introduction to räder-vogel® wheels - · pdf fileintroduction to...

Introduction to RÄDER-VOGEL® Wheels

Acorn Industrial Products Co l 800.523.5474 l www.acornindprod.com 11.117

11

RÄDER-VOGEL® WHEEL PRODUCTION FACILITYBAYER® has been manufacturing Urethane production equipment since 1946 and provides assistance in the productionand testing of VULKOLLAN® and Premium Urethane wheels toassure consistent quality performance.

BAYER® assures the end user the right chemical compositionand pouring temperature of the Urethanes and VULKOLLAN® to achieve the proper quality and durometer required.

RÄDER-VOGEL® has been producing VULKOLLAN® and premium urethanes since 1946 and has the most modern automated urethane production facility in the world.


11 .118 Acorn Industrial Products Co l 800.523.5474 l www.acornindprod.com

11

RÄDER-VOGEL® WHEEL PRODUCTION FACILITY



11

TRACTOTHAN® / VULKOLLAN®VULKOLLAN® tread material is expensive, but its specific properties – except traction – makes it the best read material forwheels having to meet the highest standards concerning speed,load capacity, resilience, resistance to abrasion, etc.

TRACTOTHAN® is a material developed by RÄDER-VOGEL®with all the same outstanding properties as VULKOLLAN®, butin addition it has far better traction due to a higher coefficient offriction. TRACTOTHAN® is produced in a special patented production process. Special polyurethane granules, having alower shore hardness are integrated into the entireVULKOLLAN® tread, which increases the road grip and lowersthe risk of sliding.

TRACTOTHAN® improves starting properties, reduces slip, increases the braking effect and is therefore best suited for universal use due to the improved in-plant operating safety.

Many plant floors are becoming more slippery, due to variousnew types and coatings. Operating on dry, as well as wet anddirty floors during in-plant transportation or in damp and wetenvironments such as cold storage rooms, slaughter houses,wheels with TRACTOTHAN® (above 5 mph) are definitely thebest alternative for improved plant operating safety. Below 5mph, TRACTOPUR® wheels may be a lower cost alternative. (See TRACTOPUR® in the Urethane section.)

Leading industrial truck and gear motor manufacturers arechanging to TRACTOTHAN® in their drive wheels for speedsabove 5 mph. Call us to discuss any application.

TRACTOTHAN® wheels are used for in-plant transportation on fine,smooth as well as wet and dirty floors. The stopping distance isreduced and therefore plant safety is increased.

VULKOLLAN® Wheels are available for any size caster and hublength.

VULKOLLAN® and TRACTOTHAN® are available from 85 to 93Shore A durometer.



11

VULKOLLAN® 93 SHORE A / TRACTOTHAN® 93 SHORE AVULKOLLAN® and TRACTOTHAN® ISO Specifications are available for 85 to 93 Shore A Durometers.

Mechanical Features VULKOLLAN® 93 Shore A TRACTOTHAN® 93 Shore AShore Hardness A DIN 53 505 93 93 PU-Inclusions

Density in g/cm3 DIN 53 479 1.26 1.25

Elongation at rupture in % DIN 53 504 Approx. 600 Approx. 600

Tensile stress in MPa at 100% DIN 53 504 9 – 9.5 9 – 9.5

Modulus of elasticity in MPa at 20 C DIN 53 457 80 – 90 80 – 90

Impact resilience in % DIN 53 512 55 – 60 55 – 60

Resistance to tear propagation in kN DIN 53 515 55 – 60 55 – 60

Compression set in % 70 h. 23 C DIN 53 517 10 – 11 10 – 11

Abrasion loss in mm3 DIN 63 516 39 40

Coefficient of friction (traction) on wet floor at 8000 N 0.10 0.15

Rolling resistance at 20 C in % of charge (average) 0.8 – 0.9 0.9 – 1.0

Starting resistance at 20 C in % of charge 1.1 – 1.4 1.2 – 1.5

VULKOLLAN® and TRACTOTHAN® are registered trademarks.All values indicated in this table are approximative values resulting from our own tests or information given by our raw material suppliers. The normed values refer to special test samples, so that these values are not directly applicable for wheels and casters.Furthermore, these values change under such influences as temperature, humidity, duration of charge compression, etc.



11VU

LKOLLAN

® / TR

ACTO

THAN

® / PE

VOPU

R® / PE

VOTH

AN®

Complete technical specifications are availa

ble for all w

heels.

