardware will be detected and the USB

driver has to be installed.

This Driver you can be found on the installation CD in the directory.

\Drivers\Messerschmitt USB Device Driver

After the installation of the USB driver, a new COM port will be set in the windows device manager.

Messerschmitt Systems AG USB -Device (COM3) (Example!)

3.1. The data transfer software hhtdock_v3.exe

With the help of the data transfer software hhtdock_v3.exe data can exchanged between the HHT and

the System PC. Also, the handheld can be initialized and configured with this software.

ill. Main screen menu of the hhtdock_v3.exe

At the start of the program, the configured COM interface will be searched.

If it will not be detected automatically, the interface can be set manual with the menuConnection

Connection Settings.

ill. Main menu of hhtdock_v3.exe


22/35



With the button Scan for device you can search for the handheld again or you can choose manually a

COM port with the combo box..

ill. Menu Connection settings..

Click OKto use the chosen port.

If the Handheld Terminal is detected, the main screen will be display in a blue colour with a hint in the

right top corner connected.

If the basic colour is red and the hint shows not connected, the connection could not established.

In this case, make sure that the USB driver is installed correctly and execute a reset on the HHT. For this

purpose, click the button on the back of the device and after that; execute the Connection settings

dialog again.


23/35



The menu bar is placed on the top of the main window.

ill. the menu of hhtdock_v3.exe

Here you can start all functions, which you can also start by clicking the big buttons in the centre of the

window.

The buttons

Transfers the data base to the HHT. The matching of data is always necessary when

modifications on the PCs data base result to differences to the configuration of the

reader units.

Transfers the transactions which are saved in the HHT to the PC.

The transactions will be write depending on the date into the monthly log files

Two queries has to be confirmed:

1. Shall all transactions be transferred

2. Shall the transaction spreadsheet on the HHT be cleared after data transfer

Shows the configuration dialog

Opens the service dialog with additional functions

Quits the application


24/35



3.2. The information dialog About Handheld manager

ill. the about window

From the main window you can reach the information window to the application.

Here you get information of the program version, the used interface of the HHT and the contact address of

the company Messerschmitt Systems AG.


25/35



3.3. The configuration dialog Change settings of the Handheld

This dialog is for the configuration of the connected Handheld Terminal.

The different buttons on the bottom of this menu have the following functions.

ill. the configuration dialog

Button "Write configuration"

This function writes the settings to the handheld device after a confirmation.

Button "Read configuration"

Reads the current settings of the handheld device

Button "Defaults"

Set the configuration to default values.

Button "Back"

Close the dialog.


26/35



3.3.1. The configuration dialog Settings

ill. the configuration dialog Settings

Input field "Device name"

Here you can declare a device name. The name is limited to 16 characters.

Combo box "Language"

Here you can change the language of the texts and dialogs that are displayed in the handheld application.

You can choose between English and German.

Combo box "Interface"

Here you can choose your interface for the communication with the reader units.

According to the interface on your reader units, you can choose between Cableand IrDA.

Label "Hotelcode"

Here the unique project code of your HOCAS System is presented. This code is allocated by the

company Messerschmitt and cannot be changed by the customer.

Label "Cardformat"

In the card format 4(2000) is the number of used special areas 40.

In the card format 5(2004) this value is 32 for guest cards and 56 for staff cards.

Furthermore there are used 5 extended card types in the card format 5. This setting cannot be changed

and is administrated by the System PC.

Combo boxes "Daylight saving time"

Here you set the months in which third weekend the switch from the daylight and standard time isexecuted on the reader units. The European standard is March and October. You also can deactivate this

setting.


27/35



3.3.2. The configuration dialog Power save

ill. the configuration dialog Settings

Combo box "IDLE mode after" Standby

If there are no user inputs on the touchscreen of the Handheld Terminal during this time, the device

switches automatically in the IDLE mode The time limit can be set to a maximum of 5 minutes.

Combo box "Power down after" - Switch Off

If there are no user inputs on the touchscreen of the Handheld Terminal during this time, the device

switches automatically off The time limit can be set to a maximum of 5 minutes.

Fader Display (brigthness)"

Here you can change the brightness during standard mode and the the IDLE mode.

standards: maximum : Level 5 maximum

IDLE mode : Level 1 minimum


28/35



3.4. The dialog Update database of the Handheld

With the help of this menu the data bases of the System PC will be transferred to the

Handheld Terminal, if the following query will be confirmed with Yes.

ill. Confirmation

If data already exists on the HHT, a further query will ask you, if you want to overwrite the existing data.

