End connectionAK ............. Tapered NPT (ASME B1.20.1)AW ............ Socket Weld (ASME B16.11)BW ............ Buttweld (ASME B16.25)AK/AW ...... Threaded x Socket WeldShell materialSC .............. Carbon SteelU ............... Stainless SteelValve TypeT ................ Floating Ball3T .............. 3-PCBore designK ................Double ReducedH ............... Single ReducedF ................ FullMounting padZ ................ Integral (ISO-5211 on 3-pc)Trim (Ball and stem)M .............. 316SSOptionsFS .............. Fire Tested per API 607 OperatorNone ........ Locking LeverO ............... Locking Oval Special FeaturesW .............. Seal WeldedEnd connectionAK ............. Tapered NPT (ASME B1.20.1)AW ............ Socket Weld (ASME B16.11)Valve operation measureNone ... Lever handleG......... Worm gearE.......... Electric actuatorB.......... KITZ Type B double actionpneumatic actuatorBS ........ KITZ Type BSspring returnpneumatic actuatorFA....... KITZ Type FA double actionpneumatic actuatorFAS ...... KITZ Type FAS spring returnpneumatic actuatorASME pressure class150, 300, 600 or 1500Shell materialSC ........ Carbon or low alloy steelU......... Stainless or high alloy steel Shell materialAn additional symbol is sufxed here, if other than WCB or CF8 is employed for shell material, such as:M........ CF8MV......... CF3O......... CF3MCB....... CF8CCN ....... CN7MSymbol for ball valvesValve designDZ ........ Full Bore, split body with ISO / CAPI actuator mounting padB .......... Full Bore, split body with KITZ actuator mounting padA......... Single Reduced Bore, uni-body with ISO / CAPI actuator mouting padTrim material for carbon steelvalvesNo symbol for 304 s/s trim."M" for 316 s/s trim."FS" For Flexible graphite packing and gasket for super-fre-safe provision in accordance with API607No symbol for PTFE packing gasket."(C)" For CAPI Confguration of Single Reduced Bore002KITZ steel ball valves, foating ball designKITZ Steel Ball ValvesFloating Ball DesignDesign and Inspection Standards KITZ Product CodingProduct RangeDesign FeaturesKITZ HYPATITE PTFE Ball SeatsLow Emission Design FeaturesPressure-Temperature RatingsClass 150 / 300 Cast Steel Ball Valves Class 600 / 1500 Carbon Steel Ball ValvesClass 150 / 300 Cast Stainless Steel Ball ValvesClass 600 / 1500 Cast Stainless Steel Ball ValvesClass 150 / 300 Cryogenic Ball Valves2000 / 1500 WOG Carbon Steel Ball ValvesType 600 Carbon Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball Valves2000 / 1500 WOG Stainless Steel Ball ValvesType 600 Stainless Steel Ball ValvesType 800 Stainless Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesDimensions of Actuator Mounting PadsConstruction and MaterialsTechnical InformationTechnical Features of KITZ HYPATITE PTFE Ball SeatsFire Test StandardsGeneral PrecautionsFlow CharacteristicsSteel Pipe Flanges223710111316242632354151526474757688100112124135139147149151152153ContentsThe products introduced in this catalog are all covered by ISO 9001 and 9002 certifcation awarded KITZ Corporation, KITZ Corporation of Europe,S.A. and KITZ Corporation of Taiwan.Design and Inspection Standards of KITZ Flanged Ball ValvesProduct Coding for KITZ Flanged Ball Valves Pressure-temperature ratingsGeneral valve designShell wall thicknessFace-to-face dimensionsEnd fange dimensions and fange gasket facingPressure testFire testBodyResilient sealing partsAmerican StandardsAPI 608API 608ASME B16.34API 598 or API 6D*1API 607 or API 6FAISO StandardsISO 17292ISO 17292ISO 17292ISO 17292ISO 10497ASME B16.34ASME B16.10ASME B16.5*1 OptionItemDesign and Inspection Standards of KITZ Threaded Ball Valves Pressure-temperature ratingsShell wall thicknessFace-to-face dimensionsEnd connectionsPressure testFire testBodyResilient sealing partsThreadedSocket WeldButtweldAmerican StandardsKITZ StandardKITZ StandardASME B16.34*1KITZ StandardASME B1.20.1ASME B16.11ASME B16.25API 598API 607*1 Except AKSCTKM (50), AKUTKM (52) and AKUTHM (53) which are KITZ standardItemBL ........ LCBCL ........ LCCExample G-150150USCTTATDZMM - FSProduct Coding for KITZ Threaded Ball ValvesW AKAKAWUSCSCTT3THKFZZZMMM- FS- FSExampleO1L ........ LC12L ........ LC23L ........ LC3(C)End connectionAK ............. Tapered NPT (ASME B1.20.1)AW ............ Socket Weld (ASME B16.11)BW ............ Buttweld (ASME B16.25)AK/AW ...... Threaded x Socket WeldShell materialSC .............. Carbon SteelU ............... Stainless SteelValve TypeT ................ Floating Ball3T .............. 3-PCBore designK ................Double ReducedH ............... Single ReducedF ................ FullMounting padZ ................ Integral (ISO-5211 on 3-pc)Trim (Ball and stem)M .............. 316SSOptionsFS .............. Fire Tested per API 607 OperatorNone ........ Locking LeverO ............... Locking Oval Special FeaturesW .............. Seal WeldedEnd connectionAK ............. Tapered NPT (ASME B1.20.1)AW ............ Socket Weld (ASME B16.11)Valve operation measureNone ... Lever handleG......... Worm gearE.......... Electric actuatorB.......... KITZ Type B double actionpneumatic actuatorBS ........ KITZ Type BSspring returnpneumatic actuatorFA....... KITZ Type FA double actionpneumatic actuatorFAS ...... KITZ Type FAS spring returnpneumatic actuatorASME pressure class150, 300, 600 or 1500Shell materialSC ........ Carbon or low alloy steelU......... Stainless or high alloy steel Shell materialAn additional symbol is sufxed here, if other than WCB or CF8 is employed for shell material, such as:M........ CF8MV......... CF3O......... CF3MCB....... CF8CCN ....... CN7MSymbol for ball valvesValve designDZ ........ Full Bore, split body with ISO / CAPI actuator mounting padB .......... Full Bore, split body with KITZ actuator mounting padA......... Single Reduced Bore, uni-body with ISO / CAPI actuator mouting padTrim material for carbon steelvalvesNo symbol for 304 s/s trim."M" for 316 s/s trim."FS" For Flexible graphite packing and gasket for super-fre-safe provision in accordance with API607No symbol for PTFE packing gasket."(C)" For CAPI Confguration of Single Reduced Bore002KITZ steel ball valves, foating ball designKITZ Steel Ball ValvesFloating Ball DesignDesign and Inspection Standards KITZ Product CodingProduct RangeDesign FeaturesKITZ HYPATITE PTFE Ball SeatsLow Emission Design FeaturesPressure-Temperature RatingsClass 150 / 300 Cast Steel Ball Valves Class 600 / 1500 Carbon Steel Ball ValvesClass 150 / 300 Cast Stainless Steel Ball ValvesClass 600 / 1500 Cast Stainless Steel Ball ValvesClass 150 / 300 Cryogenic Ball Valves2000 / 1500 WOG Carbon Steel Ball ValvesType 600 Carbon Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball Valves2000 / 1500 WOG Stainless Steel Ball ValvesType 600 Stainless Steel Ball ValvesType 800 Stainless Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesType 1500 / 1000 Carbon Steel Ball ValvesType 1500 / 1000 Stainless Steel Ball ValvesDimensions of Actuator Mounting PadsConstruction and MaterialsTechnical InformationTechnical Features of KITZ HYPATITE PTFE Ball SeatsFire Test StandardsGeneral PrecautionsFlow CharacteristicsSteel Pipe Flanges223710111316242632354151526474757688100112124135139147149151152153ContentsThe products introduced in this catalog are all covered by ISO 9001 and 9002 certifcation awarded KITZ Corporation, KITZ Corporation of Europe,S.A. and KITZ Corporation of Taiwan.Design and Inspection Standards of KITZ Flanged Ball ValvesProduct Coding for KITZ Flanged Ball Valves Pressure-temperature ratingsGeneral valve designShell wall thicknessFace-to-face dimensionsEnd fange dimensions and fange gasket facingPressure testFire testBodyResilient sealing partsAmerican StandardsAPI 608API 608ASME B16.34API 598 or API 6D*1API 607 or API 6FAISO StandardsISO 17292ISO 17292ISO 17292ISO 17292ISO 10497ASME B16.34ASME B16.10ASME B16.5*1 OptionItemDesign and Inspection Standards of KITZ Threaded Ball Valves Pressure-temperature ratingsShell wall thicknessFace-to-face dimensionsEnd connectionsPressure testFire testBodyResilient sealing partsThreadedSocket WeldButtweldAmerican StandardsKITZ StandardKITZ StandardASME B16.34*1KITZ StandardASME B1.20.1ASME B16.11ASME B16.25API 598API 607*1 Except AKSCTKM (50), AKUTKM (52) and AKUTHM (53) which are KITZ standardItemBL ........ LCBCL ........ LCCExample G-150150USCTTATDZMM - FSProduct Coding for KITZ Threaded Ball ValvesW AKAKAWUSCSCTT3THKFZZZMMM- FS- FSExampleO1L ........ LC12L ........ LC23L ........ LC3(C)002product rangeStainless Steel1616171718181919202021212222232324242525262727282829293030313132323333343536373839Product Rangeproduct rangeMaterial Figure Code No. WOG Type Bore Ends Body Stem Ball Gasket Ball Seat Page 1/4" 11/4" 11/2" 2" 1" 21/2" 3" 4" 5" 6" 8"3/8"1/2"3/4"Material150SCTDZM (C)150SCTDZM-FS (C)G-150SCTDZM (C)G-150SCTDZM-FS (C)150SCTAM (C)150SCTAM-FS (C)150SCTAM (C)150SCTAM-FS (C)300SCTDZM (C)300SCTDZM-FS (C)300SCTAM (C)300SCTAM-FS (C)300SCTAM (C)300SCTAM-FS (C)600SCTBM600SCTBM-FS1500SCTBM1500SCTBM-FS150UTDZM (C)150UTDZM-FS (C)G-150UTDZM (C)150UTAM (C)150UTAM-FS (C)150UTAM (C)150UTAM-FS (C)300UTDZM (C)300UTDZM-FS (C)300UTAM (C)300UTAM-FS (C)300UTAM (C)300UTAM-FS (C)600UTBM600UTBM-FS1500UTBM1500UTBM-FS150UTALMG-150UTALM300UTALMG-300UTALMFigure Code No.Anti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceClass15030060015001503006001500150300TypeLow EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)CryogenicBoreFullSingleReducedFullFullFullFullFullSingleReducedSingleReducedSingleReducedSingleReducedEndsFlanged...ASME B16.5Flanged...ASME B16.5BodyA216 Gr.WCBA105A216 Gr. WCBA351 Gr.CF8MStemA276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A479/A479M Type 316A276 Type 316A276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A564 Type 630BallA351 Gr. CF8M/A276 Type 316A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA351 Gr.CF8M/A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A351 Gr. CF8M/A276 Type 316A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA351 Gr. CF8M/A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316/A351 Gr. CF8MA276 Type 316/A479 Type 316/A351 Gr. CF8MA276 Type 316GasketPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEFlexible GraphiteFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteFlexible GraphiteSpiral WoundFlexible GraphiteSpiral WoundFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteBall Seat PageHYPATITE PTFE*G/F MoS2 PTFEMoS2 NylonHYPATITE PTFEG/F MoS2 PTFEMoS2 NylonHYPATITE PTFE11/4" 11/2"

