lf25-30-105 compact unit heaters gas unit heaters / … · 2019-09-25 · lf25-030-105 compact unit...
TRANSCRIPT
LF25-030-105COMPACT UNIT HEATERS
Low Profile - Horizontal - 60 HzBulletin No. LF25-030-105 (08/2019)
Steady-State Efficiency - up to 83.8%Input - 30,000 to 105,000 Btuh
LF 25 - 045 A - 1 Unit Type
LF = Allied Unit Heater
Nominal Gas Heat Input 030 = 30,000 Btuh 045 = 45,000 Btuh 060 = 60,000 Btuh 075 = 75,000 Btuh 090 = 90,000 Btuh
105 = 105,000 BtuhHeat Exchanger Type A = Aluminized Steel
WARRANTY• Heat Exchanger - Aluminized steel - ten year limited• All other covered components:
• Five year limited - Residential installations• One year limited - Non-residential installations
APPROVALS• CSA International certified• Certified for natural or LPG/Propane gas.• Units are approved for vertical or horizontal venting
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . 5Features And Benefits . . . . . . . . . . . . . . . . . . 2Gas Heat Accessories . . . . . . . . . . . . . . . . . . 5Installation Clearances . . . . . . . . . . . . . . . . . . 6Maximum Vent Connector Lengths . . . . . . . . . . . 6Model Number Identification. . . . . . . . . . . . . . . 1Specifications . . . . . . . . . . . . . . . . . . . . . . . 5Vent Kits And Accessories . . . . . . . . . . . . . . . . 8
Series
LF25-30-105 COMPACT UNIT HEATERS
Minor Design Sequence 1 = 1st Generation 2 = 2nd Generation
R E S I D E N T I A L / C O M M E R C I A L P R O D U C T S P E C I F I C AT I O N S
G A S U N I T H E A T E R S / D U C T F U R N A C E S
MODEL NUMBER IDENTIFICATION
WARRANTY AND APPROVALSCONTENTS
LF25-030-105 Compact Unit Heaters / Page 2
APPLICATIONS• Horizontal unit heaters are low profile, compact in
design and easy to install• Steady State Efficiencies - Up to 83.8%• Ideal for economical heating systems in garages and
non-confined living spaces• Shipped completely assembled with controls factory
installed and wired• Hanging brackets are shipped loose for field installation• Test operated at the factory to ensure proper operation
and dependabilityNOTE - Installer must locate unit, make unit gas supply,
flue, electrical connections and mount thermostat to complete job.
CABINET• Constructed of pre-painted heavy gauge cold rolled steel• Hinged, reversible door for easy access• Adjustable louvers are furnished on cabinet for control
of air flow direction• Wiring junction box is conveniently located outside unit
cabinet for easy field wiring connections• Hanging brackets for suspending unit are furnished for
field installation• Unit may be rotated 180 degrees (top for bottom) for
ease of installation of gas, electrical and flue locations
HEATING SYSTEM
Tubular Aluminized Steel Heat Exchanger• Tubular heat exchanger is constructed of aluminized
steel for superior resistance to corrosion and oxidation• Curving design of heat exchanger allows complete
exposure of heating surfaces to supply air stream• Dimpled tubes with wrinkle bends allow for maximum heat
transfer
B
C
• Compact design reduces space requirements in unit cabinet. Heat exchanger has been laboratory life cycle tested
Inshot Burner Assembly• Aluminized steel inshot burners provide efficient trouble
free operation• Burner venturi mixes air and gas in correct proportion for
proper combustion• Burner assembly is removable from the unit as a single
component for ease of service
Gas Control Valve• 24 volt redundant combination gas control valve
combines manual shut off switch (On-Off), automatic electric valve (dual) and gas pressure regulation into a compact combination control
Combustion Air Inducer• Prepurges heat exchanger and safely vents combustion
products• Operates only during heating cycle• Blower motor has ball bearings and is thermally
protected
Pressure Switch• Pressure switch prevents unit operation in case of
blocked flue outlet
Limit Control(s)• Factory installed and accurately located• Limit control has fixed temperature setting and protects
heating system from abnormal operating conditions
Flame Rollout Switch• Automatic reset switch is factory installed on the top of
the burner box
D
E
OFF ON
LO
HI
C CHII I
1. Heavy Gauge Steel Cabinet2. Tubular Heat Exchanger3. Inshot Burners4. Combustion Air Inducer5. Combination Ignition Control6. Direct Drive fan
FEATURE HIGHLIGHTS
FEATURES AND BENEFITS
BC
DE F
G
LF25-030-105 Compact Unit Heaters / Page 3
HEATING SYSTEM (continued)
Optional Accessories
High Altitude Orifice Kits• Required on all units for proper unit operation at
altitudes from 5001 to 10,000 ft. (US) and 7501 to 10,000 ft. (Canada)
• Kits are available for natural gas and LPG/propane
High Altitude Pressure Switch Kit• Required for proper unit operation at various elevations
Natural Gas to LPG/Propane Conversion Kit• Required for field changeover from natural gas to LPG/
Propane
CONTROLS
Combination Direct Spark Ignition/Fan Timer Control Ignition Control• Electronic direct spark ignition control provides positive
and safe main burner ignition.• Spark is intermittent and occurs only when required.• Separate electronic flame sensor control assures safe
and reliable operation.• Should loss of flame occur, flame sensor controls will
initiate 5 attempts at re-ignition before locking out unit operation.
