md-203 · 2018-01-22 · ppb ppb ppb ppb ppb at time of shipment, v s ±5% static load ±5% static...
TRANSCRIPT
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 1 of 8
MD-203I2C Interface Oven Controlled Crystal Oscillator
Preleminary version
• Surface Mount package• Low Profile Compact Package• Standard frequency: 10, 20 MHz• Temperature stability to 8 ppb• Aging rate to 0.5 ppb/day• I2C interface with frequency coefficients, temperature sensor for additional correction
• Base stations• Test equipment• Synthesizers• LTE Basestation
Features Applications
MD-203
Frequency Stabilities1 ( 10 & 20 MHz)
Parameter Min Typical Max Units Conditionvs. operating temperature range (referenced to +25°C, uncompensated)
-8-8
+8+8
ppbppb
-20 to +70°C-40 to +85°C
Residual error compare to fit curve
-0.3 0.3 ppb
Improved Frequency versus temperature F(T) performance obtained using on board temperature sensor (T) and frequency vs. temperature coefficients (An)stored in EEPROM, using formula:F(T)=A4T4+A3T3+A2T2+A1T+A0
Initial tolerancevs. supply voltage changevs. load changevs. aging / dayvs. aging / yearvs. aging / 10 year
-3-4-3
-0.5-60
-500
+3+4+3
+0.5+60
+500
ppmppbppbppbppbppb
at time of shipment, VS ±5% static
Load ±5% static after 30 days of operation after 30 days of operationafter 30 days of operation
holdover µsec over 8 hours and 5°C temp jump @ T0
start up time
Warm-up time 5 minutes to ±100ppb of final frequency (1 hour reading) @ +25°C
Performance Specifications
The MD-203 is a Vectron module that contains a medium size ovenized crystal oscillator and an I2C interface that communicateswith an onboard EEPROM and temperature sensors. The interface enables the customer to improve upon the alreadyexceptional stability of the oscillator. Provided in a fully hermetic 25 x 25 mm package mounted on a SMD spreader board. The device is capable of aging rates of 0,5 ppb/day and temperature stabilities of 8ppb from -40 to 85 °C. Use of the information provided in the I2C interface provides a cost effective means of improving stability by as much as a factor of 10 depending upon environmental conditions.
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 2 of 8
Performance Specifications
Supply Voltage (Vs)
Parameter Min Typical Max Units ConditionSupply voltage (standard) 4.75 5.0 5.25 VDC
Power consumption3.25 Watts during warm-up
1.5 Watts steady state @ +25°C
RF OutputSignal [standard] HCMOS
Load 15 pF
Signal Level (Vol) 0.8 VDC with Vs=5.0V and 15pF Load
Signal Level (Voh) 3.4 4.6 VDC with Vs=5.0V and 15pF Load
rise time 10 ns
fall time 10 ns
Duty Cycle 40 60 % @ (Voh-Vol)/2
Frequency Tuning (EFC)Tuning Range Fixed OCXO; No adjust
Additional Parameters
Phase Noise3
-104-129-140-145-153-155
-90-120-130-140-148-150
dBc/HzdBc/HzdBc/HzdBc/HzdBc/Hz dBc/Hz
1 Hz10 Hz
100 Hz1 kHz
10 kHz100khz
@ 10MHz
Weight 12 g
Processing & Packing Handling & Processing Note
EEPROM (SCL, SDA) Pin 2; Pin 7
Parameter Min Typical Max Units ConditionI2C Bus Voltage 2,8 VDC
DC Electrical Characteristics
High Level Input Voltage (Vih) 0.7* VI2C VI2C +0.3 Vdc SDA (internally pulled-up to VI2C with a 22kohm resistor) and SCL
Low Level Input Voltage (Vil) -0.3 0.3 VI2C Vdc SDA (internally pulled-up to VI2C with a 22kohm resistor) and SCL
Electrical Characteristic Product is to communicate via industry stan-dard I2C bus timing. I2C is a Phillips Semicon-ductor registered trademark.