VULKOLLAN® Wheels


11

Rollers and wheels are major application areas for VULKOLLAN®,since they exposed to many stresses. The behavior of the materialVULKOLLAN® under dynamic stress can be determined on aroller test bed. The advantage over other dynamic tests is that finished parts, can be tested under conditions similar to those encountered in practice.

VULKOLLAN’s® special combination of properties has alreadybeen verified by various institutions, including the TechnicalInspection Authorities in Munich and the Materials HandlingInstitute at the Technical University of Berlin and by many AGVand vehicle manufacturers. The outstanding load-bearing capacityof VULKOLLAN® rollers has been confirmed in all areas.

While testing the elastomer on the roller test bed, the quality ofthe VULKOLLAN® bond to the metal core and information aboutthe optimum cross section can also be obtained.

Call toll-free to make use of our extensive experience of

VULKOLLAN® applications: 800-523-5474

RÄDER-VOGEL®


11

VULKOLLAN® and TRACTOTHAN®VULKOLLAN® is the best of the urethane wheels (600%plus elongation to rupture) with dual sealed, pre-loaded precision ball bearings for heavy duty and speeds above 8 mph.

For use in heavy duty casters, AGV’s, power towing, lifttrucks, pallet trucks, trollies, press-ons, drive wheels.

RÄDER-VOGEL® produces Vulkollan™ for moving and driving loads up to 10 tons (20,000 lbs) and more. Wheeldiameters up to 920 mm (36.22 ins.)

Made the Hot-Cast WayAny size or shape to print or for use in any series casterrig or application.

Vulkollan® Is Ideal For: Drive wheels and high speed applications.

VULKOLLAN® Properties


11

SHORE HARDNESS

Shore Hardness is determined by testing the indentation resistance. Theindentation resistance with which theelastomer opposes a spring-mountedneedle is measured and displayed on ascale of 0 to 100. Shore A testing isused for softer elastomers. The Shore D scale is preferred from about 90Shore A.

ULTIMATE TENSILE STRENGTH

Tensile Stress is measured on speciallyshaped test bars in tensile testingmachines and is indicated as a functionof the strain. Testing is normally at100%, 300% and a breakage.VULKOLLAN® displays very highstrength values. The test bars only tearafter elongation to over 7 times theoriginal length. Tensile strength testingis frequently used for quality control.

TEAR PROPOGATION RESISTANCE

Tear propogation resistance is measured by stretching a notched specimen. High tear propogation resistance values denote reliable performance even of damaged parts.

ABRASION

Abrasion is measured by various methods, normally according to ISO 4649(“abrasion roll”) and ISO 9352 (“Taber”).The elastomer specimens are rubbed withdefined grinding media and abrasion isdetermined by loss of weight or volume.Low abrasion values denote high resist-ance to wear.

COMPRESSION DEFORMATION

The residual deformation after sustainedcompressive deformation is measured bydetermining the compression set. The teststoppers are deformed to a specific extentat defined temperatures and for definedtemperatures and for defined periods.Recovery is then determined. Low valuesdenote low permanent set.

REBOUND RESILIENCE

Rebound resilience is measured with afalling hammer. The higher the rebound,the less energy is absorbed in the elastomer and converted into heat.

RÄDER-VOGEL® Wheels - Index


11

PALLET ROLLERS& PRESS-ON TIRES

VULKOLLAN® WHEELS VULKOLLAN® /CAST IRON CORE

PEVOSOFT®ALUMINUM CORE

PEVOPUR®ALUMINUM CORE

PEVOSOFT®CAST IRON CORE

PEVOPUR®CAST IRON CORE

PE•VO•LON® PEVOLASTIC® PEVOTHAN®

DRIVE WHEELS GUIDE ROLLERS& GUIDE WHEELS

RÄDER-VOGEL® WHEELS PAGE #

VULKOLLAN® ....................................125-130

PEVOSOFT® & PEVOPUR® ..............131-136

PE•VO•LON® .....................................137-139

PEVOLASTIC® / PEVOTHAN® ..........140-143

Drive Wheels ......................................144-146

Guide Rollers .....................................147-149

Pallet Rollers ......................................150-153

Press-On Tires ....................................154-158

Visit our Web site for new products

www.acornindprod.com

RÄDER-VOGEL® - VULKOLLAN®


11

VULKOLLAN®Rubbery-Elastic VULKOLLAN® in its classic form is apolyurethane elastomer based on naphthalane 1,5-disocyanate(Desmodur™ 15), polyester polyol and special chain extenders. VULKOLLAN® is produced by hot casting.