2"

1" 21/2"

3"

4"

5"

6"

8"

10"3/8"

1/2"

3/4"AKSCTKZM-FSAKSCTKZM-FSOAKSCTHZMAKSCTHZM-OAKSCTHZM-FSAKSCTHZM-FSOAKSCTHWZMAKSCTHWZM-OAKSCTHWZM-FSAKSCTHWZM-FSOAKSCTKMFire Safe per API607Anti-Static DeviceFire SafeAnti-Static DeviceFire Safe per API6072000...1/4"-1"1500...11/4-2"600Actuator Mounting PadTwo PieceActuator Mounting PadActuator Mounting PadSeal Welded Two PieceActuator Mounting Pad119119-LOH217217-LOH219219-LOH237237-LOH239239-LOH50DoubleReducedSingleReducedScrewed...ASME B 1.20.1A216 Gr.WCB Carbon Steel A276 Type 316 A276 Type 316A276 Type 316PTFEPTFEFlexible GraphiteFlexible Graphite HYPATITE PTFE

4041424344454647484950Flexible GraphiteSpiral WoundFlexible GraphiteSpiral WoundCarbon Steel003product rangeStainless Steel1616171718181919202021212222232324242525262727282829293030313132323333343536373839Product Rangeproduct rangeMaterial Figure Code No. WOG Type Bore Ends Body Stem Ball Gasket Ball Seat Page 1/4" 11/4" 11/2" 2" 1" 21/2" 3" 4" 5" 6" 8"3/8"1/2"3/4"Material150SCTDZM (C)150SCTDZM-FS (C)G-150SCTDZM (C)G-150SCTDZM-FS (C)150SCTAM (C)150SCTAM-FS (C)150SCTAM (C)150SCTAM-FS (C)300SCTDZM (C)300SCTDZM-FS (C)300SCTAM (C)300SCTAM-FS (C)300SCTAM (C)300SCTAM-FS (C)600SCTBM600SCTBM-FS1500SCTBM1500SCTBM-FS150UTDZM (C)150UTDZM-FS (C)G-150UTDZM (C)150UTAM (C)150UTAM-FS (C)150UTAM (C)150UTAM-FS (C)300UTDZM (C)300UTDZM-FS (C)300UTAM (C)300UTAM-FS (C)300UTAM (C)300UTAM-FS (C)600UTBM600UTBM-FS1500UTBM1500UTBM-FS150UTALMG-150UTALM300UTALMG-300UTALMFigure Code No.Anti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceClass15030060015001503006001500150300TypeLow EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)Low EmissionLevel- (Max.20ppm.)Low EmissionLevel- (Max.100ppm.)CryogenicBoreFullSingleReducedFullFullFullFullFullSingleReducedSingleReducedSingleReducedSingleReducedEndsFlanged...ASME B16.5Flanged...ASME B16.5BodyA216 Gr.WCBA105A216 Gr. WCBA351 Gr.CF8MStemA276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A479/A479M Type 316A276 Type 316A276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A276 Type 316A479/A479M Type 316A276 Type 316A564 Type 630BallA351 Gr. CF8M/A276 Type 316A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA351 Gr.CF8M/A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A351 Gr. CF8M/A276 Type 316A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA351 Gr. CF8M/A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316/A351 Gr. CF8MA276 Type 316/A479 Type 316/A351 Gr. CF8MA276 Type 316GasketPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEPTFEFlexible GraphiteFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteFlexible GraphiteSpiral WoundFlexible GraphiteSpiral WoundFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteBall Seat PageHYPATITE PTFE*G/F MoS2 PTFEMoS2 NylonHYPATITE PTFEG/F MoS2 PTFEMoS2 NylonHYPATITE PTFE11/4" 11/2"

2"

1" 21/2"

3"

4"

5"

6"

8"

10"3/8"

1/2"

3/4"AKSCTKZM-FSAKSCTKZM-FSOAKSCTHZMAKSCTHZM-OAKSCTHZM-FSAKSCTHZM-FSOAKSCTHWZMAKSCTHWZM-OAKSCTHWZM-FSAKSCTHWZM-FSOAKSCTKMFire Safe per API607Anti-Static DeviceFire SafeAnti-Static DeviceFire Safe per API6072000...1/4"-1"1500...11/4-2"600Actuator Mounting PadTwo PieceActuator Mounting PadActuator Mounting PadSeal Welded Two PieceActuator Mounting Pad119119-LOH217217-LOH219219-LOH237237-LOH239239-LOH50DoubleReducedSingleReducedScrewed...ASME B 1.20.1A216 Gr.WCB Carbon Steel A276 Type 316 A276 Type 316A276 Type 316PTFEPTFEFlexible GraphiteFlexible Graphite HYPATITE PTFE

4041424344454647484950Flexible GraphiteSpiral WoundFlexible GraphiteSpiral WoundCarbon Steel004A216 Gr.WCBMaterial Figure Code No. WOG Type Bore Ends Body Stem Ball Gasket Ball Seat Page

1/4"

11/4" 11/2" 2" 1" 21/2" 3" 4" 5" 6" 8"3/8"1/2"3/4"51525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110product range product rangeAKSC3TFZM-OAKSC3TFZMAKSC3THZM-OAKSC3THZMAKSC3TFZM-FSOAKSC3TFZM-FSAKSC3THZM-FSOAKSC3THZM-FSAKUTKZM-FSAKUTKZM-FSOAKUTHZMAKUTHZM-OAKUTHZM-FSAKUTHZM-FSOAKUTHWZMAKUTHWZM-OAKUTHWZM-FSAKUTHWZM-FSOAKUTKMAKUTHMAKU3TFZM-OAKU3TFZMAKU3TFZM-FSOAKU3TFZM-FSAKU3THZM-OAKU3THZMAKU3THZM-FSOAKU3THZM-FSBWSC3TFZM-OBWSC3TFZMBWSC3THZM-OBWSC3THZMBWSC3TFZM-FSOBWSC3TFZM-FSBWSC3THZM-FSOBWSC3THZM-FSBWU3TFZM-OBWU3TFZMBWU3THZMBWU3TFZM-FSOBWU3TFZM-FSBWU3THZM-FSOBWU3THZM-FSAnti-Static DeviceFire SafeAnti-Static DeviceFire Safe per API607Anti-Static DeviceFire Safe per API607Fire Safe per API607Anti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static Device1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"2000...1/4"-1"1500...11/4-2"600800Three Piece ISO 5211 Actuator Mounting PadActuator Mounting PadTwo Piece Actuator Mounting PadSeal Weld Two PieceActuator Mounting PadThree Piece ISO 5211 Actuator Mounting PadThree Piece ISO 5211 Actuator Mounting PadThree Piece ISO 5211 Actuator Mounting Pad317F-LOH317F317-LOH317319F-LOH319F319-LOH319129-LOH129-LOH227227-LOH229229-LOH247247-LOH249249-LOH5253327F-LOH327F329F-LOH329F327-LOH327329-LOH329317FB-LOH317FB317B-LOH317B319FB-LOH319FB319B-LOH319B327FB-LOH327FB327B-LOH327B329FB-LOH329FB329B-LOH329BFullSingleReducedSingleReducedFullFullSingleReducedDoubleReducedDoubleReducedSingleReducedFullFullSingleReducedSingleReducedFullFullSingleReducedSingleReducedScrewed...ASME B 1.20.1Screwed...ASME B 1.20.1ButtweldASME B 16.25ButtweldASME B 16.25A351 Gr.CF8MA216 Gr.WCBA351 Gr.CF8MA276 Type 316A276 Type 316A276 Type 316A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEPTFEPTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFECarbon SteelStainless SteelCarbon SteelStainless Steel1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...21/2"1500...1/4"-11/2"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...2"1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...21/2"1500...1/2"-1"1500...11/4"-2"1000...2"Three PieceISO 5211Actuator Mounting Pad Three PieceISO 5211Actuator Mounting Pad FullFullSingleReducedSingleReducedFullSingleReducedSocket Weld...ASME B16.11Socket Weld...ASME B16.11A216 Gr.WCBA351 Gr.CF8MCarbon SteelStainless SteelSingleReducedAWSC3TFZM-OAWSC3TFZMAWSC3THZM-OAWSC3THZMAWSC3TFZM-FSOAWSC3TFZM-FSAWSC3THZM-FSOAWSC3THZM-FSAWU3TFZM-OAWU3TFZMAWU3TFZM-FSOAWU3TFZM-FSAWU3THZM-OAWU3THZMAWU3THZM-FSOAWU3THZM-FS317FS-LOH317FS317S-LOH317S319FS-LOH319FS319S-LOH319S327FS-LOH327FS329FS-LOH329FS327S-LOH327S329S-LOH329SFire SafeAnti-Static DeviceFire SafeAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8M111112113114115116117118119120121122123124125126127128129130131132133134005A216 Gr.WCBMaterial Figure Code No. WOG Type Bore Ends Body Stem Ball Gasket Ball Seat Page

1/4"