SCL Clock Frequency 0 100 kHz
Communication Product is to communicate via industry stan-dard I2C bus timing. I2C is a Phillips Semicon-ductor registered trademark.
EEPROM I2C Device 7-bit Address: 1010100
For full EEPROM Map please contact factory
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 3 of 8
Reference Voltagesupply voltage (Vs) 7.0 V with Vs= 5.0 VDC
Output Load 50 pF
Operable Temperature Range -40 +85 °C
Storage Temperature Range -40 +85 °C
Absolute Maximum Ratingssupply voltage (Vs) 7.0 V with Vs= 5.0 VDC
Output Load 50 pF
Operable Temperature Range -40 +85 °C
Storage Temperature Range -40 +85 °C
A ( 5 : 1 )
A
2,5
212,70,1
19,050,1
6,350,1
19,050,1
25,4
0,2
25,60,2
H+-1G334
0,1
SEATING PLANE
33
0,2
Dimensions in mm
Outline Drawing / Enclosure
Pin Connections1 RF Output
2 EEPROM SDA (I2C)
4 GND
6 N.C
7 EEPROM SCL (I2C)
13 Vref (reference voltage)
15 N.C.
17 Vtemp output
19 Supply Voltage Input (Vs)
MD-203Height “H” cover material
11.3 metal
tbd
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 4 of 8
Standard Shipping Method (MD-203 )
Recommended Reflow Profile
IPC/JEDEC J-STD-020 (latest revision)Additional Information:This SMD oscillator has been designed for pick and place reflow soldering.SMD oscillators must be on the top side of the PCB during the reflow process.
Additional Environmental Conditions
Enclosure Type Tape Width W (mm) Quantity per meter Quantity per reel Dimension P
MD-203 44 31.25 150 32
Maßangaben in mm: Dimension in mm:
A, B und K Maße von Bauelement abhängig A, B und K are dependent uppon component dimensions
Fertigungstoleranzen entsprechen der DIN IEC 286-3 production tolerance complying DIN IEC 286-3
P
W
1.75±0.1
R 0.75
4.0
Lage im GurtPosition in tapePin1
A
B B
AbwickelrichtungUnwinding direction
0.20
±0.0
5
A
All dimensions in millimeters unless otherwise stated
XXXXX
XXXXX
Bei W < 32mm nur obere Lochreihe vorhandenif W < 32mm only upper hole line existent
A
Schnitt B - B
B
K
Schnitt A - A
Note: All temperatures refer to topside of the package, measured on the package body surface.
Parameter Description
Rapid temperature changes
JESD22-A104D Condition G -40...125C
Vibration MIL-STD-883 Meth 2007 Cond A 20G 20-2000Hz 4x in each 3axis 4 min
Shock MIL-STD-202 Meth 213 Cond.C 100G 6ms 6 shocks in each direction
Solderability J_STD_002C Cond A, Through hole device/ Cond. B, SMD 255C (diving time50,5sec.) Dip+Look with 8h damp pre-treatment: solder wetting >95%
Solvent resistance MIL-STD-883 Meth 2015 Solv. 1,3,4
ESD HBM JESD22-A114-F Class 1C 10* 1000V
Moisture Sensit. Level 1 JESD22-A113-B
RoHS compliance 100% RoHS 6 compliant
Washable washable device
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 5 of 8
typical warm up@ MD-2031-DAE-1080-10M00
typical Phase Noise@ MD-2031-DAE-1080-10M00
typical temperature stability@ MD-2031-DAE-1080-10M00
typical residual error compare to fit curve @ MD-2031-DAE-1080-10M00
Typical Performance Data
600,0
610,0
620,0
630,0
640,0
650,0
660,0
670,0
680,0
690,0
700,0
150 250 350 450 550 650