The raw materials used for VULKOLLAN® are subject to tight specifications and strict quality controls. All licensed processors must follow BAYER’S® guidelines forVULKOLLAN® formulations and production processes, otherwise they cannot use the name VULKOLLAN®.

Required guidelines are covered by a trademark agreementbetween BAYER® and RÄDER-VOGEL® and are essential for the production of consistently high quality elastomers.

Some USA wheel producers claim a material equal toVULKOLLAN®; but if they are not licensed by BAYER®,it is not the same.

VULKOLLAN® wheels take up to 4 weeks to produce, due tothe stabilizing requirements needed. Thus it is important toallow adequate time for any application.

Both RÄDER-VOGEL® and Acorn™ stock many of theVULKOLLAN® wheels and are continuously increasing stock for JIT deliveries to OEM, AGV, Automotive and IndustrialCustomers.

VULKOLLAN® – the best of the Urethanes – is designed to

take heavy loads, under demanding conditions, and a must

for speeds above 5 mph.

Stated loads shown are for operation under ideal conditions, i.e. the wheel operates infrequently on a smooth surface without axial loading.

Thus load ratings must be reduced for operation under any

or all of the following conditions:

• Frequent use in excess of 45 minutes continuous:

reduce loadings by 25%• Driving applications:

reduce loadings by 30%• Speeds 6-10 kph ( 3.73 - 6.21 mph ):

reduce loads by 20%• Speeds10-16 kph ( 6.21 - 10 mph ):

reduce loadings by 30%

It is important to note that the above reduction in ratings are cumulative if more than one of the conditions exists.

Please contact our application department for advice if thewheels are subject to high humidity, speeds in excess of 16kph (10 mph), exposure to chemicals, steering or running on a curved surface.

RÄDER-VOGEL® - VULKOLLAN® / Cast Iron Core


11

25.4 mm = 1 inch1 kg = 2.2 lbs

Grey cast iron center with ball bearings (/5). Directbonded VULKOLLAN® tread.

Series 178 withPrecision Bearings

Series 178 – VULKOLLAN® Load Wheels A highly elastic cross-linked polyurethane elastomer produced on the basis of Desmodur® 15 of BAYER® AG. Among the excellentmechanical characteristics of VULKOLLAN® are: high dynamic load capacity, higher abrasion and tear propagation resistance thanmost other materials; the highest modulus of elasticity of all elastomers; good mechanical wear resistance and impact resilience as well as a low compression set. Furthermore, VULKOLLAN® offers good chemical resistance to mineral oils and greases and different solvents. It is specially recommended for high requirements regarding load capacity, rebound resilience, speed and durability.Therefore, VULKOLLAN® is preferred for drive wheels for industrial trucks, in material handling and mechanical engineering.



11

Series 178 A – VULKOLLAN® drive wheels

Grey cast iron wheel center with bore and keyway accord-ing to DIN 6885. Direct bonded VULKOLLAN® tread.

Series 171 A - VULKOLLAN® drive wheels

As above, but with welded steel wheel center.

25.4 mm = 1 inch 1 kg = 2.2 lbs

Options: TRACTOTHAN® is available in both VUI 178/5 and VU 178A Series: Add AT after ordering number (i.e. VUI 178/100/50/5/25/AT)

Series 178 A – VULKOLLAN® Drive Wheels

Series 171 A – VULKOLLAN® Drive Wheels



11

Standard sizes with Preloaded Precision Bearings / Ratings to 5500 lbs

VULKOLLAN® tired heavy duty wheels with grey cast iron

core have better properties than Urethane or Elastic Rubber.

• Highest wear resistance• Highest abrasion and tear resistance• Longer service life (up to 10 times that of rubber)• Dynamic load capacity 2.5 times that of rubber (of same dimensions)

For speeds greater than 5 mph (8 kph), VULKOLLAN® treads

should be used.

VULKOLLAN® wheels are available for any size caster and

hub length

TREAD:VULKOLLAN® properly bonded to the wheel core. Hardness 93Shore A.

WHEEL CORE:Special grey cast iron with pre-loaded precision ball bearings.