11/4" 11/2" 2" 1" 21/2" 3" 4" 5" 6" 8"3/8"1/2"3/4"51525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110product range product rangeAKSC3TFZM-OAKSC3TFZMAKSC3THZM-OAKSC3THZMAKSC3TFZM-FSOAKSC3TFZM-FSAKSC3THZM-FSOAKSC3THZM-FSAKUTKZM-FSAKUTKZM-FSOAKUTHZMAKUTHZM-OAKUTHZM-FSAKUTHZM-FSOAKUTHWZMAKUTHWZM-OAKUTHWZM-FSAKUTHWZM-FSOAKUTKMAKUTHMAKU3TFZM-OAKU3TFZMAKU3TFZM-FSOAKU3TFZM-FSAKU3THZM-OAKU3THZMAKU3THZM-FSOAKU3THZM-FSBWSC3TFZM-OBWSC3TFZMBWSC3THZM-OBWSC3THZMBWSC3TFZM-FSOBWSC3TFZM-FSBWSC3THZM-FSOBWSC3THZM-FSBWU3TFZM-OBWU3TFZMBWU3THZMBWU3TFZM-FSOBWU3TFZM-FSBWU3THZM-FSOBWU3THZM-FSAnti-Static DeviceFire SafeAnti-Static DeviceFire Safe per API607Anti-Static DeviceFire Safe per API607Fire Safe per API607Anti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceFire SafeAnti-Static Device1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"1500...1/4"-11/2"1000...2"1500...1/2"-2"1000...21/2"2000...1/4"-1"1500...11/4-2"600800Three Piece ISO 5211 Actuator Mounting PadActuator Mounting PadTwo Piece Actuator Mounting PadSeal Weld Two PieceActuator Mounting PadThree Piece ISO 5211 Actuator Mounting PadThree Piece ISO 5211 Actuator Mounting PadThree Piece ISO 5211 Actuator Mounting Pad317F-LOH317F317-LOH317319F-LOH319F319-LOH319129-LOH129-LOH227227-LOH229229-LOH247247-LOH249249-LOH5253327F-LOH327F329F-LOH329F327-LOH327329-LOH329317FB-LOH317FB317B-LOH317B319FB-LOH319FB319B-LOH319B327FB-LOH327FB327B-LOH327B329FB-LOH329FB329B-LOH329BFullSingleReducedSingleReducedFullFullSingleReducedDoubleReducedDoubleReducedSingleReducedFullFullSingleReducedSingleReducedFullFullSingleReducedSingleReducedScrewed...ASME B 1.20.1Screwed...ASME B 1.20.1ButtweldASME B 16.25ButtweldASME B 16.25A351 Gr.CF8MA216 Gr.WCBA351 Gr.CF8MA276 Type 316A276 Type 316A276 Type 316A276 Type 316A276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MA276 Type 316/A351 Gr. CF8MA276 Type 316A276 Type 316/A351 Gr. CF8MFlexible GraphiteFlexible GraphitePTFEFlexible GraphitePTFEPTFEPTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphitePTFEFlexible GraphiteHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFEHYPATITE PTFECarbon SteelStainless SteelCarbon SteelStainless Steel1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...21/2"1500...1/4"-11/2"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...2"1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/4"-3/4"1500...1"-11/2"1000...2"1500...1/2"-1"1500...11/4"-2"1000...21/2"1500...1/2"-1"1500...11/4"-2"1000...2"Three PieceISO 5211Actuator Mounting Pad Three PieceISO 5211Actuator Mounting Pad FullFullSingleReducedSingleReducedFullSingleReducedSocket Weld...ASME B16.11Socket Weld...ASME B16.11A216 Gr.WCBA351 Gr.CF8MCarbon SteelStainless SteelSingleReducedAWSC3TFZM-OAWSC3TFZMAWSC3THZM-OAWSC3THZMAWSC3TFZM-FSOAWSC3TFZM-FSAWSC3THZM-FSOAWSC3THZM-FSAWU3TFZM-OAWU3TFZMAWU3TFZM-FSOAWU3TFZM-FSAWU3THZM-OAWU3THZMAWU3THZM-FSOAWU3THZM-FS317FS-LOH317FS317S-LOH317S319FS-LOH319FS319S-LOH319S327FS-LOH327FS329FS-LOH329FS327S-LOH327S329S-LOH329SFire SafeAnti-Static DeviceFire SafeAnti-Static DeviceFire SafeAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceAnti-Static DeviceA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8MA276 TYPE 316/A351 Gr.CF8MA351 Gr.CF8M111112113114115116117118119120121122123124125126127128129130131132133134006Low Emission(ISO 15848/EPA Method 21)stem packingUpper and lowerstem bearingMetal-to-metalcontact forfre safeStem head conformwith CAPI ADDS202dimension(Double D designparallel to fow passage)ISO5211 actuatormounting padBodyExtensive safety considerationsKITZ ball valves are designed with extensive safety considerations for users. Blow-out proof stems, Secure OPEN and CLOED locking devices and prevention of misalignment of lever handles provide safe handling in the feld and trouble-free operation in the plant. Antistatic devices, fresafe seal design and cavity pressure relief features all assure the economic benefts of smooth, steady plant operation. KITZ advancements in low emission design features contribute to the global battle against fugitive emissions while greatly reducing costs caused by product loss.For sour serviceHardness of body, body cap/insert, ball and stem material of KITZ Class 150/300 steel ball valves are controlled by appropriate heat treatment and conformed to the hardness requirements in NACE MR0103, as standard.In addition to the above, following requirements are optionally available.-Bolting for valves exposed to sour environment.-NACE requirements for Class 600 and higher steel ball valves.Please contact KITZ for those requirements.004KITZ steel ball valves, foating ball designKITZ 150 / 300 SCTAM (C) / UTAM (C) Series Single Reduced Bore, Uni-body, End Entry Ball Valves003KITZ steel ball valves, foating ball designKITZ 150 / 300 SCTDZM / UTDZM Series Full Bore, Split Body, Side Entry Ball ValvesThis is an illustrated cross-section of a typical KITZ full port, split body, foating type ball valve to exhibit the basic design concept.The actual design of a valve may be slightly diferent from this illustration, depending on its size and pressure class.2" KITZ 150UTDZMThis is an illustrated cross-section of a typical KITZ regular port, uni-body, foating type ball valve to exhibit the basic design conceptThe actual design of a valve may be slightly diferent from this illustration, depending on its size and pressure class.11/2" KITZ 150SCTAM (C)Bubble-tight sealing performance with HYPATITE ball seatsHYPATITE ball seats, standard stem seals of KITZ ball valves, are made of denatured PTFE, a molecularly reinforced PTFE copolymer, and specifcally engineered for high bi-directional sealing performance and prolonged service life of valves. Its resistance to high or low temperatures, creep or compression, abrasion and corrosion is all outstanding. As an option, KITZ SWELLESS ball seats principally made of PFA are recommended specifcally for monomer service. This epoch-making new seat maximizes resistance to the permeation of monomer into its molecular structure (generally known as a "swelling" problem) which causes seat deformation and seriously afects shut-of function of valves in styrene and butadiene monomer service.Simplifed actuator mountingFor 150 / 300 SCTDZ / UTDZM and ACTA / UTAM Series ball valves,ISO 5211 actuator mounting pad is integrally provided for uniformly simplifed mounting of any actuators provided with valve mounting fanges designed to ISO 5211 dimensional requirement.Mounting pad and stem meet CAPI standard.Easy maintenanceSplit body design for KITZ SCTDZM / UTDZM Series provides the convenience of very easy maintenance critically required for process plants. Body inserts of uni-body, end entry design for KITZ 150 / 300 SCTAM (C) / UTAM (C) Series are threaded into the valve body with provision of unthreading for valve disassembly in case of maintenance operation.ISO 17292 position stopsKey lock plateLive loading springPrecisionmachined ballHYPATITE PTFE ball seatwith cavity pressure reliefprovisionLow Emissionbody seal gasketThrust washerBody capAntistatic deviceNote :Dimension of stem head are in accordance with CAPI ADDS 2.02, but the maximum specifed dimension in CAPI ADDS 2.02 is F14For NPS 8 and 10, mounting pads are F16 / ISO 5211.Stopper pinLow Emissionstem packingAntistatic deviceThrust washerBlowout-proofstem collarGland nutStem head(Double D designparallel to fow passage)Integral ISO 5211Actuator mounting padStem bearingEmission-freePTFE primary gasketFlexible graphitesecondary gasket(Fire safe type only)HYPATITE PTFEball seat with cavitypressure reliefprovisionMetal-to-metalfresafe contactKey lock plateBellevillespring washerfor live loadingPrecision machined ballBody insertBody007Low Emission(ISO 15848/EPA Method 21)stem packingUpper and lowerstem bearingMetal-to-metalcontact forfre safeStem head conformwith CAPI ADDS202dimension(Double D designparallel to fow passage)ISO5211 actuatormounting padBodyExtensive safety considerationsKITZ ball valves are designed with extensive safety considerations for users. Blow-out proof stems, Secure OPEN and CLOED locking devices and prevention of misalignment of lever handles provide safe handling in the feld and trouble-free operation in the plant. Antistatic devices, fresafe seal design and cavity pressure relief features all assure the economic benefts of smooth, steady plant operation. KITZ advancements in low emission design features contribute to the global battle against fugitive emissions while greatly reducing costs caused by product loss.For sour serviceHardness of body, body cap/insert, ball and stem material of KITZ Class 150/300 steel ball valves are controlled by appropriate heat treatment and conformed to the hardness requirements in NACE MR0103, as standard.In addition to the above, following requirements are optionally available.-Bolting for valves exposed to sour environment.-NACE requirements for Class 600 and higher steel ball valves.Please contact KITZ for those requirements.004KITZ steel ball valves, foating ball designKITZ 150 / 300 SCTAM (C) / UTAM (C) Series Single Reduced Bore, Uni-body, End Entry Ball Valves003KITZ steel ball valves, foating ball designKITZ 150 / 300 SCTDZM / UTDZM Series Full Bore, Split Body, Side Entry Ball ValvesThis is an illustrated cross-section of a typical KITZ full port, split body, foating type ball valve to exhibit the basic design concept.The actual design of a valve may be slightly diferent from this illustration, depending on its size and pressure class.2" KITZ 150UTDZMThis is an illustrated cross-section of a typical KITZ regular port, uni-body, foating type ball valve to exhibit the basic design conceptThe actual design of a valve may be slightly diferent from this illustration, depending on its size and pressure class.11/2" KITZ 150SCTAM (C)Bubble-tight sealing performance with HYPATITE ball seatsHYPATITE ball seats, standard stem seals of KITZ ball valves, are made of denatured PTFE, a molecularly reinforced PTFE copolymer, and specifcally engineered for high bi-directional sealing performance and prolonged service life of valves. Its resistance to high or low temperatures, creep or compression, abrasion and corrosion is all outstanding. As an option, KITZ SWELLESS ball seats principally made of PFA are recommended specifcally for monomer service. This epoch-making new seat maximizes resistance to the permeation of monomer into its molecular structure (generally known as a "swelling" problem) which causes seat deformation and seriously afects shut-of function of valves in styrene and butadiene monomer service.Simplifed actuator mountingFor 150 / 300 SCTDZ / UTDZM and ACTA / UTAM Series ball valves,ISO 5211 actuator mounting pad is integrally provided for uniformly simplifed mounting of any actuators provided with valve mounting fanges designed to ISO 5211 dimensional requirement.Mounting pad and stem meet CAPI standard.Easy maintenanceSplit body design for KITZ SCTDZM / UTDZM Series provides the convenience of very easy maintenance critically required for process plants. Body inserts of uni-body, end entry design for KITZ 150 / 300 SCTAM (C) / UTAM (C) Series are threaded into the valve body with provision of unthreading for valve disassembly in case of maintenance operation.ISO 17292 position stopsKey lock plateLive loading springPrecisionmachined ballHYPATITE PTFE ball seatwith cavity pressure reliefprovisionLow Emissionbody seal gasketThrust washerBody capAntistatic deviceNote :Dimension of stem head are in accordance with CAPI ADDS 2.02, but the maximum specifed dimension in CAPI ADDS 2.02 is F14For NPS 8 and 10, mounting pads are F16 / ISO 5211.Stopper pinLow Emissionstem packingAntistatic deviceThrust washerBlowout-proofstem collarGland nutStem head(Double D designparallel to fow passage)Integral ISO 5211Actuator mounting padStem bearingEmission-freePTFE primary gasketFlexible graphitesecondary gasket(Fire safe type only)HYPATITE PTFEball seat with cavitypressure reliefprovisionMetal-to-metalfresafe contactKey lock plateBellevillespring washerfor live loadingPrecision machined ballBody insertBody008004ISO 5211 Actuator Mounting PadsHYPATITE PTFE Ball SeatsOptional Ball SeatsCavity Pressure Relief005KITZ steel ball valves, foating ball designSeven Safety Considerations for KITZ 150 / 300 SCTDZM (C) / UTDZM (C) and 150 / 300 SCTAM (C) / UTAM (C) Series Ball Valves1. Double "D" stem head design provides mounting of the lever handle always in parallel to the fow passage. Misalignment of the handle is thus prevented. (Fig. 1)2. The lower end of the stem is designed with an integral collar to be blowout-proof. It also functions as the backseat for assured stem sealing. (Fig. 2)3. An antistatic feature is provided to ensure electrical continuity between ball, stem, and body. (Fig. 2)4. Facility for mounting a locking device for prevention of accidental valve operation is provided.5. Plant fres are a serious concern for soft-seated ball valves because of possible fuid leakage and consequent increase of the fre magnitude caused by deterioration of resilient sealing materials. KITZ ball valves are engineered for fre safety and successfully fre tested to minimize both external and internal fuid leakage after plant fres. They have post-fre metal-to-metal contact of all sealing areas such as: Contact between ball and valve shell (Fig. 3 & 4) Contact between stem and valve shell (Fig. 5 & 6) Valve shell coupling fanges of split body design(Fig. 7 & 8) Contact between valve body and insert of uni-body design (Fig. 9) The problem of external fuid leakage is more serious than internal leakage through the valve bore because of the fear of fueling the fre. To prevent this, KITZ ball valves may be ordered with fexible graphite packing and gaskets, which are extremely heat resistant, and not afected by the fre. For details, refer to Page 145 and 146.6. The surface of stem and stufng box, and interface clearance of stem-to-gland, stem-to-stem bearing and gland-to-stufng box are precision controlled on machining and assembly for low emission service. Materials and design of PTFE or fexible graphite packing and gasket are also carefully selected to minimize leakage of line fuid into the atmosphere. Refer to Page 145 and 146 for more information.7. A provision for cavity pressure relief is incorporated into the precision engineered KITZ HYPATITE PTFE ball seats for the ultimate safety. Refer to Page 10 for details.Flexible graphite gasket for super-fresafe provisionEmission-free PTFE primary gasketFig. 9 (Uni-body insert)Fig. 1Antistatic devicesFig. 2BodyStemBallFig. 4 (After fre)BodyMetal-to-metal contactFig. 7 (Before fre) Fig. 8 (After fre)Metal-to-metal contactBall BallGasketAs the primary body seal, emission free PTFE gasket is always provided. A Flexible graphite gasket isused as a secondary body seal for fresafe provision.KITZ 150 / 300 SCTDZM / UTDZM Series and 150 / 300 SCTAM (C) / UTAM (C) Series ball valves are furnished with an integral actuator mounting pad designed and factory-drilled according to ISO 5211 specifcation. This easily and uniformly enables mounting of any actuators provided with ISO 5211 valve mounting fanges. Mounting pad also conforms to CAPI design standard.Note: Customers are requested to prepare mounting brackets and connectors for the actuators chosen for their valve automation. Actuators can be mounted on KITZ ball valves without disassembly of valve glands.KITZ ball valves are furnished, as the manufacturer's standard, with HYPATITE PTFE ball seats made of denatured PTFE, a molecularly reinforced PTFE copolymer, and specially engineered for high performance which include:In addition to the standard HYPATITE PTFE ball seats, SWELLESS PFA seats are recommended for monomer service. Also virgin PTFE and carbon flled PTFE seats are optionally available for versatility in service applications.Some line fuid is usually left trapped inside the ball-body cavity. This fuid can expand under the infuence of high ambient or line temperature. An abnormal increase in cavity pressure can damage the valve seats or balls, unless the valve has an adequate cavity pressure relief provision. Trunnion mounted ball valves provide protection from this problem with standard seat confguration. Refer to KITZ Cat. No. K-202 for technical details of KITZ trunnion mounted ball valves.In case of foating ball valves, however, their rather simple seating principle requires some special protection from excessive cavity pressure rise when highly volatile liquidservice is subject to frequent and large temperature variation, while the valve is not frequently operated. KITZ 150 / 300 SCTDZM / UTDZM and 150 / 300 SCTAM (C) / UTAM (C) Series ball valves ofer self-relieving of excessive cavity pressure as a standard feature engineered in HYPATITE ball seats.Other general solutions for foating ball valves include employment of automatic pressure relief valves or drilling pressure equalization holes on the ball. If the requirement of automatic cavity pressure relief is as critical as in chlorine service, be sure to contact KITZ Corporation or its distributors for technical advice.Wide service temperature range of 20F through 518F.This is for standard valve design and materials used for medium to high temperature services.The lower temperature range can be extended down to 321F by means of extended bonnet design and special low temperature service materials.High chemical resistance is egual to PTFE.Monomer permeability is lower than other PTFE materials.Resistance against compression and creeping (cold fow) is higher than other PTFE materials to guarantee long life cycle.Specifc gravity and friction coefcient are equal to those of virgin PTFE for smooth valve operation.Purity of processed products is guaranteed as highly as virgin PTFE.Resiliency is as high as other PTFE materials for bubble-tight sealing performance.Refer to Page 143 and 144 for more technical data.ISO 5211 / CAPIActuator mounting padSplit body design Uni-body designActuator mounting padA typical HYPATITE PTFE seat used for 4" KITZ 150 SCTDZM ball valves.Fig. 3 (Before fre)BodySeatFig. 6 (After fre) Fig. 5 (Before fre)KITZ steel ball valves, foating ball designFlow directionHandle Top of stemFront Rearnotch groove groovePackingBearingWasherStemGasketMetal-to-metalcontact009004ISO 5211 Actuator Mounting PadsHYPATITE PTFE Ball SeatsOptional Ball SeatsCavity Pressure Relief005KITZ steel ball valves, foating ball designSeven Safety Considerations for KITZ 150 / 300 SCTDZM (C) / UTDZM (C) and 150 / 300 SCTAM (C) / UTAM (C) Series Ball Valves1. Double "D" stem head design provides mounting of the lever handle always in parallel to the fow passage. Misalignment of the handle is thus prevented. (Fig. 1)2. The lower end of the stem is designed with an integral collar to be blowout-proof. It also functions as the backseat for assured stem sealing. (Fig. 2)3. An antistatic feature is provided to ensure electrical continuity between ball, stem, and body. (Fig. 2)4. Facility for mounting a locking device for prevention of accidental valve operation is provided.5. Plant fres are a serious concern for soft-seated ball valves because of possible fuid leakage and consequent increase of the fre magnitude caused by deterioration of resilient sealing materials. KITZ ball valves are engineered for fre safety and successfully fre tested to minimize both external and internal fuid leakage after plant fres. They have post-fre metal-to-metal contact of all sealing areas such as: Contact between ball and valve shell (Fig. 3 & 4) Contact between stem and valve shell (Fig. 5 & 6) Valve shell coupling fanges of split body design(Fig. 7 & 8) Contact between valve body and insert of uni-body design (Fig. 9) The problem of external fuid leakage is more serious than internal leakage through the valve bore because of the fear of fueling the fre. To prevent this, KITZ ball valves may be ordered with fexible graphite packing and gaskets, which are extremely heat resistant, and not afected by the fre. For details, refer to Page 145 and 146.6. The surface of stem and stufng box, and interface clearance of stem-to-gland, stem-to-stem bearing and gland-to-stufng box are precision controlled on machining and assembly for low emission service. Materials and design of PTFE or fexible graphite packing and gasket are also carefully selected to minimize leakage of line fuid into the atmosphere. Refer to Page 145 and 146 for more information.7. A provision for cavity pressure relief is incorporated into the precision engineered KITZ HYPATITE PTFE ball seats for the ultimate safety. Refer to Page 10 for details.Flexible graphite gasket for super-fresafe provisionEmission-free PTFE primary gasketFig. 9 (Uni-body insert)Fig. 1Antistatic devicesFig. 2BodyStemBallFig. 4 (After fre)BodyMetal-to-metal contactFig. 