Freq
uenc
y de
viat
ion
[ppb
]
Time [sec]-10
-8
-6
-4
-2
0
2
4
6
8
10
-40 -20 0 20 40 60 80
Fre
quen
cy d
evia
tion
[ppb
]
Temperature [°C]
-0,3
-0,2
-0,1
0
0,1
0,2
0,3
-40 -20 0 20 40 60 80
Res
idu
al e
rro
r c
om
par
e t
o f
itcu
rve
[pp
b]
Temperature [°C]
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 6 of 8
typical aging data@ MD-2031-DAE-1080-10M00
typical ADEV
@ MD-2031-DAE-1080-10M00
typical frequency vs. supply voltage@ MD-2031-DAE-1080-10M00
typical retrace@ MD-2031-DAE-1080-10M00
Typical Performance Data
-50
-40
-30
-20
-10
0
10
20
30
40
50
0 20 40 60 80 100 120 140
Time [d]
Fre
quen
cy d
evia
tion
[ppb
]
0,00
1,00
2,00
3,00
4,00
5,00
6,00
823,0
823,2
823,4
823,6
823,8
824,0
824,2
824,4
824,6
824,8
825,0
3000 3500 4000 4500 5000 5500
Sup
ply
volta
ge [
V]
Freq
uenc
y de
viat
ion
[ppb
]
Time [sec]
-1,0
-0,8
-0,6
-0,4
-0,2
0,0
0,2
0,4
0,6
0,8
1,0
1,2
1,4
1,6
1,8
2,0
0,00 500,00 1000,00 1500,00 2000,00 2500,00 3000,00 3500,00 4000,00
Freq
uenc
y de
viat
ion
[ppb
]
Time [min]
6 hours power on; 6 hours power off; 6 hours power on12 hours power off; 6 hours power on; 24 hours power off6 hors power on
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 7 of 8
typical case temperature vs. outside temperature@ MD-2031-DAE-1080-10M00
typical power consumption vs. operating temperature@ MD-2031-DAE-1080-10M00
@ MD-2031-DAE-1080-10M00
Typical Performance Data
-40
-20
0
20
40
60
80
100
-60 -40 -20 0 20 40 60 80 100
Tem
pera
ture
1
cm a
bove
osc
illato
r [°C
]
Temperature Test Chamber[°C]
0
100
200
300
400
500
600
700
800
-60 -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110 120C
urre
nt [m
A]
Ambient temperature [°C]
1
10
100
1000
1 10 100 1000
pow
er o
n tim
e be
fore
fine
adj
ustm
ent [
hour
s ]
storage time [days]
recommended power on time after x days of power off@ MD-2031-DAE-1080-10M00
Vectron International • 267 Lowell Road, Hudson Suite 102, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.comPage 8 of 8
Ordering Information
MD - 203 1 - D A E - 108 0 - 20M0000000
Product FamilyOX: OCXO
PackageSMD version: 203
Height1: 11,0 mm
Supply VoltageD: 5.0V
Stability Code108±10 ppb
Frequency
Frequency Control0: No Tuning
DisclaimerVectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.
Rev: 16.01.2015
For Additional Information, Please Contact USA:
Vectron International267 Lowell Road
Suite 102Hudson, NH 03051Tel: 1.888.328.7661Fax: 1.888.329.8328
Europe:Vectron InternationalLandstrasse, D-74924
Neckarbischofsheim, GermanyTel: +49 (0) 7268.801.100Fax: +49 (0) 7268.801.282
Asia:Vectron International
68 Yin Cheng Road(C), 22nd FloorOne LuJiaZui
Pudong, Shanghai 200120, ChinaTel: +86 21 6194 6886Fax: +86 21 6194 6699
RF Output CodeA: HCMOS
Temperature RangeJ: -20°C to +70°CE: -40°C to +85°C
Notes:1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies.2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C).3. Phase noise degrades with increasing output frequency.4. Subject to technical modification.5. Contact factory for availability.