Series VUI 178 withPrecision Bearings

Item # Diameter Tread Width Wheel Hub / Length Bearing ID Load Capacity(mm) (mm) (mm) (mm) (lbs)

VUI 178/100/025/5/15 100 25 26/26 15 440

VUI 178/100/035/5/12 100 35 40/40 12 660

VUI 178/100/040/5/15 100 40 42/45 15 770

VUI 178/100/040/5/15-B 100 40 42/45 15 770

VUI 178/100/050/5/20-B 100 50 54/50 20 990

VUI 178/125/030/5/15 125 30 29/30 15 660

VUI 178/125/040/5/15 125 40 45/45 15 880

VUI 178/125/050/5/20 125 50 54/50 20 1232

VUI 178/125/050/5/25 125 50 54/50 25 1232

VUI 178/140/060/5/20-B 140 60 68/68 20 1650

VUI 178/150/035/5/25 150 35 39/35 25 880

VUI 178/150/050/5/20 150 50 54/50 20 1452

VUI 178/150/050/5/25 150 50 54/50 25 1452

VUI 178/150/060/5/20 150 60 60/60 20 1760

VUI 178/160/040/5/20 160 40 49/45 20 1144

VUI 178/160/050/5/20 160 50 60/60 20 1540

VUI 178/200/050/5/20 200 50 64/60 20 2200

VUI 178/200/050/5/25 200 50 64/60 25 2200

VUI 178/200/080/5/25 200 80 84/80 25 2970

VUI 178/250/050/5/25 250 50 64/60 25 2420

VUI 178/250/060/5/25 250 60 60/60 25 2970

VUI 178/250/080/5/30 250 80 80/80 30 3740

VUI 178/300/060/5/30 300 60 65/65 30 3520

VUI 178/300/080/5/40 300 80 100/100 40 4840

VUI 178/300/100/5/40 300 100 120/120 40 5500

RÄDER-VOGEL® - VULKOLLAN® / Steel Core


VUS 171/300/050/5/30 300 50 55 30 2530

VUS 171/300/075/5/35 300 75 80 35 3740

VUS 171/300/100/5/35 300 100 110 35 4840

VUS 171/360/060/5/30 360 60 65 30 3520

VUS 171/360/075/5/40 360 75 80 40 4400

VUS 171/360/100/5/40 360 100 110 40 5500

VUS 171/400/100/5/40 400 100 110 40 6160

VUS 171/400/120/5/50 400 120 130 50 7480

VUS 171/400/150/5/50 400 150 160 50 9460

VUS 171/500/075/5/50 500 75 80 50 5500

VUS 171/500/100/5/50 500 100 110 50 7480

VUS 171/500/120/5/50 500 120 130 50 8800

VUS 171/500/150/5/50 500 150 160 50 11000

VUS 171/500/200/5/80 500 200 210 80 14740

VUS 171/600/150/5/80 600 150 160 80 13860

VUS 171/600/200/5/80 600 200 210 80 18480


11

Standard sizes with Preloaded Precision Bearings / Ratings to 18,400 lbs

VULKOLLAN® Tread – Steel Double Welded Core with Pre-Loaded Precision Bearings

VULKOLLAN® tired heavy duty wheels with grey cast iron core

have better properties than Urethane or Elastic Rubber.



should be used.


hub length

TREAD:VULKOLLAN® properly bonded to the steel core.Hardness 93 Shore A. (other harnesses available)

WHEEL CORE:Strong steel welded construction with tow foldwelded tubular steel core.

Series VUS 171with Precision

Bearings

RÄDER-VOGEL® - VULKOLLAN® / Steel Core


11

Series 171 / 5 VULKOLLAN® heavy duty wheels

Stable welded wheel center withball bearings (/5). Direct bonded VULKOLLAN® tread.

Standard VULKOLLAN® Wheels are made with a hardness of 93 Shore A. However, due to flexibility in production, otherdegrees of hardness are available (e.g. 85 Shore A with better damping noise reduction and treating the floor with careas well as harder qualities. A hardness of 95 Shore A is available for extreme dynamic applications.

RÄDER-VOGEL® - PEVOSOFT® & PEVOPUR® / AL Core


11

Series 183 ALU/PUR PEVOSOFT® wheels 75º ShoreA with aluminum rim

Aluminum wheel center with ballbearings (/5). Direct bondedPEVOSOFT® tread 75º Shore A.