7 (Before fre) Fig. 8 (After fre)Metal-to-metal contactBall BallGasketAs the primary body seal, emission free PTFE gasket is always provided. A Flexible graphite gasket isused as a secondary body seal for fresafe provision.KITZ 150 / 300 SCTDZM / UTDZM Series and 150 / 300 SCTAM (C) / UTAM (C) Series ball valves are furnished with an integral actuator mounting pad designed and factory-drilled according to ISO 5211 specifcation. This easily and uniformly enables mounting of any actuators provided with ISO 5211 valve mounting fanges. Mounting pad also conforms to CAPI design standard.Note: Customers are requested to prepare mounting brackets and connectors for the actuators chosen for their valve automation. Actuators can be mounted on KITZ ball valves without disassembly of valve glands.KITZ ball valves are furnished, as the manufacturer's standard, with HYPATITE PTFE ball seats made of denatured PTFE, a molecularly reinforced PTFE copolymer, and specially engineered for high performance which include:In addition to the standard HYPATITE PTFE ball seats, SWELLESS PFA seats are recommended for monomer service. Also virgin PTFE and carbon flled PTFE seats are optionally available for versatility in service applications.Some line fuid is usually left trapped inside the ball-body cavity. This fuid can expand under the infuence of high ambient or line temperature. An abnormal increase in cavity pressure can damage the valve seats or balls, unless the valve has an adequate cavity pressure relief provision. Trunnion mounted ball valves provide protection from this problem with standard seat confguration. Refer to KITZ Cat. No. K-202 for technical details of KITZ trunnion mounted ball valves.In case of foating ball valves, however, their rather simple seating principle requires some special protection from excessive cavity pressure rise when highly volatile liquidservice is subject to frequent and large temperature variation, while the valve is not frequently operated. KITZ 150 / 300 SCTDZM / UTDZM and 150 / 300 SCTAM (C) / UTAM (C) Series ball valves ofer self-relieving of excessive cavity pressure as a standard feature engineered in HYPATITE ball seats.Other general solutions for foating ball valves include employment of automatic pressure relief valves or drilling pressure equalization holes on the ball. If the requirement of automatic cavity pressure relief is as critical as in chlorine service, be sure to contact KITZ Corporation or its distributors for technical advice.Wide service temperature range of 20F through 518F.This is for standard valve design and materials used for medium to high temperature services.The lower temperature range can be extended down to 321F by means of extended bonnet design and special low temperature service materials.High chemical resistance is egual to PTFE.Monomer permeability is lower than other PTFE materials.Resistance against compression and creeping (cold fow) is higher than other PTFE materials to guarantee long life cycle.Specifc gravity and friction coefcient are equal to those of virgin PTFE for smooth valve operation.Purity of processed products is guaranteed as highly as virgin PTFE.Resiliency is as high as other PTFE materials for bubble-tight sealing performance.Refer to Page 143 and 144 for more technical data.ISO 5211 / CAPIActuator mounting padSplit body design Uni-body designActuator mounting padA typical HYPATITE PTFE seat used for 4" KITZ 150 SCTDZM ball valves.Fig. 3 (Before fre)BodySeatFig. 6 (After fre) Fig. 5 (Before fre)KITZ steel ball valves, foating ball designFlow directionHandle Top of stemFront Rearnotch groove groovePackingBearingWasherStemGasketMetal-to-metalcontact010008 007KITZ steel ball valves, foating ball design KITZ steel ball valves, foating ball designLow Emission Design Features for KITZ 150 / 300 SCTDZM / UTDZM and 150 / 300 SCTAM (C) / UTAM (C) Series Ball ValvesKITZ General Term of Warranty for Low Emission Service ValvesDiametrical interface clearanceThe diametricalis strictly controlled to prevent the line fuid from leaking into the atmosphere through these potential leak paths.The optimum diametrical clearance is realized on the following area by high precision machining. Gland and Stem Gland and Stufng Box Stem and BearingStemThe stem surface fnish is controlled according to KITZ design and manufacturing standards. This specifcation is particularly important for fexible graphite packing, because, while the stem travels through the packing rings, graphite tends to fll micro scratches on the stem surface and migrates to the stem to function as a lubricant. Too fne a stem smoothness loses this advantage and can increase leakage. The stem straightness and roundness are also controlled according to our design and manufacturing standards.Stufng boxThe surface fnish is according to KITZ design and manufacturing standards. Contrary to the stem, the stufng box wall statically contacts packing rings, and a reasonably rougher surface fnish results in a better sealing performance. The cylindricity and verticality are precision controlled according to KITZ design and manufacturing standards.GasketPTFE gasket is used for standard version. Graphite gasket is used for the optional fre safe version and high temperature low emission service respectively. The gasket contact faces of valve shells are precision machined to further upgrade the sealing function of the valve shell joint.KITZ high engineered sealing design achieves superior fugitive emission performance.ISO 15848-1qualifed. KITZ precise laboratory tests and various feld experiences achieve the optimized new stem sealing design for superior fugitive emission performance. That is proven on the certifcate of ISO 15848-1 Tightness Class BH qualifcation test, witnessed by Bureau Veritas. This is KITZ standard specifcation for Class 150 and 300 fanged foating ball valves,identifed as 150 / 300 UTDZ / SCTDZ Series (split body, side entry design) in this catalog.ISO 15848-1 QualifcationGland packingA conventional type of die formed packing ring is entirely made of many layers of vertically wrapped graphite tape.Interlayer and through-graphite permeation of line fuid in the vertical axis direction is rather an inherent problem on the conventional type of die formed packing rings.To solve this problem, a unique design is employed on the KITZ Graphite Packing Rings for Low Emission Service.Vertically and horizontally wrapped graphite tapes are securely fxed into the ring structure of KITZ Graphite Packing Rings for Low Emission Service, as shown in Fig (*).Stem seal mechanism for 150 / 300 SCTDZM / UTDZM 21/2" and largerKITZ Graphite Packing Ringsfor Low Emission ServiceWarranty Period12 months after placement in service, but not exceeding 18 months after shipment from KITZ factories.Warranty Conditions1. Proper storage and maintenance of valves prior to installation, according to the KITZ maintenance manual.2. Proper handling of valves during transportation and plant construction, which includes sandblasting and painting, for protection of exposed stems and glands of valves.3. Need of adequate retightening of gland packing sets* according to the KITZ maintenance manual to reduce the leak level, when an excessive level of fugitive emission is detected during:a) Pre-installation valve inspectionb) Process pilot run or start-up operationc) Periodic or occasional inspection of valves in service4. Valve stems must be kept free of scratches, scars or corrosion.5. Following all other instructions provided in the KITZ maintenance and operation manuals.* This condition is particularly important when valves are subjected to thermal cycles on the site. Users are recommended to ensure that packing is retightened after every cool-down of the process.Conventional Die Formed Packing RingsClass Series SeatPackingGasketTightnessClassTemperatureClassEnduranceClass150SCTDZUTDZPTFEB *1B *1CO 3 *2CO 3 *2-29200(-20392)-29200(-20392)300SCTDZ-FSUTDZ-FSFlexible GraphiteHYPATITE PTFEHYPATITE PTFE*1 ISO 15848-1 remarks that tightness class A typically achieved with bellow seals, class B with PTFE packing and class C with fexible graphite packing.*2 CO 3 includes 2,500 cycle operation and 4 times thermal cycle.CAA / EPA Method 21 (40 CFR. 60 Appendix A)The US Federal Clean Air Act requires all plants handling the toxic gases and chemicals listed by the Environmental Protection Agency (EPA)to periodically monitor their plant equipment for detection of fugitive emissions exceeding criteria, and repair or replace all defective equipment immediately.The criteria of emission are categorized in detail by the emission sources (equipment) and/or listed fuid type.Some state regulations, such as California, require more stringent emission control that is reaching 50 ppm maximum leak level.KITZ low emission service ball valves are designed, engineered, manufactured and tested to meet these emission levelas standard product for KITZ 150 / 300 UTDZ / SCTDZ and UTAM(C) / SCTAM(C)*2 Series Ball Valves.Our low emission valve performance and laboratory test results are shown on the below table*1.Laboratory Test ResultsClass Series SeatPackingGasketMaximum leak levelon new valveTest result after10,000 cycle operation150SCTDZUTDZBody TypeSplit-bodyPTFE50ppm20ppm50ppm *350ppm *3300SCTDZ-FSUTDZ-FSFlexible GraphiteHYPATITE PTFEHYPATITE PTFE*1 Maximum leak level guaranteed for the duration of the KITZ warranty in North America for emission monitoring with EPA Method 21 procedures and methane-calibrated organic vapor analyzers.*2 Except 1" and smaller sizes, which are provided with only one piece of packing ring due to limited stufng box dimension.*3 Maximum leak level was measured with clean fuid at ambient room temperature, and with adequate gland bolts retightening according to KITZ maintenance manual.Major design considerations for having upgraded our standard valves to the low emission performer are introduced below:INCONEL is registered trademark of SPECIAL METALPermeationStem StemISO 15848-1CertifcateO-ringPackingStem bearingGland boltGland011008 007KITZ steel ball valves, foating ball design KITZ steel ball valves, foating ball designLow Emission Design Features for KITZ 150 / 300 SCTDZM / UTDZM and 150 / 300 SCTAM (C) / UTAM (C) Series Ball ValvesKITZ General Term of Warranty for Low Emission Service ValvesDiametrical interface clearanceThe diametricalis strictly controlled to prevent the line fuid from leaking into the atmosphere through these potential leak paths.The optimum diametrical clearance is realized on the following area by high precision machining. Gland and Stem Gland and Stufng Box Stem and BearingStemThe stem surface fnish is controlled according to KITZ design and manufacturing standards. This specifcation is particularly important for fexible graphite packing, because, while the stem travels through the packing rings, graphite tends to fll micro scratches on the stem surface and migrates to the stem to function as a lubricant. Too fne a stem smoothness loses this advantage and can increase leakage. The stem straightness and roundness are also controlled according to our design and manufacturing standards.Stufng boxThe surface fnish is according to KITZ design and manufacturing standards. Contrary to the stem, the stufng box wall statically contacts packing rings, and a reasonably rougher surface fnish results in a better sealing performance. The cylindricity and verticality are precision controlled according to KITZ design and manufacturing standards.GasketPTFE gasket is used for standard version. Graphite gasket is used for the optional fre safe version and high temperature low emission service respectively. The gasket contact faces of valve shells are precision machined to further upgrade the sealing function of the valve shell joint.KITZ high engineered sealing design achieves superior fugitive emission performance.ISO 15848-1qualifed. KITZ precise laboratory tests and various feld experiences achieve the optimized new stem sealing design for superior fugitive emission performance. That is proven on the certifcate of ISO 15848-1 Tightness Class BH qualifcation test, witnessed by Bureau Veritas. This is KITZ standard specifcation for Class 150 and 300 fanged foating ball valves,identifed as 150 / 300 UTDZ / SCTDZ Series (split body, side entry design) in this catalog.ISO 15848-1 QualifcationGland packingA conventional type of die formed packing ring is entirely made of many layers of vertically wrapped graphite tape.Interlayer and through-graphite permeation of line fuid in the vertical axis direction is rather an inherent problem on the conventional type of die formed packing rings.To solve this problem, a unique design is employed on the KITZ Graphite Packing Rings for Low Emission Service.Vertically and horizontally wrapped graphite tapes are securely fxed into the ring structure of KITZ Graphite Packing Rings for Low Emission Service, as shown in Fig (*).Stem seal mechanism for 150 / 300 SCTDZM / UTDZM 21/2" and largerKITZ Graphite Packing Ringsfor Low Emission ServiceWarranty Period12 months after placement in service, but not exceeding 18 months after shipment from KITZ factories.Warranty Conditions1. Proper storage and maintenance of valves prior to installation, according to the KITZ maintenance manual.2. Proper handling of valves during transportation and plant construction, which includes sandblasting and painting, for protection of exposed stems and glands of valves.3. Need of adequate retightening of gland packing sets* according to the KITZ maintenance manual to reduce the leak level, when an excessive level of fugitive emission is detected during:a) Pre-installation valve inspectionb) Process pilot run or start-up operationc) Periodic or occasional inspection of valves in service4. Valve stems must be kept free of scratches, scars or corrosion.5. Following all other instructions provided in the KITZ maintenance and operation manuals.