infant cpap patient interface - rt connection · bc480-sk* 3 2221 121 bc481-sk* 3 2221 121...

Infant CPAP Patient InterfaceInfant CPAP Patient Interface

u Presentation

u Setup Poster

u Animated Setup

u Ordering Information

u Product Specifications

INTERNATIONAL P O Box 14 348, Panmure, Auckland 1134, New Zealand Tel:+64 9 574 0100 Fax:+64 9 574 0158 Email: [email protected] Web Site: www.fphcare.comUSA Tel: 1800 446 3908 or +1 949 470 3900 Fax:+1 949 470 3933 AUSTRALIA Tel:+61 3 9879 5022 Fax:+61 3 9879 5232 AUSTRIA Tel: 0800 29 31 23 Fax: 0800 29 31 22 BENELUX Tel:+31 78 644 0924 Fax +31 78 644 0914 CHINA Tel:+86 20 8363 4286 Fax:+86 20 8363 3595 FRANCE Tel:+33 1 6446 5201 Fax:+33 1 6446 5221 GERMANY Tel:+49 7182 93777 0 Fax:+49 7182 93777 99 INDIA Tel:+91 80 51236041 Fax:+91-80-51236044 IRISH REPUBLIC Tel: 1800 409 011 ITALY Tel:+39 06 7839 2939 Fax:+39 06 7814 7709 JAPAN Tel:+81 3 3661 7205 Fax:+81 3 3661 7206 SPAIN Tel:+34 902 013 346 Fax:+34 902 013 379 UK (EU Authorised Representative) Tel:+44 1628 626 136 Fax:+44 1628 626 146 Nthn Ireland Tel: 0800 132 189

REF

1850

4334

0 R

ev A

200

4-03

en

Patient Interface Setup GuidePatient Interface Setup Guide

INTERNATIONAL P O Box 14 348, Panmure, Auckland 1134, New Zealand Tel:+64 9 574 0100 Fax: +64 9 574 0158 Email: [email protected] Web Site: www.fphcare.com USA Tel: 1800 446 3908 or +1 949 470 3900 Fax:+1 949 470 3933 AUSTRALIA Tel:+61 3 9879 5022 Fax: +61 3 9879 5232 AUSTRIA Tel: 0800 29 31 23 Fax: 0800 29 31 22 BENELUX Tel: +31 78 644 0924 Fax: +31 78 644 0914 CHINA Tel: +86 20 8363 4286 Fax:+86 20 8363 3595 FRANCE Tel:+33 1 6446 5201 Fax:+33 1 6446 5221 GERMANY Tel: +49 7182 93777 0 Fax: +49 7182 93777 99 IRISH REPUBLIC Tel: 1800 409 011 ITALY Tel: +39 06 7839 2939 Fax: +39 06 7814 7709 SPAIN Tel: +34 902 013 346 Fax: +34 902 013 379 UK (EU Authorised Representative) Tel: +44 1628 626 136 Fax: +44 1628 626 146 NTHN IRELAND Tel: 0800 132 189

Measure the baby’s head circumference in centimeters. Choose the correct sized bonnet. The bonnet should be snug fitting.Stretch the bonnet with your hands initially for ease of placement.

Slip the bonnet onto the baby’s head completely covering the ears and with the back edge of the bonnet at the base of the neck. The front edge of the bonnet should be just above or on the eyebrows.

Use the prong-sizing guide to choose the suitable prongs. Prongs should fill the nares completely without stretching the skin. Use the biggest possible size.

Choose the correct length of the nasal tubing. The following may be used as a guide: 50mm 1kg or less, 70mm 2kg or less, 100mm 2kg or more

Check the height of the nasal tubing on the baby’s forehead. The nasal tubing should be parallel to the infant’s face not slanted upwards or downwards. If needed, remove the tear-off strips (there are 2, remove as needed) at the bottom of the foam block along the tri-lumen tube. Note: The tear-off strip may be replaced if removed inadvertently.

Attach the prongs to the nasal tubing. Squeeze the prongs to open up the slots at the sides. Insert one end of the prongs into the triangular plastic block at the end of the nasal tubing. Work the prongs along the rest of the block to lock the prongs in place. The rectangular portion of the nasal prongs should sit within the base of the triangular plastic block.

Attach the circuits to the nasal tubing. Blue inspiratory limb to the blue collapsible extension and white expiratory limb to white collapsible extension. Ensure that the gas flow has been set and turned on before connecting to the baby. Operational Input flow range is 4 - 15 L/min (max). Recommended Input flow range is 6 - 8 L/min.