Series 181 PUR PEVOPUR® wheels with aluminum rim

Aluminum wheel center with ballbearings (/5). Direct bondedPEVOPUR® tread.

PEVOPUR® is a high quality polyurethane elastomer. It is, like VULKOLLAN®, produced with a hot casting method and, contrary to so-called cold cast systems, subjected to a subsequent heat treatment. Among its outstanding mechanical and chemical characteristics count dynamic load capacity, high elasticity, good compression set and resistance to a multitude of chemical media.Compared to rubber, the load capacity of PEVOPUR® is many times higher. Moreover, it is non-marking. PEVOPUR® is particularly suitable for applications with a lower requirement profile, e.g. manually operated transport equipment (up to 6 km/h).

PEVOPUR® is specially used for pedestrian-controlled trucks. Our extensive delivery program includes drive and load wheels as well as pallet rollers and stabilizing casters for almost al pedestrian controlled trucks and battery-powered models of all industrial truckmanufacturers.

RÄDER-VOGEL® - PEVOPUR® / Cast Iron Core


11

PEVOPUR® / CAST IRON CORE178 PURwith Ball Bearings

Compared to rubber, PEVOPUR® (Urethane 93A) as a tread forpress-on tires, heavy-duty wheels and casters is characterized bya longevity which is several times higher, a higher dynamic loadcapacity as well as a lower rolling resistance. Diverse caster systems are available with a load capacity of up to 4,000 kg forin-plant transportation. Our range of products includes pressedsteel brackets as well as welded steel swivel and fixed brackets.Locking systems (ALLSTOP, directional lock) are available asstandard products for all swivel brackets.

PEVOPUR® (Urethane 93A) is processed with a shore hardnessof 93 Shore A for standard products. However, due to flexibilityin production, other degrees of hardness are available (e.g. 75Shore A for better noise reduction and with floor saving properties.

RÄDER-VOGEL® - PEVOPUR® / Cast Iron Core


11

PEVOPUR® (Urethane 93A) is a high quality polyurethane elastomer bonded to a cast iron, aluminum or steel core havinggood chemical and physical properties and well tested for speedsup to 6 kph (3.73 mph).

Urethane is highly elastic,the compression set quality and thedynamic load capacity are very good but not to the same extent as VULKOLLAN®, TRACTOTHAN®, or TRACTOPUR®.

Compared with rubber of the same dimensions, PEVOPUR® hasmuch longer durability,has much higher load capacity and is non-marking.

Features• Hardness - 93 Shore A• Resilient• Abrasive resistant• High cut resistant and resistance to tearing• Non-marking• Floor protective• Low noise• Low rolling resistance

All wheels can be matched with end caps to fit in

U.S. caster rigs.

PEVOPUR® / CAST IRON CORE178 PURwith Precision Bearings

Dia. Width Hub Length Bore Bearing ID Capacity Wheel(mm) (mm) (in.) (mm) (mm) (lb) Part Number

100 25 20/26 42 15 440 178 PUR/100/035/5/12100 35 40/40 43 12 660 178 PUR/100/025/5/15100 40 42/45 45 15 770 178 PUR/100/040/5/15100 40 42/45 45 15 770 178 PUR/100/040/5/15100 50 54/50 70 20 990 178 PUR/100/050/5/20

125 30 29/30 45 15 660 178 PUR/125/030/5/15125 40 45/45 50 15 880 178 PUR/125/040/5/15125 50 54/50 60 20 1230 178 PUR/125/050/5/20125 50 54/50 60 25 1230 178 PUR/125/050/5/25

140 60 68/68 68 20 1650 178 PUR/140/060/5/20

150 35 39/35 61 25 880 178 PUR/150/035/5/25150 50 54/50 60 20 1450 178 PUR/150/050/5/20150 50 54/50 60 25 1450 178 PUR/150/050/5/25150 60 60/60 75 20 1760 178 PUR/150/060/5/20

160 40 45/45 64 20 1140 178 PUR/160/040/5/20160 50 60/60 65 20 1540 178 PUR/160/050/5/20

200 50 64/60 65 20 2200 178 PUR/200/050/5/20200 50 64/60 67 25 2200 178 PUR/200/050/5/25200 80 84/80 70 25 2970 178 PUR/200/080/5/25

250 50 64/60 67 25 2200 178 PUR/250/050/5/25250 60 60/60 75 25 2970 178 PUR/250/060/5/25250 80 80/80 75 30 3740 178 PUR/250/080/5/30

300 60 65/65 80 30 3520 178 PUR/300/060/5/30300 80 100/100 105 40 4840 178 PUR/300/080/5/40300 100 120/120 105 40 5500 178 PUR/300/100/5/45

25.4 mm = 1 in.