• Control board contains all necessary controls and relays to operate unit.
• Includes: Fan timer control - fan on 30 seconds (fixed), fan off 150 seconds (fixed), terminal strip for thermostat connections, diagnostic LED for troubleshooting.
• Direct plug-in wiring harness.
Transformer• 120V/24V transformer furnished as standard
F
VENTING• Units may be vented horizontally or vertically
• Residential Vertical Venting - Units are approved for installation with single wall vent pipe or Type B double wall vent pipe
• Residential Horizontal Venting - Units are approved for residential installation only with Allied-approved stainless steel vent kits
• Commercial Vertical Venting - Units are approved for installation with single wall vent pipe only
• Commercial Horizontal Venting - Units are approved for single-wall vent pipe or optional Allied-approved, UL listed, Cat III stainless steel vent kits
Optional Accessories
Horizontal Vent Kits• UL listed, Cat III stainless steel vent kits are required for
horizontal venting.• Available for upward or downward slope• Vent kits snap together• Kits include unit transition, vent termination and wall
thimble• Upward slope vent kits have a drain connection• Provisions for hanging must be field supplied• Optional 45° or 90° elbow available for ease of vent
connection• Straight pipe sections in various lengths are availableNOTE - See Horizontal Vent Kits / Elbow table for Allied-
approved Horizontal Vent Kits and accessories on Page 6.
NOTE - See drawings for additional information.NOTE - See installation instructions for detailed venting
requirements.
DIRECT DRIVE FAN• Efficient and quiet operating direct drive propeller type fan• Permanently lubricated fan motor
G
FEATURES AND BENEFITS
THIS PAGE INTENTIONALLY LEFT BLANK
LF25-030-105 Compact Unit Heaters / Page 4
LF25-030-105 Compact Unit Heaters / Page 5
SPECIFICATIONSGas Heating Performance
Model No. LF25-030A LF25-045A LF25-060A LF25-075A LF25-090A LF25-105AHeating Capacity Input Btuh 30,000 45,000 60,000 75,000 90,000 105,000
Heating Capacity Output Btuh - Natural 25,020 37,665 50,220 62,550 75,420 87,675
Steady State Efficiency - Natural 83.4% 83.7% 83.7% 83.4% 83.8% 83.5%
Temperature rise - °F 37 52 47 65 43 59
Connections in.
Flue size (round) 4 4 4 4 4 4
Gas Piping Size - in. 1/2 1/2 1/2 1/2 1/2 1/2
Fan Data Number of fans 1 1 1 1 1 1
Fan Diameter - in. 10 10 14 14 16 16
Number of blades 4 4 4 4 4 4
Motor Output - hp 1/25 1/25 1/15 1/15 1/10 1/10
rpm 1550 1550 1075 1075 1075 1075
Air Volume - cfm 625 665 1000 1200 1600 1500
Air throw at 8 ft. mounting height - ft. 27 29 34 41 46 43
Weight Data Net Weight - lbs. (kg) 55 (25) 60 (27) 85 (39) 90 (41) 115 (52) 120 (54)
Shipping Weight - lbs. (kg) 60 (27) 65 (29) 90 (41) 95 (43) 120 (54) 125 (57)
ELECTRICAL DATAVoltage 115 volts - 60 hertz - 1 phase
Fan motor full load amps 2.0 2.0 2.0 2.0 2.0 3.0
Maximum overcurrent protection 15 15 15 15 15 15
GAS HEAT ACCESSORIESUS
Natural Gas to LPG/Propane Kit
LPG/Propane High Altitude Orifice Kit
Natural Gas High Altitude Orifice Kit
0 - 5000 ft. 5001- 8000 ft. 8001 - 10,000 ft. 5001 - 7000 ft. 7001 - 10,000 ft.18L11 19A10 19A11 19A17 19A18
Canada
Natural Gas to LPG/Propane Kit
LPG/Propane High Altitude Orifice Kit
Natural Gas High Altitude Orifice Kit
0 - 7500 ft. 7501- 9500 ft. 7501- 9500 ft.
