led lighted push button with keyfinder light - heath- ?· led lighted push button with keyfinder...

Download LED Lighted Push Button with Keyfinder Light - heath- ?· LED Lighted Push Button with Keyfinder Light…

Post on 29-Aug-2018

214 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • LED LightedPush Button with Keyfinder Light

    2007 HeathCo LLC 598-1281-02

    Thepushbuttonissetfromthefactoryfor use with mechanical chimes, butcanbeusedwitheithermechanicalorelectronicchimes.

    Followtheseinstructionstoinstallyourpushbuttonandsetittoworkwithyourparticularchime.

    IMPORTANT: Push button must beinstalled with keyfinder light facingdownward.

    Keyfinder Lens

    PushButton

  • 598-181-0

    1.Usingasmallscrewdriver,pushintabonbottomofpushbutton to removeback(seeFigure1).

    2.Insertwiresthroughholeincenterofpushbuttonback.Attachbacktowallwithscrewsprovided(seeFigure2).

    InstallationIMPORTANT: DO NOT install addi-tionaldiode(s)topushbutton.Additionaldiode(s)willcausechimetomalfunction.

    Figure 2 - Attach Back to Wall

    Figure 1 - Remove Push Button Back

  • 598-181-0

    3.Attachthetwowiresfromyourchimeandtransformertothescrewterminalsonthebackofyourpushbutton(seeFigure 3). Press push button to testfunction.

    4.Ifyourchimefunctionscorrectlyandplaystheentiretune,skiptostep9.Ifyourchimedoesnotfunctioncorrectly,proceedwithstep5.

    Figure 3 - Attach Chime Wires toPush Button (Back of Push Button Shown)

  • 598-181-0

    CAUTION: Do NOT connect pushbutton to mechanical chime if pushbutton jumper is set for electronicchime use. Doing so may result inpermanentdamagetoyourchime.

    FR

    ON

    T TR

    AN

    S

    RE

    AR

    DO

    NO

    T O

    IL

    Tone Bar

    Figure 4 - Inside Typical Mechanical Chime

    Plunger

    Determine Chime Type

    5.Locate your chime and remove thecover.Ifyouseetonebarsandplungersyou have a mechanical chime (seeFigure4).Ifnot,youhaveanelectronicchime.

    6.Ifyouhaveamechanicalchime,gototheTroubleshootingsection,page7.Ifyouhaveanelectronicchimeproceedtostep7onpage5.

  • 5598-181-0

    Figure 5 - Determining Correct Jumper Position (Back of Push Button)

    Jumper On Two Top Pins for Electronic Chime

    7.Ifyouhaveanelectronicchime,movethejumperonthebackofyourpushbuttonfromthetwobottompinstothetwotoppins(seeFigure5).Presspushbuttontotestagain.

    8.If your chime still does not operatecorrectly,seeTroubleshooting,page7.

    Jumper On Two Bottom Pins for Mechanical Chime

  • 598-181-0

    TroubleshootingIfbellorchimedoesnotoperate: For Electronic Chimes: If tune does

    not play completely, reverse wiresconnectedtothepushbutton.

    Disconnectwiresfrombuttonandtouchtogether. If bell or chime operates,replacewithnewbutton.

    Checktransformer,bell,orchime.

    9.Onceyourpushbuttonandchimearewiredandfunctioningcorrectly,placetopofpushbuttonontobackandsnapbottomofpushbuttonintoplace(seeFigure6).Note:Thepushbuttonmustbe mounted with the keyfinder lensfacingdownward.

    Figure 6 - Attach Push Button onto Back

  • 598-181-0

    HeathCoLLCreservestherighttodiscontinueandtochangespecificationsatanytimewith-outnoticewithoutincurringanyobligationtoincorporate new features in previously soldproducts.

    Lifetime Finish Warranty(Selected Models Only)

    FullLifetimeFinish(plateonly)warrantytotheoriginaluser(User)ofLifetimeFinish (Product) against premisesuponwhich theProductwasoriginallyinstalled. This warranty DOES NOTCOVER:(I)scratchesorabrasions,(II)abusedormisusedProducts,or(III)Prod-uctsusedincommercialapplications.

    Technical ServicePlease call 1-800-858-8501 (English speaking only) for assistance before

    returning product to store.

    Ifyouexperienceaproblem,followthisguide.You may also want to visit ourWebsiteat:www.hzsupport.com.Iftheproblempersists,call*forassistanceat1-800-858-8501,7:30AMto4:30PMCST(M-F).Youmayalsowrite*to:

    HeathCoLLCP.O.Box90004,BowlingGreen,KY42102-9004ATTN:TechnicalService

    *IfcontactingTechnicalService,pleasehavethefollowinginformationavailable:ModelNumber, Date ofPurchase, andPlaceofPurchase.

    No Service Parts Available for this Product

  • 8 598-181-0

    ONE YEAR LIMITED WARRANTYThis is a Limited Warranty which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.

    For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.

    Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges.

    This warranty covers only HeathCo LLC as-sembled products and is not extended to other equipment and components that a customer uses in conjunction with our products.

    THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MER-CHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

    REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDI-RECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for all warranty requests.

  • 9598-181-0

    Pulsador coniluminacin LED y

    con luz busca-llaves

    Elpulsadorvienecalibradodefbricaparausarseconcampanasmecnicas,peropuedeusarsetantoconcampanasmecnicascomoconelectrnicas.

    Sigalasinstruccionesparainstalarsupulsadorycalbreloparaquefuncioneconsucampanaenparticular.

    IMPORTANTE: El pulsador debe serinstaladoconlaluzbusca-llavesmirandohaciaabajo.

    2007 HeathCo LLC 598-1281-02 S

    Lente del busca-llaves

    Pulsador

  • 10 598-181-0

    IMPORTANTE:NOinstalediodo(s)adicional(es) en el pulsador. Losdiodo(s) adicionales harn que lacampanafuncionemal.

    1.Utilizandoundestornilladorpequeo,presionelalengetaenlaparteinferiordelbotnparaquitarlaparteposterior(vealaFigura1).

    2.Inserteloscablesatravsdelagujeroenelcentrodelaplacaposteriordelbotn.Fijelaparteposterioralaparedconlostornillosqueseproporcionan(vealaFigura2).

    Instalacin

    Figura 2 - Fije la parte de atrs a la pared

    Figura 1 - Quite la parte de atrs del pulsador

  • 11598-181-0

    3.Conectelosdosconductoresdesucampanay transformador a los terminales detornillodelaparteposteriordesupulsador(vealaFigura3).Presioneelpulsadorparaprobarelfuncionamiento.

    4.Sisucampanafuncionacorrectamentey reproduce todo el tono, vaya alpaso 9. Si su campana no funcionacorrectamente,procedaconelpaso5.

    Figura 3 - Conecte los conductores de la campana al pulsador (vista posterior del

    pulsador)

  • 1 598-181-0

    PRECAUCIN:NOconecteelpulsa-doralacampanamecnicasielpuentedelpulsadorestcalibradoparalacam-panaelectrnica.Si lo conectapuededaarpermanentementealacampana.

    FR

    ON

    T TR

    AN

    S

    RE

    AR

    DO

    NO

    T O

    IL

    Barra de tonos

    Figura 2 - Interior de una campanamecnica tpica

    mbolo

    Determine el tipo de campana

    5.Vaya a su campana y retire la tapa.Sivebarrasymbolosparaproducirtonos lo que tiene es una campanamecnica(vea laFigura2).Sinoesas,tieneunacampanaelectrnica.

    6.Sitieneunacampanamecnica,vayaa la seccin Anlisis de averas enla pgina 15. Si tiene una campanaelectrnicaprocedaconelpaso7delapgina13.

  • 1598-181-0

    Figura 5 - Determinacin correcta de la posicin del puente (parte posterior del

    pulsador)

    Puente sobre dos clavijas superiores para campana electrnica

    7.Si tiene una campana electrnica,muevaelpuentequeestenlapartedeatrsdelpulsadordelasdosclavijasinferioresalasdosclavijassuperiores(vealaFigura5).Presioneelpulsadorparaprobardenuevo.

    8.S i su campana an no operacorrectamente,veaAnlisis de averasenlapgina15.

    Puente sobre dos clavijas inferiores para campana mecnica

  • 1 598-181-0

    Figura 6 - Fije el pulsador sobre la parte de atrs

    9.Unavezqueelpulsadorylacampanaestn conectados y funcionandocorrectamente,pongalapartesuperiordelpulsadorsobrelapartedeatrsyasienteapresinensulugarlaparteinferiordelpulsador(vealaFigura6).Nota:Elpulsadordebesermontadoconlalentebusca-llavesmirandohaciaabajo.

    Anlisis de averasSieltimbreocampananoopera: En campanas electrnicas: Si no

    reproduce todo el tono, invierta losconductoresconectadosalpulsador.

    Desconecte los conductores delpulsadorynalosentresi.Sieltimbreolacampanafuncionan,cambieporunpulsadornuevo.

    Reviseeltransformador,eltimbreolacampana.

  • 15598-181-0

    HeathCoLLCsereservaelderechodedescon-tinuarproductosydecambiarespecificacionesacualquiermomentosinincurrirenningunaobliga-cindetenerqueincorporarnuevascaractersticasenlosproductosvendidosconanterioridad.

    La Garanta del Acabado Perpetua(Modelos seleccionados solamente)

    ElAcabadodeVidaLieno(slochapa)lagarantaalusuariooriginal(elUsuario)deAcabado Perpetua (el Producto)contrapremisasenqueelProductofueinstalado originalemente. Esta garantaNOCUBRE:(I)araazosoabrasiones,(II)abusoemplemallosProductos,o(III)losProductosusaronenlasaplica-cionescomericiales.

    Servicio TcnicoFavor de llamar al 1-800-858-8501 (slo para hablar en ingls) para pedir ayuda antes de devolver el

    producto a la tienda.S