RÄDER-VOGEL® - PEVOPUR® / Aluminum Core


11

Features• Hardness - 93 Shore A• Resilient• Abrasive resistant• High cut resistant and resistanceto tearing• Non-marking• Floor protective• Low noise• Low rolling resistance

All wheels can be matched with

end caps to fit in U.S. caster rigs.

PEVOPUR® (Urethane 93A) is a high quality polyurethane elastomer bonded to a cast iron, aluminum or steel core havinggood chemical and physical properties and well tested for speedsup to 6 kph (3.73 mph).

Urethane is highly elastic,the compression set quality and thedynamic load capacity are very good but not to the same extent as VULKOLLAN®, TRACTOTHAN®, or TRACTOPUR®.

Compared with rubber of the same dimensions, PEVOPUR® hasmuch longer durability,has much higher load capacity and is non-marking.

PEVOPUR® /ALUMINUM CORE181 PURwith Precision Bearings


80 25 35 40 15 330 181 PUR/080/25/5/15100 40 45 46 15 550 181 PUR/100/40/5/15125 50 59 64 20 880 181 PUR/125/50/5/20150 50 59 64 20 990 181 PUR/150/50/5/20160 50 59 64 20 1100 181 PUR/160/50/5/20180 50 59 64 20 1210 181 PUR/180/50/5/20200 80 59 64 20 1540 181 PUR/200/50/5/20200 80 59 64 25 1540 181 PUR/200/50/5/25

25.4 mm = 1 in. Refer to page 132 for weights in kg

RÄDER-VOGEL® - PEVOSOFT® / Cast Iron Core


11

PEVOSOFT® /CAST IRON CORE183 PURwith Precision Bearings

PEVOSOFT® (Urethane 75A) is a high quality polyurethane elastomer bonded to a cast iron, aluminum or steel core having good chemical and physical properties and well tested for speeds up to 6 kph (3.73 mph).

Urethane 75A is highly elastic,the compression set quality and thedynamic load capacity are very good but not to the same extent asVULKOLLAN®.

Urethane 75A is formulated for a quieter operation and less resistance to foreign objects and floor debris. It reduces vibration inthe wheel resulting in a quieter ride with less wear on the caster andload. In addition it repels floor chips, bolts, pins, metal scraps etc.from imbedding in the tread.

All wheels can be matched with end caps to fit in U.S. caster rigs.

Urethane 75A has been a proven success for automotive plants andthose wanting to lower noise levels, improve floor protection andreduce tread failures.

Urethane 75A has all the soft qualities of rubber with much better life,higher load carrying ability and is non-marking.


125 50 60 64 20 775 183 PUR/125/050/5/20150 50 60 59 20 990 183 PUR/150/050/5/20200 50 60 67 20 1430 183 PUR/200/050/5/20250 50 60 67 25 1650 183 PUR/250/050/5/25250 80 85 70 25 2090 183 PUR/250/080/5/25300 80 85 80 30 2640 183 PUR/300/080/5/30

25.4 mm = 1 in.

Features• Hardness: 75 Shore A• Resilient• Abrasive resistant• High cut resistant and resistanceto tearing• Non-marking• Floor protective• Low noise• Low rolling resistance

RÄDER-VOGEL® - PEVOSOFT® / Aluminum Core


11

PEVOSOFT® /ALUMINUM CORE183 ALU/PURwith Precision Bearings


100 40 45 46 15 450 183 ALU/PUR/100/040/5/15125 50 59 55 20 700 183 ALU/PUR/125/050/5/20150 50 59 55 20 800 183 ALU/PUR/150/050/5/20160 50 59 55 20 900 183 ALU/PUR/160/050/5/20180 80 59 55 20 1000 183 ALU/PUR/180/040/5/20200 80 60 55 20 1100 183 ALU/PUR/200/050/5/20200 80 60 55 25 1100 183 ALU/PUR/200/050/5/25250 60 60 60 20 1700 183 ALU/PUR/250/060/5/20250 60 60 60 25 1700 183 ALU/PUR/250/060/5/25

25.4 mm = 1 in.

