measurement of target thickness by a nuclear track technique

2
Nucl. Tracks Radiat. Meas., Vol. 19, Nos 1--4, pp. 597-598, 1991 Int. J. Radiat. AppL lnstvum., Part D Printed in Great Britain 0735-245X/91 $3.00 + .00 Pe~mon Press plc NEASURKHENT OF TARGET TNICENKSS BY A NUCLEAR TRACK TECHNIQUE K.K.Dwivedi, S.Ghosh and J.Raju Department of Chemistry, North-Eastern Hill University, Shillong - 793 003, India. ABSTRACT A new application of the nuclear track technique for the measurement of target thickness is presented here. A well collimated beam of heavy ions is allowed to penetrate through thin metal targets and the energies of the heavy ions emerging out of these targets are obtained from the maximum etchable track lengths in a suitable track detector using energy-track length calibration curve. Target thickness is then determined from range-energy calibration plots. In this paper we discuss this track technique and highlight its scope. KETWORDS Target thickness, range-energy calibration, heavy ions, track technique. INTRODUCTION Target thickness measurements are of paramount importance in nuclear physics to determine the cross-section of nuclear reactions, the thickness of backings and windows or the energy lost by ions while passing through degrader foils. In order to evaluate these parameters correctly it is necessary to determine the target thickness as accurately as possible. Different methods(Kato, 1969) which have been used to determine the target thickness suffer from one drawback or the other-like reproducibility of the known cross-section and destruction of targets in thickness measurements. Also a high flux of a-particles can change the target properties by radiation damage and thermal heating. It is therefore necessary to evolve a technique which is accurate and is also non-destructive(Xu Guoji et al., 1985). Bearing these in mind, we present here, a new application of the nuclear track technique to measure target thickness using a heavy ion beam. THE TRACK TECHNIQUE Neasurement of target thickness by the proposed nuclear track technique involves two simple steps. Step 1 - The Energy-Track Length Calibration of the Detector First of all a sensitive track detector is calibrated in terms of maximum etchable track length (L) and energy (E) of the heavy ions. k third order polynomial may be used to fit the track length data and is expressed by n~3 E(MeV/u) ~ ~ anLn(~m) (I) Step 2- The Ranqe-Eneray Calibration of Target Element This calibration can be obtained from the available experimental data on range and energy of a heavy ion in the target material. Again a third order polynomial produces the best fit for the range-energy data. It may be expressed as 597

Upload: kk-dwivedi

Post on 26-Jun-2016

214 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: Measurement of target thickness by a nuclear track technique

Nucl. Tracks Radiat. Meas., Vol. 19, Nos 1--4, pp. 597-598, 1991 Int. J. Radiat. AppL lnstvum., Part D Printed in Great Britain

0735-245X/91 $3.00 + .00 Pe~mon Press plc

NEASURKHENT OF TARGET TNICENKSS BY A NUCLEAR TRACK TECHNIQUE

K . K . D w i v e d i , S .Ghosh and J . R a j u

D e p a r t m e n t o f C h e m i s t r y , N o r t h - E a s t e r n H i l l U n i v e r s i t y , S h i l l o n g - 793 003, I n d i a .

ABSTRACT

A new a p p l i c a t i o n o f t h e n u c l e a r t r a c k t e c h n i q u e f o r t h e m e a s u r e m e n t o f t a r g e t t h i c k n e s s i s p r e s e n t e d h e r e . A w e l l c o l l i m a t e d b e a m o f h e a v y i o n s i s a l l o w e d t o p e n e t r a t e t h r o u g h t h i n m e t a l t a r g e t s and t h e e n e r g i e s o f t h e h e a v y i o n s e m e r g i n g o u t of t h e s e t a r g e t s a r e o b t a i n e d f rom t h e maximum e t c h a b l e t r a c k l e n g t h s i n a s u i t a b l e t r a c k d e t e c t o r u s i n g e n e r g y - t r a c k l e n g t h c a l i b r a t i o n c u r v e . T a r g e t t h i c k n e s s i s t h e n d e t e r m i n e d f rom r a n g e - e n e r g y c a l i b r a t i o n p l o t s . I n t h i s p a p e r we d i s c u s s t h i s t r a c k t e c h n i q u e and h i g h l i g h t i t s s c o p e .

KETWORDS

T a r g e t t h i c k n e s s , r a n g e - e n e r g y c a l i b r a t i o n , h e a v y i o n s , t r a c k t e c h n i q u e .