Confirm the question with the standard Yes to All

.

ill. Confirmation File already existing

Afterwards the necessary files will be transferred to the Handheld Terminal

ill. action Copying file(s)


29/35



3.5. The dialog Load database from the Handheld

The transactions, that has been read in from the reader units will be saved in

the HHT. This information can be transferred with the help of this menu to the

System PC. With the application HOCAS menu protocols you can

manage, select, edit and print out the access data.

After confirmation of a query, the access data will be transferred to the System PC.

ill. action Apply transactions


30/35



4. Menu Service

The menu Service has got 3 tabs with additional and helpful functions.

Click OK to left the menu and return back to the main menu.

4.1. Menu File transfer

ill. menu File transfer

A right click with the mouse in one of the two lists opens a context menu, which offers additional functions

to manage files and listings.

Refresh Updates the displayNew folder Creates a new folder

Copy Marks the chosen files for copy.

Paste Copies the marked files to the current position in the file

system

Delete Deletes the chosen files / listings

Abb. 1 Das Datei-MenRename Renames the current file / listing

With double click on a file, the preview will be executed.Data base spreadsheets (DBase or Paradox spreadsheets) will be shown in a special dialog.


31/35



Further Buttons

Transfers the marked files to the System PC

Transfers the marked files to the Handheld Terminal.

4.2. Menu Prepare SD Card

ill. menu Prepare SD card

If it is necessary to use a new memory card (because the provided card is damaged), the card has to be

format before you can use it. You can do this with clicking on the button Quick format in the menu tab

Prepare SD card. With the Button Detect you can analyze the deployed memory card.


32/35



4.3. Menu Screenshot

ill. menu Screenshot

The functions Make screenshot of handheld display and Save screenshot to file represent tools to

save screenshots of the HHT on the System PC.

For example, the currently read out access data can be save as a bitmap on the PC.


33/35



5. Installation directions

According to your system configuration, you have to follow the following installation hints before

you can use the Handheld Terminal:

I. If you use a Messerschmitt System without any according USB device (e.g. USB encoder),

you have to install the USB drivers for the HHT. You can find it on the provided installation

disc. To this, connect the HHT to the PC. The following dialog will be shown:

Follow the instruction of the install manager and give the following path to the driver!

E:\Drivers\Messerschmitt USB Device Driver\

(The drive character depends on your system configuration)

II. To install the application hhtdock_v3.exe insert the provided installation disc in you cd /

dvd drive. The installation dialog will be start automatically. You can also start the setup by

clicking the setup.exe

III. The last is to reregister your complete system, so that the application can be used with the

other system modules. For that, started the HOCAS application and choose in the start

window the option Licence. Put in the field the new licence code, which you can find in the

text file Licence.txt in the folder Licence on your installation disc


34/35



If you have ordered a complete Messerschmitt System with a Handheld Terminal, normally

the PC, the Handheld and the attached software will be installed and preconfigured.

6. General hints

Dont use the Messerschmitt HHT with customary batteries

The charging period is 12 hours

To charge the device you have to connect to the power adaptor and to switch on the device

temporary

For the communication with the provided docking software hhtdock_v3.exe the device has to be

connected via USB

Make sure, that the device gets additional power from the power supply, if the device is connected

to the pc. Use the provided power supply adaptor, so that the proper working is guaranteed

Make sure, that the Daylight saving time is set correctly in the settings dialog of the docking

software hhtdock_v3.exe. If you didnt need this option, disable it. (page 26)


35/35



7. Optional: Set up the MFT as an Encoder

The Messerschmitt Handheld in the version Messerschmitt MFT/Transcoder Version 1.xx offers beside

the initialisation and analyzing tools for Messerschmitt reader units the opportunity to encode cards.

To use the device as an encoder, you have to follow the instructions listed below:

Make sure, that the docking software hhtdock_v3.exe is notrunning

Connect the MFT with the power supply and with the pc via the USB-interface

In the HOCAS configuration file C:\Windows\HOC7000.ini you have to define the COM-Port of

the device as an encoder interface:

>>>>>>>>>>>>>>>>>>>>>>

[CODBUS]Exist=1Bus1=MFT,\\.\COM3;Bus2=\\.\COM39,9600,8,O,1,50;Bus3=\\.\COM7,9600,8,O,1,20;Bus4=\\.\COM8,9600,8,O,1,20

Device1=1,1,,6;Device2=2,1,,6;Device3=3,1,,6;Device4=4,1,,6

messerschmitt hht v1.2 2008eng

Documents