Urethane 75A is a high quality polyurethane elastomer bonded to a cast iron, aluminum or steel core having good chemical and physical properties and well tested for speeds up to 6 kph (3.73 mph).

Urethane 75A is highly elastic,the compression set quality and the dynamicload capacity are very good but not to the same extent as VULKOLLAN®.

Urethane 75A is formulated for a quieter operation and less resistance toforeign objects and floor debris. It reduces vibration in the wheel resulting in a quieter ride with less wear on the caster and load. In addition it repels floor chips, bolts, pins, metal scraps etc. from imbedding in the tread.

All wheels can be matched with end caps to fit in U.S. caster rigs.

Urethane 75A has been a proven success for automotive plants and thosewanting to lower noise levels, improve floor protection and reduce treadfailures.

Urethane 75A has all the soft qualities of rubber with much better life,higher load carrying ability and is non-marking.

Features• Hardness: 75A Shore A• Resilient• Abrasive resistant• High cut resistant and resistanceto tearing• Non-marking• Floor protective• Low noise• Low rolling resistance

RÄDER-VOGEL® - PE•VO•LON®


11

*Bore can be modified to any dimension (i.e. 1/2”, 3/4” etc.).Nylon (PE•VO•LON®) Wheels are available in Electrically Conductive Nylon. Add prefix“EC” to part number.

ALL PE•VO•LON® WHEELS ARE AVAILABLE WITH STANDARD OR STAINLESS STEELPRECISION BALL BEARINGS.

1 kg = 2.2 lbs1 inch = 25.4 mm



11

*Precision Bearings can be stainless steel.

1 kg = 2.2 lbs1 inch = 25.4 mm



11

PE•VO•LON® WheelsHigh quality thermoplastic polyamide. Light duty designwith maintenance free plain (/1) or roller bearing (/3)

Heat-Resistant WheelsWheels made of phenolic resin with plain bearing (/1).Heat resistant up to 230ºC.

Temperature range 180ºC (356ºF) continuous to 230ºC (446ºF) intermittentSpecial Nylamide

1 kg = 2.2 lbs1 inch = 25.4 mm

Nylon (PE•VO•LON®) Wheels are available in Electrically Conductive Nylon. Add prefix “EC” to part number.

RÄDER-VOGEL® - PEVOLASTIC® / PEVOTHAN®


11

PEVOLASTIC® and PEVOTHAN® are tow high quality thermoplastic polyurethane (TPU) elastomers. They have excellentproperties for wheels, e.g. high load capacity, high abrasion resistance, good damping and they leave no floor markings.

Series BPU

Series APU

Series 87PU

125-800 kg

60-1100 kg

110-400 kg

1 kg = 2.2 lbs1 inch = 25.4 mm

Series 89PU

100-400 kg

RÄDER-VOGEL® - PEVOLASTIC®


11

PEVOLASTIC® is a high quality thermoplastic polyurethane (TPU) elastomer with excellent properties for wheels, e.g. high load capacity, high abrasion resistance and non-marking.

Series BPU

Series APU

1 kg = 2.2 lbs1 inch = 25.4 mm

RÄDER-VOGEL® - PEVOTHAN®


11

Series 87 PU/1

Series 87 PU/5

PEVOTHAN® is a high quality thermoplastic polyurethane (TPU) elastomer with excellent properties for wheels, e.g. high load capacity, high abrasion resistance and non-marking.

1 kg = 2.2 lbs1 inch = 25.4 mm

RÄDER-VOGEL® - PEVOTHAN®


11

Series 89 PU/1

Series 89 PU/3

PEVOTHAN® is a high quality thermoplastic polyurethane (TPU) elastomer with excellent properties for wheels, e.g. highload capacity, high abrasion resistance and non-marking.

1 kg = 2.2 lbs1 inch = 25.4 mm

RÄDER-VOGEL® - VULKOLLAN® Drive Wheel / Steel Core


11

Standard sizes with Keyways / Ratings to 21,560 lbs

VULKOLLAN® Tread – Steel Double Welded Core with Keyway

25.4 mm = 1 inch 1 kg = 2.2 lbs

VULKOLLAN® tired heavy duty wheels with steel core have

better properties than Urethane or Elastic Rubber.



should be used.


hub length

TREAD:VULKOLLAN® properly bonded to the steel core.Hardness 93 Shore A. (other harnesses available)

WHEEL CORE:Strong steel welded construction with tow foldwelded tubular steel core.