Clear nasal secretions before inserting the nasal prongs. Insert the nasal prongs curve down into the infant’s nose then rotate the nasal tubing until the foam block rests on the velcro strap on the baby’s forehead. Ensure that the nasal prongs sit well inside the nose following the anatomical curve.

Leave at least a 2mm gap between the prongs and septum. The foam block on the nasal tubing should sit at the middle of the bluevelcro strap of the bonnet just above the infant’s forehead. Place the strap over the foam block and tighten it to hold the tubing firmly in place.

Hook the clips from the side straps of the bonnet to the glider. Pull both straps at the same time for central positioning and until there is a slight bend on the glider. Affix the ends of the straps to the velcro at the sides of the bonnet.

The circuit should be kept below the level of the nasal tubing to minimize condensate at the baby. The use of angel frames, x-mas trees or similar devices are not recommended as they cause the circuit position to be elevated and restrict the movement of the baby’s head.

The key to a successful setup is keeping the nasal tubing in place. Ensure the weight of the circuit is supported to reduce tension on the nasal tubing. The circuit must have free movement to allow the baby’s head to move without restriction.

� � �

� � �

� �

� �

�

�

�In an incubator setting, it is recommended that the circuits exit the incubator through the side corner hole.

Should there be a need to raise the head of the bed, the baby should be supported to prevent him/her from sliding down and dislodging the prongs.

0123

✓✗

Nasal Tubing

Product Code Description Length (mm)

BC180-05* Nasal Tubing 50mm 50mm



BC190-05** Nasal Tubing 50mm 50mm



Nasal Tubing (5 units/bx) * For use with Fisher & Paykel inspiratory heated breathing circuit** For use with the Cardinal circuit

Nasal Prongs

Product Code Description Size - diameter of nares / width of septum

BC3520-10 Nasal Prongs 3520 3.5mm / 2.0mm









Nasal Prongs (10 units/bx)

Infant Bonnets

Product Code Description Sizehead circumference (cm)

BC300-05 Infant Bonnet 17-22cm 17cm-22cm




Infant Bonnets (5 units/bx)

Head Gear


BC325-05 Headgear Midline 29cm-36cm



Headgear (5 units/bx)

Chin Straps


BC351-10 Chinstrap 20-26cm 20cm-26cm




Chin Straps (10 units/bx)

Infant CPAP Patient Interface Ordering Information

Nasal Tubing

Nasal Prongs

Infant Bonnet

Starter Kits BC180 BC181 BC182 BC190 BC191 BC192 BC3520 BC4030 BC4540 BC5040 BC5050 BC5550 BC5560 BC6060 BC6070 BC300 BC303 BC306 BC309

BC260-SK 2 3 4 4 4 4 4 3 2

BC360-SK 2 3 3 2

BC480-SK* 3 2 2 2 1 1 2 1

BC481-SK* 3 2 2 2 1 1 2 1

BC482-SK* 3 2 2 2 1 1 2 1

BC490-SK** 3 2 2 2 1 1 2 1

BC491-SK** 3 2 2 2 1 1 2 1

BC492-SK** 3 2 2 2 1 1 2 1

* For use with Fisher & Paykel inspiratory heated breathing circuit** For use with the Cardinal circuit

Product SpecificationDelivery System Maximum Input Flow 15L/min

Maximum Mean CPAP 15cm H2O

Nasal Tubing*

Dead Space nil

Length of nasal tubingwith collapsible extension

50mm (expanded) (collapsed) 70mm (expanded) (collapsed)100mm (expanded) (collapsed)

224mm163mm244mm183mm274mm213mm

Resistance to Flow F&P Patient Interface with both inspiratory and expiratory collapsible extensions

50mm nasal tubing 70mm nasal tubing100mm nasal tubing

0.49cm H2O @ 6L/min0.53cm H2O @ 6L/min0.55cm H2O @ 6L/min

Nasal Prongs*

Material Silicone (latex free)

Hardness 80 shore A

Resistance to Flow Measured at the pressure port of the nasal tubingBC3520 prongsBC4540 prongsBC6070 prongs

2.4cm H2O @ 6L/min0.6cm H2O @ 6L/min0.2cm H2O @ 6L/min

Dead SpaceBC3520 prongsBC6070 prongs

0.1ml0.5ml

Infant Bonnet*

Bonnet tube material Cotton/nylon blend (latex free)

Headgear*

Headgear material Nylon/neoprene laminate (latex free)

Chinstrap*

Chinstrap material Nylon/polyurethane laminate (latex free)

* single patient use

infant cpap patient interface - rt connection · bc480-sk* 3 2221 121 bc481-sk* 3 2221 121...

Documents