* This condition is particularly important when valves are subjected to thermal cycles on the site. Users are recommended to ensure that packing is retightened after every cool-down of the process.Conventional Die Formed Packing RingsClass Series SeatPackingGasketTightnessClassTemperatureClassEnduranceClass150SCTDZUTDZPTFEB *1B *1CO 3 *2CO 3 *2-29200(-20392)-29200(-20392)300SCTDZ-FSUTDZ-FSFlexible GraphiteHYPATITE PTFEHYPATITE PTFE*1 ISO 15848-1 remarks that tightness class A typically achieved with bellow seals, class B with PTFE packing and class C with fexible graphite packing.*2 CO 3 includes 2,500 cycle operation and 4 times thermal cycle.CAA / EPA Method 21 (40 CFR. 60 Appendix A)The US Federal Clean Air Act requires all plants handling the toxic gases and chemicals listed by the Environmental Protection Agency (EPA)to periodically monitor their plant equipment for detection of fugitive emissions exceeding criteria, and repair or replace all defective equipment immediately.The criteria of emission are categorized in detail by the emission sources (equipment) and/or listed fuid type.Some state regulations, such as California, require more stringent emission control that is reaching 50 ppm maximum leak level.KITZ low emission service ball valves are designed, engineered, manufactured and tested to meet these emission levelas standard product for KITZ 150 / 300 UTDZ / SCTDZ and UTAM(C) / SCTAM(C)*2 Series Ball Valves.Our low emission valve performance and laboratory test results are shown on the below table*1.Laboratory Test ResultsClass Series SeatPackingGasketMaximum leak levelon new valveTest result after10,000 cycle operation150SCTDZUTDZBody TypeSplit-bodyPTFE50ppm20ppm50ppm *350ppm *3300SCTDZ-FSUTDZ-FSFlexible GraphiteHYPATITE PTFEHYPATITE PTFE*1 Maximum leak level guaranteed for the duration of the KITZ warranty in North America for emission monitoring with EPA Method 21 procedures and methane-calibrated organic vapor analyzers.*2 Except 1" and smaller sizes, which are provided with only one piece of packing ring due to limited stufng box dimension.*3 Maximum leak level was measured with clean fuid at ambient room temperature, and with adequate gland bolts retightening according to KITZ maintenance manual.Major design considerations for having upgraded our standard valves to the low emission performer are introduced below:INCONEL is registered trademark of SPECIAL METALPermeationStem StemISO 15848-1CertifcateO-ringPackingStem bearingGland boltGland012010KITZ steel ball valves, foating ball design KITZ steel ball valves, foating ball designPressure-Temperature RatingsThe pressure-temperature ratings of ball valves are determined, not only by valve shell materials, but more essentially by sealing materials used for ball seats, gland packing and gaskets. Sealing materials may be high molecule plastics or rubbers, but the choice is limited by the characteristics of the service fuid, working temperatures, working pressures, velocity of fuid, and operational frequency of valves.As it is very difcult to predetermine the exact pressure-temperature rating for all kinds of fuid under all imaginable conditions, we have prepared general rating charts for non-shock fuid service here, based on our past experiences both in the feld and in our laboratory. In case of extraordinary service conditions as mentioned below, contact KITZ Corporation or its distributors for technical advice:1. Valves shall be left fully closed for a long period of time under high temperature or high diferential pressure.2. Valves shall be frequently operated under high temperature or high diferential pressure.3. Frequent change of line pressure or temperature.Seat materials A : Virgin PTFE B: HYPATITE PTFE, Carbon-flled PTFE, or SWELLESS. HYPATITE is the standard seat material for KITZ ball valves. Specify virgin PTFE or carbon-flled PTFE when required. The body pressure ratings shown here are for ASTM A216 Gr. WCB. For the pressure ratings of other valve shell materials, refer to the latest edition of ASME B16.34.MPa012345678 -20 100 200 300 400 500 572020040060080010001160psiClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingTemperaturePressureTDZ Series : 1/2" ,3/4"A BMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 3" , 4"Class 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingA BMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series :1"21/2"MPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 5" , 6"ABMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 8" , 10"Class 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingABClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingA B Class 300 WCB body rationgClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingMPa01.963.925.115.886.08 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 1/2" to 1" Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingA BMPa01.963.925.115.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 4" & 6"A BMPa01.963.925.115.005.305.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 11/2" to 3"MPa01.963.925.115.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 8" & 10" Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingA B Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingNote*Note* Continuous service in high diferential pressure exceeding 580psig for these valves may cause ball seat degradation or shortening life. Trunnion mounted ball valve would be recommended for following services. 1) Alternate pressurization from both valve end exceeding 580psig 2) Both high(exceeding 580psig)and low(less than 145psig)pressure tight shut of required services. 3) Frequent breakaway operations over 500times under the high diferential pressure exceeding 580psig.013010KITZ steel ball valves, foating ball design KITZ steel ball valves, foating ball designPressure-Temperature RatingsThe pressure-temperature ratings of ball valves are determined, not only by valve shell materials, but more essentially by sealing materials used for ball seats, gland packing and gaskets. Sealing materials may be high molecule plastics or rubbers, but the choice is limited by the characteristics of the service fuid, working temperatures, working pressures, velocity of fuid, and operational frequency of valves.As it is very difcult to predetermine the exact pressure-temperature rating for all kinds of fuid under all imaginable conditions, we have prepared general rating charts for non-shock fuid service here, based on our past experiences both in the feld and in our laboratory. In case of extraordinary service conditions as mentioned below, contact KITZ Corporation or its distributors for technical advice:1. Valves shall be left fully closed for a long period of time under high temperature or high diferential pressure.2. Valves shall be frequently operated under high temperature or high diferential pressure.3. Frequent change of line pressure or temperature.Seat materials A : Virgin PTFE B: HYPATITE PTFE, Carbon-flled PTFE, or SWELLESS. HYPATITE is the standard seat material for KITZ ball valves. Specify virgin PTFE or carbon-flled PTFE when required. The body pressure ratings shown here are for ASTM A216 Gr. WCB. For the pressure ratings of other valve shell materials, refer to the latest edition of ASME B16.34.MPa012345678 -20 100 200 300 400 500 572020040060080010001160psiClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingTemperaturePressureTDZ Series : 1/2" ,3/4"A BMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 3" , 4"Class 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingA BMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series :1"21/2"MPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 5" , 6"ABMPa012345678 -20 100 200 300 400 500 572020040060080010001160psiTemperaturePressureTDZ Series : 8" , 10"Class 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingABClass 300 WCB body ratingClass 300 CF8M body ratingClass 150 WCB body ratingClass 150 CF8M body ratingA B Class 300 WCB body rationgClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingMPa01.963.925.115.886.08 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 1/2" to 1" Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingA BMPa01.963.925.115.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 4" & 6"A BMPa01.963.925.115.005.305.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 11/2" to 3"MPa01.963.925.115.88 -20 100 200 300 400 500 57202004006008001000psiTemperaturePressure150 / 300 SCTA / UTAM : 8" & 10" Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingA B Class 300 WCB body ratingClass 150 WCB body ratingClass 150 CF8M body ratingClass 300 CF8M body ratingNote*Note* Continuous service in high diferential pressure exceeding 580psig for these valves may cause ball seat degradation or shortening life. Trunnion mounted ball valve would be recommended for following services. 1) Alternate pressurization from both valve end exceeding 580psig 2) Both high(exceeding 580psig)and low(less than 145psig)pressure tight shut of required services. 