INTRODUCTION

T a r g e t t h i c k n e s s m e a s u r e m e n t s a r e o f p a r a m o u n t i m p o r t a n c e i n n u c l e a r p h y s i c s t o d e t e r m i n e t h e c r o s s - s e c t i o n o f n u c l e a r r e a c t i o n s , t h e t h i c k n e s s o f b a c k i n g s a n d windows o r t h e e n e r g y l o s t by i o n s w h i l e p a s s i n g t h r o u g h d e g r a d e r f o i l s . I n o r d e r t o e v a l u a t e t h e s e p a r a m e t e r s c o r r e c t l y i t i s n e c e s s a r y t o d e t e r m i n e t h e t a r g e t t h i c k n e s s as a c c u r a t e l y a s p o s s i b l e . D i f f e r e n t m e t h o d s ( K a t o , 1969) which h a v e been u s e d t o d e t e r m i n e t h e t a r g e t t h i c k n e s s s u f f e r f rom one d r awback o r t h e o t h e r - l i k e r e p r o d u c i b i l i t y of t h e known c r o s s - s e c t i o n and d e s t r u c t i o n of t a r g e t s i n t h i c k n e s s m e a s u r e m e n t s . A l s o a h i g h f l u x o f a - p a r t i c l e s c an c h a n g e t h e t a r g e t p r o p e r t i e s by r a d i a t i o n damage and t h e r m a l h e a t i n g . I t i s t h e r e f o r e n e c e s s a r y t o e v o l v e a t e c h n i q u e w h i c h i s a c c u r a t e and i s a l s o n o n - d e s t r u c t i v e ( X u G u o j i e t a l . , 1 9 8 5 ) . B e a r i n g t h e s e i n m i n d , we p r e s e n t h e r e , a new a p p l i c a t i o n o f t h e n u c l e a r t r a c k t e c h n i q u e t o m e a s u r e t a r g e t t h i c k n e s s u s i n g a h e a v y i on beam.

THE TRACK TECHNIQUE

N e a s u r e m e n t of t a r g e t t h i c k n e s s by t h e p r o p o s e d n u c l e a r t r a c k t e c h n i q u e i n v o l v e s two s i m p l e s t e p s .

S t e p 1 - The E n e r g y - T r a c k L e n g t h C a l i b r a t i o n of t h e D e t e c t o r

F i r s t of a l l a s e n s i t i v e t r a c k d e t e c t o r i s c a l i b r a t e d i n t e r m s of maximum e t c h a b l e t r a c k l e n g t h (L) and e n e r g y (E) o f t h e h e a v y i o n s . k t h i r d o r d e r p o l y n o m i a l may be u s e d t o f i t t h e t r a c k l e n g t h d a t a and i s e x p r e s s e d by

n~3 E(MeV/u) ~ ~ anLn(~m) (I)

S t e p 2- The R a n q e - E n e r a y C a l i b r a t i o n of T a r g e t E lement

T h i s c a l i b r a t i o n can be o b t a i n e d f rom t h e a v a i l a b l e e x p e r i m e n t a l d a t a on r a n g e and e n e r g y o f a h e a v y i o n i n t h e t a r g e t m a t e r i a l . A g a i n a t h i r d o r d e r p o l y n o m i a l p r o d u c e s t h e b e s t f i t f o r t h e r a n g e - e n e r g y d a t a . I t may be e x p r e s s e d as

597

Page 2: Measurement of target thickness by a nuclear track technique

598 K . K . DWlVEDI et al.

m=3 R(gm) = ~ = bmEm (MeV/u) (2)

where b m r e p r e s e n t s a s e t of c o e f f i c i e n t s .

I f t h e i n i t i a l e n e r g y of a h e a v y i o n be E i t h e n t h e t r a n s m i t t e d e n e r g y , E x, of t h e h e a v y i o n a f t e r p a s s i n g t h r o u g h a t a r g e t t h i c k n e s s ' x ' may be o b t a i n e d u s i n g e q . ( 1 ) . From e q . ( 2 ) one g e t s t h e v a l u e s of r a n g e R f o r a c o r r e s p o n d i n g v a l u e of e n e r g y E of t h e h e a v y i o n s . The t a r g e t t h i c k n e s s may t h e n be e a s i l y o b t a i n e d f rom

x = R(E i) - R(E X) (3)

where R(E i) and R(E x) are the ranges of heavy ions corresponding to the initial E i and transmitted energy E x.

EXPERIMENTAL REQUIREMENTS

T a r g e t s of v a r y i n g t h i c k n e s s may be s e l e c t e d and t h e n mounted on a s u i t a b l e t r a c k d e t e c t o r . The t a r g e t - d e t e c t o r a s s e m b l y may t h e n he i r r a d i a t e d by a w e l l c o l l i m a t e d low f l u x beam of h e a v y i o n s a t a s u i t a b l e a n g l e ( e g . 4 5 ° ) . Two s e t s of i r r a d i a t i o n s may t h e n be p e r f o r m e d - o n e w i t h and t h e o t h e r w i t h o u t t a r g e t s . The two s e t s o f d e t e c t o r s may t h e n b e c h e m i c a l l y e t c h e d t i l l t h e t r a c k t i p s a r e r o u n d e d . M e a s u r e m e n t s may be done u s i n g an o p t i c a l m i c r o s c o p e and t h e maximum e t c h a b l e t r a c k l e n g t h s may be o b t a i n e d u s i n g e q u a t i o n g i v e n by Dwived i and M u k h e r j i ( 1 9 7 9 ) .