18L11 19A12 19A17
GAS HEAT ACCESSORIES HIGH ALTITUDE PRESSURE SWITCH KITSAltitude - ft. 0-3000 3000-5000 5001-6000 6001-7000 7001-9000 9001-10,000LF25-030A Factory Factory Factory 18L35 18L35 18L35LF25-045A Factory Factory Factory 18L35 18L35 18L35LF25-060A Factory Factory 18L19 18L19 18L19 18L50LF25-075A Factory 18L20 18L20 18L35 18L35 18L35Altitude - ft. 0-2000 2001-4000 4001-6000 6001-7000 7001-9000 9001-10,000LF25-090A Factory 18L20 18L19 18L35 18L35 18L35LF25-105A Factory Factory 18L47 18L47 18L35 18L35
LF25-030-105 Compact Unit Heaters / Page 6
INSTALLATION CLEARANCESin. mm
Top 1 25Side opposite control box/access panel 1 25Control Box/Access Panel Side 24 610Back 18 457Bottom 1 1¹ Flue 6 152See Installation Instructions for further installation considerations.1 Single-Wall vent clearance. Type B Double-Wall vent clearance is in accordance
with the manufacturer’s listing.
MAXIMUM VENT CONNECTOR LENGTHSNo. of
ElbowsMaximum Length (feet)
of Straight Vent Pipe1 252 203 154 105 5
NOTES - Minimum horizontal vent length is 5 ft. Horizontal venting requires the use of a Allied-approved Cat III Horizontal Vent Kit and Vent Pipe. Horizontal venting must terminate in a tee. Maximum total length of vent pipe must not exceed 30 ft. One elbow is equivalent to 5 ft. of vent pipe. Residential Vertical Venting - Units are approved for installation with single wall vent pipe or Type B double wall vent pipe. Residential Horizontal Venting - Units are approved for residential
installation only with Allied-approved stainless steel vent kits. Commercial Vertical Venting - Units are approved for installation with single wall vent pipe only. Commercial Horizontal Venting - Units are approved for single-wall
vent pipe or optional Allied-approved, UL listed, Cat III stainless steel vent kits. Minimum clearance to combustible material is 6 in. with single wall vent pipe.
HORIZONTAL VENT KITS AND ELBOWREQUIRED FOR RESIDENTIAL HORIZONTAL VENTING APPLICATIONS
Unit Heater
Model No.
Vent Diameter
(in.)
Upslope Vent Kit
Catalog No.
Downslope Vent Kit
Catalog No. 45° Elbow Catalog
No. 90° Elbow Catalog No.
1 Minimum Vent
Length (ft.)
LF25-030A LF25-045A LF25-060A LF25-075A LF25-090A LF25-105A
4 C5VENT4KU 75W63 C5VENT4KD 75W67C5VENT4E45
(Optional) 87W80C5VENT4E (Optional) 75W71 5
1 Length does not include temrination (or elbow if used).
STRAIGHT VENT PIPE - FOR HORIZONTAL VENTINGUnit Heater Model No. Vent Diameter (in.) Length (in.) Catalog No.LF25-030A LF25-045A LF25-060A LF25-075A LF25-090A LF25-105A
C5VENT4P6 4 6 75W77C5VENT4P12 4 12 75W78C5VENT4P36 4 36 75W79
LF25-030-105 Compact Unit Heaters / Page 7
2-3/4(70)
8-3/4(222)
10-1/2(267)
4-1/4(108)
1/2[13]
1(25)
21(533)
1(25)
A
3-5/8(92)
C
29(737)
B 21(533)
BACK VIEW
FLUEOUTLET
GASINLET
DIRECTDRIVE FAN
ELECTRICALINLET
BRACKETS (2)HANGING
TOP VIEW
HEAT EXCHANGER
AIRFLOW
MOUNTING SLOTS (Typical)5/16 x 3 Inches (8 x 76 mm)
HANGINGBRACKETS (2)
SERVICEACCESSPANEL SIDE VIEW
ADJUSTABLELOUVERS
1(25)
Model No.
A B Cin. mm in. mm in. mm
LF25-030A LF25-045A 12-3/8 314 6-1/2 165 3-7/8 98
LF25-060A LF25-075A 17-1/2 445 6-1/4 159 6-1/8 156
LF25-090A LF25-105A 23 584 7-7/8 200 9-1/8 232
DIMENSIONS
LF25-030-105 Compact Unit Heaters / Page 8
HORIZONTAL VENT KITS (UPSLOPE)
90° ELBOW (Typical)
STRAIGHT PIPE (Typical)
HORIZONTAL VENT KITS (DOWNSLOPE)
45° ELBOW (Typical)
VENT KITS AND ACCESSORIES
NOTE - Due to Allied Commercial ongoing commitment to quality, Specifications, Ratings and Dimensions subject to change without notice and without incurring liability. Improper installation, adjustment, alteration, service or maintenance can cause property damage or personal injury. Installation and service must be performed by a qualified installer and servicing agency.
©2019 Allied Air Enterprises LLC, a Lennox International Inc. Company
Visit us at www.allied-commercial.com For the latest technical information, visit us at www.allied-commercial.com Contact us at 1-800-448-5872
REVISIONS
REVISIONS
Sections Description of Change
Specifications Outputs and efficiencies updated.