3) Frequent breakaway operations over 500times under the high diferential pressure exceeding 580psig.014BODYBODY CAPSTEMBALLGLANDGLAND PACKIINGHANDLEHANDLE BARHANDLE HEADNAME PLATELEV PLATEGASKETPACKING WASHERBALL SEATCAP NUTCAP BOLTGLAND BOLTKEYLOCK PLATEHANDLELOCK PLATESNAP RINGSTOPPERSTOPPER PLATEGLAND BUSHGLAND WASHERSTEM BEARINGHANDLELOCK PLATE BOLTHANDLE BOLTSPRING & PINSTOPPER PLATE BOLT CONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A276 TYPE316 or A351 Gr. CF8MA351 Gr. CF8150SCTDZM(C)PTFE150SCTDZM-FS(C)FLEXIBLE GRAPHITEDUCTILE IRON(UP TO SIZE 5)CARBON STEEL(SIZE 6 & OVER)DUCTILE IRON(SIZE 6 & OVER)A276 TYPE304A276 TYPE304150SCTDZM(C)PTFE150SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE316L(UP TO SIZE 1)HYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELA276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304G/F PTFEA276 TYPE304G/F PTFESTAINLESS STEELSTAINLESS STEELA313 & A276 TYPE316STAINLESS STEELInconel 718 or EquivalentA276 TYPE304(SIZE 11/2 & OVER)A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347899916161920303335364043484951575867123123124126145216216ABABABABNominal SizeUnit : inch0.550.750.951.501.972.523.003.944.845.957.95d15202540506580100125150200mm1/23/4111/2221/234568in.4.254.374.885.285.637.057.448.829.4512.4015.98H5.125.127.099.069.0615.7515.7518.1118.1139.3759.06D14.254.625.006.507.007.508.009.0014.0015.5018.00L3.503.884.255.006.007.007.509.0010.0011.0013.50D2.382.753.123.884.755.506.007.508.509.5011.75C44444448888No.0.620.620.620.620.750.750.750.750.880.880.88h1/21/21/21/25/85/85/85/83/43/43/4Bolt Size1.381.692.002.883.624.125.006.197.318.5010.62g0.440.440.440.560.620.690.750.940.941.001.12t0.060.060.060.060.060.060.060.060.060.060.06f0.360.360.550.670.670.870.871.061.061.421.81A0.470.470.710.870.871.101.101.421.421.892.360.990.991.382.172.172.762.763.353.353.945.12B1.421.421.972.762.764.024.024.924.925.516.50E F0.350.350.550.670.670.870.871.061.061.421.81G0.870.871.181.341.341.771.772.052.052.483.11K0.040.040.060.060.060.080.080.080.080.080.08TM5M5M6M8M8M10M10M12M12M16M20UF03F03F05F07F07F10F10F12F12F14F16ISO 5211Flange Typeclass 150 cast steel ball valves150SCTDZM150SCTDZM-FSEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONSpsig3500300025002000150010005000-20 0 50 100 150 200 250 300 350 400 450 482 (F)PressureClass 600 / 1500 SCTBM / UTBMClass 1500 WCB body ratingClass 1500 WCB body ratingClass 1500 CF8M body ratingClass 600 WCB body ratingClass 600 CF8M body ratingQ(}(Ball Seat MaterialsQ KITZ HYPATITE or Carbon-flled PTFE Glass-flled PTFE with MoS2 Virgin PTFE( Nylon with MoS2O-ring Upper Limit(1) FKM(2) Low-temperature FKM}(1) EPDM(2) ECO (Epichlorohydrin Copolymer)(1) NBR(2) Low-temperature NBRO-ring Lower Limit *( FKM* O-rings made of others than FKM can withstand -20F.Temperaturepsig2000150010005000-20 0 100 200 300 400 500 572 (F)PressureType 1500 / 1000 SC3THZM / U3THZMSC3TFZM / U3TFZMQQ Single Reduced Bore up to 2Full port up to 11/2 Single Reduced Bore 21/2Full port 2psig10008006004002000-20 0 100 200 300 400 500 572 (F)TemperaturePressureType 800 UTHM / 1000UTFMSeat: PTFEpsig10008006004002000-20 0 100 200 300 400 500 572 (F)TemperaturePressureType 600 UTKM / SCTKMSeat: Reinforced PTFEType 2000 / 1500 SCTKZM / UTKZMSCTHZM / UTHZMSCTHWZM / UTHWZMQ Size 1/4 ~ 1 Size 11/4 ~ 2psig2000150010005000-20 0 100 200 300 400 500 572 (F)TemperaturePressureQUTHMUTFM009KITZ steel ball valves, foating ball design015BODYBODY CAPSTEMBALLGLANDGLAND PACKIINGHANDLEHANDLE BARHANDLE HEADNAME PLATELEV PLATEGASKETPACKING WASHERBALL SEATCAP NUTCAP BOLTGLAND BOLTKEYLOCK PLATEHANDLELOCK PLATESNAP RINGSTOPPERSTOPPER PLATEGLAND BUSHGLAND WASHERSTEM BEARINGHANDLELOCK PLATE BOLTHANDLE BOLTSPRING & PINSTOPPER PLATE BOLT CONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A276 TYPE316 or A351 Gr. CF8MA351 Gr. CF8150SCTDZM(C)PTFE150SCTDZM-FS(C)FLEXIBLE GRAPHITEDUCTILE IRON(UP TO SIZE 5)CARBON STEEL(SIZE 6 & OVER)DUCTILE IRON(SIZE 6 & OVER)A276 TYPE304A276 TYPE304150SCTDZM(C)PTFE150SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE316L(UP TO SIZE 1)HYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELA276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304G/F PTFEA276 TYPE304G/F PTFESTAINLESS STEELSTAINLESS STEELA313 & A276 TYPE316STAINLESS STEELInconel 718 or EquivalentA276 TYPE304(SIZE 11/2 & OVER)A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347899916161920303335364043484951575867123123124126145216216ABABABABNominal SizeUnit : inch0.550.750.951.501.972.523.003.944.845.957.95d15202540506580100125150200mm1/23/4111/2221/234568in.4.254.374.885.285.637.057.448.829.4512.4015.98H5.125.127.099.069.0615.7515.7518.1118.1139.3759.06D14.254.625.006.507.007.508.009.0014.0015.5018.00L3.503.884.255.006.007.007.509.0010.0011.0013.50D2.382.753.123.884.755.506.007.508.509.5011.75C44444448888No.0.620.620.620.620.750.750.750.750.880.880.88h1/21/21/21/25/85/85/85/83/43/43/4Bolt Size1.381.692.002.883.624.125.006.197.318.5010.62g0.440.440.440.560.620.690.750.940.941.001.12t0.060.060.060.060.060.060.060.060.060.060.06f0.360.360.550.670.670.870.871.061.061.421.81A0.470.470.710.870.871.101.101.421.421.892.360.990.991.382.172.172.762.763.353.353.945.12B1.421.421.972.762.764.024.024.924.925.516.50E F0.350.350.550.670.670.870.871.061.061.421.81G0.870.871.181.341.341.771.772.052.052.483.11K0.040.040.060.060.060.080.080.080.080.080.08TM5M5M6M8M8M10M10M12M12M16M20UF03F03F05F07F07F10F10F12F12F14F16ISO 5211Flange Typeclass 150 cast steel ball valves150SCTDZM150SCTDZM-FSEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONSpsig3500300025002000150010005000-20 0 50 100 150 200 250 300 350 400 450 482 (F)PressureClass 600 / 1500 SCTBM / UTBMClass 1500 WCB body ratingClass 1500 WCB body ratingClass 1500 CF8M body ratingClass 600 WCB body ratingClass 600 CF8M body ratingQ(}(Ball Seat MaterialsQ KITZ HYPATITE or Carbon-flled PTFE Glass-flled PTFE with MoS2 Virgin PTFE( Nylon with MoS2O-ring Upper Limit(1) FKM(2) Low-temperature FKM}(1) EPDM(2) ECO (Epichlorohydrin Copolymer)(1) NBR(2) Low-temperature NBRO-ring Lower Limit *( FKM* O-rings made of others than FKM can withstand -20F.Temperaturepsig2000150010005000-20 0 100 200 300 400 500 572 (F)PressureType 1500 / 1000 SC3THZM / U3THZMSC3TFZM / U3TFZMQQ Single Reduced Bore up to 2Full port up to 11/2 Single Reduced Bore 21/2Full port 2psig10008006004002000-20 0 100 200 300 400 500 572 (F)TemperaturePressureType 800 UTHM / 1000UTFMSeat: PTFEpsig10008006004002000-20 0 100 200 300 400 500 572 (F)TemperaturePressureType 600 UTKM / SCTKMSeat: Reinforced PTFEType 2000 / 1500 SCTKZM / UTKZMSCTHZM / UTHZMSCTHWZM / UTHWZMQ Size 1/4 ~ 1 Size 11/4 ~ 2psig2000150010005000-20 0 100 200 300 400 500 572 (F)TemperaturePressureQUTHMUTFM009KITZ steel ball valves, foating ball design016BODYSTEMBALLGLANDGLAND PACKINGHANDLEHANDLE NUTNUTNAME PLATEGASKETGASKETINSERTBALL SEATKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSTEM BEARINGRING SPRINGSTOPPER PINA216 Gr. WCBA276 TYPE 316A276 TYPE 316A276 TYPE 316150SCTAM (C)PTFE150SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELPTFE150SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCBHYPATITE PTFESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELC/F PTFE (SIZE 1 ONLY)C/F PTFE (SIZE 1/2 & 3/4)STAINLESS STEELSTAINLESS STEELMaterials Name of Parts No.MATERIAL LIST134789101016191929304043434767124126ABABABNominal SizeUnit : inch0.490.750.98d0.390.490.67d1152025mm1/23/41in.3.503.583.94H5.525.526.30D14.254.635.00L3.503.884.25D2.382.753.12C444No.0.620.620.62h1/21/21/2Bolt Size1.381.692.00g0.440.440.44t0.060.060.06f0.280.280.36A0.390.390.470.990.990.99B1.421.421.42E F0.290.290.37G0.650.650.85K0.060.060.06T1/4-20UNC1/4-20UNC1/4-20UNCUF03(2)F03(2)F03ISO 5211Flange Typeclass 150 cast steel ball valves class 150 cast steel ball valves150SCTAM (C)150SCTAM-FS (C)NOTE(1) All valves have an anti-static thrust washer or stem bearing insuring positive conductivity between body and stem.(2) Dimensions A and B are in accordance with CAPI F03-S.End Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONSG-150SCTDZM G-150SCTDZM-FSBODYBODY CAPSTEMBALLGLANDGLAND PACKIINGNAME PLATELEV PLATEGASKETBALL SEATCAP NUTCAP BOLTGLAND BOLTGLAND BUSHGLAND WASHERSTEM BEARINGCONNECTORBRAKETBOLTGEAR UNITSPRING & PINCONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A351 Gr. CF8MA351 Gr. CF8G-150SCTDZM(C)PTFEG-150SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE304A276 TYPE304G-150SCTDZM(C)PTFEG-150SCTDZM-FS(C)FLEXIBLE GRAPHITEHYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELG/F PTFEA276 TYPE304G/F PTFECARBON STEELDUCTILE IRONSTAINLESS STTELA313 & A276 TYPE316Inconel 718 or EquivalentA276 TYPE304A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347816161930333536575867929399102124145216216ABABNominal SizeUnit : inch9.96d250mm10in.17.64H19.69D121.00L16.00D14.25C12No.1.00h7/8Bolt Size12.75g1.19t0.06f1.81A14.29Q3.68P2.36 5.12B6.50E F1.81G3.07K0.08TM20UF16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONS017BODYSTEMBALLGLANDGLAND PACKINGHANDLEHANDLE NUTNUTNAME PLATEGASKETGASKETINSERTBALL SEATKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSTEM BEARINGRING SPRINGSTOPPER PINA216 Gr. WCBA276 TYPE 316A276 TYPE 316A276 TYPE 316150SCTAM (C)PTFE150SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELPTFE150SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCBHYPATITE PTFESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELC/F PTFE (SIZE 1 ONLY)C/F PTFE (SIZE 1/2 & 3/4)STAINLESS STEELSTAINLESS STEELMaterials Name of Parts No.MATERIAL LIST134789101016191929304043434767124126ABABABNominal SizeUnit : inch0.490.750.98d0.390.490.67d1152025mm1/23/41in.3.503.583.94H5.525.526.30D14.254.635.00L3.503.884.25D2.382.753.12C444No.0.620.620.62h1/21/21/2Bolt Size1.381.692.00g0.440.440.44t0.060.060.06f0.280.280.36A0.390.390.470.990.990.99B1.421.421.42E F0.290.290.37G0.650.650.85K0.060.060.06T1/4-20UNC1/4-20UNC1/4-20UNCUF03(2)F03(2)F03ISO 5211Flange Typeclass 150 cast steel ball valves class 150 cast steel ball valves150SCTAM (C)150SCTAM-FS (C)NOTE(1) All valves have an anti-static thrust washer or stem bearing insuring positive conductivity between body and stem.