DISCUSSION

The t r a c k t e c h n i q u e f o r m e a s u r e m e n t o f t a r g e t t h i c k n e s s r e q u i r e s two t y p e s o f c a l i b r a t i o n s (a) Between h e a v y i o n e n e r g y and t h e maximum e t c h a b l e t r a c k l e n g t h i n a s e n s i t i v e t a r c k d e t e c t o r and (b) b e t w e e n r a n g e e n e r g y o f s ame h e a v y i o n i n a r e q u i r e d t a r g e t m a t e r i a l . F r o m t h e s e c a l i b r a t i o n s t h e b e s t s e t of c o e f f i c i e n t s a r e e v a l u a t e d by u s i n g s u i t a b l e p o l y n o m i a l f u n c t i o n s . The t h i c k n e s s o f a t a r g e t may s i m p l y be o b t a i n e d by ( i ) m e a s u r i n g maximum e t c h a b l e t r a c k l e n g t h of t h e t r a n s m i t t e d i o n s i n t h e t r a c k d e t e c t o r , ( i i ) d e t e r m i n i n g i o n e n e r g y f rom eq . ( 1 ) , ( i i i ) f i n d i n g r a n g e s of h e a v y i o n s i n t a r g e t m a t e r i a l f rom eq . (2) and f i n a l l y ( i v ) f rom e q ( 3 ) , t h e t a r g e t t h i c k n e s s may he d e r i v e d . Thus i n t h e p r o p o s e d t r a c k t e c h n i q u e w i t h t h e h e l p of r eadymade c a l i b r a t i o n c u r v e s one can d e t e r m i n e t h e t h i c k n e s s of t h e t a r g e t s by s i m p l y m e a s u r i n g t h e maximum e t c h a b l e t r a c k l e n g t h s o f h e a v y i o n s a f t e r p a s s i n g t h r o u g h t h e t a r g e t s . The p r o p o s e d t r a c k t e c h n i q u e h a s b e e n e m p l o y e d t o m e a s u r e t h i c k n e s s s e v e r a l A l - t a r g e t s u s i n g 238U i o n s and Z n P - g l a s s d e t e c t o r s . The d e t a i l s of e x p e r i m e n t and r e s u l t s a r e n o t p r e s e n t e d h e r e due to page l i m i t a t i o n s and a r e b e i n g p u b l i s h e d s e p e r a t e l y .

CONCLUSION

I t may be c o n c l u d e d t h a t t h i s t r a c k t e c h n i q u e i s s i m p l e , n o n - d e s t r u c t i v e and c a p a b l e o f y i e l d i n g f a i r l y a c c u r a t e r e s u l t s . A low d o s e of h e a v y i o n s i s r e q u i r e d compared t o a h i g h f l u x of = - p a r t i c l e s w i t h t h e i r a t t e n d a n t d r a w b a c k s l i k e r a d i a t i o n damage, t h e r m a l h e a t i n g t o name a f e w . M o r e o v e r , h e a v y i o n s b e i n g s u p e r i o r p r o j e c t i l e s p r o d u c e v e r y l i t t l e s t r a g g l i n g and n e g l i g i b l e l a r g e a n g l e s c a t t e r i n g . I t i s e n v i s a g e d t h a t t h o s e c e n t r e s w h e r e h e a v y i o n b e a m s a r e r o u t i n e l y a v a i l a b l e , n u c l e a r t r a c k t e c h n i q u e may p r o v e t o be q u i t e c o n v e n i e n t and p r e f e r a b l e o v e r ~ - p a r t i c l e s f o r m e a s u r i n g t a r g e t t h i c k n e s s .

REFERENCES

Dwlvedi. K.K and S. Mukherji (1979). Track lengths of heavy ions in solid dielectric track detector. Nucl.Instrum. Meth., 161, 317-326.

Kato. S (1969). Methods of Target thicness measurements. Nucl. Instrum. Meth., 75, 293-296.

Xu Guoj i , Zhao Yuhua, Zheng Shengnan and Xu Yongcbeng (1985). Determinat ion of thicnesses and impurities of targets by measuring back-scattered particles from 2 MeV 4He +- bombardment. Nucl. Instrum. Meth., A236, 627-629.