VUI 178A/100/50/2/25 100 50 50 25 1070

VUI 178A/125/50/2/35 125 50 50 35 1540

VUI 178A/150/50/2/35 150 50 50 35 1540

VUI 178A/160/50/2/35 160 50 50 35 1140

VUI 178A/180/55/2/35 180 55 60 35 2200

VUI 178A/200/50/2/35 200 50 60 35 2200

VUI 178A/200/80/2/50 200 80 80 50 2640

VUI 178A/250/50/2/50 250 50 60 50 2420

VUI 178A/250/80/2/50 250 80 80 50 3740

VUI 178A/300/60/2/50 300 60 65 50 3520

RÄDER-VOGEL® - VULKOLLAN® Drive Wheel / CI Core


11

Standard sizes with Keyways / Ratings to 3520 lbsVULKOLLAN® tired heavy duty wheels with grey cast iron core have betterproperties than Urethane or Elastic Rubber.


VULKOLLAN® treads should be used fpr speeds greater than 5 mph (8kph), VULKOLLAN® treads should be used.

VULKOLLAN® Wheels are available for any size caster and hub length

TRACTOTHAN® is available in both VUI 178/5 and VU 178A Series: Add“AT” after ordering number (i.e. VUI 178/100/50/5/25/AT)


VUI 178A/100/50/2/25 100 50 50 25 1070

VUI 178A/125/50/2/35 125 50 50 35 1540

VUI 178A/150/50/2/35 150 50 50 35 1540

VUI 178A/160/50/2/35 160 50 50 35 1140

VUI 178A/180/55/2/35 180 55 60 35 2200

VUI 178A/200/50/2/35 200 50 60 35 2200

VUI 178A/200/80/2/50 200 80 80 50 2640

VUI 178A/250/50/2/50 250 50 60 50 2420

VUI 178A/250/80/2/50 250 80 80 50 3740

VUI 178A/300/60/2/50 300 60 65 50 3520

RÄDER-VOGEL® - VULKOLLAN® Drive Wheel / Steel Core


11

Series 171 / LVULKOLLAN® heavy dutywheels with bolt hole fitting

Stable welded wheel center withbolt hole fitting. Direct bonded VULKOLLAN® tread.

RÄDER-VOGEL® - VULKOLLAN® Guide Rollers


11

Series 173

RÄDER-VOGEL® - PE•VO•LON®Guide Rollers


11

Series 130 PA

Series 131 PA

Series 132 PA

Roller body made of high-quality thermoplastic polyamide moldedaround the precision ball bearing (/5).

PE•VO•LON® conveyor rollers withsealed precision bearings

Roller body made of high-quality thermoplastic polyamide moldedaround the ball bearing (/5).

PE•VO•LON® single flanged rollerswith prec. bearing

Roller body made of high-quality thermoplastic polyamide moldedaround the ball bearing (/5).

PE•VO•LON® grooved wheels withprec. bearing

RÄDER-VOGEL® - PEVOTHAN® Guide Wheels


11

Series 130 PU

Series 131 PU

Series 133 PU

Roller body made of high-quality thermoplastic polyurethane (96º shoreA) molded around the precision ball bearing (/5).

PEVOTHAN® conveyor rollers withprec. bearings

Roller body made of high-quality thermoplastic polyurethane (96º shoreA) molded around the ball bearing (/5).

PEVOTHAN® single flanged rollerswith prec. bearing

PE•VO•LON® roller body with a non-detachable, mechanically bondedtread made of high quality thermoplastic polyurethane (96ºshore A)molded around the ball bearing (/5).

PEVOLASTIC® conveyor rollers withprec. bearings

RÄDER-VOGEL® - VULKOLLAN® Pallet Rollers


11

RÄDER-VOGEL® - PEVOPUR® Pallet Rollers


11

PEVOPUR®

RÄDER-VOGEL® - VULKOLLAN® Press-On Tires


11



11

RÄDER-VOGEL® - PEVOPUR® Press-On Tires

PEVOPUR®

11


introduction to räder-vogel® wheels - · pdf fileintroduction to...

Documents