(2) Dimensions A and B are in accordance with CAPI F03-S.End Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONSG-150SCTDZM G-150SCTDZM-FSBODYBODY CAPSTEMBALLGLANDGLAND PACKIINGNAME PLATELEV PLATEGASKETBALL SEATCAP NUTCAP BOLTGLAND BOLTGLAND BUSHGLAND WASHERSTEM BEARINGCONNECTORBRAKETBOLTGEAR UNITSPRING & PINCONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A351 Gr. CF8MA351 Gr. CF8G-150SCTDZM(C)PTFEG-150SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE304A276 TYPE304G-150SCTDZM(C)PTFEG-150SCTDZM-FS(C)FLEXIBLE GRAPHITEHYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELG/F PTFEA276 TYPE304G/F PTFECARBON STEELDUCTILE IRONSTAINLESS STTELA313 & A276 TYPE316Inconel 718 or EquivalentA276 TYPE304A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347816161930333536575867929399102124145216216ABABNominal SizeUnit : inch9.96d250mm10in.17.64H19.69D121.00L16.00D14.25C12No.1.00h7/8Bolt Size12.75g1.19t0.06f1.81A14.29Q3.68P2.36 5.12B6.50E F1.81G3.07K0.08TM20UF16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONS018class 150 cast steel ball valves class 300 cast steel ball valves300SCTDZM300SCTDZM-FSNominal SizeUnit : inch0.550.750.951.501.972.523.003.945.957.95d15202540506580100150200mm1/23/4111/2221/23468in.4.254.374.885.285.637.057.448.8212.4015.98H5.125.127.099.069.0615.7515.7529.5339.3759.06D15.506.006.507.508.509.5011.1212.0015.8819.75L3.754.624.886.146.507.508.2510.0012.5015.00D2.623.253.504.505.005.886.627.8810.6213.00C444488881212No.0.620.750.750.880.750.880.880.880.881.00h1/25/85/83/45/83/43/43/43/47/8Bolt Size1.381.692.002.883.624.125.006.198.5010.62g0.560.620.690.810.881.001.121.251.441.62t0.060.060.060.060.060.060.060.060.060.06f0.360.360.550.670.670.870.871.061.421.81A0.470.470.710.870.871.101.101.421.892.360.990.991.382.172.172.762.763.353.945.12B1.421.421.972.762.764.024.024.925.516.50E F0.350.350.550.670.670.870.871.061.421.81G0.870.871.181.341.341.771.772.052.483.11K0.040.040.060.060.060.080.080.080.080.08TM5M5M6M8M8M10M10M12M16M20UF03F03F05F07F07F10F10F12F14F16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleBODYBODY CAPSTEMBALLGLANDGLAND PACKIINGHANDLEHANDLE BARHANDLE HEADNAME PLATELEV PLATEGASKETPACKING WASHERBALL SEATCAP NUTCAP BOLTGLAND BOLTKEYLOCK PLATEHANDLELOCK PLATESNAP RINGSTOPPERSTOPPER PLATEGLAND BUSHGLAND WASHERSTEM BEARINGHANDLELOCK PLATE BOLTHANDLE BOLTSPRING & PINSTOPPER PLATE BOLT CONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A276 TYPE316 or A351 Gr. CF8MA351 Gr. CF8300SCTDZM(C)PTFE300SCTDZM-FS(C)FLEXIBLE GRAPHITEDUCTILE IRON(UP TO SIZE 3)CARBON STEEL(SIZE 4 & OVER)DUCTILE IRON(SIZE 4 & OVER)A276 TYPE304A276 TYPE304300SCTDZM(C)PTFE300SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE316L(UP TO SIZE 1)HYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELA276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304G/F PTFEA276 TYPE304G/F PTFESTAINLESS STEELSTAINLESS STEELA313 & A276 TYPE316STAINLESS STEELInconel 718 or EquivalentA276 TYPE304(SIZE 11/2 & OVER)A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347899916161920303335364043484951575867123123124126145216216ABABABABDIMENSIONS150SCTAM (C)150SCTAM-FS (C)BODYSTEMBALLGLANDGLANDGLAND PACKINGGLAND PACKINGHANDLEHANDLE BARHANDLE HEADHANDLE NUTNUTNAME PLATELEV PLATEGASKETGASKETINSERTBALL SEATGLAND BOLTKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSNAP RINGSTOPPERSTEM BEARINGHANDLE BOLTHANDLE BOLTSPRING & PINSTOPPER PINSPACERA216 Gr. WCBA276 TYPE 316 or A479/A479M TYPE 316A276 TYPE 316 or A351 Gr. CF8MA276 TYPE 316 or A479/A479M TYPE 316 (SIZE 11/2 ONLY)A351 Gr. CF8 (SIZE 2 & OVER)150SCTAM (C)PTFE (SIZE 11/2 ONLY)150SCTAM (C)PTFE (SIZE 2 & OVER)150SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEEL (SIZE 11/2 ONLY)DUCTILE IRON (SIZE 2-4)CARBON STEEL (SIZE 6 & OVER)DUCTILE IRON (SIZE 6 & OVER)STAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEELSTAINLESS STEELPTFE150SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCB (SIZE 11/2, 2, 8, 10)A105N (SIZE 3-6)HYPATITE PTFEA193 Gr. B8M (SIZE 2 & OVER)STAINLESS STEELSTAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEEL (SIZE 11/2 ONLY)G/F PTFE (SIZE 11/2 & 2)CARBON STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 2 & OVER)G/F PTFE (SIZE 3 & OVER)STAINLESS STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 6 & OVER)STAINLESS STEELSTAINLESS STEEL150SCTAM-FS (C)REINFORCED PTFE (SIZE 11/2 ONLY)Materials Name of Parts No.MATERIAL LIST134778899910101616191929303640434347484967123123124126155ABABABABABABABABNominal SizeUnit : inch1.502.003.004.006.008.0010.00d1.181.502.283.004.495.677.36d1405080100150200250mm11/22346810in.5.005.207.768.399.6911.5413.62H7.099.0615.7515.7529.5339.3759.06D16.578910.511.513L5.006.007.509.0011.0013.5016.00D3.884.756.007.509.5011.7514.25C44488812No.0.620.750.750.750.880.881.00h1/25/85/85/83/43/47/8Bolt Size2.883.625.006.198.5010.6212.75g0.560.620.750.941.001.121.19t0.060.060.060.060.060.060.06f0.550.670.870.871.061.421.81A0.710.871.101.101.421.892.361.382.172.782.783.353.945.12B1.972.764.024.024.925.516.50E F0.510.670.870.871.061.421.81G1.261.341.771.771.972.483.07K0.080.080.080.080.080.080.08T1/4-20UNC5/16-18UNC3/8-16UNC3/8-16UNC1/2-13UNC5/8-11UNC3/4-10UNCUF05F07F10F10F12F14F16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONS019class 150 cast steel ball valves class 300 cast steel ball valves300SCTDZM300SCTDZM-FSNominal SizeUnit : inch0.550.750.951.501.972.523.003.945.957.95d15202540506580100150200mm1/23/4111/2221/23468in.4.254.374.885.285.637.057.448.8212.4015.98H5.125.127.099.069.0615.7515.7529.5339.3759.06D15.506.006.507.508.509.5011.1212.0015.8819.75L3.754.624.886.146.507.508.2510.0012.5015.00D2.623.253.504.505.005.886.627.8810.6213.00C444488881212No.0.620.750.750.880.750.880.880.880.881.00h1/25/85/83/45/83/43/43/43/47/8Bolt Size1.381.692.002.883.624.125.006.198.5010.62g0.560.620.690.810.881.001.121.251.441.62t0.060.060.060.060.060.060.060.060.060.06f0.360.360.550.670.670.870.871.061.421.81A0.470.470.710.870.871.101.101.421.892.360.990.991.382.172.172.762.763.353.945.12B1.421.421.972.762.764.024.024.925.516.50E F0.350.350.550.670.670.870.871.061.421.81G0.870.871.181.341.341.771.772.052.483.11K0.040.040.060.060.060.080.080.080.080.08TM5M5M6M8M8M10M10M12M16M20UF03F03F05F07F07F10F10F12F14F16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleBODYBODY CAPSTEMBALLGLANDGLAND PACKIINGHANDLEHANDLE BARHANDLE HEADNAME PLATELEV PLATEGASKETPACKING WASHERBALL SEATCAP NUTCAP BOLTGLAND BOLTKEYLOCK PLATEHANDLELOCK PLATESNAP RINGSTOPPERSTOPPER PLATEGLAND BUSHGLAND WASHERSTEM BEARINGHANDLELOCK PLATE BOLTHANDLE BOLTSPRING & PINSTOPPER PLATE BOLT CONED DISC SPRINGSCE PLATEATEX PLATEA216 Gr. WCBA216 Gr. WCBA276 TYPE316A276 TYPE316 or A351 Gr. CF8MA351 Gr. CF8300SCTDZM(C)PTFE300SCTDZM-FS(C)FLEXIBLE GRAPHITEDUCTILE IRON(UP TO SIZE 3)CARBON STEEL(SIZE 4 & OVER)DUCTILE IRON(SIZE 4 & OVER)A276 TYPE304A276 TYPE304300SCTDZM(C)PTFE300SCTDZM-FS(C)FLEXIBLE GRAPHITEA276 TYPE316L(UP TO SIZE 1)HYPATITE PTFEA194 Gr. 2HMA193 Gr. B7MSTAINLESS STEELA276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304A276 TYPE304G/F PTFEA276 TYPE304G/F PTFESTAINLESS STEELSTAINLESS STEELA313 & A276 TYPE316STAINLESS STEELInconel 718 or EquivalentA276 TYPE304(SIZE 11/2 & OVER)A276 TYPE304Materials Name of Parts No.MATERIAL LIST12347899916161920303335364043484951575867123123124126145216216ABABABABDIMENSIONS150SCTAM (C)150SCTAM-FS (C)BODYSTEMBALLGLANDGLANDGLAND PACKINGGLAND PACKINGHANDLEHANDLE BARHANDLE HEADHANDLE NUTNUTNAME PLATELEV PLATEGASKETGASKETINSERTBALL SEATGLAND BOLTKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSNAP RINGSTOPPERSTEM BEARINGHANDLE BOLTHANDLE BOLTSPRING & PINSTOPPER PINSPACERA216 Gr. WCBA276 TYPE 316 or A479/A479M TYPE 316A276 TYPE 316 or A351 Gr. CF8MA276 TYPE 316 or A479/A479M TYPE 316 (SIZE 11/2 ONLY)A351 Gr. CF8 (SIZE 2 & OVER)150SCTAM (C)PTFE (SIZE 11/2 ONLY)150SCTAM (C)PTFE (SIZE 2 & OVER)150SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEEL (SIZE 11/2 ONLY)DUCTILE IRON (SIZE 2-4)CARBON STEEL (SIZE 6 & OVER)DUCTILE IRON (SIZE 6 & OVER)STAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEELSTAINLESS STEELPTFE150SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCB (SIZE 11/2, 2, 8, 10)A105N (SIZE 3-6)HYPATITE PTFEA193 Gr. B8M (SIZE 2 & OVER)STAINLESS STEELSTAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEEL (SIZE 11/2 ONLY)G/F PTFE (SIZE 11/2 & 2)CARBON STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 2 & OVER)G/F PTFE (SIZE 3 & OVER)STAINLESS STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 6 & OVER)STAINLESS STEELSTAINLESS STEEL150SCTAM-FS (C)REINFORCED PTFE (SIZE 11/2 ONLY)Materials Name of Parts No.MATERIAL LIST134778899910101616191929303640434347484967123123124126155ABABABABABABABABNominal SizeUnit : inch1.502.003.004.006.008.0010.00d1.181.502.283.004.495.677.36d1405080100150200250mm11/22346810in.5.005.207.768.399.6911.5413.62H7.099.0615.7515.7529.5339.3759.06D16.578910.511.513L5.006.007.509.0011.0013.5016.00D3.884.756.007.509.5011.7514.25C44488812No.0.620.750.750.750.880.881.00h1/25/85/85/83/43/47/8Bolt Size2.883.625.006.198.5010.6212.75g0.560.620.750.941.001.121.19t0.060.060.060.060.060.060.06f0.550.670.870.871.061.421.81A0.710.871.101.101.421.892.361.382.172.782.783.353.945.12B1.972.764.024.024.925.516.50E F0.510.670.870.871.061.421.81G1.261.341.771.771.972.483.07K0.080.080.080.080.080.080.08T1/4-20UNC5/16-18UNC3/8-16UNC3/8-16UNC1/2-13UNC5/8-11UNC3/4-10UNCUF05F07F10F10F12F14F16ISO 5211Flange TypeEnd Flange Mounting Dimensions for ActuatorBolt HoleDIMENSIONS020300SCTAM (C)300SCTAM-FS (C)BODYSTEMBALLGLANDGLAND PACKINGHANDLEHANDLE NUTNUTNAME PLATEGASKETGASKETINSERTBALL SEATKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSTEM BEARINGRING SPRINGSTOPPER PINA216 Gr. WCBA276 TYPE 316A276 TYPE 316A276 TYPE 316300SCTAM (C)PTFE300SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELSTAINLESS STEELPTFE300SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCBHYPATITE PTFESTAINLESS STEELSTAINLESS STEELSTAINLESS STEELC/F PTFE (SIZE 1 ONLY)C/F PTFE (SIZE 1/2 & 3/4)STAINLESS STEELSTAINLESS STEELMaterials Name of Parts No.MATERIAL LIST134789101016191929304043434767124126ABABABBODYSTEMBALLGLANDGLANDGLAND PACKINGGLAND PACKINGHANDLEHANDLE BARHANDLE HEADHANDLE NUTNUTNAME PLATELEV PLATEGASKETGASKETINSERTBALL SEATGLAND BOLTKEY LOCK PLATEWASHERCONED DISC SPRINGSTHRUST WASHERSNAP RINGSTOPPERSTEM BEARINGHANDLE BOLTHANDLE BOLTSPRING & PINSTOPPER PINSPACERA216 Gr. WCBA276 TYPE 316 or A479/A479M TYPE 316A276 TYPE 316 or A351 Gr. CF8MA276 TYPE 316 or A479/A479M TYPE 316 (SIZE 11/2 ONLY)A351 Gr. CF8 (SIZE 2 & OVER)300SCTAM (C)PTFE (SIZE 11/2 ONLY)300SCTAM (C)PTFE (SIZE 2 & OVER)300SCTAM-FS (C)FLEXIBLE GRAPHITESTAINLESS STEEL (SIZE 11/2 ONLY)DUCTILE IRON (SIZE 2-4)CARBON STEEL (SIZE 6 & OVER)DUCTILE IRON (SIZE 6 & OVER)STAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEELSTAINLESS STEELSTAINLESS STEELPTFE300SCTAM-FS (C)FLEXIBLE GRAPHITEA216 Gr. WCB (SIZE 11/2, 2, 8, 10)A105N (SIZE 3-6)HYPATITE PTFEA193 Gr. B8M (SIZE 2 & OVER)STAINLESS STEELSTAINLESS STEEL (SIZE 11/2 ONLY)STAINLESS STEEL (SIZE 11/2 ONLY)G/F PTFE (SIZE 11/2 & 2)CARBON STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 2 & OVER)G/F PTFE (SIZE 3 & OVER)STAINLESS STEEL (SIZE 2 & OVER)STAINLESS STEEL (SIZE 6 & OVER)STAINLESS STEELSTAINLESS STEEL300SCTAM-FS (C)REINFORCED PTFE (SIZE 11/2 ONLY)Materials Name of Parts No.MATERIAL LIST134778899910101616191929303640434347484967123123124126155ABABABABABABABABNominal SizeUnit : inch0.490.750.98d0.390.490.67d1152025mm1/23/41in.3.503.583.94H5.525.526.30D15.506.006.50L3.754.624.88D2.623.253.50C444No.0.620.750.75h1/25/85/8Bolt Size1.381.692.00g0.560.620.69t0.060.060.06f0.280.280.36A0.390.390.470.990.990.99B1.421.421.42E F0.290.290.37G0.650.650.85K0.060.060.06T1/4-20UNC1/4-20UNC1/4-20UNCUF03(2)F03(2)F03ISO 5211Flange Typeclass 300 cast steel ball valves class 300 cast steel ball valves300SCTAM (C)300SCTAM-FS (C)NOTE(1) All valves have an anti-static thrust washer or stem bearing insuring positive conductivity between body and stem.(2) Dimensions A and B are in accordance with CAPI F03-S.End Flange Mounting Dimensions for ActuatorBolt HoleNominal SizeUnit : inch1.502.003.004.006.008.0010.00d1.181.502.283.004.495.677.36d1405080100150200250mm11/22346810in.5.005.207.768.399.6911.5413.62H7.099.0615.7515.7529.5339.3759.06D17.508.5011.1312.0015.8816.5018.00L6.126.508.2510.0012.5015.0017.50D4.505.006.627.8810.6213.0015.25C4888121216No.0.880.750.880.880.881.001.12h3/45/83/43/43/47/81Bolt Size2.883.625.006.198.5010.6212.75g0.810.881.121.251.441.621.88t0.060.060.060.060.060.060.06f0.550.670.870.871.061.421.81A0.710.871.101.101.421.892.361.382.172.7